ISL28148, ISL28248, ISL28448 (R) Data Sheet September 21, 2010 4.5MHz, Single Dual and Quad Precision Rail-to-Rail Input-Output (RRIO) Op Amps with Very Low Input Bias Current The ISL28148, ISL28248 and ISL28448 are 4.5MHz low-power single, dual and quad operational amplifiers. The parts are optimized for single supply operation from 2.4V to 5.5V, allowing operation from one lithium cell or two Ni-Cd batteries. The single, dual and quad feature an Input Range Enhancement Circuit (IREC) which enables them to maintain CMRR performance for input voltages greater than the positive supply. The input signal is capable of swinging 0.25V above the positive supply and to 100mV below the negative supply with only a slight degradation of the CMRR performance. The output operation is rail-to-rail. The parts draw minimal supply current (900A per amplifier) while meeting excellent DC accuracy, AC performance, noise and output drive specifications. The ISL28148 features an enable pin that can be used to turn the device off and reduce the supply current to a maximum of 16A. Operation is guaranteed over -40C to +125C temperature range. FN6337.4 Features * 4.5MHz gain bandwidth product * 900A supply current (per amplifier) * 1.8mV maximum offset voltage * 1pA typical input bias current * Down to 2.4V single supply operation * Rail-to-rail input and output * Enable pin (ISL28148 SOT-23 package only) * -40C to +125C operation * Pb-free (RoHS compliant) Applications * Low-end audio * 4mA to 20mA current loops * Medical devices * Sensor amplifiers * ADC buffers * DAC output amplifiers Ordering Information PART NUMBER (Note) PACKAGE (Pb-Free) PART MARKING PKG. DWG. # ISL28148FHZ-T7* GABT (Note 2) 6 Ld SOT-23 (Tape and Reel) P6.064A ISL28148FHZ-T7A* GABT (Note 2) 6 Ld SOT-23 (Tape and Reel) P6.064A ISL28248FBZ 28248 FBZ 8 Ld SOIC M8.15E ISL28248FBZ-T7* 28248 FBZ 8 Ld SOIC (Tape and Reel) M8.15E ISL28248FUZ 8248Z 8 Ld MSOP M8.118A ISL28248FUZ-T7* 8248Z 8 Ld MSOP (Tape and Reel) M8.118A Coming Soon, ISL28448FVZ MXZ 14 Ld TSSOP M14.173 Coming Soon, ISL28448FVZ-T7* MXZ 14 Ld TSSOP (Tape and Reel) M14.173 *Please refer to TB347 for details on reel specifications. NOTES: 1. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 2. The part marking is located on the bottom of the part. 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright (c) Intersil Americas Inc. 2007, 2008, 2010. All Rights Reserved. All other trademarks mentioned are the property of their respective owners. ISL28148, ISL28248, ISL28448 Pinouts ISL28248 (8 LD SOIC) TOP VIEW ISL28148 (6 LD SOT-23) TOP VIEW OUT 1 V- 2 + - IN+ 3 6 V+ OUT_A 1 5 EN IN-_A 2 4 IN- IN+_A 3 8 V+ 7 OUT_B - + 6 IN-_B + - V- 4 ISL28448 (14 LD TSSOP) TOP VIEW ISL28248 (8 LD MSOP) TOP VIEW OUT_A 1 8 V+ - + IN+_A 3 + - V- 4 7 OUT_B IN-_A 2 6 IN-_B IN+_A 3 5 IN+_B 14 OUT_D OUT_A 1 - + + - 11 V- V+ 4 IN+_B 5 OUT_B 7 2 10 IN+_C + - IN-_B 6 13 IN-_D 12 IN+_D - + IN-_A 2 5 IN+_B 9 IN-_C 8 OUT_C FN6337.4 September 21, 2010 ISL28148, ISL28248, ISL28448 Absolute Maximum Ratings (TA = +25C) Thermal Information Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.75V Supply Turn On Voltage Slew Rate . . . . . . . . . . . . . . . . . . . . . 1V/s Differential Input Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5mA Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5V Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . V- - 0.5V to V+ + 0.5V ESD Rating Human Body Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3kV Machine Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .300V Charged Device Model. . . . . . . . . . . . . . . . . . . . . . . . . . . . .1200V Thermal Resistance (Typical, Note 3) JA (C/W) 6 Ld SOT-23 Package . . . . . . . . . . . . . . . . . . . . . . . 