29
1
<________ 66,5 mm /2.61 in ________> <_______________ 87,5 mm /3.45 in _______________>
<___33 mm /
__>
1.29 in
<__33 mm /
__>
1.29 in
<___ 38 mm/1.49 in ___>
< _ _ >
VOLUME 1
➊ can be connected: 0.25 mm2 — 4 mm2 "s+f-st";
can be pushed in directly: 0.75 mm2 — 4 mm2 "s" and
0,75 mm2 – 2,5 mm2 "insulated ferrule,
12 mm/0.472 in"
Accessories Series 2002 Appropriate marker systems: WMB/Marker Strips/WMB Inline (see Full Line Catalog W4, Vol. 1, Sec. 14)
Article-specific accessories
4-conductor fuse terminal blocks
gray 2002-1881
➋ - Individual arrangement: 10 A
- Block arrangement: 5 A
Please note touchproof protection from 42 V
End and intermediate plate, 1 mm/0.039 in thick
orange 2002-1892 100 (4 x 25)
gray 2002-1891 100 (4 x 25)
Protective warning marker, with high voltage symbol, black,
for 5 terminal blocks
yellow 2002-115 100 (4 x 25)
Staggered jumpers, light gray, insulated, IN 25 A
2-way 2002-472 100 (4 x 25)
3-way 2002-473 100 (4 x 25)
4-way 2002-474 100 (4 x 25)
5-way 2002-475 50 (2 x 25)
: :
12-way 2002-482 50 (2 x 25)
Test plug adapter, for test plug Ø 4 mm/0.157 in
2009-174 100 (4 x 25)
Testing tap, for max. 2.5 mm2/AWG 14
2009-182 100 (4 x 25)
Two-way marking adapter,
pivotable
2002-121 50 (2 x 25)
Test plug, with cable 500mm/1’7.7’’, Ø 2 mm/0.079 in
red 210-136 50 (5 x 10)
The rated currents of the fuse cartridges are
defined differently in international standards.
Due to the different current rating definitions,
the recommended current-carrying permanent
capacity of the fuses is max. 80% of their rated
current according to DIN 72581 part 3 (for an
ambient operating temperature of 23°C).
Selecting the correct fuse cartrigde is important
for product safety within applications as well as
the service life/operational reliability of the fuse
cartrigdes. Fuse cartrigdes can operate perfectly
as protection (break-off point) if they are properly
selected and are used in accordance with
the manufacturers specifications.
In general it is necessary to test fuse cartridges
under normal conditions and operational failures
within your application.
With regard to the product safety, it is in
general necessary to test the fuse in the
appliance under normal conditions and
operational failures.
End and intermediate plate, 1 mm/0.039 in thick
orange 2002-1692 100 (4 x 25)
gray 2002-1691 100 (4 x 25)
Insulation stop, 5 pcs/strip 200 strips
light gray 2002-171 0.25-0.5 mm2
dark gray 2002-172 0.75-1 mm2
Push-in type jumper bars, light gray, insulated, IN 25 A
2-way 2002-402 200 (8 x 25)
3-way 2002-403 200 (8 x 25)
4-way 2002-404 200 (8 x 25)
5-way 2002-405 100 (4 x 25)
: :
10-way 2002-410 100 (4 x 25)
Push-in type jumper bars, light gray, insulated, IN 25 A
1 - 3 2002-433 200 (8 x 25)
1 - 4 2002-434 200 (8 x 25)
1 - 5 2002-435 100 (4 x 25)
: :
1 - 10 2002-440 100 (4 x 25)
Modular TOPJOB®S connector,
for jumper contact slot
1 pole 2002-511 100 (4 x 25)
Spacer, modular 2002-549 100 (4 x 25)
2-conductor fuse terminal blocks
gray 2002-1681
➋ - Individual arrangement: 10 A
- Block arrangement: 5 A
Please note touchproof protection from 42 V
Blade-type fuses acc. to DIN 72581-3f /
ISO 8820-3 (not offered by WAGO)
Item no. Pack. unit Item no. Pack. unit
?
