High Speed, Low Noise Video Op Amp AD829 Data Sheet GENERAL DESCRIPTION The"% is a low noise (1.7 nV/Hz), high speed op amp with custom compensation that provides the user with gains of 1 to 20 while maintaining a bandwidth >50 MHz. Its 0.04 differential phase and 0.02% differential gain performance at 3.58 MHz and 4.43 MHz, driving reverse-terminated 50 or 75 cables, makes it ideally suited for professional video applications. The AD829 achieves its 230 V/s uncompensated slew rate and 750 MHz gain bandwidth while requiring only 5 mA of current from power supplies. The external compensation pin of the AD829 gives it exceptional versatility. For example, compensation can be selected to optimize the bandwidth for a given load and power supply voltage. As a gain-of-2 line driver, the -3 dB bandwidth can be increased to 95 MHz at the expense of 1 dB of peaking. Its output can also be clamped at its external compensation pin. The AD829 exhibits excellent dc performance. It offers a minimum open-loop gain of 30 V/mV into loads as low as 500 , a low input voltage noise of 1.7 nV/Hz, and a low input offset voltage of 1 mV maximum. Common-mode rejection and power supply rejection ratios are both 120 dB. This op amp is also useful in multichannel, high speed data conversion where its fast (90 ns to 0.1%) settling time is important. In such applications, the AD829 serves as an input buffer for 8-bit to 10-bit ADCs and as an output I/V converter for high speed DACs. CONNECTION DIAGRAM 8 OFFSET NULL -IN 2 7 +VS +IN 3 6 OUTPUT 5 CCOMP OFFSET NULL 1 AD829 TOP VIEW (Not to Scale) -VS 4 NC OFFSET NULL NC OFFSET NULL NC Figure 1. 8-Lead PDIP (N), CERDIP (Q), and SOIC (R) 3 2 1 20 19 18 NC NC 4 -IN 5 +IN 7 17 +V TOP VIEW (Not to Scale) 16 NC 15 OUTPUT 14 NC NC = NO CONNECT NC NC 10 11 12 13 CCOMP 9 -V NC 8 00880-002 NC 6 AD829 NC High speed 120 MHz bandwidth, gain = -1 230 V/s slew rate 90 ns settling time to 0.1% Ideal for video applications 0.02% differential gain 0.04 differential phase Low noise 1.7 nV/Hz input voltage noise 1.5 pA/Hz input current noise Excellent dc precision 1 mV maximum input offset voltage (over temperature) 0.3 V/C input offset drift Flexible operation Specified for 5 V to 15 V operation 3 V output swing into a 150 load External compensation for gains 1 to 20 5 mA supply current Available in tape and reel in accordance with EIA-481A standard 00880-001 FEATURES Figure 2. 20-Terminal LCC Operating as a traditional voltage feedback amplifier, the AD829 provides many of the advantages that a transimpedance amplifier offer. A bandwidth >50 MHz can be maintained for a range of gains through the replacement of the external compensation capacitor. The AD829 and the transimpedance amplifier are both unity-gain stable and provide similar voltage noise performance (1.7 nV/Hz); however, the current noise of the AD829 (1.5 pA/Hz) is less than 10% of the noise of transimpedance amplifiers. The inputs of the AD829 are symmetrical. PRODUCT HIGHLIGHTS 1. 2. 3. 4. 5. The input voltage noise of 2 nV/Hz, current noise of 1.5 pA/Hz, and 50 MHz bandwidth for gains of 1 to 20 make the AD829 an ideal preamp. A differential phase error of 0.04 and a 0.02% differential gain error, at the 3.58 MHz NTSC, 4.43 MHz PAL, and SECAM color subcarrier frequencies, make the op amp an outstanding video performer for driving reverse-terminated 50 and 75 cables to 1 V (at their terminated end). The AD829 can drive heavy capacitive loads. Performance is fully specified for operation from 5 V to 15 V supplies. The AD829 is available in PDIP, CERDIP, and small outline packages. Chips and MIL-STD-883B parts are also available. The 8-lead SOIC is available for the extended temperature range (-40C to +125C). Rev. I Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 (c)2011 Analog Devices, Inc. All rights reserved. AD829 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 Test Circuits ..................................................................................... 11 General Description ......................................................................... 