M29W128GH70N6E - MICRON TECHNOLOGY

Parallel NOR Flash Embedded Memory

M29W128GH, M29W128GL

Features

• Supply voltage

– VCC = 2.7–3.6V (program, erase, read)

– VCCQ = 1.65–3.6V (I/O buffers)

– VPPH = 12V for fast program (optional)

• Asynchronous random/page read

– Page size: 8 words or 16 bytes

– Page access: 25, 30ns

– Random access: 60ns1, 70, 80ns

• Fast program commands: 32-word (64-byte) write

buffer

• Enhanced buffered program commands: 256-word

• Program time

– 16µs per byte/word TYP

– Chip program time: 5s with VPPH and 8s without

VPPH

• Memory organization

– Uniform blocks: 128 main blocks, 128-Kbytes or

64-Kwords each

• Program/erase controller

– Embedded byte/word program algorithms

• Program/erase suspend and resume capability

– Read from any block during a PROGRAM SUS-

PEND operation

– Read or program another block during an ERASE

SUSPEND operation

• Unlock bypass, block erase, chip erase, write to buf-

fer, enhanced buffer program commands

– Fast buffered/batch programming

– Fast block/chip erase

• VPP/WP# pin protection

– Protects first or last block regardless of block

protection settings

• Software protection

– Volatile protection

– Nonvolatile protection

– Password protection

• Extended memory block

– 128-word (256-byte) memory block for perma-

nent, secure identification

• Common flash interface

– 64-bit security code

• Low power consumption: Standby and automatic

mode

• Minimum 100,00 PROGRAM/ERASE cycles per

block

• RoHS compliant packages

– 56-pin TSOP (N) 14mm x 20mm

– 64-ball TBGA (ZA) 10mm x 13mm

– 64-ball FBGA (ZS) 11mm x 13mm

• Electronic signature

– Manufacturer code: 0020h

– M29W128GH uniform, last block protected by

VPP/WP#: 227Eh + 2221h + 2201h

– M29W128GL uniform, first block protected by

VPP/WP#: 227Eh + 2221h + 2200h

• Automotive device grade temperature

– –40°C to +125°C (automotive grade certified)

Note: 1. The 60ns device is available upon customer

request.

128Mb 3V Embedded Parallel NOR Flash

Features

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 1Micron Technology, Inc. reserves the right to change products or specifications without notice.

Products and specifications discussed herein are subject to change by Micron without notice.

Part Numbering Information

Available with extended memory block prelocked by Micron. Devices are shipped from the factory with memory

content bits erased to 1. For available options, such as packages or high/low protection, or for further information,

contact your Micron sales representative. Part numbers can be verified at www.micron.com. Feature and specifica-

tion comparison by device type is available at www.micron.com/products. Contact the factory for devices not

found.

Table 1: Part Number Information

Part Number

Category Category Details Notes

Device type M29

Operating voltage W = VCC = 2.7– 3.6V

Device function 128GH = 128Mb (x8/x16) page, uniform block Flash memory, highest block protected by

VPP/WP#

128GL = 128Mb (x8/x16) page, uniform block Flash memory, lowest block protected by

VPP/WP#

Speed 70 = 70ns 1

60 = 60ns 1, 2

7A = 70ns 1, 3

Package N = 56-pin TSOP, 14mm x 20mm

ZA = 64-ball TBGA, 10mm x 13mm, 1mm pitch

ZS = 64-ball Fortified BGA, 11mm x 13mm, 1mm pitch

Temperature range 1 = 0 to 70°C

6 = –40°C to +85°C (IT)

3 = –40°C to +125°C (IT)

Shipping options E = RoHS-compliant package, standard packing

F = RoHS-compliant package, tape and reel packing

Notes: 1. 80ns if VCCQ = 1.65V to VCC.

2. The 60ns device is available upon customer request.

3. Automotive qualified, available only with option 6. Qualified and characterized according to AEC Q100 and

Q003 or equivalent; advanced screening according to AEC Q001 and Q002 or equivalent.

128Mb 3V Embedded Parallel NOR Flash

Features

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 2Micron Technology, Inc. reserves the right to change products or specifications without notice.

Contents

Important Notes and Warnings ......................................................................................................................... 7

General Description ......................................................................................................................................... 7

Signal Assignments ........................................................................................................................................... 9

Signal Descriptions ......................................................................................................................................... 11

Memory Organization .................................................................................................................................... 12

Uniform Block Memory Map – 128Mb Density ............................................................................................. 12

Bus Operations ............................................................................................................................................... 13

Read .......................................................................................................................................................... 13

Write .......................................................................................................................................................... 13

Standby and Automatic Standby ................................................................................................................. 13

Output Disable ........................................................................................................................................... 14

Reset .......................................................................................................................................................... 14

Status Register ................................................................................................................................................ 15

Lock Register .................................................................................................................................................. 20

Standard Command Definitions – Address-Data Cycles .................................................................................... 23

READ Operations ........................................................................................................................................... 25

READ/RESET Command ............................................................................................................................ 25

READ CFI Command .................................................................................................................................. 25

AUTO SELECT Operations .............................................................................................................................. 26

AUTO SELECT Command ........................................................................................................................... 26

Bypass Operations .......................................................................................................................................... 29

UNLOCK BYPASS Command ...................................................................................................................... 29

UNLOCK BYPASS RESET Command ............................................................................................................ 29

Program Operations ....................................................................................................................................... 30

PROGRAM Command ................................................................................................................................ 30

UNLOCK BYPASS PROGRAM Command ..................................................................................................... 30

WRITE TO BUFFER PROGRAM Command .................................................................................................. 30

UNLOCK BYPASS WRITE TO BUFFER PROGRAM Command ....................................................................... 33

WRITE TO BUFFER PROGRAM CONFIRM Command .................................................................................. 33

BUFFERED PROGRAM ABORT AND RESET Command ................................................................................ 33

PROGRAM SUSPEND Command ................................................................................................................ 33

PROGRAM RESUME Command .................................................................................................................. 34

ENHANCED BUFFERED PROGRAM Command ........................................................................................... 34

UNLOCK BYPASS ENHANCED BUFFERED PROGRAM Command ............................................................... 35

ENHANCED BUFFERED PROGRAM CONFIRM Command .......................................................................... 35

Erase Operations ............................................................................................................................................ 38

CHIP ERASE Command .............................................................................................................................. 38

UNLOCK BYPASS CHIP ERASE Command ................................................................................................... 38

BLOCK ERASE Command ........................................................................................................................... 38

UNLOCK BYPASS BLOCK ERASE Command ................................................................................................ 39

ERASE SUSPEND Command ....................................................................................................................... 39

ERASE RESUME Command ........................................................................................................................ 40

Block Protection Command Definitions – Address-Data Cycles ........................................................................ 41

Protection Operations .................................................................................................................................... 44

LOCK REGISTER Commands ...................................................................................................................... 44

PASSWORD PROTECTION Commands ....................................................................................................... 44

NONVOLATILE PROTECTION Commands .................................................................................................. 44

NONVOLATILE PROTECTION BIT LOCK BIT Commands ............................................................................ 46

VOLATILE PROTECTION Commands .......................................................................................................... 46

EXTENDED MEMORY BLOCK Commands .................................................................................................. 46

128Mb 3V Embedded Parallel NOR Flash

Features

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 3Micron Technology, Inc. reserves the right to change products or specifications without notice.

EXIT PROTECTION Command .................................................................................................................... 47

Device Protection ........................................................................................................................................... 48

Hardware Protection .................................................................................................................................. 48

Software Protection .................................................................................................................................... 48

Volatile Protection Mode ............................................................................................................................. 49

Nonvolatile Protection Mode ...................................................................................................................... 49

Password Protection Mode .......................................................................................................................... 50

Common Flash Interface ................................................................................................................................ 51

Power-Up and Reset Characteristics ................................................................................................................ 55

Absolute Ratings and Operating Conditions ..................................................................................................... 58

DC Characteristics .......................................................................................................................................... 60

Read AC Characteristics .................................................................................................................................. 62

Write AC Characteristics ................................................................................................................................. 65

Accelerated Program, Data Polling/Toggle AC Characteristics ........................................................................... 72

Program/Erase Characteristics ........................................................................................................................ 74

Package Dimensions ....................................................................................................................................... 75

Revision History ............................................................................................................................................. 78

Rev. C – 05/18 ............................................................................................................................................. 78

Rev. B – 05/15 ............................................................................................................................................. 78

Rev. A – 07/13 ............................................................................................................................................. 78

128Mb 3V Embedded Parallel NOR Flash

Features

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 4Micron Technology, Inc. reserves the right to change products or specifications without notice.

List of Figures

Figure 1: 128 Logic Diagram ............................................................................................................................ 8

Figure 2: 56-Pin TSOP (Top View) .................................................................................................................... 9

Figure 3: 64-Ball Fortified BGA and 64-Ball TBGA ........................................................................................... 10

Figure 4: Data Polling Flowchart .................................................................................................................... 17

Figure 5: Toggle Bit Flowchart ........................................................................................................................ 18

Figure 6: Status Register Polling Flowchart ..................................................................................................... 19

Figure 7: Lock Register Program Flowchart ..................................................................................................... 21

Figure 8: WRITE TO BUFFER PROGRAM Flowchart ........................................................................................ 32

Figure 9: ENHANCED BUFFERED PROGRAM Flowchart ................................................................................ 36

Figure 10: Program/Erase Nonvolatile Protection Bit Algorithm ...................................................................... 45

Figure 11: Software Protection Scheme .......................................................................................................... 50

Figure 12: Power-Up Timing .......................................................................................................................... 55

Figure 13: Reset AC Timing – No PROGRAM/ERASE Operation in Progress ...................................................... 56

Figure 14: Reset AC Timing During PROGRAM/ERASE Operation .................................................................... 57

Figure 15: AC Measurement Load Circuit ....................................................................................................... 59

Figure 16: AC Measurement I/O Waveform ..................................................................................................... 59

Figure 17: Random Read AC Timing (8-Bit Mode) ........................................................................................... 63

Figure 18: Random Read AC Timing (16-Bit Mode) ......................................................................................... 63

Figure 19: BYTE Transition AC Timing ............................................................................................................ 64

Figure 20: Page Read AC Timing (16-Bit Mode) ............................................................................................... 64

Figure 21: WE#-Controlled Program AC Timing (8-Bit Mode) .......................................................................... 66

Figure 22: WE#-Controlled Program AC Timing (16-Bit Mode) ......................................................................... 67

Figure 23: CE#-Controlled Program AC Timing (8-Bit Mode) ........................................................................... 69

Figure 24: CE#-Controlled Program AC Timing (16-Bit Mode) ......................................................................... 70

Figure 25: Chip/Block Erase AC Timing (8-Bit Mode) ...................................................................................... 71

Figure 26: Accelerated Program AC Timing ..................................................................................................... 72

Figure 27: Data Polling AC Timing .................................................................................................................. 73

Figure 28: Toggle/Alternative Toggle Bit Polling AC Timing (8-Bit Mode) .......................................................... 73

Figure 29: 56-Pin TSOP – 14mm x 20mm ........................................................................................................ 75

Figure 30: 64-Ball TBGA – 10mm x 13mm ....................................................................................................... 76

Figure 31: 64-Ball FBGA – 11mm x 13mm ....................................................................................................... 77

128Mb 3V Embedded Parallel NOR Flash

Features

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 5Micron Technology, Inc. reserves the right to change products or specifications without notice.

List of Tables

Table 1: Part Number Information ................................................................................................................... 2

Table 2: Signal Descriptions ........................................................................................................................... 11

Table 3: x8 and x16 Blocks[127:0] ................................................................................................................... 12

Table 4: Bus Operations ................................................................................................................................. 13

Table 5: Status Register Bit Definitions ........................................................................................................... 15

Table 6: Operations and Corresponding Bit Settings ........................................................................................ 16

Table 7: Lock Register Bit Definitions ............................................................................................................. 20

Table 8: Block Protection Status ..................................................................................................................... 20

Table 9: Standard Command Definitions – Address-Data Cycles, 8-Bit and 16-Bit ............................................. 23

Table 10: Read Electronic Signature ............................................................................................................... 26

Table 11: Block Protection ............................................................................................................................. 28

Table 12: Block Protection Command Definitions – Address-Data Cycles, 8-Bit and 16-Bit ................................ 41

Table 13: Extended Memory Block Address and Data ...................................................................................... 46

Table 14: VPP/WP# Functions ......................................................................................................................... 48

Table 15: Query Structure Overview ............................................................................................................... 51

Table 16: CFI Query Identification String ........................................................................................................ 51

Table 17: CFI Query System Interface Information .......................................................................................... 52

Table 18: Device Geometry Definition ............................................................................................................ 52

Table 19: Primary Algorithm-Specific Extended Query Table ........................................................................... 53

Table 20: Security Code Area .......................................................................................................................... 54

Table 21: Power-Up Wait Timing Specifications .............................................................................................. 55

Table 22: Reset AC Characteristics .................................................................................................................. 56

Table 23: Absolute Maximum/Minimum Ratings ............................................................................................ 58

Table 24: Operating and AC Measurment Conditions ...................................................................................... 58

Table 25: Input/Output Capacitance .............................................................................................................. 59

Table 26: DC Current Characteristics .............................................................................................................. 60

Table 27: DC Voltage Characteristics .............................................................................................................. 61

Table 28: Read AC Characteristics .................................................................................................................. 62

Table 29: WE#-Controlled Write AC Characteristics ......................................................................................... 65

Table 30: CE#-Controlled Write AC Characteristics ......................................................................................... 68

Table 31: Accelerated Program and Data Polling/Data Toggle AC Characteristics .............................................. 72

Table 32: Program/Erase Characteristics ........................................................................................................ 74

128Mb 3V Embedded Parallel NOR Flash

Features

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 6Micron Technology, Inc. reserves the right to change products or specifications without notice.

Important Notes and Warnings

Micron Technology, Inc. ("Micron") reserves the right to make changes to information published in this document,

including without limitation specifications and product descriptions. This document supersedes and replaces all

information supplied prior to the publication hereof. You may not rely on any information set forth in this docu-

ment if you obtain the product described herein from any unauthorized distributor or other source not authorized

by Micron.

Automotive Applications. Products are not designed or intended for use in automotive applications unless specifi-

cally designated by Micron as automotive-grade by their respective data sheets. Distributor and customer/distrib-

utor shall assume the sole risk and liability for and shall indemnify and hold Micron harmless against all claims,

costs, damages, and expenses and reasonable attorneys' fees arising out of, directly or indirectly, any claim of

product liability, personal injury, death, or property damage resulting directly or indirectly from any use of non-

automotive-grade products in automotive applications. Customer/distributor shall ensure that the terms and con-

ditions of sale between customer/distributor and any customer of distributor/customer (1) state that Micron

products are not designed or intended for use in automotive applications unless specifically designated by Micron

as automotive-grade by their respective data sheets and (2) require such customer of distributor/customer to in-

demnify and hold Micron harmless against all claims, costs, damages, and expenses and reasonable attorneys'

fees arising out of, directly or indirectly, any claim of product liability, personal injury, death, or property damage

resulting from any use of non-automotive-grade products in automotive applications.

Critical Applications. Products are not authorized for use in applications in which failure of the Micron compo-

nent could result, directly or indirectly in death, personal injury, or severe property or environmental damage

("Critical Applications"). Customer must protect against death, personal injury, and severe property and environ-

mental damage by incorporating safety design measures into customer's applications to ensure that failure of the

Micron component will not result in such harms. Should customer or distributor purchase, use, or sell any Micron

component for any critical application, customer and distributor shall indemnify and hold harmless Micron and

its subsidiaries, subcontractors, and affiliates and the directors, officers, and employees of each against all claims,

costs, damages, and expenses and reasonable attorneys' fees arising out of, directly or indirectly, any claim of

product liability, personal injury, or death arising in any way out of such critical application, whether or not Mi-

cron or its subsidiaries, subcontractors, or affiliates were negligent in the design, manufacture, or warning of the

Micron product.

