UA741CPS - TEXAS INSTRUMENTS - Datasheet.Directory

1. General description

The PCF2116 is a low-power CMOS LCD controller and driver, designed to drive a split

screen dot matrix LCD display of 1 or 2 lines by 24 characters or 2 or 4 lines by

12 characters with 5 × 8 dot format. All necessary functions for the display are provided in

a single chip, including on-chip generation of LCD bias voltages, resulting in a minimum of

external components and lower system power consumption. The chip contains a

character generator and displays alphanumeric and kana (Japanese) characters. The

PCF2116 interfaces to most microcontrollers using a 4 or 8-bit bus or via the 2-wire

I2C-bus. To allow partial VDD shutdown the ESD protection system of the SCL and SDA

pins does not use a diode connection to VDD.

The ‘x’ in ‘PCF2116x’ represents a specific letter code for a character set in the character

generator ROM (CGROM). The different character sets currently available are specified

by the letters A, C, and G (see Figure 5, Figure 6 and Figure 7). Other character sets are

availab le on reques t.

Remark: The notation for hexadecimal numbers used in this datasheet is consistent with

NXP house style and uses a suffix ‘h’ following the number e.g. 00h.

2. Features

Single chip LCD controller/driver

1 or 2-line display of up to 24 characters per line, or 2 or 4 lines of up to 12 characters

per line

5 × 7 character format plus cursor; 5 × 8 for kana (Japanese syllabary) and user

defined symbols

On chip:

generation of LCD supply voltage (external supply also possible)

generation of intermediate LCD bias voltages

oscillator requires no external components (external clock also possible)

Display data RAM: 80 characters

Character generator ROM: 240 characters

Character gen erator RAM: 16 chara ct ers

4 or 8-bit parallel bus or 2-wire I2C-bus interface

CMOS/TTL compatible

32 row, 60 column outputs

MUX rates 1:32 and 1:16

Uses common 11 code instruction set

Logic supply voltage range, VDD −VSS: 2.5 to 6 V

Display supply voltage range, VDD −VLCD: 3.5 to 9 V

PCF2116 family

LCD controller / drivers

Rev. 05.01 — 20 July 2007 Product data sheet

Product data sheet Rev. 05.01 — 20 July 2007 2 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

Low power consumption

I2C-bus address: 011101 SA0.

3. Applications

Telecom equipment.

Portable instruments.

Point-of-sale terminals.

4. Ordering inf or ma t io n

[1] The letter ‘x’ in the type number represents the letter of the required built-in character set: A, C or G.

Table 1. Ordering information

Type number Package

Name Description Version

PCF2116xU - chip in tray -

PCF2116xU/2 - chip with gold bumps in tray -

PCF2116xU/10 - wafer sawn and delivered on film frame carrier (FFC) -

PCF2116xU/12 - wafer sawn with gold bumps and delivered on film frame carrier (FFC) -

Product data sheet Rev. 05.01 — 20 July 2007 3 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

5. Block diagram

Fig 1. Block diagram of the pcf2116 family

SHIFT REGISTER

32-BIT

coa057

VSS

VDD

CHARACTER

GENERATOR

RAM

(CGRAM)

CHARACTERS

CHARACTER

GENERATOR

ROM

(CGROM)

240

CHARACTERS

CURSOR + DATA CONTROL

SHIFT REGISTER

5 × 12-BIT

DATA LATCHES

COLUMN DRIVERS

BIAS

VOLTAGE

GENERATOR

VLCD

GENERATOR

ROW DRIVERS

DISPLAY DATA RAM

(DDRAM) 80 CHARACTERS

ADDRESS

COUNTER (AC)

INSTRUCTION

DECODER

INSTRUCTION

DATA

FLAG

78 8

I/O BUFFER

LCD

DISPLAY

ADDRESS

COUNTER

POWER-ON

RESET

TIMING

GENERATOR

OSCILLATOR

C1 to C60

R1 to R32

DB0 to DB3 DB4 to DB7 E RS

R/W

PCF2116

SCL SDA SA0

Product data sheet Rev. 05.01 — 20 July 2007 4 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

6. Pinning information

6.1 Pinning

(1) Pad area 0.0121 mm2

(2) Bonding pad dimensions: 110 × 110 μA

Fig 2. Bonding pad location for PCF2116x

coa058

≈ 6.99

≈ 5.64 mm

PCF2116

R24

R23

R22

R21

R20

R19

R18

R17

C31

C32

C30

C33

C34

C35

C36

C37

C38

C39

C21

C22

C23

C24

C25

C26

C27

C28

C29

C16

C17

C18

C19

C20

C10

C11

C12

C13

C14

C15

SA0

R/W

OSC

DB1

DB0

R25

R26

R27

R28

R29

R30

R31

R16

R10

R11

R12

R13

R14

R15

C40

C41

C42

C43

C44

C45

C47

C48

C46

C49

C50

C51

C52

C53

C54

C55

C56

C57

C58

C59

C60

R32

DB7

SCL

DB6

SDA

DB5

DB4

DB3

DB2

VLCD1

VLCD2

VLCD3

VDD2

VDD1

VSS1

VSS2

Product data sheet Rev. 05.01 — 20 July 2007 5 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

6.2 Pin description

Table 2. Pad allocation table

Symbol Pad Symbol Pad

OSC 1 C29 to C1 60 to 88

DB1 2 R24 to R17 89 to 96

VDD2 3 R8 to R1 97 to 104

DB0 4 DB7 105

VDD1 5SCL106

SA0 6 DB6 107

E7SDA108

VSS1 8DB5109

R/W 9V

0110

T1 10 VLCD1 111

VSS2 11 DB4 112

RS 12 VLCD2 113

R9 to R16 13 to 20 DB3 114

R25 to R32 21 to 28 VLCD3 115

C60 to C30 29 to 59 DB2 116

Table 3. Bonding pad description

All x/y coordinates represent the position of the centre of each pad with respect to the centre

(x/y = 0) of the chip (see Figure 2).

Symbol Pad X (μm) Y (μm) Description

OSC 1 −2445 −3300 oscillator/extern al clock inpu t

DB1 2 −2211 −3300 1 bit of 8 bit bi-directional data bus

VDD2 3−2034 −3300 suppl y voltag e 2

DB0 4 −1806 −3300 1 bit of 8 bit bi-directional data bus

VDD1 5−1627 −3300 suppl y voltag e 1

SA0 6 −1437 −3300 I2C-bus address pin

E7−1245 −3300 data bus clock input (parallel control)

VSS1 8−1056 −3300 logic ground 1

R/W 9 −867 −3300 read/write input (parallel control)

T1 10 −672 −3300 test pad (connect to VSS)

VSS2 11 −486 −3300 l ogic ground 2

RS 12 −297 −3300 register select input (parallel control)

R9 13 77 −3300 LCD row driver output 9

R10 14 247 −3300 LCD row driver output 10

R11 15 417 −3300 LCD row driver output 11

R12 16 587 −3300 LCD row driver output 12

R13 17 757 −3300 LCD row driver output 13

R14 18 927 −3300 LCD row driver output 14

R15 19 1097 −3300 LCD row driver output 15

R16 20 1267 −3300 LCD row driver output 16

Product data sheet Rev. 05.01 — 20 July 2007 6 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

R25 21 1436 −3300 LCD row driver output 25

R26 22 1606 −3300 LCD row driver output 26

R27 23 1776 −3300 LCD row driver output 27

R28 24 1976 −3300 LCD row driver output 28

R29 25 2116 −3300 LCD row driver output 29

R30 26 2286 −3300 LCD row driver output 30

R31 27 2456 −3300 LCD row driver output 31

R32 28 2626 −3013 LCD row driver output 32

C60 29 2626 −2760 LCD column driver output 60

C59 30 2626 −2590 LCD column driver output 59

C58 31 2626 −2420 LCD column driver output 58

C57 32 2626 −2250 LCD column driver output 57

C56 33 2626 −2080 LCD column driver output 56

C55 34 2626 −1910 LCD column driver output 55

C54 35 2626 −1740 LCD column driver output 54

C53 36 2626 −1570 LCD column driver output 53

C52 37 2626 −1400 LCD column driver output 52

C51 38 2626 −1230 LCD column driver output 51

C50 39 2626 −1060 LCD column driver output 50

C49 40 2626 −890 LCD column driver output 49

C48 41 2626 −720 LCD column driver output 48

C47 42 2626 −550 LCD column driver output 47

C46 43 2626 −380 LCD column driver output 46

C45 44 2626 582 LCD column driver output 45

C44 45 2626 752 LCD column driver output 44

C43 46 2626 922 LCD column driver output 43

C42 47 2626 1092 LCD column driver output 42

C41 48 2626 1262 LCD column driver output 41

C40 49 2626 1432 LCD column driver output 40

C39 50 2626 1602 LCD column driver output 39

C38 51 2626 1772 LCD column driver output 38

C37 52 2626 1942 LCD column driver output 37

C36 53 2626 2112 LCD column driver output 36

C35 54 2626 2282 LCD column driver output 35

C34 55 2626 2452 LCD column driver output 34

C33 56 2626 2622 LCD column driver output 33

C32 57 2626 2792 LCD column driver output 32

C31 58 2626 2962 LCD column driver output 31

C30 59 2626 3132 LCD column driver output 30

Table 3. Bonding pad description …continued

All x/y coordinates represent the position of the centre of each pad with respect to the centre

(x/y = 0) of the chip (see Figure 2).

Symbol Pad X (μm) Y (μm) Description

Product data sheet Rev. 05.01 — 20 July 2007 7 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

C29 60 2339 3302 LCD column driver output 29

C28 61 2169 3302 LCD column driver output 28

C27 62 1999 3302 LCD column driver output 27

C26 63 1829 3302 LCD column driver output 26

C25 64 1659 3302 LCD column driver output 25

C24 65 1489 3302 LCD column driver output 24

C23 66 1319 3302 LCD column driver output 23

C22 67 1149 3302 LCD column driver output 22

C21 68 979 3302 LCD column driver output 21

C20 69 809 3302 LCD column driver output 20

C19 70 639 3302 LCD column driver output 19

C18 71 469 3302 LCD column driver output 18

C17 72 299 3302 LCD column driver output 17

C16 73 129 3302 LCD column driver output 16

C15 74 −245 3302 LCD column driver output 15

C14 75 −415 3302 LCD column driver output 14

C13 76 −585 3302 LCD column driver output 13

C12 77 −755 3302 LCD column driver output 12

C11 78 −925 3302 LCD column driver output 11

C10 79 −1095 3302 LCD column driver output 10

C9 80 −1265 3302 LCD column driver output 9

C8 81 −1435 3302 LCD column driver output 8

C7 82 −1605 3302 LCD column driver output 7

C6 83 −1775 3302 LCD column driver output 6

C5 84 −1945 3302 LCD column driver output 5

C4 85 −2115 3302 LCD column driver output 4

C3 86 −2285 3302 LCD column driver output 3

C2 87 −2455 3302 LCD column driver output 2

C1 88 −2625 3015 LCD column driver output 1

R24 89 −2625 2846 LCD row driver output 24

R23 90 −2625 2676 LCD row driver output 23

R22 91 −2625 2506 LCD row driver output 22

R21 92 −2625 2336 LCD row driver output 21

R20 93 −2625 2166 LCD row driver output 20

R19 94 −2625 1996 LCD row driver output 19

R18 95 −2625 1826 LCD row driver output 18

R17 96 −2625 1656 LCD row driver output 17

R8 97 −2625 1487 LCD row driver output 8

R7 98 −2625 1317 LCD row driver output 7

Table 3. Bonding pad description …continued

All x/y coordinates represent the position of the centre of each pad with respect to the centre

(x/y = 0) of the chip (see Figure 2).

