TSL267 High-Sensitivity IR Light-to-Voltage Converter General Description The TSL267 is a high-sensitivity low-noise infrared light-to-voltage converter that combines a photodiode and a transimpedance amplifier on a single monolithic CMOS integrated circuit. Output voltage is directly proportional to IR light intensity (irradiance) on the photodiode. The TSL267 has a transimpedance gain of 320 M. The device has improved offset voltage stability and low power consumption and is supplied in a 3-lead visible-light-blocking plastic sidelooker package with an integral lens. Ordering Information and Content Guide appear at end of datasheet. Key Benefits & Features The benefits and features of TSL267, High-Sensitivity IR Light-to-Voltage Converter are listed below: Figure 1: Added Value Of Using TSL267 Benefits Features * Enables Extremely Fast Response to Change * Single Photo-Diode and Trans Impedance Architecture * Enables Fast Response to Visible Light in Range of 400nm to 700nm Wavelengths * 160s Output Rise-Time Response * Provides for High Sensitivity to Detect a Small Change in Light * High Irradiance Responsivity 0.45V/(W/cm2) at p = 940nm * Provides Additional Sensitivity Advantages * 2x Gain Lens * Provides Full Dynamic Range * Rail-to-Rail Output Swing * Integral Visible Light Cut-OFF Filter * Converts IR Light Intensity to Output Voltage * Monolithic Silicon IC Containing Photodiode, Operational Amplifier, and Feedback Components * High Sensitivity * Single Voltage Supply Operation (2.7 V to 5.5 V) * Low Noise (200 Vrms Typ to 1 kHz) * High Power-Supply Rejection (35 dB at 1 kHz) * Compact 3-Leaded Plastic Package * RoHS Compliant (-LF Package Only) ams Datasheet [v1-00] 2016-Jul-11 Page 1 Document Feedback TSL267 - General Description Block Diagram The functional blocks of this device are shown below: Figure 2: TSL267 Block Diagram - + Page 2 Document Feedback Voltage Output ams Datasheet [v1-00] 2016-Jul-11 TSL267 - Pin Assignments Pin Assignments Figure 3: Package S Sidelooker (Front View) 1 GND 2 VDD 3 OUT Figure 4: Package SM Surface Mount Sidelooker (Front View) 1 GND 2 VDD 3 OUT Figure 5: Terminal Functions Terminal Description Name No GND 1 Ground (substrate). All voltages are referenced to GND. OUT 3 Output voltage VDD 2 Supply voltage ams Datasheet [v1-00] 2016-Jul-11 Page 3 Document Feedback TSL267 - Absolute Maximum Ratings Absolute Maximum Ratings Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. Figure 6: Absolute Maximum Ratings Over Operating Free-Air Temperature Range (unless otherwise noted) Symbol Parameter Min Supply voltage (1) VDD Output current IO Duration of short-circuit current at (or below) 25C TA TSTRG Max Units 6 V 10 mA 5 s Operating free-air temperature range -25 85 C Storage temperature range -25 85 C Lead temperature 1.6 mm (1/16 inch) from case for 10 seconds (S Package) 260 C Reflow solder, in accordance with J-STD-020C or J-STD-020D (SM Package) 260 C Note(s): 1. All voltages are with respect to GND. Figure 7: Recommended Operating Conditions Symbol VDD TA Parameter Supply voltage Operating free-air temperature Page 4 Document Feedback Min Nom Max Units 2.7 5.5 V 0 70 C ams Datasheet [v1-00] 2016-Jul-11 TSL267 - Electrical Characteristics Electrical Characteristics Electrical Characteristics at V DD = 5 V, TA = 25C, p = 940 nm, R L = 10k (unless otherwise noted) see notes (1), (2), (3). Figure 8: Electrical Characteristics Symbol VD VOM Parameter Dark voltage Maximum output voltage swing Test Conditions Ee = 0 Min Typ 0 VDD = 4.5 V, no load Max Unit 15 mV 4.49 V VDD = 4.5 V, RL = 10k 4 4.2 1.2 2 VO Output voltage Ee = 4.4 W/cm2 VD Temperature coefficient of dark voltage (VD) TA = 0C to 70C -15 V/C Ne Irradiance responsivity See note (4) 0.45 V/(W/cm2) fac = 100 Hz (5) 55 dB PSRR Power supply rejection ratio fac = 1 kHz (5) 35 dB Ee = 4.4 W/cm2 1.9 IDD Supply current 2.8 4 V mA Note(s): 1. Measurements are made with RL = 10 k between output and ground. 2. Optical measurements are made using small-angle incident radiation from an LED optical source. 3. The input irradiance is supplied by a GaAs light-emitting diode with the following characteristics: peak wavelength p = 940 nm. 4. Irradiance responsivity is characterized over the range V O = 0.1 to 4.5 V. The best-fit straight line of Output Voltage V O versus irradiance Ee over this range will typically have a positive extrapolated V O value for Ee = 0. 