OPA548 OPA 548 OPA 548 O PA 548 SBOS070B - OCTOBER 1997 - OCTOBER 2003 High-Voltage, High-Current OPERATIONAL AMPLIFIER FEATURES DESCRIPTION WIDE SUPPLY RANGE Single Supply: +8V to +60V Dual Supply: 4V to 30V HIGH OUTPUT CURRENT: 3A Continuous 5A Peak WIDE OUTPUT VOLTAGE SWING FULLY PROTECTED: Thermal Shutdown Adjustable Current Limit OUTPUT DISABLE CONTROL THERMAL SHUTDOWN INDICATOR HIGH SLEW RATE: 10V/s LOW QUIESCENT CURRENT PACKAGES: 7-Lead TO-220, Zip and Straight Leads 7-Lead DDPAK Surface-Mount The OPA548 is a low-cost, high-voltage/high-current operational amplifier ideal for driving a wide variety of loads. A laser-trimmed monolithic integrated circuit provides excellent low-level signal accuracy and high output voltage and current. The OPA548 operates from either single or dual supplies for design flexibility. In single-supply operation, the input common-mode range extends below ground. The OPA548 is internally protected against over-temperature conditions and current overloads. In addition, the OPA548 was designed to provide an accurate, user-selected current limit. Unlike other designs which use a "power" resistor in series with the output current path, the OPA548 senses the load indirectly. This allows the current limit to be adjusted from 0A to 5A with a resistor/potentiometer or controlled digitally with a voltage-out or current-out DAC. The Enable/Status (E/S) pin provides two functions. An input on the pin not only disables the output stage to effectively disconnect the load, but also reduces the quiescent current to conserve power. The E/S pin output can be monitored to determine if the OPA548 is in thermal shutdown. APPLICATIONS VALVE, ACTUATOR DRIVERS SYNCHRO, SERVO DRIVERS POWER SUPPLIES TEST EQUIPMENT TRANSDUCER EXCITATION AUDIO AMPLIFIERS The OPA548 is available in an industry-standard 7-lead staggered and straight lead TO-220 package, and a 7-lead DDPAK surface-mount plastic power package. The copper tab allows easy mounting to a heat sink or circuit board for excellent thermal performance. It is specified for operation over the extended industrial temperature range, -40C to +85C. A SPICE macromodel is available for design analysis. V+ - VIN OPA548 VO ILIM + VIN RCL (1/4W Resistor) RCL sets the current limit value from 0 to 5A. E/S V- Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright (c) 1997-2003, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. www.ti.com ABSOLUTE MAXIMUM RATINGS(1) ELECTROSTATIC DISCHARGE SENSITIVITY Output Current ................................................................. See SOA Curve Supply Voltage, V+ to V- ................................................................... 60V Input Voltage .................................................. (V-) - 0.5V to (V+) + 0.5V Input Shutdown Voltage ........................................................................ V+ Operating Temperature .................................................. -40C to +125C Storage Temperature ..................................................... -55C to +125C Junction Temperature ...................................................................... 150C Lead Temperature (soldering 10s)(2) .............................................. 300C This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. NOTES: (1) Stresses above these ratings may cause permanent damage. (2) Vapor-phase or IR reflow techniques are recommended for soldering the OPA547F surface-mount package. Wave soldering is not recommended due to excessive thermal shock and "shadowing" of nearby devices. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. PACKAGE/ORDERING INFORMATION For the most current package and ordering information, see the Package Ordering Addendum at the end of this data sheet. PIN CONFIGURATIONS Top Front View 7-Lead Stagger-Formed TO-220 (T) 7-Lead Straight-Formed TO-220 (T-1) 1 2 3 4 5 6 7 7-Lead DDPAK (FA) Surface-Mount 1 2 3 4 5 6 7 1 2 3 4 5 6 7 VIN+ ILIM V+ E/S VIN- V- VO VIN+ ILIM V+ E/S VIN- V- VO VIN+ ILIM V+ E/S VIN- V- VO NOTE: Tabs are electrically connected to the V- supply. 