Fuse Terminal Blocks for Blade-Type Fuses
acc. to DIN 72581-3f, ISO 8820-3, Series 2002
0.25 — 2.5 (4) mm2
➊ AWG 22 — 12
400 V/6 kV/3
IN 10 A ➋
Terminal block width 5.2 mm / 0.205 in
L 10 — 12 mm / 0.43 in
0.25 — 2.5 (4) mm2
➊ AWG 22 — 12
400 V/6 kV/3
IN 10 A ➋
Terminal block width 5.2 mm / 0.205 in
L 10 — 12 mm / 0.43 in
S
34
1
<_____ 57,2mm /2.26in _____>
<_______ 66,5mm /2.62 in _______>
<______ 57,2mm /2.26in ______>
<_______ 66,5mm /2.62in _______>
VOLUME 1
Article-specific accessories
Description
Fuse disconnect terminal block
with pivotable fuse holder,
for DIN 35 rail,
for miniature metric fuses 5 x 20 mm
5 x 20 mm
5 x 20 mm
2-conductor fuse terminal block with end plate,
without blown fuse indication
gray 2002-1611 50
2-conductor fuse terminal blocks with end plate,
with blown fuse indication by LED
gray 12 — 30 V ≃ ➌ 2002-1611/1000-541
50
gray 30 — 65 V ≃ ➌ 2002-1611/1000-542
50
gray 110 — 250 V ≃ 2002-1611/1000-836
50
?
Fuse Disconnect Terminal Blocks with Pivotable Fuse Holder,
2.5 (4) mm2/AWG 12, for Miniature Metric Fuses 5 x 20 mm, Series 2002
➊
800 V = rated voltage
8 kV = rated surge voltage
3 = pollution degree
(see also Full Line Catalog W4, Volume 1, Section 15)
➋
Nominal voltage and current are given
by the LED or fuse
➌
Leakage current in case of blown fuse:
LED 6 mA
0.25 — 2.5 (4) mm2
AWG 22 — 12
250 V/6 kV/3 ➊
6.3 A ➋
Terminal block width 6.2 mm / 0.244 in
L 10 — 12 mm / 0.43 in
0.25 — 2.5 (4) mm2
AWG 22 — 12
250 V/6 kV/3 ➊
6.3 A ➋
Terminal block width 6.2 mm / 0.244 in
L 10 — 12 mm / 0.43 in
Item no. Pack. unit Item no. Pack. unit
Accessories
Appropriate marker systems: WMB/Marker Strips/WMB Inline (see Full Line Catalog W4, Volume 1, Section 14)
End plate for fuse terminal blocks, 2 mm/0.079 in thick
gray 2002-991 100 (4x25)
orange 2002-992 100 (4x25)
End plate for fuse terminal blocks, 2 mm/0.079 in thick
gray 2002-991 100 (4x25)
orange 2002-992 100 (4x25)
Insulation stop, 5 pcs/strip 200 strips
light gray 2002-171 0.25-0.5 mm2
dark gray 2002-172 0.75-1 mm2
must be singularized
Protective warning marker, with high voltage symbol, black,
for 5 terminal blocks
yellow 2002-115 100 (4 x 25)
must be singularized
Push-in type jumper bars, light gray, insulated, IN 25 A
2-way 2004-402 200 (8 x 25)
3-way 2004-403 200 (8 x 25)
4-way 2004-404 200 (8 x 25)
5-way 2004-405 100 (4 x 25)
: :
10-way 2004-410 100 (4 x 25)
Push-in type jumper bars, light gray, insulated, IN 25 A
1 - 3 2004-433 200 (8 x 25)
1 - 4 2004-434 200 (8 x 25)
1 - 5 2004-435 100 (4 x 25)
: :
1 - 10 2004-440 100 (4 x 25)
Test plug, with cable 500 mm/1’7.7’’, Ø 2 mm/0.079 in Ø
red 210-136 50 (5 x 10)
Insulation stop, 5 pcs/strip 200 strips
light gray 2002-171 0.25-0.5 mm2
dark gray 2002-172 0.75-1 mm2
must be singularized
Protective warning marker, with high voltage symbol, black,
for 5 terminal blocks
yellow 2002-115 100 (4 x 25)
must be singularized
Push-in type jumper bars, light gray, insulated, IN 25 A
2-way 2004-402 200 (8 x 25)
3-way 2004-403 200 (8 x 25)
4-way 2004-404 200 (8 x 25)
5-way 2004-405 100 (4 x 25)
: :
10-way 2004-410 100 (4 x 25)
Push-in type jumper bars, light gray, insulated, IN 25 A
1 - 3 2004-433 200 (8 x 25)
1 - 4 2004-434 200 (8 x 25)
1 - 5 2004-435 100 (4 x 25)
: :
1 - 10 2004-440 100 (4 x 25)
Test plug, with cable 500 mm/1’7.7’’, Ø 2 mm/0.079 in Ø
red 210-136 50 (5 x 10)
35
1
<______ 57,2mm /2.26in ______>
<_____________ 87,5mm /3.45in _____________>
<______ 57,2mm /2.26in ______>
<_____________ 87,5mm /3.45in _____________>
S
VOLUME 1
Fuse terminal blocks with a width of 6.2 mm/0.244 in
can be assembled adjacent to each other.
