NEW DMF Series Metallized Polyester / Radial Leads Maximum Pulse Rise Time (dv/dt) Vn 63V 100V 250V 400V 630V 7.5 4 7 12 23 35 (Pitch mm) 15 20 1.5 3 2 7 4 10 5.5 15 8 10 3 6 11 20 30 . GENERAL SPECIFICATIONS Dielectric Withstand Voltage: Operating Temperature: 1.6 x Rated Voltage for 2 sec at -40C to +100C with voltage +25C 5C derating above 85C Dissipation Factor (DF): Voltage Range: tg x 10-4 at +25C 5C 63 VDC to 630 VDC Capacitance Range: kHz C .1F .1C 1F C1 0.01 F to 10 F 1 80 80 100 Capacitance Tolerance: 10 150 150 180 5%, 10%, 20% Total Self Inductance (L): Pitch (mm) L (nH) 7.5 6 10 9 15 10 20 17 27.5 32.5 37.5 18 22 23 Test Method and Performance Insulation Resistance 27.5 32.5 1 3 5 7 2 4 5 37.5 1 2 3 If the working voltage (V) is less than the nominal voltage (Vn), the capacitor can work at higher dv/dt. In this case, the maximum value allowed is obtained by multiplying the above value (See table dv/dt) with the ratio Vn/V. Outline Dimensions Test Conditions Temperature Voltage Charge Time Voltage Charge Performance for C 0.1F for C 0.1F 25C 5C 1 minute 100 VDC 2X105 M 2X104 M Damp Heat Test Test Conditions Temperature Relative Humidity Test Duration Performance Capacitance Change C/C DF Change tg Insulation Resistance +40C 95% 46 days 5% 50 x 104 at 1kHz 50% of limit value Life Test L Max L Max T Max H Max H Max Test Conditions Temperature Test Duration Voltage Applied Performance Capacitance ChangeC/C DF Change tg Insulation Resistance +85C 2000 hrs 1.25 x Vn 5% 30 x 10-4 at 1kHz 50% of limit value Soldering (5mm 1) Test Conditions Soldering Temperature Soldering Duration Performance Capacitance Change C/C DF Change tg (35mm) Max. (4.5mm 0.5) S ( 0.5mm) S ( 1.0mm) 260C 5C 10 sec 1 sec 1% 30 x 10-4 at 1kHz d ( 0.02mm) Long Term Stability (after two years) Storage Performance Capacitance Change C/C Standard Environmental Conditions 3% Mallory Products for CDE/6325 Digital Way/Indianapolis IN 46278/Phone: (317)275-2285/Fax: (317)275-2293/www.cornell-dubilier.com 189 Film Capacitors Radial Leaded (7.5 mm to 42.5 mm) Non Inductively Wound Non-Polar Flame Retardant Epoxy Powder Coating Meets UL94V-0 Lead Material Tinned Copper Clad Steel Excellent choice for general purpose applications such as bypass, decoupling, smoothing and some timing, energy storage/ discharge and arc suppression. NEW DMF Series Metallized Polyester / Radial Leads Film Capacitors Inches Catalog Number Cap F L Millimeters T H S d L T H S d 9.0 9.5 9.5 9.5 9.5 9.5 9.5 10.5 10.5 11.0 11.5 11.5 12.5 14.0 15.0 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 10.0 10.0 15.0 15.0 .6 .6 .6 .6 .6 .6 .6 .6 .6 .6 .6 .6 .6 .8 .8 9.0 9.5 9.5 9.5 9.5 9.5 9.5 9.0 10.0 11.5 11.0 12.5 13.5 14.5 16.5 20.0 21.5 23.5 29.0 7.5 7.5 7.5 7.5 7.5 7.5 7.5 10.0 10.0 10.0 15.0 15.0 15.0 20.0 20.0 20.0 20.0 27.5 27.5 63 VDC/40 VAC DMF103*063A DMF153*063A DMF223*063A DMF333*063A DMF473*063A DMF683*063A DMF104*063A DMF154*063A DMF224*063A DMF334*063A DMF474*063A DMF684*063B DMF105*063B DMF155*063C DMF225*063C .01 .015 .022 .033 .047 .068 .1 .15 .22 .33 .47 .68 1.0 1.5 2.2 .413 .413 .413 .413 .413 .413 .413 .413 .413 .413 .413 .512 .512 .728 .728 .217 .236 .236 .236 .236 .236 .236 .276 .276 .315 .315 .276 .276 .315 .394 .354 .374 .374 .374 .374 .374 .374 .413 .413 .433 .453 .453 .492 .551 .591 .295 .295 .295 .295 .295 .295 .295 .295 .295 .295 .295 .394 .394 .591 .591 .024 .024 .024 .024 .024 .024 .024 .024 .024 .024 .024 .024 .024 .031 .031 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 10.5 13.0 13.0 18.5 18.5 5.5 6.0 6.0 6.0 6.0 6.0 6.0 7.0 7.0 8.0 8.0 7.0 7.0 8.0 10.0 100 VDC/63 VAC DMF103*100A DMF153*100A DMF223*100A DMF333*100A DMF473*100A DMF683*100A DMF104*100A DMF154*100B DMF224*100B DMF334*100B DMF474*100C DMF684*100C DMF105*100C DMF155*100D DMF225*100D DMF335*100D DMF475*100D DMF685*100E DMF106*100E .01 .015 .022 .033 .047 .068 .1 .15 .22 .33 .47 .68 1.0 1.5 2.2 3.3 4.7 6.8 10.0 .394 .413 .413 .413 .413 .413 .413 .512 .512 .512 .728 .728 .728 .886 .886 .886 .886 1.260 1.260 .217 .236 .236 .236 .236 .236 .236 .217 .256 .315 .236 .295 .335 .315 .394 .472 .551 .571 .709 .354 .374 .374 .374 .374 .374 .374 .354 .394 .453 .433 .492 .531 .571 .650 .787 .846 .925 1.142 .295 .295 .295 .295 .295 .295 .295 .394 .394 .394 .591 .591 .591 .787 .787 .787 .787 1.083 1.083 .024 .024 .024 .024 .024 .024 .024 .024 .024 .024 .024 .024 .031 .031 .031 .031 .031 .031 .031 10.0 10.5 10.5 10.5 10.5 10.5 10.5 13.0 13.0 13.0 18.5 18.5 18.5 22.5 22.5 22.5 22.5 32.0 32.0 5.5 6.0 6.0 6.0 6.0 6.0 6.0 5.5 6.5 8.0 6.0 7.5 8.5 8.0 10.0 12.0 14.0 14.5 18.0 .6 .6 .6 .6 .6 .6 .6 .6 .6 .6 .6 .6 .8 .8 .8 .8 .8 .8 .8 250 VDC/160 VAC DMF103*250A DMF153*250A DMF223*250A DMF333*250A DMF473*250A DMF683*250A DMF104*250B DMF154*250C DMF224*250C DMF334*250C DMF474*250D DMF684*250D DMF105*250D DMF155*250E DMF225*250E DMF335*250E DMF475*250F DMF685*250G DMF106*250G .01 .015 .022 .033 .047 .068 .1 .15 .22 .33 .47 .68 1.0 1.5 2.2 3.3 4.7 6.8 10.0 .413 .413 .413 .413 .413 .413 .512 .728 .728 .728 .886 .886 .886 1.260 1.260 1.260 1.417 1.654 1.654 0.217 0.236 0.236 0.236 0.236 0.256 0.256 0.236 0.256 0.276 0.295 0.335 0.394 0.374 0.413 0.531 0.551 0.630 0.748 .354 .374 .374 .374 .374 .394 .394 .433 .453 .472 .492 .531 .591 .689 .748 .906 .945 1.063 1.378 .295 .295 .295 .295 .295 .295 .394 .591 .591 .591 .787 .787 .787 1.083 1.083 1.083 1.280 1.476 1.476 .024 .024 .024 .024 .024 .024 .024 .024 .024 .031 .031 .031 .031 .031 .031 .031 .031 .039 .039 10.5 10.5 10.5 10.5 10.5 10.5 13.0 18.5 18.5 18.5 22.5 22.5 22.5 32.0 32.0 32.0 36.0 42.0 42.0 5.5 6.0 6.0 6.0 6.0 6.5 6.5 6.0 6.5 7.0 7.5 8.5 10.0 9.5 10.5 13.5 14.0 16.0 19.0 9.0 9.5 9.5 9.5 9.5 10.0 10.0 11.0 11.5 12.0 12.5 13.5 15.0 17.5 19.0 23.0 24.0 27.0 35.0 7.5 7.5 7.5 7.5 7.5 7.5 10.0 15.0 15.0 15.0 20.0 20.0 20.0 27.5 27.5 27.5 32.5 37.5 37.5 * Indicate capacitance tolerance: J = 5%, K = 10%, M = 20% Note: Add "TA" to end of part number for Tape and Ammo 190 Mallory Products for CDE/6325 Digital Way/Indianapolis IN 46278/Phone: (317)275-2285/Fax: (317)275-2293/www.cornell-dubilier.com .6 .6 .6 .6 .6 .6 .6 .6 .6 .8 .8 .8 .8 .8 .8 .8 .8 1.0 1.0 EW N DMF Series Metallized Polyester / Radial Leads Inches Cap F L Millimeters T H S d L T H S d 400 VDC/200 VAC DMF103*400A DMF153*400A DMF223*400B DMF333*400B DMF473*400B DMF683*400B DMF104*400C DMF154*400C DMF224*400D DMF334*400D DMF474*400D DMF684*400E DMF105*400E DMF155*400F DMF225*400F DMF335*400G DMF475*400H .01 .015 .022 .033 .047 .068 .1 .15 .22 .33 .47 .68 1.0 1.5 2.2 3.3 4.7 .413 .413 .512 .512 .512 .512 .728 .728 .886 .886 .886 1.260 1.260 1.417 1.417 1.654 1.811 .217 .236 .236 .256 .276 .315 .276 .315 .315 .354 .453 .472 .531 .551 .728 .728 .866 .354 .374 .374 .394 .472 .512 .492 .531 .571 .591 .728 .748 .846 .925 1.083 1.201 1.339 DMF103*630B DMF153*630B DMF223*630B DMF333*630C DMF473*630C DMF683*630C DMF104*630C DMF154*630D DMF224*630D DMF334*630E DMF474*630E DMF684*630F DMF105*630F DMF155*630G DMF225*630H .01 .015 .022 .033 .047 .068 .1 .15 .22 .33 .47 .68 1.0 1.5 2.2 .512 .512 .512 .728 .728 .728 .728 .886 .886 1.260 1.260 1.417 1.417 1.654 1.811 .236 .256 .295 .256 .295 .335 .394 .374 .453 .472 .531 .571 .630 .728 .807 .394 .413 .492 .472 .492 .551 .571 .650 .748 .748 .866 .886 1.142 1.161 1.280 .295 .295 .394 .394 .394 .394 .591 .591 .787 .787 .787 1.083 1.083 1.280 1.280 1.476 1.673 .024 .024 .024 .024 .024 .024 .031 .031 .031 .031 .031 .031 .031 .031 .031 .039 .039 10.5 10.5 13.0 13.0 13.0 13.0 18.5 18.5 22.5 22.5 22.5 32.0 32.0 36.0 36.0 42.0 46.0 5.5 6.0 6.0 6.5 7.0 8.0 7.0 8.0 8.0 9.0 11.5 12.0 13.5 14.0 18.5 18.5 22.0 9.0 9.5 9.5 10.0 12.0 13.0 12.5 13.5 14.5 15.0 18.5 19.0 21.5 23.5 27.5 30.5 34.0 7.5 7.5 10.0 10.0 10.0 10.0 15.0 15.0 20.0 20.0 20.0 27.5 27.5 32.5 32.5 37.5 42.5 .6 .6 .6 .6 .6 .6 .8 .8 .8 .8 .8 .8 .8 .8 .8 1.0 1.0 13.0 13.0 13.0 18.5 18.5 18.5 18.5 22.5 22.5 32.0 32.0 36.0 36.0 42.0 46.0 6.0 6.5 7.5 6.5 7.5 8.5 10.0 9.5 11.5 12.0 13.5 14.5 16.0 18.5 20.5 10.0 10.5 12.5 12.0 12.5 14.0 14.5 16.5 19.0 19.0 22.0 22.5 29.0 29.5 32.5 10.0 10.0 10.0 15.0 15.0 15.0 15.0 20.0 20.0 27.5 27.5 32.5 32.5 37.5 42.5 .6 .6 .6 .6 .6 .8 .8 .8 .8 .8 .8 .8 .8 1.0 1.0 630 VDC/220 VAC .394 .394 .394 .591 .591 .591 .591 .787 .787 1.083 1.083 1.280 1.280 1.476 1.673 .024 .024 .024 .024 .024 .031 .031 .031 .031 .031 .031 .031 .031 .039 .039 * Indicate capacitance tolerance: J = 5%, K = 10%, M = 20% Note: Add "TA" to end of part number for Tape and Ammo Mallory Products for CDE/6325 Digital Way/Indianapolis IN 46278/Phone: (317)275-2285/Fax: (317)275-2293/www.cornell-dubilier.com 191 Film Capacitors Catalog Number NEW DMF Series Metallized Polyester / Radial Leads P1 h d 360 mm Max 14.17" W0 W W1 H W2 Film Capacitors P3 P P0 P2 55 mm Max 2.17" D0 340 mm Max 13.39" Component Quantity Per Ammo Pack Dimensions Millimeters Ammo Box Packing Item Code Lead-Wire Diameter Lead-to-Lead Distance Feed Hole Pitch Pitch of Component Hole Center to Lead Feed Hole Center to Component Center Component Alignment, F-R Tape Width Hold-Down Tape Width Hole Position d P p0 p1 p2 p3 0.6.05 h W W0 W1 02.0 18+1.0-0.5 12.5 min 9.0+0.5 0.079 .709+.039-.020 .492 min .354.020 Hold-Down Tape Position Height of Component from Tape Center Feed Hole Diameter W2 H 3.0 Max 16.00.5 .118 Max .630.02 D0 4.00.2 .157.008 Quantity Ammo Pack Case Code Inches .024.002 SEE CHART 12.70.3 .5.012 SEE CHART 3.850.7 .152.028 6.351.3 .250.051 A B C D Size Code A B C D 1000 800 300 200 P Dimension p1 Dimension Millimeters Inches +.031-.008 1.0 .040 .197 .197 .295 .295 12.7 15.0 25.4 25.4 .500 .591 1.0 1.0 Millimeters Inches +0.8-0.2 5.0 5.0 7.5 7.5 *Taping not available for lead spacing greater than 20.0mm or .780in. 192 Mallory Products for CDE/6325 Digital Way/Indianapolis IN 46278/Phone: (317)275-2285/Fax: (317)275-2293/www.cornell-dubilier.com