Symbol Pad X (μm) Y (μm) Description

Product data sheet Rev. 05.01 — 20 July 2007 8 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

7. Pin functions

7.1 RS: register select (para llel control)

RS select s the register to be accessed for read and write when the device is controlled by

the parallel interface. RS = logic ‘0’ selects the instruction register for write and the Busy

Flag and Address Counter for read. RS = logic ‘1’ selects the data register for both read

and write. There is an internal pull-up on pin RS.

7.2 R/W: read/write (parallel control)

R/W selects either the read (R/W = logic ‘1’) or wr ite (R/ W = logic ‘0’) operation when

control is by the parallel interface. There is an internal pull-up on this pin.

7.3 E: data bus clock

The E pin is set HIGH to signal the start of a read or write operation when the device is

controlled by the parallel interface. Data is clocked in or out of the chip on the negative

edge of the clock. Note that this pin must be connected to logic ‘0’ (VSS) when the I2C-bus

control is used.

R6 99 −2625 1147 LCD row driver output 6

R5 100 −2625 977 LCD row driver output 5

R4 101 −2625 807 LCD row driver output 4

R3 102 −2625 637 LCD row driver output 3

R2 103 −2625 467 LCD row driver output 2

R1 104 −2625 297 LCD row driver output 1

DB7 105 −2625 −290 1 bit of 8 bit bi-directional data bus

SCL 106 −2625 −479 I2C-bus serial cloc k input

DB6 107 −2625 −716 1 bit of 8 bit bi-directional data bus

SDA 108 −2625 −976 I2C-bus serial data input/output

DB5 109 −2625 −1202 1 bit of 8 bit bi-directional data bus

V0110 −2625 −1388 control input for VLCD

VLCD1 111 −2625 −1580 LCD supply voltage input/output 1

DB4 112 −2625 −1808 1 bit of 8 bit bi-directional data bus

VLCD2 113 −2625 −1985 LCD supply voltage input/output 2

DB3 114 −2625 −2213 1 bit of 8 bit bi-directional data bus

VLCD3 115 −2625 −2390 LCD supply voltage input/output 3

DB2 116 −2625 −2621 1 bit of 8 bit bi-directional data bus

Table 3. Bonding pad description …continued

All x/y coordinates represent the position of the centre of each pad with respect to the centre

(x/y = 0) of the chip (see Figure 2).

Symbol Pad X (μm) Y (μm) Description

Product data sheet Rev. 05.01 — 20 July 2007 9 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

7.4 DB0 to DB7: data bus

The bidirectional, 3-state data bus transfers data between the system controller and the

PCF2116. DB7 may be used as the Busy Flag signalling that internal operations are not

yet complet. In 4-bit operations the 4 higher order lines DB4 to DB7 are used; DB0 to DB3

must be left open circuit. There is an internal pull-up on each of the data lines. Note that

these pins must be left open circuit when the I2C-bus control is used.

7.5 C1 to C60: column driver outputs

These pins output the data for pairs of columns.This arrangement permits an optimized

chip-on-glass (COG) design for 4-line, 12 character layouts.

7.6 R1 to R32: row driver output s

These pins output the row select waveforms to the left and right halves of the display.

7.7 VLCD: LCD power supply

Negative power supply for the liquid crystal display.

This may be generated on-chip or supplied externally.

7.8 V0: VLCD control input

The input level at this pin determines the generated VLCD output voltage.

7.9 OSC : osci llator

When the on-chip oscillator is used this pin must be connected to VDD. This pin is the input

for an external clock signal, if used.

7.10 SCL: se rial clock line

Input for the I2C-b us cl oc k si gna l.

7.11 SDA: serial data line

Input/output for the I2C-bus data line.

7.12 SA0: address pin

The hardware sub-address line is used to program the device sub-address for 2 different

PCF2116s on the same I2C-bus.

7.13 T1: test pad

Must be connected to VSS. Not user accessible.

8. Functional description

8.1 LCD supply voltage generator for PCF2116x

The on-chip voltage generator is controlled by bit G of the ‘Function set’ instruction

and V0.

Product data sheet Rev. 05.01 — 20 July 2007 10 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

V0 is a high-impedance input and draws no current from the system power supply. Its

range is between VSS and VDD −1 V. When V0 is connected to VDD the generator is

switched off and an external voltage must be supplied to pin VLCD. This can be more

negative than VSS.

When G = logic ‘1’ the generator produces a negative voltage at pin VLCD, controlled by

the input voltage at pin V0. The LCD operating voltage is given by the relationship:

Where:

and

When G = logic ‘0’, the generated output voltage VLCD is equal to V0 (between VSS and

VDD). In this instance:

When VLCD is generated on-chip the VLCD pin must be de-coupled to VDD with a suitable

capacitor . VDD and V0 must be selected to limit the maximum value of VOP to 9 V. Figure 3

and Figure 4 show the two generator control characteristics.

(1) High voltage mode: VOP = 1.8VDD − V0

Fig 3. VOP as a function of V0 control characteristics (1)

1.8V

–

()

LCD

–

()

LCD

0.8V

–

()

–=

mga798

3.50123456

6 = V

OP(min)

= 0.8 × V

OP(max)

= 1.8 × V

2.5

G = 1

Product data sheet Rev. 05.01 — 20 July 2007 11 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

8.2 Character generator ROM (CGROM)

The character generator ROM generates 240 character patterns in 5 ×8 dot format from

8-bit character codes. Figure 5, Figure 6 and Figure 7 show the cha racter sets curren tly

available.

The standard character sets A, C and G are available for the PCF2116x.

(1) Buffer mode: VOP = VDD − V0

Fig 4. VOP as a function of V0 control characteristics (2)

mga799

3.50123456

6 = VDD

G = 0

Product data sheet Rev. 05.01 — 20 July 2007 12 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

Fig 5. Character set ‘A’ in CGROM: PC F2116A

mlb245

0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111

upper

4 bits

lower

6 bits

xxxx 0000

xxxx 0001

xxxx 0010

xxxx 0011

xxxx 0100

xxxx 0101

xxxx 0110

xxxx 0111

xxxx 1000

xxxx 1001

xxxx 1010

xxxx 1011

xxxx 1100

xxxx 1101

xxxx 1110

xxxx 1111 16

Product data sheet Rev. 05.01 — 20 July 2007 13 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

Fig 6. Character set ‘C’ in CGROM: PCF2116C

mlb895

0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111

upper

4 bits

lower

4 bits

xxxx 0000

xxxx 0001

xxxx 0010

xxxx 0011

xxxx 0100

xxxx 0101

xxxx 0110

xxxx 0111

xxxx 1000

xxxx 1001

xxxx 1010

xxxx 1011

xxxx 1100

xxxx 1101

xxxx 1110

xxxx 1111 16

RAM 1

Product data sheet Rev. 05.01 — 20 July 2007 14 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

Fig 7. Character set ‘G’ in CGROM: PCF2116G

mlb89

0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111

upper

4 bits

lower

6 bits

xxxx 0000

xxxx 0001

xxxx 0010

xxxx 0011

xxxx 0100

xxxx 0101

xxxx 0110

xxxx 0111

xxxx 1000

xxxx 1001

xxxx 1010

xxxx 1011

xxxx 1100

xxxx 1101

xxxx 1110

xxxx 1111 16

RAM 1

Product data sheet Rev. 05.01 — 20 July 2007 15 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

8.3 LCD bi as voltage generator

The intermediate bias voltages for the LCD display are also generated on-chip. This

removes the need for external bias chain resistors and significantly reduces the system

power consumption. The optimum levels depend on the multiplex rate and are selected

automatically when the number of lines in the display is defined.

The optimum value of VOP depends on the multiplex rate, the LCD threshold voltage (Vth)

and the number of bias levels and is given by the relationships in Table 4. Using a 5-level

bias scheme for 1:16 MUX rate allows VOP < 5 V for most LCD liquids. The effect on the

display contrast is negligible.

8.4 Oscillator

The on-chip oscillator provides the clock signal for the display system. No external

components are required. Pin OSC must be connected to VDD.

8.5 External clock

If an external clock is to be used, it must be input at pin OSC. The resulting display frame

frequency is given by fframe =1⁄2304 fosc . A clock signal must always be present, otherwise

the LCD is frozen in a DC state.

8.6 Power-on reset

The power-on reset block initializes the chip after power-on or power failure.

8.7 Registers

The PCF2116 has two 8-bit registers, an Instruction Register (IR) and a Data Register

(DR). The Register Select signal (RS) determines which register will be accessed.

The instruction register stores instruction codes such as ‘Display clear’ and ‘Cursor shift’,

and address information for the Display Data RAM (DDRAM) and Character Generator

RAM (CGRAM). The instruction register can be written to, but not read, by the system

controller.

The data register temporarily stores data to be read from the DDRAM and CGRAM. When

reading, data from the DDRAM or CGRAM corresponding to the address in the Address

Counter is written to the data register prior to being read by the ‘Read data’ instruction.

8.8 Busy flag

The Busy Flag indicates the free/busy status of the PCF2116. Logic ‘1’ indicates that the

chip is busy and further instructions will not be accepted. The Busy Flag is output to pin

DB7 when RS = logic ‘0’ and R/W = logic ‘1’. Instructions must only be written after

checking that the Busy Flag is logic ‘0’ or waiting for the required number of clock cycles.

Table 4. Optimum values for VOP

MUX rate Number of bias

levels VOP/Vth Discrimination

Von/Voff

1:16 5 3.67 1.277

1:32 6 5.19 1.196

Product data sheet Rev. 05.01 — 20 July 2007 16 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

8.9 Address counter (AC)

The Address Counter assigns addresses to the DDRAM and CGRAM for reading and

writing and is set by the instructions ‘Set CGRAM address’ and ‘Set DDRAM address’.

After a read/write operation the Address Counter is automatically incremented or

decremented by 1.The Address Counter contents are output to the bus (DB0 to DB6)

when RS = logic ‘0’ and R/W = logic ‘1’.

8.10 Display data RAM (DDRAM)

The display data RAM stores up to 80 characters of display data represented by 8-bit

character codes. RAM locations not used for storing display data can be used as general

purpose RAM. The basic DDRAM-to-display mapping scheme is shown in Figure 8 and

Figure 9.

