NUMBER GS-12-149
TYPE PRODUCT SPECIFICATION
TITLE PAGE REVISION
PwrBlade ® Product Specification 1 of 13 AA
AUTHORIZED BY DATE
MT Ruan 29 Jul 16
CLASSIFICATION
UNRESTRICTED
Copyright FCI
Form E-3334
Rev F
GS-01-001
1.0 OBJECTIVE
This specification defines the performance, test, quality and reliability requirements of the PwrBlade
Connector System.
2.0 SCOPE
This specification is applicable to the termination characteristics of separable right angle and vertical headers
when mated to the right angle and vertical receptacles.
3.0 GENERAL
If there is conflict between the product drawings and specifications, the drawing takes precedence.
This document is composed of the following sections:
Paragraph Title
1.0 OBJECTIVE
2.0 SCOPE
3.0 GENERAL
4.0 APPLICABLE DOCUMENTS
5.0 REQUIREMENTS
5.1 Qualification
5.2 Material
5.3 Finish
5.4 Design and construction
5.5 Workmanship
6.0 ELECTRICAL CHARACTERISTICS
7.0 MECHANICAL CHARACTERISTICS
8.0 ENVIRONMENTAL CONDITIONS
9.0 QUALITY ASSURANCE PROVISIONS
9.1 Equipment Calibration
9.2 Inspection Conditions
9.3 Sample Quality and Description
9.4 Acceptance
9.5 Qualification Testing
9.6 Re-qualification Testing
10.0 Reference Documents
Table 2 Qualification Testing Matrix
PDS: Rev :AA STATUS:Released Printed: Jul 29, 2016
NUMBER GS-12-149
TYPE PRODUCT SPECIFICATION
TITLE PAGE REVISION
PwrBlade ® Product Specification 2 of 13 AA
AUTHORIZED BY DATE
MT Ruan 29 Jul 16
CLASSIFICATION
UNRESTRICTED
Copyright FCI
Form E-3334
Rev F
GS-01-001
4.0 APPLICABLE DOCUMENTS
4.1 Specifications
4.1.1 Applicable FCI power blade product drawings
4.2 Federal Specifications
4.2.1 MIL-STD-1344A: Test Methods for Electrical Connectors
4.3 Other Standards and Specifications
4.3.1 UL 94 V-0: Flammability
4.3.2 EIA 364: Test Procedures for Electrical Connectors, Sockets and Coaxial Contacts
4.4 FCI Specifications:
4.4.1 BUS-03-601:Current Rating/30BUS-03-601: Current Rating/30oC Temperature Rise
4.4.2 BUS-03-404: Normal Force Measurement
4.4.3 BUS-12-090: HPC Product Specification
4.4.4 BUS-12-111: HPC Solderless (Press fit) Right Angle Receptacle
5.0 REQUIREMENTS
5.1 Qualification
Connectors furnished under this specification shall be capable of meeting the qualification test
requirements specified herein.
5.2 Material
The material for each component shall be as specified herein or equivalent.
Power Contacts – High Performance Copper Alloy
Signal Header Contacts – Copper Alloy
Signal Receptacle Contacts – Copper Alloy
Receptacle and Plug Housings - Glass Filled HTN (High Temperature Nylon)
PDS: Rev :AA STATUS:Released Printed: Jul 29, 2016
NUMBER GS-12-149
TYPE PRODUCT SPECIFICATION
TITLE PAGE REVISION
PwrBlade ® Product Specification 3 of 13 AA
AUTHORIZED BY DATE
MT Ruan 29 Jul 16
CLASSIFICATION
UNRESTRICTED
Copyright FCI
Form E-3334
Rev F
GS-01-001
5.3 Finish
Refer to plating specification 10064183.
5.4 Design and Construction
Connectors shall be of the design, construction and physical dimensions specified on the applicable
product drawings.
5.4.1 See drawing numbers 51700, 51720, 51740, 51760 and 51866 for test connector
configurations.
