VBATT: 2.7 V to 5.5 V
IN
OUT
GND
EN
-+
For example,
1.5 V
1 PF
BATT
LP5952
Pre-
regulator
Li-Ion
or
3-cell
NiMh/NiCd
2.2 PF
For example, 1.2 V
A1
B2C3
A3
C1
Load
0 to 350 mA
Product
Folder
Sample &
Buy
Technical
Documents
Tools &
Software
Support &
Community
LP5952
SNVS469F –OCTOBER 2006–REVISED DECEMBER 2015
LP5952 350-mA Dual-Rail Linear Regulator
1 Features 3 Description
The LP5952 is a dual-supply-rail linear regulator
1• Input Voltage Range: 0.7 V to 4.5 V optimized for powering ultralow-voltage circuits from a
• 2.5 V ≤VBATT ≤5.5 V single Li-Ion cell or 3-cell NiMH/NiCd battery.
• 0.5V ≤VOUT ≤2 V In the typical post-regulation application VBATT is
• Ensured 350-mA Output Current directly connected to the battery (range 2.5 V to
• For ILOAD = 350 mA: 5.5 V), and VIN is supplied by the output voltage of
the DC-DC converter (range 0.7 V to 4.5 V).
– VBATT ≥VOUT(NOM) + 1.5 V or 2.5 V
(Whichever is Higher) The device offers superior dropout and transient
• For ILOAD = 150 mA: features combined with very low quiescent currents.
In shutdown mode (Enable (EN) pin pulled low) the
– VBATT ≥VOUT(NOM) + 1.3 V or 2.5 V device turns off and reduces battery consumption to
(Whichever is Higher) 0.1 µA (typical). The LP5952 also features internal
• Excellent Load Transient Response: ±15 mV protection against overtemperature, overcurrent, and
Typical undervoltage conditions.
• Excellent Line Transient Response: ±1 mV Typical Depending upon application, only one or two tiny
• 50-µA Typical Quiescent Current from VBATT surface-mount external components are required;
performance is specified for a –40°C to +125°C
• 10-µA Typical Quiescent Current from VIN junction temperature range. The device is available in
• 0.1-µA Typical Quiescent Current in Shutdown fixed output voltages from 0.5 V to 2 V. For
• Noise voltage = 100 µVRMS Typical availability, please contact your local Texas
• Operates from a Single Li-Ion Cell or 3-Cell Instruments sales office.
NiMH/NiCd Battery Device Information(1)
• Thermal-Overload and Short-Circuit Protection PART NUMBER PACKAGE BODY SIZE (NOM)
DSBGA (5) 1.326 mm × 0.96 mm
2 Applications LP5952 USON (6) 2.00 mm × 2.00 mm
• Mobile Phones (1) For all available packages, see the orderable addendum at
• Hand-Held Radios the end of the data sheet.
• Personal Digital Assistants
• Palm-Top PCs
• Portable Instruments
• Battery-Powered Devices
Typical Application Circuit
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LP5952
SNVS469F –OCTOBER 2006–REVISED DECEMBER 2015
www.ti.com
Table of Contents
7.1 Overview................................................................. 10
1 Features.................................................................. 17.2 Functional Block Diagram....................................... 10
2 Applications ........................................................... 17.3 Feature Description................................................. 10
3 Description............................................................. 17.4 Device Functional Modes........................................ 11
4 Revision History..................................................... 28 Application and Implementation ........................ 12
5 Pin Configuration and Functions......................... 38.1 Application Information............................................ 12
6 Specifications......................................................... 48.2 Typical Application ................................................. 12
6.1 Absolute Maximum Ratings ...................................... 49 Power Supply Recommendations...................... 17
6.2 ESD Ratings.............................................................. 410 Layout................................................................... 18
6.3 Recommended Operating Conditions....................... 410.1 Layout Guidelines ................................................. 18
6.4 Thermal Information ................................................. 510.2 Layout Examples................................................... 18
6.5 Electrical Characteristics........................................... 511 Device and Documentation Support................. 19
6.6 Electrical Characteristics: Quiescent Currents.......... 611.1 Device Support .................................................... 19
6.7 Electrical Characteristics: Shutdown Currents.......... 611.2 Documentation Support ....................................... 19
6.8 Electrical Characteristics: Enable Control................. 611.3 Community Resources.......................................... 19
6.9 Electrical Characteristics: Thermal Protection.......... 711.4 Trademarks........................................................... 19
6.10 Electrical Characteristics: Transient
Characteristics ........................................................... 711.5 Electrostatic Discharge Caution............................ 19
6.11 Input and Output Capacitors (Recommended)....... 711.6 Glossary................................................................ 19
6.12 Typical Characteristics............................................ 812 Mechanical, Packaging, and Orderable
Information........................................................... 19
7 Detailed Description............................................ 10
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision E (May 2013) to Revision F Page
• Added Device Information and Pin Configuration and Functions sections, ESD Ratings and Thermal Information
tables, Feature Description,Device Functional Modes,Application and Implementation,Power Supply
Recommendations,Layout,Device and Documentation Support, and Mechanical, Packaging, and Orderable
Information sections; update pin names to TI nomenclature.................................................................................................. 1
• Deleted lead temp spec - it is in POA ................................................................................................................................... 4
• Updated thermal information ................................................................................................................................................. 5
• Changed values for thermal specifications in Power Dissipation section per updated thermal information ....................... 14
Changes from Revision D (April 2013) to Revision E Page
• Changed layout of National Data Sheet to TI format ........................................................................................................... 18
2Submit Documentation Feedback Copyright © 2006–2015, Texas Instruments Incorporated
Product Folder Links: LP5952
EN
6
5
NC
4
OUT
1
BATT
2
GND
3
IN
A3 C3
A1 B2 C1
OUT EN
IN GND BATT
LP5952
www.ti.com
SNVS469F –OCTOBER 2006–REVISED DECEMBER 2015
5 Pin Configuration and Functions
YZR Package
5-Pin DSBGA
Top View
NC - No internal connection NKH Package
6-Pin USON
Top View
Pin Functions
PIN TYPE DESCRIPTION
NAME USON DSGBA
BATT 1 C1 Input Bias input voltage; input range: 2.5 V to 5.5 V
Enable pin logic input: low = shutdown, high = active, normal operation. This
EN 6 C3 Input pin should not be left floating. Tie to BATT if this function is not used.