230 8 Ld SO Package . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 8 Ld MSOP Package . . . . . . . . . . . . . . . . . . . . . . . . 175 14 Ld TSSOP Package . . . . . . . . . . . . . . . . . . . . . . 115 Ambient Operating Temperature Range . . . . . . . . .-40C to +125C Storage Temperature Range . . . . . . . . . . . . . . . . . .-65C to +150C Operating Junction Temperature . . . . . . . . . . . . . . . . . . . . . +125C Pb-free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . .see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. NOTE: 3. JA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details. IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests are at the specified temperature and are pulsed tests, therefore: TJ = TC = TA Electrical Specifications PARAMETER VOS V+ = 5V, V- = 0V,VCM = 2.5V, RL = Open, TA = +25C unless otherwise specified. Boldface limits apply over the operating temperature range, -40C to +125C. Temperature data established by characterization. DESCRIPTION Input Offset Voltage V OS --------------T Input Offset Voltage vs Temperature IOS Input Offset Current IB CONDITIONS MIN (Note 4) TYP MAX (Note 4) UNIT ISL28148 -1.8 -2 0 1.8 2 mV ISL28248 and ISL28448 -1.8 -2.8 0 1.8 2.8 mV 0.03 V/C -35 -80 5 35 80 pA TA = -40C to +85C -30 -80 1 30 80 pA TA = -40C to +85C Input Bias Current CMIR Common-Mode Voltage Range Guaranteed by CMRR 0 CMRR Common-Mode Rejection Ratio VCM = 0V to 5V 75 70 98 5 dB V PSRR Power Supply Rejection Ratio V+ = 2.4V to 5.5V 80 75 98 dB AVOL Large Signal Voltage Gain VO = 0.5V to 4.5V, RL = 100k to VCM 200 150 580 V/mV VO = 0.5V to 4.5V, RL = 1k to VCM 50 VOUT Maximum Output Voltage Swing Output low, RL = 100k to VCM 3 6 8 mV Output low, RL = 1k to VCM 50 70 110 mV V/mV Output high, RL = 100k to VCM 4.994 4.99 4.998 V Output high, RL = 1k to VCM 4.93 4.89 4.95 V IS,ON Quiescent Supply Current, Enabled Per Amplifier 0.9 1.25 1.4 mA IS,OFF Quiescent Supply Current, Disabled ISL28148 SOT-23 package only 10 14 16 A IO+ Short-Circuit Output Source Current RL = 10 to VCM 3 48 45 75 mA FN6337.4 September 21, 2010 ISL28148, ISL28248, ISL28448 Electrical Specifications PARAMETER V+ = 5V, V- = 0V,VCM = 2.5V, RL = Open, TA = +25C unless otherwise specified. Boldface limits apply over the operating temperature range, -40C to +125C. Temperature data established by characterization. (Continued) DESCRIPTION CONDITIONS IO- Short-Circuit Output Sink Current RL = 10 to VCM VSUPPLY Supply Operating Range V+ to V- VENH EN Pin High Level ISL28148 SOT-23 package only VENL EN Pin Low Level ISL28148 SOT-23 package only IENH EN Pin Input High Current V EN = V+, ISL28148 SOT-23 package only IENL EN Pin Input Low Current MIN (Note 4) TYP -68 2.4 MAX (Note 4) UNIT -48 -45 mA 5.5 V 2 V 0.8 V 1 1.5 1.6 A V EN = V-, ISL28148 SOT-23 package only 12 25 30 nA AC SPECIFICATIONS GBW Gain Bandwidth Product AV = 100, RF = 100k, RG = 1k, RL = 10k to VCM 4.5 MHz Unity Gain Bandwidth -3dB Bandwidth AV =1, RF = 0, VOUT = 10mVP-P, RL = 10k to VCM 13 MHz eN Input Noise Voltage Peak-to-Peak f = 0.1Hz to 10Hz 2 VPP iN Input Noise Voltage Density fO = 1kHz 28 nV/Hz Input Noise Current Density fO = 1kHz 0.016 pA/Hz VCM = 1VP-P, RL = 10k to VCM 85 dB PSRR- @ 120Hz CMRR @ 60Hz Input Common Mode Rejection Ratio Power Supply Rejection Ratio (V-) V+, V- = 1.2V and 2.5V, VSOURCE = 1VP-P, RL = 10k to VCM -82 dB PSRR+ @ 120Hz Power Supply Rejection Ratio (V+) V+, V- = 1.2V and 2.5V VSOURCE = 1VP-P, RL = 10k to VCM -100 dB 4 V/s TRANSIENT RESPONSE SR Slew Rate tr, tf, Large Signal Rise Time, 10% to 90%, VOUT AV = +2, VOUT = 3VP-P, RG = RF = 10k RL = 10k to VCM 530 ns Fall Time, 90% to 10%, VOUT