Wit h no display shift the characters represented by the codes in the first 12 or 24 RAM

locations starting at address 00 in line 1 are displayed. Subsequent lines display data

starting at addresses 20h, 40h, or 60h. Figure 10, Figure 11, Figure 12 and Figure 13

show the DDRAM-to-display mapping principle when the display is shifted.

Fig 8. DDRAM-to display mapping (1); no shift.

Fig 9. DDRAM-to display mapping (2); no shift.

12345 22 23 24

00 01 02 03 04 15 16 17 18 19 4C 4D 4E 4F

non-displayed DDRAM addresses

isplay

osition

(

decimal)

DRAM

ddress

(

hex) 1-line display

64 65 66 67

40 41 42 43 44 55 56 57 58 59

00 01 02 03 04 15 16 17 18 19 24 25 26 27

non-displayed DDRAM address

DDRAM

(hex)

Address

2-line display

line

mla792

123456789101112

non-displayed DDRAM addresses

DRAM

ddress

(

hex)

4 line display

00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13

20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 30 31 32 33

40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4E 4F 50 51 52 53

60 61 62 63 64 65 66 67 68 69 6A 6B 6C 6D 6E 6F 70 71 72 73

line

mla793

Product data sheet Rev. 05.01 — 20 July 2007 17 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

The display address ranges are shown in Table 5.

For 2 and 4-line displays the end address of one line and the start address of the next line

are not consecutive. When the display is shifted each line wraps around independently of

the others (Figure 10, Figure 11, Figure 12 and Figure 13).

When data is written into the DDRAM wrap-around occurs from 4F to 00 in 1-line mode

and from 27 to 40 and 67 to 00 in 2-line mode; from 13 to 20, 33 to 40, 53 to 60 and

73 to 00 in 4-line mode.

Fig 10. DDRAM-to display mapping (1); right shift. Fig 11. DDRAM-to display mapping (2); right shift.

27 00 01 02 03

67 40 41 42 43

14 15 16

54 55 56

DRAM

ddress

(

hex)

line

2-line display

12345 222324

4F 00 01 02 03 14 15 16

Display

osition

(

decimal)

DRAM

ddress

(

hex) 1-line display

mla802

13 01 02 03 04 05 06 07 08 09 0A

20 21 22 23 24 25 26 27 28 29 2A33

40 41 42 43 44 45 46 47 48 49 4A53

60 61 62 63 64 65 66 67 68 69 6A73

123456789101112

DRAM

ddress

(

hex)

line

4-line display

mla803

Fig 12. DDRAM-to display mapping (1); left shift. Fig 13. DDRAM-to display mapping (2); left shift.

12345 222324

0501 02 03 04 16 17 18

41 42 43 44 45 56 57 58

0501 02 03 04 16 17 18

Display

osition

(

decimal)

DRAM

ddress

(

hex)

DDRAM

Address

(hex)

line

1-line display

2-line display mla815

01 02 03 04 05 06 07 08 09 0A 0B 0C

21 22 23 24 25 26 27 28 29 2A 2B 2C

41 42 43 44 45 46 47 48 49 4A 4B 4C

61 62 63 64 65 66 67 68 69 6A 6B 6C

123456789101112

DRAM

ddress

(

hex)

line

4-line display

mla81

Table 5. Display address ranges

1-line display 2-line di splay 4-line display

00 to 4F line 1: 00 to 27 line 1: 00 to 13

- line 2: 40 to 67 line 2: 20 to 33

- - line 3: 40 to 53

- - line 4: 60 to 73

Product data sheet Rev. 05.01 — 20 July 2007 18 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

8.11 Character generator RAM (CGRAM)

Up to 16 user-defined characters may be stored in the character generator RAM. The

CGROM and CGRAM use a common address space, of which the first column is reserved

for the CGRAM (see Figure 5). Figure 14 shows the addressing principle for the CGRAM.

8.12 Cursor control circuit

The cursor control circuit generates the cursor (underline and/or character blink as shown

in Figure 15) at the DDRAM address contained in the Address Counter. When the

Address Counter contains the CGRAM address the cursor will be inhibited.

Character code bits 0 to 3 cor respond to CGRAM address bits 3 to 6.

CGRAM address bits 0 to 2 designate character pattern line position. The 8th line is the cursor

position and display is performed by logical OR with the cursor. Data in the 8th line will appear

in the cursor position.

Character pattern column positions correspond to CGRAM data bits 0 to 4, as shown in

Figure 14 (bit 4 being at the left end).

As shown in Figure 5 and Figure 14, CGRAM character patterns are selected when character

code bits 4 to 7 are all logic 0. CGRAM data = logic 1 corr esponds to selection for display.

Only bits 0 to 5 of the CGRAM address are set by the ‘Set CGRAM address’ instruction. Bit 6

can be set using the ‘Set DDRAM address’ instruction or by using the auto-increment feature

during CGRAM write. All bits 0 to 6 can be read using the ‘Read busy flag and address’

instruction.

Fig 14. Relationship between CGRAM addresses and data / display patterns

mga800

76543210 6543210 43210

higher

order

bits

lower

order

bits

lower

order

bits

higher

order

bits

lower

order

bits

higher

order

bits

00000000 0000000 0

001 000

010 000

011 0

100 0 00

101 00 0

110 000

111 00000

000 000

001 0 0 0

010 00 00011

100

101 00 00

110 00 00

111 00000

001

00000001 0001

00000010

00001111

0100000

100

101

110

111

character codes

(DDRAM data)

CGRAM

address

character patterns

(CGRAM data)

characte

pattern

example

cursor

position

characte

pattern

example

Product data sheet Rev. 05.01 — 20 July 2007 19 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

8.13 Timing generat or

The timing generator produces the various signals required to drive the internal circuitry.

Internal chip operation is not disturbed by operations on the data buses.

8.14 LCD row and column drivers

The PCF21 16 contains 32 row and 60 column drivers, which connect the appropriate LCD

bias voltages in sequence to the display, in accordance with the data to be displayed. The

bias voltages and the timing are selected automatically when the number of lines in the

display is selected. Figure 16 and Figure 17 show typical waveforms.

In 1-line mode (1:16) the row outputs are driven in pairs: R1/R17, R2/R18 for example.

This allows the output pairs to be connected in parallel, providing greater drive capability.

Unused outputs should be left unconnected.

Fig 15. Cursor and blink display examples

mga80

cursor

5 x 7 dot character font alternating display

ursor display example blink display example

Product data sheet Rev. 05.01 — 20 July 2007 20 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

Fig 16. Typical LCD waveforms; 1-line mode

mga802

ROW 1

COL 1

state 1 (ON

)

state 2 (ON

)

0.25 VOP

0 V

tate 1

1-line display

(1:16)

frame n 1frame n

ROW 9

ROW 2

COL 2

tate 2

123 16123 16

VDD

VLCD

V3/V4

VDD

VLCD

V3/V4

VDD

VLCD

V3/V4

VDD

VLCD

V3/V4

VDD

VLCD

V3/V4

−0.25 VOP

0.25 VOP

0 V

−0.25 VOP

VOP

−VOP

VOP

Product data sheet Rev. 05.01 — 20 July 2007 21 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

Fig 17. Typical LCD waveforms; 2-line mode

mga803

VDD

VLCD

VDD

VLCD

VDD

VLCD

VDD

VLCD

VDD

VLCD

ROW 1

COL 1

state 1 (ON

)

state 2 (ON

)

0.15 VOP

0 V

VOP

−VOP

tate 1

2-line display

(1:32)

frame n + 1frame n

ROW 9

ROW 2

COL 2

−0.15 VOP

0.15 VOP

0 V

−0.15 VOP

VOP

tate 2

123 32123 32

Product data sheet Rev. 05.01 — 20 July 2007 22 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

8.15 Reset function

The PCF2116 automatically initializes (resets) when power is turned on. After reset the

chip has the following state (see Table 6):

9. Instructions

Only two PCF2116 registers, the Instruction Register (IR) and the Data Register (DR) are

directly controlled by the microcontroller. Before internal operation, control information is

stored temporarily in these registers to allow an interface to various types of

microcontrollers which operate at different speeds or to allow an interface to peripheral

control ICs.

PCF2116 opera tio n is con tro ll ed by the inst ruc tio ns shown in Table 8 toge ther with their

execution time.

There are 4 categories of instructions, those that:

•designate PCF2116 functions such as display format, data length, etc.

•set internal RAM addresses

•perform data transfer with internal RAM

•others.

In n ormal use, the da ta trans fer in struct ions are used m ost f reque ntly. Howev er , aut omatic

incrementing by 1 (or decrementing by 1) of internal RAM addresses after each data write

lessens the microcontroller program load. The display shift in particular can be performed

concurrently with display data write, enabling the designer to develop systems in minimum

time with maxim um progr am ming efficien cy.

During internal operation no instruction other than ‘Read busy flag and address’ is

executed.

Table 6. State afte r rese t

Step Description

1 displ ay cl ear

2 function set DL = 1 8-bit interface

M, N = 0 1-line display

G = 0 voltage generator;

VLCD = V0

3 display on/off control D = 0 display off

C = 0 cursor off

B = 0 blink off

4 entry mode set I/D = 1 +1 increment

S = 0 no shift

5 Default address pointer to DDRAM. The Busy Flag (BF) indicates the

busy state (BF = logic ‘1’) until initialization ends. The busy state lasts

for 2 ms. The chip can also be initialized by software.

(see Figure 18 and Figure 29).

2C-bus interface reset

Product data sheet Rev. 05.01 — 20 July 2007 23 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

Because the Busy Flag is set to logic ‘1’ while an instruction is being executed, check to

make sure it is on logic ‘0’ before sending the next instruction or wait for the maximum

instruction execution time, as given in Table 8. An instruction sent while the Busy Flag is

HIGH will not be executed.

Table 7. Command bit identities

Bit 0 1

I/D decrement increment

S display freeze display shift

D d isplay off dis play on

C cursor off cursor on

B character at cursor position does not

blink character at cursor position blinks

S/C cursor move display shift

R/L lef t sh if t right shi f t

DL 4 bits 8 bits

G voltage generator: VLCD = V0 voltage generator;

VLCD = V0 - 0.8VDD

N, (M = 0)

PCF2116x 1 line × 24 characters; MUX 1:16 2 lines ×24 characters; MUX 1:32

N, ( M = 1) reserved 4 lines × 12 characters; MUX 1:32

BF end of internal operat ion internal operati on in pr og res s

Co last control byte, only data bytes to

follow next two bytes are a data byte and

another control byte

xxxxxxxx xxxxxxxxxxx xx xxxxxxxxxx xxxxxxxxxxx xxxxx xxxxxxx x x x xx xxxxxxxxxxx xxxxxxxxxxx xxxxxx xxxxxx xxxxxxxxxxxxx xx xx xxxxx

xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x

xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx

xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx

Product data sheet Rev. 05.01 — 20 July 2007 24 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

[1] In the I2C-bus mode the DL bit is don't care. 8-bit mode is assumed.

[2] In the I2C-bus mode a control byte is required when RS or R/W is changed; control byte: Co, RS, R/W, 0, 0, 0, 0, 0; command byte: DB7 to DB0.