GND 2 B2 Ground Ground
IN 3 A1 Input Power input voltage; input range: 0.7 V to 4.5 V, VIN ≤VBATT
NC 5 — — Do not make connections to this pin.
OUT 4 A3 Output Regulated output voltage
Copyright © 2006–2015, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Links: LP5952
LP5952
SNVS469F –OCTOBER 2006–REVISED DECEMBER 2015
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)(1)(2)(3)
MIN MAX UNIT
IN, BATT pins: Voltage to GND, VIN ≤VBATT –0.2 V
BATT pin to IN pin 0.2 V
EN pin, voltage to GND –0.2 V
Continuous power dissipation(4) Internally limited
Junction Temperature (TJ-MAX ) 150 °C
Storage temperature, Tstg –65 150 °C
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) All voltages are with respect to the potential at the GND pin.
(3) If Military or Aerospace specified devices are required, contact Texas Instruments Sales Office or Distributors for availability and
specifications.
(4) Internal thermal shutdown circuitry protects the device from permanent damage. Thermal shutdown engages at TJ= 165°C (typical) and
disengages at TJ= 145°C (typical).
6.2 ESD Ratings VALUE UNIT
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1) ±2000
V(ESD) Electrostatic discharge V
Machine model ±200
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted) MIN MAX UNIT
Input voltage, VIN 0.7 4.5 V
Input voltage, VBATT 2.5 5.5 V
Input voltage, VEN 0 VBATT V
Recommended load current 0 350 mA
Junction temperature, TJ–40 125 °C
Ambient temperature, TA(1) –40 85 °C
(1) In applications where high power dissipation and/or poor package thermal resistance is present, the maximum ambient temperature may
have to be derated. Maximum ambient temperature (TA-MAX) is dependent on the maximum operating junction temperature (TJ-MAX-OP =
125°C), the maximum power dissipation of the device in the application (PD-MAX), and the junction-to ambient thermal resistance of the
part/package in the application (RθJA), as given by: TA-MAX = TJ-MAX-OP – (RθJA × PD-MAX).
4Submit Documentation Feedback Copyright © 2006–2015, Texas Instruments Incorporated
Product Folder Links: LP5952
LP5952
www.ti.com
SNVS469F –OCTOBER 2006–REVISED DECEMBER 2015
6.4 Thermal Information LP5952
THERMAL METRIC(1) YZR (DSBGA) NKH (USON) UNIT
5 PINS 6 PINS
RθJA Junction-to-ambient thermal resistance(2) 181.0 181.6 °C/W
RθJC(top) Junction-to-case (top) thermal resistance 0.9 93.1 °C/W
RθJB Junction-to-board thermal resistance 110.3 116.7 °C/W
ψJT Junction-to-top characterization parameter 7.4 8.0 °C/W
ψJB Junction-to-board characterization parameter 110.3 116.7 °C/W
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.
(2) Junction-to-ambient thermal resistance is highly application and board-layout dependent. In applications where high maximum power
dissipation exists, special attention must be paid to thermal dissipation issues in board design.
6.5 Electrical Characteristics
Unless otherwise noted, typical values are for TA= 25°C, and minimum and maximum limits apply over the full operating
temperature range: –40°C ≤TJ≤+125°C; specifications apply to the Typical Application Circuit with VIN = VOUT(NOM) + 1 V,
VBATT = VOUT(NOM) + 1.5 V or 2.5 V (whichever is higher), IOUT = 1 mA, CVIN = 1 µF, COUT = 2.2 µF, VEN = VBATT.(1)(2)(3)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
VIN = VOUT(NOM) + 0.3 V, TA= 25°C –1.5 1.5
ΔVOUT / VOUT Output voltage tolerance VIN = VOUT(NOM) + 0.3 V 2 2
VIN = VOUT(NOM) + 0.3 V to 4.5 V, VBATT = 1 0.3 1 mV/V
ΔVOUT /ΔVIN 4.5 V
Line regulation error
ΔVOUT / VBATT = VOUT(NOM) + 1.5 V (≥2.5 V) to 5.5 2.2 2.2
0.5
ΔVBATT VDSBGA 30
IOUT = 1 mA to 350 mA 15 30 µV/mA
package
ΔVOUT /ΔmA Load regulation error USON 60
IOUT = 1 mA to 350 mA 43 60 µV/mA
package
Output current (short VOUT = 0 V, VEN = VIN = VBATT = VOUT(NOM)
ISC 350 500 mA
circuit) + 1.5 V
IOUT = 350 mA, VIN = DSBGA 1.07 1.5 V
VOUT(NOM) + 0.3 V package
IOUT = 350 mA USON 1.08 1.5 V
VIN = VOUT(NOM) + 0.3 V package
VDO_VBATT Output voltage dropout
(4) VBATT(5) IOUT = 150 mA DSBGA 0.96 1.3 V
VIN = VOUT(NOM) + 0.3 V package
IOUT = 150 mA USON 0.97 1.3 V
VIN = VOUT(NOM) + 0.3 V package
IOUT = 350 mA DSBGA
VBATT = VOUT(NOM) + 1.5 V 88 200 mV
package
or 2.5 V
Output voltage dropout
VDO_VIN VIN IOUT = 350 mA USON
VBATT = VOUT(NOM) + 1.5 V 128 250 mV
package
or 2.5 V
ENOutput noise 10 Hz to 100 kHz 100 µVRMS
(1) All voltages are with respect to the potential at the GND pin.
(2) Minimum and maximum limits are ensured by design, test, or statistical analysis. Typical numbers are not ensured, but do represent the
most likely norm. Unless otherwise specified, conditions for typical specifications are: VIN = VOUT(NOM) + 1 V, VBATT = VOUT(NOM) + 1.5 V
or 2.5 V, whichever is higher, TA= 25°C.
(3) VOUT(NOM) is the stated output voltage option
(4) This specification does not apply if the battery voltage VBATT needs to be decreased below the minimum operating limit of 2.5 V during
this test.
(5) Dropout voltage is defined as the input to output voltage differential at which the output voltage falls to 100mV below the nominal output
voltage.