AV = +2, VOUT = 3VP-P, RG = RF = 10k RL = 10k to VCM 530 ns Rise Time, 10% to 90%, VOUT AV = +2, VOUT = 10mVP-P, RG = RF = RL = 10k to VCM 50 ns Fall Time, 90% to 10%, VOUT AV = +2, VOUT = 10mVP-P, RG = RF = RL = 10k to VCM 50 ns Enable to Output Turn-on Delay Time, 10% EN = 5V to 0V, AV = +2, EN to 10% VOUT, (ISL28148) RG = RF = RL = 1k to VCM 5 s Enable to Output Turn-off Delay Time, 10% VEN = 0V to 5V, AV = +2, EN to 10% VOUT, (ISL28148) RG = RF = RL = 1k to VCM 0.2 s tr, tf, Small Signal tEN NOTE: 4. Parameters with MIN and/or MAX limits are 100% tested at +25C, unless otherwise specified. Temperature limits established by characterization and are not production tested. 4 FN6337.4 September 21, 2010 ISL28148, ISL28248, ISL28448 Typical Performance Curves V+ = 5V, V- = 0V, VCM = 2.5V, RL = Open 15 1 Rf = Rg = 100k Rf = Rg = 10k 5 0 V+ = 5V -5 RL = 1k CL = 16.3pF -10 AV = +2 VOUT = 10mVP-P -15 100 1k 10k Rf = Rg = 1k 100k 1M 10M NORMALIZED GAIN (dB) NORMALIZED GAIN (dB) 0 10 100M VOUT = 100mV -1 -2 VOUT = 50mV -3 VOUT = 10mV -4 VOUT = 1V -5 -6 V = 5V + -7 RL = 1k CL = 16.3pF -8 AV = +1 -9 1k 10k FREQUENCY (Hz) 10M 100M FIGURE 2. GAIN vs FREQUENCY vs VOUT, RL = 1k 1 1 0 0 -1 VOUT = 100mV -2 VOUT = 50mV -3 NORMALIZED GAIN (dB) NORMALIZED GAIN (dB) 1M FREQUENCY (Hz) FIGURE 1. GAIN vs FREQUENCY vs FEEDBACK RESISTOR VALUES Rf/Rg VOUT = 10mV -4 VOUT = 1V -5 -6 V+ = 5V RL = 10k CL = 16.3pF AV = +1 -7 -8 -9 1k 10k -2 VOUT = 50mV -3 VOUT = 10mV -4 1M 10M -6 -7 -9 100M VOUT = 1V -5 -8 100k VOUT = 100mV -1 V+ = 5V RL = 100k CL = 16.3pF AV = +1 1k 10k FREQUENCY (Hz) 60 -1 AV = 101 GAIN (dB) RL = 100k -3 -4 -5 -9 100M V+ = 5V VOUT = 10mVP-P CL = 16.3pF AV = +1 1k 10k AV = 1, Rg = INF, Rf = 0 AV = 10, Rg = 1k, Rf = 9.09k AV = 101, Rg = 1k, Rf = 100k AV = 1001, Rg = 1k, Rf = 1M AV = 1001 50 RL = 10k -2 -8 10M FIGURE 4. GAIN vs FREQUENCY vs VOUT, RL = 100k RL = 1k 0 -7 1M 70 1 -6 100k FREQUENCY (Hz) FIGURE 3. GAIN vs FREQUENCY vs VOUT, RL = 10k NORMALIZED GAIN (dB) 100k 40 V+ = 5V CL = 16.3pF RL = 10k VOUT = 10mVP-P 30 AV = 10 20 10 0 100k 1M 10M FREQUENCY (Hz) FIGURE 5. GAIN vs FREQUENCY vs RL 5 100M -10 100 AV = 1 1k 10k 100k 1M 10M 100M FREQUENCY (Hz) FIGURE 6. FREQUENCY RESPONSE vs CLOSED LOOP GAIN FN6337.4 September 21, 2010 ISL28148, ISL28248, ISL28448 Typical Performance Curves V+ = 5V, V- = 0V, VCM = 2.5V, RL = Open 1 V+ = 5V -1 -2 V+ = 2.4V -3 -4 -5 -6 -7 -8 RL = 10k CL = 16.3pF AV = +1 VOUT = 10mVP-P -9 10k 100k 1M 10M NORMALIZED GAIN (dB) NORMALIZED GAIN (dB) 0 100M (Continued) 8 7 6 5 4 3 2 1 0 -1 -2 -3 V+ = 5V -4 RL = 1k -5 A = +1 V -6 VOUT = 10mVP-P -7 -8 10k 100k FREQUENCY (Hz) CL = 51.7pF CL = 43.7pF CL = 37.7pF CL = 26.7pF CL = 16.7pF CL = 4.7pF 1M 10M 100M FREQUENCY (Hz) FIGURE 8. GAIN vs FREQUENCY vs CL FIGURE 7. GAIN vs FREQUENCY vs SUPPLY VOLTAGE 10 20 0 0 -10 PSRR (dB) CMRR (dB) -30 -40 -50 V+ = 2.4V, 5V RL = 1k CL = 16.3pF AV = +1 VCM = 1VP-P -60 -70 -80 -90 100 1k 10k 100k FREQUENCY (Hz) 1M -60 PSRR+ -100 -120 100 10M 20 1k 10k 100k FREQUENCY (Hz) V+, V- = 1.2V RL = 1k CL = 16.3pF AV = +1 VCM = 1VP-P 1M 10M FIGURE 10. PSRR vs FREQUENCY, V+, V- = 1.2V PSRR- -20 -40 -60 PSRR+ -80 -100 1k 10k 100k V+, V- = 2.5V RL = 1k CL = 16.3pF AV = +1 VCM = 1VP-P 1M FREQUENCY (Hz) FIGURE 11. PSRR vs FREQUENCY V+, V- = 2.5V 6 10M INPUT VOLTAGE NOISE (nV/Hz) 1000 0 PSRR (dB) -40 -80 FIGURE 9. CMRR vs FREQUENCY; V+ = 2.4V AND 5V -120 100 PSRR- -20 -20 V+ = 5V Rf = 1k Rg = 1k AV = +2 100 10 1 10 100 1k FREQUENCY (Hz) 10k 100k FIGURE 12. INPUT VOLTAGE NOISE DENSITY vs FREQUENCY FN6337.4 September 21, 2010 ISL28148, ISL28248, ISL28448 Typical Performance Curves V+ = 5V, V- = 0V, VCM = 2.5V, RL = Open (Continued) 0 0.1 -0.5 INPUT NOISE (V) INPUT CURRENT