SF2138B * * * * * Designed for SDARS IF Receiver Low Insertion Loss 5.0 X 7.0 mm Surface-Mount Case Differential or Single Ended Input and Output Complies with Directive 2002/95/EC (RoHS) 144.132 MHz SAW Filter Pb Absolute Maximum Ratings Rating Value Units Maximum Incident Power in Passband +10 dBm Maximum DC Voltage Between any Two Terminals 30 VDC -40 to +85 C Storage Temperature Range in Tape an Reel Maximum Soldering Profile 265 C for 10 s SMP-03 Electrical Characteristics Characteristic Nominal Center Frequency Passband Width at +25 C 1 dB Bandwidth 15 dB Bandwidth 30 dB Bandwidth Passband Minimum Insertion Loss, Including Matching Network Terminating Source Impedance Terminating Load Impedance Amplitude Ripple: TDM1, 137.882 to 142.382 MHz COFDM, 141.882 to 146.182 MHz TDM2, 145.882 to 150.382 MHz Attenuation Relative to Insertion Loss at Center Frequency 122.882 to 127.882 MHz 127.882 to 132.882 MHz 154.137 to 159.137 MHz 159.137 to 162.882 MHz 162.882 to 177.882 MHz Group Delay Ripple TDM1, 137.882 to 142.382 MHz COFDM, 141.882 to 146.182 MHz TDM2, 145.882 to 150.382 MHz Operating Temperature Range Case Style Lid Symbolization (YY=year, WW=week, S=shift) See note 4 Sym Notes fC 1 BW1 BW15 BW30 ILMIN Min Typ Max 144.132 137.882 12.5 150.382 13.3 15.9 16.2 16.9 18.2 13.7 15.5 ZS = 200 ohms differential ZL = 1.5K ohms differential 1 1 0.5 1 45 43 38 43 48 1, 3 50 47 42 47 53 1.7 1.5 1.7 Units MHz dB MHz MHz MHz dB dBP-P dBc 30 25 30 TA 1 6 100 nsP-P 100 100 -40 +85 C SMP-03 7 x 5 mm Nominal Footprint RFM SF2138B YYWWS CAUTION: Electrostatic Sensitive Device. Observe precautions for handling. Notes: 1. 2. 3. 4. 5. 6. 7. 8. 9. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to 50 and measured with 50 network analyzer. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external impedance matching design. See Application Note No. 42 for details. "LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes." The design, manufacturing process, and specifications of this filter are subject to change. Tape and Reel Standard ANSI / EIA 481. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port 2, so that the filter must always be installed in one direction per the circuit design. US and international patents may apply. RFM, stylized RFM logo, and RF Monolithics, Inc. are registered trademarks of RF Monolithics, Inc. www.RFM.com E-mail: info@rfm.com (c)2009 by RF Monolithics, Inc. Page 1 of 6 SF2138B - 7/9/09 C1 9 L1 J1 8 7 10 5.6PF 200OHMS 100NH 4.7PF 5 2 3 C3 1.5Kohms L4 1 5.6PF J3 150NH SF2138B DEMO C2 J2 L3 6 J4 4 150NH PCB, IND, IND, CAP, CAP, 400-1749-001 501-0782-101 501-0782-151 501-1275-056 501-1275-047 www.RFM.com E-mail: info@rfm.com (c)2009 by RF Monolithics, Inc. 0805 COIL CRAFT, 100NH 0805 COIL CRAFT, 150NH 0805, 5.6PF 0805, 4.7PF L1 L2, L3 C1, C2 C3 Page 2 of 6 SF2138B - 7/9/09 www.RFM.com E-mail: info@rfm.com (c)2009 by RF Monolithics, Inc. Page 3 of 6 SF2138B - 7/9/09 www.RFM.com E-mail: info@rfm.com (c)2009 by RF Monolithics, Inc. Page 4 of 6 SF2138B - 7/9/09 SMP-03 Case 10-Terminal Ceramic Surface-Mount Case 7 x 5 mm Nominal Footprint Case Dimensions mm Dimension A B C D E H J K P Recommended PCB Footprint Inches Min Nom Max Min Nom Max 6.80 4.80 7.00 5.00 1.65 0.60 2.54 1.0 5.00 3.00 1.27 7.20 5.20 2.00 .73 2.67 1.13 5.13 3.13 1.40 0.268 0.189 0.276 0.197 0.065 0.024 0.100 0.039 0.197 0.118 0.050 0.283 0.205 0.079 0.029 0.105 0.044 0.202 0.123 0.055 .47 2.41 0.87 4.87 2.87 1.14 0.019 0.095 0.034 0.192 0.113 0.045 Materials Solder Pad Plating 0.3 to 1.0 m Gold over 1.27 to 8.89 m Nickel Lid Plating 2.0 to 3.0 m Nickel Body Al2O3 Ceramic Pb Free Electrical Connections Connection Port 1 Port 2 Terminals Input or Return 10 Return or Input 1 Output or Return 5 Return or Output 6 Ground All others Single-ended Operation Return is ground Differential Operation Return is hot C B E H H A J D P K www.RFM.com E-mail: info@rfm.com (c)2009 by RF Monolithics, Inc. Page 5 of 6 SF2138B - 7/9/09 Tape and Reel Specifications "B" REF. 100 REF. "B " Quantity Per Reel Inches millimeters 7 178 500 13 330 2000 See Detail "A" 13. 0 12.0 16.0 20 .2 2.0 COMPONENT ORIENTATION and DIMENSIONS Carrier Tape Dimensions Ao Bo Ko Pitch W 5.5 mm 7.5 mm 2.0 mm 8.0 mm 16.0 mm PIN #1 USER DIRECTION OF FEED www.RFM.com E-mail: info@rfm.com (c)2009 by RF Monolithics, Inc. Page 6 of 6 SF2138B - 7/9/09