Copyright © 2006–2015, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Links: LP5952
LP5952
SNVS469F –OCTOBER 2006–REVISED DECEMBER 2015
www.ti.com
Electrical Characteristics (continued)
Unless otherwise noted, typical values are for TA= 25°C, and minimum and maximum limits apply over the full operating
temperature range: –40°C ≤TJ≤+125°C; specifications apply to the Typical Application Circuit with VIN = VOUT(NOM) + 1 V,
VBATT = VOUT(NOM) + 1.5 V or 2.5 V (whichever is higher), IOUT = 1 mA, CVIN = 1 µF, COUT = 2.2 µF, VEN = VBATT.(1)(2)(3)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
Sine modulated VBATT, ƒ = 10 Hz 70
Power Supply Rejection
PSRR Sine modulated VBATT, ƒ = 100 Hz 65 dB
Ratio Sine modulated VBATT, ƒ = 1 kHz 45
Sine modulated VIN, ƒ = 10 Hz 80
Sine modulated VIN, ƒ = 100 Hz 90
Power Supply Rejection
PSRR Sine modulated VIN, ƒ = 1 kHz 95 dB
Ratio Sine modulated VIN, ƒ = 10 kHz 85
Sine modulated VIN, ƒ = 100 kHz 64
6.6 Electrical Characteristics: Quiescent Currents
Unless otherwise noted, typical values are for TA= 25°C, and minimum and maximum limits apply over the full operating
temperature range: –40°C ≤TJ≤+125°C.(1)(2)(3)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
IQ_VBATT Current into VBATT ILOAD = 0 mA to 350mA 50 100 µA
IQ_VIN Current into VIN ILOAD = 0 11 28 µA
(1) All voltages are with respect to the potential at the GND pin.
(2) Minimum and maximum limits are ensured by design, test, or statistical analysis. Typical numbers are not ensured, but do represent the
most likely norm. Unless otherwise specified, conditions for typical specifications are: VIN = VOUT(NOM) + 1 V, VBATT = VOUT(NOM) + 1.5 V
or 2.5 V, whichever is higher, TA= 25°C.
(3) VOUT(NOM) is the stated output voltage option
6.7 Electrical Characteristics: Shutdown Currents
Unless otherwise noted, typical values are for TA= 25°C, and minimum and maximum limits apply over the full operating
temperature range: –40°C ≤TJ≤+125°C.(1)(2)(3)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
IQ_VBATT Current into VBATT VEN = 0 V 0.1 1 µA
IQ_VIN Current into VIN VEN = 0 V 0.1 1 µA
(1) All voltages are with respect to the potential at the GND pin.
(2) Minimum and maximum limits are ensured by design, test, or statistical analysis. Typical numbers are not ensured, but do represent the
most likely norm. Unless otherwise specified, conditions for typical specifications are: VIN = VOUT(NOM) + 1 V, VBATT = VOUT(NOM) + 1.5 V
or 2.5 V, whichever is higher, TA= 25°C.
(3) VOUT(NOM) is the stated output voltage option.
6.8 Electrical Characteristics: Enable Control
Unless otherwise noted, typical values are for TA= 25°C, and minimum and maximum limits apply over the full operating
temperature range: –40°C ≤TJ≤+125°C.(1)(2)(3)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
IEN Maximum input current at EN input 0.01 1 µA
VIL Low input threshold (shutdown) 0.4 V
VIH High input threshold (enable) 1 V
(1) All voltages are with respect to the potential at the GND pin.
(2) Minimum and maximum limits are ensured by design, test, or statistical analysis. Typical numbers are not ensured, but do represent the
most likely norm. Unless otherwise specified, conditions for typical specifications are: VIN = VOUT(NOM) + 1 V, VBATT = VOUT(NOM) + 1.5 V
or 2.5 V, whichever is higher, TA= 25°C.
(3) VOUT(NOM) is the stated output voltage option.
6Submit Documentation Feedback Copyright © 2006–2015, Texas Instruments Incorporated
Product Folder Links: LP5952
LP5952
www.ti.com
SNVS469F –OCTOBER 2006–REVISED DECEMBER 2015
6.9 Electrical Characteristics: Thermal Protection
Typical values are for TA= 25°C.(1)(2)(3)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
TSHDN Thermal-shutdown temperature 165 °C
ΔTSHDN Thermal-shutdown hysteresis 20 °C
(1) All voltages are with respect to the potential at the GND pin.
(2) Minimum and maximum limits are ensured by design, test, or statistical analysis. Typical numbers are not ensured, but do represent the
most likely norm. Unless otherwise specified, conditions for typical specifications are: VIN = VOUT(NOM) + 1 V, VBATT = VOUT(NOM) + 1.5 V
or 2.5 V, whichever is higher, TA= 25°C.
(3) VOUT(NOM) is the stated output voltage option.
6.10 Electrical Characteristics: Transient Characteristics
Unless otherwise noted, typical values are for TA= 25°C, and minimum and maximum limits apply over the full operating
temperature range: –40°C ≤TJ≤+125°C.(1)(2)(3)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
Dynamic line transient VIN = VOUT(NOM) + 0.3 V to
ΔVOUT ±1 mV
response VIN VOUT(NOM) + 0.9 V; tr, tf = 10 µs
Dynamic line transient VBATT = VOUT(NOM) + 1.5 V to
ΔVOUT ±15 mV
response VBATT VOUT(NOM) + 2.1 V; tr, tf = 10 µs
Pulsed load 0 ...300 mA, DSBGA ±15 mV
di/dt = 300 mA/1 µs package
Dynamic load transient
ΔVOUT response Pulsed load 0 ...300mA, di/dt USON package –35/+15 mV
= 300 mA/1 µs
TSTARTUP Start-up time EN to 0.95 × VOUT 70 150 µs
(1) All voltages are with respect to the potential at the GND pin.
(2) Minimum and maximum limits are ensured by design, test, or statistical analysis. Typical numbers are not ensured, but do represent the
most likely norm. Unless otherwise specified, conditions for typical specifications are: VIN = VOUT(NOM) + 1 V, VBATT = VOUT(NOM) + 1.5 V
or 2.5 V, whichever is higher, TA= 25°C.
(3) VOUT(NOM) is the stated output voltage option.