NOISE (pA/Hz) V+ = 5V Rf = 1k Rg = 1k AV = +2 -1.0 -1.5 -2.0 RL = 10k V+ = 5V CL = 16.3pF AV = 10k Rg = 10 Rf = 100k -2.5 0.01 1 10 100 1k 10k -3.0 100k 0 1 2 3 4 FREQUENCY (Hz) 5 6 TIME (s) 7 8 9 10 FIGURE 14. INPUT VOLTAGE NOISE 0.1Hz TO 10Hz FIGURE 13. INPUT CURRENT NOISE DENSITY vs FREQUENCY 0.025 2.0 SMALL SIGNAL (V) 1.0 0.5 0 V+, V- = 2.5V RL = 1k CL = 16.3pF Rg = Rf = 10k AV = 2 VOUT = 3VP-P -1.0 -1.5 -2.0 0 1 2 3 4 5 6 TIME (s) 7 8 9 0.020 0.010 10 V+, V- = 2.5V RL = 1k CL = 16.3pF Rg= Rf = 10k AV = 2 VOUT = 10mVP-P 0.015 0 1 2 3 4 5 6 7 8 9 10 TIME (s) FIGURE 15. LARGE SIGNAL STEP RESPONSE FIGURE 16. SMALL SIGNAL STEP RESPONSE 1.2 3.5 VOUT VEN 3.0 1.0 2.5 0.8 V+ = 5V Rg = Rf = 10k CL = 16.3pF AV = +2 VOUT = 1VP-P 2.0 1.5 1.0 0.5 0.6 0.4 0.2 RL = 10k 0 0 -0.5 OUTPUT (V) -0.5 VENABLE (V) LARGE SIGNAL (V) 1.5 0 10 20 30 40 50 60 TIME (s) 70 80 90 -0.2 100 FIGURE 17. ISL28148 ENABLE TO OUTPUT RESPONSE 7 FN6337.4 September 21, 2010 ISL28148, ISL28248, ISL28448 Typical Performance Curves V+ = 5V, V- = 0V, VCM = 2.5V, RL = Open 100 800 V+ = 5V RL = OPEN Rf = 100k, Rg = 100 AV = +1k 600 60 40 200 0 -200 20 0 -20 -40 -400 -60 -600 -80 0 1 2 3 VCM (V) 4 5 -1 1.2 10.5 1.1 9.5 MEDIAN 0.9 0.8 MIN 0.7 2 3 VCM (V) 4 5 6 MAX 8.5 MEDIAN 7.5 6.5 MIN 5.5 4.5 -20 0 20 40 60 80 TEMPERATURE (C) 100 3.5 -40 120 FIGURE 20. SUPPLY CURRENT ENABLED vs TEMPERATURE V+, V- = 2.5V -20 0 20 40 60 80 TEMPERATURE (C) 100 120 FIGURE 21. SUPPLY CURRENT DISABLED vs TEMPERATURE V+, V- = 2.5V 2.0 2.0 MAX 1.5 MAX 1.5 1.0 1.0 VOS (mV) 0.5 MEDIAN 0 -0.5 0.5 MEDIAN 0 -0.5 -1.0 -1.0 MIN -1.5 -2.0 -40 1 MAX 1.0 0.6 -40 0 FIGURE 19. INPUT BIAS CURRENT vs COMMON MODE INPUT VOLTAGE CURRENT (A) CURRENT (mA) -100 6 FIGURE 18. INPUT OFFSET VOLTAGE vs COMMON MODE INPUT VOLTAGE VOS (mV) V+ = 5V RL = OPEN Rf = 100k, Rg = 100 AV = +1k 80 IBIAS (pA) VOS (V) 400 -800 -1 (Continued) -20 0 20 40 60 80 TEMPERATURE (C) 100 120 FIGURE 22. VOS vs TEMPERATURE VIN = 0V, V+, V- = 2.75V 8 MIN -1.5 -2.0 -40 -20 0 20 40 60 80 TEMPERATURE (C) 100 120 FIGURE 23. VOS vs TEMPERATURE VIN = 0V, V+, V- = 2.5V FN6337.4 September 21, 2010 ISL28148, ISL28248, ISL28448 Typical Performance Curves V+ = 5V, V- = 0V, VCM = 2.5V, RL = Open 2.0 300 MAX 1.5 250 1.0 200 IBIAS- (pA) VOS (mV) 0.5 MEDIAN 0 -0.5 MIN -20 0 MIN 0 20 40 60 80 TEMPERATURE (C) 100 -50 -40 120 -20 0 20 40 60 80 TEMPERATURE (C) 100 120 FIGURE 25. IBIAS- vs TEMPERATURE V+, V- = 2.5V FIGURE 24. VOS vs TEMPERATURE VIN = 0V, V+, V- = 1.2V 250 10 0 200 MAX 150 MEDIAN 100 50 MAX -10 IOS (pA) IBIAS- (pA) MEDIAN 100 50 -1.5 MIN -20 MEDIAN -30 MIN -40 -50 0 -50 -40 MAX 150 -1.0 -2.0 -40 (Continued) -60 -20 0 20 40 60 80 TEMPERATURE (C) 100 -70 -40 120 -20 0 20 40 60 80 TEMPERATURE (C) 100 120 FIGURE 27. IOS vs TEMPERATURE V+, V- = 2.5V FIGURE 26. IBIAS- vs TEMPERATURE V+, V- = 1.2V 20 1750 10 1550 MAX -10 -20 AVOL (V/mV) IOS (pA) 0 MEDIAN -30 MIN 1350 1150 950 -40 550 -50 350 -60 -40 -20 0 20 40 60 80 TEMPERATURE (C) 100 120 FIGURE 28. IOS vs TEMPERATURE V+, V- = 1.2V 9 MAX 750 150 -40 MEDIAN MIN -20 0 20 40 60 80 TEMPERATURE (C) 100 120 FIGURE 29. AVOL vs TEMPERATURE RL = 100k, V+, V- = 2.5V, VO = -2V TO +2V FN6337.4 September 21, 2010 ISL28148, ISL28248, ISL28448 80 140 70 130 MAX 50 MEDIAN 40 MAX 110 MEDIAN 100 90 30 20 -40 (Continued) 120 60 CMRR (dB) AVOL (V/mV) Typical Performance Curves V+ = 5V, V- = 0V, VCM = 2.5V, RL = Open MIN -20 0 20 40 60 80 TEMPERATURE (C) MIN 80 100 70 -40 120 FIGURE 30. AVOL vs TEMPERATURE RL = 1k, V+, V- = 2.5V, VO = -2V TO +2V -20 0 20 40 60 80 TEMPERATURE (C) 4.970 130 4.965 MAX MAX 120 4.960 VOUT (V) PSRR (dB) 120 FIGURE 31. CMRR vs TEMPERATURE VCM = -2.5V TO +2.5V, V+, V- = 2.5V 140 110 100 MEDIAN MIN 80 70 -40 -20 