Customer Responsibility. Customers are responsible for the design, manufacture, and operation of their systems,

applications, and products using Micron products. ALL SEMICONDUCTOR PRODUCTS HAVE INHERENT FAIL-

URE RATES AND LIMITED USEFUL LIVES. IT IS THE CUSTOMER'S SOLE RESPONSIBILITY TO DETERMINE

WHETHER THE MICRON PRODUCT IS SUITABLE AND FIT FOR THE CUSTOMER'S SYSTEM, APPLICATION, OR

PRODUCT. Customers must ensure that adequate design, manufacturing, and operating safeguards are included

in customer's applications and products to eliminate the risk that personal injury, death, or severe property or en-

vironmental damages will result from failure of any semiconductor component.

Limited Warranty. In no event shall Micron be liable for any indirect, incidental, punitive, special or consequential

damages (including without limitation lost profits, lost savings, business interruption, costs related to the removal

or replacement of any products or rework charges) whether or not such damages are based on tort, warranty,

breach of contract or other legal theory, unless explicitly stated in a written agreement executed by Micron's duly

authorized representative.

General Description

The M29W is an asynchronous, uniform block, parallel NOR Flash memory device man-

ufactured on 90nm single-level cell (SLC) technology. READ, ERASE, and PROGRAM op-

erations are performed using a single low-voltage supply. Upon power-up, the device

defaults to read array mode.

128Mb 3V Embedded Parallel NOR Flash

Important Notes and Warnings

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 7Micron Technology, Inc. reserves the right to change products or specifications without notice.

The main memory array is divided into uniform blocks that can be erased independent-

ly so that valid data can be preserved while old data is purged. PROGRAM and ERASE

commands are written to the command interface of the memory. An on-chip program/

erase controller simplifies the process of programming or erasing the memory by taking

care of all special operations required to update the memory contents. The end of a

PROGRAM or ERASE operation can be detected and any error condition can be identi-

fied. The command set required to control the device is consistent with JEDEC stand-

ards.

CE#, OE#, and WE# control the bus operation of the device and enable a simple con-

nection to most microprocessors, often without additional logic.

The M29W supports asynchronous random read and page read from all blocks of the

array. It features a write to buffer program capability that improves throughput by pro-

gramming a buffer of 32 words in one command sequence. Also, in x16 mode, the en-

hanced buffered program capability improves throughput by programming 256 words

in one command sequence. The device VPP/WP# signal enables faster programming.

The device contains a 128-word (x16) and 256-byte (x8) extended memory block. The

user can program this additional space and then protect it to permanently secure the

contents. The device also features different levels of hardware and software protection

to secure blocks from unwanted modification.

Figure 1: 128 Logic Diagram

VCC VCCQ

A[22:0]

WE#

VPP/WP#

DQ[14:0]

DQ15/A-1

VSS

CE#

OE#

RST#

BYTE#

RY/BY#

128Mb 3V Embedded Parallel NOR Flash

General Description

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 8Micron Technology, Inc. reserves the right to change products or specifications without notice.

Signal Assignments

Figure 2: 56-Pin TSOP (Top View)

RFU

A22

A15

A14

A13

A12

A11

A10

A19

A20

WE#

RST#

A21

VPP/WP#

RY/BY#

A18

A17

RFU

A16

BYTE#

VSS

DQ15/A-1

DQ7

DQ14

DQ6

DQ13

DQ5

DQ12

DQ4

VCC

DQ11

DQ3

DQ10

DQ2

DQ9

DQ1

DQ8

DQ0

OE#

VSS

CE#

RFU

VCCQ

Notes: 1. A22 = A[MAX].

2. A-1 is the least significant address bit in x8 mode.

128Mb 3V Embedded Parallel NOR Flash

Signal Assignments

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 9Micron Technology, Inc. reserves the right to change products or specifications without notice.

Figure 3: 64-Ball Fortified BGA and 64-Ball TBGA

RFU

VCCQ

RFU

VCCQ

RFU

CE#

OE#

VSS

CE#

OE#

VSS

A17

RY/BY#

VPP/WP#

A18

A20

D10

D11

RY/BY#

VPP/WP#

A18

A20

D10

D11

WE#

RST#

A21

A19

D12

VCC

WE#

RST#

A21

A19

D12

VCC

A10

A11

D14

D13

A10

A11

D14

D13

A13

A12

A14

A15

A16

BYTE#

D15/A-1

VSS

A13

A12

A14

A15

A16

BYTE#

D15/A-1

VSS

RFU

A22

RFU

VCCQ

VSS

RFU

A22

RFU

VCCQ

VSS

RFU

Top view – ball side down Bottom view – ball side up

Notes: 1. A[22] = A[MAX].

2. A-1 is the least significant address bit in x8 mode.

128Mb 3V Embedded Parallel NOR Flash

Signal Assignments

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 10 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Signal Descriptions

The signal description table below is a comprehensive list of signals for this device fami-

ly. All signals listed may not be supported on this device. See Signal Assignments for in-

formation specific to this device.

Table 2: Signal Descriptions

Name Type Description

A[MAX:0] Input Address: Selects the cells in the array to access during READ operations. During WRITE oper-

ations, they control the commands sent to the command interface of the program/erase con-

troller.

CE# Input Chip enable: Activates the device, enabling READ and WRITE operations to be performed.

When CE# is HIGH, the device goes to standby and data outputs are at HIGH-Z.

OE# Input Output enable: Controls the bus READ operation.

WE# Input Write enable: Controls the bus WRITE operation of the command interface.

VPP/WP# Input VPP/Write Protect: Provides WRITE PROTECT function and VPPH function. These functions

protect the lowest or highest block and enable the device to enter unlock bypass mode, re-

spectively. (Refer to Hardware Protection and Bypass Operations for details.)

BYTE# Input Byte/word organization select: Switches between x8 and x16 bus modes. When BYTE# is

LOW, the device is in x8 mode; when HIGH, the device is in x16 mode.

RST# Input Reset: Applies a hardware reset to the device, which is achieved by holding RST# LOW for at

least tPLPX. After RST# goes HIGH, the device is ready for READ and WRITE operations (after

tPHEL or tRHEL, whichever occurs last). See RESET AC Specifications for more details.

DQ[7:0] I/O Data I/O: Outputs the data stored at the selected address during a READ operation. During

WRITE operations, they represent the commands sent to the command interface of the inter-

nal state machine.

DQ[14:8] I/O Data I/O: Outputs the data stored at the selected address during a READ operation when

BYTE# is HIGH. When BYTE# is LOW, these pins are not used and are High-Z. During WRITE

operations, these bits are not used. When reading the status register, these bits should be ig-

nored.

DQ15/A-1 I/O Data I/O or address input: When the device operates in x16 bus mode, this pin behaves as

data I/O, together with DQ[14:8]. When the device operates in x8 bus mode, this pin behaves

as the least significant bit of the address.

Except where stated explicitly otherwise, DQ15 = data I/O (x16 mode); A-1 = address input (x8

mode).

RY/BY# Output Ready busy: Open-drain output that can be used to identify when the device is performing

a PROGRAM or ERASE operation. During PROGRAM or ERASE operations, RY/BY# is LOW,

and is High-Z during read mode, auto select mode, and erase suspend mode. After a hard-

ware reset, READ and WRITE operations cannot begin until RY/BY# goes High-Z (see RESET

AC Specifications for more details).

The use of an open-drain output enables the RY/BY# pins from several devices to be connec-

ted to a single pull-up resistor to VCCQ. A low value will then indicate that one (

or more) of the devices is (are) busy. A 10K Ohm or bigger resistor is recommended as pull-up

resistor to achieve 0.1V VOL.

128Mb 3V Embedded Parallel NOR Flash

Signal Descriptions

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 11 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 2: Signal Descriptions (Continued)

Name Type Description

VCC Supply Supply voltage: Provides the power supply for READ, PROGRAM, and ERASE operations.

The command interface is disabled when VCC <= VLKO. This prevents WRITE operations from

accidentally damaging the data during power-up, power-down, and power surges. If the pro-

gram/erase controller is programming or erasing during this time, then the operation aborts

and the contents being altered will be invalid.

A 0.1μF capacitor should be connected between VCC and VSS to decouple the current surges

from the power supply. The PCB track widths must be sufficient to carry the currents required

during PROGRAM and ERASE operations (see DC Characteristics).

VCCQ Supply I/O supply voltage: Provides the power supply to the I/O pins and enables all outputs to be

powered independently from VCC.

VSS Supply Ground: All VSS pins must be connected to the system ground.

RFU – Reserved for future use: RFUs should be not connected.

Memory Organization

Uniform Block Memory Map – 128Mb Density

Table 3: x8 and x16 Blocks[127:0]

Block

Size

Address Range (x8) Block

Size

Address Range (x16)

Start End Start End

127 128KB 0FE 0000h 0FF FFFFh 64KW 07F 0000h 07F FFFFh

⋮ ⋮ ⋮ ⋮ ⋮

63 07E 0000h 07F FFFFh 03F 0000h 03F FFFFh

⋮ ⋮ ⋮ ⋮ ⋮

0 000 0000h 001 FFFFh 000 0000h 000 FFFFh

Note: 1. The main memory array is divided into 128KB or 64KW uniform blocks.

128Mb 3V Embedded Parallel NOR Flash

Memory Organization

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 12 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Bus Operations

Table 4: Bus Operations

Notes 1 and 2 apply to entire table

Operation CE# OE# WE# RST# VPP/WP#

8-Bit Mode 16-Bit Mode

A[MAX:0],

DQ15/A-1 DQ[14:8] DQ[7:0] A[MAX:0]

DQ15/A-1,

DQ[14:0]

READ L L H H X Cell address High-Z Data output Cell address Data output

WRITE L H L H X3Command

address

High-Z Data input4Command

address

Data input4

STANDBY H X X H X X High-Z High-Z X High-Z

OUTPUT

DISABLE

L H H H X X High-Z High-Z X High-Z

RESET X X X L X X High-Z High-Z X High-Z

Notes: 1. Typical glitches of less than 5ns on CE#, WE#, and RST# are ignored by the device and do

not affect bus operations.

2. H = Logic level HIGH (VIH); L = Logic level LOW (VIL); X = HIGH or LOW.

3. If WP# is LOW, then the highest or the lowest block remains protected, depending on

line item.

4. Data input is required when issuing a command sequence or when performing data

polling or block protection.

Read

Bus READ operations read from the memory cells, registers, or CFI space. To accelerate

the READ operation, the memory array can be read in page mode where data is inter-

nally read and stored in a page buffer.

The page size is 8 words (16 bytes) and is addressed by address inputs A[2:0] in x16 bus

mode and A[2:0] plus DQ15/A-1 in x8 bus mode. The extended memory blocks and CFI

area do not support page read mode.

A valid READ operation requires setting the appropriate address on the address inputs,

taking CE# and OE# LOW, and holding WE# HIGH. Data I/O signals output the value.

Write

Bus WRITE operations write to the command interface. A valid WRITE operation re-

quires setting the appropriate address on the address inputs. These are latched by the

command interface on the falling edge of CE# or WE#, whichever occurs last. Values on

data I/O signals are latched by the command interface on the rising edge of CE# or

WE#, whichever occurs first. OE# must remain HIGH during the entire operation.

Standby and Automatic Standby

When the device is in read mode, driving CE# HIGH places the device in standby mode

and drives data I/Os to High-Z. Supply current is reduced to standby (ICC2) by holding

CE# within VCC ±0.3V.

128Mb 3V Embedded Parallel NOR Flash

Bus Operations

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 13 Micron Technology, Inc. reserves the right to change products or specifications without notice.

During PROGRAM or ERASE operations, the device continues to use the program/erase

supply current (ICC3) until the operation completes.

Automatic standby enables low power consumption during read mode. When CMOS

levels (VCC ± 0.3 V) drive the bus, and following a READ operation and a period of inac-

tivity specified in DC Characteristics, the memory enters automatic standby as internal

supply current is reduced to ICC2. Data I/O signals still output data if a READ operation

is in progress. Depending on load circuits connected with data bus, VCCQ can have a

null consumption when the memory enters automatic standby.

Output Disable

Data I/Os are High-Z when OE# is HIGH.

Reset

During reset mode, the device is deselected, and outputs are High-Z. The device is in

reset mode when RST# is LOW. Power consumption is reduced to standby level inde-

pendently from CE#, OE#, or WE# inputs.

128Mb 3V Embedded Parallel NOR Flash

Bus Operations

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 14 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Status Register

Table 5: Status Register Bit Definitions

Note 1 applies to entire table

Bit Name Settings Description Notes

DQ7 Data polling

bit

0 or 1, depending on

operations

Monitors whether the program/erase controller has successful-

ly completed its operation, or has responded to an ERASE SUS-

PEND operation.

2, 3, 4

DQ6 Toggle bit Toggles: 0 to 1; 1 to 0;

and so on

Monitors whether the program/erase controller has successful-

ly completed its operations, or has responded to an ERASE

SUSPEND operation. During a PROGRAM/ERASE operation,

DQ6 toggles from 0 to 1, 1 to 0, and so on, with each succes-

sive READ operation from any address.

3, 4, 5

DQ5 Error bit 0 = Success

1 = Failure

Identifies errors detected by the program/erase controller. DQ5

is set to 1 when a PROGRAM, BLOCK ERASE, or CHIP ERASE op-

eration fails to write the correct data to the memory.

4, 6

DQ3 Erase timer

bit

0 = Erase not in progress

1 = Erase in progress

Identifies the start of program/erase controller operation dur-

ing a BLOCK ERASE command. Before the program/erase con-

troller starts, this bit set to 0, and additional blocks to be

erased can be written to the command interface.

DQ2 Alternative

toggle bit

Toggles: 0 to 1; 1 to 0;

and so on

Monitors the program/erase controller during ERASE opera-

tions. During CHIP ERASE, BLOCK ERASE, and ERASE SUSPEND

operations, DQ2 toggles from 0 to 1, 1 to 0, and so on, with

each successive READ operation from addresses within the

blocks being erased.

3, 4

DQ1 Buffered

program

abort bit

1 = Abort Indicates a BUFFER PROGRAM operation abort. The BUFFERED

PROGRAM ABORT and RESET command must be issued to re-

turn the device to read mode (see WRITE TO BUFFER PRO-

GRAM command).

Notes: 1. The status register can be read during PROGRAM, ERASE, or ERASE SUSPEND operations;

the READ operation outputs data on DQ[7:0].

2. For a PROGRAM operation in progress, DQ7 outputs the complement of the bit being

programmed. For a READ operation from the address previously programmed success-

fully, DQ7 outputs existing DQ7 data. For a READ operation from addresses with blocks

to be erased while an ERASE SUSPEND operation is in progress, DQ7 outputs 0; upon

successful completion of the ERASE SUSPEND operation, DQ7 outputs 1. For an ERASE

operation in progress, DQ7 outputs 0; upon either operation's successful completion,

DQ7 outputs 1.

3. After successful completion of a PROGRAM or ERASE operation, the device returns to

read mode.

4. During erase suspend mode, READ operations to addresses within blocks not being

erased output memory array data as if in read mode. A protected block is treated the

same as a block not being erased. See the Toggle Flowchart for more information.

5. During erase suspend mode, DQ6 toggles when addressing a cell within a block being

erased. The toggling stops when the program/erase controller has suspended the ERASE

operation. See the Toggle Flowchart for more information.

6. When DQ5 is set to 1, a READ/RESET command must be issued before any subsequent

command.