5.5 Workmanship includes freedom from blistering, cracks, discoloration, etc.
ELECTRICAL CHARACTERISTICS
6.1 Signal tested at Low Level (LLCR) – The low level contact resistance shall not exceed 20 milliohm
after environmental exposure when measured in accordance with EIA 364 TP 06. The following
details shall apply:
a. Test Voltage – 20 millivolts DC max open circuit.
b. Test Current – Not to exceed 100 milliamps.
6.2 Power tested at Specified Current – The contact resistance at a specified current shall not exceed 0.7
milliohm end of life when measured in accordance with EIA 364 TP32. Test Current 30 amperes DC
6.3 Insulation Resistance – the insulation resistance of mated connectors shall not be less than 10,000
megohms for power contacts, and 500 megohms for signal initially and after environmental exposure
when measured in accordance with EIA 364 TP21
a. Test Voltage 500 volts DC
b. Electrification time – 2 minutes
c. Points of Measurement – Between adjacent Contacts
6.4 Dielectric Withstanding Voltage – There shall be no evidence of arc-over, insulation breakdown, or
excessive leakage current (>1 Milliampere ) when mated connectors are tested in accordance with
EIA 364 TP 20. The following details apply:
a. Test Voltage – 2500 volts DC (power), 1000 volts DC (signal)
b. Test Duration – 60 seconds.
c. Test Condition – (760 Torr – sea level).
PDS: Rev :AA STATUS:Released Printed: Jul 29, 2016
NUMBER GS-12-149
TYPE PRODUCT SPECIFICATION
TITLE PAGE REVISION
PwrBlade ® Product Specification 4 of 13 AA
AUTHORIZED BY DATE
MT Ruan 29 Jul 16
CLASSIFICATION
UNRESTRICTED
Copyright FCI
Form E-3334
Rev F
GS-01-001
6.5 Current Rating – Refer to table 1, the temperature rise above ambient shall not exceed 30 at any
point in the system at specified amperes (Table 1) when mated connectors are tested in accordance
with EIA-364-70, method 1. The following detail shall apply:
a) Ambient Conditions – Still air at 25
b) Stabilize at a single current level until 3 readings at 5 minutes intervals are within 1.
c) Test with single energized contact and with all adjacent power contacts energized.
Table 1: Rated current table (amperes)
Types Pitch
(mm)
Single
Contact
2 adjacent
Contacts*
4 adjacent
Contacts
8 adjacent
Contacts
12 adjacent
Contacts
Power Contact 6.35 48 50* 36 31 30
* 2 adjacent contacts test by wire, the wire size is 6AWG.
Types Pitch
(mm)
Single
Contact
Multiple
contact
Signal Contact 2.54 3 1
7.0 MECHANICAL CHARACTERISTICS
7.1 Mating/Unmating Force – The force to mate a receptacle connector and compatible header shall not
exceed 6.94N [25 ounce] per power contact and 0.97N [3.5 ounce] per signal contact. The unmating
force shall not be less than 2.23N [8 ounce] per power contact and 0.18N [0.64 ounce] per signal
contact. The following details shall apply:
Table 2: Mating/Unmating Force
Force spec. Power contact Signal contact
Mating force Maximum 6.94N [25 ounce] 0.97N [3.5 ounce]
Unmating force Minimum 2.23N [8 ounce] 0.18N [0.64 ounce]
a. Cross Head Speed – 25.4mm [1 inch] per minute
b. Lubrication – None
c. Utilize free floating fixtures
d. Reference EIA 364-13
7.2 Normal Force – The contact normal force shall not be less than 350 grams per beam for the power
contacts and 50 grams (nor greater than 120 grams) per beam for the signal contacts when tested in
accordance with FCI Test Specification BUS-03-404.
PDS: Rev :AA STATUS:Released Printed: Jul 29, 2016
NUMBER GS-12-149
TYPE PRODUCT SPECIFICATION
TITLE PAGE REVISION
PwrBlade ® Product Specification 5 of 13 AA
AUTHORIZED BY DATE
MT Ruan 29 Jul 16
CLASSIFICATION
UNRESTRICTED
Copyright FCI
Form E-3334
Rev F
GS-01-001
7.3 Contact Retention – Individual power and signal contacts shall withstand an axial retention load of
13.4N [3 pound]. Individual signal receptacle contacts will withstand an axial load of 26.7N [6 pound]
minimum to seat further into housing.
a. Rate of 12.7mm [0.5 inch] per minute without dislodging from the housing cavity.
b. Test 30 contacts
c. As per MIL-STD-1344A, Method 2007.1.