0 20 40 60 80 TEMPERATURE (C) MEDIAN MIN 4.945 100 4.940 -40 120 FIGURE 32. PSRR vs TEMPERATURE V+, V- = 1.2V TO 2.75V -20 0 100 120 75 70 4.9992 MAX MAX 65 VOUT (mV) 4.9990 4.9988 MEDIAN 60 MEDIAN 55 50 MIN MIN 4.9984 4.9982 -40 20 40 60 80 TEMPERATURE (C) FIGURE 33. VOUT HIGH vs TEMPERATURE RL = 1k, V+, V- = 2.5V 4.9994 4.9986 4.955 4.950 90 VOUT (V) 100 45 -20 0 20 40 60 80 TEMPERATURE (C) 100 FIGURE 34. VOUT HIGH vs TEMPERATURE RL = 100k, V+, V- = 2.5V 10 120 40 -40 -20 0 20 40 60 80 TEMPERATURE (C) 100 120 FIGURE 35. VOUT LOW vs TEMPERATURE RL = 1k, V+, V- = 2.5V FN6337.4 September 21, 2010 ISL28148, ISL28248, ISL28448 Typical Performance Curves V+ = 5V, V- = 0V, VCM = 2.5V, RL = Open 95 3.3 + OUTPUT SHORT CIRCUIT CURRENT (mA) 3.1 VOUT (mV) 2.9 MAX 2.7 2.5 2.3 MEDIAN 2.1 MIN 1.9 1.7 1.5 -40 (Continued) -20 0 20 40 60 80 TEMPERATURE (C) 100 90 MAX 85 80 MEDIAN 75 70 MIN 65 60 -40 120 -20 0 20 40 60 80 TEMPERATURE (C) 100 120 FIGURE 37. + OUTPUT SHORT CIRCUIT CURRENT vs TEMPERATURE VIN = 2.55V, RL = 10, V+, V- = 2.5V FIGURE 36. VOUT LOW vs TEMPERATURE RL = 100k, V+, V- = 2.5V - OUTPUT SHORT CIRCUIT CURRENT (mA) -50 -55 MAX -60 MEDIAN -65 -70 MIN -75 -80 -85 -40 -20 0 20 40 60 80 TEMPERATURE (C) 100 120 FIGURE 38. - OUTPUT SHORT CIRCUIT CURRENT vs TEMPERATURE VIN = -2.55V, RL = 10, V+, V- = 2.5V Pin Descriptions ISL28148 (6 Ld SOT-23) ISL28248 (8 Ld SO) (8 Ld MSOP) ISL28448 (14 Ld TSSOP) PIN NAME 2 (A) 6 (B) 9 (C) 13 (D) ININ-_A IN-_B IN-_C IN-_D 4 2 (A) 6 (B) FUNCTION EQUIVALENT CIRCUIT inverting input V+ IN- IN+ VCircuit 1 3 3 (A) 5 (B) 11 3 (A) 5 (B) 10 (C) 12 (D) IN+ IN+_A IN+_B IN+_C IN+_D Non-inverting input (See circuit 1) FN6337.4 September 21, 2010 ISL28148, ISL28248, ISL28448 Pin Descriptions (Continued) ISL28148 (6 Ld SOT-23) ISL28248 (8 Ld SO) (8 Ld MSOP) ISL28448 (14 Ld TSSOP) PIN NAME 2 4 11 V- FUNCTION Negative supply EQUIVALENT CIRCUIT V+ CAPACITIVELY COUPLED ESD CLAMP VCircuit 2 1 1 (A) 7 (B) 1 (A) 7 (B) 8 (C) 14 (D) OUT OUT_A OUT_B OUT_C OUT_D Output V+ OUT VCircuit 3 6 8 5 4 V+ Positive supply - EN Chip enable (See circuit 2) V+ EN VCircuit 4 Applications Information Introduction The ISL28148, ISL28248 and ISL28448 are single, dual and quad channel CMOS rail-to-rail input, output (RRIO) micropower precision operational amplifiers. The parts are designed to operate from single supply (2.4V to 5.5V) or dual supply (1.2V to 2.75V). The parts have an input common mode range that extends 0.25V above the positive rail and 100mV below the negative supply rail. The output can swing within about 3mV of the supply rails with a 100k load. Rail-to-Rail Input Many rail-to-rail input stages use two differential input pairs, a long-tail PNP (or PFET) and an NPN (or NFET). Severe penalties have to be paid for this circuit topology. As the input signal moves from one supply rail to another, the operational amplifier switches from one input pair to the other causing drastic changes in input offset voltage and an undesired change in magnitude and polarity of input offset current. The parts achieve input rail-to-rail operation without sacrificing important precision specifications and degrading distortion performance. The devices' input offset voltage exhibits a smooth behavior throughout the entire common-mode input range. The input bias current vs the common-mode voltage range gives us an undistorted 12 behavior from typically 100mV below the negative rail and 0.25V higher than the V+ rail. Rail-to-Rail Output A pair of complementary MOS devices are used to achieve the rail-to-rail output swing. The NMOS sinks current to swing the output in the negative direction. The PMOS sources current to swing the output in the positive direction. The