At the end of an assembly, if there is no adjacent fuse
or disconnect terminal block, an end plate for fuse
terminal blocks must be used.
When selecting miniature metric fuses, the maximum
power loss listed below should not be exceeded. The
power loss is determined according to IEC or EN
60947-7-3/VDE 0611-6 at 23°C. The temperature
rise of the terminal blocks must be checked according
to their application and mounting. Higher ambient tem-
peratures represent an additional impact on miniature
metric fuses. Therefore, in such applications the rated
current must be reduced if necessary.
More details from the manufacturer.
Appropriate marker systems:
WMB/Marker Strips/WMB Inline (see Full Line Catalog W4, Volume 1, Section 14)
0.25 — 2.5 (4) mm2
AWG 22 — 12
250 V/6 kV/3 ➊
6.3 A ➋
Terminal block width 6.2 mm / 0.244 in
L 10 — 12 mm / 0.43 in
0.25 — 2.5 (4) mm2
AWG 22 — 12
250 V/6 kV/3 ➊
6.3 A ➋
Terminal block width 6.2 mm / 0.244 in
L 10 — 12 mm / 0.43 in
4-conductor fuse terminal block with end plate,
without blown fuse indication
gray 2002-1811 50
4-conductor fuse terminal blocks with end plate,
with blown fuse indication by LED
gray 12 — 30 V ≃
➌
2002-1811/1000-541
50
gray 30 — 65 V ≃
➌
2002-1811/1000-542
50
gray 110 — 250 V ≃
2002-1811/1000-836
50
Item no. Pack. unit Item no. Pack. unit
End plate for fuse terminal blocks, 2 mm/0.079 in thick
gray 2002-991 100 (4x25)
orange 2002-992 100 (4x25)
End plate for fuse terminal blocks, 2 mm/0.079 in thick
gray 2002-991 100 (4x25)
orange 2002-992 100 (4x25)
Protective warning marker and insulation stop
must be singularized.
Due to the 6.2 mm/0.244 in width of the
fuse terminal blocks with pivotable fuse holder,
2004 Series jumpers must be used.
Insulation stop, 5 pcs/strip 200 strips
light gray 2002-171 0.25-0.5 mm2
dark gray 2002-172 0.75-1 mm2
must be singularized
Protective warning marker, with high voltage symbol, black,
for 5 terminal blocks
yellow 2002-115 100 (4 x 25)
must be singularized
Push-in type jumper bars, light gray, insulated, IN 25 A
2-way 2004-402 200 (8 x 25)
3-way 2004-403 200 (8 x 25)
4-way 2004-404 200 (8 x 25)
5-way 2004-405 100 (4 x 25)
: :
10-way 2004-410 100 (4 x 25)
Push-in type jumper bars, light gray, insulated, IN 25 A
1 - 3 2004-433 200 (8 x 25)
1 - 4 2004-434 200 (8 x 25)
1 - 5 2004-435 100 (4 x 25)
: :
1 - 10 2004-440 100 (4 x 25)
Test plug, with cable 500 mm/1’7.7’’, Ø 2 mm/0.079 in Ø
red 210-136 50 (5 x 10)
Insulation stop, 5 pcs/strip 200 strips
light gray 2002-171 0.25-0.5 mm2
dark gray 2002-172 0.75-1 mm2
must be singularized
Protective warning marker, with high voltage symbol, black,
for 5 terminal blocks
yellow 2002-115 100 (4 x 25)
must be singularized
Push-in type jumper bars, light gray, insulated, IN 25 A
2-way 2004-402 200 (8 x 25)
3-way 2004-403 200 (8 x 25)
4-way 2004-404 200 (8 x 25)
5-way 2004-405 100 (4 x 25)
: :
10-way 2004-410 100 (4 x 25)
Push-in type jumper bars, light gray, insulated, IN 25 A
1 - 3 2004-433 200 (8 x 25)
1 - 4 2004-434 200 (8 x 25)
1 - 5 2004-435 100 (4 x 25)
: :
1 - 10 2004-440 100 (4 x 25)
Test plug, with cable 500 mm/1’7.7’’, Ø 2 mm/0.079 in Ø
red 210-136 50 (5 x 10)
Miniature metric fuses 5 x 20
Series
Item No.
