TS117L Multifunction Telecom Switch INTEGRATED CIRCUITS DIVISION Parameter Blocking Voltage Load Current On-Resistance (max) Rating 350 120 35 Units VP mArms / mADC Features * Current-Limited Relay * 3750Vrms Input/Output Isolation * Low Drive Power Requirements (TTL/CMOS Compatible) * FCC Compatible * VDE Compatible * No Moving Parts * High Reliability * Arc-Free With No Snubbing Circuits * No EMI/RFI Generation * Small 8-Pin Package * Machine Insertable, Wave Solderable * Surface Mount and Tape & Reel Versions Available Applications * Telecommunications * Telecom Switching * Tip/Ring Circuits * Modem Switching (Laptop, Notebook, Pocket Size) * Hook Switch * Dial Pulsing * Ground Start * Ringing Injection * Instrumentation * Multiplexers * Data Acquisition * Electronic Switching * I/O Subsystems * Meters (Watt-Hour, Water, Gas) * Medical Equipment-Patient/Equipment Isolation * Security * Aerospace * Industrial Controls Description The TS117L integrated circuit device combines a current-limited, 350V, normally open (1-Form-A) relay and an optocoupler in a single package. The relay uses optically coupled MOSFET technology to provide 3750Vrms of input to output isolation. Its optically coupled relay outputs, which use the patented OptoMOS architecture, are controlled by a highly efficient GaAIAs infrared LED. The TS117L enables telecom circuit designers to combine two discrete functions in a single component that uses less space than traditional discrete component solutions. Approvals * UL Recognized Component: File E76270 * CSA Certified Component: Certificate 1175739 * EN/IEC 60950 Certified Component: TUV Certificate: B 10 05 49410 006 Ordering Information Part # TS117L TS117PL TS117PLTR TS117LS TS117LSTR Description 8-Pin DIP (50/Tube) 8-Pin Flatpack (50/Tube) 8-Pin Flatpack (1000/Reel) 8-Pin Surface Mount (50/Tube) 8-Pin Surface Mount (1000/Reel) Pin Configuration + LED - Relay - LED - Relay Collector - Phototransistor Emitter - Phototransistor 1 8 2 7 3 6 4 5 Load - Relay (MOSFET Output) Load - Relay (MOSFET Output) LED - Phototransistor -/+ LED - Phototransistor +/- Switching Characteristics of Normally Open Devices Form-A IF 90% 10% ILOAD ton Pb DS-TS117L-R06 toff e3 www.ixysic.com 1 INTEGRATED CIRCUITS DIVISION TS117L Absolute Maximum Ratings @ 25C Parameter Blocking Voltage Input Power Dissipation 1 Input Control Current, Relay Peak (10ms) Reverse Input Voltage Input Control Current, Detector Total Power Dissipation 2 Isolation Voltage, Input to Output Operational Temperature Storage Temperature 1 Derate linearly 1.33 mW / C 2 Derate linearly 6.67 mW / C Ratings 350 150 50 1 5 100 800 3750 -40 to +85 -40 to +125 Absolute Maximum Ratings are stress ratings. Stresses in excess of these ratings can cause permanent damage to the device. Functional operation of the device at conditions beyond those indicated in the operational sections of this data sheet is not implied. Units VP mW mA A V mA mW Vrms C C Electrical Characteristics @25C: Relay Section Parameter Output Characteristics Load Current, Continuous Load Current Limit On-Resistance Off-State Leakage Current Switching Speeds Turn-On Turn-Off Output Capacitance Input Characteristics Input Control Current to Activate Input Control Current to Deactivate Input Voltage Drop Reverse Input Current Common Characteristics Input to Output Capacitance Conditions Symbol Min Typ Max Units IL=120mA VL=350V IL ICL RON ILEAK 130 - 170 30 - 120 210 35 1 mArms / mADC mA VL=50V, f=1MHz ton toff COUT - 25 3 3 - ms ms pF IL=120mA