CERAMIC HIGH-RELIABILITY GR900 SERIES & MIL-C-123 We = = CA PA Cl TORS CERAMIC HIGH RELIABILITY F-3054D 6/97KEMET CERAMIC HIGH RELIABILITY CAPACITORS CERAMIC HIGH RELIABILITY PRODUCTS Ceramic Chips, Radial Molded KEMET Electronics Corporation has been known for many years as the leader in the ceramic high relia- bility products. KEMET produces high reliability monolithic ceramic capacitors under tightly-con- trolled manufacturing procedures. These capacitors achieve State of the Art performance by virtue of careful materials selection, conservative design rules, motivational training of employees, and scrupulous inspection of all processes as well as the finished product. KEMET not only manufactures its own high reliability ceramic capacitor (GR900), KEMET also manufactures MIL-C-123 product which is built to the highest military standard in the industry today. BASIC REQUIREMENTS FOR KEMETS HIGH RELIABILITY PRODUCTS ARE AS FOLLOWS: 1. Selected Raw Materials: All raw materials are selected for characteristics known to produce the finest quality capacitors exhibiting the best electrical parameters and physical integrity. Materials trace- ability is maintained throughout the manufacturing process. 2. Batch Homogeneity: Production is under batch control. Each batch is homogeneous with respect to materials, design and processing conditions. 3. Clean Room Processing: All processes sensitive to particulate contamination take place in a clean room environment. 4. Special Designs: Special design considerations such as dielectric thickness are strictly enforced. Only COG (BP) and X7R (BX) temperature charac- teristics are made. 5. Destructive Physical Analysis (DPA, or Cross-Sectioning): All batches are sampled using EIA-469 as a minimum requirement. The samples remain on file and DPA Reports are shipped with the capacitors. 6. Ultrasonic Scanning: Optional 100% screening may be performed using ultrasonic waves to detect voids or delaminations. Screened lots must pass a final sample DPA. 7. Batch Performance Monitoring: All production batches are tested to generate electrical characteris- tics. Batches which show anomalous characteristics are rejected. 8. Special Customer Requirements: Many special requirements such as Serialization, DPA samples, X-Ray plates, and special packaging can be accom- modated. 9. Document Applicable: The high reliability prod- uct is implemented through various internal docu- ments under revision control. The Manufacturing Instructions provide detailed descriptions of all oper- ations and delineate requirements for process con- trol and product performance at various points in the process flow. Inspector Operating Documents describe test procedures and sampling plans for inspection of raw materials, in-process material and finished product. Raw material specifications describe physical and chemical characteristics as well as the packaging and labeling needed to pre- serve characteristics and identity. Customer specifi- cations are internal documents applicable only to products manufactured and inspected to require- ments of individual customers; in effect, these docu- ments translate customer drawings into modifica- tions of the specified portions of KEMET standard procedures. The Quality System in total is controlled by the KEMET Quality Manual and by various Quality Operating Documents. All documents, and revisions thereto, bear specified approval signatures. DETAILED SPECIFICATION: Temperature Characteristics Electrical stability with respect to temperature and voltage is related inversely to the packaging effi- ciency (capacitance X voltage in a given case size). COG (BP) is made from ceramic materials which are not ferroelectric, yielding superior stability but low packaging efficiency. X7R (BX) is made from materi- als which are ferroelectric, such as barium titanate, yielding a stable and high packaging efficiency. Aging If the temperature of a barium titanate dielectric is lowered after an excursion above its curie point, the ceramic crystalline structure gradually reverts to the tetragonal form typical of the low temperature condi- tions. The reversion requires a considerable length of time, and its effect in practical capacitors has become known as Aging. The rate of aging is affected by both the temperature and the applied voltage experienced by the capacitor. The COG (BP) formulation is non-ferroelectric and does not exhibit aging. The X7R (BX) formulation exhibits its own 2 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300CERAMIC HIGH RELIABILITY CAPACITORS characteristic aging rate which describes a decrease in capacitance versus time. The capacitance of the X7R dielectric decreases approximately 1.0% dur- ing each decade of hours following a return to tem- peratures below the curie point. In other words, capacitance will decrease 1.0% between 1 and 10 hours, another 1.0% between 