MC10EP58, MC100EP58 3.3V / 5VECL 2:1 Multiplexer The MC10/100EP58 is a 2:1 multiplexer. The device is pin and functionally equivalent to the EL58 and LVEL58 devices. The 100 Series contains temperature compensation. * 310 ps Typical Propagation Delay * Maximum Frequency > 3 GHz Typical * PECL Mode Operating Range: VCC = 3.0 V to 5.5 V * http://onsemi.com MARKING DIAGRAMS* with VEE = 0 V NECL Mode Operating Range: VCC = 0 V with VEE = -3.0 V to -5.5 V Open Input Default State 8 8 * * Q Output Will Default LOW with Inputs Open or at VEE 8 HEP58 ALYW 1 SO-8 D SUFFIX CASE 751 1 1 8 8 8 HP58 ALYW 1 TSSOP-8 DT SUFFIX CASE 948R KEP58 ALYW 1 KP58 ALYW 1 H = MC10 K = MC100 A = Assembly Location L = Wafer Lot Y = Year W = Work Week ORDERING INFORMATION Device Semiconductor Components Industries, LLC, 2001 April, 2001 - Rev. 3 1 Package Shipping MC10EP58D SO-8 98 Units/Rail MC10EP58DR2 SO-8 2500 Tape & Reel MC100EP58D SO-8 98 Units/Rail MC100EP58DR2 SO-8 2500 Tape & Reel MC10EP58DT TSSOP-8 100 Units/Rail MC10EP58DTR2 TSSOP-8 2500 Tape & Reel MC100EP581DT TSSOP-8 MC100EP58DTR2 TSSOP-8 2500 Tape & Reel 100 Units/Rail Publication Order Number: MC10EP58/D MC10EP58, MC100EP58 PIN DESCRIPTION NC Da 1 8 2 7 1 VCC 3 6 0 FUNCTION Da*, Db* ECL Data Inputs SEL* ECL Select Inputs Q, Q ECL Data Outputs VCC Positive Supply VEE Negative Supply NC No Connect Q MUX Db PIN Q * Pins will default LOW when left open. SEL 4 5 VEE TRUTH TABLE SEL Data H L a b Figure 1. 8-Lead Pinout (Top View) and Logic Diagram ATTRIBUTES Characteristics Value Internal Input Pulldown Resistor 75 k Internal Input Pullup Resistor ESD Protection N/A Human Body Model Machine Model Charged Device Model > 4 kV > 200 V > 2 kV Moisture Sensitivity, Indefinite Time Out of Drypack (Note 1.) Level 1 Flammability Rating Oxygen Index UL-94 code V-0 A 1/8" 28 to 34 Transistor Count 41 Devices Meets or exceeds JEDEC Spec EIA/JESD78 IC Latchup Test 1. For additional information, see Application Note AND8003/D. MAXIMUM RATINGS (Note 2.) Symbol Parameter Condition 1 Condition 2 Rating Units VCC PECL Mode Power Supply VEE = 0 V 6 V VEE NECL Mode Power Supply VCC = 0 V -6 V VI Input PECL Mode In ut Voltage NECL Mode Input Voltage VEE = 0 V VCC = 0 V 6 -6 V V Iout Output Current Continuous Surge 50 100 mA mA IBB VBB Sink/Source 0.5 mA TA Operating Temperature Range -40 to +85 C Tstg Storage Temperature Range -65 to +150 C JA Thermal Resistance (Junction to Ambient) 0 LFPM 500 LFPM 8 SOIC 8 SOIC 190 130 C/W C/W JC Thermal Resistance (Junction to Case) std bd 8 SOIC 41 to 44 C/W JA Thermal Resistance (Junction to Ambient) 0 LFPM 500 LFPM 8 TSSOP 8 TSSOP 185 140 C/W C/W JC Thermal Resistance (Junction to Case) std bd 8 TSSOP 41 to 44 C/W Tsol Wave Solder <2 to 3 sec @ 248C 265 C 2. Maximum Ratings are those values beyond which device damage may occur. http://onsemi.com 2 VI VCC VI VEE MC10EP58, MC100EP58 10EP DC CHARACTERISTICS, PECL VCC = 3.3 V, VEE = 0 V (Note 3.) -40C Symbol Characteristic 25C 85C Min Typ Max Min Typ Max Min Typ Max Unit 20 28 37 20 30 39 22 31 40 mA IEE Power Supply Current VOH Output HIGH Voltage (Note 4.) 