7.4 Individual Pin Insertion/Retention Force - The force required to insert an individual compliant pin into
a plated through hole in a printed circuit board at a rate of 5.08mm [0.2 inch] per minute shall not
exceed 26.6N [6 pound] for signal receptacle contacts, 93.4N [21 pound] for signal header pins and
111.2N [25 pound] per tail for power contacts . The retention force in the axial direction opposite that
of insertion shall not be less than 6.7N [1.5 pound] for signal receptacle contacts, 13.4N [3 pound] for
signal header pins and 22.3N [5 pound] per tail for power contacts.
Table 3: Individual Pin Insertion/Retention Force table
Force spec. Pwr contact
(per tail) Signal contact
Rec Signal contact Hdr Signal contact
Insertion force Maximum 111.2N [25lbs] 26.6N [6lbs] 93.4N [21lbs]
Retention force Minimum 22.3N [5lbs] 6.7N [1.5lbs] 13.4N [3lbs]
7.5 PCB Hole Deformation Radius
Power Contacts – cross-section parallel to board surface. Photograph and measure the hole
deformation (deformation on board material) radius at a point 0.254mm [0.010”] from the surface, and
the center of the compliant pin section. Include 10 holes. The average (of 10 holes) hole deformation
radius shall be no greater than0.0381mm [0.0015”] when measured from the drilled hole. The
absolute maximum deformation radius shall not exceed 0.0508mm [0.002”].
Signal Contacts
Signal Receptacle Contacts – Reference FCI BUS-12-111 – HPC Solderless (Press Fit) Right Angle
Receptacles
Signal Header Contacts – Same as the requirement for Power Contacts above
7.6 PCB Hole Wall Damage – Cross-section perpendicular to the board surface, and through the
compliant section wear track. Photograph and measure the copper thickness remaining between the
compliant section and the printed wiring board laminate. Include 10 holes. The minimum average (of
10 holes) copper thickness remaining between the compliant pin and the printed wiring board
laminate shall not be less than 0.00762mm [0.0003”]. In addition there shall be no copper cracks,
separations between conductive interfaces, or laminate-to-copper separations.
PDS: Rev :AA STATUS:Released Printed: Jul 29, 2016
NUMBER GS-12-149
TYPE PRODUCT SPECIFICATION
TITLE PAGE REVISION
PwrBlade ® Product Specification 6 of 13 AA
AUTHORIZED BY DATE
MT Ruan 29 Jul 16
CLASSIFICATION
UNRESTRICTED
Copyright FCI
Form E-3334
Rev F
GS-01-001
7.7 Board Lock Retention to Housing- Individual board locks shall withstand an axial load of 13.4N [3
pound] minimum.
Rate of 12.7mm [0.5 inch] per minute without dislodging from the housing cavity.
Test 30 board locks
ENVIRONMENTAL CONDITIONS
After exposure to the following environmental conditions in accordance with the specified test procedure and /
or details, the product shall show no physical damage and shall meet the applicable electrical and mechanical
requirements of paragraphs 6.0 and 7.0 as detailed in Table 1 test sequences. Unless otherwise specified,
assemblies shall be mated during exposure.