IF=5mA VR=5V IF IF VF IR 0.4 0.9 - 0.7 1.2 - 2 1.4 10 mA mA V A - CI/O - 3 - pF IF=5mA, VL=10V A Electrical Characteristics @25C: Detector Section Parameter Output Characteristics Phototransistor Blocking Voltage Phototransistor Dark Current Saturation Voltage Current Transfer Ratio Input Characteristics Input Control Current Input Voltage Drop Input Current (Detector Must be Off) Isolation, Input to Output 2 Conditions Symbol Min Typ Max Units IC=10A VCE=5V, IF=0mA IC=2mA, IF=16mA IF=6mA, VCE=0.5V BVCEO ICEO VSAT CTR 20 33 50 50 0.3 100 500 0.5 - V nA V % IC=2mA, VCE=0.5V IF=5mA IC=1A, VCE=5V - IF VF IF VI/O 0.9 5 3750 2 1.2 25 - 6 1.4 - mA V A Vrms www.ixysic.com R06 INTEGRATED CIRCUITS DIVISION TS117L RELAY PERFORMANCE DATA @25C (Unless Otherwise Noted)* 30 30 20 15 10 Device Count (N) 25 20 15 10 5 5 0 25 1.4875 1.6125 1.7375 25 20 15 10 5 0 0 1.3625 1.8625 0.15 0.25 0.35 0.45 0.55 0.65 0.025 0.075 0.125 0.175 0.225 0.275 0.325 0.75 LED Forward Voltage Drop (V) Turn-On Time (ms) Turn-Off Time (ms) Typical IF for Switch Operation (N=50, IL=120mADC) Typical IF for Switch Dropout (N=50, IL=120mADC) Typical On-Resistance Distribution (N=50, IF=2mA, IL=120mADC) 25 20 Device Count (N) Device Count (N) 35 25 Device Count (N) Device Count (N) 30 Typical Turn-Off Time (N=50, IF=2mA, IL=120mADC) Typical Turn-On Time (N=50, IF=2mA, IL=120mADC) 15 10 5 0 35 30 20 Device Count (N) 35 Typical LED Forward Voltage Drop (N=50, IF=5mA) 15 10 5 0.75 1.05 1.35 1.65 1.95 20 15 10 5 0 0 0.45 25 0.45 2.25 0.75 1.05 1.35 1.65 1.95 17.0 2.25 17.4 17.8 18.2 18.6 19.0 On-Resistance (:) LED Current (mA) LED Current (mA) Typical Blocking Voltage Distribution (N=50) 35 Device Count (N) 30 25 20 15 10 5 0 376.25 382.75 389.25 395.75 402.25 408.75 415.25 Blocking Voltage (VP) Typical Turn-On Time vs. LED Forward Current (IL=120mADC) 0.9 1.8 1.4 IF=50mA IF=30mA IF=20mA IF=10mA IF=5mA 1.2 1.0 0.8 0.35 0.7 Turn-Off Time (ms) 1.6 0.6 0.5 0.4 0.3 0.2 -20 0 20 40 60 Temperature (C) 80 100 120 0.30 0.25 0.20 0.15 0.10 0.05 0.1 0 0 -40 Typical Turn-Off Time vs. LED Forward Current (IL=120mADC) 0.40 0.8 Turn-On Time (ms) LED Forward Voltage Drop (V) Typical LED Forward Voltage Drop vs. Temperature 0 5 10 15 20 25 30 35 40 LED Forward Current (mA) 45 50 0 5 10 15 20 25 30 35 40 45 50 LED Forward Current (mA) * The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our application department. R06 www.ixysic.com 3 INTEGRATED CIRCUITS DIVISION TS117L RELAY PERFORMANCE DATA @25C (Unless Otherwise Noted)* Typical Turn-On Time vs. Temperature (IL=120mADC) 1.2 1.0 0.8 0.6 IF=5mA IF=10mA IF=20mA 0.4 0.2 0.5 IF=2mA 0.4 0.3 0.2 IF=5mA 0.1 -40 -20 0 20 40 60 80 100 120 Typical IF for Switch Operation vs. Temperature (IL=120mADC) 30 20 -20 0 20 40 60 80 -40 100 100 0.5 Load Current (mA) 150 1.0 2.5 2.0 1.5 1.0 0 -20 0 20 40 60 80 3 4 50 0 -50 -20 0 20 40 60 80 100 -4 -3 -2 -1 0 1 2 Temperature (C) Load Voltage (V) Maximum Load Current vs. Temperature Typical Blocking Voltage vs. Temperature Typical Leakage vs. Temperature Measured across Pins 7&8 Blocking Voltage (VP) 160 140 120 100 IF=10mA IF=5mA IF=2mA 80 60 40 20 0 420 0.014 410 0.012 400 390 380 370 0 20 40 60 80 100 -40 120 -20 0 0.008 0.006 20 40 60 80 0.002 -40 100 -20 0 Temperature (C) Temperature (C) 40 60 80 100 400 350 300 Current (mA) 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 10Ps 100Ps 1ms 10ms 100ms 20 Temperature (C) Typical Current Limiting vs. Temperature Energy Rating Curve Load Current (A) 0.010 0.004 360 -20 100 Temperature (C) 