128Mb 3V Embedded Parallel NOR Flash

Status Register

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 15 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 6: Operations and Corresponding Bit Settings

Note 1 applies to entire table

Operation Address DQ7 DQ6 DQ5 DQ3 DQ2 DQ1 RY/BY# Notes

PROGRAM Any address DQ7# Toggle 0 – No toggle 0 0 2

PROGRAM during

ERASE SUSPEND

Any address DQ7# Toggle 0 – – – 0

BUFFERED

PROGRAM ABORT

Any address DQ7# Toggle 0 – – 1 0 2

PROGRAM error Any address DQ7# Toggle 1 – – – High-Z

CHIP ERASE Any address 0 Toggle 0 1 Toggle – 0

BLOCK ERASE

before time-out

Erasing block 0 Toggle 0 0 Toggle – 0

Non-erasing block 0 Toggle 0 0 No toggle – 0

BLOCK ERASE Erasing block 0 Toggle 0 1 Toggle – 0

Non-erasing block 0 Toggle 0 1 No toggle – 0

ERASE SUSPEND Erasing block 1 No toggle 0 – Toggle – High-Z

Non-erasing block Outputs memory array data as if in read mode – High-Z

BLOCK ERASE

error

Good block

address

0 Toggle 1 1 No toggle – High-Z

Faulty block

address

0 Toggle 1 1 Toggle – High-Z

Notes: 1. Unspecified data bits should be ignored.

2. DQ7# for buffer program is related to the last address location loaded.

128Mb 3V Embedded Parallel NOR Flash

Status Register

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 16 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Figure 4: Data Polling Flowchart

Start

DQ7 = Data

DQ5 = 1

DQ1 = 1

DQ7 = Data

Yes

Read DQ7, DQ5, and DQ1

at valid address1

Read DQ7 at valid address

SuccessFailure 2

Notes: 1. Valid address is the address being programmed or an address within the block being

erased.

2. Failure results: DQ5 = 1 indicates an operation error; DQ1 = 1 indicates a WRITE TO BUF-

FER PROGRAM ABORT operation.

128Mb 3V Embedded Parallel NOR Flash

Status Register

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 17 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Figure 5: Toggle Bit Flowchart

DQ6 = Toggle

DQ5 = 1

DQ6 = Toggle

Yes

Start

Read DQ6 at valid address

Read DQ6, DQ5, and DQ1

at valid address

Read DQ6 (twice) at valid address

SuccessFailure1

DQ1 = 1

Yes

Note: 1. Failure results: DQ5 = 1 indicates an operation error; DQ1 = 1 indicates a WRITE TO BUF-

FER PROGRAM ABORT operation.

128Mb 3V Embedded Parallel NOR Flash

Status Register

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 18 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Figure 6: Status Register Polling Flowchart

WRITE TO BUFFER

PROGRAM

Start

DQ7 = Valid data

DQ5 = 1

Yes

DQ6 = Toggling Yes

No No

Yes

PROGRAM operation

DQ6 = Toggling

DQ2 = Toggling

Yes

DQ1 = 1

Read 3 correct data?

Yes

Device busy: Repolling

PROGRAM operation

complete

PROGRAM operation

failure

WRITE TO BUFFER

PROGRAM

abort

Timeout failure

ERASE operation

complete

Erase/suspend mode

Device error

Read2.DQ6 = Read3.DQ6

Read2.DQ2 = Read3.DQ2

Read1.DQ6 = Read2.DQ6

128Mb 3V Embedded Parallel NOR Flash

Status Register

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 19 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Lock Register

Table 7: Lock Register Bit Definitions

Note 1 applies to entire table

Bit Name Settings Description Notes

DQ2 Password

protection

mode lock bit

0 = Password protection

mode enabled

1 = Password protection

mode disabled (Default)

Places the device permanently in password protection mode. 2

DQ1 Nonvolatile

protection

mode lock bit

0 = Nonvolatile protection

mode enabled with pass-

word protection mode

permanently disabled

1 = Nonvolatile protection

mode enabled (Default)

Places the device in nonvolatile protection mode with pass-

word protection mode permanently disabled. When shipped

from the factory, the device will operate in nonvolatile protec-

tion mode, and the memory blocks are unprotected.

DQ0 Extended

memory

block

protection bit

0 = Protected

1 = Unprotected (Default)

If the device is shipped with the extended memory block un-

locked, the block can be protected by setting this bit to 0. The

extended memory block protection status can be read in auto

select mode by issuing an AUTO SELECT command.

Notes: 1. The lock register is a 16-bit, one-time programmable register. DQ[15:3] are reserved and

are set to a default value of 1.

2. The password protection mode lock bit and nonvolatile protection mode lock bit cannot

both be programmed to 0. Any attempt to program one while the other is programmed

causes the operation to abort, and the device returns to read mode. The device is ship-

ped from the factory with the default setting.

Table 8: Block Protection Status

Nonvolatile

Protection Bit

Lock Bit1

Nonvolatile

Protection

Bit2

Volatile

Protection

Bit3

Block

Protection

Status Block Protection Status

1 1 1 00h Block unprotected; nonvolatile protection bit changeable.

1 1 0 01h Block protected by volatile protection bit; nonvolatile protec-

tion bit changeable.

1 0 1 01h Block protected by nonvolatile protection bit; nonvolatile

protection bit changeable.

1 0 0 01h Block protected by nonvolatile protection bit and volatile

protection bit; nonvolatile protection bit changeable.

0 1 1 00h Block unprotected; nonvolatile protection bit unchangeable.

0 1 0 01h Block protected by volatile protection bit; nonvolatile protec-

tion bit unchangeable.

0 0 1 01h Block protected by nonvolatile protection bit; nonvolatile

protection bit unchangeable.

128Mb 3V Embedded Parallel NOR Flash

Lock Register

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 20 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 8: Block Protection Status (Continued)

Nonvolatile

Protection Bit

Lock Bit1

Nonvolatile

Protection

Bit2

Volatile

Protection

Bit3

Block

Protection

Status Block Protection Status

0 0 0 01h Block protected by nonvolatile protection bit and volatile

protection bit; nonvolatile protection bit unchangeable.

Notes: 1. Nonvolatile protection bit lock bit: when cleared to 1, all nonvolatile protection bits are

unlocked; when set to 0, all nonvolatile protection bits are locked.

2. Block nonvolatile protection bit: when cleared to 1, the block is unprotected; when set

to 0, the block is protected.

3. Block volatile protection bit: when cleared to 1, the block is unprotected; when set to 0,

the block is protected.

Figure 7: Lock Register Program Flowchart

Start

Done?

DQ5 = 1

Yes

Enter LOCK REGISTER command set

Address/data (unlock) cycle 1

Address/data (unlock) cycle 2

Address/data cycle 3

PROGRAM LOCK REGISTER

Address/data cycle 1

Address/data cycle 2

Polling algorithm

Success:

EXIT PROTECTION command set

(Returns to device read mode)

Address/data cycle 1

Address/data cycle 2

Failure:

READ/RESET

(Returns device to read mode)

Notes: 1. Each lock register bit can be programmed only once.

128Mb 3V Embedded Parallel NOR Flash

Lock Register

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 21 Micron Technology, Inc. reserves the right to change products or specifications without notice.

2. See the Block Protection Command Definitions table for address-data cycle details.

128Mb 3V Embedded Parallel NOR Flash

Lock Register

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 22 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Standard Command Definitions – Address-Data Cycles

Table 9: Standard Command Definitions – Address-Data Cycles, 8-Bit and 16-Bit

Note 1 applies to entire table

Command and

Code/Subcode

Bus

Size

Address and Data Cycles

Notes

1st 2nd 3rd 4th 5th 6th

A D A D A D A D A D A D

READ and AUTO SELECT Operations

READ/RESET (F0h) x8 X F0

AAA AA 555 55 X F0

x16 X F0

555 AA 2AA 55 X F0

READ CFI (98h) x8 AA 98

x16 55

AUTO SELECT (90h) x8 AAA AA 555 55 AAA 90 Note

Note

2, 3, 4

x16 555 2AA 555

BYPASS Operations

UNLOCK BYPASS (20h) x8 AAA AA 555 55 AAA 20

x16 555 2AA 555

UNLOCK BYPASS

RESET (90h/00h)

x8 X 90 X 00

x16

PROGRAM Operations

PROGRAM (A0h) x8 AAA AA 555 55 AAA A0 PA PD

x16 555 2AA 555

UNLOCK BYPASS

PROGRAM (A0h)

x8 X A0 PA PD 5

x16

WRITE TO BUFFER

PROGRAM (25h)

x8 AAA AA 555 55 BAd 25 BAd N PA PD 6, 7, 8

x16 555 2AA

UNLOCK BYPASS

WRITE TO BUFFER

PROGRAM (25h)

x8 BAd 25 BAd N PA PD 5

x16

WRITE TO BUFFER

PROGRAM CONFIRM

(29h)

x8 BAd 29

x16

BUFFERED PROGRAM

ABORT and RESET (F0h)

x8 AAA AA 555 55 AAA F0

x16 555 2AA 555

ENHANCED

BUFFERED

PROGRAM (33h)

x8 NA 9

x16 555 AA 2AA 55 555 33 BAd

(00)

Data

UNLOCK BYPASS

ENHANCED

BUFFERED PROGRAM

(33h)

x8 NA 10

x16 BAd 33 BAd

(00)

Data BAd

(01)

Data

128Mb 3V Embedded Parallel NOR Flash

Standard Command Definitions – Address-Data Cycles

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 23 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 9: Standard Command Definitions – Address-Data Cycles, 8-Bit and 16-Bit (Continued)

Note 1 applies to entire table

Command and

Code/Subcode

Bus

Size

Address and Data Cycles

Notes

1st 2nd 3rd 4th 5th 6th

A D A D A D A D A D A D

ENHANCED

BUFFERED

PROGRAM CONFIRM

(29h)

x8 NA

x16 BAd

(00)

ENHANCED

BUFFERED

PROGRAM ABORT (F0h)

x8 NA

x16 555 AA 2AA 55 555 F0

PROGRAM SUSPEND

(B0h)

x8 X B0

x16

PROGRAM RESUME

(30h)

x8 X 30

x16

ERASE Operations

CHIP ERASE (80/10h) x8 AAA AA 555 55 AAA 80 AAA AA 555 55 AAA 10

x16 555 2AA 555 555 2AA 555

UNLOCK BYPASS

CHIP ERASE (80/10h)

x8 X 80 X 10 5

x16

BLOCK ERASE (80/30h) x8 AAA AA 555 55 AAA 80 AAA AA 555 55 BAd 30 11

x16 555 2AA 555 555 2AA

UNLOCK BYPASS

BLOCK ERASE (80/30h)

x8 X 80 BAd 30 5

x16

ERASE SUSPEND (B0h) x8 X B0

x16

ERASE RESUME (30h) x8 X 30

x16

Notes: 1. A = Address; D = Data; X = "Don't Care"; BAd = Any address in the block; N = Number of

bytes to be programmed; PA = Program address; PD = Program data; Gray shading = Not

applicable. All values in the table are hexadecimal. Some commands require both a com-

mand code and subcode.

2. These cells represent READ cycles (versus WRITE cycles for the others).

3. AUTO SELECT enables the device to read the manufacturer code, device code, block pro-

tection status, and extended memory block protection indicator.

4. AUTO SELECT addresses and data are specified in the Electronic Signature table and the

Extended Memory Block Protection table.

5. For any UNLOCK BYPASS ERASE/PROGRAM command, the first two UNLOCK cycles are

unnecessary.

6. BAd must be the same as the address loaded during the WRITE TO BUFFER PROGRAM

3rd and 4th cycles.

7. WRITE TO BUFFER PROGRAM operation: maximum cycles = 68(x8) and 36 (x16). UNLOCK

BYPASS WRITE TO BUFFER PROGRAM operation: maximum cycles = 66 (x8), 34 (x16).

128Mb 3V Embedded Parallel NOR Flash

Standard Command Definitions – Address-Data Cycles

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 24 Micron Technology, Inc. reserves the right to change products or specifications without notice.

WRITE TO BUFFER PROGRAM operation: N + 1 = bytes to be programmed; maximum

buffer size = 64 bytes (x8) and 32 words (x16).

8. For x8, A[MAX:5] address pins should remain unchanged while A[4:0] and A-1 pins are

used to select a byte within the N + 1 byte page. For x16, A[MAX:5] address pins should

remain unchanged while A[4:0] pins are used to select a word within the N + 1 word

page.

9. The following is content for address-data cycles 258 through 259: BAd (FE) - Data; BAd

(FF) - Data.

10. The following is content for address-data cycles 256 through 257: BAd (FE) - Data; BAd

(FF) - Data.

11. BLOCK ERASE address cycles can extend beyond six address-data cycles, depending on

the number of blocks to erase.

READ Operations

READ/RESET Command

The READ/RESET (F0h) command returns the device to read mode and resets the errors

in the status register. One or three bus WRITE operations can be used to issue the

READ/RESET command.

To return the device to read mode, this command can be issued between bus WRITE

cycles before the start of a PROGRAM or ERASE operation. If the READ/RESET com-

mand is issued during the timeout of a BLOCK ERASE operation, the device requires up

to 10μs to abort, during which time no valid data can be read.

READ CFI Command

The READ CFI (98h) command puts the device in read CFI mode and is valid only when

the device is in read array or auto select mode. One bus WRITE cycle is required to issue

the command.

Once in read CFI mode, bus READ operations will output data from the CFI memory

area. A READ/RESET command must be issued to return the device to the previous

mode (read array or auto select ). A second READ/RESET command is required to put

the device in read array mode from auto select mode.

128Mb 3V Embedded Parallel NOR Flash

READ Operations

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 25 Micron Technology, Inc. reserves the right to change products or specifications without notice.

AUTO SELECT Operations

AUTO SELECT Command

At power-up or after a hardware reset, the device is in read mode. It can then be put in

auto select mode by issuing an AUTO SELECT (90h) command or by applying VID to A9.

Auto select mode enables the following device information to be read:

• Electronic signature, which includes manufacturer and device code information, as

shown in the Electronic Signature table.

• Block protection, which includes the block protection status and extended memory

block protection indicator, as shown in the Block Protection table.

Electronic signature or block protection information is read by executing a READ opera-

tion with control signals and addresses set, as shown in the Read Electronic Signature

table or the Block Protection table, respectively.

Auto select mode can be used by the programming equipment to automatically match a

device with the application code to be programmed.

Three consecutive bus WRITE operations are required to issue an AUTO SELECT com-

mand. The device remains in auto select mode until a READ/RESET or READ CFI com-

mand is issued.

The device cannot enter auto select mode when a PROGRAM or ERASE operation is in

progress (RY/BY# LOW). However, auto select mode can be entered if the PROGRAM or

ERASE operation has been suspended by issuing a PROGRAM SUSPEND or ERASE SUS-

PEND command.

To enter auto select mode by appling VID to A9, see the Read Electronic Signature table

and the Block Protection table.

Auto select mode is exited by performing a reset. The device returns to read mode un-

less it entered auto select mode after an ERASE SUSPEND or PROGRAM SUSPEND

command, in which case it returns to erase or program suspend mode.

Table 10: Read Electronic Signature

Note 1 applies to entire table

Signal

READ Cycle

Notes

Manufacturer

Code Device Code 1 Device Code 3 Device Code 3

CE# L L L L

OE# L L L L

WE# H H H H

Address Input, 8-Bit and 16-Bit

A[MAX:10] X X X X

A9 VID VID VID VID 2

A8 X X X X

A[7:5] L L L L

A4 X X X X

A[3:1] L L H H

128Mb 3V Embedded Parallel NOR Flash

AUTO SELECT Operations

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 26 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 10: Read Electronic Signature (Continued)

Note 1 applies to entire table

Signal

READ Cycle

Notes

Manufacturer

Code Device Code 1 Device Code 3 Device Code 3

A0 L H L H

Address Input, 8-Bit Only

DQ[15]/A-1 X X X X

Data I/O, 8-Bit Only

DQ[14:8] X X X X

DQ[7:0] 20h 7Eh 21h XX

Data I/O, 16-Bit Only

DQ[15]/A-1, and DQ[14:0] 0020h 227Eh 2221h XXXX

Notes: 1. H = Logic level HIGH (VIH); L = Logic level LOW (VIL); X = HIGH or LOW.