8.1 Thermal Shock – EIA 364 TP 32
a. Test condition – 36 cycles
b. Temperature Range – -55 to +125 o C
c. Time at Each Temperature – To refer to EIA 364 TP 32 based on product mass
d. Transfer Time – 5 minutes, maximum
8.2 Humidity, Steady State – EIA 364 TP 31, Method II
a. Relative Humidity – 95%
b. Temperature – +40 o C
c. Test Duration – 96 hours
8.3 High Temperature Life, EIA 364 TP 17
a. Test Duration – 21 Days
b. Temperature – +125 o C
c. Pre-condition – Perform number of durability cycles specified for product
8.4 Environmental Sequence:
Phase I – Thermal Shock, EIA 364-32
a. Test Duration – 36 cycles
b. Temperature Range – Between -55 and +125 o C
c. Time at Each Temperature – To refer to EIA 364-32 based on product mass
d. Transfer Time – 5 minutes, maximum
Phase II – Humidity, EIA 364-31, Method II
a. Test Duration – 10 days
b. Relative Humidity – 95%
PDS: Rev :AA STATUS:Released Printed: Jul 29, 2016
NUMBER GS-12-149
TYPE PRODUCT SPECIFICATION
TITLE PAGE REVISION
PwrBlade ® Product Specification 7 of 13 AA
AUTHORIZED BY DATE
MT Ruan 29 Jul 16
CLASSIFICATION
UNRESTRICTED
Copyright FCI
Form E-3334
Rev F
GS-01-001
c. Temperature – +40 o C
Phase III – High Temperature Life, EIA 364-17
a. Test Duration – 21days
b. Temperature – +125 o C
c. Pre-condition – Perform number of durability cycles specified for product
8.5 Industrial Mixed Flowing Gas (IMFG) – EIA 364-65
a. Class – IIA
b. Duration – 20 days
c. Mated
d. Test contact resistance after 10 and 20 days
8.6 Vibration Sinusoidal – EIA 364 TP 28
a. Condition – III
b. Vibration Amplitude – 1.524mm [0.06”] DA or 15G
c. Frequency Range – 10 to 2000 to 10 Hz
d. Sweep Time and Duration – 20 minutes per cycle, 4 hours along each of three orthogonal
axes (12 hours total)
e. Mounting – rigidly mount assemblies
f. No Discontinuities of greater than 10 nano-seconds
8.7 Mechanical Shock – EIA 364-27
a. Condition A (50G, 11 millisecond half sine wave)
b. Shocks – 3 shocks in both directions along each of three orthogonal axes (18 total)
c. Mounting – rigidly mount assemblies
d. No discontinuities of greater than 10 nano-seconds
8.8 Durability – Standard laboratory procedure as applicable to the specific product
a. Number of Cycles – 200
b. Cycling rate – 127mm [5 inch] per minute
8.9 Solderability – ANSI-J-002, Test Condition A
a. Steam aging – 4 hours
b. Pcb termination area was evaluated and meets the requirements of ANSI-J-002.
8.10 Resistance to Solder Heat – EIA 364-56
a. Test Condition – E
b. There shall be no evidence of physical or mechanical damage.
PDS: Rev :AA STATUS:Released Printed: Jul 29, 2016
NUMBER GS-12-149
TYPE PRODUCT SPECIFICATION
TITLE PAGE REVISION
PwrBlade ® Product Specification 8 of 13 AA
AUTHORIZED BY DATE
MT Ruan 29 Jul 16
CLASSIFICATION
UNRESTRICTED
Copyright FCI
Form E-3334
Rev F
GS-01-001
8.11 Operating temperature – -55 o C to 125 o C
9.0 QUALITY ASSURANCE PROVISIONS
9.1 Equipment Calibration
All test equipment and inspection facilities used in the performance of any test shall be maintained in
a calibration system in accordance with ISO 9000
9.2 Inspection conditions
Unless otherwise specified, all inspections shall be performed under the following conditions:
a. Temperature: 25 +/- 5o C
b. Relative humidity: 30 to 60%
c. Barometric Pressure: Local ambient
PDS: Rev :AA STATUS:Released Printed: Jul 29, 2016
NUMBER GS-12-149
TYPE PRODUCT SPECIFICATION
TITLE PAGE REVISION
PwrBlade ® Product Specification 9 of 13 AA
AUTHORIZED BY DATE
MT Ruan 29 Jul 16
CLASSIFICATION
UNRESTRICTED
Copyright FCI
Form E-3334
Rev F
GS-01-001
9.3 Sample Quality and Description
R/A Header P/N 51720, Vertical Receptacle P/N 51740 and R/A Receptacle P/N 51760
P/N
For lead free test,
use 517*0 - ********LF Type 1 2 3 4 5 6 7 8 9 10 11 12 13 14
51720-11008410AA_ _ Ass’y 6 3 O 6 6 3 3 O 6 2 3 3 0 0
51740-11008410AA_ _ Ass’y 0 3 M 0 0 0 0 M 0 0 0 0 0 0
51740-11008410CC_ _ Ass’y 3 0 I 3 3 0 3 I 3 0 0 0 9 0
51760-11008410AA_ _ Ass’y 3 0 T 3 3 3 0 T 3 2 3 3 0 12
SK-44146-002 PCB 0 0 T 0 0 0 0 T 0 0 0 0 0 0
SK-44147-002 PCB 0 0 E 0 0 0 0 E 0 0 0 0 9 0
SK-44148-002 PCB 0 0 D 0 0 0 0 D 0 0 0 0 0 0
SK-44146-012 PCB 6 3 6 0 3 3 6 0 0 0 0 0
SK-44147-012 PCB 3 3 3 0 0 3 3 0 0 0 9 0
SK-44148-012 PCB 3 0 3 0 3 0 3 0 0 0 0 0
Vertical Header P/N 51700, R/A Receptacle Press Fit P/N 51866 and Vertical Receptacle P/N 51740 (mated to
51700 for qualification testing)
P/N
For lead free test,
use 517*0 -
********LF
Type 1 2 3 4 5 6 7 8 9 11 12 13 14
51546-001021_ _ contact O O O O 12
51700-11008410AA_ _ Ass’y 3 M M 3 M 4 M 3
51700-11008410CC_ _ Ass’y 3 I 3 I 6 I 4 I
SK-44145-002 (2 oz) PCB T T T 2 2 T
SK-44145-012 (5 oz) PCB 3 3 E 3 E 3 6 E 2 2 E 1
51866-002_ _ Ass’y 3 3 D 3 D D 4 D
51740-1108410AA_ _ Ass’y 3 6 4
SK-44148-002 (2 oz) PCB 2
SK-44148-012 (5 oz) PCB 3 3 2
SK-44147-002 (2 oz) PCB 2
SK-44147-012 (5 oz) PCB 3 6 2
PDS: Rev :AA STATUS:Released Printed: Jul 29, 2016
NUMBER GS-12-149
TYPE PRODUCT SPECIFICATION
TITLE PAGE REVISION
PwrBlade ® Product Specification 10 of 13 AA
AUTHORIZED BY DATE
MT Ruan 29 Jul 16
CLASSIFICATION
UNRESTRICTED
Copyright FCI
Form E-3334
Rev F
GS-01-001
9.4 Acceptance
9.4.1 Electrical and Mechanical requirements shall be as indicated in Paragraphs 6.0 and 7.0 using
test data and appropriate statistical techniques.
9.4.2 Failures attributed to equipment, test setup or operator error shall not disqualify the
product.
9.5 Qualification Testing
Qualification testing shall be performed on sample units predicted with equipment and procedures
normally used in production. Test sequence is as shown in Table 1.
9.6 Re-qualification Testing
If any of the following conditions occur, the responsible product engineer shall initiate re-qualification
testing consisting of the applicable parts of the test matrix, Table 1.
a. A significant design change is made to the existing product that impacts the product form, fit
or function. Examples of significant changes shall include, but not be limited to, changes in
the plating material composition or thickness, contact force or contact surface geometry,
insulator design, contact base material or contact lubrication requirements.
b. A significant event occurs during production or end use requiring corrective action to be taken
relative to the product design or manufacturing process.
c. A significant change is made to the manufacturing process that impacts the product form, fit
or function.