2 OPA548 www.ti.com SBOS070B ELECTRICAL CHARACTERISTICS At TCASE = +25C, VS = 30V and E/S pin open, unless otherwise noted. OPA548T, F PARAMETER OFFSET VOLTAGE Input Offset Voltage vs Temperature vs Power Supply INPUT BIAS CURRENT(1) Input Bias Current(2) vs Temperature Input Offset Current CONDITION MIN TYP MAX UNITS VCM = 0, IO = 0 TA = -40C to +85C VS = 4V to 30V 2 30 30 10 mV V/C V/V VCM = 0V TA = -40C to +85C VCM = 0V -100 0.5 5 -500 NOISE Input Voltage Noise Density, f = 1kHz Current Noise Density, f = 1kHz INPUT VOLTAGE RANGE Common-Mode Voltage Range: Positive Negative Common-Mode Rejection Linear Operation Linear Operation VCM = (V-) -0.1V to (V+) -3V (V+) - 3 (V-) - 0.1 80 INPUT IMPEDANCE Differential Common-Mode OPEN-LOOP GAIN Open-Loop Voltage Gain FREQUENCY RESPONSE Gain-Bandwidth Product Slew Rate Full-Power Bandwidth Settling Time: 0.1% Total Harmonic Distortion + Noise, f = 1kHz OUTPUT Voltage Output, Positive Negative Positive Negative Maximum Continuous Current Output: dc ac Leakage Current, Output Disabled, dc Output Current Limit Current Limit Range Current Limit Equation Current Limit Tolerance(1) VO = 25V, RL = 1k VO = 25V, RL = 8 90 RL = 8 G = 1, 50Vp-p, RL = 8 G = -10, 50V Step RL = 8, G = +3, Power = 10W IO = 3A IO = -3A IO = 0.6A IO = -0.6A (V+) - 4.1 (V-) + 3.7 (V+) - 2.4 (V-) + 1.3 3 3 POWER SUPPLY Specified Voltage Operating Voltage Range Quiescent Current Quiescent Current, Shutdown Mode TEMPERATURE RANGE Specified Range Operating Range Storage Range Thermal Resistance, JC 7-Lead DDPAK, 7-Lead TO-220 7-Lead DDPAK, 7-Lead TO-220 Thermal Resistance, JA 7-Lead DDPAK, 7-Lead TO-220 50 nA nA/C nA 90 200 nV/Hz fA/Hz (V+) - 2.3 (V-) - 0.2 95 V V dB 107 || 6 109 || 4 || pF || pF 98 90 dB dB 1 10 See Typical Characteristics 15 0.02(3) MHz V/s kHz s % (V+) - 3.7 (V-) + 3.3 (V+) - 2.1 (V-) + 1.0 V V V V A Arms See Typical Characteristics 0 to 5 ILIM = (15000)(4.75)/(13750 + RCL) 100 250 RCL = 14.8k (ILIM = 2.5A), RL = 8 A A mA See Typical Characteristics(4) Capacitive Load Drive OUTPUT ENABLE /STATUS (E/S) PIN Shutdown Input Mode VE/S HIGH (output enabled) VE/S LOW (output disabled) IE/S HIGH (output enabled) IE/S LOW (output disabled) Output Disable Time Output Enable Time Thermal Shutdown Status Output Normal Operation Thermally Shutdown Junction Temperature, Shutdown Reset from Shutdown 100 E/S Pin Open or Forced High E/S Pin Forced Low E/S Pin High E/S Pin Low (V-) + 2.4 Sourcing 20A Sinking 5A, TJ > 160C (V-) + 2.4 (V-) + 0.8 -65 -70 1 3 4 ILIM Connected to V-, IO = 0 ILIM Connected to V-, IO = 0 (V-) + 3.5 (V-) + 0.35 +160 +140 30 17 6 -40 -40 -55 (V-) + 0.8 V V A A s s V V C C 30 20 V V mA mA +85 +125 +125 C C C f > 50Hz dc 2 2.5 C/W C/W No Heat Sink 65 C/W NOTES: (1) High-speed test at TJ = +25C. (2) Positive conventional current flows into the input terminals. (3) See "Total Harmonic Distortion+Noise vs Frequency" in the Typical Characteristics section for additional power levels. (4) See "Small-Signal Overshoot vs Load Capacitance" in the Typical Characteristics section. OPA548 SBOS070B www.ti.com 3 TYPICAL CHARACTERISTICS At TCASE = +25C, VS = 30V and E/S pin open, unless otherwise noted. OPEN-LOOP GAIN AND PHASE vs FREQUENCY 100 RL = 8 60 -45 RL = 8 No Load -90 20 -135 0 -180 Input Bias Current (nA) G 40 -140 0 Phase () 80 Gain (dB) INPUT BIAS CURRENT vs TEMPERATURE -160 No Load -100 10 100 1k 10k 100k 1M VS = 30V -80 -60 -40 -75 -20 1 VS = 5V -120 10M -50 -25 0 CURRENT LIMIT vs TEMPERATURE 5 RCL = 14.7k 2 RCL = 57.6k 3 RCL = 57.6k 0 -50 -25 0 25 50 75 100 0 125 5 10 15 20 -200 Quiescent Current (mA) -150 -100 -50 VS = 5V 14 12 10 VS = 30V 8 IQ Shutdown VS = 5V 4 -10 0 10 30 VS = 30V IQ 16 6 -20 25 QUIESCENT CURRENT vs TEMPERATURE 18 Input Bias Current (nA) 20 Supply Voltage (V) INPUT BIAS CURRENT vs COMMON-MODE VOLTAGE 20 -75 30 -50 -25 0 25 50 75 100 125 Temperature (C) Common-Mode Voltage (V) 4 125 2 Temperature (C) 0 -30 100 RCL = 14.7k 1 1 0 -75 75 RCL = 4.02k 4 Current Limit (A) Current Limit (A) 3 50 CURRENT LIMIT vs SUPPLY VOLTAGE 5 +ILIM -ILIM RCL = 4.02k 4 25 Temperature (C) Frequency (Hz) OPA548 www.ti.com SBOS070B TYPICAL CHARACTERISTICS (Cont.) At TCASE = +25C, VS = 30V and E/S pin open, unless otherwise noted. POWER-SUPPLY REJECTION vs FREQUENCY COMMON-MODE REJECTION vs FREQUENCY 100 Power Supply Rejection (dB) 80 60 40 20 80 60 -PSRR 40 20 0 0 10 100 1k 10k 100k 10 1M 1k 10k 100k 1M Frequency (Hz) VOLTAGE NOISE DENSITY vs FREQUENCY OPEN-LOOP GAIN, COMMON-MODE