VTC1 series Voltage Controlled Temperature Compensated Crystal Oscillator Features * Clipped Sine Wave or Square Wave Output * Output Frequencies to 40 MHz * Fundamental Crystal Design * Optional VCXO function available * Gold over nickel contact pads * Hermetically Sealed Ceramic SMD package The VTC1, VCTXCO * Product is compliant to RoHS directive and fully compatible with lead free assembly Applications * Wireless Communications * Base Stations * Point to point radios * Broadband Access * Test Equipment * Handsets Description Vectron's VTC1 Temperature Compensated Crystal Oscillator (TCXO) is a quartz stabilized, clipped sinewave output or CMOS squarewave, temperature compensated oscillator, operating off either 2.8, 3.0, 3.3 or 5.0 volt supply. Vectron International 267 Lowell Road, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com Performance Characteristics Table 1. Electrical Performance for the Clipped Sine Wave Output Option Parameter Symbol Min Typical Maximum Frequency fO 10.000 40.000 Typical Supply Voltage 2.8V, 3.0V, 3.3V or 5.0V Ordering option, see last page Supply Current IDD 10.000 MHz to < 15.000 MHz 1.5 15.000 MHz to < 26.00 MHz 2.0 26.000 MHz to 40.000 MHz 2.5 Output Level 2 Vp/p 0.8 Output Load 10K II 10pf Control Voltage Impedance ZVc 1 Control Voltage to reach pull All options (5.0, 3.3,3.0 and 2.8V) 0.5 2.5 Pull Range TPR 5, 8, 10, 15 or 20 Ordering option, see last page Temperature Stability 0.5 to 5.0 Ordering option, see last page. Initial Accuracy, "No Adjust" option 0.5 Power Supply Stability 0.2 Load Stability 0.2 Aging 1.0 Operating temperature 0/55, -10/60, -20/70, -30/80, -40/85 Ordering option, see last page Phase Noise, 12.800 MHz 10 Hz offset -85 100 Hz offset -115 1 kHz offset -130 10 kHz offset -143 100 kHz offset -152 Start-up time 2 Units MHz mA V Mohm V ppm ppm ppm ppm ppm ppm/year C dBc/Hz ms 1. A 0.01uF and a 0.1uF capacitor should be located as close to the supply as possible (to ground) is recommended. 2. Output is AC coupled. Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com VTC1 Data sheet Table 2. Electrical Performance for the CMOS Output Option Parameter Symbol Min Typical Maximum Frequency fO 10.000 40.000 Supply Voltage 3.3V10% Maximum Supply Voltage 7 Supply Current Output Level 2 Logic High Logic Low Drive High Drive Low Output Load Duty Cycle, @ 50% Control Voltage Impedance Control Voltage to reach pull Pull Range Ordering option, see last page Temperature Stability Ordering option, see last page. Initial Accuracy, "No Adjust" option Power Supply Stability Load Stability Aging Operating temperature Ordering option, see last page Phase Noise, 12.800MHz 10 Hz offset 100 Hz offset 1 kHz offset 10 kHz offset 100 kHz offset Start-up time IDD VOH VOL IOH IOL Units MHz VDC VDC 10.0 mA 0.1*VDD -4 V V mA mA 0.9*VDD 4 15pf 45/55 ZVc TPR 5, 8, 10 % Kohm V ppm 0.5 to 5.0 ppm 0.5 0.3 0.2 1.0 0/55, -10/60, -20/70, -30/80, -40/85 ppm ppm ppm ppm/year C 100 0.5 2.5 dBc/Hz -93 -123 -147 -155 -158 2 ms 1. A 0.01uF and a 0.1uF capacitor should be located as close to the supply as possible (to ground) is recommended. 2. Output is DC coupled. Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com VTC1 Data sheet Figure 1. Typical Phase Noise Plot, Clipped Sine Wave Figure 2. Clipped Sine Wave Output Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com VTC1 Data sheet VCXO Functional Description VCXO Feature: The VTC1 can be ordered with a VCXO function for applications were it will be used in a PLL, or the output frequency needs fine tune adjustments. This is high impedance, 1 Mohm, input and can be driven with an op-amp or terminated with adjustable resistors etc. Pin 1 should not be left floating on the VCXO optional devices. "No Adjust" Feature: In applications were the VTC1 will be not be used in a PLL, or the output frequency does not fine tune adjustments, the best device to use would be a VTC1-x0xxx. By using the "no adjust" option, the circuit is simplified as Vc does not need to adjusted or set to a predetermined voltage and pin 1 should be grounded or left open (but not set to a voltage such as the supply). Outline Diagrams, Pad Layout and Pin Out Table 3. Pinout Pin # Symbol 1 N/C or VC 2 GND 3 fO 4 VDD Function No Connect (VTC1-x0xx) or VCXO Control Voltage Electrical and Case Ground Output Frequency Supply Voltage NOTE: Additional pads are used to program and adjust the TCXO during manufacturing and should be left open; do not terminate these to the supply