1 Theory of Operation ...................................................................... 12 Connection Diagram ....................................................................... 1 Externally Compensating the AD829...................................... 12 Product Highlights ........................................................................... 1 Shunt Compensation ................................................................. 12 Revision History ............................................................................... 2 Current Feedback Compensation ............................................ 13 Specifications..................................................................................... 3 Low Error Video Line Driver ................................................... 15 Absolute Maximum Ratings............................................................ 5 Thermal Characteristics .............................................................. 5 High Gain Video Bandwidth, 3-Op-Amp Instrumentation Amplifier ..................................................................................... 16 Metallization Photo ...................................................................... 5 Outline Dimensions ....................................................................... 17 ESD Caution .................................................................................. 5 Ordering Guide .......................................................................... 19 Typical Performance Characteristics ............................................. 6 REVISION HISTORY 10/11--Rev. H to Rev. I Change to Table 2 ............................................................................. 5 4/09--Rev. G to Rev. H Changes to Features.......................................................................... 1 Changes to Quiescent Current Parameter, Table 1 ...................... 4 Changes to Table 2 ............................................................................ 5 Added Thermal Characteristics Section and Table 3 .................. 5 Updated Outline Dimensions ....................................................... 17 Changes to Ordering Guide .......................................................... 19 2/03--Rev. E to Rev. F Renumbered Figures ......................................................... Universal Changes to Product Highlights .......................................................1 Changes to Specifications .................................................................2 Changes to Absolute Maximum Ratings ........................................4 Changes to Ordering Guide .............................................................4 Updated Outline Dimensions ....................................................... 13 4/04--Rev. F to Rev. G Added Figure 1; Renumbered Sequentially .................................. 4 Changes to Ordering Guide ............................................................ 5 Updated Table I ............................................................................... 11 Updated Figure 15 .......................................................................... 12 Updated Figure 16 .......................................................................... 13 Updated Outline Dimensions ....................................................... 14 Rev. I | Page 2 of 20 Data Sheet AD829 SPECIFICATIONS TA = 25C and VS = 15 V dc, unless otherwise noted. Table 1. Parameter INPUT OFFSET VOLTAGE Conditions tMIN to tMAX VS 5 V, 15 V Min AD829JR Typ Max 0.2 1 Min AD829AR Typ Max 0.2 1 1 Offset Voltage Drift INPUT BIAS CURRENT 0.3 3.3 7 3.3 7 5 V, 15 V 50 8.2 500 50 9.5 500 5 V, 15 V 5 V 0.5 30 15 V 20 50 tMIN to tMAX Offset Current Drift OPEN-LOOP GAIN VO = 2.5 V, RL = 500 RL = 150 tMIN to tMAX VO = 10 V, RL = 1 k RL = 500 tMIN to tMAX DYNAMIC PERFORMANCE Gain Bandwidth Product Full Power Bandwidth 1, 2 Slew Rate2 Settling Time to 0.1% Phase Margin2 DIFFERENTIAL GAIN ERROR 3 DIFFERENTIAL PHASE ERROR3 COMMON-MODE REJECTION POWER SUPPLY