[3] Examp le: fosc = 150 kHz, ; 3 cycles = 20 μs, 165 cycles = 1.1 ms.

Table 8. Instruction s

Instruction RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Description Required

clock cycles

NOP 0000000000No operation. 0

Clear display 0000000001Clears entire display and sets

DDRAM address 0 in Address

Counter.

165

Return Home 0000000010Sets DDRAM address0 in Address

Counter. Also returns shifted

display to original po sition . DDRAM

contents remain unchanged.

Entry mode set 00000001I/DSSets cursor move direction and

specifi es shift of disp la y. Thes e

operations are performed during

data write and read.

Display control 0000001DCBSets entire display on/off (D),

cursor on/o f f (C) and bl ink of curs or

position character (B).

Cursor/display shift000001S/CR/L00Moves cursor and shifts display

without changing DDRAM contents. 3

Function set 00001DLNMG0Sets interface data length (DL),

number of display lines (N, M) and

volt a ge gen erat or cont rol (G).

Set CGRAM address0001ACG Sets CGRAM address. 3

Set DDRAM address001ADD Sets DDRAM address. 3

Read busy flag and

address 0 1 BF AC Reads Busy Flag (BF) indicating

internal operation is being

performed and reads Address

Counter con ten t s .

Read data 1 1 read data Reads data from CGRAM or

DDRAM. 3

Write data 1 0 write data Writes data to CGRAM or DDRAM. 3

fOSC

------------ 6.67μ

xxxxxxxx xxxxxxxxxxx xx xxxxxxxxxx xxxxxxxxxxx xxxxx xxxxxxx x x x xx xxxxxxxxxxx xxxxxxxxxxx xxxxxx xxxxxx xxxxxxxxxxxxx xx xx xxxxx

xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x

xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx

xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx

Product data sheet Rev. 05.01 — 20 July 2007 25 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

Fig 18. I2C-bus timing diagram; rise and fall times refer to VIL and VIH

mga811

tHIGH

tLOW

tHD;STA

tBUF

SDA

SCL

t/fSCL

tSU;STO

START

CONDITION

(S)

BIT 7

MSB

(A7)

BIT 6

(A6) BIT 0

LSB

R/W

ACKNOWLEDGE

(A) STOP

CONDITION

(P)

ROTOCOL

Product data sheet Rev. 05.01 — 20 July 2007 26 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

Fig 19. 4-bit transfer example

(1) IR7, IR3: instruction 7th bit, 3rd bit.

(2) AC3: Address counter 3rd bit.

Fig 20. 4-bit transfer timing sequence

mga804

instruction

write busy flag and

address counter read data register

read

IR7 IR3 BF AC3 DR7 DR3

IR6 IR2 AC6 AC2 DR6 DR2

IR5 IR1 AC5 AC1 DR5 DR1

IR4 IR0 AC4 AC0 DR4 DR0

mga80

nternal

DB7

R/W

internal operation

IR7 IR3 AC3 D7 D3

not

busy

AC3

busy

instruction

write busy flag

check busy flag

check instruction

write

Product data sheet Rev. 05.01 — 20 July 2007 27 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

9.1 Clear display

‘Clear display’ writes space code 20h into all DDRAM addresses (The character pattern

for character code 20 must be a blank pattern). Sets the DDRAM Address Counter to

logic ‘0’. Returns the display to its original position if it was shifted. So, the display

disappears and the cursor or blink position goes to the left edge of the display

(the first line if 2 or 4 lines are displayed). Sets entry mode I/D = logic ‘1’ (increment

mode). S of entry mode does not change.

The instruction ‘Clear display’ requires extra execution time. This is accommodated by

checking the busy-flag (BF) or waiting for 2 ms. The latter must be applied where no

read-back options are foreseen, as in some chip-on-glass (COG) applications.

9.2 Return home

‘Return home’ sets the DDRAM Address Counter to logic ‘0’ and returns the display to its

original position if it was shifted. The DDRAM contents do not change. The cursor or blink

position goes to the left of the display (the first line if 2 or 4 lines are displayed). I/D and S

of entry mode do not change.

9.3 Entry mode set

9.3.1 I/D

When I/D = logic ‘1’ (or ‘0’) the DDRAM or CGRAM address increments (or decrements)

by 1 when data is written into or read from the DDRAM or CGRAM. The cursor or blink

position moves to the right when incremented and to the left when decremented. The

cursor and blink are inhibited when the CGRAM is accessed.

9.3.2 S

When S = logic ‘1’, the entire display shifts either to the right (I/D = logic ‘0’) or to the left

(I/D = logic ‘1’) during a DDRAM write. So, it looks as if the cursor stands still and the

display moves. The display does not shift when reading from the DDRAM, or when writing

into or reading from the CGRAM. When S = logic ‘0’ the display does not shift.

Fig 21. Busy flag check timing sequence

mga80

instruction

write busy flag

check busy flag

check instruction

write

internal operation

nternal

DB7

R/W

data busy busy not

busy data

Product data sheet Rev. 05.01 — 20 July 2007 28 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

9.4 Display on/off control

9.4.1 D

The display is on when D = logic ‘1’ and off when D = logic ‘0’. Display data in the DDRAM

is not affected and can be displayed immediately by setting D to logic ‘1’.

9.4.2 C

The cursor is displayed when C = logic ‘1’ and inhibited when C = logic ‘0’. Even if the

cursor disappears, the display functions e.g. I/D, remain in operation during display data

write. The cursor is displayed using 5 dots in the 8th line (see Figure 15).

9.4.3 B

The character indicated by the cursor blinks when B = logic ‘1’. The blink is displayed by

switching between display characters and all dots on with a period of 1 second when

fosc = 150 kHz (see Figure 15). At other clock frequencies the blink period is equal to

150 kHz/fosc.

The cursor and the blink can be set to display simultaneously.

9.5 Cursor display shift

‘Cursor/display shift’ moves the cursor position or the display to the right or left without

writing or reading display data. This function is used to correct a character or move the

cursor through the display . In 2 or 4-line displays, the cursor moves to the next line when it

passes the last position (40 or 20 decimal) of the line. When the displayed data is shifted

repeatedly all lines shift at the same time; displayed characters do not shift into the next

line.

The Address Counter (AC) content does not change if the only action performed is shift

display, but increments or decrements with the cursor shift.

9.6 Function set

9.6.1 DL (parallel mode only)

Defines interface data width when the parallel data interface is used.

Data is sent or received in bytes (bits DB7 to DB0) when DL = logic ‘1’, or in two 4-bit

nibbles (DB7 to DB4) when DL = logic ‘0’. When 4-bit width is selected, data is transmitted

in two cycles using the parallel bus.

In a 4-bit application DB3 to DB0 are left open (internal pull-ups). Hence in the first

‘Function set’ instruction after power-on, G and H are set to 1. A second ‘Function set’

must then be sent (2 nibbles) to set G and H to their required values.

When using the I2C-bus interface the DL should not previously have been set to 0 using

the parallel interface.

9.6.2 N, M

Sets the number of display lines.

Product data sheet Rev. 05.01 — 20 July 2007 29 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

9.6.3 G

Controls the VLCD voltage generator characteristic.

9.7 Set CGRAM address

‘Set CGRAM address’ sets bit 0 to 5 of the CGRAM address (ACG in Table 8 ) into the

Address Counter (binary A[5] to A[0]). Data can then be written to or read from the

CGRAM.

Only bits 0 to 5 of the CGRAM address are set by the ‘Set CGRAM address’ instruction.

Bit 6 can be set using the ‘Set DDRAM address’ instruction or by using the auto-increment

feature during CGRAM write. All bits 0 to 6 can be read using the ‘Read busy flag and

address’ instruction.

9.8 Set DDRAM address

‘Set DDRAM address’ sets the DDRAM address (ADD in Table 8) into the Address

Counter (binary A[6] to A[0]). Data can then be written to or read from the DDRAM.

9.9 Read busy flag and address

‘Read busy flag and address’ reads the Busy Flag (BF). BF = logic 1 indicates that an

internal operation is in progress. The next instruction will not be executed until

BF = logic 0, so BF should be checked before sending another instruction.

At the same time, the value of the Address Counter (AC in Table 8) expressed in binary

A[6] to A[0] is read out. The Address Counter is used by both CGRAM and DDRAM, and

its value is determined by the previous instruction.

9.10 Write data to CGRAM or DDRAM

Writes binary 8-bit data D[7] to D[0] to the CGRAM or the DDRAM.

Whether the CGRAM or DDRAM is to be written into is determined by the previous

specification of the CGRAM or DDRAM address setting.

After writing, the address automatically increments or decrements by 1, in accordance

with the entry mode. Only bits D[4] to D[0] of CGRAM data are valid, bits D[7] to D[5] are

‘don’t care’ CGRAM addresses.

9.11 Read dat a from CGRAM or DDRAM

Reads binary 8-bit data D[7] to D[0] from the CGRAM or DDRAM.

The most recent ‘Set address’ instruction determines whether the CGRAM or DDRAM is

to be read.

Table 9. Hexadecimal address ranges (pcf2116)

Address (h) Function

00 to 4F 1-line by 24

00 to 27 and 40 to 67 2-lines by 24

00 to 13, 20 to 33, 40 to 53 and 60 to 73 4-lines by 12

Product data sheet Rev. 05.01 — 20 July 2007 30 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

The ‘Read data’ instruction gates the content of the data register (DR) to the bus while

E = HIGH. After E goes LOW again, internal operation increments (or decrements) the AC

and stores RAM data corresponding to the new AC into the DR.

Remark: the only three instructions which update the data register (DR) are:

•‘Set CGRAM address’

•‘Set DDRAM address’

•‘Read data’ from CGRAM or DDRAM.

Other instructions (e.g. ‘Write data’, ‘Cursor/Display shift’, ‘Clear display’, ‘Return home’)

do not modify the dat a register content.

10. Interface to microcontroller (parallel interface)

The PCF2116 can send data in either two 4-bit operations or one 8-bit operation and can

thus interface to 4-bit or 8-bit microcontrollers.

In 8-bit mode data is transferred as 8-bit bytes using the 8 data lines DB0 to DB7. Three

further control lines E, RS, and R/W are required.

In 4-bit mode data is transferred in two cycles of 4-bits each. The higher order bits

(corresponding to DB4 to DB7 in 8-bit mode) are sent in the first cycle and the lower order

bits (DB0 to DB3 in 8-bit mode) in the second.

Data transfer is complete after two 4-bit data transfers.

It should be noted that two cycles are also required for the Busy Flag check. 4-bit

operation is selected by instruction. See Figure 19, Figure 20 and Figure 21 for ex am p le s

of bus protocol.

In 4-bit mode pins DB3 to DB0 must be left open-circuit. They are pulled up to VDD

internally.

11. Interface to microcontroller (I2C-bus interface)

11.1 Characteristics of the I2C-bus

The I2C-bus is for bidirectional, two-line communication between different ICs or modules.