REJECTION, AND POWER-SUPPLY REJECTION vs TEMPERATURE 100 110 AOL 400 95 AOL, PSRR (dB) Voltage Noise (nV/Hz) 100 Frequency (Hz) 500 300 200 105 90 100 PSRR 85 95 100 CMRR 80 -75 0 1 10 100 1k 10k 100k 1M -50 -25 0 25 50 75 100 Frequency (Hz) Temperature (C) GAIN-BANDWIDTH PRODUCT AND SLEW RATE vs TEMPERATURE TOTAL HARMONIC DISTORTION+NOISE vs FREQUENCY 1.25 13 G = +3 RL = 8 GBW 20W 12 0.75 11 SR+ 0.5 10 0.25 10W 0.1 THD+N (%) 1 90 125 1 Slew Rate (V/s) Gain-Bandwidth Product (MHz) +PSRR CMRR (dB) Common-Mode Rejection (dB) 100 0.1W 1W 0.01 9 SR- 0 -75 -50 -25 0 25 50 75 100 8 125 0.001 20 Temperature (C) 1k 10k 20k Frequency (Hz) OPA548 SBOS070B 100 www.ti.com 5 TYPICAL CHARACTERISTICS (Cont.) At TCASE = +25C, VS = 30V and E/S pin open, unless otherwise noted. OUTPUT VOLTAGE SWING vs TEMPERATURE 5 4 4 VSUPPLY - VOUT (V) VSUPPLY- VOUT (V) OUTPUT VOLTAGE SWING vs OUTPUT CURRENT 5 (V+) -VO 3 (V-) -VO 2 1 IO = +3A IO = -3A 3 2 IO = +0.6A 1 IO = -0.6A 0 0 0 1 2 3 -75 4 -25 0 25 OUTPUT LEAKAGE CURRENT vs APPLIED OUTPUT VOLTAGE 125 15 10 RCL = Leakage Current (mA) 20 RL = 8 5 RCL = 0 0 -5 Output Disabled VE/S < (V-) + 0.8V 0 1k 10k 100k -10 -40 1M -30 -20 -10 0 10 20 Frequency (Hz) Output Voltage (V) OFFSET VOLTAGE PRODUCTION DISTRIBUTION OFFSET VOLTAGE DRIFT PRODUCTION DISTRIBUTION 20 14 Typical distribution of packaged units. 16 14 12 10 8 6 4 30 40 Typical production distribution of packaged units. 12 Percent of Amplifiers (%) Percent of Amplifiers (%) 100 10 Maximum Output Voltage Without Slew Rate Induced Distortion 5 10 8 6 4 2 2 0 0 -10 -9 -8 -7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 6 7 8 9 10 Offset Voltage (mV) 6 75 MAXIMUM OUTPUT VOLTAGE SWING vs FREQUENCY 25 18 50 Temperature (C) 30 Output Voltage (Vp) -50 Output Current (A) 0 10 20 30 40 50 60 70 80 90 100 110 120 130 Offset Voltage Drift (V/C) OPA548 www.ti.com SBOS070B TYPICAL CHARACTERISTICS (Cont.) At TCASE = +25C, VS = 30V and E/S pin open, unless otherwise noted. LARGE-SIGNAL STEP RESPONSE G = 3, CL = 1000pF, RL = 8 SMALL-SIGNAL OVERSHOOT vs LOAD CAPACITANCE 50 G = +1 30 10V/div Overshoot (%) 40 20 G = -1 10 0 0 2k 4k 6k 8k 10k 12k 14k 16k 18k 20k 5s/div Load Capacitance (pF) SMALL-SIGNAL STEP RESPONSE G = 3, CL = 1000pF 50mV/div 100mV/div SMALL-SIGNAL STEP RESPONSE G = 1, CL = 1000pF 2s/div 2s/div OPA548 SBOS070B www.ti.com 7 APPLICATIONS INFORMATION Figure 1 shows the OPA548 connected as a basic noninverting amplifier. The OPA548 can be used in virtually any op amp configuration. Power-supply terminals should be bypassed with low series impedance capacitors. The technique shown in Figure 7, using a ceramic and tantalum type in parallel is recommended. In addition, we recommend a 0.01F capacitor between V+ and V- as close to the OPA548 as possible. Power-supply wiring should have low series impedance. V+ 10F + G = 1+ 0.1F(2) R1 R2 R1 2 VIN OPA548 6 3 1 ILIM(1) 4 (15000)(4.75) - 13750 (1) ILIM The low-level control signal (0A to 330A) also allows the current limit to be digitally controlled. See Figure 3 for a simplified schematic of the internal circuitry used to set the current limit. Leaving the ILIM pin open programs the output current to zero, while connecting ILIM directly to V- programs the maximum output current limit, typically 5A. Stress on the output transistors is determined both by the output current and by the output voltage across the conducting output transistor, VS - VO. The power dissipated by the output transistor is equal to the product of the output current and the voltage across the conducting transistor, VS - VO. The Safe Operating Area (SOA curve, Figure 2) shows the permissible range of voltage and current. E/S 7 R CL = SAFE OPERATING AREA R2 5 With the OPA548, the simplest method for adjusting the current limit uses a resistor or potentiometer connected between the ILIM pin and V- according to the Equation 1: VO ZL 0.1F(2) 0.01F(2) 10F + SAFE OPERATING AREA 10 Current-Limited V- Output Current (A) NOTES: (1) ILIM connected to V- gives the maximum current limit, 5A (peak). (2) Connect capacitors directly to package power-supply pins. FIGURE 1. Basic Circuit Connections. POWER SUPPLIES The OPA548 operates from single (+8V to +60V) or dual (4V to 30V) supplies with excellent performance. Most behavior remains