6.11 Input and Output Capacitors (Recommended)
All values are for TA= 25°C.(1)(2)(3)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
Capacitance(4) 1.5 2.2 10 µF
COUT Output capacitance ESR 3 300 mΩ
Capacitance(4), not needed in typical post- 0.47 1 µF
regulation application (see Figure 18)
CVIN Input capacitance at VIN ESR 3 300 mΩ
(1) All voltages are with respect to the potential at the GND pin.
(2) Minimum and maximum limits are ensured by design, test, or statistical analysis. Typical numbers are not ensured, but do represent the
most likely norm. Unless otherwise specified, conditions for typical specifications are: VIN = VOUT(NOM) + 1 V, VBATT= VOUT(NOM) + 1.5 V
or 2.5 V, whichever is higher, TA= 25°C.
(3) VOUT(NOM) is the stated output voltage option.
(4) The capacitor tolerance should be 30% or better over temperature. The full operating conditions for the application should be considered
when selecting a suitable capacitor to ensure that the minimum value of capacitance is always met. Recommended capacitor type is
X7R. However, dependent on application, X5R, Y5V, and Z5U can also be used. The shown minimum limit represents real minimum
capacitance, including all tolerances and must be maintained over temperature and DC bias voltage (See Detailed Design Procedure in
Application and Implementation.)
Copyright © 2006–2015, Texas Instruments Incorporated Submit Documentation Feedback 7
Product Folder Links: LP5952
2.5 3.0 3.5 4.0 4.5 5.0 5.5
60
70
80
90
100
50
40
30
20
VBATT /VIN (V)
GROUND CURRENT (µA)
2.0 6.0
TA = 125°C
TA = 25°C
TA = -40°C
ILOAD = 0
LOAD CURRENT (mA)
GROUND CURRENT (µA)
2.5 3.0 3.5 4.0 4.5 5.0 5.5
50
60
70
80
90
40
30
20
10
VBATT (V)
IQ_VBATT (µA)
2.0 6.0
TA = 125°C
TA = 25°C
TA = -40°C
ILOAD = 0
VEN
(500 mV/
DIV)
VOUT
(500 mV/
DIV)
TIME (10 Ps/DIV)
0
0
0
IIN
(100 mA/
DIV)
-40 -20 0 20 40 60 80 100 120
100
110
120
130
140
90
80
70
60
TEMPERATURE (°C)
DROPOUT VIN (mV)
TEMPERATURE (°C)
VOUT CHANGE (%)
-40 -20 0 20 40 60 80 100 120
0.0
0.1
0.2
0.3
0.4
-0.1
-0.2
-0.3
-0.4
LP5952
SNVS469F –OCTOBER 2006–REVISED DECEMBER 2015
www.ti.com
6.12 Typical Characteristics
Unless otherwise specified, TA= 25°C, CIN = 1-µF ceramic, COUT = 2.2-µF ceramic, VIN = VOUT(NOM) + 1 V, VBATT = VOUT(NOM) +
1.5 V, EN pin is tied to VBATT (DSBGA package).
ILOAD = 350 mA
Figure 1. Output Voltage Change vs Temperature Figure 2. Dropout VIN vs Temperature
1.5-V Option
Figure 3. Inrush Current VIN Figure 4. Quiescent Current IQ_VBATT vs VBATT
Figure 5. Ground Current vs VBATT / VIN Figure 6. Ground Current vs Load Current
8Submit Documentation Feedback Copyright © 2006–2015, Texas Instruments Incorporated
Product Folder Links: LP5952
100 1k 10k 100k 1M
FREQUENCY (Hz)
-80
-60
-40
-20
0
RIPPLE REJECTION (dB)
10
IL = 0 mA
IL = 50 mA
CIN = 100nF
100 1k 10k 100k 1M
FREQUENCY (Hz)
-80
-60
-40
-20
0
RIPPLE REJECTION (dB)
10
IL = 0 mA
IL = 300 mA
LP5952
www.ti.com
SNVS469F –OCTOBER 2006–REVISED DECEMBER 2015
Typical Characteristics (continued)
Unless otherwise specified, TA= 25°C, CIN = 1-µF ceramic, COUT = 2.2-µF ceramic, VIN = VOUT(NOM) + 1 V, VBATT = VOUT(NOM) +
1.5 V, EN pin is tied to VBATT (DSBGA package).
1.5-V Option 1.5-V Option
Figure 7. Power Supply Rejection Ratio VIN Figure 8. Power Supply Rejection Ratio VBATT
Copyright © 2006–2015, Texas Instruments Incorporated Submit Documentation Feedback 9
Product Folder Links: LP5952
VREF +
-
Enable and
start-up
management
Thermal,
undervoltage, and
overcurrent
protection
EN
GND
BATT IN
OUT
LP5952
SNVS469F –OCTOBER 2006–REVISED DECEMBER 2015
www.ti.com
7 Detailed Description
7.1 Overview
The LP5952 is a dual-supply-rail linear regulator optimized for powering ultralow-voltage circuits from a single Li-
Ion cell or 3 cell NiMH/NiCd batteries. In a typical application, BATT is connected to the battery, and IN can be
supplied by the output of front stage DC-DC Converter. IN does not exceed BATT at any time.
7.2 Functional Block Diagram
7.3 Feature Description
7.3.1 Dual-Rail Supply
The LP5952 requires two different supply voltages:
• VIN, the power input voltage, is regulated to the fixed output voltage.
• VBATT, the bias input voltage, supplies internal circuitry.
It is important that VIN does not exceed VBATT at any time. If the device is used in the typical post-regulation
application as shown in Figure 18, the sequencing of the two power supplies is not an issue because VBATT
supplies both the DC-DC regulator and the LP5952 device. The output voltage of the DC-DC regulator takes
some time to rise up and supply the input voltage of the device. In this application VIN always ramps up more
slowly than VBATT.
If VIN is shorted to VBATT, the voltages at the two supply pins ramp up simultaneously causing no problems.
However, in applications with two independent supplies connected to the LP5952, special care must be taken to
ensure that VIN is always ≤VBATT.
7.3.2 No-Load Stability
The LP5952 remains stable and in regulation with no external load. This is an important consideration in some
circuits, for example, CMOS RAM keep-alive applications.
7.3.3 Fast Turnon
Fast turnon is ensured by an optimized architecture allowing a fast ramp of the output voltage to reach the target
voltage while the inrush current is controlled low at 120 mA typical (for a COUT of 2.2 µF).