2. When using the AUTO SELECT command to enter auto select mode, applying VID to A9 is

not required. A9 can be either VIL or VIH.

3. XX = 01h for M29W128GH and 00h for M29W128GL.

4. XXXX = 2201h for M29W128GH and 2200h for M29W128GL.

128Mb 3V Embedded Parallel NOR Flash

AUTO SELECT Operations

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 27 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 11: Block Protection

Note 1 applies to entire table

Signal

READ Cycle

Notes

Extended Memory

Block

Verify Indicator (GL)

Extended Memory

Block

Verify Indicator (GH)

Block Protection

Status Indicator

CE# L L L

OE# L L L

WE# H H H

Address Input, 8-Bit and 16-Bit

A[MAX:16] X X Block base address

A[15:10] X X X

A9 VID VID VID 2

A8 X X X

A[7:5] L L L

A4 X X X

A[3:2] L L L

A1 H H H

A0 H H L

Address Input, 8-Bit Only

DQ[15]/A-1 X X X

Data I/O, 8-Bit Only

DQ[14:8] X X X

DQ[7:0] 89h 99h 01h 3, 5

09h 19h 00h 4, 6

Data I/O, 16-Bit Only

DQ[15]/A-1, and DQ[14:0] 0089h 0099h 0001h 3, 5

0009h 0019h 0000h 4, 6

Notes: 1. Read cycle output to DQ7 = Extended memory block protection indicator; GH = High

block protection; GL = Low block protection; BPS = Block protection status; H = Logic

level HIGH (VIH); L = Logic level LOW (VIL); X = HIGH or LOW.

2. When using the AUTO SELECT command to enter auto select mode, applying VID to A9 is

not required. A9 can be either VIL or VIH.

3. Extended memory blocks are Micron-prelocked (permanent).

4. Extended memory blocks are customer-lockable.

5. Block protection status = protected: 01h (in x8 mode) is output on DQ[7:0].

6. Block protection status = unprotected: 00h (in x8 mode) is output on DQ[7:0].

128Mb 3V Embedded Parallel NOR Flash

AUTO SELECT Operations

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 28 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Bypass Operations

UNLOCK BYPASS Command

The UNLOCK BYPASS (20h) command is used to place the device in unlock bypass

mode. Three bus WRITE operations are required to issue the UNLOCK BYPASS com-

mand.

When the device enters unlock bypass mode, the two initial UNLOCK cycles required

for a standard PROGRAM or ERASE operation are not needed, thus enabling faster total

program or erase time.

The UNLOCK BYPASS command is used in conjunction with UNLOCK BYPASS PRO-

GRAM or UNLOCK BYPASS ERASE commands to program or erase the device faster

than with standard PROGRAM or ERASE commands. Using these commands can save

considerable time when the cycle time to the device is long. When in unlock bypass

mode, only the following commands are valid:

• The UNLOCK BYPASS PROGRAM command can be issued to program addresses

within the device.

• The UNLOCK BYPASS BLOCK ERASE command can then be issued to erase one or

more memory blocks.

• The UNLOCK BYPASS CHIP ERASE command can be issued to erase the whole mem-

ory array.

• The UNLOCK BYPASS WRITE TO BUFFER PROGRAM and UNLOCK BYPASS EN-

HANCED WRITE TO BUFFER PROGRAM commands can be issued to speed up the

programming operation.

• The UNLOCK BYPASS RESET command can be issued to return the device to read

mode.

In unlock bypass mode, the device can be read as if in read mode.

In addition to the UNLOCK BYPASS command, when VPP/WP# is raised to VPPH, the de-

vice automatically enters unlock bypass mode. When VPP/WP# returns to VIH or VIL, the

device is no longer in unlock bypass mode, and normal operation resumes. The transi-

tions from VIH to VPPH and from VPPH to VIH must be slower than tVHVPP. (See the Accel-

erated Program, Data Polling/Toggle AC Characteristics.)

Note: Micron recommends entering and exiting unlock bypass mode using the ENTER

UNLOCK BYPASS and UNLOCK BYPASS RESET commands rather than raising VPP/WP#

to VPPH. VPP/WP# should never be raised to VPPH from any mode except read mode; oth-

erwise, the device may be left in an indeterminate state. VPP/WP# should not remain at

VPPH for than 80 hours cumulative.

UNLOCK BYPASS RESET Command

The UNLOCK BYPASS RESET (90/00h) command is used to return to read/reset mode

from unlock bypass mode. Two bus WRITE operations are required to issue the UN-

LOCK BYPASS RESET command. The READ/RESET command does not exit from un-

lock bypass mode.

128Mb 3V Embedded Parallel NOR Flash

Bypass Operations

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 29 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Program Operations

PROGRAM Command

The PROGRAM (A0h) command can be used to program a value to one address in the

memory array. The command requires four bus WRITE operations, and the final WRITE

operation latches the address and data in the internal state machine and starts the pro-

gram/erase controller. After programming has started, bus READ operations output the

status register content.

Programming can be suspended and then resumed by issuing a PROGRAM SUSPEND

command and a PROGRAM RESUME command, respectively.

If the address falls in a protected block, the PROGRAM command is ignored, and the

data remains unchanged. The status register is not read, and no error condition is given.

After the PROGRAM operation has completed, the device returns to read mode, unless

an error has occurred. When an error occurs, bus READ operations to the device contin-

ue to output the status register. A READ/RESET command must be issued to reset the

error condition and return the device to read mode.

The PROGRAM command cannot change a bit set to 0 back to 1, and an attempt to do

so is masked during a PROGRAM operation. Instead, an ERASE command must be used

to set all bits in one memory block or in the entire memory from 0 to 1.

The PROGRAM operation is aborted by performing a reset or by powering-down the de-

vice. In this case, data integrity cannot be ensured, and it is recommended that the

words or bytes that were aborted be reprogrammed.

UNLOCK BYPASS PROGRAM Command

When the device is in unlock bypass mode, the UNLOCK BYPASS PROGRAM (A0h)

command can be used to program one address in the memory array. The command re-

quires two bus WRITE operations instead of four required by a standard PROGRAM

command; the final WRITE operation latches the address and data and starts the pro-

gram/erase controller (The standard PROGRAM command requires four bus WRITE op-

erations). The PROGRAM operation using the UNLOCK BYPASS PROGRAM command

behaves identically to the PROGRAM operation using the PROGRAM command. The

operation cannot be aborted. A bus READ operation to the memory outputs the status

WRITE TO BUFFER PROGRAM Command

The WRITE TO BUFFER PROGRAM (25h) command makes use of the 32-word program

buffer to speed up programming. A maximum of 32 words can be loaded into the pro-

gram buffer. The WRITE TO BUFFER PROGRAM command dramatically reduces system

programming time compared to the standard non-buffered PROGRAM command.

When issuing a WRITE TO BUFFER PROGRAM command, V PP/WP# can be either held

HIGH or raised to VPPH. Also, it can be held LOW if the block is not the lowest or highest

block, depending on the part number. The following successive steps are required to is-

sue the WRITE TO BUFFER PROGRAM command:

First, two UNLOCK cycles are issued. Next, a third bus WRITE cycle sets up the WRITE

TO BUFFER PROGRAM command. The set-up code can be addressed to any location

128Mb 3V Embedded Parallel NOR Flash

Program Operations

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 30 Micron Technology, Inc. reserves the right to change products or specifications without notice.

within the targeted block. Then, a fourth bus WRITE cycle sets up the number of words/

bytes to be programmed. Value n is written to the same block address, where n + 1 is the

number of words/bytes to be programmed. Value n + 1 must not exceed the size of the

program buffer, or the operation will abort. A fifth cycle loads the first address and data

to be programmed. Last, n bus WRITE cycles load the address and data for each word/

byte into the program buffer. Addresses must lie within the range from the start address

+1 to the start address + (n - 1).

Optimum programming performance and lower power usage are achieved by aligning

the starting address at the beginning of a 32-word boundary. Any buffer size smaller

than 32 words is allowed within a 32-word boundary, while all addresses used in the op-

eration must lie within the 32-word boundary. In addition, any crossing boundary buf-

fer program will result in a program abort.

To program the content of the program buffer, this command must be followed by a

WRITE TO BUFFER PROGRAM CONFIRM command.

If an address is written several times during a WRITE TO BUFFER PROGRAM operation,

the address/data counter will be decremented at each data load operation, and the data

will be programmed to the last word loaded into the buffer.

Invalid address combinations or the incorrect sequence of bus WRITE cycles will abort

the WRITE TO BUFFER PROGRAM command.

The status register bits DQ1, DQ5, DQ6, DQ7 can be used to monitor the device status

during a WRITE TO BUFFER PROGRAM operation.

The WRITE BUFFER PROGRAM command should not be used to change a bit set to 0

back to 1, and an attempt to do so is masked during the operation. Rather than the

WRITE BUFFER PROGRAM command, the ERASE command should be used to set

memory bits from 0 to 1.

128Mb 3V Embedded Parallel NOR Flash

Program Operations

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 31 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Figure 8: WRITE TO BUFFER PROGRAM Flowchart

Abort

WRITE TO BUFFER

Write buffer data,

start address

Start

X = n

Write n,1

block address

WRITE TO BUFFER

and PROGRAM

aborted2

Write to a different

block address

X = 0

Write next data,3

program address pair

WRITE TO BUFFER

confirm, block address

X = X - 1

Yes

DQ7 = Data

Yes

DQ5 = 1

Yes

DQ1 = 1 No

Yes

WRITE TO BUFFER

command,

block address

Read data polling

DQ7) at last loaded

DQ7 = Data4

Yes

Check data polling

at last loaded address

Fail or

abort5End

First three cycles of the

WRITE TO BUFFER

PROGRAM command

address

Notes: 1. n + 1 is the number of addresses to be programmed.

2. The BUFFERED PROGRAM ABORT and RESET command must be issued to return the de-

vice to read mode.

3. When the block address is specified, any address in the selected block address space is

acceptable. However, when loading program buffer address with data, all addresses

must fall within the selected program buffer page.

4. DQ7 must be checked because DQ5 and DQ7 may change simultaneously.

5. If this flowchart location is reached because DQ5 = 1, then the WRITE TO BUFFER PRO-

GRAM command failed. If this flowchart location is reached because DQ1 = 1, then the

WRITE TO BUFFER PROGRAM command aborted. In both cases, the appropriate RESET

command must be issued to return the device to read mode: A RESET command if the

operation failed; a WRITE TO BUFFER PROGRAM ABORT AND RESET command if the op-

eration aborted.

6. See the Standard Command Definitions – Address-Data Cycles, 8-Bit and 16-Bit table for

details about the WRITE TO BUFFER PROGRAM command sequence.

128Mb 3V Embedded Parallel NOR Flash

Program Operations

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 32 Micron Technology, Inc. reserves the right to change products or specifications without notice.

UNLOCK BYPASS WRITE TO BUFFER PROGRAM Command

When the device is in unlock bypass mode, the UNLOCK BYPASS WRITE TO BUFFER

(25h) command can be used to program the device in fast program mode. The com-

mand requires two bus WRITE operations fewer than the standard WRITE TO BUFFER

PROGRAM command.

The UNLOCK BYPASS WRITE TO BUFFER PROGRAM command behaves the same way

as the WRITE TO BUFFER PROGRAM command: the operation cannot be aborted, and

a bus READ operation to the memory outputs the status register.

The WRITE TO BUFFER PROGRAM CONFIRM command is used to confirm an UN-

LOCK BYPASS WRITE TO BUFFER PROGRAM command and to program the n + 1

words/bytes loaded in the program buffer by this command.

WRITE TO BUFFER PROGRAM CONFIRM Command

The WRITE TO BUFFER PROGRAM CONFIRM (29h) command is used to confirm a

WRITE TO BUFFER PROGRAM command and to program the n + 1 words/bytes loaded

in the program buffer by this command.

BUFFERED PROGRAM ABORT AND RESET Command

A BUFFERED PROGRAM ABORT AND RESET (F0h) command must be issued to abort

the WRITE TO BUFFER PROGRAM and ENHANCED BUFFERED PROGRAM operations

and reset the device in read mode. The buffer programming sequence can be aborted in

the following ways:

• Load a value that is greater than the page buffer size during the number of locations

to program in the WRITE TO BUFFER PROGRAM command.

• Write to an address in a different block than the one specified during the WRITE BUF-

FER LOAD command.

• Write an address/data pair to a different write buffer page than the one selected by

the starting address during the program buffer data loading stage of the operation.

• Write data other than the CONFIRM command after the specified number of data

load cycles.

The abort condition is indicated by DQ1 = 1, DQ7 = DQ7# (for the last address location

loaded), DQ6 = toggle, and DQ5 = 0 (all of which are status register bits). A BUFFERED

PROGRAM ABORT and RESET command sequence must be written to reset the device

for the next operation.

Note: The full three-cycle BUFFERED PROGRAM ABORT and RESET command se-

quence is required when using buffer programming features in unlock bypass mode.

PROGRAM SUSPEND Command

The PROGRAM SUSPEND (B0h) command can be used to interrupt a program opera-

tion so that data can be read from any block. When the PROGRAM SUSPEND command

is issued during a program operation, the device suspends the operation within the pro-

gram suspend latency time and updates the status register bits.

After the program operation has been suspended, data can be read from any address.

However, data is invalid when read from an address where a program operation has

been suspended.

128Mb 3V Embedded Parallel NOR Flash

Program Operations

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 33 Micron Technology, Inc. reserves the right to change products or specifications without notice.

The PROGRAM SUSPEND command may also be issued during a PROGRAM operation

while an erase is suspended. In this case, data may be read from any address not in

erase suspend or program suspend mode. To read from the extended memory block

area (one-time programmable area), the ENTER/EXIT EXTENDED MEMORY BLOCK

command sequences must be issued.

The system may also issue the AUTO SELECT command sequence when the device is in

program suspend mode. The system can read as many auto select codes as required.

When the device exits auto select mode, the device reverts to program suspend mode

and is ready for another valid operation.

The PROGRAM SUSPEND operation is aborted by performing a device reset or power-

down. In this case, data integrity cannot be ensured, and it is recommended that the

words or bytes that were aborted be reprogrammed.

PROGRAM RESUME Command

The PROGRAM RESUME (30h) command must be issued to exit a program suspend

mode and resume a PROGRAM operation. The controller can use DQ7 or DQ6 status

bits to determine the status of the PROGRAM operation. After a PROGRAM RESUME

command is issued, subsequent PROGRAM RESUME commands are ignored. Another

PROGRAM SUSPEND command can be issued after the device has resumed program-

ming.

ENHANCED BUFFERED PROGRAM Command

The ENHANCED BUFFERED PROGRAM command (x16 only) makes use of a 256-word

write buffer to speed up programming. Each write buffer has the same A22-A8 address-

es. This command dramatically reduces system programming time compared to both

the standard non-buffered PROGRAM command and the WRITE TO BUFFER com-

mand.

When issuing the ENHANCED BUFFERED PROGRAM command, the VPP/WP pin can

be held HIGH or raised to VPPH (see Program/Erase Characteristics). The following suc-

cessive steps are required to issue the ENHANCED BUFFERED PROGRAM command:

The ENHANCED BUFFERED PROGRAM command begins with two unlock cycles, fol-

lowed by one bus write cycle that sets up the command. The setup code can be ad-

dressed to any location within the targeted block. Next, another bus write cycle loads

the first address and data to be programmed. There a total of 256 address and data load-

ing cycles. To program the content of the write buffer, the ENHANCED BUFFERED

PROGRAM command must be followed by an ENHANCED BUFFERED PROGRAM

CONFIRM command. The command ends with an internal enhanced buffered program

confirm cycle.

Address/data cycles must be loaded in an increasing address order, from A[7:0] =

00000000 to A[7:0] = 11111111 until all 256 words are loaded. Invalid address combina-

tions or the incorrect sequence of bus WRITE cycles will abort the WRITE TO BUFFER

PROGRAM command.