unchanged throughout the full operating voltage range. Parameters which vary significantly with operating voltage are shown in the typical characteristic curves. Some applications do not require equal positive and negative output voltage swing. Power-supply voltages do not need to be equal. The OPA548 can operate with as little as 8V between the supplies and with up to 60V between the supplies. For example, the positive supply could be set to 55V with the negative supply at -5V, or vice-versa. ADJUSTABLE CURRENT LIMIT The OPA548 features an accurate, user-selected current limit. Current limit is set from 0A to 5A by controlling the input to the ILIM pin. Unlike other designs which use a power resistor in series with the output current path, the OPA548 senses the load indirectly. This allows the current limit to be set with a 0A to 330A control signal. In contrast, other designs require a limiting resistor to handle the full output current (5A in this case). 8 TC = 25C =5 PD 0W =2 6W PD Output current can be limited to less than 3A--see text. 1 PD =1 0W TC = 85C Pulse Operation Only T = 125C (Limit rms current to 3A) C 0.1 1 2 5 10 20 50 100 VS - VO (V) FIGURE 2. Safe Operating Area. The safe output current decreases as VS - VO increases. Output short-circuits are a very demanding case for SOA. A short-circuit to ground forces the full power-supply voltage (V+ or V-) across the conducting transistor. Increasing the case temperature reduces the safe output current that can be tolerated without activating the thermal shutdown circuit of the OPA548. For further insight on SOA, consult Application Bulletin SBOA022. AMPLIFIER MOUNTING Figure 4 provides recommended solder footprints for both the TO-220 and DDPAK power packages. The tab of both packages is electrically connected to the negative supply, V-. It may be desirable to isolate the tab of the TO-220 package from its OPA548 www.ti.com SBOS070B RESISTOR METHOD DAC METHOD (Current or Voltage) Max IO = ILIM ILIM = 13750 4.75V (4.75) (15000) Max IO = ILIM 13750 + RCL ILIM =15000 ISET 3 3 RCL 4 D/A 0.01F (optional, for noisy environments) 4 V- V- RCL = 15000 (4.75V) ILIM 13750 4.75V ISET ISET = ILIM /15000 - 13750 VSET = (V-) + 4.75V - (13750) (ILIM)/15000 OPA547 CURRENT LIMIT: 0 to 5A DESIRED CURRENT LIMIT RESISTOR(1) (RCL) CURRENT (ISET) VOLTAGE (VSET) 0A 1A 2.5A 3A 4A 5A ILIM Open 57.6k 14.7k 10k 4.02k ILIM Connected to V- 0A 67A 167A 200A 267A 333A (V-) + 4.75V (V-) + 3.8V (V-) + 2.5V (V-) + 2V (V-) + 1.1V (V-) NOTE: (1) Resistors are nearest standard 1% values. FIGURE 3. Adjustable Current Limit. DDPAK-7(1) (Package Designator KTW) TO220-7 (Package Designator KVT) 0.45 0.04 0.2 0.05 0.085 0.15 0.335 0.51 0.05 0.035 0.105 Mean dimensions in inches. Refer to end of data sheet or www.ti.com for tolerances and detailed package drawings. NOTE: (1) For improved thermal performance increase footprint area. See Figure 6, "Thermal Resistance vs Circuit Board Copper Area". FIGURE 4. TO-220 and DDPAK Solder Footprints. mounting surface with a mica (or other film) insulator (see Figure 5). For lowest overall thermal resistance it is best to isolate the entire heat sink/OPA548 structure from the mounting surface rather than to use an insulator between the semiconductor and heat sink. For best thermal performance, the tab of the DDPAK surface-mount version should be soldered directly to a circuit board copper area. Increasing the copper area improves heat dissipation. See Figure 6 for typical thermal resistance from junction-to-ambient as a function of the copper area. POWER DISSIPATION Power dissipation depends on power supply, signal, and load conditions. For dc signals, power dissipation is equal to the product of output current times the voltage across the OPA548 SBOS070B www.ti.com 9 THERMAL RESISTANCE vs ALUMINUM PLATE AREA Aluminum Plate Area Thermal Resistance JA (C/W) 18 Vertically Mounted in Free Air Flat, Rectangular Aluminum Plate 16 14 0.030in Al 12 0.050in Al 10 Aluminum Plate Thickness 0.062in Al 8 0 1 2 3 4 5 6 7 Optional mica or film insulator for electrical isolation. Adds OPA548 approximately 1C/W. TO220 Package 8 Aluminum Plate Area (inches2) FIGURE 5. TO-220 Thermal Resistance vs Aluminum Plate Area. THERMAL RESISTANCE vs CIRCUIT BOARD COPPER AREA