10 and 100 hours, another 1.0% between 100 and 1000 hours, etc. KEMET takes into consideration the aging rate by designing capacitors to fall within the specified capacitance tolerance at 2400 hours. Inasmuch as the aging rate is exponential, very little change in capacitance will take place after 2400 hours. Voltage Effects Ferroelectric materials are also affected by applied voltage, both alternating and direct. Low values of voltage produce a slight increase in capacitance and dissipation factor. Higher voltages cause a decrease in capacitance. Typically, capacitors with X7R char- acteristic decrease in capacitance by approximately 10% when rated DC voltage is applied. Asmall portion of the decrease in capacitance by the application of a high DC voltage persists after the voltage is removed and then disappears gradually. Customer Testing Because of temperature and voltage effects, caution must be used in establishing a testing sequence for ceramic capacitors. Insulation resistance measure- ments and tests of dielectric withstanding voltage both require application of high DC voltage and cause temporary changes in capacitance. These tests, therefore, should not be conducted until capacitance testing is completed. Alternatively, the capacitors can be de-aged at high temperature as described above. A stabilization time at room ambi- ent of 24 hours should be used after de-aging. See F-3101 Catalog for more details. KEMET PERFORMANCE CHARACTERISTICS General Information Working Voltage: COG (BP) - 50,100 & 200 volts X7R (BX) - 50,100 & 200 volts Temperature Characteristics: COG (BP): 0 +30 ppm/C from -55C to +125C. (Limits widen below 20 pF.) X7R (BX): 415%; from -55C to +125C. Capacitance Tolerance: COG (BP): C - +0.25pF; D - +0.5pF; F - 11%; G- +2%; J- +5%; K- +10%; M- +20%. X7R (BX): J - +5%; K - 10%; M - +20%. Electrical Capacitance: Within specified tolerance when measured with 1 volt RMS @ 1 kHz (1000pF or less @ 1 MHz for COG (BP)). Dissipation Factor: 25C @ 1 kHz (1000 pF or less at 1 MHz for COG (BP)). COG (BP):0.15% maximum X7R (BX): 2.5% maximum Insulation Resistance: After 2 minutes electrification: at 25C and rated voltage: COG (BP):I00K megohms or (1000 megohm X uF), whichever is less. X7R (BX): |00K megohms or (1000 megohm X uF), whichever is less. at 125C and rated voltage: COG (BP):10K megohms or (100 megohm X pF), whichever is less. X7R (BX): 10K megohms or (100 megohm X pF), whichever is less. Dielectric Withstanding Voltage: 250% of rated voltage for 5 seconds with current limited to 50 MA at 25C. Aging Rate: % Delta Cap/Decade Hour, Typical COG (BP): 0% X7R (BX): 1.0% IMPORTANT NOTICE KEMET Electronics Corporation disclaims all warranties, whether express, implied, or statutory as to any manner whatso- ever, including the condition of the equipment, its compatibility with specific requirements, its merchantability, or fitness for any particular purpose which extend beyond the description on the face hereof. Furthermore, under no circumstances shall KEMET Electronics Corporation be liable for consequential, special, incidental or indirect damages resulting from the use or handling of this product. Finally, KEMET Electronics Corporation does not assume any responsibility for the correctness of the information contained in this catalog. All design characteristics, specifications, tolerances, and the like are subject to change without notice. KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300CERAMIC HIGH RELIABILITY CAPACITORS MIL-C-123/GR900 TYPICAL PERFORMANCE CURVES 0.20 +20 8.0 0.1 6.0 9 20 0.10 6 9 u a e 20 409 -0.1 -10 2.0 0.2 0.0 -55 -40 -20 0 20 40 60 80 100120 125 . 0 Temperature C -60 -40 -20 0 +20 +40 +60 *80 +100 +1200 - 140 Capacitance & DF vs. Temperature-COG Temperature C Capacitance & DF vs. Temperature-X7R 5 w 0 9 a g m 10 . DF 100 1K 10K 100K 1M 10M 1 0 Frequency-Hertz 100 1K 10K 100K 1M 10M Capacitance & DF vs. Frequency-COG FrequencyHertz Capacitance & DF vs. Frequency-X7R % 1 e +10 Q Oo @ +5 g 1 & a g & oO 5 1.000 7 | o 8 2 a -10 3 & 0.100 . E uw 4 ~ O83 5 2 0.010 g 1 0.1 1 10 100 . 0.001 AC or DC Volts Applied 0. 10.0 100.0 1000.0 Typical Effect of 1000 Hz AC and DC Voltage Level on FrequencyMHz Capacitance and Dissipation Factor X7R Impedance vs. Frequency For Ceramic Capacitors Note: COG Dielectric capacitance and dissipation factor X7R Dielectric are stable with voltage. 