The two lines are a serial data line (SDA) and a serial clock line (SCL).

Both lines must be connected to a positive supply via a pull-up resistor . Data transfer may

be initiated only when the bus is not busy.

11.2 Bit transfe r

One data bit is transferred during each clock pulse.

The data on the SDA line must remain stable during the HIGH period of the clock pulse as

changes in the data line at this time will be interpreted as a control signal.

Product data sheet Rev. 05.01 — 20 July 2007 31 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

11.3 START and STOP conditions

Both data and clock lines remain HIGH when the bus is not busy. A HIGH-to-LOW

transition of the data line, while the clock is HIGH is defined as the START condition (S).

A LOW-to-HIGH transition of the data line while the clock is HIGH is defined as the STOP

condition (P).

11.4 System configuration

A device generating a message is a ‘transmitter’, a device receiving a message is the

‘receiver’. The device that controls the message is the ‘master’ and the devices which are

controlled by the master are the ‘slaves’.

11.5 Acknowledge

The number of data bytes transferred between the START and STOP conditions from

transmitter to receiver is unlimited. Each byte of eight bits is followed by an acknowledge

bit. The acknowledge bit is a HIGH level signal put on the bus by the transmitter during

which time the master generates an extra acknowledge related clock pulse. A slave

receiver which is addressed must generate an acknowledge after the reception of each

byte. Also a master receiver must generate an acknowledge after the reception of each

byte that has been clocked out of the slave transmitter. The device that acknowledges

must pull-down the SDA line during the acknowledge clock pulse, so that the SDA line is

stable LOW during the HIGH period of the acknowledge related clock pulse (set-up and

hold times must be taken into consideration). A master receiver must signal an end of data

to the transmitter by not generating an acknowledge on the last byte that has been

clocked out of the slave. In this event the transmitter must leave the data line HIGH to

enable the master to generate a STOP condition.

11.6 I2C-bus protocol

Before any data is transmitted on the I2C-bus, the device which should respond is

addressed first. The addressing is always carried out with the first byte transmitted after

the start procedure. The I2C-bus configuration for the different PCF2116 READ and

WRITE cycles is shown in Figure 22, Figure 23 and Figure 24.

Product data sheet Rev. 05.01 — 20 July 2007 32 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

Fig 22. Master transmits to slave receiver; WRITE mode

S011101 0A

slave address

CONTROL BYTE A DATA A DATA A

R/W 2n ≥ 0 bytes

acknowledgement

from PCF2116

CONTROL BYTE A

mbh66

update

data point

n ≥ 0 bytes1 byte

011101 0

PCF2116

slave address

R/W

Fig 23. Master reads slave immediately after first byte; READ mode (RS previously

defined)

mga81

S1A DATA A 1P

SLAVE

ADDRESS DATA

acknowledgement

from PCF2116

no acknowledgement

from master

R/W n bytes last byte

update

data pointer

acknowledgement

from master

xxxxxxxx xxxxxxxxxxx xx xxxxxxxxxx xxxxxxxxxxx xxxxx xxxxxxx x x x xx xxxxxxxxxxx xxxxxxxxxxx xxxxxx xxxxxx xxxxxxxxxxxxx xx xx xxxxx

xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x

xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx

xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx

Product data sheet Rev. 05.01 — 20 July 2007 33 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

(1) Last data byte is a dummy byte (may be omitted).

Fig 24. Master reads after setting word address; write word address, set RS/RW; READ data

S011101 0A

slave address

CONTROL BYTE A

DATA A1 1 CONTROL A

R/W

Co 2 bytes2n ≥ 0 bytes

DATA(1) A

acknowledgement

from PCF2116

mga809

S1A DATA A 1P

SLAVE

ADDRESS DATA

acknowledgement

from PCF2116 no acknowledgement

from master

R/W n bytes last byte

update

data pointer

Fig 25. Bit transfer

mbc62

data line

stable;

data valid

change

of data

allowed

Product data sheet Rev. 05.01 — 20 July 2007 34 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

Fig 26. Definition of START and STOP conditions

Fig 27. System configuration

Fig 28. Acknowledgement on the I2C-bus

mbc622

CL P

STOP condition

START condition

mga807

SDA

MASTER

TRANSMITTER/

RECEIVER

MASTER

TRANSMITTER

SLAVE

TRANSMITTER/

RECEIVER

SLAVE

RECEIVER

MASTER

TRANSMITTER/

RECEIVER

mbc60

START

condition

9821

clock pulse for

acknowledgement

not acknowledge

acknowledge

data output

y transmitter

data output

by receiver

SCL from

master

Product data sheet Rev. 05.01 — 20 July 2007 35 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

12. Limiting values

12.1 ESD values

•ESD protection exceeds 5000 V HBM per JESD22-A114, 200 V MM per

JESD22- A 115 and 1000 V CDM per JESD22 -C101.

•Latch-up testing is done to JEDEC standard JESD78 which exceeds 100 mA.

13. Static characteristics

Table 10. Limiting values

In accordance with the Absolute Maximum Rating System (IEC 60134).

Symbol Parameter Conditions Min Max Unit

VDD supply voltage −0.5 8.0 V

VLCD LCD suppl y vol tage VDD −11 VDD V

VI input voltage on each o f the pins O SC, V0, RS, R/W,

E, and DB0 to DB7 VSS −0.5 VDD +0.5 V

VOoutput voltage on each of the pins R1 to R32,

C1 to C60 and VLCD

VLCD −0.5 VDD +0.5 V

IIinput current −10 +10 mA

IOoutput current −10 +10 mA

IDD supply curr ent −50 +50 mA

ISS ground supply current −50 +50 mA

ILCD LCD suppl y curre nt −50 +50 mA

Ptot total power dissipation - 400 mW

POoutput power - 100 mW

Tstg storage temperature −65 +150 °C

CAUTION

Static voltages across the liquid crystal display can build up when the LCD supply voltage

(VLCD) is on while the IC supply voltage (VDD) is off, or vice versa. This may cause unwanted

dis play artifacts. To avoid such artifacts, VLCD and VDD must be applied or removed together.

Table 11. Static characterist ics

VDD = 2.5 to 6.0 V; VSS = 0 V; VLCD = VDD

−

3.5 V to VDD

−

9.0 V; TAMB =

−

40 to +85

C; unless otherwise specified.

Symbol Parameter Conditions Min Typ Max Unit

Supplies

VDD supply voltage 2.5 - 6.0 V

VLCD LCD supply voltage VDD − 9- V

DD − 3.5 V

IDD supply current external VLCD [1]

IDD1 supply current 1 external VLCD [1] -200500μA

IDD2 supply current 2 VDD = 5 V; VOP = 9 V;

fOSC = 150 kHz;

Tamb = 25 °C

[1] -200300μA

PCF2116_family_05 © NXP B.V. 2007. All rights reserved.
Product data sheet Rev. 05.01 — 20 July 2007  36 of 56
NXP Semiconductors PCF2116 family
LCD controller / drivers
IDD3 supply current 3 VDD = 3 V; VOP = 5 V; 
fOSC = 150 kHz; 
Tamb = 25 °C
[1] -150200μA
IDD4 supply  current 4 internal VLCD [1] [2] 
[8] - 700 1100 μA
IDD5 supply current 5 VDD = 5 V; VOP = 9 V; 
fOSC = 150 kHz; 
Tamb = 25 °C
[1] [2] 
[8] -600900μA
IDD6 supply current 6 VDD = 3 V; VOP = 5 V; 
fOSC = 150 kHz; 
Tamb = 25 °C
[1] [2] 
[8] -500800μA
ILCD LCD supply current  [1] [7] -50100μA
VPOR power on reset supply voltage [3] -1.31.8V
Logic
VIL1 LOW-level input voltage  input voltage on pins E, RS, 
R/W, DB0 to DB7 and SA0 VSS -0.3 V
DD V
VIH1 HIGH-level input voltage  input voltage on pins E, RS , 
R/W, DB0 to DB7 and SA0 0.7 VDD -V
DD V
VIL(OSC)  LOW-level input voltage on pin 
OSC VSS -V
DD − 1.5 V
VIL(V0)  LOW-level input voltage on pin V0VSS -V
DD − 1.5 V
VIH(OSC)  HIGH-level input voltage on pin 
OSC  VDD − 
0.1 -V
DD V
VIH(V0)  HIGH-level input  voltage on pin V 0 V
DD − 
0.05 -V
DD V
IPU  pull-up current pull- up current on pins  
DB0 to DB7; VI=V
SS
0.04 0.15 1.0 μA
IOL(DB)  LOW-level output  current  low level output  current on p ins 
DB0 to DB7; VOL =0.4V; 
VDD =5V
1.6 - - mA
IOH(DB) HIGH-level output current high level output current on pins 
DB0 to DB7; VOL =0.4V; 
VDD =5V
−1.0 - - mA
IL1 leakage current  VI=V
DD or VSS;
leakage current on pins 
OSC, V0,E,RS, R/W, DB0 to 
DB7 and SA0
−1.0 - +1.0 μA
LCD outputs
Vtol2  output voltage variation  LCD supply voltage 
(VLCD) tolerance [2] −300 40 +300 mV
Vtol1  output voltage variation  bias voltage tolerance 
on each pin: R1 - R32 
and C1 to C60
[7] −300 40 +300 mV
RROW output  resistance output resistance on 
each pin: R1 - R32
[6] -1.53.0kΩ
Table 11. Static characterist ics …continued
VDD = 2.5 to 6.0 V; VSS = 0 V; VLCD = VDD 
−
 3.5 V to VDD 
−
 9.0 V; TAMB = 
−
40 to +85 
°
C; unless otherwise specified.
Symbol Parameter Conditions Min Typ Max Unit

Product data sheet Rev. 05.01 — 20 July 2007 37 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

[1] LCD outputs are open-circuit; inputs at VDD or VSS; V0=V

DD; bus inactive; internal or external clock with duty cycle 50% (IDD1 only).

[2] LCD outputs are open-circuit; LCD supply voltage generator is on; load current at VLCD = 20 μA.

[3] Resets all logic when VDD <VPOR.

[4] When the voltages are above or below the supply voltages VDD or VSS, an input current may flow; this current must not exceed

±0.5 mA.

[5] Tested on sample basis.

[6] Resistance of output terminals (R1 to R32 and C1 to C60) with load current = 150 μA; VOP =V

DD −VLCD = 9 V ; outputs measured one

at a time; (external VLCD).

[7] LCD outputs open-circuit; external VLCD.

[8] Maximum value occurs at 85 °C.

14. Dynamic characteristics

RCOL output resistance output resistance on

each pin: C1 - C60

[6] -3.06.0kΩ

I2C-bus

SDA, SCL

VIL2 LOW-level input voltage [4] VSS -0.3 V

DD V

VIH2 HIGH-level input voltage [4] 0.7 VDD -V

DD V

IL2 leakage current VI=V

DD or VSS;

leakage current on pins SDA

and SCL

−1.0 - +1.0 μA

Ciinput capacitance [5] --7 pF

IOL(SDA) LOW level output current on pin

SDA VOL = 0.4 V; VDD =5V 3 - - mA

Table 11. Static characterist ics …continued

VDD = 2.5 to 6.0 V; VSS = 0 V; VLCD = VDD

−

3.5 V to VDD

−

9.0 V; TAMB =

−

40 to +85

C; unless otherwise specified.

