VCUT05B1-DD1 www.vishay.com Vishay Semiconductors Bidirectional Symmetrical (BiSy) Single Line ESD-Protection Diode in LLP1006-2M FEATURES * Ultra compact LLP1006-2M package * Low package height < 0.4 mm * 1-line ESD-protection 2 1 * Working range 5.5 V * Low leakage current < 0.1 A 21129 * Low load capacitance CD = 10 pF * ESD-protection acc. IEC 61000-4-2 30 kV contact discharge 30 kV air discharge 20855 MARKING (example only) * Soldering can be checked by standard vision inspection. No X-ray necessary XY * Pin plating NiPdAu (e4) no whisker growth * Material categorization: For definitions of compliance please see www.vishay.com/doc?99912 21121 Bar = pin 1 marking X = date code Y = type code (see table below) ORDERING INFORMATION DEVICE NAME ORDERING CODE TAPED UNITS PER REEL (8 mm TAPE ON 7" REEL) MINIMUM ORDER QUANTITY VCUT05B1-DD1 VCUT05B1-DD1-G-08 8000 8000 PACKAGE DATA DEVICE NAME PACKAGE NAME TYPE CODE WEIGHT MOLDING COMPOUND FLAMMABILITY RATING MOISTURE SENSITIVITY LEVEL SOLDERING CONDITIONS VCUT05B1-DD1 LLP1006-2M P 0.72 mg UL 94 V-0 MSL level 1 (according J-STD-020) 260 C/10 s at terminals ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITIONS SYMBOL VALUE UNIT Peak pulse current acc. IEC 61000-4-5, 8/20 s/single shot IPPM 3 A Peak pulse power Pin 1 to pin 2 acc. IEC 61000-4-5; tp = 8/20 s; single shot PPP 38 W Contact discharge acc. IEC61000-4-2; 10 pulses VESD 30 Air discharge acc. IEC61000-4-2; 10 pulses VESD 30 TJ - 55 to + 145 C Tstg - 55 to + 150 C ESD immunity Operating temperature Storage temperature Rev. 1.2, 21-Jun-12 Junction temperature kV Document Number: 81149 1 For technical questions, contact: ESDprotection@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VCUT05B1-DD1 www.vishay.com Vishay Semiconductors CUT THE SPIKES WITH VCUT05B1-DD1 The VCUT05B1-DD1 is a Bidirectional and Symmetrical (BiSy) ESD-protection device which clamps positive and negative overvoltage transients to ground. Connected between the signal or data line and the ground the VCUT05B1-DD1 offers a high isolation (low leakage current, low capacitance) within the specified working range. Due to the short leads and small package size of the tiny LLP1006-2M package the line inductance is very low, so that fast transients like and ESD-strike can be clamped with minimal over- or undershoots. ELECTRICAL CHARACTERISTICS (Tamb = 25 C, unless otherwise specified) PARAMETER TEST CONDITIONS/REMARKS SYMBOL MIN. TYP. MAX. UNIT Number of lines which can be protected Nchannel - - 1 lines Max. reverse working voltage VRWM - - 5.5 V Reverse voltage at I = 0.1 A VR 5.5 - - V Reverse current at V = 5.5 V IR - - 0.1 A Reverse breakdown voltage at I = 1 mA VBR 6 7.5 8.5 V at IPP = 1 A VC - 8.3 10.5 V Protection paths Reverse stand-off voltage Reverse clamping voltage Capacitance at IPP = IPPM = 3 A VC - 10.3 12.5 V at V = 0 V; f = 1 MHz CD - 10 13 pF at V = 2.5 V; f = 1 MHz CD - 8 - pF TYPICAL CHARACTERISTICS (Tamb = 25 C, unless otherwise specified) 120 % 12 f = 1 MHz Rise time = 0.7 ns to 1 ns 80 % 8 CD (pF) 10 Discharge Current IESD 100 % 60 % 53 % 6 40 % 4 27 % 20 % 2 0% - 10 0 10 20 30 40 50 60 70 80 90 100 0 1 2 21792 Time (ns) 20557 0 Fig. 1 - ESD Discharge Current Wave Form acc. IEC 61000-4-2 (330 /150 pF) 3 4 5 6 VR (V) Fig. 3 - Typical Capacitance CD vs. Reverse Voltage VR 9 8 s to 100 % 100 % 8 7 80 % VR (V) 6 IPPM 60 % 20 s to 50 % BiAs-mode 5 4 40 % 3 2 20 % 1 0% 0 20548 10 20 30 Time (s) Fig. 2 - 8/20 s Peak Pulse Current Wave Form acc. IEC 61000-4-5 Rev. 1.2, 21-Jun-12 0 10-2 10-1 40 21793 1 101 102 103 104 105 IR (A) Fig. 4 - Typical Reverse Voltage VR vs. Reverse Current IR Document Number: 81149 2 For technical questions, contact: ESDprotection@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VCUT05B1-DD1 www.vishay.com Vishay Semiconductors 12 10 VC (V) 8 VC 6 4 Measured acc. IEC 61000-4-5 (8/20 s - wave form) 2 0 0 1 2 21794 3 4 5 IPP (A) Fig. 5 - Typical Peak Clamping Voltage VC vs. Peak Pulse Current IPP 60 Acc. IEC 61000-4-2 8 kV contact discharge 50 40 VC-ESD (V) 30 20 10 0 - 10 - 20 - 30 - 10 0 10 20 30 40 50 60 70 80 90 t (ns) 21795 Fig. 6 - Typical Clamping Performance at + 8 kV Contact Discharge (acc. IEC 61000-4-2) 250 Acc. IEC 61000-4-2 contact discharge VC-ESD (V) 200 150 100 VC-ESD 50 0 0 21796 5 10 15 20 25 30 VESD (kV) Fig. 7 - Typical Peak Clamping Voltage at ESD Contact Discharge (acc. IEC 61000-4-2) Rev. 1.2, 21-Jun-12 Document Number: 81149 3 For technical questions, contact: ESDprotection@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VCUT05B1-DD1 www.vishay.com Vishay Semiconductors 0.25 (0.010) 0.3 (0.012) 0.65 (0.026) 0.35 (0.014) 0.55 (0.022) 0 (0.000) Orientation Identification 0.125 (0.005) ref. 0.45 (0.018) 0.05 (0.002) 0.40 (0.016) 0.33 (0.013) 0.55 (0.022) 0.45 (0.018) 0.2 (0.008) 0.15 (0.006) PACKAGE DIMENSIONS in millimeters (inches): LLP1006-2M 1.05 (0.041) 0.95 (0.037) 0.05 (0.002) 0.25 (0.010) Document no.: S8-V-3906.04-019 (4) Created - Date: 24 June 2009 21798 1 (0.039) solder resist mask 0.2 (0.008) 0.5 (0.020) 0.6 (0.024) foot print recommendation: solder pad 0.5 (0.020) soldermask opening 0.03 measured middle of the package Unreeling direction Bidirectional LLP1006-xx Pin 1 mark Document no.: S8-V-3906.04-017 (4) Created - Date: 12. September 2007 22651 Rev. 1.2, 21-Jun-12 Top view Pad layout - view from top seen at bottom side Document Number: 81149 4 For technical questions, contact: ESDprotection@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000