devices' with a 100k load will swing to within 3mV of the positive supply rail and within 3mV of the negative supply rail. Results of Overdriving the Output Caution should be used when overdriving the output for long periods of time. Overdriving the output can occur in two ways: 1. The input voltage times the gain of the amplifier exceeds the supply voltage by a large value or 2. The output current required is higher than the output stage can deliver. These conditions can result in a shift in the Input Offset Voltage (VOS) as much as 1V/hr. of exposure under these condition. IN+ and IN- Input Protection All input terminals have internal ESD protection diodes to both positive and negative supply rails, limiting the input voltage to within one diode beyond the supply rails. They also contain back-to-back diodes across the input terminals ("Pin Descriptions" table - Circuit 1 on page 11). For applications where the input differential voltage is expected to exceed FN6337.4 September 21, 2010 ISL28148, ISL28248, ISL28448 0.5V, an external series resistor must be used to ensure the input currents never exceed 5mA (Figure 39). VIN VOUT RIN RL + FIGURE 39. INPUT CURRENT LIMITING Enable/Disable Feature The ISL28148 offers an EN pin that disables the device when pulled up to at least 2.0V. In the disabled state (output in a high impedance state), the part consumes typically 10A at room temperature. By disabling the part, multiple ISL28148 parts can be connected together as a MUX. In this configuration, the outputs are tied together in parallel and a channel can be selected by the EN pin. The loading effects of the feedback resistors of the disabled amplifier must be considered when multiple amplifier outputs are connected together. Note that feed-through from the IN+ to IN- pins occurs on any Mux Amp disabled channel where the input differential voltage exceeds 0.5V (e.g., active channel VOUT = 1V, while disabled channel VIN = GND), so the mux implementation is best suited for small signal applications. If large signals are required, use series IN+ resistors, or large value RF, to keep the feed-through current low enough to minimize the impact on the active channel. See "Limitations of the Differential Input Protection" on page 13 for more details.The EN pin also has an internal pull-down. If left open, the EN pin will pull to the negative rail and the device will be enabled by default. When not used, the EN pin should either be left floating or connected directly to the V- pin. Limitations of the Differential Input Protection If the input differential voltage is expected to exceed 0.5V, an external current limiting resistor must be used to ensure the input current never exceeds 5mA. For non-inverting unity gain applications the current limiting can be via a series IN+ resistor, or via a feedback resistor of appropriate value. For other gain configurations, the series IN+ resistor is the best choice, unless the feedback (RF) and gain setting (RG) resistors are both sufficiently large to limit the input current to 5mA. Large differential input voltages can arise from several sources: visible distortion occurs on the input and output signals. To avoid this issue, keep the input slew rate below 4.8V/s, or use appropriate current limiting resistors. Large (>2V) differential input voltages can also cause an increase in disabled ICC. Using Only One Channel If the application does not use all channels, then the user must configure the unused channel(s) to prevent them from oscillating. The unused channel(s) will oscillate if the input and output pins are floating. This will result in higher than expected supply currents and possible noise injection into the