Symbol Parameter Conditions Min Typ Max Unit

Table 12. Dynamic chara cteri stics

VDD = 2.5 to 6.0 V; VSS = 0 V; VLCD = VDD

−

3.5 V to VDD

−

9.0 V; TAMB =

−

40 to +85

C; unless otherwise specified.

Symbol Parameter Conditions Min Typ Max Unit

fosc clock frequency external clock

frequency 90 150 225 kHz

fFR LCD frame frequency internal clock [1] 40 65 100 Hz

Timing characteristics: Parallel interface [1] [2]

Write operation (writing data from microcontroller to PCF2116)

TCY enab le cycle time 500 - - ns

PWEH enab le pu l se width 220 - - ns

tASU address set-up time 50 - - ns

tAH address hold time 25 - - ns

tDSW data set-up time 60 - - ns

tHD data hold time 25 - - ns

Read operation (reading data from PCF2116 to microcontroller)

TCY enab le cycle time 500 - - ns

PWEH enab le pu l se width 220 - - ns

Product data sheet Rev. 05.01 — 20 July 2007 38 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

[1] VDD =5V.

[2] All timing values are valid within the operating supply voltage and ambient temperature range and are referenced to VIL and VIH with an

input voltage swing of VSS to VDD.

tASU address set-up time 50 - - ns

tAH address hold time 25 - - ns

tDHD data delay time - - 150 ns

tHD data hold time 20 - 100 ns

Timing characteristics: I2C-bus [2]

fSCL SCL clock frequency - - 100 kHz

tSW tolerable spike pulse width on the I2C-bus - - 100 ns

tBUF bus free time between a STOP and

START 4.7 - - μs

tSU;STA set-up time for a repeated START

condition 4.7 - - μs

tHD;STA START condition hold time 4.0 - - μs

tLOW SCL LOW time 4.7 - - μs

tHIGH SCL HIGH time 4.0 - - μs

trrise time of both SDA and SCL signals - - 1.0 μs

tffall time of both SDA and SCL signals - - 0.3 μs

tSU;DAT data set-up time 250 - - ns

tHD;DAT data hold time 0.0 - - ns

tSU;STO set-up time for STOP condition 4.0 - - μs

Table 12. Dynamic chara cteri stics …continued

VDD = 2.5 to 6.0 V; VSS = 0 V; VLCD = VDD

−

3.5 V to VDD

−

9.0 V; TAMB =

−

40 to +85

C; unless otherwise specified.

Symbol Parameter Conditions Min Typ Max Unit

Fig 29. Parallel bus write operation sequence; writing data from microcontroller to

PCF2116

B0 to DB7

IH1

IL1

IH1

IL1

IH1

IL1

IH1

IL1

IH1

IL1

IH1

IL1

DSW

Valid Data

mla79

R/W

Product data sheet Rev. 05.01 — 20 July 2007 39 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

15. Application information

Fig 30. Parallel bus read operation sequence; reading data from PCF2116 to

microcontroller

R/W

B0 to DB7

VIH1

VIL1

VIH1

VIL1

VIH1

VIL1 VIH1 VIL1

VOL1

VOH1

IL1

Tcy

tDHR

PWEH tAH

tAH

tAS

VOL1

VOH1

tDDR

VIH1

mla79

Fig 31. Direct connection to 8-bit microcontroller, 8-bit bus

Fig 32. Direct connection to 8-bit microcontroller, 4-bit bus

mga81

PCF2116

DB0 to DB7

R/W

R1 to R32

C1 to C60 60

P20

P21

P22

P10 to P17

P80CL51 to

mga81

PCF2116

DB4 to DB7

R/W

R1 to R32

C1 to C60 60

P10

P11

P12

P14 to P17

P80CL51 to

Product data sheet Rev. 05.01 — 20 July 2007 40 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

Fig 33. Typical application using parallel interface

Fig 34. Application using I2C-bus interface

mga816

LCD

PCF2116

100 nF

DB0 to DB7 E RS R/W

2 x 24 CHARACTER

LCD DISPLAY

(SPLIT SCREEN)

C1 to C60 60 60

OSC

100

nF 100

kΩ

R7 to R16

R25 to R32

R1 to R8

R17 to R24

VLCD

VDD

VSS

PCF2116

VSS

VDD

100 nF

2 x 24 CHARACTER

LCD DISPLAY

(SPLIT SCREEN)

C1 to C60 60 60

OSC

100

nF 100

kΩ

100

kΩ

mga817_02

VLCD

VDD

VSS

PCF2116

VSS

VDD

100 nF

4 x 12 CHARACTER

LCD DISPLAY

C1 to C60 60

OSC

100

R1 to R16

R17 to R24

R1 to R16

SA0

VSS

VDD

VDD VDD

SCL SDA MICRO CONTROLLER

Product data sheet Rev. 05.01 — 20 July 2007 41 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

Fig 35. 2 × 24 display layout example (PCF2116x)

Fig 36. Chip-on-glass application

1 316191120

C1 15 31 45 45 31 15 1

C16 30 46 60 60 46 30 16

R8 to R1 R9 to R16

R32 to R25R17 to R24

PCF2116 colum

output numbers

PCF2116 colum

output numbers

LCD column

numbers

DISPLAY LAYOUT: ROWS

DISPLAY LAYOUT: COLUMNS

2 x 24 character display mga81

mga81

PCF2116

CHIP-ON-GLASS

4 LINE BY

12 CHARACTER

R16

R25

R32

2116

R9 C60

SCL

SDA VLCD

VDD

VSS

Product data sheet Rev. 05.01 — 20 July 2007 42 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

15.1 4-bit operation, 1-line display using internal reset

The program must set functions prior to 4-bit operation. Table 13 shows an example.

When power is turned on, 8-bit operation is automatically selected and the PCF2116

attempts to perform the first write as an 8-bit operation. Since nothing is connected to

DB0 to DB3, a rewrite is then required. However, since one operation is completed in two

accesses of 4-bit operation, a rewrite is required to set the functions (see Table 13 step 3).

So, DB4 to DB7 of the function set are written twice.

Fig 37. 4 × 12 display layout example (PCF2116)

C1 15 46 60

C16 45

R8 to R1 R9 to R16

R32 to R25R17 to R24

DISPLAY LAYOUT: ROWS

DISPLAY LAYOUT: COLUMNS

PCF2116 colum

output numbers

PCF2116 colum

output numbers

LCD column

numbers

mga81

13160

DOT MATRIX LCD

Product data sheet Rev. 05.01 — 20 July 2007 43 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

15.2 8-bit operation, 1-line display using internal reset

Table 14 shows an example of a 1-line display in 8-bit operation. The PCF2116 functions

must be set by the ‘Function set’ instruction prior to display. Since the display data RAM

can store data for 80 characters, the RAM can be used for advertising displays when

combined with display shift operation. Since the display shift operation changes the

display position only and DDRAM contents remain unchanged, display data entered first

can be displayed when the Return Home operation is performed.

15.3 8-bit operation, 2-line display

For a 2-line display, the cursor automatically moves from the first to the second line after

the 40th digit of the first line is written. So, if there are only 8 characters in the first line, the

DDRAM address must be set after the eighth character is completed (see Table 15). Note

that both lines of the display are always shifted together; data does not shift from one line

to the other.

15.4 I2C-bus operation, 1-line display

A control byte is required with most instructions (see Table 16).

15.5 Initializi ng by instruction

If the power supply conditions for correctly operating the internal reset circuit are not met,

the PCF2116 must be initialized by instruction. Table 17 and Table 18 show how this may

be performed for 8-bit and 4-bit operation.

Table 13. 4-bit operation, 1-line display example; using internal reset

Step Instruction Display Operation

1 power supply on (PCF2116 is

initialized by the internal reset circuit) Initialized. No display appears.

2 function set

RS R/W DB7 DB6 DB5 DB4 Set s to 4-bit opera tion. In this i nst ance opera tio n

is hand led as 8-bit s by in itializatio n and only th is

instruction completes with one write.

000010

3 function set

0 0 0 0 1 0 Set s t o 4-bit op eration , select s 1- line dis play and

VLCD = V0. 4-bi t op erati on st arts fr om thi s point

and resetting is needed.

000000

4 display on/off control

0 0 0 0 0 0 _ Turns on display and cursor. Entire display is

blank after initialization.

001110

5 en try mo de set

0 0 0 0 0 0 _ Sets mode to increment the address by 1 and to

shift the cursor to the right at the time of write to

the DD/CGRAM. Display is not shifted.

000110

6 write data to CGRAM/DDRAM

1 0 0 1 0 1 P_ Writes ‘P’. The DDRAM has already been

selecte d by initia lization at power-on. The c ursor

is incremented by 1 and shifted to the right.

100000

xxxxxxxx xxxxxxxxxxx xx xxxxxxxxxx xxxxxxxxxxx xxxxx xxxxxxx x x x xx xxxxxxxxxxx xxxxxxxxxxx xxxxxx xxxxxx xxxxxxxxxxxxx xx xx xxxxx

xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x

xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx

xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx

Product data sheet Rev. 05.01 — 20 July 2007 44 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

Table 14. 8-bit operation, 1-line display example; using internal reset (character set ‘A’)

Step Instruction Display Operation

1 power supply on (PCF2116 is initialized by the internal reset function) Initialized. No display appears.

2 function set

RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Sets to 8-bit operation, selects 1-line display and

VLCD = V0.

0000110000

3 display mode on/off contr ol Turns on di sp lay and cu rsor. Entire display is bla nk af te r

initialization.

0000001110−

4 entry mo de set Set s mode to incre ment the addre ss by 1 and to s hift the

cursor to the right at the time of the write to the

DD/CGRAM. Display is not shifted.

0000000110−

5 write data to CGRAM/DDRAM Writes ‘P’. The DDRAM has already been selected by

initiali zation at powe r-on. The cursor is in cremented by 1

and shifted to the right.

1001010000P_

6 write data to CGRAM/DDRAM

1001001000PH_ Writes ‘H’.

7 |

8 write data to CGRAM/DDRAM

1001010011PHILIPS_ Writes ‘S’.

9 entry mo de set

0000000111PHILIPS_ Sets mode for display shift at the time of write.

10 writ e data to CGRAM/DDRAM

1000100000PHILIPS_ Writes space.

11 write data to CGRAM/DDRAM

1001001101 PHILIPSM_ Writes ‘M’.

12 |

13 writ e data to CGRAM/DDRAM

1001001111MICROKO Writes ‘O’.