10.0 100.000 1 o 2 1.0 a 3 a a a E E 36 1.000 2 = t 0.1 QO 3 3 0.1 a E 0.01 0.01 0.1 1.0 10.0 100.0 1K 0.01 FrequencykHz Impedance vs. Frequency Characteristic-X7R Dielectric 0.001 0.1 1.0 10.0 Frequency MHz Impedance vs. Frequency for Ceramic CapacitorsC0G Dielectric 100.0 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 1K 29606, (864) 963-6300CERAMIC HIGH RELIABILITY MOLDED & CHIPS GENERAL INFORMATION MIL-C-123 INTRODUCTION MIL-C-123 specification covers the general requirements for high reliability, general purpose (BX) and temperature stable (BP) ceramic dielectric fixed capacitors for space, missile, and other high reliability applications. Capacitors covered by MIL-C-123 may be used in criti- cal frequency determining applications, timing circuits, and other applications where absolute stability is required (BP) and in applica- tions where appreciable variations in capacitance with respect to temperature, voltage, frequency, and life can be tolerated (BX). SCREENING TESTS Each lot has the following In-Process Inspections performed: 1. 100% Ultrasonic Scan 2. n-Process Destructive Physical Analysis 3. 100% visual inspection at a minimum of 10X magnification 4. Pre-encapsulation terminal strength evaluation (leaded devices only). Radial leaded capacitors must meet a minimum lead pull of 1.8 kg (4.0 lbs.). The following Group A shall be performed on each lot: 1. Thermal ShockPerformed in accordance to MIL-STD-202, Method 107, Condition A, with step 3 being 125C. Number of cycles shall be 20 (100% of lot). 2. Voltage ConditioningThe voltage conditioning shall consist of applying twice the rated voltage to the units at the maximum rated temperature of 125C for a minimum of 168 hours and a maximum of 264 hours. The voltage conditioning may be termi- nated at any time during 168 hours to 264 hours time interval that confirmed failures meet the requirements for the PDA dur- ing the last 48 hours listed in Table | below (100% of lot). Optional Voltage Conditioning (Accelerated Voltage Conditioning)All conditions of the standard voltage condi- tioning apply with the exception of the increased voltage and the decreased test time. (Refer to Mil-C-123 for formula.) *Step 5 is performed on chips at this point (100% of lot). 3. Dielectric Withstanding Voltage 250% of the dc rated voltage at 25C (100% of lot). 4. Insulation ResistanceThe 25C measurement with rated voltage applied shall be the lesser of 100,000 megohms or 1000 megohm-microfarads (100% of lot). *5 Insulation ResistanceThe 125C measurement with rated voltage applied shall be the lesser of 10,000 megohms or 100 megohm-microfarads (1000% of lot). For chips 125C IR is per- formed prior to step 3 above. 6. Capacitance must be within specified tolerance at 25C (100% of lot). Cap Exclusion: Capacitance values no more than 5% or .5 pF, whichever is greater, for BX characteristics or 1% or .3 pF, whichever is greater, for BP characteristics beyond specified tolerance limit shall be removed from the lot but shall not be con- sidered defective for determination of the PDA. 7. Dissipation Factor shall not exceed 2.5% for X dielectric, 0.15% for G dielectric at 25C (100% of lot). 8. Percent Defective Allowable (PDA). The following table lists the PDA requirements for MIL-C-123 Group A: TABLE | KEMET MIL BURN IN PDA PDA STYLE STYLE LAST 48 HOURS OVERALL C052Z CKSO05 1 unit or 0.1% 3% C062Z CKS06 1 unit or 0.2% 5% C5122 CKS07 1 unit or 0.2% 5% C0805Z CKS51 1 unit or 0.1% 3% C1210Z CKS52 1 unit or 0.1% 3% C1808Z CKS53 1 unit or 0.1% 3% C2225Z2 CKS54 1 unit or 0.1% 3% KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 aie 9. Radiographic Inspection (leaded devices only) (100% of lot). 10. Visual Inspection per MIL-C-123 criteria. 11. Destructive Physical Analysis per ElIA-469 and MIL-C-123. SAMPLE TESTS The following Group B tests shall be performed on samples from each lot, which have been subjected to and have passed Group A inspection. 1. Thermal ShockPerformed in accordance to MIL-STD-202, Method 107, Condition A, with step 3 being 125C. Number of cycles shall be 100. 2. Life Test per MIL-5TD-202, Method 108. Test temperature and tolerance is +125C +4, -0C. Capacitors shall be subjected to 2X rated voltage for 1000 hours. 3. Humidity, steady state, low voltage per MIL-STD-202, Method 103, Condition A. Capacitors shall be subjected to an environment of 85C with 85% relative humidity for 240 hours minimum. Cycling shall not be performed. A dec potential of 1.3 +0.25 volts shall be applied continuously through a 100,000 ohm resistance to each device under test. At completion, 25C IR and Cap are read. 4. Voltage-temperature limitsCapacitance is measured at var- ious temperatures (-55C to +125C) with and without rated voltage. 5. Moisture Resistance per MIL-STD-202, Method 106. There shall be 20 continuous cycles. During the first 10 cycles only, a de potential of 50 volts shall be applied across the capacitor ter- minals. Once each day, a check shall be performed to deter- mine whether a capacitor has shorted. Vibration cycle of MIL- STD-202, Method 106, Step 7b shall not be performed. Upon completion of MIL-STD-202, Method 106, Step 6 of the final cycle, capacitors shall be measured for capacitance, dielectric withstanding voltage and insulation resistance. The following Group C tests shall be performed on samples selected from lots that have passed Group A and have been submitted for Group B inspection. Samples shall be selected every two months. 