The status register bits DQ1, DQ5, DQ6, DQ7 can be used to monitor the device status

during a WRITE TO BUFFER PROGRAM operation.

An external 12V supply can be used to improve programming efficiency.

128Mb 3V Embedded Parallel NOR Flash

Program Operations

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 34 Micron Technology, Inc. reserves the right to change products or specifications without notice.

When reprogramming data in a portion of memory already programmed (changing

programmed data from '0' to '1') operation failure can be detected by a logical OR be-

tween the previous and the current value.

UNLOCK BYPASS ENHANCED BUFFERED PROGRAM Command

The UNLOCK BYPASS ENHANCED BUFFERED PROGRAM command can be used to

program the memory in fast program mode. The command requires two less address/

data loading cycles than the standard ENHANCED BUFFERED PROGRAM command.

Otherwise, the two operations behave identically. The operation cannot be aborted and

a READ operation to the memory outputs the status register. The ENHANCED BUF-

FERED PROGRAM CONFIRM command confirms the command and programs the 256

words loaded in the buffer.

ENHANCED BUFFERED PROGRAM CONFIRM Command

The ENHANCED BUFFERED PROGRAM CONFIRM command is used to confirm the

two ENHANCED BUFFERED PROGRAM CONFIRM commands and to program the 256

words loaded in the buffer.

128Mb 3V Embedded Parallel NOR Flash

Program Operations

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 35 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Figure 9: ENHANCED BUFFERED PROGRAM Flowchart

ENHANCED

BUFFERED PROGRAM

command set

Start

Read

DQ5 and DQ6

at valid address

DQ6 =

toggle

DQ5 =1

Read DQ6

twice

at valid address

DQ6 =

toggle

Fail

Read DQ6 at

valid address

Read status register

(DQ1, DQ5, DQ7) at

last loaded address

DQ7 = Data

Check status register

(DQ5, DQ7) at

last loaded address

DQ5 = 1

DQ7 = Data

(3)

ENHANCED BUFFERED

PROGRAM confirm,

block address

Fail or Abort(4)

258th WRITE cycle of the

command

ENHANCED BUFFERED PROGRAM

End

New

Program?

Exit ENHANCED

BUFFERED PROGRAM

command set

Yes

DQ1 = 1

Yes

X = X-1

Write buffer data,

start address (00),

X=255

X = 0

Abort WRITE

TO BUFFER

Write next data, (2)

program address pair

Yes

Write to a different

block address

ENHANCED BUFFERED

PROGRAM aborted (1)

ENHANCED BUFFERED

PROGRAM command,

block address

Write next data, (2)

program address pair

First cycle of the

ENHANCED BUFFERED PROGRAM

command

Yes

Notes: 1. The BUFFERED PROGRAM ABORT AND RESET command must be issued to return the de-

vice to read mode.

128Mb 3V Embedded Parallel NOR Flash

Program Operations

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 36 Micron Technology, Inc. reserves the right to change products or specifications without notice.

2. When the block address is specified, all addresses in the selected block address space

must be issued starting from 00h. Furthermore, when loading the write buffer address

with data, data program addresses must be consecutive.

3. DQ7 must be checked since DQ5 and DQ7 may change simultaneously.

4. If this flowchart location is reached because DQ5 = 1, then the ENHANCED WRITE TO

BUFFER PROGRAM command failed. If this flowchart location is reached because DQ1 =

1, then the ENHANCED WRITE TO BUFFER PROGRAM command aborted. In both cases,

the appropriate RESET command must be issued to return the device to read mode: A

RESET command if the operation failed; a WRITE TO BUFFER PROGRAM ABORT AND RE-

SET command if the operation aborted.

128Mb 3V Embedded Parallel NOR Flash

Program Operations

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 37 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Erase Operations

CHIP ERASE Command

The CHIP ERASE (80/10h) command erases the entire chip. Six bus WRITE operations

are required to issue the command and start the program/erase controller.

Protected blocks are not erased. If all blocks are protected, the CHIP ERASE operation

appears to start, but will terminate within approximately100μs, leaving the data un-

changed. No error is reported when protected blocks are not erased.

During the CHIP ERASE operation, the device ignores all other commands, including

ERASE SUSPEND. It is not possible to abort the operation. All bus READ operations dur-

ing CHIP ERASE output the status register on the data I/Os. (See the Status Register sec-

tion for more details.)

After the CHIP ERASE operation completes, the device returns to read mode, unless an

error has occurred. If an error occurs, the device will continue to output the status regis-

ter. A READ/RESET command must be issued to reset the error condition and return to

read mode.

The CHIP ERASE command sets all of the bits in unprotected blocks of the device to 1.

All previous data is lost.

The operation is aborted by performing a reset or by powering-down the device. In this

case, data integrity cannot be ensured, and the entire chip should be erased again.

UNLOCK BYPASS CHIP ERASE Command

When the device is in unlock bypass mode, the UNLOCK BYPASS CHIP ERASE (80/10h)

command can be used to erase all memory blocks at one time. The command requires

only two bus WRITE operations instead of six using the standard CHIP ERASE com-

mand. The final bus WRITE operation starts the program/erase controller.

The UNLOCK BYPASS CHIP ERASE command behaves the same way as the CHIP

ERASE command: the operation cannot be aborted, and a bus READ operation to the

memory outputs the status register.

BLOCK ERASE Command

The BLOCK ERASE (80/30h) command erases a list of one or more blocks. It sets all of

the bits in the unprotected selected blocks to 1. All previous data in the selected blocks

is lost.

Six bus WRITE operations are required to select the first block in the list. Each addition-

al block in the list can be selected by repeating the sixth bus WRITE operation using the

address of the additional block. After the command sequence is written, a block erase

timeout occurs. During the timeout period, additional block addresses and BLOCK

ERASE commands can be written. After the program/erase controller has started, it is

not possible to select any more blocks. Each additional block must therefore be selected

within the timeout period of the last block. The timeout timer restarts when an addi-

tional block is selected. After the sixth bus WRITE operation, a bus READ operation out-

puts the status register. (See the WE#-Controlled Program waveforms for details on how

to identify if the program/erase controller has started the BLOCK ERASE operation.)

128Mb 3V Embedded Parallel NOR Flash

Erase Operations

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 38 Micron Technology, Inc. reserves the right to change products or specifications without notice.

After the BLOCK ERASE operation completes, the device returns to read mode, unless

an error has occurred. If an error occurs, bus READ operations will continue to output

the status register. A READ/RESET command must be issued to reset the error condi-

tion and return to read mode.

If any selected blocks are protected, they are ignored, and all the other selected blocks

are erased. If all the selected blocks are protected, the BLOCK ERASE operation appears

to start, but will terminate within approximately100μs, leaving the data unchanged. No

error condition is given when protected blocks are not erased.

During the BLOCK ERASE operation, the device ignores all commands except the

ERASE SUSPEND command and the READ/RESET command, which is accepted only

during the timeout period. The operation is aborted by performing a reset or powering-

down the device. In this case, data integrity cannot be ensured, and the aborted blocks

should be erased again.

UNLOCK BYPASS BLOCK ERASE Command

When the device is in unlock bypass mode, the UNLOCK BYPASS BLOCK ERASE

(80/30h) command can be used to erase one or more memory blocks at a time. The

command requires two bus WRITE operations instead of six using the standard BLOCK

ERASE command. The final bus WRITE operation latches the address of the block and

starts the program/erase controller.

To erase multiple blocks (after the first two bus WRITE operations have selected the first

block in the list), each additional block in the list can be selected by repeating the sec-

ond bus WRITE operation using the address of the additional block.

The UNLOCK BYPASS BLOCK ERASE command behaves the same way as the BLOCK

ERASE command: the operation cannot be aborted, and a bus READ operation to the

memory outputs the status register. (See the BLOCK ERASE Command section for de-

tails.)

ERASE SUSPEND Command

The ERASE SUSPEND (B0h) command temporarily suspends a BLOCK ERASE opera-

tion. One bus WRITE operation is required to issue the command. The block address is

"Don't Care."

The program/erase controller suspends the ERASE operation within the erase suspend

latency time of the ERASE SUSPEND command being issued. However, when the

ERASE SUSPEND command is written during the block erase timeout, the device im-

mediately terminates the timeout period and suspends the ERASE operation. After the

program/erase controller has stopped, the device operates in read mode, and the erase

is suspended.

During an ERASE SUSPEND operation, it is possible to read and execute PROGRAM op-

erations or WRITE TO BUFFER PROGRAM operations in blocks that are not suspended.

Both READ and PROGRAM operations behave normally on these blocks. Reading from

blocks that are suspended will output the status register. If any attempt is made to pro-

gram in a protected block or in the suspended block, the PROGRAM command is ignor-

ed, and the data remains unchanged. In this case, the status register is not read, and no

error condition is given.

128Mb 3V Embedded Parallel NOR Flash

Erase Operations

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 39 Micron Technology, Inc. reserves the right to change products or specifications without notice.

It is also possible to issue AUTO SELECT and UNLOCK BYPASS commands during an

ERASE SUSPEND operation. The READ/RESET command must be issued to return the

device to read array mode before the RESUME command will be accepted.

During an ERASE SUSPEND operation, a bus READ operation to the extended memory

block will output the extended memory block data. After the device enters extended

memory block mode, the EXIT EXTENDED MEMORY BLOCK command must be issued

before the ERASE operation can be resumed.

An ERASE SUSPEND command is ignored if it is written during a CHIP ERASE opera-

tion.

If the ERASE SUSPEND operation is aborted by performing a device reset or power-

down, data integrity cannot be ensured, and the suspended blocks should be erased

again.

ERASE RESUME Command

The ERASE RESUME (30h) command restarts the program/erase controller after an

ERASE SUSPEND operation.

The device must be in read array mode before the RESUME command will be accepted.

An erase can be suspended and resumed more than once.

128Mb 3V Embedded Parallel NOR Flash

Erase Operations

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 40 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Block Protection Command Definitions – Address-Data Cycles

Table 12: Block Protection Command Definitions – Address-Data Cycles, 8-Bit and 16-Bit

Notes 1 and 2 apply to entire table

Command and

Code/Subcode

Bus

Size

Address and Data Cycles

Notes

1st 2nd 3rd 4th

…

nth

A D A D A D A D A D

LOCK REGISTER Commands

ENTER LOCK REGISTER

COMMAND SET (40h)

x8 AAA AA 555 55 AAA 40 3

x16 555 AA 2AA 55 555

PROGRAM LOCK REGISTER

(A0h)

x8 X A0 X Data 5

x16

READ LOCK REGISTER x8 X Data 4, 5, 6

x16

PASSWORD PROTECTION Commands

ENTER PASSWORD

PROTECTION COMMAND

SET (60h)

x8 AAA AA 555 55 AAA 60 3

x16 555 AA 2AA 55 555

PROGRAM PASSWORD

(A0h)

x8 X A0 PWAn PWDn 7

x16

READ PASSWORD x8 00 PWD0 01 PWD1 02 PWD2 03 PWD3 … 07 PWD7 4, 6, 8,

x16 00 PWD0 01 PWD1 02 PWD2 03 PWD3

UNLOCK PASSWORD

(25h/03)

x8 00 25 00 03 00 PWD0 01 PWD1 … 00 29 8, 10

x16

NONVOLATILE PROTECTION Commands

ENTER NONVOLATILE

PROTECTION COMMAND

SET (C0h)

x8 AAA AA 555 55 AAA C0 3

x16 555 AA 2AA 55 555

PROGRAM NONVOLATILE

PROTECTION BIT (A0h)

x8 X A0 BAd 00

x16

READ NONVOLATILE

PROTECTION BIT STATUS

x8 BAd READ(0) 4, 6,

x16

CLEAR ALL NONVOLATILE

PROTECTION BITS (80/30h)

x8 X 80 00 30 12

x16

NONVOLATILE PROTECTION BIT LOCK BIT Commands

ENTER NONVOLATILE

PROTECTION BIT LOCK BIT

COMMAND SET (50h)

x8 AAA AA 555 55 AAA 50 3

x16 555 AA 2AA 55 555

PROGRAM NONVOLATILE

PROTECTION BIT LOCK BIT

(A0h)

x8 X A0 X 00 11

x16

128Mb 3V Embedded Parallel NOR Flash

Block Protection Command Definitions – Address-Data Cycles

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 41 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 12: Block Protection Command Definitions – Address-Data Cycles, 8-Bit and 16-Bit (Continued)

Notes 1 and 2 apply to entire table

Command and

Code/Subcode

Bus

Size

Address and Data Cycles

Notes

1st 2nd 3rd 4th

…

nth

A D A D A D A D A D

READ NONVOLATILE

PROTECTION BIT LOCK BIT

STATUS

x8 X READ(0) 4, 6,

x16

VOLATILE PROTECTION Commands

ENTER VOLATILE

PROTECTION COMMAND

SET (E0h)

x8 AAA AA 555 55 AAA E0 3

x16 555 AA 2AA 55 555

PROGRAM VOLATILE

PROTECTION BIT (A0h)

x8 X A0 BAd 00

x16

READ VOLATILE

PROTECTION BIT STATUS

x8 BAd READ(0) 4, 6,

x16

CLEAR VOLATILE

PROTECTION BIT (A0h)

x8 X A0 BAd 01

x16

EXTENDED MEMORY BLOCK Commands

ENTER EXTENDED

MEMORY BLOCK (88h)

x8 AAA AA 555 55 AAA 88 3

x16 555 AA 2AA 55 555

EXIT EXTENDED

MEMORY BLOCK (90/00h)

x8 AAA AA 555 55 AAA 90 X 00

x16 555 AA 2AA 55 555

EXIT PROTECTION Commands

EXIT PROTECTION

COMMAND SET (90/00h)

x8 X 90 X 00 3

x16

Notes: 1. Key: A = Address and D = Data; X = "Don’t Care;" BAd = any address in the block; PWDn

= password bytes 0 to 7; PWAn = password address, n = 0 to 7; Gray = not applicable. All

values in the table are hexadecimal.

2. DQ[15:8] are "Don’t Care" during UNLOCK and COMMAND cycles. A[MAX:16] are

"Don’t Care" during UNLOCK and COMMAND cycles, unless an address is required.

3. The ENTER command sequence must be issued prior to any operation. It disables READ

and WRITE operations from and to block 0. READ and WRITE operations from and to

any other block are allowed. Also, when an ENTER COMMAND SET command is issued,

an EXIT PROTECTION COMMAND SET command must be issued to return the device to

READ mode.

4. READ REGISTER/PASSWORD commands have no command code; CE# and OE# are driven

LOW and data is read according to a specified address.

5. Data = Lock register content.

6. All address cycles shown for this command are READ cycles.

7. Only one portion of the password can be programmed or read by each PROGRAM PASS-

WORD command.

8. Each portion of the password can be entered or read in any order as long as the entire

64-bit password is entered or read.

128Mb 3V Embedded Parallel NOR Flash

Block Protection Command Definitions – Address-Data Cycles

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 42 Micron Technology, Inc. reserves the right to change products or specifications without notice.

9. For the x8 READ PASSWORD command, the nth (and final) address cycle equals the 8th

address cycle. From the 5th to the 8th address cycle, the values for each address and da-

ta pair continue the pattern shown in the table as follows: for x8, address and data = 04

and PWD4; 05 and PWD5; 06 and PWD6; 07 and PWD7.

10. For the x8 UNLOCK PASSWORD command, the nth (and final) address cycle equals the

11th address cycle. From the 5th to the 10th address cycle, the values for each address

and data pair continue the pattern shown in the table as follows: address and data = 02

and PWD2; 03 and PWD3; 04 and PWD4; 05 and PWD5; 06 and PWD6; 07 and PWD7.

For the x16 UNLOCK PASSWORD command, the nth (and final) address cycle equals the

7th address cycle. For the 5th and 6th address cycles, the values for the address and data

pair continue the pattern shown in the table as follows: address and data = 02 and

PWD2; 03 and PWD3.

11. Both nonvolatile and volatile protection bit settings are as follows: Protected state = 00;

Unprotected state= 01.