REJECTION INPUT VOLTAGE NOISE INPUT CURRENT NOISE VO = 2 V p-p, RL = 500 VO = 20 V p-p, RL = 1 k RL = 500 RL = 1 k AV = -19 -2.5 V to +2.5 V 10 V step CL = 10 pF RL = 1 k RL = 100 , CCOMP = 30 pF RL = 100 , CCOMP = 30 pF VCM = 2.5 V VCM = 12 V tMIN to tMAX VS = 4.5 V to 18 V tMIN to tMAX f = 1 kHz f = 1 kHz 1 5 V, 15 V 5 V, 15 V tMIN to tMAX INPUT OFFSET CURRENT AD829AQ/AD829S Min Typ Max 0.1 0.5 0.3 500 65 40 65 30 40 20 50 85 20 50 100 85 20 mV V/C 3.3 7 A 50 9.5 500 A nA 500 0.5 nA nA/C 65 V/mV 40 V/mV V/mV V/mV 500 30 100 0.5 0.3 0.5 20 Unit mV 100 85 V/mV V/mV 20 5 V 15 V 5 V 600 750 25 600 750 25 600 750 25 MHz MHz MHz 15 V 3.6 3.6 3.6 MHz 5 V 15 V 150 230 150 230 150 230 V/s V/s 5 V 65 65 65 ns 15 V 15 V 90 90 90 ns 15 V 60 0.02 60 0.02 60 0.02 Degrees % 15 V 0.04 0.04 0.04 Degrees 120 120 dB dB dB dB 5 V 15 V 100 100 96 98 120 120 100 100 96 98 120 94 15 V 15 V 120 120 100 100 96 98 120 94 1.7 1.5 2 Rev. I | Page 3 of 20 120 94 1.7 1.5 2 1.7 1.5 2 dB nV/Hz pA/Hz AD829 Parameter INPUT COMMON-MODE VOLTAGE RANGE Data Sheet Conditions VS 5 V Min 15 V OUTPUT VOLTAGE SWING RL = 500 RL = 150 RL = 50 RL = 1 k RL = 500 Short-Circuit Current INPUT CHARACTERISTICS Input Resistance (Differential) Input Capacitance (Differential) 4 Input Capacitance (Common Mode) CLOSED-LOOP OUTPUT RESISTANCE POWER SUPPLY Operating Range Quiescent Current 5 V 5 V 5 V 15 V 15 V 5 V, 15 V 3.0 2.5 12 10 AV = +1, f = 1 kHz AD829JR Typ Max +4.3 -3.8 +14.3 -13.8 3.6 3.0 1.4 13.3 12.2 32 12 10 -3.8 +14.3 -13.8 3.6 3.0 1.4 13.3 12.2 32 AD829AQ/AD829S Min Typ Max +4.3 Unit V -3.8 +14.3 -13.8 3.6 3.0 1.4 13.3 12.2 32 V V V V V V V V mA 3.0 2.5 12 10 13 13 k 5 5 5 pF 1.5 1.5 1.5 pF 2 2 2 m 4.5 tMIN to tMAX Number of transistors 3.0 2.5 AD829AR Typ Max +4.3 13 5 V 5 15 V 5.3 tMIN to tMAX TRANSISTOR COUNT Min 18 6.5 8.0 6.8 8.3 46 4.5 5 5.3 46 Full power bandwidth = slew rate/2 VPEAK. Tested at gain = 20, CCOMP = 0 pF. 3 3.58 MHz (NTSC) and 4.43 MHz (PAL and SECAM). 4 Differential input capacitance consists of 1.5 pF package capacitance plus 3.5 pF from the input differential pair. 1 2 Rev. I | Page 4 of 20 18 6.5 8.0 6.8 9.0 4.5 5 5.3 46 18 6.5 8.7 6.8 9.0 V mA mA mA mA Data Sheet AD829 ABSOLUTE MAXIMUM RATINGS METALLIZATION PHOTO Table 2. OFFSET NULL 1 Rating 18 V 1.3 W 0.9 W 1.3 W 0.8 W 6 V Indefinite +VS 7 OUTPUT 6 0.054 (1.37) CCOMP 5 +IN 3 0C to 70C -40C to +125C -55C to +125C 300C Maximum internal power dissipation is specified so that TJ does not exceed 150C at an ambient temperature of 25C. 2 If the differential voltage exceeds 6 V, external series protection resistors should be added to limit the input current. -VS 4 00880-003 0.067 (1.70) SUBSTRATE CONNECTED TO +VS Figure 3. Metallization Photo; Contact Factory for Latest Dimensions, Dimensions Shown in Inches and (Millimeters) 2.5 Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. THERMAL CHARACTERISTICS 2.0 PDIP LCC 1.5 1.0 CERDIP SOIC 0.5 00880-004 -65C to +150C -65C to +125C 1 0 -55 -45 -35 -25 -15 -5 Table 3. Package Type 8-Lead PDIP (N) 8-Lead CERDIP (Q) 20-Lead LCC (E) 8-Lead SOIC (R) OFFSET NULL 8 -IN 2 MAXIMUM POWER DISSIPATION (W) Parameter Supply Voltage Internal Power Dissipation1 8-Lead PDIP (N) 8-Lead SOIC (R) 8-Lead CERDIP (Q) 20-Terminal LCC (E) Differential Input Voltage2 Output Short-Circuit Duration Storage Temperature Range 8-Lead CERDIP (Q) and 20-Terminal LCC (E) 8-Lead PDIP (N) and 8-Lead SOIC (R) Operating Temperature Range AD829J AD829A AD829S Lead Temperature (Soldering, 60 sec) 5 15 25 35 45 55 65 75 85 95 105 115 125 AMBIENT TEMPERATURE (C) JA 100 (derates at 8.7 mW/C) 110 (derates at 8.7 mW/C) 77 125 (derates at 6 mW/C) Unit C/W C/W C/W C/W Figure 4. Maximum Power Dissipation vs. Temperature ESD CAUTION Rev. I | Page 5 of 20 AD829 Data Sheet TYPICAL PERFORMANCE CHARACTERISTICS 15 +VOUT 10 -VOUT 5 0 0 5 10 SUPPLY VOLTAGE (V) 5.5 5.0 4.5 4.0 20 15 00880-008 QUIESCENT CURRENT (mA) 6.0 00880-005 0 Figure 5. Input Common-Mode Range vs. Supply Voltage 20 15 INPUT BIAS CURRENT (A) -5 15 +VOUT 10 -VOUT 5 00880-006 RL = 1k 0 0 5 10 15 -4 VS = 5V, 15V -3 -2 -60 20 -40 -20 SUPPLY VOLTAGE (V) Figure 6. Output Voltage Swing vs. Supply Voltage 20 40 60 80 TEMPERATURE (C) 100 120 140 15V SUPPLIES 20 15 10 100 1k LOAD RESISTANCE () 00880-007 5V SUPPLIES 5 10 AV = 20 CCOMP = 0pF 1 0.1 AV = 1 CCOMP = 68pF 0.01 0.001 1k 10k Figure 7. Output Voltage Swing vs. Resistive Load 00880-010 CLOSED-LOOP OUTPUT IMPEDANCE () 100 25 0 10 0 Figure 9. Input Bias Current vs. Temperature 30 OUTPUT VOLTAGE SWING (V p-p) 10 SUPPLY VOLTAGE (V) Figure 8. Quiescent Current vs. Supply Voltage 20 MAGNITUDE OF THE OUTPUT VOLTAGE (V) 5 00880-009 INPUT COMMON-MODE RANGE (V) 20 10k 100k 1M FREQUENCY (Hz) 10M Figure 10. Closed-Loop Output Impedance vs. Frequency Rev. I | Page 6 of 20 100M Data Sheet AD829 7 120 100 PHASE VS = 15V 5 VS = 5V 80 GAIN 15V SUPPLIES 1k LOAD 80 60 GAIN 5V SUPPLIES 500 LOAD 60 40 40 20 4 -40 -20 0 20 40 60 80 TEMPERATURE (C) 100 120 0 100 140 1k 10k 100k 1M FREQUENCY (Hz) 10M -20 100M Figure 14. Open-Loop Gain and Phase vs. Frequency Figure 11. Quiescent Current vs. Temperature 105 40 NEGATIVE CURRENT LIMIT 100 35 OPEN-LOOP GAIN (dB) POSITIVE CURRENT LIMIT 30 25 20 VS = 15V 95 VS = 5V 90 85 15 -60 -40 -20 0 20 40 60 80 100 120 00880-015 80 VS = 5V 00880-012 75 10 140 100 1k LOAD RESISTANCE () AMBIENT TEMPERATURE (C) 10k Figure 15. Open-Loop Gain vs. Resistive Load Figure 12. Short-Circuit Current Limit vs. Ambient Temperature 120 65 VS = 15V AV = +20 CCOMP = 0pF +SUPPLY 100 60 PSRR (dB) -SUPPLY 55 80 60 50 45 -60 00880-013 40 -40 -20 0 20 40 60 80 100 120 00880-016 SHORT-CIRCUIT CURRENT LIMIT (mA) 0 CCOMP = 0pF CCOMP = 0pF 20 1k 140 TEMPERATURE (C) 10k 100k 1M FREQUENCY (Hz) 10M 100M Figure 16. Power Supply Rejection Ratio (PSRR) vs. Frequency Figure 13. -3 dB Bandwidth vs. Temperature Rev. I | Page 7 of 20 00880-014 3 -60 00880-011 20 -3dB BANDWIDTH (MHz) PHASE (Degrees) OPEN-LOOP GAIN (dB) QUIESCENT CURRENT (mA) 100 6 AD829 Data Sheet -70 120 VIN = 3V RMS AV = -1 CCOMP = 30pF CL = 100pF -75 100 -80 -85 THD (dB) CMRR (dB) 80 60 RL = 500 -90 -95 -100 RL = 2k 40 10k 100k 1M FREQUENCY (Hz) -110 100 100M 10M 300 1k 3k 10k 30k 100k FREQUENCY (Hz) Figure 17. Common-Mode Rejection Ratio (CMRR) vs. Frequency Figure 20. Total Harmonic Distortion (THD) vs. Frequency 30 -20 VS = 15V RL = 1k AV = +20 CCOMP = 0pF 25 VIN = 2.25V RMS AV = -1 RL = 250 CL = 0pF CCOMP = 30pF -30 THIRD HARMONIC 20 THD (dB) 15 VS = 5V RL = 500 AV = +20 CCOMP = 0pF 10 -40 -50 SECOND HARMONIC -60 00880-018 5 0 1 10 00880-021 OUTPUT VOLTAGE (V p-p) 00880-020 20 1k -105 00880-017 CCOMP = 0pF -70 100 0 500k 1.0M INPUT FREQUENCY (MHz) 2.0M 1.5M FREQUENCY (Hz) Figure 21. Second and Third THD vs. Frequency Figure 18. Large Signal Frequency Response 5 10 4 2 1% 0.1% 1% 0.1% 0 ERROR AV = -19 CCOMP = 0pF -2 -4 -6 -8 -10 0 20 40 60 80 100 SETTLING TIME (ns) 120 140 4 3 2 1 0 10 160 00880-022 INPUT VOLTAGE NOISE (nV/ Hz) 6 00880-019 OUTPUT SWING FROM 0 TO V 8 100 1k 10k 100k 1M FREQUENCY (Hz) Figure 22. Input Voltage Noise Spectral Density Figure 19. Output Swing and Error vs. Settling Time Rev. I | Page 8 of 20 10M Data Sheet AD829 400 AV = +20 SLEW RATE 10% TO 90% 20mV 350 20ns 100% SLEW RATE (V/s) 90 RISE 300 VS = 15V FALL 250 RISE 200 10 FALL 0% VS = 5V 100 -60 -40 -20 0 20 40 60 80 TEMPERATURE (C) 100 120 00880-028 00880-023 150 140 Figure 23. Slew Rate vs. Temperature Figure 26. Gain-of-2 Follower Small Signal Pulse Response (See Figure 32) 0.03 0.043 0.05 DIFFERENTIAL PHASE 100% 90 DIFFERENTIAL GAIN (%) DIFFERENTIAL GAIN 0.01 50ns 10 0% 0.04 0.03 5 00880-030 00880-024 DIFFERENTIAL PHASE (Degrees) 2V 0.02 15 10 SUPPLY VOLTAGE (V) Figure 24. Differential Phase and Gain vs. Supply Voltage 200mV Figure 27. Gain-of-20 Follower Large Signal Pulse Response (See Figure 33) 50ns 50mV 20ns 100% 90 10 10 0% 0% 00880-031 00880-027 90 Figure 25. Gain-to-2 Follower Large Signal Pulse Response (See Figure 32) Figure 28. Gain-of-20 Follower Small Signal Pulse Response (See Figure 33) Rev. I | Page 9 of 20 AD829 Data Sheet 200mV 50ns 20mV 90 10 10 0% 0% 00880-034 100% 90 00880-033 100% 20ns Figure 29. Unity-Gain Inverter Large Signal Pulse Response (See Figure 34) Figure 30. Unity-Gain Inverter Small Signal Pulse Response (See Figure 34) Rev. I | Page 10 of 20 Data Sheet AD829 TEST CIRCUITS CCOMP (EXTERNAL) +VS 0.1F 5 - 7 AD829 6 4 + 3 8 0.1F 20k 1 OFFSET NULL ADJUST 00880-025 2 -VS Figure 31. Offset Null and External Shunt Compensation Connections +15V CCOMP 15pF 0.1F 50 CABLE 7 HP8130A 5ns RISE TIME + 3 5 AD829 50 50 CABLE 50 6 - 2 4 300k 5pF 0.1F -15V TEKTRONIX TYPE 7A24 PREAMP 50 00880-026 300k Figure 32. Follower Connection, Gain = 2 +15V 0.1F 100 2 FET PROBE 7 - AD829 5 3 6 TEKTRONIX TYPE 7A24 PREAMP + 4 2k 1pF 0.1F -15V 105k CCOMP = 0pF 00880-029 HP8130A 5ns RISE TIME 50 CABLE 45 Figure 33. Follower Connection, Gain = 20 5pF 300 +15V 0.1F 300 2 7 - 50 AD829 50 3 6 5 + 4 50 CABLE CCOMP 15pF 0.1F -15V Figure 34. Unity-Gain Inverter Connection Rev. I | Page 11 of 20 TEKTRONIX TYPE 7A24 PREAMP 50 00880-032 50 CABLE HP8130A 5ns RISE TIME AD829 Data Sheet THEORY OF OPERATION The AD829 is fabricated on the Analog Devices, Inc., proprietary complementary bipolar (CB) process, which provides PNP and NPN transistors with similar fTs of 600 MHz. As shown in Figure 35, the AD829 input stage consists of an NPN differential pair in which each transistor operates at a 600 A collector current. This gives the input devices a high transconductance, which in turn gives the AD829 a low noise figure of 2 nV/Hz at 1 kHz. +VS 15 OUTPUT R 500 EXTERNALLY COMPENSATING THE AD829 15 -IN The AD829 is stable with no external compensation for noise gains greater than 20. For lower gains, two different methods of frequency compensating the amplifier can be used to achieve closed-loop stability: shunt and current feedback compensation. 1.2mA OFFSET NULL CCOMP 00880-035 -VS SHUNT COMPENSATION Figure 35. Simplified Schematic The input stage drives a folded cascode that consists of a fast pair of PNP transistors. These PNPs drive a current mirror that provides a differential-input-to-single-ended-output conversion. The high speed PNPs are also used in the current-amplifying output stage, which provides a high current gain of 40,000. Even under heavy loading conditions, the high fTs of the NPN and PNPs, produced using the CB process, permit cascading two stages of emitter followers while maintaining 60 phase margin at closed-loop bandwidths greater than 50 MHz. Figure 36 and Figure 37 show that shunt compensation has an external compensation capacitor, CCOMP, connected between the compensation pin and ground. This external capacitor is tied in parallel with approximately 3 pF of internal capacitance at the compensation node. In addition, a small capacitance, CLEAD, in parallel with resistor R2, compensates for the capacitance at the inverting input of the amplifier. CLEAD 50 COAX CABLE Two stages of complementary emitter followers also effectively buffer the high impedance compensation node (at the CCOMP pin) from the output so that the AD829 can maintain a high dc openloop gain, even into low load impedances (92 dB into a 150 load and 100 dB into a 1 k load). Laser trimming and PTAT biasing ensure low offset voltage and low offset voltage drift, enabling the user to eliminate ac coupling in many applications. 0.1F R1 VIN 2 7 - AD829 50 3 VOUT 6 5 + CCOMP 4 1k 0.1F -VS Figure 36. Inverting Amplifier Connection Using External Shunt Compensation For added flexibility, the AD829 provides access to the internal frequency compensation node. This allows users to customize the frequency response characteristics for a particular application. +VS 50 CABLE 0.1F VIN 3 7 + AD829 50 Unity-gain stability requires a compensation capacitance of 68 pF (Pin 5 to ground), which yields a small signal bandwidth of 66 MHz and slew rate of 16 V/s. The slew rate and gain bandwidth product varies inversely with compensation capacitance. Table 4 and Figure 37 show the optimum compensation capacitance and the resulting slew rate for a desired noise gain. For gains between 1 and 20, choose CCOMP to keep the small signal bandwidth relatively constant. The minimum gain that will still provide stability depends on the value