www.clare.com
DS-CPC1976-R02 1
CPC1976
AC Power Switch
RoHS
2002/95/EC e3
Pb
Part # Description
CPC1976Y 4-Pin SIP (25/Tube)
Parameter Rating Units
AC Operating Voltage 20 - 240 Vrms
Load Current 2 Arms
On-State Voltage Drop 1.15 Vrms (at IL = 2Arms)
Blocking Voltage 600 VP
Applications
Features
Description
Ordering Information
Pin Configuration
• Programmable Control
• Process Control
• Power Control Panels
• Remote Switching
• Gas Pump Electronics
• Contactors
• Large Relays
• Solenoids
• Motors
• Heaters
• Load Current up to 2Arms
• 600VP Blocking Voltage
• 5mA Sensitivity
• Zero-Crossing Detection
• DC Control, AC Output
• Optically Isolated
• TTL and CMOS Compatible
• Low EMI and RFI Generation
• High Noise Immunity
• Machine Insertable, Wave Solderable
CPC1976 is an AC Solid State Switch utilizing
dual power SCR thyristor outputs. This device also
includes zero-cross turn-on circuitry and is specified
with a blocking voltage of 600VP .
In addition, tightly controlled zero-cross circuitry
ensures low noise switching of AC loads by
minimizing the generation of transients. The optically
coupled input and output circuits provide 3750Vrms of
isolation and noise immunity between the control and
load circuits. As a result, the CPC1976 is well suited
for industrial environments where electromagnetic
interference would disrupt the operation of plant facility
communication and control systems.
Approvals
• UL 508 Recognized Component: File #: E69938
• CSA Certified Component: Certificate #: 1172007
2
1
– LED + LED AC Load AC Load
4
3
ZC
www.clare.com
2
CPC1976
R02
Absolute Maximum Ratings are stress ratings. Stresses in
excess of these ratings can cause permanent damage to
the device. Functional operation of the device at conditions
beyond those indicated in the operational sections of this
data sheet is not implied.
Absolute Maximum Ratings (@ 25˚ C)
Parameter Ratings Units
Blocking Voltage (VDRM) 600 VP
Reverse Input Voltage 5 V
Input Control Current 50 mA
Peak (10ms) 1 A
Input Power Dissipation 1150 mW
Total Power Dissipation 22400 mW
Isolation voltage Input to Output 3750 Vrms
Operational Temperature -40 to +85 °C
Storage Temperature -40 to +125 °C
1 Derate Linearly 1.33 mW / ºC
2 Derate Linearly 20 mW / ºC
Electrical Characteristcs
Parameters Conditions Symbol Min Typ Max Units
Output Characteristics @ 25°C
Load Current, Continuous VL=120-240Vrms IL0.005 - 2 Arms
Maximum Surge Current t < 16ms IPK --20 A
Off State Leakage Current VDRM I
LEAK --1 mA
On-State Voltage Drop 1IL=2Arms - - 0.86 1.15 Vrms
Critical Rate of Rise - dv/dt 1000 1200 - V/μs
Switching Speeds
Turn-on IF = 5 mA tON - - 0.5 cycles
Turn-off tOFF - - 0.5 cycles
Zero-Cross Turn-On Voltage 1st half cycle - - 2 10 V
Subsequent half cycle - - - 2 V
Holding Current - IH- 0.82 5 mA
Latching Current - IL- 0.84 6 mA
Operating Frequency 2- 20 - 500 Hz
Load Power Factor for
Guaranteed Turn-On 360Hz PF 0.25 - - -
Input Characteristics @ 25°C
Input Control Current 460Hz IF--5 mA
Input Drop-out Voltage - - 0.8 - - V
Input Voltage Drop IF=5mA VF0.9 1.2 1.4 V
Reverse Input Current VR=5V IR--10 μA
Common Characteristics @ 25°C
Input to Output Capacitance - CI/O --3 pF
1 Tested at a peak value equivalent.
2 Zero Cross 1st half cycle @ <100Hz.
3 Snubber circuits may be required at low power factors.
4 For high-noise environments, or for high-frequency operation, use IF > 10mA.
CPC1976
www.clare.com 3
R02
PERFORMANCE DATA*
* The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our application
department.