1. Terminal Strength 2. Solderability 3. Resistance to Soldering Heat 4. Solvent Resistance (Leaded devices only) All lots shipped must have been subjected to and passed Group A and B testing. STANDARD PACKAGING FOR MIL-C-123 IS AS FOLLOWS: C052Z tray C0805Z chip tray C062Z tray C1210Z chip tray C5122 1 pe. per bag C1808Z chip tray C2225Z chip tray DATA PACKAGE A data package is sent with each shipment which contains: . Summary of Group A testing . Summary of Group B testing . Group B Variables Test Data . Lead Pull Data (Leaded Devices Only) . Final Destructive Physical Analysis Report . Certificate of Compliance stating that the ceramic capacitors supplied meet all the requirements of MIL-C-123, the applicable slash sheet(s) and all associated documents. Oahwhrd CERAMIC MOLDED/RADIAL MIL-C-123 GENERAL INFORMATION KEMET CAPACITOR OUTLINE DRAWINGS - (RADIAL LEADS) C052. jke-L >| ee C062, be & >| >| We A C512 K vl ly ; f .045 A Lead Dia. 1.25 | || Max. 1.25 || 025 | Center Line wn | Cente ine Min. |} s.002 | ertna a0" 015" of Center ot Center | | Line of case Y | | Line of case ee S| S>| DIMENSIONS INCHES & (MILLIMETERS) MILITARY s CASE | EQUIVALENT H L Ww LEAD SIZE STYLES HEIGHT LENGTH WIDTH SPACING C052 CKS05 190 + .010 (4.83 +.25) | .190+.010 (4.83+.25) | .090 +.010 (2.29+.25) | .200+.015 (6.08 + .38) C062 CKS06 290 + 010 (7.37 4.25) | .290+.010 (7.37425) | .090+.010 (2.29 + 25) | 200 +.015 (6.08 +.38) C512 CKS07 480 +.020 (12.19+.51) | 480+.020 (1219+ 51) | 140 +.010 (3.56 +.25)* | 400 + .020 (10.16 +.51) *0.200 maximum for some capacitance values. ORDERING INFORMATION KEMET PART NUMBER C052 Z 102 K5 GS5SCA CERAMIC __| | FAILURE RATE CASE SIZE AStandard Not applicable Radial LEAD MATERIAL co52 CStandard C062 Radial: solder coated copper C512 INTERNAL CONSTRUCTION SPECIFICATION 5Ultra-High Temperature Solder CAPACITANCE In picofarad code TEMPERATURE CHARACTERISTIC CAPACITANCE TOLERANCE Capacitance Change With Temp. Standard Without With Bias C +0.25 pF J 45% KEMET Military Temp. DC Bias (Rated) D +0.5 pF K H0% Designator Equivalent Range, C Voltage Voltage F 11% G WORKING VOLTAGE Stable 28 pomec | ppmrc _ oO x BX -55 to +15% +15% (Stable) +125 -25% 6 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300CERAMIC MOLDED/RADIAL MIL-C-123 (BP DIELECTRIC) aie MIL-C-123 MILITARY PART NUMBER M123 A O01 BX B 103 K C |___ TERMINATION Molded MILITARY C Solder-coated copper (radial) SPECIFICATION NUMBER TOLERANCE C+0.25pF J+5% 0, MODIFICATION LETTER Pathe #O% Indicates the latest characteristics ee of the part in the specification sheet. CAPACITANCE In picofarad code MIL-C-123 SLASH SHEET NUMBER VOLTAGE Slash KEMET Mil-C-123 B=50 C=100 Sheet # Style Style VOLTAGE-TEMPERATURE CHARACTERISTICS 01 C052 CKS05 Capacitance Change With Temp. 02 C062 CKS06 KEMET Military Temp. Witeat DG Bias (Rateay With Bias 03 C51 2 CKS07 Designator Equivalent Range, C Voltage Voltage (ira BP -55 to +30 +30 Stable) +125 ppm/C ppm/C x BX -55 to 415% +15% (Stable) +125 -25% RATINGS & PART NUMBER REFERENCE CAP. KEMET MIL-C-123 CAP. KEMET MIL-C-123 pF PART NUMBER PART NUMBER pF PART NUMBER PART NUMBER 100 VOLT - BP - C052 SIZE (MILITARY CKS05) 50 VOLT - BP - C052 SIZE (MILITARY CKS05) (Contd) 4.7 C0522479(1)1G5CA M123A01BPC4R7C 560 C0522561)5G5CA M123A01BPB561)C 51 C052251911)1G5CA M123A01BPC5R1(yC 620 C052262119)5G5CA M123A01BPB621)C 5.6 6052256911 GCA M123A01BPC5REWC 680 C0522681()5G5CA M123A01BPB681)C 6.2 6052262911 GSCA M123A01BPC6R2WC 750 C0522751()5G5CA M123A01BPB751@)C 6.8 6052268911 GSCA M123A01BPC6R8WC 820 C0522821(3)5G5CA M123A01BPB821)C 7.5 C052275911)1G5CA M123A01 BPC7R5wC 910 605229 11@)5G5CA M123A01BPB911(3)C 8.2 60522782911 GSCA M123A01BPC8R2W1C 1,000 605271 02)5G5CA M123A01BPB102a)C 9.4 6052291901 GS5CA M123A01BPC9R1(nC 1,100 C0522112a)5G5CA M123A01BPB112)C 10 C05221002)1G5CA M123A01BPC100@)C 1,200 605271 22)5G5CA M123A01BPB122)C 41 C05221102)1GSCA M123A01 BPC 110@)C 1,300 C052271323)5G5CA M123A01BPB132@)C 12 605221 202)1G5CA M123A01BPC1202)C 1,500 C05227152)5G5CA M123A01BPB152a)C 13 C05221302)1G5CA M123A01BPC1302)C 1,600 C05221 623)5G5CA M123A01BPB162a)C 15 C05221502)1G5CA M123A01BPC1502)C 1,800 605271 823)5G5CA M123A01BPB182a)C 16 C05271602)1G5CA M123A01BPC1602)C 2,000 C05222023)5G5CA M123A01BPB202)C 18 C05221802)1G5CA M123A01BPC1802)C 2,200 C05222221)5G5CA M123A01BPB222)C 20 C05222002)1G5CA M123A01 BPC2002)C 2,400 C05222423)5G5CA M123A01BPB242a)C 22 60522220211 GSCA M123A01 BPC2202)C 2,700 C05222723)5G5CA M123A01BPB272a)C 24 C05222402)1G5CA M123A01BPC240@1C 100 VOLT - BP - C062 SIZE (MILITARY CKS06) 27 C052227013)1 GSCA M123A01BPC27013)C 270 C062227113)1G5CA M123A02BPC27118)C 30 C0522Z30013)1 GSBCA M123A01BPC300i3)C 300 C062230113)1G5CA M123A02BPC301g)C 33 C052233013)1 GSCA M123A01BPC330(3)C 330 C062233113)1G5CA M123A02BPC331g)C 36 