10 Submit Documentation Feedback Copyright © 2006–2015, Texas Instruments Incorporated
Product Folder Links: LP5952
LP5952
www.ti.com
SNVS469F –OCTOBER 2006–REVISED DECEMBER 2015
Feature Description (continued)
7.3.4 Short-Circuit Protection
The LP5952 is short-circuit protected and, in the event of a peak overcurrent condition, the output current
through the NFET pass device is limited.
If the overcurrent condition exists for a longer time, the average power dissipation increases depending on the
input-to-output voltage difference until the thermal shutdown circuitry turns the NFET off. Refer to Power
Dissipation and Device Operation for power dissipation calculations.
7.3.5 Thermal-Overload Protection
Thermal-overload protection limits the total power dissipation in the LP5952. When the junction temperature
exceeds TJ= 165°C typical, the shutdown logic is triggered, and the NFET is turned off, allowing the device to
cool down. After the junction temperature dropped by 20°C (temperature hysteresis) typical, the NFET is
activated again. This results in a pulsed output voltage during continuous thermal-overload conditions.
The thermal-overload protection is designed to protect the LP5952 in the event of a fault condition. For normal
continuous operation, do not exceed the absolute maximum junction temperature rating of TJ= 150°C (see
Absolute Maximum Ratings).
7.3.6 Reverse Current Path
The internal NFET pass device in LP5952 has an inherent parasitic body diode. During normal operation, the
input voltage is higher than the output voltage, and the parasitic diode is reverse biased. However, if the output is
pulled above the input in an application, the current flows from the output to the input as the parasitic diode gets
forward biased. The output can be pulled above the input as long as the current in the parasitic diode is limited to
50 mA. For currents above this limit an external Schottky diode must be connected from VOUT to VIN (cathode on
VIN, anode on VOUT).
7.4 Device Functional Modes
7.4.1 Enable Operation
The LP5952 may be switched to an ON or OFF state by a logic input at the EN pin, VEN. A logic high at this pin
turns the device on. When the enable pin is low, the regulator output is off, and the device typically consumes
0.1 µA.
If the application does not require the enable switching feature, the EN pin must be tied to VBATT to keep the
regulator output permanently on.
To ensure proper operation, the signal source used to drive the EN input must be able to swing above and below
the specified turnon and turnoff voltage thresholds shown in VIL and VIH in Electrical Characteristics: Enable
Control.
Copyright © 2006–2015, Texas Instruments Incorporated Submit Documentation Feedback 11
Product Folder Links: LP5952
VBATT: 2.7 V to 5.5 V
IN
OUT
GND
EN
-+
For example,
1.5 V
1 PF
BATT
LP5952
Pre-
regulator
Li-Ion
or
3-cell
NiMh/NiCd
2.2 PF
For example, 1.2 V
A1
B2C3
A3
C1
Load
0 to 350 mA
LP5952
SNVS469F –OCTOBER 2006–REVISED DECEMBER 2015
www.ti.com
8 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
The LP5952 is designed to meet ultralow input-voltage application, by implementing VBATT as power supply of
this device. The VBATT is connected to the battery (range 2.5 V to 5.5 V), the VIN range can be 0.7 V to 4.5 V.
The device offers superior dropout and transient features combined with very low-quiescent currents. The
LP5952 delivers this performance in standard packages DSBGA and USON with an operating junction
temperature (TJ) of –40°C to +125°C.
8.2 Typical Application
8.2.1 Dual-Rail Linear Regulator
Figure 9. LP5952 Typical Application Circuit
8.2.1.1 Design Requirements
For typical dual-rail linear regulator parameters, see Table 1.
Table 1. Design Parameters
DESIGN PARAMETER EXAMPLE VALUE
Input voltage range 0.7 V to 4.5 V
VBATT voltage range 2.7 V to 5.5 V
Output voltage 1.5 V
Output current 350 mA
Output capacitor range 2.2 µF
Input/output capacitor ESR range 3 mΩto 300 mΩ
8.2.1.2 Detailed Design Procedure
8.2.1.2.1 External Capacitors
As is common with most regulators, the LP5952 requires external capacitors to ensure stable operation. The
LP5952 is specifically designed for portable applications requiring minimum board space and the smallest size
components. These capacitors must be correctly selected for good performance.
8.2.1.2.2 Input Capacitor
If the LP5952 is used as a stand-alone device, an input capacitor at VIN is required for stability. It is
recommended that a 1-µF capacitor be connected between the LP5952 power voltage IN pin and ground. (This
capacitance value may be increased without limit).
12 Submit Documentation Feedback Copyright © 2006–2015, Texas Instruments Incorporated
Product Folder Links: LP5952
LP5952
www.ti.com
SNVS469F –OCTOBER 2006–REVISED DECEMBER 2015
This capacitor must be located a distance of not more than 1 cm from the IN pin and returned to a clean analog
ground. Any good quality ceramic, tantalum, or film capacitor may be used at the input.
A capacitor at VBATT is not required if the distance to the supply does not exceed 5 cm.
If the device is used in the typical application as post regulator after a DC-DC regulator, no input capacitors are
required — the capacitors of the DC-DC regulator (CIN and COUT) are sufficient if both components are mounted
close to each other and a proper GND plane is used. If the distance between the output capacitor of the DC-DC
regulator and the IN pin of the LP5952 is larger than 5 cm, adding an input capacitor at VIN is recommended.
NOTE
Important: Tantalum capacitors can suffer catastrophic failures due to surge current
when connected to a low-impedance source of power (like a battery or a very large
capacitor). If a tantalum capacitor is used at the input, it must be ensured by the
manufacturer to have a surge current rating sufficient for the application.
The equivalent series resistance (ESR) of the input capacitor should be in the range of 3 mΩto 300 mΩ. The
tolerance and temperature coefficient must be considered when selecting the capacitor to ensure the
capacitance remains ≥470 nF over the entire operating temperature range.
8.2.1.2.3 Output Capacitor
The LP5952 is designed specifically to work with very small ceramic output capacitors. A ceramic capacitor
(dielectric types X7R, Z5U, or Y5V) in the 2.2-µF range (up to 10 µF) and with an ESR between 3 mΩto 300 mΩ
is suitable as COUT in the LP5952 application circuit.