2165 2290 2415 2230 2355 2480 2290 2415 2540 mV VOL Output LOW Voltage (Note 4.) 1365 1490 1615 1430 1555 1680 1490 1615 1740 mV VIH Input HIGH Voltage (Single Ended) 2090 2415 2155 2480 2215 2540 mV VIL Input LOW Voltage (Single Ended) 1365 1690 1460 1755 1490 1815 mV IIH Input HIGH Current 150 A IIL Input LOW Current 150 150 0.5 0.5 A 0.5 NOTE: EP circuits are designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse airflow greater than 500 lfpm is maintained. 3. Input and output parameters vary 1:1 with VCC. VEE can vary +0.3 V to -2.2 V. 4. All loading with 50 ohms to VCC-2.0 volts. 10EP DC CHARACTERISTICS, PECL VCC = 5.0 V, VEE = 0 V (Note 5.) -40C Symbol Characteristic 25C 85C Min Typ Max Min Typ Max Min Typ Max Unit 20 28 37 20 30 39 22 31 40 mA IEE Power Supply Current VOH Output HIGH Voltage (Note 6.) 3865 3990 4115 3930 4055 4180 3990 4115 4240 mV VOL Output LOW Voltage (Note 6.) 3065 3190 3315 3130 3255 3380 3190 3315 3440 mV VIH Input HIGH Voltage (Single Ended) 3790 4115 3855 4180 3915 4240 mV VIL Input LOW Voltage (Single Ended) 3065 3390 3130 3455 3190 3515 mV IIH Input HIGH Current 150 A IIL Input LOW Current 150 150 0.5 0.5 A 0.5 NOTE: EP circuits are designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse airflow greater than 500 lfpm is maintained. 5. Input and output parameters vary 1:1 with VCC. VEE can vary +2.0 V to -0.5 V. 6. All loading with 50 ohms to VCC-2.0 volts. 10EP DC CHARACTERISTICS, NECL VCC = 0 V, VEE = -5.5 V to -3.0 V (Note 7.) -40C Symbol Characteristic 25C 85C Min Typ Max Min Typ Max Min Typ Max Unit 20 28 37 20 30 39 22 31 40 mA IEE Power Supply Current VOH Output HIGH Voltage (Note 8.) -1135 -1010 -885 -1070 -945 -820 -1010 -885 -760 mV VOL Output LOW Voltage (Note 8.) -1935 -1810 -1685 -1870 -1745 -1620 -1810 -1685 -1560 mV VIH Input HIGH Voltage (Single Ended) -1210 -885 -1145 -820 -1085 -760 mV VIL Input LOW Voltage (Single Ended) -1935 -1610 -1870 -1545 -1810 -1485 mV IIH Input HIGH Current 150 A IIL Input LOW Current 150 0.5 150 0.5 0.5 A NOTE: EP circuits are designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse airflow greater than 500 lfpm is maintained. 7. Input and output parameters vary 1:1 with VCC. 8. All loading with 50 ohms to VCC-2.0 volts. http://onsemi.com 3 MC10EP58, MC100EP58 100EP DC CHARACTERISTICS, PECL VCC = 3.3 V, VEE = 0 V (Note 9.) -40C Symbol Characteristic 25C 85C Min Typ Max Min Typ Max Min Typ Max Unit 20 28 37 20 31 39 25 33 42 mA IEE Power Supply Current VOH Output HIGH Voltage (Note 10.) 2155 2280 2405 2155 2280 2405 2155 2280 2405 mV VOL Output LOW Voltage (Note 10.) 1355 1480 1605 1355 1480 1605 1355 1480 1605 mV VIH Input HIGH Voltage (Single Ended) 2075 2420 2075 2420 2075 2420 mV VIL Input LOW Voltage (Single Ended) 1355 1675 1355 1675 1355 1675 mV IIH Input HIGH Current 150 A IIL Input LOW Current 150 150 0.5 0.5 A 0.5 NOTE: EP circuits are designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse airflow greater than 500 lfpm is maintained. 9. Input and output parameters vary 1:1 with VCC. VEE can vary +0.3 V to -2.2 V. 10. All loading with 50 ohms to VCC-2.0 volts. 