14 cursor or display shift

0000010000MICROKO Shifts only the cursor position to the left.

xxxxxxxx xxxxxxxxxxx xx xxxxxxxxxx xxxxxxxxxxx xxxxx xxxxxxx x x x xx xxxxxxxxxxx xxxxxxxxxxx xxxxxx xxxxxx xxxxxxxxxxxxx xx xx xxxxx

xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x

xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx

xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx

Product data sheet Rev. 05.01 — 20 July 2007 45 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

15 cursor or display shift

0000010000MICROKO Shifts only the cursor position to the left.

16 writ e data to CGRAM/DDRAM

1001000011ICROCO Writes ‘C’ correction. The display moves to the left.

17 cursor or display shift

0000011100MICROCO Shifts the display and cursor to the right.

Z18 cursor or display shift

0000010100MICROCO_ Shifts only the cursor to theright.

19 writ e data to CGRAM/DDRAM

1001001101ICROCOM_ Writes ‘M’.

20 |

21 Return Home

0000000010PHILIPS M Returns both display and cursor to the original position

(address 0).

Table 14. 8-bit operation, 1-line display example; using internal reset (character set ‘A’)

Step Instruction Display Operation

xxxxxxxx xxxxxxxxxxx xx xxxxxxxxxx xxxxxxxxxxx xxxxx xxxxxxx x x x xx xxxxxxxxxxx xxxxxxxxxxx xxxxxx xxxxxx xxxxxxxxxxxxx xx xx xxxxx

xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x

xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx

xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx

Product data sheet Rev. 05.01 — 20 July 2007 46 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

Table 15. 8-bit operation, 2-line display example; using internal reset

Step Instruction Display Operation

1 power supply on (PCF2116 is initialized by the internal reset function) Initialized. No display appears.

2 function set Set s to 8-bit operati on, se lects 2-li ne displa y and volt age

gener ator off.

RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0

0000111000

3 display on/off control Turns on di splay and cu rso r. Entire di sp lay is bla nk after

initialization.

−

0000001110

4 entry mo de set _Set s mode to incre ment the addre ss by 1 and to s hift the

cursor t o the right at the time of w rite t o the CG/D DRAM.

Display is not shifted.

0000000110

5 Write data to CGRAM/DDRAM P_ Writes ‘P’. The DDRAM has already been selected by

initiali zation at powe r-on. The cursor is in cremented by 1

and shifted to the right.

1001010000

6 |

7 write data to CGRAM/DDRAM PHILIPS_ Writes ‘S’.

1001010011

8 set DDRAM address PHILIPS Sets DDRAM address to posi tion the cursor at the head

of the 2nd line.

0011000000_

9 write data to CGRAM/ DDRAM PHILIPS Writes ‘M’.

1001001101M_

10 |

xxxxxxxx xxxxxxxxxxx xx xxxxxxxxxx xxxxxxxxxxx xxxxx xxxxxxx x x x xx xxxxxxxxxxx xxxxxxxxxxx xxxxxx xxxxxx xxxxxxxxxxxxx xx xx xxxxx

xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x

xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx

xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx

Product data sheet Rev. 05.01 — 20 July 2007 47 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

11 write data to CGRAM/ DDRAM PHILIPS Writes ‘O’.

1001001111MICROCO_

12 writ e data to CGRAM/ DDRAM PHILIPS Sets mode for display shift at the time of write.

0000000111MICROCO_

13 writ e data to CGRAM/ DDRAM PHILIPS Writes ‘M’. Display is shifted to the left. The first and

second lines shift together.

1001001101ICROCOM_

14 |

15 return Home PHILIPS Returns both display and cursor to the original position

(address 0).

0000000010MICROCOM

Table 15. 8-bit operation, 2-line display example; using internal reset

Step Instruction Display Operation

xxxxxxxx xxxxxxxxxxx xx xxxxxxxxxx xxxxxxxxxxx xxxxx xxxxxxx x x x xx xxxxxxxxxxx xxxxxxxxxxx xxxxxx xxxxxx xxxxxxxxxxxxx xx xx xxxxx

xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x

xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx

xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx

Product data sheet Rev. 05.01 — 20 July 2007 48 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

Table 16. Example of I2C-bus operation; 1-line display (using internal reset, assuming SA0 = VSS [1])

Step Instruction Display Operation

2C START Initialized. No display appears.

2 slave address for write During the acknowledge cycle SDA is pulled-down by the

PCF2116.

SA6 SA5 SA4 SA3 SA2 SA1 SA0 R/W Ack

011101001

3 send a control byte for function set Control byte sets RS and R/W for following data bytes.

Co RS R/W Ack

000XXXXX1

4 function set Selects 1-line display and VLCD = V0; SCL pulse during

acknowledge cycle starts execution of instruction.

DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Ack

001X00001

5 display on/off control Turns on display and cursor. Entire display shows character 20h

(blank in ASCII-like character sets).

DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Ack

000011101−

6 entry mode set Sets mode to incr ement the ad dress by 1 an d to s hif t the c ursor to

the right at the time of write to the DDRAM or CGRAM. Display is

not shifted.

DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Ack

000001101−

2C START −Fo r writing data to DDR AM, RS must be set to 1. Therefore a

control byte is needed.

8 slave address for write

SA6 SA5 SA4 SA3 SA2 SA1 SA0 R/W Ack

011101001−

9 send a control byte for write data

Co RS R/W Ack

010XXXXX1−

10 wri t e data to DDRAM Writes ‘P’. The DDRAM has been selected at power-up.

The cursor is incremented by 1 and shifted to the right.

DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Ack

010100001P_

11 write data to DDRAM Writes ‘H’.

DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Ack

010010001PH_

xxxxxxxx xxxxxxxxxxx xx xxxxxxxxxx xxxxxxxxxxx xxxxx xxxxxxx x x x xx xxxxxxxxxxx xxxxxxxxxxx xxxxxx xxxxxx xxxxxxxxxxxxx xx xx xxxxx

xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x

xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx

xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx

Product data sheet Rev. 05.01 — 20 July 2007 49 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

[1] X = don’t care.

12 to 15 |

16 write data to DDRAM Writes ‘S’.

DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Ack

010100111PHILIPS_

17 (optional I2C stop) I2C start + slave ad dress for write (as step 8) PHILIPS_

18 control byte

Co RS R/W Ack

100XXXXX1PHILIPS_

19 Return Ho me Sets DDRAM address 0 in Address Counter. (also returns shifted

display to original position. DDRAM contents unchanged). This

instruction does not update the Data Register (DR).

DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Ack

000000101P

HILIPS

20 control byte for read DDRAM content will be read from following instructions.

The R/W has to be set to 1 while still in I2C-write mode

Co RS R/W Ack

011XXXXX1P

HILIPS

21 I2C START PHILIPS

22 slave addre ss for read During the ac knowledge cycle the content of the DR is loaded into

the internal I2C interface to be shifted out. In the previous

instructi on nei ther a ‘Set addres s’ nor a ‘Read data’ has been

performed. Therefore the content of the DR was unknown.

SA6 SA5 SA4 SA3 SA2 SA1 SA0 R/W Ack

011101011PH

ILIPS

23 read data: 8 × SCL + master acknowledge [2] 8×SCL; con tent loaded into interface du ring previous

acknowledge cycle is shifted out over SDA. MSB is DB7. During

master acknowledge content o f DDRAM address 01 is loaded into

the I2C inter face.

DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Ack

XXXXXXXX0PHI

LIPS

24 read data: 8 × SCL + master acknowledge [2] 8×SCL; code of letter ‘H’ is read first. During master

acknowledge code of ‘I’ is loaded into the I2C interface.

DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Ack

010010000PHILIPS

25 read data: 8 × SCL + no master acknowledge [2] No master acknowledge; After the content of the I2C interface

is loaded to the interface register, Data Register (DR) is not

updated, Address Counter (AC) is not incremented and cursor is

not shifted.

DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Ack

010010011PHIL

IPS

26 I2C stop PHILIPS

Table 16. Example of I2C-bus operation; 1-line display (using internal reset, assuming SA0 = VSS [1])

Step Instruction Display Operation

xxxxxxxx xxxxxxxxxxx xx xxxxxxxxxx xxxxxxxxxxx xxxxx xxxxxxx x x x xx xxxxxxxxxxx xxxxxxxxxxx xxxxxx xxxxxx xxxxxxxxxxxxx xx xx xxxxx

xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x

xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx

xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx

Product data sheet Rev. 05.01 — 20 July 2007 50 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

[2] SDA is left at high-impedance by the microcontroller during the READ acknowledge.

[1] X = don’t care.

Table 17. Initialization by instruction, 8 bit interfac e [1]

Step Description

power-on or unknown state

wait 2 ms after VDD rises above VPOR

RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 BF cannot be checked before this instruction

000011××××Function set (interface is 8 bits long)

wait 2 ms

RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 BF cannot be checked before this instruction

000011××××Function set (interface is 8 bits long)

wait more than 40 μs

RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 BF cannot be checked before this instruction

000011××××Function set (interface is 8 bits long)

BF can be checked after the following instructions. When the BF is not

checked the waiting t ime between instructions is the specified instructio n time

(see Table 8).

RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Function set (interface is 8 bits long). Specify the number of display lines and

voltage generator characteristics.

000011NMG0

0000001000Display off.

0000000001Clear display.

00000001I/DSEntry mode set.

Initialization ends

xxxxxxxx xxxxxxxxxxx xx xxxxxxxxxx xxxxxxxxxxx xxxxx xxxxxxx x x x xx xxxxxxxxxxx xxxxxxxxxxx xxxxxx xxxxxx xxxxxxxxxxxxx xx xx xxxxx

xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x

xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx

xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx

Product data sheet Rev. 05.01 — 20 July 2007 51 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

Table 18. Initialization by instruction, 4 bit interface. Not applicable for I2C-bus operation.

Step Description

power-on or unknown state

wait 2 ms after VDD rises above VPOR

RS R/W DB7 DB6 DB5 DB4 BF cannot be checked before this instruction

000011Function set (interface is 8 bits long)

wait 2 ms

RS R/W DB7 DB6 DB5 DB4 BF cannot be checked before this instruction

000011Function set (interface is 8 bits long)

wait more than 40 μs

RS R/W DB7 DB6 DB5 DB4 BF cannot be checked before this instruction

000011Function set (interface is 8 bits long)

BF can be checked after the following instructions. When the BF is not checked the waiting time

between instructions is the specified instruction time (see Table 8).

RS R/W DB7 DB6 DB5 DB4 Function set (set interface to 4 bits long).

000011Interface is 8 bits long

000010Function set (interface is 4 bits long).

0 0 N M G 0 Specify the number of display lines and voltage generator characteristics.

000000

001000Display off.

000000Clear display.

000001

000000Entry mode set.

0001I/DS

Initialization ends

Product data sheet Rev. 05.01 — 20 July 2007 52 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

16. Package outline

Not applicab le .

17. Handling information

Inputs and outputs are protected against electrostatic discharge in normal handling.

However , to be completely safe you must take normal precautions appropriate to handling

MOS devices; see JESD625-A and/or IEC61340-5.