C052236013)1 GSCA M123A01BPC36013)C 360 C062236113)1G5CA M123A02BPC3613)C 39 C052239013)1 GSCA M123A01BPC390i3)C 390 C0622391(3)1G5CA M123A02BPC3913)C 43 C0522430i3)1 G5CA M123A01 BPC430g)C 430 C0622431(3)1G5CA M123A02BPC431 gC 47 C052247013)1 GSCA M123A01BPC470i3)C 470 C0622471(3)1 G5CA M123A02BPC471)C 51 C05225 1 013)1 GSCA M123A01BPC51013)C 510 C06225 111311 G5CA M123A02BPC511(3)C 56 C052256013)1 GSCA M123A01BPC560i3)C 560 C062256113)1G5CA M123A02BPC5618)C 62 C052262013)1 GSCA M123A01BPC62013)C 620 C062262113)1G5CA M123A02BPC62113)C 68 C052268013)1 GSCA M123A01BPC68013)C 680 C062268113)1G5CA M123A02BPC6813)C 75 C052275013)1 GSCA M123A01BPC750i3)C 750 C062275113)1G5CA M123A02BPC7518)C 82 C052282013)1 GSCA M123A01BPC82013)C 820 C062282113)1G5CA M123A02BPC82113)C 91 C052Z9 1 013)1 GSCA M123A01BPC911013)C 910 C062Z9 111311 G5CA M123A02BPC9 11(3)C 100 C05221018)1G5CA M123A01BPC101)3)C 1,000 C06221 0213)1 G5CA M123A02BPC1 02a)C 110 C052211118)1G5CA M123A01 BPC111@)C 1,100 C062211213)1G5CA M123A02BPC112(3)C 120 605221 2113)1G5CA M123A01BPC121)C 1,200 C06221 2213)1 G5CA M123A02BPC1 22)C 130 605221 3113)1 G5CA M123A01BPC131)C 1,300 C06221 3213)1 GSCA M123A02BPC132a)C 150 C05221513)1G5CA M123A01BPC15113)C 1,500 C06221 521311 G5CA M123A02BPC152a)C 160 C05221613)1G5CA M123A01BPC16113)C 1,600 C06221 6213)1 G5CA M123A02BPC1 62a)C 180 C05221 8113)1 G5CA M123A01BPC181)C 1,800 C06221 8213)1 G5CA M123A02BPC1 82a)C 200 C052220113)1G5CA M123A01BPC201,3)C 2,000 C062220213)1 G5CA M123A02BPC202a)C 220 C0522221(3)1 G5CA M123A01 BPC221(3)C 2,200 C062222213)1 GSCA M123A02BPC222)C 240 C0522241(3)1 G5CA M123A01BPC24113)C 2,400 C062224213)1 GSCA M123A02BPC242a)C 50 VOLT - BP - C052 SIZE (MILITARY CKS05) 50 VOLT - BP - C062 SIZE (MILITARY CKS06) 270 C05222713)5G5CA M123A01BPB271@C 2,700 C06222721)5G5CA M123A02BPB272)C 300 C0522Z3013)5G5CA M123A01BPB301)C 3,000 C0622302)5G5CA M123A02BPB302)C 330 C0522331(3)5G5CA M123A01BPB331@)C 3,300 C0622332)5G5CA M123A02BPB332)C 360 C05223613)5G5CA M123A01BPB361)C 3,600 C0622362)5G5CA M123A02BPB362)C 390 C05223913)5G5CA M123A01BPB391)C 3,900 C06223921)5G5CA M123A02BPB3928)C 430 C0522431(3)5G5CA M123A01BPB431@)C 4,300 C0622432)5G5CA M123A02BPB4328)C 470 C05224713)5G5CA M123A01BPB471@)C 4,700 C0622472()5G5CA M123A02BPB472)C 510 C0522511@)5G5CA M123A01BPB511@)C To complete the part numbers, insert the following tolerances: (1) C, +0.25pF; D. +0.5pF (2) C, +0.25pF; J, +5%; K, +10% (3) F, 41%; J, +5%; K, +10% KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300"4a laa CERAMIC MOLDED/RADIAL MIL-C-123 (BP/BX DIELECTRIC) RATINGS & PART NUMBER REFERENCE CAP. KEMET MIL-C-123 pF PART NUMBER PART NUMBER CAP. KEMET MIL-C-123 100 VOLT - BX - C052 SIZE (MILITARY CKS05) pF PART NUMBER PART NUMBER 270 C052Z271K1X5CA M123A01BXC271KC 00 VOLT - BX - C062 SIZE (MILITARY CKS06) 330 C052Z331K1X5CA M123A01BXC331 KC 5,600 C062Z562K1 X5CA M123A02BXC562KC 390 C052Z391K1X5CA M123A01BXC391 KC 6,800 C062Z682K1 X5CA M123A02BXC682KC 470 C052Z471K1X5CA M123A01BXC471KC 8,200 C062Z822K1 X5CA M123A02BXC822KC 560 C052Z561K1X5CA M123A01BXC561 KC 10,000 C062Z103K1 X5CA M123A02BXC103KC 680 C052Z681K1X5CA M123A01 BXC681 KC 12,000 C062Z123K1 X5CA M123A02BXC123KC 820 C052Z821K1X5CA M123A01BXC821 KC 15,000 C062Z153K1 X5CA M123A02BXC153KC 1,000 C052Z102K1X5CA M123A01BXC102KC 18,000 C062Z183K1 X5CA M123A02BXC183KC 1,200 C0527122K1X5CA M123A01BXC122KC 22,000 C062Z2223K1 X5CA M123A02BXC223KC 1,500 C052Z152K1X5CA M123A01BXC152KC 27,000 C062Z273K1 X5CA M123A02BXC273KC 1,800 C052Z7182K1X5CA M123A01BXC182KC 33,000 C062Z333K1 X5CA M123A02BXC333KC 2,200 C052Z222K1X5CA M123A01 BXC222KC 39,000 C062Z393K1 X5CA M123A02BXC393KC 2,700 C052Z272K1X5CA M123A01BXC272KC 47,000 C062Z473K1 X5CA M123A02BXC473KC 3,300 C052Z332K1X5CA M123A01 BXC332KC 56,000 C062Z563K1 X5CA M123A02BXC563KC 3,900 C052Z392K1X5CA M123A01 BXC392KC 68,000 C062Z683K1 X5CA M123A02BXC683KC 4,700 C052Z472K1X5CA M123A01BXC472KC 82,000 C062Z823K1 X5CA M123A02BXC823KC 50 VOLT - BX - C052 SIZE (MILITARY CKS05) 100,000 C0622104K1X5CA M123A02BXC104KC 5,600 C052Z562K5X5CA M123A01 BXB562KC 50 VOLT - BX - C062 SIZE (MILITARY CKS06) 6,800 C052Z682K5X5CA M123A01 BXB682KC 56,000 C062Z563K5X5CA M123A02BXB563KC. 8,200 C052Z822K5X5CA M123A01 BXB822KC 68,000 C062Z683K5X5CA M123A02BXB683KC. 10,000 C052Z7103K5X5CA M123A01BXB103KC 82,000 C062Z823K5X5CA M123A02BXB823KC. 100,000 C062Z104K5X5CA M123A02BXB104KC 120,000 C062Z124K5X5CA M123A02BXB124KC CAP. KEMET MIL-C-123 150,000 C062Z154K5X5CA M123A02BXB154KC pF PART NUMBER PART NUMBER 180,000 C062Z184K5X5CA M123A02BXB184KC 100 VOLT - BP - C512 SIZE (MILITARY CKS07) 220,000 C062Z2224K5X5CA M123A02BXB224KC 2,700 C512727218)1G5CA M123A03BPC272a1C 270,000 C062Z274K5X5CA M123A02BXB274KC 3,000 C5127302811G5CA M123A03BPC302a1C 330,000 C062Z334K5X5CA M123A02BXB334KC 3,300 C5127332811G5CA M123A03BPC332a1C 390,000 C062Z394K5X5CA M123A02BXB394KC 3,600 C51273621811G5CA M123A03BPC362a1C 