DMF155M063CTA - Cornell Dubilier Electronics, Inc.

189

Mallory Products for CDE/6325 Digital Way/Indianapolis IN 46278/Phone: (317)275-2285/Fax: (317)275-2293/www.cornell-dubilier.com

Film CapacitorsFilm Capacitors

Film Capacitors

.GENERAL

SPECIFICATIONS

Operating Temperature:

-40쎷C to +100 쎷C with voltage

derating above 85쎷C

Voltage Range:

63 VDC to 630 VDC

Capacitance Range:

0.01 애F to 10 애F

Capacitance Tolerance:

앧5%, 앧10%, 앧20%

쏋Radial Leaded

(7.5 mm to 42.5 mm)

쏋Non Inductively Wound

쏋Non-Polar

쏋Flame Retardant Epoxy

Powder

쏋Coating Meets UL94V-0

쏋Lead Material

Tinned Copper Clad Steel

Excellent choice for general

purpose applications such as

bypass, decoupling, smoothing

and some timing, energy storage/

discharge and arc suppression.

Insulation Resistance

Test Conditions

Temperature 25쎷C 앧5쎷C

Voltage Charge Time 1 minute

Voltage Charge 100 VDC

Performance

for C 울 0.1애F욷2X105 M⏲

for C 쏜 0.1애F욷2X104 M⏲

Damp Heat Test

Test Conditions

Temperature +40쎷C

Relative Humidity 95%

Test Duration 46 days

Performance

Capacitance Change 욼C/C 울 앧 5%

DF Change 욼tg웃울 50 x 104 at 1kHz

Insulation Resistance 욷 50% of limit value

Life Test

Test Conditions

Temperature +85쎷C

Test Duration 2000 hrs

Voltage Applied 1.25 x Vn

Performance

Capacitance Change욼C/C 울 앧 5%

DF Change 욼tg웃울 30 x 10-4 at 1kHz

Insulation Resistance 욷 50% of limit value

Soldering

Test Conditions

Soldering Temperature 260쎷C 앧 5쎷C

Soldering Duration 10 sec 앧 1 sec

Performance

Capacitance Change 욼C/C 울 앧 1%

DF Change 욼tg웃욷30 x 10-4 at 1kHz

Long Term Stability (after two years)

Storage

Standard Environmental Conditions

Performance

Capacitance Change 욼C/C 울 앧 3%

Test Method and Performance

Total Self Inductance (L):

Pitch (mm) 7.5 10 15 20 27.5 32.5 37.5

L (nH) 앒6 9 10 17 18 22 23

kHz C 울.1애F .1쏝C 울1애FC욷1

1울80 울80 울100

10 울150 울150 울180

Maximum

Pulse Rise Time (dv/dt)

(Pitch mm)

Vn 7.5 10 15 20 27.5 32.5 37.5

63V 4 3 1.5

100V 7 6 3 2 1

250V 12 11 7 4 3 2 1

400V 23 20 10 5.5 5 4 2

630V 35 30 15 8 7 5 3

If the working voltage (V) is less than the nominal voltage (Vn), the

capacitor can work at higher dv/dt. In this case, the maximum value

allowed is obtained by multiplying the above value (See table dv/dt) with

the ratio Vn/V.

Outline Dimensions

DMF Series

Metallized Polyester / Radial Leads

Dielectric Withstand Voltage:

1.6 x Rated Voltage for 2 sec at

+25쎷C 앧5쎷C

Dissipation Factor (DF):

tg웃 x 10-4 at +25쎷C 앧5쎷C

(35mm)

Max.

Max

(앐 0.5mm)

(4.5mm 앐 0.5)

Max

(5mm 앐 1)

(앐 1.0mm) d

(앐 0.02mm)

쐀

NEW

190Mallory Products for CDE/6325 Digital Way/Indianapolis IN 46278/Phone: (317)275-2285/Fax: (317)275-2293/www.cornell-dubilier.com