channel being used. The proper way to prevent this oscillation is to short the output to the negative input and ground the positive input (as shown in Figure 40). + FIGURE 40. PREVENTING OSCILLATIONS IN UNUSED CHANNELS Proper Layout Maximizes Performance To achieve the maximum performance of the high input impedance and low offset voltage, care should be taken in the circuit board layout. The PC board surface must remain clean and free of moisture to avoid leakage currents between adjacent traces. Surface coating of the circuit board will reduce surface moisture and provide a humidity barrier, reducing parasitic resistance on the board. When input leakage current is a concern, the use of guard rings around the amplifier inputs will further reduce leakage currents. Figure 41 shows a guard ring example for a unity gain amplifier that uses the low impedance amplifier output at the same voltage as the high impedance input to eliminate surface leakage. The guard ring does not need to be a specific width, but it should form a continuous loop around both inputs. For further reduction of leakage currents, components can be mounted to the PC board using Teflon standoff insulators. . HIGH IMPEDANCE INPUT V+ IN * During open loop (comparator) operation. Used this way, the IN+ and IN- voltages don't track, so differentials arise. * When the amplifier is disabled but an input signal is still present. An RL or RG to GND keeps the IN- at GND, while the varying IN+ signal creates a differential voltage. Mux Amp applications are similar, except that the active channel VOUT determines the voltage on the IN- terminal. * When the slew rate of the input pulse is considerably faster than the op amp's slew rate. If the VOUT can't keep up with the IN+ signal, a differential voltage results, and 13 FIGURE 41. GUARD RING EXAMPLE FOR UNITY GAIN AMPLIFIER Current Limiting These devices have no internal current-limiting circuitry. If the output is shorted, it is possible to exceed the Absolute Maximum Rating for output current or power dissipation, potentially resulting in the destruction of the device. FN6337.4 September 21, 2010 ISL28148, ISL28248, ISL28448 Power Dissipation where: It is possible to exceed the +150C maximum junction temperatures under certain load and power-supply conditions. It is therefore important to calculate the maximum junction temperature (TJMAX) for all applications to determine if power supply voltages, load conditions, or package type need to be modified to remain in the safe operating area. These parameters are related in Equation 1: * TMAX = Maximum ambient temperature T JMAX = T MAX + ( JA xPD MAXTOTAL ) (EQ. 1) where: * JA = Thermal resistance of the package * PDMAX = Maximum power dissipation of 1 amplifier * VS = Supply voltage (Magnitude of V+ and V-) * IMAX = Maximum supply current of 1 amplifier * VOUTMAX = Maximum output voltage swing of the application * RL = Load resistance * PDMAXTOTAL is the sum of the maximum power dissipation of each amplifier in the package (PDMAX) * PDMAX for each amplifier can be calculated as shown in Equation 2: V OUTMAX PD MAX = 2*V S x I SMAX + ( V S - V OUTMAX ) x ---------------------------RL (EQ. 2) 14 FN6337.4 September 21, 2010 ISL28148, ISL28248, ISL28448 Package Outline Drawing P6.064A 6 LEAD SMALL OUTLINE TRANSISTOR PLASTIC PACKAGE Rev 0, 2/10 1.90 0-3 0.95 D 0.08-0.20 A 5 6 4 PIN 1 INDEX AREA 2.80 3 1.60 3 0.15 C D 2x 5 (0.60) 1 3 2 0.20 C 2x 0.40 0.05 B SEE DETAIL X 3 0.20 M C A-B D TOP VIEW 2.90 5 END VIEW 10 TYP (2 PLCS) 0.15 C A-B 2x H 1.14 0.15 1.45 MAX C SIDE VIEW 0.10 C 0.05-0.15 SEATING PLANE DETAIL "X" (0.25) GAUGE PLANE 0.450.1 4 (0.60) (1.20) NOTES: (2.40) (0.95) 1. Dimensions are in millimeters. Dimensions in ( ) for Reference Only. 2. Dimensioning and tolerancing conform to ASME Y14.5M-1994. 