This capacitor must be located a distance of not more than 1 cm from the OUT pin and returned to a clean
analog ground.
It is also possible to use tantalum or film capacitors at the device output, VOUT, but these are not as attractive for
reasons of size and cost (see Capacitor Characteristics).
8.2.1.2.4 Capacitor Characteristics
The LP5952 is designed to work with ceramic capacitors on the output to take advantage of the benefits they
offer. For capacitance values in the 1-µF to 4.7-µF range, ceramic capacitors are the smallest, least expensive
and have the lowest ESR values, thus making them best for eliminating high-frequency noise. The ESR of a
typical 1-µF ceramic capacitor is in the range of 3 mΩto 40 mΩ, which easily meets the ESR requirement for
stability for the LP5952.
For both input and output capacitors, careful interpretation of the capacitor specification is required to ensure
correct device operation. The capacitor value can change greatly, depending on the operating conditions and
capacitor type.
In particular, the output capacitor selection must take account of all the capacitor parameters, to ensure that the
specification is met within the application. The capacitance can vary with DC bias conditions as well as
temperature and frequency of operation. Capacitor values show some decrease over time due to aging. The
capacitor parameters are also dependant on the particular case size, with smaller sizes giving poorer
performance figures in general. Figure 10 shows a typical graph comparing different capacitor case sizes in a
capacitance vs. DC Bias plot. As shown Figure 10, increasing the DC-bias condition can result in the capacitance
value falling below the minimum value given in Input and Output Capacitors (Recommended) (0.47 µF or 1.5 µF
in this case). The graph shows the capacitance out of specification for the 0402 case size capacitor at higher
bias voltages. It is therefore recommended that the capacitor-manufacturer specifications for the nominal value
capacitor are consulted for all conditions, as some capacitor sizes (such as 0402) may not be suitable in the
actual application.
Copyright © 2006–2015, Texas Instruments Incorporated Submit Documentation Feedback 13
Product Folder Links: LP5952
0 1.0 2.0 3.0 4.0 5.0
CAP VALUE (% of Nom. 1 PF)
DC BIAS (V)
100%
80%
60%
40%
20%
0402, 6.3V, X5R
0603, 10V, X5R
LP5952
SNVS469F –OCTOBER 2006–REVISED DECEMBER 2015
www.ti.com
Figure 10. Typical Variation In Capacitance vs DC Bias
Capacitance of the ceramic capacitor can vary with temperature. The capacitor type X7R, which operates over a
temperature range of –55°C to +125°C, only varies the capacitance to within ±15%. The capacitor type X5R has
a similar tolerance over a reduced temperature range of –55°C to +85°C. Many large value ceramic capacitors,
larger than 1 µF, are manufactured with Z5U or Y5V temperature characteristics. Their capacitance can drop by
more than 50% as the temperature varies from 25°C to 85°C. Therefore, X7R is recommended over Z5U and
Y5V in applications where the ambient temperature changes significantly above or below 25°C.
Tantalum capacitors are less desirable than ceramic for use as output capacitors because they are more
expensive when comparing equivalent capacitance and voltage ratings in the 1-µF to 4.7-µF range.
Another important consideration is that tantalum capacitors have higher ESR values than equivalent size
ceramics. This means that while it may be possible to find a tantalum capacitor with an ESR value within the
stable range, it would have to be larger in capacitance (which means bigger and more costly) than a ceramic
capacitor with the same ESR value. The ESR of a typical tantalum increases about 2:1 as the temperature goes
from 25°C down to –40°C, so some guard band must be allowed.
8.2.1.2.5 Power Dissipation and Device Operation
The permissible power dissipation for any package is a measure of the capability of the device to pass heat from
the power source, the junctions of the device, to the ultimate heat sink, the ambient environment. Thus the power
dissipation is dependent on the ambient temperature and the thermal resistance across the various interfaces
between the die and ambient air.
As stated in the Recommended Operating Conditions, the allowable power dissipation for the device in a given
package can be calculated using Equation 1:
PD= (TJ(MAX) – TA) / RθJA (1)
With an RRθJA = 181°C/W, the device in the 5-pin DSBGA package returns a value of 552 mW with a maximum
junction temperature of 125°C at TAof 25°C or 221 mW at TAof 85°C.
The actual power dissipation across the device can be estimated by Equation 2:
PD= (VIN – VOUT)×IOUT (2)
14 Submit Documentation Feedback Copyright © 2006–2015, Texas Instruments Incorporated
Product Folder Links: LP5952
VIN - VOUT (V)
ILOADMAX (mA)
0 0.5 1 1.5 2 2.5 3 3.5 4
50
100
150
200
250
300
350
D001
DSBGA
USON
LP5952
www.ti.com
SNVS469F –OCTOBER 2006–REVISED DECEMBER 2015
This establishes the relationship between the power dissipation allowed due to thermal consideration, the voltage
drop across the device, and the continuous current capability of the device. Equation 1 and Equation 2 must be
used to determine the optimum operating conditions for the device in any application. As an example, to keep full
load current capability of 350 mA for a 1.5-V output voltage option at a high ambient temperature of 85°C, VIN
has to be kept ≤2.1 V (for DSBGA package):
VIN ≤PD/ IOUT + VOUT = 221 mW / 350 mA + 1.5 V = 2.1 V (3)
Figure 11 shows the output current derating due to these considerations:
TA= 85°C VOUT = 1.5 V
RθJA(DSBGA) = 181°C/W RθJA(USON) = 181.6°C/W
Figure 11. Maximum Load Current vs VIN – VOUT