180 -40 80 -150 -40 100 Leakage (PA) -40 60 -100 0.5 0 40 Typical Load Current vs. Load Voltage (IF=2mA) 3.0 1.5 20 Typical IF for Switch Dropout vs. Temperature (IL=120mADC) 3.5 2.0 0 Temperature (C) 3.0 2.5 -20 Temperature (C) 3.5 LED Current (mA) LED Current (mA) 40 0 -40 Temperature (C) Load Current (mA) 50 10 0 0 Typical On-Resistance vs. Temperature (IF=2mA, IL=120mADC) 60 0.6 Turn-Off Time (ms) Turn-On Time (ms) 0.7 IF=2mA 1.4 On-Resistance (:) 1.6 Typical Turn-Off Time vs. Temperature (IL=120mADC) 250 200 150 100 50 0 1s 10s 100s -40 -20 0 20 40 60 80 100 Temperature (C) Time * The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our application department. 4 www.ixysic.com R06 INTEGRATED CIRCUITS DIVISION TS117L DETECTOR PERFORMANCE DATA @25C (Unless Otherwise Noted)* 8 4.0 7 3.5 3.0 2.5 2.0 1.5 1.0 6 5 4 2 1 0 0 4 6 8 10 12 14 Forward Current (mA) 16 18 20 IF=1mA IF=2mA IF=5mA IF=10mA IF=15mA IF=20mA 3 0.5 2 12 -40 -20 0 20 40 60 80 Temperature (C) 100 120 Collector Current (mA) 4.5 0 Typical Collector Current vs. Forward Current (VCE=0.5V) Typical Normalized CTR vs. Temperature (VCE=0.5V) Normalized CTR (%) Normalized CTR (%) Typical Normalized CTR vs. Forward Current (VCE=0.5V) 10 8 6 4 2 0 0 2 4 6 8 10 12 14 16 18 20 Forward Current (mA) * The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our application department. R06 www.ixysic.com 5 INTEGRATED CIRCUITS DIVISION TS117L Manufacturing Information Moisture Sensitivity All plastic encapsulated semiconductor packages are susceptible to moisture ingression. IXYS Integrated Circuits Division classified all of its plastic encapsulated devices for moisture sensitivity according to the latest version of the joint industry standard, IPC/JEDEC J-STD-020, in force at the time of product evaluation. We test all of our products to the maximum conditions set forth in the standard, and guarantee proper operation of our devices when handled according to the limitations and information in that standard as well as to any limitations set forth in the information or standards referenced below. Failure to adhere to the warnings or limitations as established by the listed specifications could result in reduced product performance, reduction of operable life, and/or reduction of overall reliability. This product carries a Moisture Sensitivity Level (MSL) rating as shown below, and should be handled according to the requirements of the latest version of the joint industry standard IPC/JEDEC J-STD-033. Device Moisture Sensitivity Level (MSL) Rating TS117L / TS117PL / TS117LS MSL 1 ESD Sensitivity This product is ESD Sensitive, and should be handled according to the industry standard JESD-625. Reflow Profile This product has a maximum body temperature and time rating as shown below. All other guidelines of J-STD-020 must be observed. Device Maximum Temperature x Time TS117L / TS117LS 250C for 30 seconds TS117PL 260C for 30 seconds Board Wash IXYS Integrated Circuits Division recommends the use of no-clean flux formulations. However, board washing to remove flux residue is acceptable. Since IXYS Integrated Circuits Division employs the use of silicone coating as an optical waveguide in many of its optically isolated products, the use of a short drying bake could be necessary if a wash is used after solder reflow processes. Chlorine- or Fluorine-based solvents or fluxes should not be used. Cleaning methods that employ ultrasonic energy should not be used. Pb 6 e3 www.ixysic.com R06 INTEGRATED CIRCUITS DIVISION TS117L