LED Forward Voltage (V)
1.25 1.26 1.27 1.28 1.29 1.30
Device Count (N)
0
5
10
15
20
25
30
35
Typical LED Forward Voltage Drop
Distribution
(N=50, TA=25ºC, IF=5mA)
On-State Voltage Drop (VP)
1.007 1.009 1.011 1.013 1.015 1.017 1.019
Device Count (N)
0
5
10
15
20
25
Typical On-State Voltage Drop
Distribution
(N=50, TA=25ºC, IL=2ADC, IF=5mA)
LED Current (mA)
1.6 2.0 2.4 2.8 3.2 3.6 4.0
Device Count (N)
0
5
10
15
20
25
LED Current to Operate Distribution
(N=50, TA=25ºC, VL=120VAC/60Hz)
Blocking Voltage (VP)
780 810 840 870 900 930 960
Device Count (N)
0
5
10
15
20
Typical Blocking Voltage Distribution
(N=50, TA=25ºC)
Temperature (ºC)
-40 -20 0 20 40 60 80 100
Blocking Voltage (VP)
760
800
840
880
920
960
Blocking Voltage vs. Temperature
Temperature (ºC)
-40 -20 0 20 40 60 80 100
Leakage Current (μA)
0.60
0.62
0.64
0.66
0.68
0.70
0.72
Leakage Current
(VL=600VP)
Temperature (ºC)
-40 -20 0 20 40 60 80 100
Holding Current (μA)
162.0
162.5
163.0
163.5
164.0
164.5
165.0
165.5
166.0
Holding Current
Temperature (ºC)
-40 -20 0 20 40 60 80 100
LED current (mA)
1.8
1.9
2.0
2.1
2.2
2.3
2.4
LED Current to Operate
(VL=5V / 60Hz)
Temperature (ºC)
-40 -20 0 20 40 60 80 100
Load Voltage (V)
0.75
0.80
0.85
0.90
0.95
1.00
1.05
Load Voltage vs. Temperature
(IF=5mA)
IL=2AP
IL=1.5AP
IL=1AP
IL=0.5AP
www.clare.com
4
CPC1976
R02
PERFORMANCE DATA*
* The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our application
department.
Temperature (ºC)
-40 -20 0 20 40 60 80 100
LED Forward Voltage (V)
1.1
1.2
1.3
1.4
1.5
1.6
LED Forward Voltage vs. Temperature
IF=50mA
IF=20mA
IF=10mA
IF=5mA
Load Voltage (VP)
-1.5 -1.0 -0.5 0.0 0.5 1.0 1.5
Load Current (AP)
-3
-2
-1
0
1
2
3
Load Current vs. Load Voltage
(TA=25ºC, IF=5mA)
Load Frequency (Hz)
0 100 200 300 400 500
LED Current (mA)
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
LED Current to Operate
vs. Load Frequency
(TA=25ºC, VL=137Vrms, ZL=150mH)
Time (ms)
1 10 100 1000
Load Current (AP)
0
5
10
15
20
25
Maximum Non-Repetitive Surge Current
(Values Apply to TJ=50ºC Before Surge)
16
Typical dv/dt vs. Temperature
0
800
600
400
200
1200
1000
25 50 85
Temperature (ºC)
Critical Rate of Rise (V/μs)
Vo
63%
10%
RC
Vo = 300V
dv 0.63 x 300V 189
dt RC RC
In accordance with
EIA/NARM Standards
RS-443 for Solid State Relays
dv/dt Method
Clare, Inc. makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications
and product descriptions at any time without notice. Neither circuit patent licenses nor indemnity are expressed or implied. Except as set forth in Clare’s Standard Terms and Conditions of
Sale, Clare, Inc. assumes no liability whatsoever, and disclaims any express or implied warranty, relating to its products including, but not limited to, the implied warranty of merchantability,
fitness for a particular purpose, or infringement of any intellectual property right.
The products described in this document are not designed, intended, authorized or warranted for use as components in systems intended for surgical implant into the body, or in other
applications intended to support or sustain life, or where malfunction of Clare’s product may result in direct physical harm, injury, or death to a person or severe property or environmental
damage. Clare, Inc. reserves the right to discontinue or make changes to its products at any time without notice.
Specification: DS-CPC1976-R02
©Copyright 2009, Clare, Inc.
All rights reserved. Printed in USA.
3/9/09
For additional information please visit our website at: www.clare.com
MECHANICAL DIMENSIONS
MANUFACTURING INFORMATION
Soldering
For proper assembly, the component must be
processed in accordance with the current revision
of IPC/JEDEC standard J-STD-020. Failure to
follow the recommended guidelines may cause
permanent damage to the device resulting in impaired
performance and/or a reduced lifetime expectancy.
Washing
Clare does not recommend ultrasonic cleaning or the
use of chlorinated solvents.
RoHS
2002/95/EC e3
Pb
3.302 ± 0.051
(0.130 ± 0.002)
7º TYP
4 PLCS
0.381 ± 0.013
(0.015 ± 0.0005)
21.082 ± 0.381
(0.830 ± 0.015)
10.160 ± 0.127
(0.400 ± 0.005)
0.762 ± 0.076
(0.030 ± 0.003)
2.540 ± 0.127
(0.100 ± 0.005)
10.160 ± 0.127
(0.400 ± 0.005)
5.080 ± 0.127
(0.200 ± 0.005)
1.778
(0.070)
1.016 ± 0.127
(0.040 ± 0.005)
Pin 1 Pin 4
4.572 ± 0.127
(0.180 ± 0.005)
1.651 ± 0.102
(0.065 ± 0.004)
Dimensions
mm
(inches)
Note: Recommended hole size is based on the maximum
cross-section diagonal measure of the pin plus 0.4mm (0.016).
2.540 (0.100)
12.700 (0.500)
17.780 (0.700)
Recommended Hole Pattern
4 x 1.326 (0.052) DIA.