PDS: Rev :AA STATUS:Released Printed: Jul 29, 2016
NUMBER GS-12-149
TYPE PRODUCT SPECIFICATION
TITLE PAGE REVISION
PwrBlade ® Product Specification 11 of 13 AA
AUTHORIZED BY DATE
MT Ruan 29 Jul 16
CLASSIFICATION
UNRESTRICTED
Copyright FCI
Form E-3334
Rev F
GS-01-001
Test Sequence Table 3
Test Group
Test 1 2 3 4 5 6 7 8 9 10 11 12 13 14
PAR Test Sequence
Examination of Product
5.5
1
20 1
12 O
M 1
8 1
8 1
3 1
8 O
M 1
3 1
3 1 1
3 1
13 1
3
Contact Resistance
Low Level
6.1
3
6
9
14
17
3
6
10
I
T
T
E
D
2
6
2
6 I
T
T
E
D
3
6
9
Contact Resistance
At specified current 6.2 4
7
10
15
18
4
7
11
3
7
3
7
Insulation Resistance 6.3 2
6
Dielectric Withstanding
Voltage 6.4 3
7
Current Rating 6.5 2
Mating/Unmating Force
7.1
2
11
13
19
2
8
Normal Force 7.2 2
Contact Insertion/ Retention 7.3 2
Individual Pin Insertion
(new pin for each insertion) 7.4 2
5
8
Individual Pin Retention 7.4 4
7
10
PCB Hole Deformation Radius 7.5 11
PCB Hole Wall Damage 7.6 12
Board Lock Retention 7.7 2
Thermal Shock 8.1 4
Humidity, Steady State 8.2 5
Hi Temperature Life 8.3 5
Environmental Sequence 8.4
Phase I 5
Phase II 8
Phase III 16
Ind. Mixed Flowing Gas 8.5 9
Vibration 8.6 4
Mechanical Shock 8.7 5
Durability 8.8 12 5 4
Solderability 8.9 2
Res. To Soldering Heat 8.10 2
PDS: Rev :AA STATUS:Released Printed: Jul 29, 2016
NUMBER GS-12-149
TYPE PRODUCT SPECIFICATION
TITLE PAGE REVISION
PwrBlade ® Product Specification 12 of 13 AA
AUTHORIZED BY DATE
MT Ruan 29 Jul 16
CLASSIFICATION
UNRESTRICTED
Copyright FCI
Form E-3334
Rev F
GS-01-001
REVISION RECORD
REV PAGE DESCRIPTION EC# DATE
A ALL New release V10892 02/22/01
B 2,12,14,16,
17
Update to include R/A Receptacle press fit
Revise test groups and sequences to reflect actual
test procedures
V11528 05/02/01
C ALL Update to include vertical header
Remove test group 8
V12261 09/24/01
D 5 & 6 Correct test procedure numbering V12530 11/14/01
E 1, 2, 4, 6, 7,
9 Added reference to HPC product specification
Added/deleted referenced lab reports to make current
Added vertical header signal contact press fit values
Added vertical header and R/A receptacle press fit
test sample table
Corrected paragraph numbering in test sequence
table; Added Areva log
V20869 05/2/02
F 2
3
4
Add HPC press fit specifications references
Add P/N 51866 to paragraph 5.4.1
Include min. 6# to seat signal receptacle contacts
further into housing.
Revised Section 7.5 to include references to HPC
specifications
V21237 8/05/02
G 7 Increase durability rating to 200 cycles V21408 8/29/02
H 1
3
9
All
4.1.1 Add more typical P/N series: 51939, 51940,
51897, 51921 etc.
5.3 Update the finish for Powerblade all series
9.3 Add the test samples P/N for Lead Free parts, in
the table” For lead free test, use 517*0 - ********LF”
Change the “FCI” logo
DG06-0223 6/02/06
J 3 & 7
5
6
Update dwell time for 8.1 and phase 1 in 8.4
Update insertion / retention force for signal header
pins (7.4)
Update hole deformation radius for signal header pins
(7.5)
DG06-0400 12/13/06
K 5 Update to clarify para. 6.5 by a clearer description DG07-0002 1/4/07
L 2 Remove referenced FCI spec. GS-12-005: Split-Lif
Compliant and FCI Lab Reports. (4.4.5 & 4.5) DG07-0323 8/08/07
PDS: Rev :AA STATUS:Released Printed: Jul 29, 2016
NUMBER GS-12-149
TYPE PRODUCT SPECIFICATION
TITLE PAGE REVISION
PwrBlade ® Product Specification 13 of 13 AA
AUTHORIZED BY DATE
MT Ruan 29 Jul 16
CLASSIFICATION
UNRESTRICTED
Copyright FCI
Form E-3334
Rev F
GS-01-001
M
N
5 & 8
3 & 8 & 11
Update to clarify the retention force of power pin by a
clearer description. (7.4)
Change operating temperature range. (8.11)
Add GXT plating option on contact area. (5.3)
Correct operating temperature range. (8.11)
Correct the test sequence in test group 1.