5. Power supply rejection ratio PSRR is defined as 20 log (VDD (f )/V O(f )) with V DD(f = 0) = 5 V and V O(f = 0) = 2 V. ams Datasheet [v1-00] 2016-Jul-11 Page 5 Document Feedback TSL267 - Electrical Characteristics Figure 9: Switching Characteristics at VDD = 5V, TA = 25C , p = 940 nm, RL = 10k (unless otherwise noted) Symbol Parameter Test Conditions Min Typ Max Unit tr Output pulse rise time, 10% to 90% of final value See note (1) and Figure 10 160 250 s tf Output pulse fall time, 10% to 90% of final value See note (1) and Figure 10 150 250 s ts Output settling time, 1% of final value See note (1) and Figure 10 330 s Integrated noise voltage f = dc to 1 kHz, Ee = 0 200 Vrms Vn Output noise voltage, rms f = 10 Hz, Ee = 0 6 f = 100 Hz, Ee = 0 6 f = 1 kHz, Ee = 0 7 V/Hz rms Note(s): 1. Switching characteristics apply over the range V O = 0.1 V to 4.5 V. Page 6 Document Feedback ams Datasheet [v1-00] 2016-Jul-11 TSL267 - Parameter Measurement Information Parameter Measurement Information Figure 10: Switching Times VDD Pulse Generator Ee 2 Input LED (see Note ) 3 tf tr Output + 1 TEST CIRCUIT 90% RL TSL267 Output (see Note) 10% 90% 10% VOLTAGE WAVEFORM Note(s): 1. The input irradiance is supplied by a pulsed GaAs light-emitting diode with the following characteristics: p = 940 nm, tr < 1s, t f < 1s. 2. The output waveform is monitored on an oscilloscope with the following characteristics: t r < 100 ns, Z i 1 M, Ci 20 pF. ams Datasheet [v1-00] 2016-Jul-11 Page 7 Document Feedback TSL267 - Typical Operating Characteristics Typical Operating Characteristics Figure 11: Photodiode Spectral Responsivity 1.6 TA = 25qC 1.4 Normalized to 940 nm Relative Responsivity 1.2 1.0 0.8 0.6 0.4 0.2 0 700 800 900 1000 O Wavelength nm 1100 Figure 12: Power Supply Rejection Ratio vs Frequency Power Supply Rejection Ratio -- dB 80 70 60 50 40 30 20 10 0 10 Page 8 Document Feedback 102 103 104 f Frequency Hz 105 106 ams Datasheet [v1-00] 2016-Jul-11 TSL267 - Typical Operating Characteristics Figure 13: Dark Voltage vs Free-Air Temperature 10 VDD = 5 V 9 V D Dark Voltage mV 8 7 6 5 4 3 2 1 0 0 10 20 40 60 30 50 TA Free-Air Temperature qC 70 Figure 14: Normalized Response vs Angular Displacement 1.0 0.9 Normalized Response 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 90 ams Datasheet [v1-00] 2016-Jul-11 70 50 30 10 10 30 50 Angular Displacement 5 70 90 Page 9 Document Feedback TSL267 - Application Information Application Information PCB Pad Layout Suggested PCB pad layout guidelines for the SM surface mount package are shown in Figure 15. Figure 15: Suggested SM Package PCB Layout 1.0 1.0 1.0 3.2 1.0 1.0 Note(s): 1. All linear dimensions are in millimeters. 2. This drawing is subject to change without notice. Page 10 Document Feedback ams Datasheet [v1-00] 2016-Jul-11 TSL267 - Package Mechanical Data The device is supplied in a visible light-blocking plastic three-lead through-hole sidelooker package (S). Package Mechanical Data Figure 16: Package S -- Single-In-Line Side-Looker Package Configuration TOP VIEW 4.60 RoHS 2.60 R 0.90 Green 1.64 FRONT VIEW SIDE VIEW 2.30 0.15 Note 1.80 4.60 1 1.56 0.42 14.86 + 0.50 Pb 2y2 0.47 TYP Lead Free Available 0.42 Note(s): 1. All linear dimensions are in millimeters; tolerance is 0.25 mm unless otherwise stated. 2. Dimension is to center of lens arc, which is located below the package face. 3. The integrated photodiode active area is round with a typical diameter of 0.75 mm and is typically located in the center of the lens and 0.97 mm below the top of the lens surface. 4. Lead finish for TSL267-LF: solder dipped, 100% Sn. 5. This drawing is subject to change without notice. ams Datasheet [v1-00] 2016-Jul-11 Page 11 Document Feedback TSL267 - Package Mechanical Data Figure 17: Package SM -- Surface Mount Side-Looker Package Configuration TOP VIEW 4.60 RoHS Green 2.60 R 0.90 1.64 FRONT VIEW SIDE VIEW 0.15 Note 2.30 1.80 4.60 0.62 + 0.10 1.97 2.59 1.00 0.42 0.62 +0.10 i0.15 5.73 + 0.50 Pb 2y2 0.47 TYP Lead Free 0.42 Note(s): 1. All linear dimensions are in millimeters; tolerance is 0.25 mm unless otherwise stated. 2. Dimension is to center of lens arc, which is located below the package face. 3. The integrated photodiode active area is typically located in the center of the lens and 0.97 mm below the top of the lens surface. 4. Index of refraction of clear plastic is 1.55. 5. Lead finish for TSL267SM-LF: solder dipped, 100% Sn. 6. This drawing is subject to change without notice. Page 12 Document Feedback ams Datasheet [v1-00] 2016-Jul-11 TSL267 - Ordering & Contact Information Ordering & Contact Information Figure 18: Ordering Information Ordering Code Device TA TSL267-LF TSL267 0C to 70C 3-lead Sidelooker - Lead (Pb) Free TSL267SM-LF TSL267 0C to 70C 3-lead Surface - Mount Sidelooker Lead (Pb) Free Package - Leads Package Designator S SM Buy our products or get free samples online at: www.ams.com/ICdirect Technical Support is available at: www.ams.com/Technical-Support Provide feedback about this document at: www.ams.com/Document-Feedback For further information and requests, e-mail us at: ams_sales@ams.com For sales offices, distributors and representatives, please visit: www.ams.com/contact Headquarters ams AG Tobelbaderstrasse 30 8141 Premstaetten Austria, Europe Tel: +43 (0) 3136 500 0 Website: www.ams.com ams Datasheet [v1-00] 2016-Jul-11 Page 13 Document Feedback TSL267 - RoHS Compliant & ams Green Statement RoHS Compliant & ams Green Statement