http://www.tracopower.com
DC/DC Converters
TES 2M Series, 2 Watt
Features
◆ Ultracompact SMD-package
◆ I/O isolation 4000 VACrms rated for
working voltages up to 300 Vrms
◆ Operating temp. range –25°C to +80°C
◆ Qualified for leadfree reflow solder
process
◆ Available in tape & reel package
Ordercode Input voltage range Output voltage Output current max. Efficiency typ.
TES 2-0511M 5 VDC 400 mA 66 %
TES 2-0512M 5.0 VDC ±10% 12 VDC 165 mA 66 %
TES 2-0513M (nominal 05 VDC) 15 VDC 133 mA 66 %
TES 2-0522M ±12 VDC ±83 mA 72 %
TES 2-0523M ±15 VDC ±66 mA 73 %
TES 2-1211M 5 VDC 400 mA 66 %
TES 2-1212M 12.0 VDC ±10% 12 VDC 165 mA 66 %
TES 2-1213M (nominal 12 VDC) 15 VDC 133 mA 66 %
TES 2-1222M ±12 VDC ±83 mA 74 %
TES 2-1223M ±15 VDC ±66 mA 75 %
TES 2-2411M 5 VDC 400 mA 66 %
TES 2-2412M 24 VDC ±10% 12 VDC 165 mA 66 %
TES 2-2413M (nominal 24 VDC) 15 VDC 133 mA 66 %
TES 2-2422M ±12 VDC ±83 mA 74 %
TES 2-2423M ±15 VDC ±66 mA 75 %
Models
The TES 2M series is range of compact 2W DC/DC-converters providing a high
I/O-isolation voltage of 4000 VAC. With a reinforced I/O-isolation system this pro-
duct is an economical solution for many applications in instrumentation, industrial
controls, medical equipment and everywhere where supplementary- or reinforced
insulation is required.
These converters are qualified for high solder temperature profiles in leadfree sol-
der processes. For automated SMD production lines the devices can be supplied
in tape & reel package. Full SMD-design with exclusive use of ceramic capacitors
ensure a very high reliability and a long product lifetime.
Page 1 of 3
C B
Scheme
IEC 60950-1
IEC 60601-1
pending
http://www.tracopower.com
DC/DC Converters
TES 2M Series 2 Watt
Input Specifications
Input current no load 5 Vin models: 60 mA typ.
12 Vin models: 30 mA typ.
24 Vin models: 15 mA typ.
Reverse voltage protection 0.3 A max.
Recommended input fuse (slow blow) 5 Vin models: 1.0 A
12 Vin models: 0.5 A
24 Vin models: 0.2 A
Surge voltage (1 sec. max.) 5 Vin models: 9 V max.
12 Vin models: 18 V max.
24 Vin models: 30 V max.
Input filter internal capacitors
Output Specifications
Voltage set accuracy ±4 %
Voltage balance (dual output models) 1 % max.
Regulation – Input variation 1.2 % / 1 % change of Vin
– Load variation 20 – 100 % 10 % max.
12 % max. for 5 Vout models.
Ripple and noise (20 MHz Bandwidth) 150 mVp-p max.
Temperature coefficient ±0.02 %/K
Short circuit protection 0.5 sec. max.
Minimum load 2 % of rated max current.
Capacitive load single output models: 330 µF max.
dual output models: 100 µF max. (each output)
General Specifications
Temperature ranges – Operating –25°C to +80°C
– Storage –55°C to +125°C
– Case temperature +90°C max.
Derating 2.5 %/K above 60°C
Humidity (non condensing) 95 % rel. H max.
Reliability, calculated MTBF (MIL-HDBK-217F at +25°C, ground benign) >2.0 Mio h
Isolation voltage (50Hz, 60sec.) – Input/Output 4000 VACrms
Isolation test voltage (1 sec.) 6000 Vpk
Leakage current (at 240VAC, 60Hz) 2 µA max.
Isolation capacitance – Input/Output 20 pF max. (at 100KHz, 1V)
Isolation resistance – Input/Output >10 Gohm (at 500VDC)
Safety standards IEC/EN 60950-1,
IEC/EN 60601-1 3rd edition, 2 x MOOP
cUL/UL 60950-1, UL 60601-1
Safety approvals – CB test certificate (IEC 60950-1& IEC60601-1) www.tracopower.com/products/tes2m-cb.pdf
Switching frequency 50 – 100 kHz (PFM)
Environmental compliance – Reach www.tracopower.com/products/tes2m-reach.pdf
– RoHS directive 2011/65/EU
All specifications valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated.
Page 2 of 3
pending
Specifications can be changed without notice! Make sure you are using the latest documentation, downloadable at www.tracopower.com
www.tracopower.com
DC/DC Converters
TES 2M Series 2 Watt
Rev. April 10. 2013
Page 3 of 3
Outline Dimensions
Pin Single Dual
1–Vin (GND) –Vin (GND)
7No con. No con.
8No con. Common
9+Vout +Vout
10 –Vout –Vout
16 +Vin +Vin
Pin-Out
Physical Specifications
Casing material plastic
Weight 3.8 g (0.13oz)
Lead-free reflow solder process as per J-STD-020D.01 (to find at:
www.jedec.org - free registration required)
Moisture sensivity level (MSL) level 2 as per J-STD-033B.01 (to find at:
www.jedec.org - free registration required)
Washing process w ww.tracopower.com/products/smd- wash.pdf
Packaging www.tracopower.com/products/tes2m-pack.pdf
Dimensions in [mm], () = Inch
Tolerances ±0.25 (±0.01)
Pin pitch tolerances ±0.05 (±0.002)
24.0 (0.94)
0.25 (0.01)
9.0 (0.35)
18.1 (0.71)
13.7 (0.54)
15.24 (0.60) 2.54 (0.10)
3.11 (0.12)
top view
178
16 10 9
0 - 4°
0.15
1.0 (0.04)
2.8
(0.11)
13.7 (0.54)
15.24 (0.60) 2.54 (0.10)
3.11 (0.12)
1.4 (0.055) min.
2.8
(0.11)
Solder Pad Dimension
Application note: www.tracopower.com/products/tes2m-application.pdf