The typical contribution of the bias input voltage supply VBATT to the power dissipation can be neglected
(Equation 4):
PD_VBATT = VBATT × IQVBATT = 5.5 V × 50 µA = 0.275 mW typical (4)
Copyright © 2006–2015, Texas Instruments Incorporated Submit Documentation Feedback 15
Product Folder Links: LP5952
VIN
(500 mV/DIV)
3.1
ÂVOUT
(1 mV/DIV)
2.5
TIME (100 Ps/DIV)
IL = 350 mA
VBATT = 3.1V
VBATT
(500 mV/DIV)
3.6
ÂVOUT
(10 mV/DIV)
3.0
TIME (100 Ps/DIV)
IL = 350 mA
LOAD CURRENT (mA)
0
350
ÂVOUT
(10 mV/DIV)
TIME (50 µs/DIV)
LOAD CURRENT (mA)
0
350
ÂVOUT
(10 mV/DIV)
TIME (50 µs/DIV)
VEN
(500 mV/DIV)
VOUT
(200 mV/DIV)
TIME (10 µs/DIV)
IL = 350 mA
0
0
VEN
(500 mV/DIV)
VOUT
(500 mV/DIV)
TIME (10 µs/DIV)
IL = 350 mA
0
0
LP5952
SNVS469F –OCTOBER 2006–REVISED DECEMBER 2015
www.ti.com
8.2.1.3 Application Curves
0.7-V Option 1.5-V Option
Figure 12. Enable Start-Up Time Figure 13. Enable Start-Up Time
0.7-V Option 1.5-V Option
Figure 14. Load Transient Response Figure 15. Load Transient Response
1.5-V Option 1.5-V Option
Figure 16. Line Transient Response VIN Figure 17. Line Transient Response VBATT
16 Submit Documentation Feedback Copyright © 2006–2015, Texas Instruments Incorporated
Product Folder Links: LP5952
VIN SW
FB
EN
GND
L1: 2.2 PH10 PF
4.7 PFLM3671TL-1.8
VBATT
3 V to 5.5 V IN
OUT
GND
Load
0 to 350 mA
BATT
LP5952
1.5 V
EN
2.2 PF
A1
B2
C3
A3
C1
1.8 V
VOUTDCDC
A1
A3
C1 C3
B2
LP5952
www.ti.com
SNVS469F –OCTOBER 2006–REVISED DECEMBER 2015
8.2.2 Additional Application Circuit
Figure 18. Typical Application Circuit With DC-DC Converter as Pre-Regulator for VIN
9 Power Supply Recommendations
This device is designed to operate from an input supply voltage range of 0.7 V to 4.5 V. The input supply should
be well regulated and free of spurious noise. A minimum capacitor value of 1-μF is required to be within 1 cm of
the IN pin. The VBATT range is 2.5 V to 5.5 V and, in the typical application, VBATT is connected to batteries. In
any application, VIN does not exceed VBATT.
Copyright © 2006–2015, Texas Instruments Incorporated Submit Documentation Feedback 17
Product Folder Links: LP5952
1
2
3
6
5
4
BATT
GND
IN
EN
NC
OUT
CIN
CBATT
COUT
CIN CBATT
OUT
IN GND
A3
A1 BATT
B2
C3
C1
OUT2
EN
COUT
LP5952
SNVS469F –OCTOBER 2006–REVISED DECEMBER 2015
www.ti.com
10 Layout
10.1 Layout Guidelines
For best overall performance, place all circuit components on the same side of the circuit board and as near to
the respective LDO pin connections as practical. Place ground return connections as close as possible to the
input and output capacitor and to the LDO ground pin, connected by a wide, copper surface. The use of vias and
long traces to create LDO circuit connection is strongly discouraged and negatively affect system performance.
10.2 Layout Examples
Figure 19. LP5952 DSBGA Layout Example
Figure 20. LP5952 WSON Layout Example
18 Submit Documentation Feedback Copyright © 2006–2015, Texas Instruments Incorporated
Product Folder Links: LP5952
LP5952
www.ti.com
SNVS469F –OCTOBER 2006–REVISED DECEMBER 2015
11 Device and Documentation Support
11.1 Device Support
For availability of evaluation boards, refer to the product folder of LP5952 at www.ti.com.
11.2 Documentation Support
11.2.1 Related Documentation
For information regarding evaluation boards, please refer to AN-1531 LP5952 Evaluation Board (SNVA188).
11.3 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
11.4 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
11.5 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
11.6 Glossary
SLYZ022 —TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Copyright © 2006–2015, Texas Instruments Incorporated Submit Documentation Feedback 19
Product Folder Links: LP5952
PACKAGE OPTION ADDENDUM
www.ti.com 23-Aug-2017
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LP5952LC-1.2/NOPB ACTIVE USON NKH 6 1000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 L28
LP5952LC-1.3/NOPB ACTIVE USON NKH 6 1000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 L43
LP5952LC-1.5/NOPB ACTIVE USON NKH 6 1000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 L25
LP5952LC-1.8/NOPB ACTIVE USON NKH 6 1000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 125 L29
LP5952TL-1.0/NOPB ACTIVE DSBGA YZR 5 250 Green (RoHS
& no Sb/Br) SNAGCU Level-1-260C-UNLIM -40 to 125 L
LP5952TL-1.2/NOPB ACTIVE DSBGA YZR 5 250 Green (RoHS
& no Sb/Br) SNAGCU Level-1-260C-UNLIM -40 to 125 7
LP5952TL-1.3/NOPB ACTIVE DSBGA YZR 5 250 Green (RoHS
& no Sb/Br) SNAGCU Level-1-260C-UNLIM -40 to 125 U
LP5952TL-1.5/NOPB ACTIVE DSBGA YZR 5 250 Green (RoHS
& no Sb/Br) SNAGCU Level-1-260C-UNLIM -40 to 125 T
LP5952TL-1.6/NOPB ACTIVE DSBGA YZR 5 250 Green (RoHS
& no Sb/Br) SNAGCU Level-1-260C-UNLIM -40 to 125 B
LP5952TL-1.8/NOPB ACTIVE DSBGA YZR 5 250 Green (RoHS
& no Sb/Br) SNAGCU Level-1-260C-UNLIM -40 to 125 8
LP5952TLX-1.0/NOPB ACTIVE DSBGA YZR 5 3000 Green (RoHS
& no Sb/Br) SNAGCU Level-1-260C-UNLIM -40 to 125 L
LP5952TLX-1.2/NOPB ACTIVE DSBGA YZR 5 3000 Green (RoHS
& no Sb/Br) SNAGCU Level-1-260C-UNLIM -40 to 125 7
LP5952TLX-1.5/NOPB ACTIVE DSBGA YZR 5 3000 Green (RoHS
& no Sb/Br) SNAGCU Level-1-260C-UNLIM -40 to 125 T
LP5952TLX-1.8/NOPB ACTIVE DSBGA YZR 5 3000 Green (RoHS
& no Sb/Br) SNAGCU Level-1-260C-UNLIM -40 to 125 8
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
PACKAGE OPTION ADDENDUM
www.ti.com 23-Aug-2017
Addendum-Page 2
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
LP5952LC-1.2/NOPB USON NKH 6 1000 178.0 12.4 2.2 2.2 1.0 8.0 12.0 Q1
LP5952LC-1.3/NOPB USON NKH 6 1000 178.0 12.4 2.2 2.2 1.0 8.0 12.0 Q1
LP5952LC-1.5/NOPB USON NKH 6 1000 178.0 12.4 2.2 2.2 1.0 8.0 12.0 Q1
LP5952LC-1.8/NOPB USON NKH 6 1000 178.0 12.4 2.2 2.2 1.0 8.0 12.0 Q1
LP5952TL-1.0/NOPB DSBGA YZR 5 250 178.0 8.4 1.04 1.4 0.76 4.0 8.0 Q1