Thermal Resistance, JA (C/W) 50 Circuit Board Copper Area OPA548F Surface Mount Package 1oz copper 40 30 20 10 0 0 1 2 3 4 OPA548 Surface-Mount Package 5 Copper Area (inches2) FIGURE 6. DDPAK Thermal Resistance vs Circuit Board Copper Area. conducting output transistor. Power dissipation can be minimized by using the lowest possible power-supply voltage necessary to assure the required output voltage swing. For resistive loads, the maximum power dissipation occurs at a dc output voltage of one-half the power-supply voltage. Dissipation with ac signals is lower. Application Bulletin SBOA022 explains how to calculate or measure power dissipation with unusual signals and loads. THERMAL PROTECTION Power dissipated in the OPA548 will cause the junction temperature to rise. The OPA548 has thermal shutdown circuitry that protects the amplifier from damage. The thermal protection circuitry disables the output when the junction temperature reaches approximately 160C, allowing the device to cool. When the junction temperature cools to approximately 140C, the output circuitry is again enabled. Depending on load and signal conditions, the thermal protection 10 circuit may cycle on and off. This limits the dissipation of the amplifier but may have an undesirable effect on the load. Any tendency to activate the thermal protection circuit indicates excessive power dissipation or an inadequate heat sink. For reliable operation, junction temperature should be limited to 125C, maximum. To estimate the margin of safety in a complete design (including heat sink) increase the ambient temperature until the thermal protection is triggered. Use worst-case load and signal conditions. For good reliability, thermal protection should trigger more than 35C above the maximum expected ambient condition of your application. This produces a junction temperature of 125C at the maximum expected ambient condition. The internal protection circuitry of the OPA548 was designed to protect against overload conditions. It was not intended to replace proper heat sinking. Continuously running the OPA548 into thermal shutdown will degrade reliability. OPA548 www.ti.com SBOS070B HEAT SINKING Combining equations (1) and (2) gives: Most applications require a heat sink to assure that the maximum operating junction temperature (125C) is not exceeded. In addition, the junction temperature should be kept as low as possible for increased reliability. Junction temperature can be determined according to the equation: TJ = TA + PDJA (1) where, JA = JC + CH + HA (2) TJ = Junction Temperature (C) TA = Ambient Temperature (C) PD = Power Dissipated (W) JC = Junction-to-Case Thermal Resistance (C/W) CH = Case-to-Heat Sink Thermal Resistance (C/W) HA = Heat Sink-to-Ambient Thermal Resistance (C/W) JA = Junction-to-Air Thermal Resistance (C/W) Figure 7 shows maximum power dissipation versus ambient temperature with and without the use of a heat sink. Using a heat sink significantly increases the maximum power dissipation at a given ambient temperature as shown. The difficulty in selecting the heat sink required lies in determining the power dissipated by the OPA548. For dc output into a purely resistive load, power dissipation is simply the load current times the voltage developed across the conducting output transistor, PD = IL(VS-VO). Other loads are not as simple. Consult Application Bulletin SBOA022 for further insight on calculating power dissipation. Once power dissipation for an application is known, the proper heat sink can be selected. Power Dissipation (Watts) TO220 with Thermalloy 6030B Heat Sink JA = 16.7C/W 8 PD = (TJ (max) - TA) / JA TJ (max) = 150C 2 DDPAK or TO-220 JA = 65C/W (no heat sink) 0 0 25 50 HA = TJ - TA - ( JC + CH ) PD HA = 125C - 40C - (2.5C / W + 1C / W ) = 13.5C / W 5W To maintain junction temperature below 125C, the heat sink selected must have a HA less than 14C/W. In other words, the heat sink temperature rise above ambient must be less than 67.5C (13.5C/W * 5W). For example, at 5W Thermalloy model number 6030B has a heat sink temperature rise of 66C above ambient (HA = 66C/5W = 13.2C/W), which is below the 67.5C required in this example. Figure 7 shows power dissipation versus ambient temperature for a TO-220 package with a 6030B heat