of the external compensation capacitance. R2 +VS 00880-036 +IN 2 4 VOUT 6 5 - R2 1k CCOMP CLEAD 0.1F -VS R1 00880-037 C 12.5pF An RC network in the output stage (see Figure 35) completely removes the effect of capacitive loading when the amplifier compensates for closed-loop gains of 10 or higher. At low frequencies, and with low capacitive loads, the gain from the compensation node to the output is very close to unity. In this case, C is bootstrapped and does not contribute to the compensation capacitance of the device. As the capacitive load increases, a pole forms with the output impedance of the output stage, which reduces the gain, and subsequently, C is incompletely bootstrapped. Therefore, some fraction of C contributes to the compensation capacitance, and the unity-gain bandwidth falls. As the load capacitance is further increased, the bandwidth continues to fall, and the amplifier remains stable. Figure 37. Noninverting Amplifier Connection Using External Shunt Compensation Table 4 gives the recommended CCOMP and CLEAD values, as well as the corresponding slew rates and bandwidth. The capacitor values were selected to provide a small signal frequency response with <1 dB of peaking and <10% overshoot. For Table 4, 15 V Rev. I | Page 12 of 20 Data Sheet AD829 supply voltages should be used. Figure 38 is a graphical extension of Table 4, which shows the slew rate/gain trade-off for lower closed-loop gains, when using the shunt compensation scheme. 100 Slew Rate = 10 100 VS = 15V 1 1 10 100 10 NOISE GAIN SLEW RATE (V/s) SLEW RATE 00880-038 CCOMP (pF) Because both fT and slew rate are functions of the same variables, the dynamic behavior of an amplifier is limited. Because 1k CCOMP Figure 38. Value of CCOMP and Slew Rate vs. Noise Gain CURRENT FEEDBACK COMPENSATION 2I CCOMP then Slew Rate fT =4 kT q This shows that the slew rate is only 0.314 V/s for every megahertz of bandwidth. The only way to increase the slew rate is to increase the fT, and that is difficult because of process limitations. Unfortunately, an amplifier with a bandwidth of 10 MHz can only slew at 3.1 V/s, which is barely enough to provide a full power bandwidth of 50 kHz. The AD829 is especially suited to a form of current feedback compensation that allows for the enhancement of both the full power bandwidth and the slew rate of the amplifier. The voltage gain from the inverting input pin to the compensation pin is large; therefore, if a capacitance is inserted between these pins, the bandwidth of the amplifier becomes a function of its feedback resistor and the capacitance. The slew rate of the amplifier is now a function of its internal bias (2I) and the compensation capacitance. Bipolar, nondegenerated, single-pole, and internally compensated amplifiers have their bandwidths defined as fT = CCOMP is the compensation capacitance. re is the inverse of the transconductance of the input transistors. kT/q approximately equals 26 mV at 27C. 1 I = 2 re C COMP 2 kT C COMP q where: fT is the unity-gain bandwidth of the amplifier. I is the collector current of the input transistor. Table 4. Component Selection for Shunt Compensation Follower Gain 1 2 5 10 20 25 100 Inverter Gain -1 -4 -9 -19 -24 -99 R1 () Open 1k 511 226 105 105 20 R2 () 100 1k 2.0 k 2.05 k 2k 2.49 2k CLEAD (pF) 0 5 1 0 0 0 0 CCOMP (pF) 68 25 7 3 0 0 0 Rev. I | Page 13 of 20 Slew Rate (V/s) 16 38 90 130 230 230 230 -3 dB Small Signal Bandwidth (MHz) 66 71 76 65 55 39 7.5 AD829 Data Sheet Because the closed-loop bandwidth is a function of RF and CCOMP (see Figure 39), it is independent of the amplifier closedloop gain, as shown in Figure 41. To preserve stability, the time constant of RF and CCOMP needs to provide a bandwidth of <65 MHz. For example, with CCOMP = 15 pF and RF = 1 k, the small signal bandwidth of the AD829 is 10 MHz. Figure 40 shows that the slew rate is in excess of 60 V/s. As shown in Figure 41, the closed-loop bandwidth is constant for gains of -1 to -4; this is a property of the current feedback amplifiers. Figure 42 is an oscilloscope photo of the pulse response