100EP DC CHARACTERISTICS, PECL VCC = 5.0 V, VEE = 0 V (Note 11.) -40C Symbol Characteristic 25C 85C Min Typ Max Min Typ Max Min Typ Max Unit 20 28 37 20 31 39 25 33 42 mA IEE Power Supply Current VOH Output HIGH Voltage (Note 12.) 3855 3980 4105 3855 3980 4105 3855 3980 4105 mV VOL Output LOW Voltage (Note 12.) 3055 3180 3305 3055 3180 3305 3055 3180 3305 mV VIH Input HIGH Voltage (Single Ended) 3775 4120 3775 4120 3775 4120 mV VIL Input LOW Voltage (Single Ended) 3055 3375 3055 3375 3055 3375 mV IIH Input HIGH Current 150 A IIL Input LOW Current 150 150 0.5 0.5 A 0.5 NOTE: EP circuits are designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse airflow greater than 500 lfpm is maintained. 11. Input and output parameters vary 1:1 with VCC. VEE can vary +2.0 V to -0.5 V. 12. All loading with 50 ohms to VCC-2.0 volts. 100EP DC CHARACTERISTICS, NECL VCC = 0 V, VEE = -5.5 V to -3.0 V (Note 13.) -40C Symbol Characteristic 25C 85C Min Typ Max Min Typ Max Min Typ Max Unit 20 28 37 20 31 39 25 33 42 mA IEE Power Supply Current VOH Output HIGH Voltage (Note 14.) -1145 -1020 -895 -1145 -1020 -895 -1145 -1020 -895 mV VOL Output LOW Voltage (Note 14.) -1945 -1820 -1695 -1945 -1820 -1695 -1945 -1820 -1695 mV VIH Input HIGH Voltage (Single Ended) -1225 -880 -1225 -880 -1225 -880 mV VIL Input LOW Voltage (Single Ended) -1945 -1625 -1945 -1625 -1945 -1625 mV IIH Input HIGH Current 150 A IIL Input LOW Current 150 0.5 150 0.5 0.5 A NOTE: EP circuits are designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse airflow greater than 500 lfpm is maintained. 13. Input and output parameters vary 1:1 with VCC. 14. All loading with 50 ohms to VCC-2.0 volts. http://onsemi.com 4 MC10EP58, MC100EP58 AC CHARACTERISTICS VCC = 0 V; VEE = -3.0 V to -5.5 V or VCC = 3.0 V to 5.5 V; VEE = 0 V (Note 15.) -40C Symbol Characteristic Min fmax Maximum Frequency (See Figure 2. Fmax/JITTER) tPLH, tPHL Propagation Delay to Output Differential tJITTER Cycle-to-Cycle Jitter (See Figure 2. Fmax/JITTER) VPP Input Voltage Swing (Differential) tr tf Output Rise/Fall Times (20% - 80%) 25C Typ Max Min >3 Typ 85C Max Min >3 Typ >3 Q, Q 200 280 380 0.2 <2 150 800 1200 70 120 170 210 310 410 0.2 <2 150 800 1200 80 130 180 220 GHz 340 420 0.2 <2 ps 150 800 1200 mV 100 150 200 ps 1000 10 900 9 800 8 700 7 600 6 500 5 400 4 300 3 200 2 EEEEEEEEEE EEEEEEEEEE EEEEEEEEEE 100 EE EE EE (JITTER) 1 0 1000 2000 3000 4000 FREQUENCY (MHz) Figure 2. Fmax/Jitter http://onsemi.com 5 JITTEROUT ps (RMS) VOUTpp (mV) Unit ps D to Q,Q SEL to Q,Q 15. Measured using a 750 mV source, 50% duty cycle clock source. All loading with 50 ohms to V CC-2.0 V. 0 Max 5000 6000 MC10EP58, MC100EP58 Q D Receiver Device Driver Device Qb Db 50 50 V TT V TT = V CC - 2.0 V Figure 3. Typical Termination for Output Driver and Device Evaluation (See Application Note AND8020 - Termination of ECL Logic Devices.) Resource Reference of Application Notes AN1404 - ECLinPS Circuit Performance at Non-Standard VIH Levels AN1405 - ECL Clock Distribution Techniques AN1406 - Designing with PECL (ECL at +5.0 V) AN1504 - Metastability and the