Mechanical Dimensions TS117L 2.540 0.127 (0.100 0.005) 9.652 0.381 (0.380 0.015) 8-0.800 DIA. (8-0.031 DIA.) 2.540 0.127 (0.100 0.005) 9.144 0.508 (0.360 0.020) 6.350 0.127 (0.250 0.005) Pin 1 PCB Hole Pattern 7.620 0.254 (0.300 0.010) 6.350 0.127 (0.250 0.005) 3.302 0.051 (0.130 0.002) 0.457 0.076 (0.018 0.003) 7.620 0.127 (0.300 0.005) 7.239 TYP. (0.285) 4.064 TYP (0.160) 7.620 0.127 (0.300 0.005) 0.254 0.0127 (0.010 0.0005) Dimensions mm (inches) 0.813 0.102 (0.032 0.004) TS117PL 0 MIN / 0.102 MAX (0 MIN / 0.004 MAX) 2.540 0.127 (0.100 0.005) 6.350 0.127 (0.250 0.005) 7.620 0.254 (0.300 0.010) 9.398 0.127 (0.370 0.005) Pin 1 2.286 MAX. (0.090 MAX.) 2.54 (0.10) 0.635 0.127 (0.025 0.005) 8.70 (0.3425) 1.55 (0.0610) 0.203 0.013 (0.008 0.0005) 9.652 0.381 (0.380 0.015) PCB Land Pattern 0.65 (0.0255) 2.159 0.025 (0.085 0.001) 0.457 0.076 (0.018 0.003) 0.864 0.120 (0.034 0.004) Dimensions mm (inches) TS117LS 9.652 0.381 (0.380 0.015) 2.540 0.127 (0.100 0.005) 6.350 0.127 (0.250 0.005) Pin 1 0.635 0.127 (0.025 0.005) 3.302 0.051 (0.130 0.002) 9.525 0.254 (0.375 0.010) 0.457 0.076 (0.018 0.003) PCB Land Pattern 2.54 (0.10) 8.90 (0.3503) 1.65 (0.0649) 7.620 0.254 (0.300 0.010) 0.254 0.0127 (0.010 0.0005) 0.65 (0.0255) 4.445 0.127 (0.175 0.005) Dimensions mm (inches) 0.813 0.102 (0.032 0.004) R06 www.ixysic.com 7 INTEGRATED CIRCUITS DIVISION TS117L TS117LSTR Tape & Reel 330.2 DIA. (13.00 DIA.) Top Cover Tape Thickness 0.102 MAX. (0.004 MAX.) W=16.00 (0.63) Bo=10.30 (0.406) K0 =4.90 (0.193) Ao=10.30 (0.406) K1 =4.20 (0.165) Embossed Carrier Embossment P=12.00 (0.472) User Direction of Feed Dimensions mm (inches) NOTES: 1. Dimensions carry tolerances of EIA Standard 481-2 2. Tape complies with all "Notes" for constant dimensions listed on page 5 of EIA-481-2 TS117PLTR Tape & Reel 2.00 (0.079) 330.2 DIA. (13.00 DIA.) Top Cover Tape Thickness 0.102 MAX. (0.004 MAX.) Embossment W = 16.00 (0.63) 7.50 (0.295) Bo = 10.30 (0.406) K0 = 2.70 (0.106) K1 = 2.00 (0.079) Embossed Carrier 4.00 (0.157) P = 12.00 (0.472) User Direction of Feed Ao = 10.30 (0.406) Dimensions mm (inches) NOTES: 1. All dimensions carry tolerances of EIA Standard 481-2 2. The tape complies with all "Notes" for constant dimensions listed on page 5 of EIA-481-2 For additional information please visit our website at: www.ixysic.com IXYS Integrated Circuits Division makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications and product descriptions at any time without notice. Neither circuit patent licenses nor indemnity are expressed or implied. Except as set forth in IXYS Integrated Circuits Division's Standard Terms and Conditions of Sale, IXYS Integrated Circuits Division assumes no liability whatsoever, and disclaims any express or implied warranty, relating to its products including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual property right. The products described in this document are not designed, intended, authorized or warranted for use as components in systems intended for surgical implant into the body, or in other applications intended to support or sustain life, or where malfunction of IXYS Integrated Circuits Division's product may result in direct physical harm, injury, or death to a person or severe property or environmental damage. IXYS Integrated Circuits Division reserves the right to discontinue or make changes to its products at any time without notice. 8 Specification: DS-TS117L-R06 (c)Copyright 2013, IXYS Integrated Circuits Division All rights reserved. Printed in USA. 6/20/2013