of a unitygain inverter that has been configured to provide a small signal bandwidth of 53 MHz and a subsequent slew rate of 180 V/s; RF = 3 k and CCOMP = 1 pF. Figure 43 shows the excellent pulse response as a unity-gain inverter, this using component values of RF = 1 k and CCOMP = 4 pF. 5V 200ns 100% 90 RF CCOMP 0.1F R1 7 VIN 2 - 5 AD829 C1* 50 +VS IN4148 3 + -VS <7pF 7pF VOUT RL 1k 10 0% 0.1F CCOMP SHOULD NEVER EXCEED 15pF FOR THIS CONNECTION 00880-039 *RECOMMENDED VALUE OF CCOMP FOR C1 6 4 00880-042 50 COAX CABLE 0pF 15pF Figure 42. Large Signal Pulse Response of the Inverting Amplifier Using Current Feedback Compensation, CCOMP = 1 pF, RF = 3 k, R1 = 3 k Figure 39. Inverting Amplifier Connection Using Current Feedback Compensation 10ns 100% 5V 200ns 90 100% 90 10 20mV 10 0% 00880-040 Figure 43. Small Signal Pulse Response of Inverting Amplified Using Current Feedback Compensation, CCOMP = 4 pF, RF = 1 k, R1 = 1 k Figure 40. Large Signal Pulse Response of Inverting Amplifier Using Current Feedback Compensation, CCOMP = 15 pF, C1 = 15 pF RF = 1 k, R1 = 1 k 15 12 GAIN = -4 -3dB @ 8.2MHz GAIN = -2 -3dB @ 9.6MHz 3 0 GAIN = -1 -3dB @ 10.2MHz -3 -6 -9 -12 VIN = -30dBm VS = 15V RL = 1k RF = 1k CCOMP = 15pF C1 = 15pF -15 100k 00880-041 CLOSED-LOOP GAIN (dB) 9 6 1M 10M FREQUENCY (Hz) 00880-043 0% 100M Figure 41. Closed-Loop Gain vs. Frequency for the Circuit of Figure 38 Rev. I | Page 14 of 20 Data Sheet AD829 Figure 44 and Figure 45 show the closed-loop frequency response of the AD829 for different closed-loop gains and different supply voltages. +15V 50 COAX CABLE 0.1F 15 3 GAIN = -4 CCOMP = 2pF 12 + AD829 50 2 - VOUT 6 5 4 GAIN = -2 CCOMP = 3pF 50k 3pF CCOMP -15V 0.1F 2k GAIN = -1 CCOMP = 4pF 0 00880-046 3 2k -3 Figure 46. Noninverting Amplifier Connection Using Current Feedback Compensation -6 VS = 15V RL = 1k RF = 1k VIN = -30dBm -9 -12 00880-044 CLOSED-LOOP GAIN (dB) 9 6 50 COAX CABLE 50 7 VIN -15 1 10 FREQUENCY (MHz) +15V 0.1F 100 50 COAX 75 CABLE 7 VIN Figure 44. Closed-Loop Frequency Response for the Inverting Amplifier Using Current Feedback Compensation 3 + AD829 75 2 - VOUT 6 75 4 5 30pF CCOMP -20 0.1F 300 -15V 300 5V -26 15V Figure 47. Video Line Driver with a Flatness over Frequency Adjustment -29 -32 LOW ERROR VIDEO LINE DRIVER -35 -38 VIN = -20dBm RL = 1k RF = 1k GAIN = -1 CCOMP = 4pF -41 -44 00880-045 OUTPUT LEVEL (dB) -23 OPTIONAL 2pF TO 7pF FLATNESS TRIM 00880-047 -17 -47 1 10 FREQUENCY (MHz) 100 Figure 45. Closed-Loop Frequency Response vs. Supply for the Inverting Amplifier Using Current Feedback Compensation The buffer circuit shown in Figure 47 drives a back-terminated 75 video line to standard video levels (1 V p-p), with 0.1 dB gain flatness to 30 MHz and with only 0.04 and 0.02% differential phase and gain at the 4.43 MHz PAL color subcarrier frequency. This level of performance, which meets the requirements for high definition video displays and test equipment, is achieved using only 5 mA quiescent current. When a noninverting amplifier configuration using a current feedback compensation is needed, the circuit shown in Figure 46 is recommended. This circuit provides a slew rate twice that of the shunt compensated noninverting amplifier of Figure 47 at the expense of gain flatness. Nonetheless, this circuit delivers 95 MHz bandwidth with 1 dB flatness into a back-terminated cable, with a differential gain error of only 0.01% and a differential phase error of only 0.015 at 4.43 MHz. Rev. I | Page 15 of 20 AD829 Data Sheet HIGH GAIN VIDEO BANDWIDTH, 3-OP-AMP INSTRUMENTATION AMPLIFIER The input amplifiers operate at a gain of 20, while the output op amp runs at a gain of 5. In this circuit, the main bandwidth limitation is the gain/bandwidth product of the output amplifier. Extra care should be taken while breadboarding this circuit because even a couple of extra picofarads of stray capacitance at the compensation pins of A1 and A2 will degrade circuit bandwidth. Figure 48 shows a 3-op-amp instrumentation amplifier circuit that provides a gain of 100 at video bandwidths. At a circuit gain of 100, the