470,000 C0622474K5X5CA M123A02BXB474KC 3,900 C51273921811G5CA M123A03BPC392a1C 560,000 C062Z564K5X5CA M123A02BXB564KC 4,300 C51274321)1G5CA M123A03BPC432a1C 680,000 C062Z684K5X5CA M123A02BXB684KC 4,700 C512Z74721811G5CA M123A03BPC472a1C 820,000 C062Z824K5X5CA M123A02BXB824KC 5,100 C5127512811G5CA M123A03BPC51 2a1C 1,000,000 C06221 05K5X5CA M123A02BXB105KC 5,600 05127562311 G5CA M123A03BPC562aC 6,200 C51276223)1G5CA M123A03BPC622aC 6,800 C51276823)1G5CA M123A03BPC682aC 7,500 C512775238)1G5CA M123A03BPC752aC CAP. KEMET MIL-C-123 8,200 C5122822)1G5CA M123A03BPC822C pF PART NUMBER PART NUMBER 9,100 C51279123)1G5CA M123A03BPC91 2a@C 00 VOLT - BX - C512 SIZE (MILITARY CKS07) 10,000 C512710381G5CA M123A03BPC103a@C 56,000 C512Z563K1 X5CA M123A02BXC563KC 50 VOLT - BP - C512 SIZE (MILITARY CKS07) 68,000 C512Z683K1 X5CA M123A02BXC683KC 11,000 C5127113@15G5CA M123A03BPB113@1C 82,000 C5122823K1XSCA M123A02BXC823KC 12,000 C512Z712315G5CA M123A03BPB1 231310 100,000 C5122104K1X5CA M123A02BXC104KC 13,000 C512Z7133@5G5CA M123A03BPB133131C 120,000 C5122124K1X5CA M123A02BXC124KC 15,000 C512Z153@5G5CA M123A03BPB153131C 150,000 C5122154K1X5CA M123A02BXC154KC 16,000 C512Z163@5G5CA M123A03BPB163131C 180,000 C5122184K1X5CA M123A02BXC184KC 18,000 C512Z7183@5G5CA M123A03BPB183131C 220,000 C512Z2224K1 X5CA M123A02BXC224KC 20,000 C512Z72035G5CA M123A03BPB203131C 270,000 C512Z2274K1 X5CA M123A02BXC274KC 22,000 C512722315G5CA M123A03BPB223131C 330,000 C5122334K1 X5CA M123A02BXC334KC 24,000 C512724315G5CA M123A03BPB243131C 390,000 C512Z2394K1 X5CA M123A02BXC394KC 27,000 C512Z7273@5G5CA M123A03BPB273131C 470,000 C5122474K1 X5CA M123A02BXC474KC 30,000 C51273038.5G5CA M123A03BPB3038)C 50 VOLT - BX - C512 SIZE (MILITARY CKS07) 33,000 C51273338.5G5CA M123A03BPB333g)C 560,000 C512Z564K5X5CA M123A02BXB564KC 36,000 C51273638.5G5CA M123A03BPB3638)C 680,000 C512Z684K5X5CA M123A02BXB684KC 39,000 C512739385G5CA M123A03BPB393a)C 820,000 C512Z824K5X5CA M123A02BXB824KC 43,000 C512743385G5CA M123A03BPB433a1C 1,000,000 C512Z105K5X5CA M123A02BXB105KC 47,000 C512747385G5CA M123A03BPB473a1C 51,000 0512751 385G5CA M123A03BPB513i31C To complete the part numbers, insert the following tolerances: (1) C, +0.25pF; 56,000 C512Z7563@15G5CA M123A03BPB5638)C D, +0.5pF (2) C, +0.25pF; J, +5%; K, 10% (3) F, 1%; J, +5%; K, 10% 62,000 C512762385G5CA M123A03BPB6238)C 68,000 C51276838.5G5CA M123A03BPB683)C 75,000 C512775385G5CA M123A03BPB753a1C 82,000 C512782335G5CA M123A03BPB8238)C 91,000 C512791385G5CA M123A03BPB913a1C 100,000 C51271045G5CA M123A03BPB1 041C MARKING INFORMATION C052Z C062Z, C512Z CAGE M123A MIL-C-123 M123A MIL-C-123 =. O2BPC | | Part Number Commercial and O01BPC | ;Part Number O71EC. | PAN? Government Entity 4R7CC JAN JAN JAN 271F Capacitance Code & Tolerance XXXX* | Date Lot Code OOO _ Date L Cod Vate Lot Coae 31433 CAGE 31433 CAGE KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300CERAMIC CHIP/MIL-C-123 CAPACITOR OUTLINE DRAWINGS CHIP DIMENSIONS "SOLDERGUARD I" "SOLDERGUARD II" 0.020 +0.010 \ (0.51 0.25) TERMINATIONS (METALLIZATION BANDS) SOLDER NK NICKEL an NICKEL ELECTRODES SILVER ELECTRODES SILVER METALLIZATION METALLIZATION TINNED Military Designation - "S" KEMET Designation - "H" Military Designation - "W" or "Y" KEMET Designation - "C" NOTE: For solder coated terminations, add 0.015 (0.38mm) to the positive width and thickness tolerances. Add the following to the positive length tolerance: CKS51 - 0.020 (0.51mm); CKS52, CKS53 and CKS54 - 0.025 (0.64mm); add 0.012 (0.30mm) to the bandwidth tolerance. DIMENSIONS INCHES MARKING Capacitors shall be legibly laser marked in contrasting color with either a three-digit capacitance code or KEMET trademark and 2-digit capacitance symbol. Termination C = Nickel Guarded, Tin Plated, H = Nickel Guarded, Solder-Coated (Solderguard II) (Solderguard |) Failure Rate (%/1000 Hours) A - Standard Not Applicable MILITARY T CHIP SIZE EQUIVALENT L WwW THICKNESS STYLES LENGTH WIDTH MAXIMUM 0805 CKS51 0.080+0.015 0.050+0.015 0.055 1210 CKS52 0.120+0.015 0.100+0.015 0.065 1808 CKS53 0.180+0.015 0.080+0.015 0.065 2225 CKS54 0.220+0.015 0.250+0.015 0.070 KEMET ORDERING INFORMATION 0805 2 101 K 5 GAG Ceramic Chip Size 0805, 1210, 1808, 2225 Specification Z Mil-C-123 Capacitance Picofarad Code Temperature Characteristic First two digits represent significant figures. KEMET Milita Tem Measured Without | Measured With Bias Third digit specifies number of zeros to follow. Designator Equivalent Range, C DC BiasVoltage (Rated Voltage) Capacitance Tolerance G 55 to 430 430 C +0.25pF J +5% (Ultra Stable) BP +125 ppm C ppm C D +0.5 pF K H0% F+1% x BX -55 to +15% +15% Working Voltage (Stable) +125 -25% 550 M123 A 10 BX B 472 K S we vgs as | Termination Military Specification W - Nickel Guarded, Tin; S - Nickel Guarded, Solder Number Tolerance Modification Number Indicates the latest characteristics of the part in the specification