RoHS: The term RoHS compliant means that ams AG products fully comply with current RoHS directives. Our semiconductor products do not contain any chemicals for all 6 substance categories, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, RoHS compliant products are suitable for use in specified lead-free processes. ams Green (RoHS compliant and no Sb/Br): ams Green defines that in addition to RoHS compliance, our products are free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material). Important Information: The information provided in this statement represents ams AG knowledge and belief as of the date that it is provided. ams AG bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. ams AG has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. ams AG and ams AG suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. Page 14 Document Feedback ams Datasheet [v1-00] 2016-Jul-11 TSL267 - Copyrights & Disclaimer Copyrights & Disclaimer Copyright ams AG, Tobelbader Strasse 30, 8141 Premstaetten, Austria-Europe. Trademarks Registered. All rights reserved. The material herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. Devices sold by ams AG are covered by the warranty and patent indemnification provisions appearing in its General Terms of Trade. ams AG makes no warranty, express, statutory, implied, or by description regarding the information set forth herein. ams AG reserves the right to change specifications and prices at any time and without notice. Therefore, prior to designing this product into a system, it is necessary to check with ams AG for current information. This product is intended for use in commercial applications. Applications requiring extended temperature range, unusual environmental requirements, or high reliability applications, such as military, medical life-support or life-sustaining equipment are specifically not recommended without additional processing by ams AG for each application. This product is provided by ams AG "AS IS" and any express or implied warranties, including, but not limited to the implied warranties of merchantability and fitness for a particular purpose are disclaimed. ams AG shall not be liable to recipient or any third party for any damages, including but not limited to personal injury, property damage, loss of profits, loss of use, interruption of business or indirect, special, incidental or consequential damages, of any kind, in connection with or arising out of the furnishing, performance or use of the technical data herein. No obligation or liability to recipient or any third party shall arise or flow out of ams AG rendering of technical or other services. ams Datasheet [v1-00] 2016-Jul-11 Page 15 Document Feedback Document Status Document Status Product Preview Preliminary Datasheet Datasheet Datasheet (discontinued) Page 16 Document Feedback Product Status Definition Pre-Development Information in this datasheet is based on product ideas in the planning phase of development. All specifications are design goals without any warranty and are subject to change without notice Pre-Production Information in this datasheet is based on products in the design, validation or qualification phase of development. The performance and parameters shown in this document are preliminary without any warranty and are subject to change without notice Production Information in this datasheet is based on products in ramp-up to full production or full production which conform to specifications in accordance with the terms of ams AG standard warranty as given in the General Terms of Trade Discontinued Information in this datasheet is based on products which conform to specifications in accordance with the terms of ams AG standard warranty as given in the General Terms of Trade, but these products have been superseded and should not be used for new designs ams Datasheet [v1-00] 2016-Jul-11 TSL267 - Revision Information Revision Information Changes from 033E (2007-Sep) to current revision 1-00 (2016-Jul-11) Page Content of TAOS datasheet was converted to the latest ams design Added Key Benefits & Features 1 Updated note under Figure 16 11 Updated Figure 18 13 Note(s): 1. Page and figure numbers for the previous version may differ from page and figure numbers in the current revision. 2. Correction of typographical errors is not explicitly mentioned. ams Datasheet [v1-00] 2016-Jul-11 Page 17 Document Feedback TSL267 - Content Guide Content Guide Page 18 Document Feedback 1 1 2 General Description Key Benefits & Features Functional Block Diagram 3 4 5 7 8 Pin Assignments Absolute Maximum Ratings Electrical Characteristics Parameter Measurement Information Typical Characteristics 10 10 Application Information PCB Pad Layout 11 13 14 15 16 17 Mechanical Data Ordering & Contact Information RoHS Compliant & ams Green Statement Copyrights & Disclaimer Document Status Revision Information ams Datasheet [v1-00] 2016-Jul-11