sink. Another variable to consider is natural convection versus forced convection air flow. Forced-air cooling by a small fan can lower CA (CH + HA) dramatically. Heat sink manufactures provide thermal data for both of these cases. For additional information on determining heat sink requirements, consult Application Bulletin SBOA021. The Enable/Status pin provides two functions: forcing this pin LOW disables the output stage, or E/S can be monitored to determine if the OPA548 is in thermal shutdown. One or both of these functions can be utilized on the same device using single or dual supplies. For normal operation (output enabled), the E/S pin can be left open or pulled HIGH (at least 2.4V above the negative rail). A small value capacitor connected between the E/S pin and V- may be required for noisy applications. DDPAK JA = 26C/W (3 in2 one oz copper mounting pad) 4 TJ, TA, and PD are given. JC is provided in the specification table, 2.5C/W (dc). CH can be obtained from the heat sink manufacturer. Its value depends on heat sink size, area, and material used. Semiconductor package type, mounting screw torque, insulating material used (if any), and thermal joint compound used (if any) also affect CH. A typical CH for a TO-220 mounted package is 1C/W. Now we can solve for HA: ENABLE/STATUS (E/S) PIN With infinite heat sink ( JA = 2.5C/W), max PD = 50W at TA = 25C. 6 (3) As mentioned earlier, once a heat sink has been selected, the complete design should be tested under worst-case load and signal conditions to ensure proper thermal protection. MAXIMUM POWER DISSIPATION vs AMBIENT TEMPERATURE 10 TJ = TA + PD(JC + CH + HA) 75 100 125 Ambient Temperature (C) Output Disable FIGURE 7. Maximum Power Dissipation vs Ambient Temperature. Heat Sink Selection Example A TO-220 package is dissipating 5W. The maximum expected ambient temperature is 40C. Find the proper heat sink to keep the junction temperature below 125C (150C minus 25C safety margin). A unique feature of the OPA548 is its output disable capability. This function not only conserves power during idle periods (quiescent current drops to approximately 6mA), but also allows multiplexing in low frequency (f < 20kHz), multichannel applications. Signals greater than 20kHz may cause leakage current to increase in devices that are shutdown. Figure 18 shows the two OPA548s in a switched amplifier configuration. The on/off state of the two amplifiers is controlled by the voltage on the E/S pin. OPA548 SBOS070B www.ti.com 11 To disable the output, the E/S pin is pulled LOW, no greater than 0.8V above the negative rail. Typically the output is shutdown in 1s. Figure 8 provides an example of how to implement this function using a single supply. Figure 9 gives a circuit for dual-supply applications. To return the output to an enabled state, the E/S pin should be disconnected (open) or pulled to at least (V-) + 2.4V. It should be noted that pulling the E/S pin HIGH (output enabled) does not disable internal thermal shutdown. V+ 5V OPA548 2.49k E/S TTL V- Zetex ZVN3310 OR HCT V+ FIGURE 10. Thermal Shutdown Status with a Single Supply. OPA548 E/S 5V V+ V- CMOS or TTL 1k OPA548 FIGURE 8. Output Disable with a Single Supply. 2N3906 E/S 22k 470 Zetex ZVN3310 V+ V- 5V FIGURE 11. Thermal Shutdown Status with Dual Supplies. OPA548 E/S 1 (1) 6 Output Disable and Thermal Shutdown Status 5 As mentioned earlier, the OPA548's output can be disabled and the disable status can be monitored simultaneously. Figures 12 and 13 provide examples interfacing to the E/S pin while using a single supply and dual supplies, respectively. 1 4 HCT or TTL In 4N38 V- Optocoupler OUTPUT STAGE COMPENSATION NOTE: (1) Optional--may be required to limit leakage current of optocoupler at high temperatures. FIGURE 9. Output Disable with Dual Supplies. Thermal Shutdown Status Internal thermal shutdown circuitry shuts down the output when the die temperature reaches approximately 160C, resetting when the die has cooled to 140C. The E/S pin can be monitored to determine if shutdown has occurred. During normal operation the voltage on the E/S pin is typically 3.5V above the negative rail. Once shutdown has occurred, this voltage drops to approximately 350mV above the negative rail. Figure 10 gives an example of monitoring shutdown in a single-supply application. Figure 11 provides a circuit for dual supplies. External logic circuitry or an LED could be used to indicate if the output has been thermally shutdown, see Figure 16. 