12. The CLEAR ALL NONVOLATILE PROTECTION BITS command programs all nonvolatile pro-

tection bits before erasure. This prevents over-erasure of previously cleared nonvolatile

protection bits.

128Mb 3V Embedded Parallel NOR Flash

Block Protection Command Definitions – Address-Data Cycles

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 43 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Protection Operations

Blocks can be protected individually against accidental PROGRAM, ERASE, or READ op-

erations on both 8-bit and 16-bit configurations. The block protection scheme is shown

in the Software Protection Scheme figure. Memory block and extended memory block

protection is configured through the lock register.

LOCK REGISTER Commands

The ENTER LOCK REGISTER COMMAND SET (40h) command enables execution of all

READ or PROGRAM LOCK REGISTER commands. PROGRAM LOCK REGISTER (A0h)

configures the lock register, and READ LOCK REGISTER reads/confirms programmed

data.

PASSWORD PROTECTION Commands

The ENTER PASSWORD PROTECTION COMMAND SET (60h) command enables execu-

tion of password protection commands. PROGRAM PASSWORD (A0h) programs the 64-

bit password used in the password protection mode. To program the 64-bit password in

8-bit mode, the complete command sequence must be entered eight times at eight con-

secutive addresses selected by A[1:0] plus DQ15/A-1; in 16-bit mode, the command se-

quence must be entered four times at four consecutive addresses selected by A[1:0]. By

default, all password bits are set to 1. The password can be checked by issuing a READ

PASSWORD command.

READ PASSWORD verifies the password used in password protection mode. To verify

the 64-bit password in 8-bit mode, the complete command sequence must be entered

eight times at eight consecutive addresses selected by A[1:0] plus DQ15/A-1. In 16-bit

mode, the command sequence must be entered four times at four consecutive address-

es selected by A[1:0]. If the password mode lock bit is programmed, and a user attempts

to read the password, the device outputs FFh.

UNLOCK PASSWORD (25/03h) clears the nonvolatile protection bit lock bit, allowing

the nonvolatile protection bits to be modified. UNLOCK PASSWORD must be issued

with the correct password and requires a 1μs delay between successive UNLOCK PASS-

WORD commands. The delay helps prevent password intruders from trying all possible

64-bit combinations. If the delay does not occur, the latest command is ignored. After a

valid 64-bit password is entered, approximately 1μs is required to unlock the device.

NONVOLATILE PROTECTION Commands

The ENTER NONVOLATILE PROTECTION COMMAND SET (C0h) command enables

nonvolatile protection mode commands to be issued to the device. A block can be pro-

tected from PROGRAM or ERASE operations using a PROGRAM NONVOLATILE PRO-

TECTION BIT (A0h) command, along with the block address. This command sets the

nonvolatile protection bit to 0 for a given block.

The status of a nonvolatile protection bit for a given block or group of blocks can be

read using a READ NONVOLATILE MODIFY PROTECTION BIT command, along with

the block address. The nonvolatile protection bits are erased simultaneously using a

CLEAR ALL NONVOLATILE PROTECTION BITS (80/30h) command. No specific block

address is required. If the nonvolatile protection bit lock bit is set to 0, the command

fails.

128Mb 3V Embedded Parallel NOR Flash

Protection Operations

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 44 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Figure 10: Program/Erase Nonvolatile Protection Bit Algorithm

Yes

DQ6 = Toggle

ENTER NONVOLATILE

PROTECTION

command set

Start

PROGRAM NONVOLATILE

PROTECTION BIT

Addr = BAd

Fail

Read byte twice

Addr = BAd

Read byte twice

Addr = BAd

Yes

DQ6 = Toggle

Reset

DQ5 = 1

EXIT PROTECTION

command set

DQ0 =

1 (erase)

0 (program)

Read byte twice

Addr = BAd

Wait 500µs

Pass

128Mb 3V Embedded Parallel NOR Flash

Protection Operations

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 45 Micron Technology, Inc. reserves the right to change products or specifications without notice.

NONVOLATILE PROTECTION BIT LOCK BIT Commands

After the ENTER NONVOLATILE PROTECTION BIT LOCK BIT COMMAND SET (50h)

command has been issued, the commands that allow the nonvolatile protection bit lock

bit to be set can be issued to the device.

The PROGRAM NONVOLATILE PROTECTION BIT LOCK BIT (A0h) command is used to

set the nonvolatile protection bit lock bit to 0, thus locking the nonvolatile protection

bits and preventing them from being modified.

The READ NONVOLATILE PROTECTION BIT LOCK BIT STATUS command is used to

read the status of the nonvolatile protection bit lock bit.

VOLATILE PROTECTION Commands

After the ENTER VOLATILE PROTECTION COMMAND SET (E0h) command has been

issued, commands related to the volatile protection mode can be issued to the device.

The PROGRAM VOLATILE PROTECTION BIT (A0h) command individually sets a vola-

tile protection bit to 0 for a given block. If the nonvolatile protection bit for the same

block is set, the block is locked regardless of the value of the volatile protection bit. (See

the Block Protection Status table.)

The status of a volatile protection bit for a given block can be read by issuing a READ

VOLATILE PROTECTION BIT STATUS command along with the block address.

The CLEAR VOLATILE PROTECTION BIT (A0h) command individually clears (sets to 1)

the volatile protection bit for a given block. If the nonvolatile protection bit for the same

block is set, the block is locked regardless of the value of the volatile protection bit. (See

the Block Protection Status table.)

EXTENDED MEMORY BLOCK Commands

The device has one extra 128-word extended memory block that can be accessed only

by the ENTER EXTENDED MEMORY BLOCK (88h) command. The extended memory

block is 128 words (x16) or 256 bytes (x8). It is used as a security block to provide a per-

manent 128-bit security identification number or to store additional information. The

device can be shipped with the extended memory block prelocked permanently by Mi-

cron, including the 128-bit security identification number. Or, the device can be ship-

ped with the extended memory block unlocked, enabling customers to permanently

program and lock it. (See Lock Register, the AUTO SELECT command, and the Block

Protection table.)

Table 13: Extended Memory Block Address and Data

Address Data

x8 x16 Micron-Prelocked Customer-Lockable

000000h–0000FFh 000000h–00007Fh Secure ID number Determined by customer

After the ENTER EXTENDED MEMORY BLOCK command has been issued, the device

enters the extended memory block mode. All bus READ or PROGRAM operations are

conducted on the extended memory block, and the extended memory block is ad-

dressed using the addresses occupied by block 0 in the other operating modes. (See the

Memory Map table.)

128Mb 3V Embedded Parallel NOR Flash

Protection Operations

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 46 Micron Technology, Inc. reserves the right to change products or specifications without notice.

In extended memory block mode, ERASE, CHIP ERASE, ERASE SUSPEND, and ERASE

RESUME commands are not allowed. The extended memory block cannot be erased,

and each bit of the extended memory block can only be programmed once.

The extended memory block is protected from further modification by programming

lock register bit 0. Once invoked, this protection cannot be undone.

The device remains in extended memory block mode until the EXIT EXTENDED MEM-

ORY BLOCK (90/00h) command is issued, which returns the device to read mode, or

until power is removed from the device. After a power-up sequence or hardware reset,

the device will revert to reading memory blocks in the main array.

EXIT PROTECTION Command

The EXIT PROTECTION COMMAND SET (90/00h) command is used to exit the lock

tile protection bit lock bit command set modes and return the device to read mode.

128Mb 3V Embedded Parallel NOR Flash

Protection Operations

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 47 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Device Protection

Hardware Protection

The VPP/WP# function provides a hardware method of protecting the highest or lowest

block. When V PP/WP# is LOW, PROGRAM and ERASE operations on either of these

blocks is ignored to provide protection. When V PP/WP# is HIGH, the device reverts to

the previous protection status for the highest or lowest block. PROGRAM and ERASE

operations can modify the data in this block unless the block is protected using block

protection.

When VPP/WP# protect is raised to VPPH, the device automatically enters the unlock by-

pass mode, and command execution time is faster. This must never be done from any

mode except read mode; otherwise, the device might be left in an indeterminate state.

A 0.1μF capacitor should be connected between VPP/WP# and the VSS ground pin to de-

couple the current surges from the power supply. The PCB track widths must be suffi-

cient to carry the currents required during unlock bypass program.

When VPP/WP# returns to HIGH or LOW, normal operation resumes. When operations

execute in unlock bypass mode, the device draws IPP from the pin to supply the pro-

gramming circuits. Transitions from HIGH to VPPH and from VPPH to LOW must be slow-

er than tVHVPP.

Note: Micron highly recommends driving VPP/WP# HIGH or LOW. If a system needs to

float VPP/WP#, without a pull-up/pull-down resistor and no capacitor, then an internal

pull-up resistor is enabled.

Table 14: VPP/WP# Functions

VPP/WP# Settings Function

VIL Highest (29WxxxGH) or lowest (29WxxxGL) block is protected.

VIH Highest or lowest block is unprotected unless software protection is activated.

VPPH Unlock bypass mode supplies current necessary to speed up PROGRAM execution time.

Software Protection

Software protection includes volatile, nonvolatile, and password protection as well as

password access. The device is shipped with all blocks unprotected. On first use, the de-

vice defaults to the nonvolatile protection mode but can be activated in either the non-

volatile protection or password protection mode.

The desired protection mode is activated by setting either the nonvolatile protection

mode lock bit or the password protection mode lock bit of the lock register. (See the

Lock Register section.) Both bits are one-time-programmable and nonvolatile; there-

fore, after the protection mode has been activated, it cannot be changed, and the device

is set permanently to operate in the selected protection mode. It is recommended that

the desired software protection mode be activated when first programming the device.

For the lowest and highest blocks, a higher level of block protection can be achieved by

locking the blocks using nonvolatile protection mode and holding VPP /WP# LOW.

128Mb 3V Embedded Parallel NOR Flash

Device Protection

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 48 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Blocks with volatile protection and nonvolatile protection can coexist within the memo-

ry array. If the user attempts to program or erase a protected block, the device ignores

the command and returns to read mode.

The block protection status can be read by performing a read electronic signature or by

issuing an AUTO SELECT command. (See the Block Protection table.)

Refer to the Block Protection Status table and the Software Protection Scheme figure for

details on the block protection scheme. Refer to the Protection Operations section for a

description of the command sets.

Volatile Protection Mode

Volatile protection enables the software application to protect blocks against inadver-

tent change and can be disabled when changes are needed. Volatile protection bits are

unique for each block and can be individually modified. Volatile protection bits control

the protection scheme only for unprotected blocks whose nonvolatile protection bits

are cleared to 1. Issuing a PROGRAM VOLATILE PROTECTION BIT or CLEAR VOLATILE

PROTECTION BIT command sets to 0 or clears to 1 the volatile protection bits and pla-

ces the associated blocks in the protected (0) or unprotected (1) state, respectively. The

volatile protection bit can be set or cleared as often as needed.

When the device is first shipped, or after a power-up or hardware reset, the volatile pro-

tection bits default to 1 (unprotected).

Nonvolatile Protection Mode

A nonvolatile protection bit is assigned to each block. Each of these bits can be set for

protection individually by issuing a PROGRAM NONVOLATILE PROTECTION BIT com-

mand. Also, each device has one global volatile bit called the nonvolatile protection bit

lock bit; it can be set to protect all nonvolatile protection bits at once. This global bit

must be set to 0 only after all nonvolatile protection bits are configured to the desired

settings. When set to 0, the nonvolatile protection bit lock bit prevents changes to the

state of the nonvolatile protection bits. When cleared to 1, the nonvolatile protection

bits can be set and cleared using the PROGRAM NONVOLATILE PROTECTION BIT and

CLEAR ALL NONVOLATILE PROTECTION BITS commands, respectively.

No software command unlocks the nonvolatile protection bit lock bit unless the device

is in password protection mode; in nonvolatile protection mode, the nonvolatile protec-

tion bit lock bit can be cleared only by taking the device through a hardware reset or

power-up.

Nonvolatile protection bits cannot be cleared individually; they must be cleared all at

once using a CLEAR ALL NONVOLATILE PROTECTION BITS command. They will re-

main set through a hardware reset or a power-down/power-up sequence.

If one of the nonvolatile protection bits needs to be cleared (unprotected), additional

steps are required. First, the nonvolatile protection bit lock bit must be cleared to 1, us-

ing either a power-cycle or hardware reset. Then, the nonvolatile protection bits can be

changed to reflect the desired settings. Finally, the nonvolatile protection bit lock bit

must be set to 0 to lock the nonvolatile protection bits. The device now will operate nor-

mally.

To achieve the best protection, the PROGRAM NONVOLATILE PROTECTION LOCK BIT

command should be executed early in the boot code, and the boot code should be pro-

tected by holding VPP/WP# LOW.

128Mb 3V Embedded Parallel NOR Flash

Device Protection

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 49 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Nonvolatile protection bits and volatile protection bits have the same function when

VPP/WP# is HIGH or when VPP/WP# is at the voltage for program acceleration (VPPH ).

Password Protection Mode

Password protection mode provides a higher level of security than the nonvolatile pro-

tection mode by requiring a 64-bit password to unlock the nonvolatile protection bit

lock bit. In addition to this password requirement, the nonvolatile protection bit lock

bit is set to 0 after power-up and reset to maintain the device in password protection

mode.

Executing the UNLOCK PASSWORD command by entering the correct password clears

the nonvolatile protection bit lock bit, enabling the block nonvolatile protection bits to

be modified. If the password provided is incorrect, the nonvolatile protection bit lock

bit remains locked, and the state of the nonvolatile protection bits cannot be modified.

To place the device in password protection mode, the following two steps are required:

First, before activating the password protection mode, a 64-bit password must be set

and the setting verified. Password verification is allowed only before the password pro-

tection mode is activated. Next, password protection mode is activated by program-

ming the password protection mode lock bit to 0. This operation is irreversible. After the

bit is programmed, it cannot be erased, the device remains permanently in password

protection mode, and the 64-bit password can be neither retrieved nor reprogrammed.

In addition, all commands to the address where the password is stored are disabled.

Note: There is no means to verify the password after password protection mode is ena-

bled. If the password is lost after enabling the password protection mode, there is no

way to clear the nonvolatile protection bit lock bit.

Figure 11: Software Protection Scheme

1 = unprotected (default)

0 = protected

1 = unprotected

0 = protected

(Default setting depends on the product order option)

Volatile protection bit Nonvolatile protection bit

1 = unlocked (default, after power-up or hardware reset)

0 = locked

Nonvolatile protection bit lock bit (volatile)

Nonvolatile protection

mode

Password protection

mode

Volatile

protection

Nonvolatile

protection

Array block

Notes: 1. Volatile protection bits are programmed and cleared individually. Nonvolatile protection

bits are programmed individually and cleared collectively.

2. Once programmed to 0, the nonvolatile protection bit lock bit can be reset to 1 only by

taking the device through a power-up or hardware reset.

128Mb 3V Embedded Parallel NOR Flash

Device Protection

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 50 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Common Flash Interface

The common Flash interface (CFI) is a JEDEC-approved, standardized data structure

that can be read from the Flash memory device. It allows a system's software to query

the device to determine various electrical and timing parameters, density information,

and functions supported by the memory. The system can interface easily with the de-

vice, enabling the software to upgrade itself when necessary.

When the READ CFI command is issued, the device enters CFI query mode and the data

structure is read from memory. The following tables show the addresses (A-1, A[7:0])

used to retrieve the data. The query data is always presented on the lowest order data

outputs (DQ[7:0]), and the other data outputs (DQ[15:8]) are set to 0.

Table 15: Query Structure Overview

Note 1 applies to the entire table

Address

Subsection Name Descriptionx16 x8

10h 20h CFI query identification string Command set ID and algorithm data offset

1Bh 36h System interface information Device timing and voltage information

27h 4Eh Device geometry definition Flash device layout

40h 80h Primary algorithm-specific extended query table Additional information specific to the primary al-

gorithm (optional)

61h C2h Security code area 64-bit unique device number

Note: 1. Query data are always presented on the lowest order data outputs (DQ[7:0]). DQ[15:8]

are set to 0.

Table 16: CFI Query Identification String

Note 1 applies to the entire table

Address

Data Description Valuex16 x8

10h 20h 0051h Query unique ASCII string "QRY" "Q"

11h 22h 0052h "R"

12h 24h 0059h "Y"

13h

14h

26h

28h

0002h

0000h

Primary algorithm command set and control interface ID code 16-bit ID

code defining a specific algorithm

Spansion

compatible

15h

16h

2Ah

2Ch

0040h

0000h

Address for primary algorithm extended query table (see the Primary Algo-

rithm-Specific Extended Query Table)

P = 40h

17h

18h

2Eh

30h

0000h

Alternate vendor command set and control interface ID code second ven-

dor-specified algorithm supported

–

19h

1Ah

32h

34h

0000h

Address for alternate algorithm extended query table –

Note: 1. Query data are always presented on the lowest order data outputs (DQ[7:0]). DQ[15:8]

are set to 0.

128Mb 3V Embedded Parallel NOR Flash

Common Flash Interface

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 51 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 17: CFI Query System Interface Information

Note 1 applies to the entire table

Address

Data Description Valuex16 x8

1Bh 36h 0027h VCC logic supply minimum program/erase voltage

Bits[7:4] BCD value in volts

Bits[3:0] BCD value in 100mV

2.7V

1Ch 38h 0036h VCC logic supply maximum program/erase voltage

Bits[7:4] BCD value in volts

Bits[3:0] BCD value in 100mV

3.6V

1Dh 3Ah 00B5h VPPH (programming) supply minimum program/erase voltage

Bits[7:4] hex value in volts

Bits[3:0] BCD value in 100mV

11.5V

1Eh 3Ch 00C5h VPPH (programming) supply maximum program/erase voltage

Bits[7:4] hex value in volts

Bits[3:0] BCD value in 100mV

12.5V

1Fh 3Eh 0004h Typical timeout for single byte/word program = 2nμs 16µs

20h 40h 0004h Typical timeout for maximum size buffer program = 2nμs 16µs

21h 42h 0009h Typical timeout per individual block erase = 2nms 0.5s

22h 44h 0010h Typical timeout for full chip erase = 2nms 40s

23h 46h 0004h Maximum timeout for byte/word program = 2n times typical 200µs

24h 48h 0004h Maximum timeout for buffer program = 2n times typical 200µs

25h 4Ah 0003h Maximum timeout per individual block erase = 2n times typical 2.3s

26h 4Ch 0004h Maximum timeout for chip erase = 2n times typical 400s

Note: 1. The values in this table are valid for both packages.

Table 18: Device Geometry Definition

Address

Data Description Valuex16 x8

27h 4Eh 0018h Device size = 2n in number of bytes 16MB

28h

29h

50h

52h

0002h

0000h

Flash device interface code description x8, x16

asynchronous

2Ah

2Bh

54h

56h

0006h

0000h

Maximum number of bytes in multi-byte program or page =

64B

2Ch 58h 0001h Number of erase block regions. It specifies the number of

regions containing contiguous erase blocks of the same size.

2Dh

2Eh

5Ah

5Ch

007Fh

0000h

Erase block region 1 information

Number of identical-size erase blocks = 007Fh + 1

128 block

2Fh

30h

5Eh

60h

0000h

0002h

Erase block region 1 information

Block size in region 1 = 0200h × 256 bytes

128KB

128Mb 3V Embedded Parallel NOR Flash

Common Flash Interface

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 52 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 18: Device Geometry Definition (Continued)

Address

Data Description Valuex16 x8

31h

32h

33h

34h

62h

64h

66h

68h

0000h

Erase block region 2 information 0

35h

36h

37h

38h

6Ah

6Ch

6Eh

70h

0000h

Erase block region 3 information 0

39h

3Ah

3Bh

3Ch

72h

74h

76h

78h

0000h

Erase block region 4 information 0

Table 19: Primary Algorithm-Specific Extended Query Table

Note 1 applies to the entire table

Address

Data Description Valuex16 x8

40h 80h 0050h Primary algorithm extended query table unique ASCII string “PRI” "P"

41h 82h 0052h "R"

42h 84h 0049h "I"

43h 86h 0031h Major version number, ASCII "1"

44h 88h 0033h Minor version number, ASCII "3"

45h 8Ah 000Dh Address sensitive unlock (bits[1:0]):

00 = Required

01 = Not required

Silicon revision number (bits[7:2])

Yes

90nm

46h 8Ch 0002h Erase suspend:

00 = Not supported

01 = Read only

02 = Read and write

47h 8Eh 0001h Block protection:

00 = Not supported

x = Number of blocks per group

48h 90h 0000h Temporary block unprotect:

00 = Not supported

01 = Supported

49h 92h 0008h Block protect/unprotect:

06 = M29W128GH/M29W128GL

4Ah 94h 0000h Simultaneous operations:

Not supported

–

128Mb 3V Embedded Parallel NOR Flash

Common Flash Interface

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 53 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 19: Primary Algorithm-Specific Extended Query Table (Continued)

Note 1 applies to the entire table

Address

Data Description Valuex16 x8

4Bh 96h 0000h Burst mode:

00 = Not supported

01 = Supported

4Ch 98h 0002h Page mode:

00 = Not supported

02 = 8-word page

4Dh 9Ah 00B5h VPPH supply minimum program/erase voltage:

Bits[7:4] hex value in volts

Bits[3:0] BCD value in 100mV

11.5V

4Eh 9Ch 00C5h VPPH supply maximum program/erase voltage:

Bits[7:4] hex value in volts

Bits[3:0] BCD value in 100mV

12.5V

4Fh 9Eh 00xxh Top/bottom boot block flag:

xx = 04h: M29W128GL, first block protected by VPP/WP#

xx = 05h: M29W128GH, last block protected by VPP/WP#

Uniform +

VPP/WP# protect-

ing highest or

lowest block

50h A0h 0001h Program suspend:

00 = Not supported

01 = Supported

Note: 1. The values in this table are valid for both packages.

Table 20: Security Code Area

Address

Data Descriptionx16 x8

61h C3h, C2h XXXX 64-bit unique device number

62h C5h, C4h XXXX

63h C7h, C6h XXXX

64h C9h, C8h XXXX

128Mb 3V Embedded Parallel NOR Flash

Common Flash Interface

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 54 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Power-Up and Reset Characteristics

Table 21: Power-Up Wait Timing Specifications

Parameter Symbol

70ns or

60ns180ns

Unit NotesMin Min

VCC HIGH to CE# LOW tVCHEL 55 µs 2

VCCQ HIGH to CE# LOW tVCQHEL 55 µs 2

VCC HIGH to WE# LOW tVCHWL 500 µs

VCCQ HIGH to WE# LOW tVCQHWL 500 µs

Notes: 1. Only available upon customer request.

2. VCC and VCCQ ramps must be synchronized during power-up.

Figure 12: Power-Up Timing

VCQHEL

CE#

CCQ

VCQHWL

WE#

VCHEL

VCHWL

128Mb 3V Embedded Parallel NOR Flash

Power-Up and Reset Characteristics

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 55 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 22: Reset AC Characteristics

Condition/Parameter

Symbol 60ns1, 70ns, 80ns

Unit NotesLegacy JEDEC Min Max

RST# LOW to read mode during program or

erase

tREADY tPLRH – 50 µs 2

RST# pulse width tRP tPLPH 10 – µs

RST# HIGH to WE# LOW, CE# LOW, OE# LOW tRH tPHEL,

tPHGL,

tPHWL

50 – ns 2

RST# LOW to standby mode during read mode tRPD – 10 – µs

RST# LOW to standby mode during program or

erase

50 – µs

RB# HIGH to WE# LOW, CE# LOW, OE# LOW tRB tRHEL,

tRHGL,

tRHWL

0 – ns 2

Notes: 1. Only available upon customer request.

2. Sampled only; not 100% tested.

Figure 13: Reset AC Timing – No PROGRAM/ERASE Operation in Progress

tRH

RY/BY#

CE#, OE#, WE#

RST#

tRP

128Mb 3V Embedded Parallel NOR Flash

Power-Up and Reset Characteristics

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 56 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Figure 14: Reset AC Timing During PROGRAM/ERASE Operation

tRB

RY/BY#

CE#, OE#, WE#

RST#

tRP

tRH

tREADY

128Mb 3V Embedded Parallel NOR Flash

Power-Up and Reset Characteristics

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 57 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Absolute Ratings and Operating Conditions

Stresses greater than those listed may cause permanent damage to the device. This is a

stress rating only, and functional operation of the device at these or any other condi-

tions outside those indicated in the operational sections of this specification is not im-

plied. Exposure to absolute maximum rating conditions for extended periods may ad-

versely affect reliability.

Table 23: Absolute Maximum/Minimum Ratings

Parameter Symbol Min Max Unit Notes

Temperature under bias TBIAS –50 125 °C

Storage temperature TSTG –65 150 °C

Input/output voltage VIO –0.6 VCC + 0.6 V 1, 2

Supply voltage VCC –0.6 4 V

Input/output supply voltage VCCQ –0.6 4 V

Identification voltage VID –0.6 13.5 V

Program voltage VPPH –0.6 13.5 V 3

Notes: 1. Minimum voltage may undershoot to −2V during transition and for less than 20ns dur-

ing transitions.

2. Maximum voltage may overshoot to VCC + 2V during transition and for less than 20ns

during transitions.

3. VPPH must not remain at 12V for more than a total of 80 hours.

Table 24: Operating and AC Measurment Conditions

Parameter Symbol

70ns or 60ns180ns

UnitMin Max Min Max

Supply voltage VCC 2.7 3.6 2.7 3.6 V

Input/output supply voltage VCCQ 2.7 3.6 1.65 3.6 V

Ambient operating temperature (range 1) TA1 0 70 0 70 °C

Ambient operating temperature (range 3) TA3 –40 125 –40 125 °C

Ambient operating temperature (range 6) TA6 –40 85 –40 85 °C

Load capacitance CL30 30 pF

Input rise and fall times – – 10 – 10 ns

Input pulse voltages – 0 to VCCQ 0 to VCCQ V

Input/output timing reference voltages – VCCQ/2 VCCQ/2 V

Note: 1. Only available upon customer request.

128Mb 3V Embedded Parallel NOR Flash

Absolute Ratings and Operating Conditions

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 58 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Figure 15: AC Measurement Load Circuit

VCCQ

25kΩ

Device

under

test

0.1µF

VCC

0.1µF

VPP

25kΩ

Note: 1. CL includes jig capacitance.

Figure 16: AC Measurement I/O Waveform

VCCQ

VCCQ/2

Table 25: Input/Output Capacitance

Sampled only, not 100% tested.

Parameter Symbol Test Condition Min Max Unit

Input capacitance CIN VIN = 0V – 6 pF

Output capacitance COUT VOUT = 0V – 12 pF

128Mb 3V Embedded Parallel NOR Flash

Absolute Ratings and Operating Conditions

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 59 Micron Technology, Inc. reserves the right to change products or specifications without notice.

DC Characteristics

Table 26: DC Current Characteristics

Parameter Symbol Conditions Min Typ Max Unit Notes

Input leakage current ILI 0V ≤ VIN ≤ VCC – – ±1 µA 1

Output leakage current ILO 0V ≤ VOUT ≤ VCC – – ±1 µA

VCC read

current

Random read ICC1 CE# = VIL, OE# = VIH,

f = 6 MHz

– – 10 mA

Page read CE# = VIL, OE# = VIH,

f = 10 MHz

– – 15 mA

VCC standby

current

Grade 6 ICC2 CE# = VCCQ ±0.2V – – 100 µA 2

Grade 3 – – 200 µA 2

VCC program/erase current ICC3 Program/

erase

controller

active

VPP/WP# = VIL

or VIH

– – 20 mA 3

VPP/WP# =

VPPH

– – 20 mA

VPP program

current (pro-

gram)

Read or standby

Standby

IPP1 VPP/WP# ≤ VCC – 1 5 µA

Reset IPP2 RST# = VSS ±0.2V – 1 5 µA

PROGRAM opera-

tion

ongoing

IPP3 VPP/WP# = 12V ±5% – 1 10 mA

VPP/WP# = VCC – 1 5 µA

VPP program

current (erase)

ERASE operation

ongoing

IPP4 VPP/WP# = 12V ±5% – 3 10 mA

VPP/WP# = VCC – 1 5 µA

Notes: 1. The maximum input leakage current is ±5µA on the VPP/WP# pin.

2. When the bus is inactive for tAVQV +30ns or more, the memory enters automatic stand-

by.

3. Sampled only; not 100% tested.

128Mb 3V Embedded Parallel NOR Flash

DC Characteristics

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 60 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 27: DC Voltage Characteristics

Parameter Symbol Conditions Min Typ Max Unit Notes

Input LOW voltage VIL VCC ≥ 2.7V –0.5 – 0.3VCCQ V

Input HIGH voltage VIH VCC ≥ 2.7V 0.7VCCQ – VCCQ + 0.4 V

Output LOW voltage VOL IOL = 100µA,

VCC = VCC,min,

VCCQ = VCCQ,min

– – 0.15VCCQ V

Output HIGH voltage VOH IOH = 100µA,

VCC = VCC,min,

VCCQ = VCCQ,min

0.85VCCQ – – V

Identification voltage VID – 11.5 – 12.5 V

Voltage for VPP/WP# program

acceleration

VPPH – 11.4 – 12.6 V

Program/erase lockout supply

voltage

VLKO – 1.8 – 2.5 V 1

Note: 1. Sampled only; not 100% tested.

128Mb 3V Embedded Parallel NOR Flash

DC Characteristics

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 61 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Read AC Characteristics

Table 28: Read AC Characteristics

Parameter

Symbol

Condition

60ns 1

VCCQ = VCC

70ns

VCCQ = VCC

80ns

VCCQ = 1.65V

to VCC

Unit NotesMin Max Min Max Min MaxLegacy JEDEC

Address valid to next ad-

dress valid

tRC tAVAV CE# = VIL,

OE# = VIL

60 – 70 – 80 – ns

Address valid to output val-

tACC tAVQV CE# = VIL,

OE# = VIL

– 60 – 70 – 80 ns

Address valid to output val-

id (page)

tPAGE tAVQV1 CE# = VIL,

OE# = VIL

– 25 – 25 – 30 ns

CE# LOW to output transi-

tion

tLZ tELQX OE# = VIL 0–0–0–ns2

CE# LOW to output valid tEtELQV OE# = VIL – 60 – 70 – 80 ns

OE# LOW to output transi-

tion

tOLZ tGLQX CE# = VIL 0–0–0–ns2

OE# LOW to output valid tOE tGLQV CE# = VIL – 25 – 25 – 30 ns

CE# HIGH to output High-Z tHZ tEHQZ OE# = VIL – 20 – 20 – 30 ns 2

OE# HIGH to output High-Z tDF tGHQZ CE# = VIL – 20 – 20 – 20 ns 2

CE#, OE#, or address transi-

tion to output transition

tOH tEHQX,

tGHQX,

tAXQX

– 0 – 0 – 0 – ns

CE# to BYTE# LOW tELFL tELBL – – 5 – 5 – 5 ns

CE# to BYTE# HIGH tELFH tELBH – – 5 – 5 – 5 ns

BYTE# LOW to output HIgh-

tFLQZ tBLQZ – – 25 – 25 – 25 ns

BYTE# HIGH to output valid tFHQV tBHQV – – 30 – 30 – 30 ns

Notes: 1. Only available upon customer request.