Overload and
short circuit protection Short circuit
protection only
2002-1611
2002-1811
Individual
arrangement Group
arrangement
Individual
arrangement Group
arrangement
Fuse terminal blocks
1.6 W 1.6 W 2.5 W 2.5 W
2002-1811/....-....
2002-1611/....-.... 1.6 W 1.6 W 2.5 W 2.5 W
Application notes
36
1
<______ 71 mm /2.79 in ➌ ______>
<____________________ ➊ ➋ ____________________>
VOLUME 1
Leakage current in
case of blown fuse
LED 5 — 20 mA,
Neon lamp <0.4 mA
The use of pluggable fuse holders with rail mounted
terminal blocks for protection of control circuits
offers many advantages to the user since
the function and the wiring are accomplished by
two separate parts:
● no additional cost for assembly and wiring
●
no risk of accidental contact with live parts
during disconnection of fuse plug
●
in case of exchanging a defective fuse the fuse
plug is completely separated from the carrier
terminal block
●
therefore safe exchange of the fuse away from
current carrying parts
●
the fuse plug can be taken away by the
serviceman avoiding unintentional reclosing of
the circuit by another person
●
quick exchange of a fuse by using a prepared
“stand-by plug.”
Further advantages:
●
optional LED indicates blown fuse
●
marking facility on the fuse plug for clear coordination
to the correct carrier terminal block
(WSB-Quick Marking System 4 mm/0.157 in)
●
two touchproof test slots
●
high density with only 6,1 mm/0.24 in width of
terminal block/fuse plug
●
instead of a fuse, a shorting link may be used
as a disconnect plug.
When corresponding Neutral-circuit is adjacent to
a fuse plug, a 5.2 mm/0.205 in wide space saving
terminal block may be used, as a 6.1 mm/0.24 in
fuse plug may overlap the terminal block.
See diagram below.
Description
Open side of terminal block
Terminal block width 5.2 mm/0.205 in
gray 2002-1661 50
1 mm/0.039 thick
orange 2002-1692 100 (4 x 25)
gray 2002-1691 100 (4 x 25)
Terminal block width 6 mm/0.236 in
gray 2002-1861 50
1 mm/0.039 thick
orange 2002-1892 100 (4 x 25)
gray 2002-1891 100 (4 x 25)
281-503 250
(10 x 25)
2 mm/0.079 thick
orange 2002-0991 100 (4 x 25)
gray 2002-0992 100 (4 x 25)
2-conductor carrier terminal block ➊,
0.25 — 2.5 (4) mm2/AWG 22 —12
Stripped length 9 —10 mm/0.37 in
End and intermediate plate,
for 2-cond. carrier term. block
Item No. 2002-1661
4-conductor carrier terminal block ➋,
0.25 — 2.5 (4) mm2/AWG 22 —12
Stripped length 10
—12 mm/0.43 in
End and intermediate plate,
for 4-cond. carrier term. block
Item No. 2002-1861
Shorting link, 5 x 20 mm,
6.3 A, if the fuse plug is used as
disconnect plug
End plate for fuse plug
Fuse plug,
for miniature metric fuses
5 x 20 mm
Fuse plug, same as above,
with additional indicator lamp,
LED, AC/DC 12 — 30 V,
LED, AC/DC 30 — 65 V,
can be used in both switching
directions
AC/DC 120 V — 230 V
6.1 mm/0.24 in width with pull-tab
2004-0911 50
6.1 mm/0.24 in width with pull-tab
2004-0911/1000-0541 5 0
2004-0911/1000-0542 5 0
6.1 mm/0.24 in width with pull-tab
2004-0911/1000-0836 5 0
Terminal blocks and accessories Appropriate marker systems: Terminal block WMB/Marker Strips
?
Fuse Plugs, Series 2004
and Carrier Terminal Blocks, Series 2002
250 V max.*
6.3 max. * Electrical ratings are given by the fuse or nomi-
nal voltage of the indicator lamp respectively.
Item no. Pack. unit
Miniature metric fuses 5 x 20
Series
Item No.
Overload and
short circuit protection Short circuit
protection only
2004-0911
2004-0911/....-....
Individual
arrangement Group
arrangement
Individual
arrangement Group
arrangement
Fuse terminal blocks
1.6 W 1.6 W 2.5 W 2.5 W
➊ 66.5 mm/2.62 in (2-conductor)
➋ 87.5 mm/3.45 in (4-conductor)
➌ with inserted fuse plug Open side of terminal block left
