NX8560LJ509-BC - NEC Electronics - Datasheet.Directory

NEC's EA MODULATOR

INTEGRATED InGaAsP MQW DFB

LASER DIODE IN BUTTERFLY PACKAGE

WITH GPO CONNECTOR

FOR 10 Gb/s DWDM APPLICATIONS

NX8560LJ

SERIES

FEATURES

• INTEGRATED ELECTROABSORPTION MODULATOR

• UP TO 40 km TRANSMISSION CAPABILITY

WITH STAN DARD SINGLE MODE FIBER

(dispersion 800 ps/nm)

• LOW MODULATION VOLTAGE

• 7-PIN BUTTERFLY PACKAGE WITH GPO™ CONNECTOR

• AVAILABLE FOR DWDM WAVELENGTH

BASED ON ITU-T RECOMMENDATION

NEC's NX8560LJ Series are an Electro-Absorption (EA) Mod u -

la tor integrated, 1550 nm Multiple Quantum Well (MQW) struc-

tured Distributed Feed-Back (DFB) laser diodes. It is capable

of transmitting up to 40 km for 10 Gb/s applications by using

standard ﬁ ber dispersion 800 ps/nm and is available for Dense

Wavelength Mul ti plex ing (DWDM) wavelength based on ITU-T

rec om men da tions.

DESCRIPTION

Note:

1. NX8560LJ Series: TSET is a certain point between 20°C and 35°C.

NX8560LJXXX Series: TSET is set at a certain point between 20°C and 35°C for ITU-T grid wavelength

2. 40 km SMF under modulation, 9.95328 Gb/s, PRBS 223-1, VEA = VCENTER ± 1/2VMOD, IFLD = Iop, NEC test system

Vcenter : a certain point between -2.0 V and -0.5 V.

Vmod : a certain point 3 V or below.

Iop : a certain point between 50 mA and 80 mA.

3. Available for DWDM wavelength based on ITU-T recommendations (100 GHz grid).

Please refer to ordering information.

4. BER = 10-10.

PART NUMBER NX8560LJ Series

SYMBOLS PARAMETERS AND CONDITIONS UNITS MIN TYP MAX

TSET Laser Set Temperature 1°C 20 35

Iop Operating Current mA 50 60 80

VCENTER Modulation Center Voltage V -2.0 -0.5

VMOD Modulation Voltage V 2.0 3.0

VFLD Forward Voltage of LD, IFLD = Iop V 2.0

ITH Threshold Current, TLD = Tset mA 7 20

PfOptical Output from Fiber, Under modulation2dBm -3 -2

λpPeak Emission Wavelength, IFLD = Iop, VEA = 0 V nm 1528 ITU-T31563

SMSR Side Mode Suppression Ratio, IFLD = Iop, VEA = 0 V dB 30 >37

ER Extinction Ratio, Under modulation2dB 10 >11

trRise Time, 20-80%, Under modulation2ps 40

tfFall Time, 80-20%, Under modulation2ps 40

DP Dispersion Penalty, 40 km SMF under modulation2, 4 dB 2.0

ISOL Optical Isolation dB 23

S11 RF Return Loss,

IFLD = IOP, VEA = -1 V, f = 130 MHz to 5 GHz

IFLD = IOP, VEA = -1 V, f = 5 GHz to 10 GHz dB

dB -10

-8 -8

-5

ELECTRO-OPTICAL CHARACTERISTICS (TLD = Tset, TC = 25°C, BOL unless otherwise speciﬁ ed)

California Eastern Laboratories

PRELIMINARY DATA SHEET

ABSOLUTE MAXIMUM RATINGS1

(TC = 25°C, unless otherwise speciﬁ ed)

SYMBOLS PARAMETERS UNITS RATINGS

Pf Optical Output from Fiber mW 10

IFLD Forward Current of LD mA 150

VRLD Reverse Voltage of LD V 2.0

VFm Forward Voltage of Modulator V 1

VRm Reverse Voltage of Modulator V 4

IFPD Forward Current of PD mA 1

VRPD Reverse Voltage of PD V 10

IC Cooler Current A 1.5

VC Cooler Voltage V 2.5

TC Operating Case Temperature °C -20 to +70

TSTG Storage Temperature °C -40 to +85

TSLD Lead Soldering °C 350

Temperature (3 s)

Note:

1. Operation in excess of any one of these parameters may result

in permanent damage.

PART NUMBER NX8560LJ SERIES

SYMBOLS PARAMETERS AND CONDITIONS UNITS MIN TYP MAX

Im Monitor Current, VRPD = 5V, IFLD = IOP, VEA = 0 V µA 30 1100

ID Dark Current, VRPD = 5 V, VEA = 0 V nA 10

Ct Terminal Capacitance, VRPD = 5 V, f = 1 Mhz pF 15

γ1 Tracking Error, Im = const. dB 0.5

ELECTRO-OPTICAL CHARACTERISTICS (Applicable to Monitor PD: TLD = Tset, TC = -20 to +70°C)

(mW) TLD = TC = 25°C

(at Pf (25°C) = Pop)

TLD = 25°C, TC = -20 to +70°C

Pop

Note:

1. γ = 10 log Pf

Pop

PART NUMBER NX8560LJ SERIES

SYMBOLS PARAMETERS AND CONDITIONS UNITS MIN TYP MAX

R Thermistor Resistance, TLD = 25°C kΩ 9.5 10.0 10.5

B B Constant K 3350 3450 3550

IC Cooler Current, TLD = Tset A 1.2

VC Cooler Voltage, TLD = Tset V 2.4

ELECTRO-OPTICAL CHARACTERISTICS (Applicable to Thermistor and TEC: TC = -20 to +70°C)

NX8560LJ SERIES

TYPICAL PERFORMANCE CURVES (TC = 25°C unless otherwise speciﬁ ed)

OPTICAL OUTPUT POWER FROM FIBER

vs. FORWARD CURRENT

Reverse Voltage of Modulator, VREA (V)

TExtinction Ratio, ER (dB)

EXTICTION RATIO vs.

MODULAR VOLTAGE

Optical Output Power from Fiber, Pf (mW)

Forward Current, IF (mA)

INPUT RETURN LOSS

CHARACTERISTICS (S11)

Case Temperature, Tc (°C)

Input Return Loss, S11 (dB)

ERROR RATE

CHARACTERISTICS

Bit Error Rate

Monitor Current, Im (mA)

VREA = 0 V

0.5 V

1 V

2 V

3 V

050 100 150 200

0123

-5

-10

-15

-20

-25

051015 20

9.95328 Gb/s

PRBS 223 -1,

Tx: NX8560LJ,

Rx: NR3470MU

back to back

after 800 ps/nm

10-4

10-5

10-6

10-7

10-8

10-9

10-10

10-11

10-12

–22 –20 –18 –16 –14 –12

Frequency, f (GHz) Average Recieved Power, P (dBm)

Remark:

1. The graphs indicate nominal characteristics.

NX8560LJ SERIES

Wavelength Code ITU-T Wavelength1

(nm) Frequency

(THz) Wavelength Code ITU-T Wavelength1

(nm) Frequency

(THz)

287 1528.77 196.10 501 1550.11 193.40

295 1529.55 196.00 509 1550.91 193.90

303 1530.33 195.90 517 1551.72 193.20

311 1531.11 195.80 525 1552.52 193.10

318 1531.89 195.70 533 1553.32 193.00

326 1532.68 195.60 541 1554.13 192.90

334 1533.46 195.50 549 1554.94 192.80

342 1534.25 195.40 557 1555.74 192.70

350 1535.03 195.30 565 1556.55 192.60

358 1535.82 195.20 573 1557.36 192.50

366 1536.60 195.10 581 1558.17 192.40

373 1537.39 195.00 589 1558.98 192.30

381 1538.18 194.90 597 1559.79 192.20

389 1538.97 194.80 606 160.60 192.10

397 1539.76 194.70 614 1561.41 192.00

405 1540.55 194.60 622 4562.23 191.90

413 1541.36 194.50 630 1563.04 191.80

421 1542.14 194.40

429 1542.91 194.30

437 1543.73 194.20

445 1544.52 194.10

453 1545.32 194.00

461 1546.11 193.90

469 1546.91 193.90

477 1547.71 193.70

485 1548.51 193.60

493 1549.31 193.50

ORDERING INFORMATION

NX8560LJ -

CC : SC-UPC connector (standard)

BC : FC-UPC connector (option)

Without wavelength code: Wavelength is a certain point between

1528.77 to 1563.04 nm

With Wavelength code : Refer to Table A

Table A: DWDM wavelength base on ITU-T recommendations (@ TLD = Tset)

Note:

1. The value which omitted and computed the 3rd place below the decimal point

Life Support Applications

These NEC products are not intended for use in life support devices, appliances, or systems where the malfunction of these products can reasonably be expected

to result in personal injury. The customers of CEL using or selling these products for use in such applications do so at their own risk and agree to fully indemnify

CEL for all damages resulting from such improper use or sale.

OUTLINE DIMENSIONS (Units in mm, unless otherwise speciﬁ ed ±0.2 mm tolerance)

PARAMETER UNITS SPECIFICATIONS

Mode Field Diameter µm 9.3±0.5

Cladding Diameter µm 125±1

Tight Buffer Diameter µm 900±100

Cut-off Wavelength nm <1270

Attenuation 1525 to 1575 dB/km <0.3

Minimum Fiber Bending Radius mm 30

Fiber Length mm 1000 MIN

Flammability UL1581 VW-1

OPTICAL FIBER CHARACTERISTICS

8.99±0.5 mm

35±2 mm

Fiber Length: 1000 mm MIN.

-BC : FC-UPC Connector

-CC : SC-UPC Connector

Optical Fiber (SMF)

Length : 1000 MIN

30.0

0.75

20.83±0.13

26.04±0.13

15.24

2.54

22.0 MAX

4 - φ2.67

1.25

0.9

10 MIN

8.89±0.13 12.7±0.15

6.0

8.0

#7 #1

Cooler

5.4

5.08

Thermistor

MOD

7.8 4.83

05/16/2003

NX8560LJ SERIES

PIN No. FUNCTION

1 THERMISTOR

2 THERMISTOR

3 LD DC Bias

4 PD ANODE

5 PD CATHODE,

6 COOLER ANODE

7 COOLER CATHODE

PIN CONNECTIONS

TOP VIEW