12 The complex load impedances common in power op amp applications can cause output stage instability. For normal operation output compensation circuitry is typically not required. However, if the OPA548 is intended to be driven into current limit, an R/C network may be required. See Figure 14 for an output series R/C compensation (snubber) network which generally provides excellent stability. A snubber circuit may also enhance stability when driving large capacitive loads (> 1000pF) or inductive loads (motors, loads separated from the amplifier by long cables). Typically 3 to 10 in series with 0.01F to 0.1F is adequate. Some variations in circuit value may be required with certain loads. OUTPUT PROTECTION Reactive and EMF-generating loads can return load current to the amplifier, causing the output voltage to exceed the power-supply voltage. This damaging condition can be OPA548 www.ti.com SBOS070B V+ V+ R1 5k R2 20k R2 = -4 R1 G=- VIN OPA548 D1 E/S OPA548 V- Open Drain (Output Disable) 10 (Carbon) Motor D2 HCT (Thermal Status Shutdown) 0.01F V- D1, D2 : Motorola MUR410. FIGURE 12. Output Disable and Thermal Shutdown Status with a Single Supply. FIGURE 14. Motor Drive Circuit. V+ 5V 1 6 5V OPA548 E/S 5 7.5k 1W 1 6 2 (1) Zetex ZVN3310 5 TTL Out 4 4N38 Optocoupler HCT or TTL In 2 4 4N38 Optocoupler V- NOTE: (1) Optional--may be required to limit leakage current of optocoupler at high temperatures. FIGURE 13. Output Disable and Thermal Shutdown Status with Dual Supplies. avoided with clamp diodes from the output terminal to the power supplies, as shown in Figure 14. Schottky rectifier diodes with a 5A or greater continuous rating are recommended. used as a voltage reference, thus eliminating the need for an external reference. The feedback resistors are selected to gain VCL to the desired output voltage level. PROGRAMMABLE POWER SUPPLY VOLTAGE SOURCE APPLICATION Figure 15 illustrates how to use the OPA548 to provide an accurate voltage source with only three external resistors. First, the current limit resistor, RCL, is chosen according to the desired output current. The resulting voltage at the ILIM pin is constant and stable over temperature. This voltage, VCL, is connected to the noninverting input of the op amp and A programmable source/sink power supply can easily be built using the OPA548. Both the output voltage and output current are user-controlled. See Figure 16 for a circuit using potentiometers to adjust the output voltage and current while Figure 17 uses DACs. An LED tied to the E/S pin through a logic gate indicates if the OPA548 is in thermal shutdown. OPA548 SBOS070B www.ti.com 13 R1 R2 V+ VO = VCL (1 + R2/R1) 4.75V 13750 V- IO = VCL 15000 (4.75V) 13750 + RCL ILIM For Example: RCL 0.01F (Optional, for noisy environments) If ILIM = 3A, RCL = 10k VCL = 10k * 4.75V = 2V (10k + 13750) Desired VO = 20V, G = 20 2 Uses voltage developed at ILIM pin as a moderately accurate reference voltage. = 10 R1 = 1k and R2 = 9k FIGURE 15. Voltage Source. 1k 9k G=1+ +5V 9k = 10 1k +30V 10.5k 5 2 V+ 6 Output Adjust 10k 0.12V to 2.5V VO = 1.2V to 25V(1) IO = 0 to 5A OPA548 1 4 3 7 E/S 74HCT04 ILIM R 250 499 V- +5V V- 0V to 4.75V Thermal Shutdown Status (LED) 1k Current Limit Adjust 20k 0.01F(2) NOTES: (1) For VO 0V, V- -1V. (2) Optional: Improves noise immunity. FIGURE 16. Resistor-Controlled Programmable Power Supply. 14 OPA548 www.ti.com SBOS070B 1k 9k -5V OUTPUT ADJUST VREF +30V G = 10 +5V VREF A +5V RFB A 1/2 OPA2336 IOUT A 1/2 DAC7800/1/2(3) VO = 0.8 to 25V(1) OPA548 10pF 74HCT04 E/S DAC A AGND A ILIM IO = 0 to 5A R 250 V- Thermal Shutdown Status (LED) VREF B RFB B 10pF 1/2 OPA2336 IOUT B 1/2 DAC7800/1/2(3) DAC B 0.01F(2) DGND AGND B CURRENT LIMIT ADJUST NOTES: (1) For VO 0V, V- -1V. (2) Optional, improves noise immunity. (3) Chose DAC780X based on digital interface: DAC7800--12-bit interface, DAC7801--8-bit interface + 4 bits, DAC7802--serial interface. FIGURE 17. Digitally-Controlled Programmable Power Supply. R1 R2 VIN1 OPA548 ILIM AMP1 E/S RCL2 RCL1 R3 VE/S R4 Close for high current (Could be open