small signal bandwidth equals 18 MHz into a FET probe. Small signal bandwidth equals 6.6 MHz with a 50 load. The 0.1% settling time is 300 ns. 3pF +VIN (G = 20) 5 2pF TO 8pF SETTLING TIME AC CMR ADJUST 3 A1 6 AD829 2 1k 2k RG 210 200 1pF 2 A3 AD848 200 3 5 2k 6 2k (G = 5) 3pF 100Hz 1MHz 10MHz 970 2 A2 AD829 +VIN 3 5 6 DC CMR ADJUST 50 INPUT FREQUENCY CMRR +VS +15V (G = 20) 64.6dB 44.7dB 23.9dB PIN 7 10F 0.1F 1F 0.1F 10F 0.1F 1F 0.1F COMM 3pF CIRCUIT GAIN = 4000 +1 5 RG -15V -VS Figure 48. High Gain Video Bandwidth, 3-Op-Amp In-Amp Circuit Rev. I | Page 16 of 20 EACH AMPLIFIER PIN 4 00880-048 1pF Data Sheet AD829 OUTLINE DIMENSIONS 5.00 (0.1968) 4.80 (0.1890) 1 5 6.20 (0.2441) 5.80 (0.2284) 4 1.27 (0.0500) BSC 0.25 (0.0098) 0.10 (0.0040) 0.51 (0.0201) 0.31 (0.0122) COPLANARITY 0.10 SEATING PLANE 0.50 (0.0196) 0.25 (0.0099) 1.75 (0.0688) 1.35 (0.0532) 45 8 0 0.25 (0.0098) 0.17 (0.0067) 1.27 (0.0500) 0.40 (0.0157) COMPLIANT TO JEDEC STANDARDS MS-012-AA CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN. 012407-A 8 4.00 (0.1574) 3.80 (0.1497) Figure 49. 8-Lead Standard Small Outline Package [SOIC_N] Narrow Body (R-8) Dimensions shown in millimeters and (inches) 0.400 (10.16) 0.365 (9.27) 0.355 (9.02) 8 5 1 4 0.280 (7.11) 0.250 (6.35) 0.240 (6.10) 0.100 (2.54) BSC 0.060 (1.52) MAX 0.210 (5.33) MAX 0.015 (0.38) MIN 0.150 (3.81) 0.130 (3.30) 0.115 (2.92) SEATING PLANE 0.022 (0.56) 0.018 (0.46) 0.014 (0.36) 0.325 (8.26) 0.310 (7.87) 0.300 (7.62) 0.195 (4.95) 0.130 (3.30) 0.115 (2.92) 0.015 (0.38) GAUGE PLANE 0.005 (0.13) MIN 0.014 (0.36) 0.010 (0.25) 0.008 (0.20) 0.430 (10.92) MAX COMPLIANT TO JEDEC STANDARDS MS-001 CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN. CORNER LEADS MAY BE CONFIGURED AS WHOLE OR HALF LEADS. Figure 50. 8-Lead Plastic Dual In-Line Package [PDIP] Narrow Body (N-8) Dimensions shown in inches and (millimeters) Rev. I | Page 17 of 20 070606-A 0.070 (1.78) 0.060 (1.52) 0.045 (1.14) AD829 Data Sheet 0.005 (0.13) MIN 8 0.055 (1.40) MAX 5 0.310 (7.87) 0.220 (5.59) 1 4 0.100 (2.54) BSC 0.320 (8.13) 0.290 (7.37) 0.405 (10.29) MAX 0.060 (1.52) 0.015 (0.38) 0.200 (5.08) MAX 0.150 (3.81) MIN 0.200 (5.08) 0.125 (3.18) 0.023 (0.58) 0.014 (0.36) 0.070 (1.78) 0.030 (0.76) SEATING PLANE 0.015 (0.38) 0.008 (0.20) 15 0 CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN. Figure 51. 8-Lead Ceramic Dual In-Line [CERDIP] (Q-8) Dimensions shown in inches and (millimeters) 0.200 (5.08) REF 0.100 (2.54) REF 0.015 (0.38) MIN 0.075 (1.91) REF 0.095 (2.41) 0.075 (1.90) 19 18 0.358 (9.09) 0.342 (8.69) SQ 0.358 (9.09) MAX SQ 0.088 (2.24) 0.054 (1.37) 0.011 (0.28) 0.007 (0.18) R TYP 0.075 (1.91) REF 0.055 (1.40) 0.045 (1.14) 3 20 4 0.028 (0.71) 0.022 (0.56) 1 BOTTOM VIEW 0.050 (1.27) BSC 8 14 13 9 45 TYP 0.150 (3.81) BSC CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN. Figure 52. 20-Terminal Ceramic Leadless Chip Carrier [LCC] (E-20-1) Dimensions shown in inches and (millimeters) Rev. I | Page 18 of 20 022106-A 0.100 (2.54) 0.064 (1.63) Data Sheet AD829 ORDERING GUIDE Model 1 AD829AR AD829AR-REEL AD829AR-REEL7 AD829ARZ AD829ARZ-REEL AD829ARZ-REEL7 AD829JN AD829JNZ AD829JR AD829JR-REEL AD829JR-REEL7 AD829JRZ AD829JRZ-REEL AD829JRZ-REEL7 AD829AQ AD829SQ AD829SQ/883B 5962-9312901MPA AD829SE/883B 5962-9312901M2A AD829JCHIPS AD829SCHIPS AD829AR-EBZ 1 Temperature Range -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C 0C to 70C 0C to 70C 0C to 70C 0C to 70C 0C to 70C 0C to 70C 0C to 70C 0C to 70C -40C to +125C -55C to +125C -55C to +125C -55C to +125C -55C to +125C -55C to +125C Package Description 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead PDIP 8-Lead PDIP 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead SOIC_N 8-Lead CERDIP 8-Lead CERDIP 8-Lead CERDIP 8-Lead CERDIP 20-Lead LCC 20-Lead LCC Die Die Evaluation Board Z = RoHS Compliant Part. Rev. I | Page 19 of 20 Package Option R-8 R-8 R-8 R-8 R-8 R-8 N-8 N-8 R-8 R-8 R-8 R-8 R-8 R-8 Q-8 Q-8 Q-8 Q-8 E-20-1 E-20-1 AD829 Data Sheet NOTES (c)2011 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D00880-0-10/11(I) Rev. I | Page 20 of 20