2. Sampled only; not 100% tested.

128Mb 3V Embedded Parallel NOR Flash

Read AC Characteristics

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 62 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Figure 17: Random Read AC Timing (8-Bit Mode)

Valid Valid

tACC tOH

tHZ

tOE

tEtDF

A[22:0]/A-1

CE#

OE#

DQ[15A-1, 14:0] High-Z

Note: 1. BYTE# = VIL

Figure 18: Random Read AC Timing (16-Bit Mode)

Valid Valid

tACC tOH

tHZ

tOE

tEtDF

A[22:0]

CE#

OE#

DQ[7:0] High-Z

Note: 1. BYTE# = VIH

128Mb 3V Embedded Parallel NOR Flash

Read AC Characteristics

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 63 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Figure 19: BYTE Transition AC Timing

Data out

Valid

tACC tOH

tFHQV

tBLQX

tFLQZ

High-Z

A[MAX:0]

A–1

BYTE#

DQ[7:0]

DQ[15:8]

Note: 1. CE# and OE# = VIL

Figure 20: Page Read AC Timing (16-Bit Mode)

Valid

Valid Valid Valid ValidValid Valid Valid

tACC

tPAGE

tOH

tHZ

tOH

tOE

tDF

A[22:3]

A[2:0]

CE#

OE#

DQ[15:0]

DQ[15A-1] Valid Valid Valid Valid Valid Valid Valid

128Mb 3V Embedded Parallel NOR Flash

Read AC Characteristics

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 64 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Write AC Characteristics

Table 29: WE#-Controlled Write AC Characteristics

Parameter Symbol

60ns 1

VCCQ = VCC

70ns

VCCQ = VCC

80ns

VCCQ = 1.65V

to VCC Unit Notes

Legacy JEDEC Min Max Min Max Min Max

Address valid to next address

valid

tWC tAVAV 65 – 70 – 80 – ns

CE# LOW to WE# LOW tCS tELWL 0 – 0 – 0 – ns

WE# LOW to WE# HIGH tWP tWLWH 35 – 35 – 35 – ns

Input valid to WE# HIGH tDS tDVWH 45 – 45 – 45 – ns 2

WE# HIGH to input transition tDH tWHDX 0 – 0 – 0 – ns

WE# HIGH to CE# HIGH tCH tWHEH 0 – 0 – 0 – ns

WE# HIGH to WE# LOW tWPH tWHWL 30 – 30 – 30 – ns

Address valid to WE# LOW tAS tAVWL 0 – 0 – 0 – ns

WE# LOW to address transi-

tion

tAH tWLAX 45 – 45 – 45 – ns

OE# HIGH to WE# LOW – tGHWL 0 – 0 – 0 – ns

WE# HIGH to OE# LOW tOEH tWHGL 0 – 0 – 0 – ns

Program/erase valid to

RY/BY# LOW

tBUSY tWHRL – 30 – 30 – 30 ns 2

VCC HIGH to CE# LOW tVCS tVCHEL 50 – 50 – 50 – µs

Notes: 1. Only available upon customer request.

2. Sampled only; not 100% tested.

128Mb 3V Embedded Parallel NOR Flash

Write AC Characteristics

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 65 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Figure 21: WE#-Controlled Program AC Timing (8-Bit Mode)

AAAh PA PA

3rd cycle 4th cycle READ cycleData polling

tWC tWC

tAS

tWP

tDS

tWHWH1 tDF

tWPH

tAH

tCS

tGHWL tOE

tDH

tOH

tCH

A[22:0]/A-1

CE#

OE#

WE#

DQ[7:0] AOh PD DQ7# DOUT DOUT

Notes: 1. Only the third and fourth cycles of the PROGRAM command are represented. The PRO-

GRAM command is followed by checking of the status register data polling bit and by a

READ operation that outputs the data (DOUT) programmed by the previous PROGRAM

command.

2. PA is the address of the memory location to be programmed. PD is the data to be pro-

grammed.

3. DQ7 is the complement of the data bit being programmed to DQ7 (See Data Polling Bit

[DQ7]).

4. See the following tables for timing details: Read AC Characteristics, WE#-Controlled

Write AC Characteristics, and CE#-Controlled Write AC Characteristics.

128Mb 3V Embedded Parallel NOR Flash

Write AC Characteristics

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 66 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Figure 22: WE#-Controlled Program AC Timing (16-Bit Mode)

555h PA PA

3rd cycle 4th cycle READ cycleData polling

tWC tWC

tAS

tWP

tDS

tWHWH1 tDF

tWPH

tAH

tCS

tGHWL tOE

tDH

tOH

tCH

A[22:0]

CE#

OE#

WE#

DQ[14:0]

DQ[15]-A1 AOh PD DQ7# DOUT DOUT

Notes: 1. Only the third and fourth cycles of the PROGRAM command are represented. The PRO-

GRAM command is followed by checking of the status register data polling bit and by a

READ operation that outputs the data (DOUT) programmed by the previous PROGRAM

command.

2. PA is the address of the memory location to be programmed. PD is the data to be pro-

grammed.

3. DQ7 is the complement of the data bit being programmed to DQ7 (See Data Polling Bit

[DQ7]).

4. See the following tables for timing details: Read AC Characteristics, WE#-Controlled

Write AC Characteristics, and CE#-Controlled Write AC Characteristics.

128Mb 3V Embedded Parallel NOR Flash

Write AC Characteristics

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 67 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 30: CE#-Controlled Write AC Characteristics

Parameter

Symbol

60ns1

VCCQ = VCC

70ns

VCCQ = VCC

80ns

VCCQ = 1.65V to

VCC

UnitLegacy JEDEC Min Max Min Max Min Max

Address valid to next address valid tWC tAVAV 65 – 70 – 80 – ns

WE# LOW to CE# LOW tWS tWLEL 0 – 0 – 0 – ns

CE# LOW to CE# HIGH tCP tELEH 35 – 35 – 35 – ns

Input valid to CE# HIGH tDS tDVEH 45 – 45 – 45 – ns

CE# HIGH to input transition tDH tEHDX 0 – 0 – 0 – ns

CE# HIGH to WE# HIGH tWH tEHWH 0 – 0 – 0 – ns

CE# HIGH to CE# LOW tCPH tEHEL 30 – 30 – 30 – ns

Address valid to CE# LOW tAS tAVEL 0 – 0 – 0 – ns

CE# LOW to address transition tAH tELAX 45 – 45 – 45 – ns

OE# HIGH to CE# LOW – tGHEL 0 – 0 – 0 – ns

Note: 1. Only available upon customer request.

128Mb 3V Embedded Parallel NOR Flash

Write AC Characteristics

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 68 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Figure 23: CE#-Controlled Program AC Timing (8-Bit Mode)

AAAh PA PA

3rd cycle 4th cycle Data polling

tWC

tAS

tCP

tDS

tWHWH1

tCPH

tAH

tWS

tGHEL

tDH

tWH

A[22:0]/A-1

WE#

OE#

CE#

DQ[7:0] AOh PD DQ7# DOUT

Notes: 1. Only the third and fourth cycles of the PROGRAM command are represented. The PRO-

GRAM command is followed by checking of the status register data polling bit.

2. PA is the address of the memory location to be programmed. PD is the data to be pro-

grammed.

3. DQ7 is the complement of the data bit being programmed to DQ7 (See Data Polling Bit

[DQ7]).

4. See the following tables for timing details: Read AC Characteristics, WE#-Controlled

Write AC Characteristics, and CE#-Controlled Write AC Characteristics.

128Mb 3V Embedded Parallel NOR Flash

Write AC Characteristics

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 69 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Figure 24: CE#-Controlled Program AC Timing (16-Bit Mode)

555h PA PA

3rd cycle 4th cycle Data polling

tWC

tAS

tCP

tDS

tWHWH1

tCPH

tAH

tWS

tGHEL

tDH

tWH

A[22:0]

WE#

OE#

CE#

DQ[14:0]/A-1 AOh PD DQ7# DOUT

Notes: 1. Only the third and fourth cycles of the PROGRAM command are represented. The PRO-

GRAM command is followed by checking of the status register data polling bit.

2. PA is the address of the memory location to be programmed. PD is the data to be pro-

grammed.

3. DQ7 is the complement of the data bit being programmed to DQ7 (See Data Polling Bit

[DQ7]).

4. See the following tables for timing details: Read AC Characteristics, WE#-Controlled

Write AC Characteristics, and CE#-Controlled Write AC Characteristics.

128Mb 3V Embedded Parallel NOR Flash

Write AC Characteristics

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 70 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Figure 25: Chip/Block Erase AC Timing (8-Bit Mode)

AAAh

tWC

tAS

tWP

tDS

tWPH

tAH

tCS

tGHWL

tDH

tCH

A[22:0]/A-1

CE#

OE#

WE#

DQ[7:0] AAh

555h AAAh AAAh

BAh1

555hAAAh

55h 55hAAh80h 10h/

30h

Notes: 1. For a CHIP ERASE command, addresses and data are AAAh and 10h, respectively, while

they are BAd and 30h for a BLOCK ERASE command.

2. BAd is the block address.

3. See the following tables for timing details: Read AC Characteristics, WE#-Controlled

Write AC Characteristics, and CE#-Controlled Write AC Characteristics.

128Mb 3V Embedded Parallel NOR Flash

Write AC Characteristics

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 71 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Accelerated Program, Data Polling/Toggle AC Characteristics

Table 31: Accelerated Program and Data Polling/Data Toggle AC Characteristics

Parameter

Symbol

60ns1, 70ns,

80ns

UnitLegacy JEDEC Min Max

VPP/WP# rising or falling time – tVHVPP 250 – ns

Address setup time to OE# LOW during toggle bit poll-

ing

tASO tAXGL 10 – ns

Address hold time from OE# during toggle bit polling tAHT tGHAX, tEHAX 10 – ns

CE# HIGH during toggle bit polling tEPH tEHEL2 10 – ns

Output hold time during data and toggle bit polling tOEH tWHGL2, tGHGL2 20 – ns

Program/erase valid to RY/BY# LOW tBUSY tWHRL – 30 ns

Note: 1. Only available upon customer request.

Figure 26: Accelerated Program AC Timing

tVHVPP

VPPH

VIL or VIH

VPP/WP#

128Mb 3V Embedded Parallel NOR Flash

Accelerated Program, Data Polling/Toggle AC Characteristics

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 72 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Figure 27: Data Polling AC Timing

Data

Data High-Z

High-Z

DQ[6:0]

Output flag

DQ[6:0]

Valid data

tHZ/tDF

tOE

tCH

tBUSY

tOEH

CE#

OE#

WE#

DQ[6:0]

DQ7

RY/BY#

DQ7# DQ7

Valid data

tWHWH1/tWHWH2

Notes: 1. DQ7 returns a valid data bit when the PROGRAM or ERASE command has completed.

2. See the following tables for timing details: Read AC Characteristics, Accelerated Pro-

gram and Data Polling/Data Toggle AC Characteristics.

Figure 28: Toggle/Alternative Toggle Bit Polling AC Timing (8-Bit Mode)

Toggle Toggle ToggleData

Stop

toggling

Output

valid

tBUSY

tOEH tEPH

tOEH

CE#

WE#

OE#

DQ6/DQ2

RY/BY#

tOEH

tAHT tASO

tAHT

tDH

tAS

A[22:0]/A-1

tOE tE

Notes: 1. DQ6 stops toggling when the PROGRAM or ERASE command has completed. DQ2 stops

toggling when the CHIP ERASE or BLOCK ERASE command has completed.

2. See the following tables for timing details: Read AC Characteristics, Accelerated Pro-

gram and Data Polling/Data Toggle AC Characteristics.

128Mb 3V Embedded Parallel NOR Flash

Accelerated Program, Data Polling/Toggle AC Characteristics

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 73 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Program/Erase Characteristics

Table 32: Program/Erase Characteristics

Notes 1 and 2 apply to the entire table

Parameter Min Typ Max Unit Notes

Chip erase – 40 400 s 3

Block erase (128KB) – 0.5 2 s 4

Erase suspend latency time – 25 45 µs

Block erase timeout 50 – – µs

Byte program Single-byte program – 16 200 µs 3

Write to buffer program

(64 bytes at a time)

VPP/WP# = VPPH – 51 200 µs 3

VPP/WP# = VIH – 78 200 µs 3

Word program Single-word program – 16 200 µs 3

Write to buffer program

(32 words at a time)

VPP/WP# = VPPH – 51 200 µs 3

VPP/WP# = VIH – 78 200 µs 3

Chip program (byte by byte) – 270 800 s 3

Chip program (word by word) – 135 400 s 3

Chip program (write to buffer program) – 20 200 s 3, 5

Chip program (write to buffer program with VPP/WP# = VPPH) – 13 50 s 3, 5

Chip program (enhanced buffered program) – 8 40 s 5

Chip program (enhanced buffered program with VPP/WP# = VPPH) – 5 25 s 5

Program suspend latency time – 5 15 µs

PROGRAM/ERASE cycles (per block) 100,000 – – cycles

Data retention 20 – – years

Notes: 1. Typical values measured at room temperature and nominal voltages and for not cycled

devices.

2. Sampled, but not 100% tested.

3. Maximum value measured at worst case conditions for both temperature and VCC after

100,000 PROGRAM/ERASE cycles.

4. Block erase polling cycle time (see Data polling AC waveforms figure).

5. Intrinsic program timing, that means without the time required to execute the bus cy-

cles to load the PROGRAM commands.

128Mb 3V Embedded Parallel NOR Flash

Program/Erase Characteristics

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 74 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Package Dimensions

Figure 29: 56-Pin TSOP – 14mm x 20mm

0.1 A

See Detail A

56X 0.1 ±0.05

0.15 ±0.05

56X 0.22 ±0.05 14 ±0.1

18.4 ±0.1

20 ±0.2

1.1 ±0.1

0.5 TYP

Pin A1 ID

Detail A

Seating plane

0.6 ±0.1

0.25 gage plane

(0.1 ±0.05) A

Plating material composition: Ni/Pd/Au.

Plastic package material: epoxy novolac.

Package width and length include mold flash.

Notes: 1. All dimensions are in millimeters.

2. For the lead width value of 0.22 ±0.05, there is also a legacy value of 0.15 ±0.05.

128Mb 3V Embedded Parallel NOR Flash

Package Dimensions

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 75 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Figure 30: 64-Ball TBGA – 10mm x 13mm

BALL "A1"

0.10 MAX

0.50 TYP

1.00 TYP 0.80 TYP

1.20 MAX

1.50 TYP

3.00 TYP

0.50 TYP

7.00 TYP

10.00 ±0.10

13.00 ±0.10

0.35 MIN/

0.50 MAX

0.30 -0.10

+0.05

Note: 1. All dimensions are in millimeters.

128Mb 3V Embedded Parallel NOR Flash

Package Dimensions

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 76 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Figure 31: 64-Ball FBGA – 11mm x 13mm

Seating

plane

0.80 TYP

0.10

13.00 ±0.10

0.60 ±0.05

1.00

TYP

3.00

TYP

7.00 TYP

1.40 MAX

Ball A1 ID

1.00

TYP

2.00 TYP 0.48 ±0.05

11.00 ±0.10

7.00 TYP

64X

87654321

Note: 1. All dimensions are in millimeters.

128Mb 3V Embedded Parallel NOR Flash

Package Dimensions

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 77 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Revision History

Rev. C – 05/18

• Added Important Notes and Warnings section for further clarification aligning to in-

dustry standards

Rev. B – 05/15

• Updated TSOP package

Rev. A – 07/13

• Initial Micron brand release

8000 S. Federal Way, P.O. Box 6, Boise, ID 83707-0006, Tel: 208-368-4000

www.micron.com/products/support Sales inquiries: 800-932-4992

Micron and the Micron logo are trademarks of Micron Technology, Inc.

All other trademarks are the property of their respective owners.

This data sheet contains minimum and maximum limits specified over the power supply and temperature range set forth herein.

Although considered final, these specifications are subject to change, as further product development and data characterization some-

times occur.

128Mb 3V Embedded Parallel NOR Flash

Revision History

CCMTD-1725822587-2335

m29w_128mb.pdf - Rev. C 5/18 EN 78 Micron Technology, Inc. reserves the right to change products or specifications without notice.