drain output of a logic gate). VO VIN2 V- AMP2 E/S FIGURE 19. Multiple Current Limit Values. VE/S > (V-) +2.4V: Amp 1 is on, Amp 2 if off VO = -VIN1 OPA548 R2 ( ) R1 ILIM VE/S < (V-) +2.4V: Amp 2 is on, Amp 1 if off VO = -VIN2 R4 ( ) VO As VO increases, ILIM decreases. RCL R3 FIGURE 18. Switched Amplifier. FIGURE 20. Single Quadrant V * I Limiting. OPA548 SBOS070B www.ti.com 15 R2 4k R1 1k V+ 0.25 800 G= 1 + 4k 1k = 5(1) OPA548 ILIM V- VO IO = 10A (peak)(2) VIN V+ 800 0.25 OPA548 ILIM V- R3 1k R4 4k NOTES: (1) Works well for G < 10. Input offset causes output current to flow between amplifiers with G > 10. Gains (resistor ratios) of the two amplifiers should be carefully matched to ensure equal current sharing. (2) As configured (ILIM connected to V-) output current limit is set to 10A (peak). Each amplifier is limited to 5A (peak). Other current limit values may be obtained, see Figure 3, "Adjustable Current Limit". FIGURE 21. Parallel Output for Increased Output Current. 16 OPA548 www.ti.com SBOS070B PACKAGE OPTION ADDENDUM www.ti.com 18-Sep-2008 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty Lead/Ball Finish MSL Peak Temp (3) OPA548F OBSOLETE DDPAK KTW 7 TBD Call TI Call TI OPA548F/500 ACTIVE DDPAK KTW 7 500 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR OPA548F/500G3 ACTIVE DDPAK KTW 7 500 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR OPA548FKTWT ACTIVE DDPAK KTW 7 50 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR OPA548FKTWTG3 ACTIVE DDPAK KTW 7 50 Green (RoHS & no Sb/Br) CU SN Level-2-260C-1 YEAR OPA548T ACTIVE TO-220 KVT 7 50 Green (RoHS & no Sb/Br) CU SN N / A for Pkg Type OPA548T-1 ACTIVE TO-220 KC 7 50 Green (RoHS & no Sb/Br) CU SN N / A for Pkg Type OPA548T-1G3 ACTIVE TO-220 KC 7 50 Green (RoHS & no Sb/Br) CU SN N / A for Pkg Type OPA548TG3 ACTIVE TO-220 KVT 7 50 Green (RoHS & no Sb/Br) CU SN N / A for Pkg Type (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device OPA548FKTWT Package Package Pins Type Drawing DDPAK KTW 7 SPQ 50 Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 330.0 24.4 Pack Materials-Page 1 10.6 B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 15.6 4.9 16.0 24.0 Q2 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) OPA548FKTWT DDPAK KTW 7 50 367.0 367.0 45.0 Pack Materials-Page 2 MECHANICAL DATA MPSF015 - AUGUST 2001 KTW (R-PSFM-G7) PLASTIC FLANGE-MOUNT 0.410 (10,41) 0.385 (9,78) 0.304 (7,72) -A- 0.006 -B- 0.303 (7,70) 0.297 (7,54) 0.0625 (1,587) H 0.055 (1,40) 0.0585 (1,485) 0.300 (7,62) 0.064 (1,63) 0.045 (1,14) 0.252 (6,40) 0.056 (1,42) 0.187 (4,75) 0.370 (9,40) 0.179 (4,55) 0.330 (8,38) H 0.296 (7,52) A 0.605 (15,37) 0.595 (15,11) 0.012 (0,305) C 0.000 (0,00) 0.019 (0,48) 0.104 (2,64) 0.096 (2,44) H 0.017 (0,43) 0.050 (1,27) C C F 0.034 (0,86) 0.022 (0,57) 0.010 (0,25) M B 0.026 (0,66) 0.014 (0,36) 0~3 AM C M 0.183 (4,65) 0.170 (4,32) 4201284/A 08/01 NOTES: A. All linear dimensions are in inches (millimeters). B. This drawing is subject to change without notice. C. Lead width and height dimensions apply to the plated lead. D. Leads are not allowed above the Datum B. E. Stand-off height is measured from lead tip with reference to Datum B. F. Lead width dimension does not include dambar protrusion. Allowable dambar protrusion shall not cause the lead width to exceed the maximum dimension by more than 0.003". G. Cross-hatch indicates exposed metal surface. H. Falls within JEDEC MO-169 with the exception of the dimensions indicated. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 MECHANICAL DATA MSOT010 - OCTOBER 1994 KC (R-PSFM-T7) PLASTIC FLANGE-MOUNT PACKAGE 0.156 (3,96) 0.146 (3,71) 0.420 (10,67) 0.380 (9,65) DIA 0.113 (2,87) 0.103 (2,62) 0.185 (4,70) 0.175 (4,46) 0.055 (1,40) 0.045 (1,14) 0.147 (3,73) 0.137 (3,48) 0.335 (8,51) 0.325 (8,25) 1.020 (25,91) 1.000 (25,40) 1 7 0.125 (3,18) (see Note C) 0.030 (0,76) 0.026 (0,66) 0.010 (0,25) M 0.050 (1,27) 0.300 (7,62) 0.122 (3,10) 0.102 (2,59) 0.025 (0,64) 0.012 (0,30) 4040251 / B 01/95 NOTES: A. B. C. D. E. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. Lead dimensions are not controlled within this area. All lead dimensions apply before solder dip. The center lead is in electrical contact with the mounting tab. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated