Type 269 (No.P-269-E001) Type 269 is built-in fuse chip tantalum capacitors based on Type 267. FEATURES 1. With built-in fuse that blows out to prevent smoking and ignition of capacitor when overcurrent flows. 2. Suitable for surface mounting. 3. Dimensional accuracy and symmetrical terminal structure suitable for high-density mounting ensures excellent "Self-Alignment". 4. Soldering : 260C for 10 seconds by reflow or flow soldering. 5. Suitable for filtering of power supply with low impedance circuit. RATING Item Rating Category temperature range (Operating temperature ) -55 ~ +125C Rated Temperature (Maximum operating temperature for DC rated Voltage) +85C (1) DC rated voltage rangeUR See CATALOG NUMBERS AND Rated capacitance (Normal capacitance rangeCR) RATING OF STANDARD PRODUCTS Rated capacitance tolerance and EXTENDED PRODUCTS. Failure rate level 1%/1000 h (1) Note : For operation 125,derate voltage linearly to 67% of 85 voltage rating. ORDERING INFORMATION 269 E 1602 226 M R 720 TYPE SERIES RATED VOLTAGE CAPACITANCE CAPACITANCE TOLERANCE STYLE OF REELED PACKAGE SPECIAL CODE Taping specification Marking Series Marking M E Standard Extended 6301 1002 1602 2002 2502 3502 5002 Rated voltage 6.3VDC 10VDC 16VDC 20VDC 25VDC 35VDC 50VDC Marking Capacitance Marking Capacitance Marking Capacitance 0.15 m 0.22 m 0.33 m 0.47 m 0.68 m 1.0 m 154 224 334 474 684 105 1.5 m 2.2 m 3.3 m 4.7 m 6.8 m 10 m 155 225 335 475 685 106 156 226 336 476 686 107 157 Marking 15 m 22 m 33 m 47 m 68 m 100 m 150 m K M DIMENSIONS [ Case] P1 P2 P1 [D3 Case] [C3, Case] mm Case Code B C3 D3 E EIA Code L0.2 W0.2 T0.2 P10.2 P2 min. C0.1 3528 6032 7343 7257 3.5 6.0 7.3 7.3 2.8 3.2 4.4 5.8 1.9 2.5 2.8 3.5 0.8 1.3 1.3 1.3 1.5 3.0 4.0 4.0 2.2 2.2 2.4 3.5 1 Capacitance Tolerance 10% 20% Code Reel Size Anode Notation R L N P 180 Reel 180 Reel 330 Reel 330 Reel Feed hole: + Feed hole: Feed hole: + Feed hole: - RECOMMENDED SOLDER PAD LAYOUT mm a B C3 D3 E Flow Reflow 3.2 4.2 5.2 5.6 2.0 2.4 2.4 2.4 b c 2.4 2.5 2.7 3.8 1.8 3.3 4.6 4.6 b Case Code c a In order to expect the self alignment effect, it is recommended that land width is almost the same size as terminal of capacitor,and space between lands (c) nearly equal to the space between terminals for appropriate soldering. MARKING [ B case ] [C3, D3, E case ] Capacitance tolerance (+/-10% notation) 474 35 A Rated capacitance (1) 106K 16 A Rated capacitance (1) Date code (2) Capacitance tolerance (K:+/-10%) Date code (2) Rated voltage Rated voltage Polarity (Anode notion) Polarity (Anode notion) (1) Note : First two digits are significant figures of capacitance value(pF). Third digit is the number of zeros following. Note(2): Date codes are based on the Annex 1 Table 13 of JIS C 5101-1. STANDARD RATING Series M : Standard products R.V.(VDC) Cap.( mF ) 0.15 0.22 0.33 0.47 0.68 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 6.3 10 16 B B B C3 C3 D3 D3 C3 C3 D3 D3 E E 20 25 B B B B C3 C3 D3 D3 E E C3 C3 D3 D3 E E 35 B , C3 C3 C3 C3 , D3 D3 D3 , E E E 50 B B B C3 C3 C3 D3 D3 E E Series E : Extended products R.V.(VDC) Cap.( mF ) 0.47 0.68 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 150 6.3 10 16 20 25 35 50 B C3 B D3 B B C3 D3 B , D3 D3 B B C3 B , D3 D3 D3 , E B B C3 D3 D3 E C3 C3 D3 C3 2 3 2 269M 6301 107 _ _ 720 1 2 269M 1002 475 _ _ 1 2 269M 1002 106 _ _ 720 1 2 269M 1002 156 _ _ 720 1 2 269M 1002 226 _ _ 720 1 2 269M 1002 336 _ _ 720 1 2 269M 1002 686 _ _ 720 1 2 269M 1602 225 _ _ 1 2 269M 1602 335 _ _ 1 2 269M 1602 685 _ _ 720 1 2 269M 1602 106 _ _ 720 1 2 269M 1602 156 _ _ 720 1 2 269M 1602 226 _ _ 720 1 2 269M 1602 336 _ _ 720 1 2 269M 1602 476 _ _ 720 1 2 269M 2002 155 _ _ 1 2 269M 2002 225 _ _ 1 2 269M 2002 475 _ _ 720 1 2 269M 2002 685 _ _ 720 1 2 269M 2002 106 _ _ 720 1 2 269M 2002 156 _ _ 720 1 2 269M 2002 226 _ _ 720 1 2 269M 2002 336 _ _ 720 1 2 269M 2502 105 _ _ 1 2 269M 2502 155 _ _ 1 2 269M 2502 335 _ _ 720 1 2 269M 2502 475 _ _ 720 1 2 269M 2502 685 _ _ 720 1 2 269M 2502 106 _ _ 720 1 2 269M 2502 156 _ _ 720 1 2 269M 2502 226 _ _ 720 1 2 269M 3502 105 _ _ 1 2 269M 3502 105 _ _ 720 1 2 269M 3502 155 _ _ 720 1 Catalog Number 6.3 10 16 20 25 35 UR VDC 8 13 20 26 32 44 85 5 8 13 16 20 28 125 US VDC 100 4.7 10 15 22 33 68 2.2 3.3 6.8 10 15 22 33 47 1.5 2.2 4.7 6.8 10 15 22 33 1.0 1.5 3.3 4.7 6.8 10 15 22 1.0 1.0 1.5 CR F E B C3 C3 D3 D3 E B B C3 C3 D3 D3 E E B B C3 C3 D3 D3 E E B B C3 C3 D3 D3 E E B C3 C3 Case code 6.3 0.5 1.0 1.5 2.2 3.3 6.7 0.5 0.5 1.1 1.6 2.4 3.5 5.3 7.5 0.5 0.5 0.9 1.4 2.0 3.0 4.4 6.6 0.5 0.5 0.8 1.2 1.7 2.5 3.8 5.5 0.5 0.5 0.5 20 63 5 10 15 22 33 67 5 5 11 16 24 35 53 75 5 5 9 14 20 30 44 66 5 5 8 12 17 25 38 55 5 5 5 85 79 6.3 13 19 28 41 85 6.3 6.3 14 20 30 44 66 94 6.3 6.3 12 17 25 38 55 83 6.3 6.3 9.6 15 21 31 47 69 6.3 6.3 6.3 125 Leakage current (DCL) A +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 -55 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 85 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 125 Variation rate of cap. C/C% CATALOG NUMBERS AND RATING OF STANDARD PRODUCTS -55 0.10 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.05 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.05 0.05 0.08 0.08 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.04 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.04 0.04 0.06 20 0.08 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.04 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.04 0.04 0.06 85 Dissipation factor 0.08 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.08 0.06 0.06 0.05 0.06 0.06 0.06 0.06 0.08 0.06 0.06 0.05 0.05 0.06 125 February, 2011 0.7 3.0 1.2 1.2 1.0 1.0 0.7 3.0 3.0 1.2 1.2 1.0 1.0 0.7 0.7 3.0 3.0 1.2 1.2 1.0 1.5 0.7 1.0 3.0 3.0 1.2 1.2 1.0 1.5 0.7 1.0 3.0 3.0 1.2 10kHz ESR +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 C/C% A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A *DCL +/-3 +/-3 +/-3 +/-3 +/-3 +/-3 +/-3 +/-3 +/-3 +/-3 +/-3 +/-3 +/-3 +/-3 +/-3 +/-3 +/-3 +/-3 +/-3 +/-3 +/-3 +/-3 +/-3 +/-3 +/-3 +/-3 +/-3 +/-3 +/-3 +/-3 +/-3 +/-3 +/-3 +/-3 C/C% +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 C/C% Rapid Surge Resistance to soldering heat change of temp. A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A A *DCL +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 C/C% Damp heat B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B B *DCL +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 C/C% Endurance 4 2 35 50 44 63 85 28 40 125 US VDC 2.2 3.3 3.3 4.7 6.8 6.8 10 15 0.15 0.22 0.33 0.47 0.68 1.0 1.5 2.2 CR F C3 C3 D3 D3 D3 E E E B B B C3 C3 C3 D3 D3 20 Case code 0.8 1.2 1.2 1.6 2.4 2.4 3.5 5.3 0.5 0.5 0.5 0.5 0.5 0.5 0.8 1.1 20 8 12 12 16 24 24 35 55 5 5 5 5 5 5 8 11 85 9.6 14 14 21 30 30 44 66 6.3 6.3 6.3 6.3 6.3 6.3 9.4 14 125 Leakage current (DCL) A +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 -55 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 85 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 125 Variation rate of cap. C/C% 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.05 0.05 0.05 0.05 0.05 0.05 0.08 0.08 -55 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.04 0.04 0.04 0.04 0.04 0.04 0.06 0.06 20 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.04 0.04 0.04 0.04 0.04 0.04 0.06 0.06 85 Dissipation factor 0.06 0.06 0.06 0.06 0.08 0.06 0.06 0.06 0.05 0.05 0.05 0.05 0.05 0.05 0.06 0.06 125 1.2 1.2 1.0 1.0 1.5 0.7 0.7 1.0 5.0 5.0 3.0 3.0 3.0 3.0 1.5 1.5 10kHz ESR +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 C/C% A A A A A A A A A A A A A A A A *DCL +/-3 +/-3 +/-3 +/-3 +/-3 +/-3 +/-3 +/-3 +/-3 +/-3 +/-3 +/-3 +/-3 +/-3 +/-3 +/-3 C/C% +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 C/C% Rapid Surge Resistance to soldering heat change of temp. A A A A A A A A A A A A A A A A *DCL +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 C/C% Damp heat *UR = Rated Voltage US = Surge Voltage CR = Capacitance Note1 : For Capacitance Tolerance , insert "K" or "M" into _1 Note2 : For Reeled Package, insert "R" , "L" , "N" or "P" into _2 Note3 : The letter "A" at the end of catalog number = Moisture-proof packaging. Note5 : *DCL code:A=Shall not exceed the value of initial specification., B=Shall not exceed 1.25 times the value of initial specification.,C=Shall not exceed 2 times the value of initial specification 269M 3502 225 _ _ 720 1 2 269M 3502 335 _ _ 734 1 2 269M 3502 335 _ _ 720 1 2 269M 3502 475 _ _ 720 1 2 269M 3502 685 _ _ 734 1 2 269M 3502 685 _ _ 720 1 2 269M 3502 106 _ _ 720 1 2 269M 3502 156 _ _ 720 1 2 269M 5002 154 _ _ 1 2 269M 5002 224 _ _ 1 2 269M 5002 334 _ _ 1 2 269M 5002 474 _ _ 720 1 2 269M 5002 684 _ _ 720 1 2 269M 5002 105 _ _ 720 1 2 269M 5002 155 _ _ 720 1 2 269M 5002 225 _ _ 720 1 Catalog Number UR VDC B B B B B B B B B B B B B B B B *DCL +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 C/C% Endurance 5 2 6.3 10 16 20 35 50 8 13 20 26 44 63 85 5 8 13 16 28 40 125 US VDC 10 47 68 100 100 150 6.8 10 33 47 47 68 100 100 4.7 10 15 22 33 47 68 3.3 10 15 22 15 0.47 1.5 3.3 CR F B C3 D3 B D3 D3 B B C3 B D3 D3 D3 E B B B C3 D3 D3 E B C3 C3 D3 C3 B C3 D3 Case code 0.6 3.0 4.3 6.3 6.3 9.5 0.7 1.0 3.3 4.7 4.7 6.8 10 10 0.8 1.6 2.4 3.5 5.3 7.5 11 0.7 2.0 3.0 4.4 3.8 0.5 0.8 1.7 20 6 30 43 63 63 95 7 10 33 47 47 68 100 100 8 16 24 35 53 75 109 7 20 30 44 38 5 8 17 85 7.9 37 54 79 79 118 8.5 13 41 59 59 85 130 125 9.4 20 30 44 66 94 136 8.3 25 38 55 47 6.3 9.4 21 125 Leakage current (DCL) A +/-10 +/-10 +/-10 +/-20 +/-10 +/-10 +/-10 +/-10 +/-10 +/-20 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 -55 +/-10 +/-10 +/-10 +/-20 +/-10 +/-10 +/-10 +/-10 +/-10 +/-20 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 85 +/-15 +/-15 +/-15 +/-20 +/-15 +/-15 +/-15 +/-15 +/-15 +/-20 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 +/-15 125 Variation rate of cap. C/C% -55 0.08 0.08 0.08 0.22 0.15 0.15 0.08 0.08 0.08 0.18 0.08 0.08 0.15 0.10 0.08 0.08 0.12 0.08 0.08 0.08 0.10 0.08 0.08 0.08 0.08 0.10 0.06 0.08 0.08 0.06 0.06 0.06 0.15 0.08 0.08 0.06 0.06 0.06 0.12 0.06 0.06 0.08 0.08 0.06 0.06 0.08 0.06 0.06 0.06 0.08 0.06 0.06 0.06 0.06 0.08 0.04 0.06 0.06 20 0.06 0.06 0.06 0.15 0.08 0.08 0.06 0.06 0.06 0.12 0.06 0.06 0.08 0.08 0.06 0.06 0.08 0.06 0.06 0.06 0.08 0.06 0.06 0.06 0.06 0.08 0.04 0.06 0.06 85 Dissipation factor 0.08 0.08 0.08 0.18 0.10 0.10 0.08 0.08 0.08 0.14 0.08 0.08 0.10 0.08 0.08 0.08 0.10 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.10 0.06 0.08 0.08 125 February, 2011 3.0 1.2 1.0 3.0 1.0 1.0 3.0 3.0 1.2 3.0 1.0 1.0 1.0 0.7 3.0 3.0 3.0 1.2 1.0 1.0 0.7 3.0 1.2 1.2 1.0 1.4 3.0 1.2 1.0 10kHz ESR +/-5 +/-5 +/-5 +/-20 +/-5 +/-5 +/-5 +/-5 +/-5 +/-20 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 C/C% A A A C A A A A A A A A A A A A A A A A A A A A A A A A A *DCL C/C% +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-10 +/-20 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-10 +/-20 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 C/C% Rapid Surge Resistance to soldering heat change of temp. A A A C A A A A A C A A A A A A A A A A A A A A A A A A A *DCL +/-5 +/-5 +/-5 +/-10 +/-5 +/-5 +/-5 +/-5 +/-5 +/-10 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 +/-5 C/C% Damp heat *UR = Rated Voltage US = Surge Voltage CR = Capacitance Note1 : For Capacitance Tolerance , insert "K" or "M" into _1 Note2 : For Reeled Package, insert "R" , "L" , "N" or "P" into _2 Note3 : The letter "A" at the end of catalog number = Moisture-proof packaging. Note5 : *DCL code:A=Shall not exceed the value of initial specification., B=Shall not exceed 1.25 times the value of initial specification.,C=Shall not exceed 2 times the value of initial specification 269E 6301 106 _ _ 1 2 269E 6301 476 _ _ 720 1 2 269E 6301 686 _ _ 720 2 269E 6301 107 M _ 1 2 269E 6301 107 _ _ 720 A 1 2 269E 6301 157 _ _ 734 A 1 2 269E 1002 685 _ _ 1 2 269E 1002 106 _ _ 1 2 269E 1002 336 _ _ 720 1 2 269E 1002 476 _ _ 1 2 269E 1002 476 _ _ 720 1 2 269E 1002 686 _ _ 720 A 1 2 269E 1002 107 _ _ 734 A 2 269E 1002 107 M _ 720 1 2 269E 1602 475 _ _ 1 2 269E 1602 106 _ _ 1 2 269E 1602 156 _ _ 1 2 269E 1602 226 _ _ 720 1 2 269E 1602 336 _ _ 720 1 2 269E 1602 476 _ _ 720 A 1 2 269E 1602 686 _ _ 720 1 2 269E 2002 335 _ _ 1 2 269E 2002 106 _ _ 720 1 2 269E 2002 156 _ _ 720 1 2 269E 2002 226 _ _ 720 1 2 269E 2502 156 _ _ 734 1 2 269E 5002 474 _ _ 1 2 269E 5002 155 _ _ 720 1 2 269E 5002 335 _ _ 720 1 Catalog Number UR VDC CATALOG NUMBERS AND RATING OF EXTENDED PRODUCTS B B B C B B B B B C B B B B B B B B B B B B B B B B B B B *DCL +/-10 +/-10 +/-10 +/-20 +/-10 +/-10 +/-10 +/-10 +/-10 +/-20 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 +/-10 C/C% Endurance PERFORMANCE No. Item Leakage Current (A) Performance Shall not exceed 0.01 CV or 0.5 whichever is greater. Capacitance (F) Shall be within tolerance of the nominal value specified. Dissipation Factor Shall not exceed the values shown in CATALOG NUMBERS AND RATING OF STANDARD PRODUCTS or EXTENDED PRODUCTS. ESR (Equivalent series resistance) Shall not exceed the values shown in CATALOG NUMBERS AND RATING OF STANDARD PRODUCTS or EXTENDED PRODUCTS. 1 2 3 4 Characteristics at High and LowTemperature Leakage Step Current Capacitance 1 Dissipation Factor Capacitance Change Step 2 Dissipation Factor Step 3 Leakage Current Capacitance Change Dissipation Factor Leakage Current 5 Step 4 Capacitance Change Dissipation Factor Leakage Current Step 5 Capacitance Change Dissipation Factor Step 6 Surge 6 Leakage Current Capacitance Change Dissipation Factor Leakage Current Capacitance Change Dissipation Factor Appearance Shear Test JIS C 5101-1, 4.29 Shall not exceed the value in No.1. Shall be within the specified tolerance. Shall not exceed the values shown in CATALOG NUMBERS AND RATING OF STANDARD PRODUCTS or EXTENDED PRODUCTS. Shall not exceed the value shown in CATALOG NUMBERS AND RATING OF STANDARD PRODUCTS or EXTENDED PRODUCTS. Shall not exceed the values shown in CATALOG NUMBERS AND RATING OF STANDARD PRODUCTS or EXTENDED PRODUCTS. Shall not exceed the value in No.1. Shall be within 2% of the value at Step 1. Shall not exceed the values shown in CATALOG NUMBERS AND RATING OF STANDARD PRODUCTS or EXTENDED PRODUCTS. Shall not exceed the value shown in CATALOG NUMBERS AND RATING OF STANDARD PRODUCTS or EXTENDED PRODUCTS. Shall not exceed the value shown in CATALOG NUMBERS AND RATING OF STANDARD PRODUCTS or EXTENDED PRODUCTS. Shall not exceed the values shown in CATALOG NUMBERS AND RATING OF STANDARD PRODUCTS or EXTENDED PRODUCTS. Shall not exceed the value shown in CATALOG NUMBERS AND RATING OF STANDARD PRODUCTS or EXTENDED PRODUCTS. Shall not exceed the value shown in CATALOG NUMBERS AND RATING OF STANDARD PRODUCTS or EXTENDED PRODUCTS. Shall not exceed the values shown in CATALOG NUMBERS AND RATING OF STANDARD PRODUCTS or EXTENDED PRODUCTS. Shall not exceed the value in No.1. Shall be within 2% of the value at Step 1. Shall not exceed the values shown in CATALOG NUMBERS AND RATING OF STANDARD PRODUCTS or EXTENDED PRODUCTS. Shall not exceed the value in No.1. Shall not exceed the value shown in CATALOG NUMBERS AND RATING OF STANDARD PRODUCTS or EXTENDED PRODUCTS. Shall not exceed the value in No.3. There shall be no evidence of mechanical damage. No exfoliation between lead terminal and board. 7 8 Test method JIS C 5101-1, 4.9 Applied Voltage : Rated Voltage for 5 min. Temperature : 20C JIS C 5101-1, 4.7 Frequency : 120 Hz 20% Voltage : 0.5Vrms+1.5 ~2VDC Temperature : 20C JIS C 5101-1, 4.8 Frequency : 120 Hz 20% Voltage : 0.5Vrms+1.5 ~2VDC Temperature : 20C Frequency : 10 kHz Temperature : 20C Substrate Bending Test Capacitance Appearance Initial value to remain steady during measurement. There shall be no evidence of mechanical damage. Vibration Capacitance Appearance Initial value to remain steady during measurement. There shall be no evidence of mechanical damage. 9 6 Measuring temperature : 20 2C Measuring temperature : -553 C Measuring temperature : 20 2C Measuring temperature : 852C Measuring temperature : 1252C Measuring voltage : Derated voltage at 125C Measuring temperature : 20 2C JIS C 5101-1, 4.26 Test temperature and applied voltage : To each half of specimens * 85 2C, * 125 2C Applied Voltage :DC surge voltage Series protective resistance : 1000 Discharge resistance : 1000 JIS C 5101-1, 4.34 Capacitors mounted under conditions JIS C 5101-1, 4.33 are used as specimens. Pressure : 5N Duration : 10 1 s JIS C 5101-1, 4.35 Bending : 3 mm Duration:5s JIS C 5101-1, 4.17 Frequency range : 10 ~ 55 Hz Swing width : 1.5 mm Vibration direction : 3 directions with mutually right-angled Duration : 2 hours in each of these mutually perpendicular directions (total 6 hours) Mounting : Solder terminal to the printed board Item Shock Performance There shall be no intermittent contact of 0.5 ms or greater, short, or open. Nor shall there be any spark discharge, insulation breakdown, or evidence of mechanical damage. Solderability Shall be covered to over 3/4 of terminal surface by new soldering. No. 10 11 12 13 14 Resistance to Soldering Heat Component solvent resistance Solvent resistance of marking Rapid Change of Temperature 15 Damp heat, Steady state Leakage Current Capacitance Change Dissipation Factor Appearance Leakage Current Capacitance Change Dissipation Factor Visual examination Leakage Current Capacitance Change Dissipation Factor Appearance Leakage Current Capacitance Change 16 Endurance Dissipation Factor Appearance Leakage Current Capacitance Change 17 Dissipation Factor Appearance 18 Fusing characteristics 19 Rushed current test Shall not exceed the value shown in CATALOG NUMBERS AND RATING OF STANDARD PRODUCTS or EXTENDED PRODUCTS. Shall not exceed the value shown in CATALOG NUMBERS AND RATING OF STANDARD PRODUCTS or EXTENDED PRODUCTS. Shall not exceed the value in No.3. There shall be no evidence of mechanical damage. Shall not exceed the value in No.1. Shall be within 3% of initial value. Shall not exceed the value in No.3. After the test the marking shall be legible. Shall not exceed the value in No.1. Shall not exceed the value shown in CATALOG NUMBERS AND RATING OF STANDARD PRODUCTS or EXTENDED PRODUCTS. Shall not exceed the value in No.3. There shall be no evidence of mechanical damage. Shall not exceed the value shown in CATALOG NUMBERS AND RATING OF STANDARD PRODUCTS or EXTENDED PRODUCTS. Shall not exceed the value shown in CATALOG NUMBERS AND RATING OF STANDARD PRODUCTS or EXTENDED PRODUCTS. Shall not exceed the value in No.3. There shall be no evidence of mechanical damage. Shall not exceed the value shown in CATALOG NUMBERS AND RATING OF STANDARD PRODUCTS or EXTENDED PRODUCTS. Shall not exceed the value shown in CATALOG NUMBERS AND RATING OF STANDARD PRODUCTS or EXTENDED PRODUCTS. Shall not exceed the value in No.3. Test method JIS C 5101-1, 4.19 Peak acceleration : 490 m/s2 Duration : 11 ms Wave form : Half-sine JIS C 5101-1, 4.15 Solder temperature : 230 5C Dipping time : 3 to 5 s Dipping depth : Terminal shall be dipped into melted solder. JIS C 5101-1, 4.14 One of the following methods (a) Complete dipping method Solder temperature: 260 5C Dipping time: 10 1 s (b) Terminal dipping method Solder temperature: 260 5C Dipping time: 10 1 s JIS C 5101-1, 4.31 Temperature : 23 5C Dipping time : 5 0.5 min. Conditioning : JIS C 0052 method 2 Solvent : 2-propanol (Isopropyl alcohol) JIS C 5101-1, 4.32 Temperature : 23 5C Dipping time : 5 0.5 min. Conditioning : JIS C 0052 method 1 Solvent : 2-propanol (Isopropyl alcohol) Rubbing material : cotton wool JIS C 5101-1, 4.16 Step 1 : -55 3C, 30 3 min. Step 2 : 25 +10 -5 C, 3 min. max. Step 3 : 125 2C, 30 3 min. +10 Step 4 : 25 -5 C, 3 min. max. Number of cycles : 5 JIS C 5101-1, 4.22 Temperature : 40 2C Moisture : 90 ~ 95%RH Duration : 500 +24 h 0 JIS C 5101-1, 4.23 Test temperature and applied voltage : 85 2C and rated voltage or 125 3C and 2/3 x rated voltage Duration : 2000 +72 h 0 Power supply impedance : 3 or less There shall be no evidence of mechanical damage. Please refer to FUSING CHARACTERISTICS (Reference). The fuse shall not blow out. 7 Applied voltage: Rated voltage Power supply capacity: Apply more than 20 A current FREQUENCY CHARACTERISTICS 269 16VDC-10mF C3-Case, Sample : 5pcs Measuring temperature : room temperature 10K Impedance & ESR () 1K 100 Impedance ( ) 10 1 0.1 ESR () 0.01 0.001 100 10K 1K 100K 10M 1M Frequency [Hz] TEMPERATURE CHARACTERISTICS 269 16VDC-10mF C3-Case, Sample : 12pcs 12 mean 10 100.00 6 4 2 10.00 0 -2 -4 -6 -8 -60 -40 -20 0 20 40 60 80 100 120 Temperature() Dissipation factor 0.10 Leakage Current Capacitance Change 8 1.00 0.10 0.08 0.06 0.04 0.02 0.00 0.01 -60 -40 -20 0 20 40 60 Temperature() 80 100 120 0 20 40 60 80 100 120 Temperature() 8 Dissipation factor Capacitance hange (%) DAMP HEAT, STEADY STATE 40, 95%RH 269 16VDC-10mF C3-Case, Sample : 50pcs 2 1 0 -1 -2 -3 -4 -5 Max. mean Min. 0.05 0.04 0.03 0.02 0.01 0 Leakage current (A) 1000 100 10 1 0.1 0.01 1 Dissipation factor Capacitance hange (%) ENDURANCE INITIAL VALUE DIP260 10 10secc 100 1000 10000 85, RATED VOLTAGE 269 16VDC-10mF C3-Case, Sample : 50pcs 2 1 0 -1 -2 -3 -4 -5 0.05 0.04 0.03 0.02 0.01 0 Leakage current (A) 1000 100 10 1 0.1 0.01 1 INITIAL VALUE DIP260 10 10sec 100 9 1000 10000 Max. mean Min. FUSING CHARACTERISTICS 100 Surface temperature peak 0.1 1 Fusing time 0.01 0 10 2 4 5 6 500 100 100 Surface temperature peak 10 1 1 Fusing time 0.1 10 0 2 100 Surface temperature peak 1 10 1 Fusing time 2 4 5 6 Fusing time (sec) 100 0 5 6 10 E case10V 68mF 500 Surface temperature peak() Fusing time (sec) D3 case16V 22mF 500 0.1 4 Applied current (A) Applied current (A) 10 10 500 500 100 100 Surface temperature peak 10 1 1 Fusing time 0.1 0 10 2 4 5 6 Applied current (A) Applied current (A) 10 10 10 Surface temperature peak() 1 500 Surface temperature peak() 10 Fusing time (sec) C3 case16V 10mF 500 Surface temperature peak() Fusing time (sec) B case16V 3.3mF 50 Application Notes for Tantalum Solid Electrolytic Capacitor 1. Operating Voltage Tantalum Solid Electrolytic Capacitor shall be operated at the rated voltage or lower. Rated voltage: The "rated voltage" refers to the maximum DC voltage that is allowed to be continuously applied between the capacitor terminals at the rated temperature. Surge voltage: The "surge voltage" refers to the voltage that is allowed to be instantaneously applied to the capacitor at the rated temperature or the maximum working temperature. The capacitor shall withstand the voltage when a 30-second cycle of application of the voltage through a 1000 series resistance is repeated 1000 times in 6-minute periods. When designing the circuit, the equipment's required reliability must be considered and appropriate voltage derating must be performed. 2. Application that contain AC Voltage Special attention to the following 3 items. (1) The sum of the DC bias voltage and the positive peak value of the AC voltage should not exceed the rated voltage. (2) Reverse voltage should not exceed the allowable values of the negative peak AC voltage. (3) Ripple current should not exceed the allowable values. 3. Reverse Voltage Tantalum solid electrolytic capacitor is polarity. Please do not impress reverse voltage. As well, please confirm the potential of the tester beforehand when both ends of the capacitor are checked with the tester etc. 4. Permissible Ripple Current The permissible ripple current and voltage at about 100 kHz or higher can be determined by the following formula from the permissible power loss (Pmax value)shown in Table 1 and the specified ESR value. However, when the expected operating temperature is higher than room temperature, determine the permissible values multiplying the Pmax value by the specified multiplier (Table 2). For the permissible values at different frequencies, consult our Sales Department. 2 P=I xESR or E 2 ESR P= Z2 Permissible ripple current P max ESR Imax= Permissible ripple voltage Emax= (Arms) P max ESR xZ = Imaxx Z (Vrms) Imax : Permissible ripple current at regulated frequency (Arms : RMS value) Emax : Permissible ripple voltage at regulated frequency (Vrms : RMS value) Pmax : Permissible power loss (W) ESR : Specified ESR value at regulated frequency () Z : Impedance at regulated frequency () Table 1 Permissible power loss Case size B C3 D3 E Table 2 Pmax multiplier at each operating temperature PmaxW 0.050 0.065 0.085 0.105 Operating temperature () 25 55 85 125 Multiplier 1.0 0.9 0.8 0.4 Note: Above values are measured at 0.8t glass epoxy board mounting in free air and may be changed depending on the kind of board, packing density, and air convection condition. Please consult us if calculated power loss value is different from above list of P max value. 5. Application on low-impedance circuit The failure rate of low impedance circuit at 0.1/V is about five times greater than that of a 1/V circuit. To curtail this higher failure rate, tantalum capacitors used in low impedance circuits, such as filters for power supplies, particularly switching power supplies, or for noise by-passing, require that operating voltage be derated to less than half of the rated voltage. Actually, less than 1/3 of the rated voltage is recommended. 6. Non Polar Application(BACK TO BACK) Tantalum capacitors can be used as a non-polar unit if two capacitors are connected "BACK-TO-BACK" when reserve voltage is applied at a more than permissible value, or in a purely AC circuit. The two capacitors should both be of the same rated voltage and capacitance tolerance, and they should both be twice the required capacitance value. + + Ripple Voltage: Permissible Ripple Voltage shall not exceed the value allowed for either C1 or C2 (This will be the same, as the capacitors should be identical.) A B C1 C2 Capacitance: (C1 x C2) / (C1 + C2) Leakage Current: If terminal A is (+), the Leakage Current will be equal to C1's Leakage Current. If terminal B is (+), the Leakage Current will be equal to C2's Leakage Current. 7. Soldering 7.1. Preheating To obtain optimal reliability and solderability conditions, capacitors should be pre-heated at 130 to 200 C for approximately 60 to 120 seconds. 7.2. Soldering The body of the capacitor shall not exceed 260 C during soldering. (1) Reflow Soldering Reflow soldering is a process in which the capacitors are mounted on a printed board with solder paste. There are two methods of Reflow Soldering: Direct and Atmospheric Heat. * Direct Heat (Hot plate) During the Direct Heat method, the capacitor has been positioned on a printed board, which is then placed upon a hot plate. The capacitor maintains a lower temperature than the substrate, which in turn stays at a lower temperature than the hot plate. * Atmospheric Heat a) VPS (Vapor Phase Soldering) During VPS,the substrate is heated by an inert liquid with a high boiling point. The temperature of the capacitor's body and the 11 Temperature of Boards Surface temperature of the substrate are about the same as the atmosphere. This temperature should be below 240C. b) Near and Far IR Ray Due to the heat absorption of the capacitor's body, the internal temperature of the capacitors may be 20 ~ 30C higher than the setting temperature and may exceed 260C. Temperature control is crucial in maintaining a temperature of 260 C or lower. c) Convention Oven An infrared ray is the main source of heat in this process. The temperature of the substrate and the capacitors can be maintained at a similar level by the circulation of heated air, or an inert gas. Pre-heat T3 T2 Reflow Cooling Temperature T1 A1 A2 Time T1=130200 A1= 60120sec. T2=220230 A260sec. T3=260 10 sec. or less than 10 Number of times2 times max.. Time (2) Soldering with a Soldering Iron Soldering with a soldering iron cannot be recommended due to the lack of consistency in maintaining temperatures and process times. If this method should be necessary, the iron should never touch the capacitor's terminals, and the temperature of the soldering iron should never exceed 350C. The application of the iron should not exceed 5 seconds. (3) Please consult us for other methods. 8. Cleaning Cleaning by organic solvent may damage capacitor's appearance and performance.However, our capacitors are not effected even when soaked at 20 ~ 30C 2-propanol for 5 minutes. When introducing new cleaning methods or changing the cleaning term, please consult us. 9. Protective Resin Coating After components are assembled to substrate, a protective resin coating is sometimes applied. As this resin coating cures, it gives mechanical and thermal stress to Tantalum capacitors. This stress can cause damage to the capacitors, which affects their reliability. Before using a resin coating, proper research must be done in regards to the material and process to insure that excessive stress will not be applied to capacitors and other components. 10. Vibration Approximately 300 G shall be applied to a capacitor, when dropped from 1 meter to a concrete floor. Although capacitors are made to withstand this drop test, stress from shock due to falling or striking does cause damage to the capacitors and increases failure rates. Do not subject capacitors to this type of mechanical stress. 11. Ultrasonic cleaning Matsuo does not recommend Ultrasonic cleaning. This may cause damage to the capacitors, and may even cause broken terminals. If the Ultrasonic cleaning process will be used, please note the following: (1)The solvent should not be boiled. (Lower the ultrasonic wave output or use solvent with The high boiling point.) (2)The recommended wattage is less than 0.5 watts per cm 2. (3)The cleaning time should be kept to a minimum. Also, samples must be swang in the solvlent. Please consult us. 12. Additional Notes * When more than one capacitor is connected in series, a resistor that can distribute the voltage equally to the capacitors shall be connected in parallel. * The capacitor cases shall not be cut even if the mounting space is insufficient. * During a customers aging process, voltage should remain under the rated voltage at all times. * Capacitors should never be touched or manipulated while operating. * Capacitors are not meant to be dismantled. * When testing capacitors, please examine the power source before conducting test to insure the tester's polarity and applied voltage. * In the event of a capacitor burning, smoking, or emitting an offensive smell during operation, please turn the circuit "off" and keep hands and face away from the burning capacitor. * If a capacitor be electrical shorted, it becomes hot, and the capacitor element may ignite. In this case, the printed board may be burnt out. * Capacitors should be stored at room temperature under low humidity. Capacitors should never be stored under direct sunlight, and should be stored in an environment containing dust. * If the capacitors will be operated in a humid environment, they should be sealed with a compound under proper conditions. * Capacitors should not be stored or operated in environments containing acids, alkalis or active gasses. * When capacitors are disposed of as "scrap" or waste, they should be treated as Industria Waste since they contain various metals and polymers. * Capacitors submitted as samples should not be used for production purposes. These application notes are prepared based on "Guideline of notabilia for fixed tantalum electrolytic capacitors with solid electrolyte for use in electronic equipment" (EIAJ RCR-2386) issued by Japan Electronics and Information Technology Industries Association (JEITA). For the details of the instructions (explanation, reasons and concrete examples), please refer to this guideline, or consult our Sales Department. R MATSUO MATSUO ELECTRIC CO., LTD. Pleas e f eel f ree t o as k o ur Sales D ep art ment f o r mo re inf ormation o n Tant alum So lid Elec t roly tic Cap ac it o r . Overseas Sales Dep. Head office URL 5-3,3-Chome,Sennari-cho,Toyonaka-shi,Osaka 561-8558,Japan Tel : 06-6332-0883 5-3,3-Chome,Sennari-cho,Toyonaka-shi,Osaka 561-8558,Japan Tel : 06-6332-0871 http://www.ncc-matsuo.co.jp/ Fax : 06-6332-0920 Fax : 06-6331-1386 Specifications on this catalog are subject to change without prior notice. Please inquire of our Sales Department to confirm specifications prior to use. 12