3. Dimension is exclusive of mold flash, protrusions or gate burrs. 4. Foot length is measured at reference to guage plane. 5. This dimension is measured at Datum "H". 6. Package conforms to JEDEC MO-178AA. (1.90) TYPICAL RECOMMENDED LAND PATTERN 15 FN6337.4 September 21, 2010 ISL28148, ISL28248, ISL28448 Package Outline Drawing M8.15E 8 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE Rev 0, 08/09 4 4.90 0.10 A DETAIL "A" 0.22 0.03 B 6.0 0.20 3.90 0.10 4 PIN NO.1 ID MARK 5 (0.35) x 45 4 4 0.43 0.076 1.27 0.25 M C A B SIDE VIEW "B" TOP VIEW 1.75 MAX 1.45 0.1 0.25 GAUGE PLANE C SEATING PLANE 0.10 C 0.175 0.075 SIDE VIEW "A 0.63 0.23 DETAIL "A" (0.60) (1.27) NOTES: (1.50) (5.40) 1. Dimensions are in millimeters. Dimensions in ( ) for Reference Only. 2. Dimensioning and tolerancing conform to AMSE Y14.5m-1994. 3. Unless otherwise specified, tolerance : Decimal 0.05 4. Dimension does not include interlead flash or protrusions. Interlead flash or protrusions shall not exceed 0.25mm per side. 5. The pin #1 identifier may be either a mold or mark feature. 6. Reference to JEDEC MS-012. TYPICAL RECOMMENDED LAND PATTERN 16 FN6337.4 September 21, 2010 ISL28148, ISL28248, ISL28448 Package Outline Drawing M8.118A 8 LEAD MINI SMALL OUTLINE PLASTIC PACKAGE (MSOP) Rev 0, 9/09 A 3.00.1 8 0.25 CAB 3.00.1 4.90.15 DETAIL "X" 1.10 Max PIN# 1 ID B SIDE VIEW 2 1 0.18 0.05 2 0.65 BSC TOP VIEW 0.95 BSC 0.860.09 GAUGE PLANE H C 0.25 SEATING PLANE 0.33 +0.07/ -0.08 0.08 C A B 0.10 0.05 33 0.10 C 0.55 0.15 DETAIL "X" SIDE VIEW 1 5.80 NOTES: 4.40 3.00 1. Dimensions are in millimeters. 2. Dimensioning and tolerancing conform to JEDEC MO-187-AA and AMSE Y14.5m-1994. 3. Plastic or metal protrusions of 0.15mm max per side are not included. 4. Plastic interlead protrusions of 0.25mm max per side are not included. 5. Dimensions "D" and "E1" are measured at Datum Plane "H". 6. This replaces existing drawing # MDP0043 MSOP 8L. 0.65 0.40 1.40 TYPICAL RECOMMENDED LAND PATTERN 17 FN6337.4 September 21, 2010 ISL28148, ISL28248, ISL28448 Thin Shrink Small Outline Plastic Packages (TSSOP) M14.173 N INDEX AREA E 0.25(0.010) M E1 2 SYMBOL 3 0.05(0.002) -A- INCHES GAUGE PLANE -B1 14 LEAD THIN SHRINK SMALL OUTLINE PLASTIC PACKAGE B M 0.25 0.010 SEATING PLANE L A D -C- e A1 b A2 c 0.10(0.004) 0.10(0.004) M C A M B S MIN 1. These package dimensions are within allowable dimensions of JEDEC MO-153-AC, Issue E. MILLIMETERS MIN MAX NOTES A - 0.047 - 1.20 - A1 0.002 0.006 0.05 0.15 - A2 0.031 0.041 0.80 1.05 - b 0.0075 0.0118 0.19 0.30 9 c 0.0035 0.0079 0.09 0.20 - D 0.195 0.199 4.95 5.05 3 E1 0.169 0.177 4.30 4.50 4 e 0.026 BSC 0.65 BSC - E 0.246 0.256 6.25 6.50 - L 0.0177 0.0295 0.45 0.75 6 8o 0o N NOTES: MAX 14 0o 14 7 8o Rev. 2 4/06 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimension "D" does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension "E1" does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.15mm (0.006 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. "L" is the length of terminal for soldering to a substrate. 7. "N" is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. Dimension "b" does not include dambar protrusion. Allowable dambar protrusion shall be 0.08mm (0.003 inch) total in excess of "b" dimension at maximum material condition. Minimum space between protrusion and adjacent lead is 0.07mm (0.0027 inch). 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. (Angles in degrees) All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation's quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 18 FN6337.4 September 21, 2010