sheet. MIL-C-123 Slash Sheet Number Slash KEMET MIL-C-123 Sheet# Style Style 10 C0805 CKS51 11 C1210 CKS52 12 C1808 CKS53 13 C2225 CKS54 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 C - +0.25pF; D - +0.5pF; F - +1%; J - 5%; K - +10% Capacitance Picofarad Code Voltage B - 50 | Temperature Characteristic Capacitance Change with Temperature KEMET Military EIA Temp. Measured Without Measured With Bias Designator | Equivalent Equivalent Range, C DC BiasVoltage (Rated Voltage) G BP CoG -55 to +80 +30 (Ultra Stable) (NPO) +125 ppm C ppm C x BX X7R -55 to +H15% +15% (Stable) +125 -25%RATINGS AND PART NUMBER REFERENCE CERAMIC CHIP/MIL-C-123 (BP/BX DIELECTRIC) CAP. KEMET MIL-C-123 pF PART NUMBER PART NUMBER 50 VOLT - BP - C0805 SIZE (MILITARY CKS51) 1.0 C0805Z1 0911)5GAt4) M123A10BPB1 ROW 5) 1.1 C0805Z2119t5GAI4) M123A10BPB1 R115) 1.2 C0805Z12911)5GAt4) M123A10BPB1 R2t1y15) 1.3 C0805Z13911)5GAt4) M123A10BPB1 R315) 1.5 C0805Z15911)5GAt4) M123A10BPB1 R5t1y15) 1.6 C0805Z16911)5GAt4) M123A10BPB1 R6t1115) 1.8 C0805Z1 8911)5GAt4) M123A10BPB1 R81x15) 2.0 C0805Z20911)5GAt4) M123A10BPB2RO0x5) 2.2 C0805Z22911)5GAt4) M123A10BPB2R2t1y5) 2.4 C0805Z24911)5GAt4) M123A10BPB2R41t1115) 2.7 C0805Z27911)5GAt4) M123A10BPB2R71115) 3.0 C0805Z30911)5GAt4) M123A10BPB3RO0x5) 3.3 C0805Z3391)5GAt4) M123A10BPB3R30\5) 3.6 CO805Z36911)5GAt4) M123A10BPB3R6t1x15) 3.9 CO0805Z39911)5GAt4) M123A10BPB3R911x15) 4.3 C0805Z43911)5GAt4) M123A10BPB4R3015) 4,7 C0805247911)5GAt4) M123A10BPB4R71115) 5.4 C0805Z51 911)5GAt4) M123A10BPB5R 11115) 5.6 CO805Z56911)5GAt4) M123A10BPB5R611x15) 6.2 C0805Z62911)5GAt4) M123A10BPB6R211\15) 6.8 CO805Z68911)5GAt4) M123A10BPB6R8t1x15) 7.5 C0805Z7591)5GAt4) M123A10BPB7R5t1y15) 8.2 C0805Z82911)5GAt4) M123A10BPB8R2t1\15) 9.4 C0805Z91 911)5GAt4) M123A10BPB9R 11115) 10 C0805Z1 001a5GAt4) M123A10BPB100tex5) ah C0805Z1102)5GAi4) M123A10BPB 110125) 12 C0805Z1 201a5GAt4) M123A10BPB120tex5) 13 C0805Z1 301a5GAt4) M123A10BPB130tex5) 15 C0805Z1501a5GAt4) M123A10BPB150tex5) 16 C0805Z1 60ia5GAt4) M123A10BPB1601ex5) 18 C0805Z1 80125GAt4) M123A10BPB180tex5) 20 C0805Z200ia5GAt4) M123A10BPB200iex5) 22 C0805Z2201a5GAt4) M123A10BPB220iex5) 24 C0805Z2401a5GAt4) M123A10BPB240iex5) 27 C0805Z27013)5GAt4) M123A10BPB270i3x5) 30 C0805Z30013)5GAt4) M123A10BPB300i3x5) 33 C0805Z330i3)5GAt4) M123A10BPB33013x5) 36 C0805Z36013)5GAt4) M123A10BPB36013x5) 39 C0805Z39013)5GAt4) M123A10BPB39013x5) 43 C08052Z430i3)5GAt4) M123A10BPB430i3x5) 47 C0805Z47013)5GAt4) M123A10BPB470i3x5) 51 C0805Z51 013)5GAt4) M123A10BPB51013x5) 56 CO805Z560i3)5GAt4) M123A10BPB56013x5) 62 C0805Z62013)5GAt4) M123A10BPB620i3x5) 68 C0805Z680i3)5GAt4) M123A10BPB680i3x5) 75 C0805Z75013)5GAt4) M123A10BPB75013x5) 82 C0805Z82013)5GAt4) M123A10BPB820i3x5) 91 C0805Z91 013)5GAt4) M123A10BPB910i3x5) 100 C0805Z10113)5GAt4) M123A10BPB10113x5) 110 C0805Z1111)}5GAi4) M123A10BPB 11135) 120 C0805Z12113)5GAt4) M123A10BPB12113x5) 130 C0805Z13113)5GAt4) M123A10BPB13113x5) 150 C0805Z15113)5GAt4) M123A10BPB15113x5) 160 C0805Z16113)5GAt4) M123A10BPB16113x5) 180 C0805Z18113)5GAt4) M123A10BPB18113x5) 200 C08052Z20113)5GAt4) M123A10BPB201 3x5) 220 C0805222113)5GAt4) M123A10BPB22113x5) 240 C0805224113)5GAt4) M123A10BPB24 1135) 270 C0805Z27 113)5GAt4) M123A10BPB27113x9) 50 VOLT - BX - C0805 SIZE (MILITARY CKS51) 330 C08052Z331K5XAt4) M123A10BXB331 Kis) 390 C0805Z391 K5XAt4) M123A10BXB391 Kis) 470 C08052Z471K5XAt4) M123A10BXB471 Kis) 560 C0805Z561 K5XAt4) M123A10BXB561 Kis) 680 C0805Z681 K5XAt4) M123A10BXB681 Kis) 820 C0805Z821 K5XAt4) M123A10BXB821 Kis) 1,000 C0805Z102K5XAt4) M123A10BXB102Ki5) 1,200 C0805Z122K5XAi4) M123A10BXB122Ki5) 1,500 C0805Z152K5XAt4) M123A10BXB152Kis) 1,800 C0805Z182K5XAi4) M123A10BXB182Ki5) 2,200 C0805Z222K5XAt4) M123A10BXB222Ki5) 2,700 C0805Z272K5XAi4) M123A10BXB272Ki5) 3,300 C0805Z332K5XAt4) M123A10BXB332Ki5) 3,900 C0805Z392K5XAi4) M123A10BXB392Ki5) 4,700 C0805Z472K5XAt4) M123A10BXB472Ki5) 50 VOLT - BP - C1210 SIZE (MILITARY CKS52) 300 C1210Z301139)5GAt4) M123A11BPB301 3x5) 330 C1210Z33119)5GAt4) M123A11BPB331 3x5) 360 C1210Z36113)5GAt4) M123A11BPB361:3x5) 390 C1210Z39113)5GAt4) M123A11BPB391 3x5) 430 C1210Z431195GAt4) M123A11BPB43113x5) 470 C1210247113)5GA4) M123A11BPB47113x5) 510 C1210Z5111)5GA4) M123A11BPB5113x5) 560 C1210Z56113)5GAt4) M123A11BPB56113x5) 620 C1210Z62113)5GAt4) M123A11BPB62113x5) 680 C1210Z68113)5GAt4) M123A11BPB68 1135) 750 C1210Z75113)5GAt4) M123A11BPB75113x5) 820 C1210Z82113)5GAt4) M123A11BPB82113x5) 910 C12102Z9111)5GA4) M123A11BPB911:3x5) 1,000 C1210Z10213)5GAt4) M123A11BPB 102135) CAP. KEMET MIL-C-123 pF PART NUMBER PART NUMBER 50 VOLT - BX - C1210 SIZE (MILITARY CKS52) 5,600 C1210Z562K5XAM) M123A11BXB562Kis) 6,800 C1210Z682K5XAM) M123A11BXB682Kis) 8,200 C1210Z822K5XAM) M123A11BXB822Kis) 10,000 C1210Z103K5XAM) M123A11BXB103Ki5) 12,000 C1210Z123K5XAM) M123A11BXB123Ki5) 15,000 C1210Z153K5XAM) M123A11BXB153Ki5) 18,000 C1210Z183K5XAW) M123A11BXB183Ki5) 22,000 C1210Z223K5XAM) M123A11BXB223Ki) 