Film CapacitorsFilm Capacitors

Film Capacitors

DMF Series

Metallized Polyester / Radial Leads

Cap

애애

애FLTH 얒얒

얒얒

얒dSL

MillimetersInches

THS얒얒

얒얒

얒d

63 VDC/40 VAC

100 VDC/63 VAC

DMF103*100A .01 .394 .217 .354 .295 .024 10.0 5.5 9.0 7.5 .6

DMF153*100A .015 .413 .236 .374 .295 .024 10.5 6.0 9.5 7.5 .6

DMF223*100A .022 .413 .236 .374 .295 .024 10.5 6.0 9.5 7.5 .6

DMF333*100A .033 .413 .236 .374 .295 .024 10.5 6.0 9.5 7.5 .6

DMF473*100A .047 .413 .236 .374 .295 .024 10.5 6.0 9.5 7.5 .6

DMF683*100A .068 .413 .236 .374 .295 .024 10.5 6.0 9.5 7.5 .6

DMF104*100A .1 .413 .236 .374 .295 .024 10.5 6.0 9.5 7.5 .6

DMF154*100B .15 .512 .217 .354 .394 .024 13.0 5.5 9.0 10.0 .6

DMF224*100B .22 .512 .256 .394 .394 .024 13.0 6.5 10.0 10.0 .6

DMF334*100B .33 .512 .315 .453 .394 .024 13.0 8.0 11.5 10.0 .6

DMF474*100C .47 .728 .236 .433 .591 .024 18.5 6.0 11.0 15.0 .6

DMF684*100C .68 .728 .295 .492 .591 .024 18.5 7.5 12.5 15.0 .6

DMF105*100C 1.0 .728 .335 .531 .591 .031 18.5 8.5 13.5 15.0 .8

DMF155*100D 1.5 .886 .315 .571 .787 .031 22.5 8.0 14.5 20.0 .8

DMF225*100D 2.2 .886 .394 .650 .787 .031 22.5 10.0 16.5 20.0 .8

DMF335*100D 3.3 .886 .472 .787 .787 .031 22.5 12.0 20.0 20.0 .8

DMF475*100D 4.7 .886 .551 .846 .787 .031 22.5 14.0 21.5 20.0 .8

DMF685*100E 6.8 1.260 .571 .925 1.083 .031 32.0 14.5 23.5 27.5 .8

DMF106*100E 10.0 1.260 .709 1.142 1.083 .031 32.0 18.0 29.0 27.5 .8

250 VDC/160 VAC

DMF103*250A .01 .413 0.217 .354 .295 .024 10.5 5.5 9.0 7.5 .6

DMF153*250A .015 .413 0.236 .374 .295 .024 10.5 6.0 9.5 7.5 .6

DMF223*250A .022 .413 0.236 .374 .295 .024 10.5 6.0 9.5 7.5 .6

DMF333*250A .033 .413 0.236 .374 .295 .024 10.5 6.0 9.5 7.5 .6

DMF473*250A .047 .413 0.236 .374 .295 .024 10.5 6.0 9.5 7.5 .6

DMF683*250A .068 .413 0.256 .394 .295 .024 10.5 6.5 10.0 7.5 .6

DMF104*250B .1 .512 0.256 .394 .394 .024 13.0 6.5 10.0 10.0 .6

DMF154*250C .15 .728 0.236 .433 .591 .024 18.5 6.0 11.0 15.0 .6

DMF224*250C .22 .728 0.256 .453 .591 .024 18.5 6.5 11.5 15.0 .6

DMF334*250C .33 .728 0.276 .472 .591 .031 18.5 7.0 12.0 15.0 .8

DMF474*250D .47 .886 0.295 .492 .787 .031 22.5 7.5 12.5 20.0 .8

DMF684*250D .68 .886 0.335 .531 .787 .031 22.5 8.5 13.5 20.0 .8

DMF105*250D 1.0 .886 0.394 .591 .787 .031 22.5 10.0 15.0 20.0 .8

DMF155*250E 1.5 1.260 0.374 .689 1.083 .031 32.0 9.5 17.5 27.5 .8

DMF225*250E 2.2 1.260 0.413 .748 1.083 .031 32.0 10.5 19.0 27.5 .8

DMF335*250E 3.3 1.260 0.531 .906 1.083 .031 32.0 13.5 23.0 27.5 .8

DMF475*250F 4.7 1.417 0.551 .945 1.280 .031 36.0 14.0 24.0 32.5 .8

DMF685*250G 6.8 1.654 0.630 1.063 1.476 .039 42.0 16.0 27.0 37.5 1.0

DMF106*250G 10.0 1.654 0.748 1.378 1.476 .039 42.0 19.0 35.0 37.5 1.0

* Indicate capacitance tolerance: J = 앧5%, K = 앧10%, M = 앧20%

Catalog

Number

DMF103*063A .01 .413 .217 .354 .295 .024 10.5 5.5 9.0 7.5 .6

DMF153*063A .015 .413 .236 .374 .295 .024 10.5 6.0 9.5 7.5 .6

DMF223*063A .022 .413 .236 .374 .295 .024 10.5 6.0 9.5 7.5 .6

DMF333*063A .033 .413 .236 .374 .295 .024 10.5 6.0 9.5 7.5 .6

DMF473*063A .047 .413 .236 .374 .295 .024 10.5 6.0 9.5 7.5 .6

DMF683*063A .068 .413 .236 .374 .295 .024 10.5 6.0 9.5 7.5 .6

DMF104*063A .1 .413 .236 .374 .295 .024 10.5 6.0 9.5 7.5 .6

DMF154*063A .15 .413 .276 .413 .295 .024 10.5 7.0 10.5 7.5 .6

DMF224*063A .22 .413 .276 .413 .295 .024 10.5 7.0 10.5 7.5 .6

DMF334*063A .33 .413 .315 .433 .295 .024 10.5 8.0 11.0 7.5 .6

DMF474*063A .47 .413 .315 .453 .295 .024 10.5 8.0 11.5 7.5 .6

DMF684*063B .68 .512 .276 .453 .394 .024 13.0 7.0 11.5 10.0 .6

DMF105*063B 1.0 .512 .276 .492 .394 .024 13.0 7.0 12.5 10.0 .6

DMF155*063C 1.5 .728 .315 .551 .591 .031 18.5 8.0 14.0 15.0 .8

DMF225*063C 2.2 .728 .394 .591 .591 .031 18.5 10.0 15.0 15.0 .8

Note: Add "TA" to end of part number for Tape and Ammo

쐀

NEW

191

Mallory Products for CDE/6325 Digital Way/Indianapolis IN 46278/Phone: (317)275-2285/Fax: (317)275-2293/www.cornell-dubilier.com