18. Packing information

Table 19. Tray dim ensions (see Figure 38)

Symbol Description Value

A pocket pitch in x direction 5.64 mm

B pocket pitch in y direction 5.64 mm

C pocket width in x direction 4.08 mm

D pocket width in y direction 4.08 mm

E tray width in x direction 50.8 mm

F tray width in y direction 50.8 mm

G cut corner to pocket 1.1 centre 5.66 mm

H cut corner to pocket 1.1 centre 5.66 mm

x number of poc kets, x directi on 8

y number of poc kets, y directi on 8

Fig 38. Tray details

001aag783

1,1 x,12,1

1,2

1,y x,y

Product data sheet Rev. 05.01 — 20 July 2007 53 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

Fig 39. Tray alignment

001aag782

PC2116-1

Product data sheet Rev. 05.01 — 20 July 2007 54 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

19. Revision history

Table 20. Revision history

Document ID Release date Data sheet status Change notice Supersedes

PCF2116_FAM_5.01 <tbd> Product data sheet 20070711 (date) PCF2116_FAM_4

Modifications: •Character set ‘A’ in CGROM corrected, Section 8.2.

•Packing information added, Section 18

•The format of this data sheet has been redesigned to comply with the new identity

guidelines of NXP Semiconductors.

•Legal texts have been adapted to the new company name where appropriate.

PCF2116_FAM_4 19970407 Product data sheet PCF2116_3

PCF2116_3 19961025 Product data sheet PCF2116_2

PCF2116_2 19941010 Product data sheet PCF2116A_1

PCF2116A_1 19931215 Product data sheet -

Product data sheet Rev. 05.01 — 20 July 2007 55 of 56

NXP Semiconductors PCF2116 family

LCD controller / drivers

20. Legal information

20.1 Data sheet status

[1] Please consult the most recently issued document before initiating or completing a design.

[2] The term ‘short data sheet’ is explained in section “Definitions”.

[3] The product statu s of device(s) described in this document may have changed since this document was published and may dif fer in ca se of mu ltiple d evices. T he latest pro duct sta tus

information is available on the Internet at URL http://www.nxp.com.

20.2 Definitions

Draft — The document is a draft version only. The content is still under

internal review and subject to formal approval, which may result in

modifications or additions. NXP Se miconductors does not give any

representations or warranties as to the accuracy or completeness of

information included herein and shall have no liability for the consequences of

use of such information.

Short data sheet — A short data sheet is an extract from a full data sheet

with the same product type number(s) and title. A short data sheet is intended

for quick reference only and should not be relied upon to contain detailed and

full information. For detailed and full information see the relevant full data

shee t, which is availa bl e on req ues t via the local NX P Semico nd ucto rs sales

office. In case of any inconsistency or conflict with the short data sheet, the

full data sheet shall prevail.

20.3 Disclaimers

General — Information in this document is believed to be accurate and

reliable. However, NXP Semiconductors does not give any representations or

warranties, expressed or implied, as to the accuracy or completeness of such

information and shall have no liability for the consequences of use of such

information.

Right to make changes — NXP Semiconductors reserves the right to make

changes to information published in this document, including without

limitation specifications and product descriptions, at any time and without

notice. This document supersedes and replaces all information supplied prior

to the publication hereof.

Suitability for use — NXP Semiconductors products are not designed,

authorized or warranted to be suitable for use in medical, military, aircraft,

space or life support equipment , nor in applicati ons where failure or

malfunction of a NXP Semiconductors product can reasonably be expected to

result in personal injury, death or severe property or environmental damage.

NXP Semiconductors accepts no liability for inclusion and/or use of NXP

Semiconductors products in such equipment or applications and therefore

such inclusion and/or use is at the customer’s own risk.

Applications — Applications that are described herein for any of these

products are for illustrative purposes only. NXP Semiconductors makes no

representation or warranty that such applications will be suitable for the

specified use without further testing or modification.

Limit ing values — Stress above one or more limiting values (as defined in

the Absolute Maximum Ratings System of IEC 60134) may cause permanent

damage to the device. Limiting values are stress ratings only and operation of

the device at these or any other conditions above those given in the

Characteristics sections of this document is not implied. Exposure to limiting

values for extended periods may affect device reliability.

Terms and conditions of sale — NXP Semiconductors products are sold

subject to the general terms and conditions of commercial sale, as published

at http://www.nxp.com/profile/terms, including those pertaining to warranty,

intellectual property rights infringement and limitation of liability, unless

explicitly otherwise agreed to in writing by NXP Semiconductors. In case of

any inconsistency or conflict between information in this document and such

terms and conditions, the latter will prevail.

No offer to sell or license — Nothing in this document may be interpreted or

construed as an offer to sell products that is open for acceptance or the grant,

conveyance or implication of any license under any copyrights, patents or

other industrial or intellectual property rights.

20.4 Trademarks

Notice: All referenced brands, product names, service names and trademarks

are the property of their respective owners.

I2C-bus — logo is a trademark of NXP B.V.

21. Contact inf ormat ion

For additional information, please visit: http://www.nxp.com

For sales office addresses, send an email to: salesaddresses@nxp.com

Document status[1][2] Product status[3] Definition

Objective [short] data sheet Development This document contains data from the objective specification for product development.

Preliminary [short] data sheet Qualification This document contains data from the preliminary specification.

Product [short] data sheet Production This document contains the product specification.

NXP Semiconductors PCF2116 family

LCD controller / drivers

For more information, please visit: http://www.nxp.com

For sales office addresses, please send an email to: salesaddresses@nxp.com

Date of release: 20 July 2007

Document identifier: PCF2116_family_05

Please be aware that important notices concerning this document and the product(s)

described herein , have been included in section ‘Legal informati on’.

22. Contents

1 General description. . . . . . . . . . . . . . . . . . . . . . 1

2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

3 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

4 Ordering information. . . . . . . . . . . . . . . . . . . . . 2

5 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 3

6 Pinning information. . . . . . . . . . . . . . . . . . . . . . 4

6.1 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

6.2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 5

7 Pin functions . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

7.1 RS: register select (parallel control) . . . . . . . . . 8

7.2 R/W: read/write (parallel control) . . . . . . . . . . . 8

7.3 E: data bus clock . . . . . . . . . . . . . . . . . . . . . . . 8

7.4 DB0 to DB7: data bus. . . . . . . . . . . . . . . . . . . . 9

7.5 C1 to C60: column driver outputs. . . . . . . . . . . 9

7.6 R1 to R32: row driver outputs. . . . . . . . . . . . . . 9

7.7 VLCD: LCD power supply . . . . . . . . . . . . . . . . . 9

7.8 V0: VLCD control input . . . . . . . . . . . . . . . . . . . . 9

7.9 O SC: oscillator . . . . . . . . . . . . . . . . . . . . . . . . . 9

7.10 SCL: serial clock line . . . . . . . . . . . . . . . . . . . . 9

7.11 SDA: serial data line. . . . . . . . . . . . . . . . . . . . . 9

7.12 SA0: address pin . . . . . . . . . . . . . . . . . . . . . . . 9

7.13 T1: test pad. . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

8 Functional description . . . . . . . . . . . . . . . . . . . 9

8.1 LCD supply voltage generator for PCF2116x. . 9

8.2 Character generator ROM (CGROM). . . . . . . 11

8.3 LCD bias voltage generator . . . . . . . . . . . . . . 15

8.4 O scillator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

8.5 External clock. . . . . . . . . . . . . . . . . . . . . . . . . 15

8.6 Power-on reset . . . . . . . . . . . . . . . . . . . . . . . . 15

8.7 Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

8.8 Busy flag. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

8.9 Address counter (AC). . . . . . . . . . . . . . . . . . . 16

8.10 Display data RAM (DDRAM) . . . . . . . . . . . . . 16

8.11 Character generator RAM (CGRAM) . . . . . . . 18

8.12 Cursor control circuit. . . . . . . . . . . . . . . . . . . . 18

8.13 Timing generator. . . . . . . . . . . . . . . . . . . . . . . 19

8.14 LCD row and column drivers . . . . . . . . . . . . . 19

8.15 Reset function. . . . . . . . . . . . . . . . . . . . . . . . . 22

9 Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

9.1 Clear display. . . . . . . . . . . . . . . . . . . . . . . . . . 27

9.2 Return home. . . . . . . . . . . . . . . . . . . . . . . . . . 27

9.3 Entry mode set . . . . . . . . . . . . . . . . . . . . . . . . 27

9.3.1 I/D. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

9.3.2 S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

9.4 Display on/off control . . . . . . . . . . . . . . . . . . . 28

9.4.1 D. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

9.4.2 C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

9.4.3 B. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

9.5 Cursor display shift . . . . . . . . . . . . . . . . . . . . 28

9.6 Function set . . . . . . . . . . . . . . . . . . . . . . . . . . 28

9.6.1 DL (parallel mode only) . . . . . . . . . . . . . . . . . 28

9.6.2 N, M . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

9.6.3 G . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

9.7 Set CGRAM address . . . . . . . . . . . . . . . . . . . 29

9.8 Set DDRAM address . . . . . . . . . . . . . . . . . . . 29

9.9 Read busy flag and address . . . . . . . . . . . . . 29

9.10 Write data to CGRAM or DDRAM . . . . . . . . . 29

9.11 Read data from CGRAM or DDRAM . . . . . . . 29

10 Interface to microcontroller (parallel

interface) . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

11 Interface to microcontroller (I2C-bus

interface) . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

11.1 Characteristics of the I2C-bus . . . . . . . . . . . . 30

11.2 Bit transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

11.3 START and STOP conditions. . . . . . . . . . . . . 31

11.4 System configuration . . . . . . . . . . . . . . . . . . . 31

11.5 Acknowledge . . . . . . . . . . . . . . . . . . . . . . . . . 31

11.6 I2C-bus protocol. . . . . . . . . . . . . . . . . . . . . . . 31

12 Limiting values . . . . . . . . . . . . . . . . . . . . . . . . 35

12.1 ESD values . . . . . . . . . . . . . . . . . . . . . . . . . . 35

13 Static characteristics . . . . . . . . . . . . . . . . . . . 35

14 Dynamic characteristics. . . . . . . . . . . . . . . . . 37

15 Application information . . . . . . . . . . . . . . . . . 39

15.1 4-bit operation, 1-line display using internal reset

15.2 8-bit operation, 1-line display using internal reset

15.3 8-bit operation, 2-line display. . . . . . . . . . . . . 43

15.4 I2C-bus operation, 1-line display . . . . . . . . . . 43

15.5 Initializing by instruction. . . . . . . . . . . . . . . . . 43

16 Package outline. . . . . . . . . . . . . . . . . . . . . . . . 52

17 Handling information . . . . . . . . . . . . . . . . . . . 52

18 Packing information . . . . . . . . . . . . . . . . . . . . 52

19 Revision history . . . . . . . . . . . . . . . . . . . . . . . 54

20 Legal information . . . . . . . . . . . . . . . . . . . . . . 55

20.1 Data sheet status. . . . . . . . . . . . . . . . . . . . . . 55

20.2 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

20.3 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . 55

20.4 Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . 55

21 Contact information . . . . . . . . . . . . . . . . . . . . 55

22 Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56