ECLinPS Family AN1568 - Interfacing Between LVDS and ECL AN1650 - Using Wire-OR Ties in ECLinPS Designs AN1672 - The ECL Translator Guide AND8001 - Odd Number Counters Design AND8002 - Marking and Date Codes AND8009 - ECLinPS Plus Spice I/O Model Kit AND8020 - Termination of ECL Logic Devices For an updated list of Application Notes, please see our website at http://onsemi.com. http://onsemi.com 6 MC10EP58, MC100EP58 PACKAGE DIMENSIONS SO-8 D SUFFIX PLASTIC SOIC PACKAGE CASE 751-07 ISSUE W -X- NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. A 8 5 0.25 (0.010) S B 1 M Y M 4 K -Y- G C N DIM A B C D G H J K M N S X 45 SEATING PLANE -Z- 0.10 (0.004) H M D 0.25 (0.010) M Z Y X S J S MILLIMETERS MIN MAX 4.80 5.00 3.80 4.00 1.35 1.75 0.33 0.51 1.27 BSC 0.10 0.25 0.19 0.25 0.40 1.27 0 8 0.25 0.50 5.80 6.20 INCHES MIN MAX 0.189 0.197 0.150 0.157 0.053 0.069 0.013 0.020 0.050 BSC 0.004 0.010 0.007 0.010 0.016 0.050 0 8 0.010 0.020 0.228 0.244 TSSOP-8 DT SUFFIX PLASTIC TSSOP PACKAGE CASE 948R-02 ISSUE A 8x 0.15 (0.006) T U K REF 0.10 (0.004) S 2X L/2 8 1 PIN 1 IDENT S T U V S NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH. PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 6. DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE -W-. S 5 0.25 (0.010) B -U- L 0.15 (0.006) T U M M 4 A -V- F DETAIL E C 0.10 (0.004) -T- SEATING PLANE D -W- G DETAIL E http://onsemi.com 7 DIM A B C D F G K L M MILLIMETERS MIN MAX 2.90 3.10 2.90 3.10 0.80 1.10 0.05 0.15 0.40 0.70 0.65 BSC 0.25 0.40 4.90 BSC 0 6 INCHES MIN MAX 0.114 0.122 0.114 0.122 0.031 0.043 0.002 0.006 0.016 0.028 0.026 BSC 0.010 0.016 0.193 BSC 0 6 MC10EP58, MC100EP58 ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. PUBLICATION ORDERING INFORMATION NORTH AMERICA Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: ONlit@hibbertco.com Fax Response Line: 303-675-2167 or 800-344-3810 Toll Free USA/Canada N. American Technical Support: 800-282-9855 Toll Free USA/Canada EUROPE: LDC for ON Semiconductor - European Support German Phone: (+1) 303-308-7140 (Mon-Fri 2:30pm to 7:00pm CET) Email: ONlit-german@hibbertco.com French Phone: (+1) 303-308-7141 (Mon-Fri 2:00pm to 7:00pm CET) Email: ONlit-french@hibbertco.com English Phone: (+1) 303-308-7142 (Mon-Fri 12:00pm to 5:00pm GMT) Email: ONlit@hibbertco.com CENTRAL/SOUTH AMERICA: Spanish Phone: 303-308-7143 (Mon-Fri 8:00am to 5:00pm MST) Email: ONlit-spanish@hibbertco.com Toll-Free from Mexico: Dial 01-800-288-2872 for Access - then Dial 866-297-9322 ASIA/PACIFIC: LDC for ON Semiconductor - Asia Support Phone: 303-675-2121 (Tue-Fri 9:00am to 1:00pm, Hong Kong Time) Toll Free from Hong Kong & Singapore: 001-800-4422-3781 Email: ONlit-asia@hibbertco.com JAPAN: ON Semiconductor, Japan Customer Focus Center 4-32-1 Nishi-Gotanda, Shinagawa-ku, Tokyo, Japan 141-0031 Phone: 81-3-5740-2700 Email: r14525@onsemi.com ON Semiconductor Website: http://onsemi.com EUROPEAN TOLL-FREE ACCESS*: 00-800-4422-3781 *Available from Germany, France, Italy, UK, Ireland For additional information, please contact your local Sales Representative. http://onsemi.com 8 MC10EP58/D