Film CapacitorsFilm Capacitors

Film Capacitors

DMF Series

Metallized Polyester / Radial Leads

Catalog

Number Cap

애애

애FLTH 얒얒

얒얒

얒dSL

MillimetersInches

THS얒얒

얒얒

얒d

400 VDC/200 VAC

630 VDC/220 VAC

DMF103*630B .01 .512 .236 .394 .394 .024 13.0 6.0 10.0 10.0 .6

DMF153*630B .015 .512 .256 .413 .394 .024 13.0 6.5 10.5 10.0 .6

DMF223*630B .022 .512 .295 .492 .394 .024 13.0 7.5 12.5 10.0 .6

DMF333*630C .033 .728 .256 .472 .591 .024 18.5 6.5 12.0 15.0 .6

DMF473*630C .047 .728 .295 .492 .591 .024 18.5 7.5 12.5 15.0 .6

DMF683*630C .068 .728 .335 .551 .591 .031 18.5 8.5 14.0 15.0 .8

DMF104*630C .1 .728 .394 .571 .591 .031 18.5 10.0 14.5 15.0 .8

DMF154*630D .15 .886 .374 .650 .787 .031 22.5 9.5 16.5 20.0 .8

DMF224*630D .22 .886 .453 .748 .787 .031 22.5 11.5 19.0 20.0 .8

DMF334*630E .33 1.260 .472 .748 1.083 .031 32.0 12.0 19.0 27.5 .8

DMF474*630E .47 1.260 .531 .866 1.083 .031 32.0 13.5 22.0 27.5 .8

DMF684*630F .68 1.417 .571 .886 1.280 .031 36.0 14.5 22.5 32.5 .8

DMF105*630F 1.0 1.417 .630 1.142 1.280 .031 36.0 16.0 29.0 32.5 .8

DMF155*630G 1.5 1.654 .728 1.161 1.476 .039 42.0 18.5 29.5 37.5 1.0

DMF225*630H 2.2 1.811 .807 1.280 1.673 .039 46.0 20.5 32.5 42.5 1.0

* Indicate capacitance tolerance: J = 앧5%, K = 앧10%, M = 앧20%

DMF103*400A .01 .413 .217 .354 .295 .024 10.5 5.5 9.0 7.5 .6

DMF153*400A .015 .413 .236 .374 .295 .024 10.5 6.0 9.5 7.5 .6

DMF223*400B .022 .512 .236 .374 .394 .024 13.0 6.0 9.5 10.0 .6

DMF333*400B .033 .512 .256 .394 .394 .024 13.0 6.5 10.0 10.0 .6

DMF473*400B .047 .512 .276 .472 .394 .024 13.0 7.0 12.0 10.0 .6

DMF683*400B .068 .512 .315 .512 .394 .024 13.0 8.0 13.0 10.0 .6

DMF104*400C .1 .728 .276 .492 .591 .031 18.5 7.0 12.5 15.0 .8

DMF154*400C .15 .728 .315 .531 .591 .031 18.5 8.0 13.5 15.0 .8

DMF224*400D .22 .886 .315 .571 .787 .031 22.5 8.0 14.5 20.0 .8

DMF334*400D .33 .886 .354 .591 .787 .031 22.5 9.0 15.0 20.0 .8

DMF474*400D .47 .886 .453 .728 .787 .031 22.5 11.5 18.5 20.0 .8

DMF684*400E .68 1.260 .472 .748 1.083 .031 32.0 12.0 19.0 27.5 .8

DMF105*400E 1.0 1.260 .531 .846 1.083 .031 32.0 13.5 21.5 27.5 .8

DMF155*400F 1.5 1.417 .551 .925 1.280 .031 36.0 14.0 23.5 32.5 .8

DMF225*400F 2.2 1.417 .728 1.083 1.280 .031 36.0 18.5 27.5 32.5 .8

DMF335*400G 3.3 1.654 .728 1.201 1.476 .039 42.0 18.5 30.5 37.5 1.0

DMF475*400H 4.7 1.811 .866 1.339 1.673 .039 46.0 22.0 34.0 42.5 1.0

Note: Add "TA" to end of part number for Tape and Ammo

쐀

NEW

192Mallory Products for CDE/6325 Digital Way/Indianapolis IN 46278/Phone: (317)275-2285/Fax: (317)275-2293/www.cornell-dubilier.com

Film CapacitorsFilm Capacitors

Film Capacitors

DMF Series

Metalliz ed Polyester / Radial Leads

Item Code Millimeters Inches

Dimensions Component Quantity

Per Ammo Pack

Quantity

Ammo Pack

Case

Code

A 1000

B 800

C 300

D 200

Size

Code Millimeters

+0.8-0.2 Inches

+.031-.008

P Dimension

A 5.0 .197 12.7 .500

B 5.0 .197 15.0 .591

C 7.5 .295 25.4 1.0

D 7.5 .295 25.4 1.0

Lead-Wire Diameter 얒d 0.6앐.05 .024앧.002

Lead-to-Lead Distance P SEE CHART

Feed Hole Pitch p012.7앧0.3 .5앧.012

Pitch of Component p1 SEE CHART

Hole Center to Lead p23.85앧0.7 .152앧.028

Feed Hole Center to p36.35앧1.3 .250앧.051

Component Center

Component Alignment, F-R 욼h0

앧2.0 0앧.079

Tape Width W 18+1.0-0.5 .709+.039-.020

Hold-Down Tape Width W012.5 min .492 min

Hole Position W19.0+0.5 .354앐.020

Hold-Down Tape Position W23.0 Max .118 Max

Height of Component H 16.0앧0.5 .630앧.02

from Tape Center

Feed Hole Diameter D04.0앧0.2 .157앧.008

P3P1

P0PP2

얒d

욼h

340 mm Max

13.39"

55 mm Max

2.17"

360 mm Max

14.17"

Ammo Box

Packing

Millimeters

앧앧

앧1.0 Inches

앧앧

앧.040

p1 Dimension

*Taping not available for lead spacing greater than 20.0mm or .780in.

쐀

NEW