voltage. Some designs do not include these additional pads. Contact Pads are gold over nickel Figure 3, Package drawing Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com VTC1 Data sheet Tape and Reel Table 4. Tape and Reel Dimensions (mm) J F D G C B A L I E H Tape Dimensions Product A VTC1 16 B C D E 7.5 1.5 4 8 K Reel Dimensions F G H 1.5 20.2 13 I J K L 60 2 16.4 180 # Per Reel 1000 Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can permanently damage the device. Functional operation is not implied at these or any other conditions in excess of conditions represented in the operational sections of this data sheet. Exposure to absolute maximum ratings for extended periods may adversely affect device reliability. Table 5. Absolute Maximum Ratings Parameter Symbol Storage Temperature Tstorage Ratings -55/125 Unit C Reliability The VTC1 qualification tests have included: Table 6. Environnemental Compliance Parameter Mechanical Shock Mechanical Vibration Temperature Cycle Solderability Gross and Fine Leak Resistance to Solvents Vectron International 267 Lowell Rd, Hudson NH 03051 Conditions MIL-STD-883 Method 2002 MIL-STD-883 Method 2007 MIL-STD-883 Method 1010 MIL-STD-883 Method 2003 MIL-STD-883 Method 1014 MIL-STD-883 Method 2015 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com VTC1 Data Sheet Handling Precautions Although ESD protection circuitry has been designed into the the VTC1, proper precautions should be taken when handling and mounting. VI employs a Human Body Model and a Charged-Device Model (CDM) for ESD susceptibility testing and design protection evaluation. ESD thresholds are dependent on the circuit parameters used to define the model. Although no industry wide standard has been adopted for the CDM, a standard HBM of resistance = 1.5kohms and capacitance = 100pF is widely used and therefore can be used for comparison purposes. Table 7. ESD Ratings Model Human Body Model Charged Device Model Minimum 1000 1500 Conditions MIL-STD-883 Method 3115 JESD 22-C101 Suggested IR profile Devices are built using lead free epoxy and can also be subjected to standard lead free IR reflow conditions, Table 7 shows max temperatures and lower temperatures can also be used e.g. peak temperature of 220C. Table 8. Reflow Profile (IPC/JEDEC J-STD-020B) Parameter Symbol PreHeat Time tS Ramp Up R UP o Time Above 217 C Time To Peak Temperature Time At 260 oC (max) Time At 240 C (max) Ramp Down tL t AMB-P tP tp2 R DN Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 7 Value 150 sec Min, 200 sec Max 3 oC/sec Max 60 sec Min, 150 sec Max 480 sec Max 10 sec Max 60 sec Max 6 oC/sec Max e-mail vectron@vectron.com VTC1 Data Sheet Ordering Information Table 9. Standard Frequency List 10.000 10.0001355 10.001355 12.000 12.288 12.352 12.688375 12.800 13.000 14.5888 14.617188 14.7456 16.034950 16.320 16.3676 16.777216 16.800 17.500 19.200 19.440 19.680 21.250 22.000 22.368 25.000 25.48828 26.000 VTC1 - B 10.240 12.500 13.560 14.850 16.367667 18.000 19.800 23.090 32.000 0 10.245 12.504 14.000 15.000 16.36770 18.414 20.000 24.000 33.000 2 C 12.250 12.580 14.318 15.359865 16.384 18.432 20.250 24.5535 38.400 - 11.0592 12.582912 14.400 15.360 16.368 18.601 20.480 24.576 40.000 11.2896 12.600 14.500 16.000 16.580 19.000 20.91646 24.8064 10M000 Product Family Output Frequency TCXO, 5x7 In MHz Voltage Options Temperature Options A: +5.0 Vdc 5%, Clipped Sine Output A: 0 to 55C B: +3.3 Vdc 5%, Clipped Sine Output B: -10 to 60C C: +3.0 Vdc 5%, Clipped Sine Output C: -20 to 70C D: +2.8 Vdc 5%, Clipped Sine Output D: -30 to 80C J: +3.3 Vdc 10%, CMOS Output E: -40 to 85C Pulling Range 0: Fixed TCXO, no adjust Stability Options 1: 5ppm A: 0.5ppm 2: 8ppm 1: 1.0ppm 3: 10ppm B: 1.5ppm 4: 15ppm 2: 2.0ppm 5: 20ppm C: 2.5ppm 3: 3.0 ppm Note: Not all combinations are available: D: 3.5ppm 0.5 ppm is available over 0 to 55 C only 4: 4.0ppm 1.0 ppm to 5.0 ppm is available on all temperature ranges 5: 5.0ppm www.vectron.com USA: Vectron International * 267For Lowell Road, Hudson, NH 03051 Additional Information, Please Contact: * Tel: 1-88-VECTRON-1 * Fax: 1-888-FAX-VECTRON EUROPE: Landstrasse, D-74924, Neckarbischofsheim, Germany * Tel: 49 (0) 7268 8010 * Fax: 49 (0) 7268 801281 ASIA: Vectron Asia Pacific Sales 1F~2F. No.8 Workshop No.308 Fenju Rd., WaiGaoQiao Free Trade Zone, Pudong New Area Shanghai, China 200131 *Tel: 8621 50480777 * Fax: 8621 50481881 January 10, 2006 Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 8 e-mail vectron@vectron.com