DG07-0420
DG08-0022
10/23/07
01/21/08
P 3 Remove Gold Flash plating option on tail area. (5.3) DG08-0187 07/22/08
R 3 Remove GXT plating option on contact area for
Signal contact. (5.3) DG08-0226 08/19/08
S 2 & 3 Modify item 4.1 drawing number & 5.3 add plating
spec. 10092675 DG08-0255 10/02/08
T 7 Change operating temperature range. (8.11) DG10-0162 05/04/10
U
2 & 3 Remove PwrBlade Qualification Summary GS-29-
149. (4.4.1)
Re-describe raw materials of Power and Signal
contacts. (5.2)
Remove plating specification 10092675. (5.3)
Tighten Contact Resistance spec. of Power contacts
from 2.0 milliohm max. to 0.7 milliohm max..
DG10-0205 06/02/10
V 1, 4, 6,7,10 Add a new table for Individual Pin Insertion/Retention
Force.(7.4)
Change operation temperature range.(8.11)
DG-13984-1 03/27/13
W ALL Correct print error DG-14425-1 04/07/13
X 3,5,6,7 Update operating temperature DG-16432-1 03/04/14
Y 4
ALL
Update current rating (6.5)
Update logo
DG-23359 02/25/16
AA 4 Update current rating of signal contact (6.5) DG-24556 07/29/16
PDS: Rev :AA STATUS:Released Printed: Jul 29, 2016
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
FCI / Amphenol:
51624-XX001LF 51721-10002406AALF 51700-11102003AALF 51721-10002406ABLF 51744-10202402A0LF
51742-10202400CCLF 51416-001LF 51704-10202402A0LF 51866-008LF 51415-001LF 51625-XX001LF 51742-
10302400CCLF 51720-10402002AALF 51740-11102003AALF 51720-10202402AALF 51720-10602804ABLF 51760-
10602804ABLF 51261-XX001LF 51617-XX002LF 51666-001LF 51667-XX001LF 51700-10104801AALF 51700-
10106001AALF 51700-10201602CCLF 51700-10202402AALF 51700-10402404AALF 51700-10403204CALF 51700-
10602406CALF 51701-10002408CCLF 51701-10003208CCLF 51703-10400000CCLF 51704-10206002A0LF 51720-
10002004AALF 51720-10101201AALF 51720-10101601AALF 51720-10102401AALF 51720-10103201ABLF 51720-
10106001AALF 51720-10106001ABLF 51720-10201202ABLF 51720-10202403AALF 51720-10202404AALF 51720-
10203202AALF 51720-10203206AALF 51720-10204802AALF 51720-10208002AALF 51720-10300803AALF 51720-
10301203AALF 51720-10301603ABLF 51720-10302003AALF 51720-10302403AALF 51720-10302406AALF 51720-
10312803ABLF 51720-10400804AALF 51720-10401204AALF 51720-10402402AALF 51720-10402404AALF 51720-
10402404ABLF 51720-10402406AALF 51720-10402406ABLF 51720-10410004AALF 51720-10500805AALF 51720-
10502405AALF 51720-10602406AALF 51720-10602807ABLF 51720-10701607ABLF 51720-10702407AALF 51720-
10702807ABLF 51720-10703206AALF 51720-10802408AALF 51720-10803208AALF 51720-11102003AALF 51721-
10000807AALF 51721-10001608AALF 51721-10002408ABLF 51721-10002410AALF 51721-10002414AALF 51721-
10004808ABLF 51722-10103600AALF 51722-10302400AALF 51722-10401600AALF 51722-10402400AALF 51722-
10502400AALF 51722-10600800AALF 51722-10602000AALF 51722-10603600AALF 51722-10702400AALF 51722-
10802400AALF 51722-10802400ABLF 51722-10901600AALF 51722-11103200AALF 51722-11202000AALF 51722-
11402400AALF 51722-12002000ABLF 51723-10300000AALF 51723-10400000AALF 51723-10700000AALF 51723-
10800000AALF 51723-10900000AALF 51723-11600000AALF