LP5952TL-1.2/NOPB DSBGA YZR 5 250 178.0 8.4 1.04 1.4 0.76 4.0 8.0 Q1
LP5952TL-1.3/NOPB DSBGA YZR 5 250 178.0 8.4 1.04 1.4 0.76 4.0 8.0 Q1
LP5952TL-1.5/NOPB DSBGA YZR 5 250 178.0 8.4 1.04 1.4 0.76 4.0 8.0 Q1
LP5952TL-1.6/NOPB DSBGA YZR 5 250 178.0 8.4 1.04 1.4 0.76 4.0 8.0 Q1
LP5952TL-1.8/NOPB DSBGA YZR 5 250 178.0 8.4 1.04 1.4 0.76 4.0 8.0 Q1
LP5952TLX-1.0/NOPB DSBGA YZR 5 3000 178.0 8.4 1.04 1.4 0.76 4.0 8.0 Q1
LP5952TLX-1.2/NOPB DSBGA YZR 5 3000 178.0 8.4 1.04 1.4 0.76 4.0 8.0 Q1
LP5952TLX-1.5/NOPB DSBGA YZR 5 3000 178.0 8.4 1.04 1.4 0.76 4.0 8.0 Q1
LP5952TLX-1.8/NOPB DSBGA YZR 5 3000 178.0 8.4 1.04 1.4 0.76 4.0 8.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 24-Aug-2017
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LP5952LC-1.2/NOPB USON NKH 6 1000 210.0 185.0 35.0
LP5952LC-1.3/NOPB USON NKH 6 1000 210.0 185.0 35.0
LP5952LC-1.5/NOPB USON NKH 6 1000 210.0 185.0 35.0
LP5952LC-1.8/NOPB USON NKH 6 1000 210.0 185.0 35.0
LP5952TL-1.0/NOPB DSBGA YZR 5 250 210.0 185.0 35.0
LP5952TL-1.2/NOPB DSBGA YZR 5 250 210.0 185.0 35.0
LP5952TL-1.3/NOPB DSBGA YZR 5 250 210.0 185.0 35.0
LP5952TL-1.5/NOPB DSBGA YZR 5 250 210.0 185.0 35.0
LP5952TL-1.6/NOPB DSBGA YZR 5 250 210.0 185.0 35.0
LP5952TL-1.8/NOPB DSBGA YZR 5 250 210.0 185.0 35.0
LP5952TLX-1.0/NOPB DSBGA YZR 5 3000 210.0 185.0 35.0
LP5952TLX-1.2/NOPB DSBGA YZR 5 3000 210.0 185.0 35.0
LP5952TLX-1.5/NOPB DSBGA YZR 5 3000 210.0 185.0 35.0
LP5952TLX-1.8/NOPB DSBGA YZR 5 3000 210.0 185.0 35.0
PACKAGE MATERIALS INFORMATION
www.ti.com 24-Aug-2017
Pack Materials-Page 2
MECHANICAL DATA
NKH0006B
www.ti.com
LCA06B (Rev A)
MECHANICAL DATA
YZR0005xxx
www.ti.com
TLA05XXX (Rev C)
0.600±0.075
D
E
NOTES:
A
. All linear dimensions are in millimeters. Dimensioning and tolerancing per ASME Y14.5M-1994.
B. This drawing is subject to change without notice.
4215043/A 12/12
D: Max =
E: Max =
1.356 mm, Min =
0.99 mm, Min =
1.296 mm
0.93 mm
IMPORTANT NOTICE
Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its
semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers
should obtain the latest relevant information before placing orders and should verify that such information is current and complete.
TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated
circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and
services.
Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced
documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements
different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the
associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers
remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have
full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products
used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with
respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous
consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and
take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will
thoroughly test such applications and the functionality of such TI products as used in such applications.
TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,
including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to
assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any
way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource
solely for this purpose and subject to the terms of this Notice.
TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI
products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,
enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically
described in the published documentation for a particular TI Resource.
Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that
include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE
TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY
RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or
endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR
REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO
ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,
INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF
PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,
DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN
CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949
and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.
Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such
products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards
and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must
ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in
life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.
Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life
support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all
medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.
TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).
Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications
and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory
requirements in connection with such selection.
Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s non-
compliance with the terms and provisions of this Notice.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2017, Texas Instruments Incorporated
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Texas Instruments:
LP5952LC-1.2/NOPB LP5952LC-1.3/NOPB LP5952LC-1.5/NOPB LP5952LC-1.8/NOPB LP5952LC-1.8EV
LP5952LCX-1.2/NOPB LP5952LCX-1.3/NOPB LP5952LCX-1.5/NOPB LP5952LCX-1.8/NOPB LP5952TL-0.7/NOPB
LP5952TL-1.0/NOPB LP5952TL-1.2/NOPB LP5952TL-1.3/NOPB LP5952TL-1.4/NOPB LP5952TL-1.5/NOPB
LP5952TL-1.6/NOPB LP5952TL-1.8/NOPB LP5952TL-2.0/NOPB LP5952TLX-0.7/NOPB LP5952TLX-1.0/NOPB
LP5952TLX-1.2/NOPB LP5952TLX-1.3/NOPB LP5952TLX-1.4/NOPB LP5952TLX-1.5/NOPB LP5952TLX-1.6/NOPB
LP5952TLX-1.8/NOPB LP5952TLX-2.0/NOPB