27,000 C1210Z273K5XAW) M123A11BXB273Kio) 33,000 C1210Z333K5XAM) M123A11BXB333Kis) 47,000 C1210Z473K5XAW) M123A11BXB473Kis) 50 VOLT - BP- C1808 SIZE (MILITARY CKS53) 300 C1808Z30119)5GAM) M123A12BPB301 1315) 330 C1808Z33119)5GAM) M123A12BPB331 1315) 360 C1808Z36119)5GAM) M123A12BPB361 1315) 390 C1808Z39119)5GAM) M123A12BPB391 1315) 430 C1808Z43119)5GAM) M123A12BPB431 1315) 470 C1808Z47119)5GAM) M123A12BPB47 11315) 510 C1808Z511:95GAM) M123A12BPB5111316) 560 C1808Z56119)5GAM) M123A12BPB561 1315) 620 C1808Z62119)5GAM) M123A12BPB621 1315) 680 C1808Z68119)5GAM) M123A12BPB681 1315) 750 C1808Z7511s)5GAM) M123A12BPB751 1315) 820 C1808Z82119)5GAM) M123A12BPB821 1315) 910 C1808Z911195GAM) M123A12BPB911136) 1,000 C1808Z1021)5GAM) M123A12BPB 102035) 50 VOLT - BX- C1808 SIZE (MILITARY CKS53) 5,600 C1808Z562K5XAM) M123A12BXB562Kin) 6,800 C1808Z682K5XAM) M123A12BXB682Ki5) 8,200 C1808Z822K5XAM) M123A12BXB822Ki5) 10,000 C1808Z103K5XAM) M123A12BXB103Ki5) 12,000 C1808Z123K5XAM) M123A12BXB123Ki5) 15,000 C1808Z153K5XAM) M123A12BXB153Ki5) 18,000 C1808Z183K5XAM) M123A12BXB183Ki5) 22,000 C1808Z223K5XAM) M123A12BXB223Ki5) 27,000 C1808Z273K5XAM) M123A12BXB273Kio) 33,000 C1808Z333K5XAM) M123A12BXB333Ki5) 47,000 C1808Z473K5XAM) M123A12BXB473Ki5) 56,000 C1808Z563K5XAM) M123A12BXB563Ki5) 68,000 C1808Z683K5XAM) M123A12BXB683Ki5) 82,000 C1808Z823K5XAM) M123A12BXB823Ki5) 100,000 C1808Z104K5XAW) M123A12BXB104Ki5) 50 VOLT - BP- C2225 SIZE (MILITARY CKS54) 1,100 C2225Z11235GAM) M123A13BPB112i316) 1,200 C2225Z 12213)5GAM) M123A13BPB 1221315) 1,300 C2225Z13213)5GAM) M123A13BPB1321315) 1,500 C2225Z15213)5GA) M123A13BPB 1521315) 1,600 C2225Z 16213)5GAM) M123A13BPB 1621315) 1,800 C2225Z 18213)5GAM) M123A13BPB 1821315) 2,000 C2225Z20213)5GAM) M123A13BPB2021315) 2,200 C2225Z22213)5GAM) M123A13BPB2221315) 2,400 C2225Z24213)5GAM) M123A13BPB2421315) 2,700 C2225Z27213)5GAM) M123A13BPB2721315) 3,000 C2225Z30213)5GAM) M123A13BPB3021315) 3,300 C2225Z33213)5GAM) M123A13BPB3321315) 3,600 C2225Z36213)5GAM) M123A13BPB3621315) 3,900 C2225Z39213)5GAM) M123A13BPB3921315) 4,300 C2225Z43213)5GAM) M123A13BPB4321315) 4,700 C2225Z47213)5GAM) M123A13BPB4721315) 5,100 C2225Z51213)5GAM) M123A13BPB5121315) 5,600 C2225Z56213)5GAM) M123A13BPB5621315) 6,200 C2225Z62213)5GAM) M123A13BPB6221315) 6,800 C2225Z68213)5GAM) M123A13BPB6821315) 7,500 C2225Z75213)5GAM) M123A13BPB7521315) 8,200 C2225Z82213)5GAM) M123A13BPB8221315) 9,100 C2225Z91213)5GA) M123A13BPB91 21315) 10,000 C2225Z10313)5GA4) M123A13BPB10303x5) 50 VOLT - BX- C2225 SIZE (MILITARY CKS54) 120,000 C22252124KBXAM) M123A13BXB124Ki5) 150,000 C2225Z154K5XAW) M123A13BXB154Ki5) 180,000 C2225Z1B4K5XAM) M123A13BXB184Ki5) 220,000 C22252Z224K5XAM) M123A13BXB224Ki5) 270,000 C22252Z274K5XAW) M123A13BXB274Ki5) 330,000 C22252334K5XAW) M123A13BXB334Ki5) 390,000 C22252Z394KBXAM) M123A13BXB394Ki5) 470,000 C2225Z474KBXAW) M123A13BXB474Ki5) 10 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 To complete the part numbers, insert the following tolerances: (1) C, +0.25pF; D. +0.5pF (2) C, +0.25pF; J, +5%; K, +10% (3) F, 41%; J, +5%; K, 10% To complete part number, insert appropriate end metallization: KEMET: (4) C = Tin-Coated, FinalSolderGuard II H = Solder-Coated, FinalSolderguard | (5) W or Y = Tin-Coated, Final S = Solder-Coated, FinalCERAMIC HIGH RELIABILITY GENERAL INFORMATION GRSOO SERIES HIGH RELIABILITY GR900 GR800 capacitors are intended for use in any application where the chance of failure must be reduced to the lowest possible level. While any well-made multilayer ceramic capacitor is an inherently reliable device, GR900 capacitors receive special attention in all phases of manufacture including: Raw Materials Selection Special Designs Clean Room Production Individual Batch Testing Ultrasonic Scanning (when applicable) Singular Batch Identity is Maintained Destructive Physical Analysis These parts are well worth the added investment in comparison to the cost of a device or system failure. Typical applications include: 1. Medical: heart pacemakers, pain control devices, life signs monitoring, eyesight improvement and electroencephalographic equipment. 2. Aerospace: space exploration (Viking, Apollo, Venus Lander, etc.); Communications Satellites; Space Shuttle/IUS; Sky Lab. SCREENING AND SAMPLE TESTS Each batch receives the following testing/inspections: Preliminary: 1. Destructive Physical Analysis: (DPA) - Asample is pulled from each lot and examined per EIA-469 and KEMETs strict internal void and delamination criteria. Sampling plan is per MIL-C-123. 2. Ultrasonic Scanning - May be performed on batches failing to meet the DPA criteria for removal of marginal product. Not required on each lot. Group A 1. Thermal Shock Materials used in the construction of mul- tilayer ceramic capacitors possess various thermal coefficients of expansion. To assure maximum uniformity, each part is temper- ature cycled in accordance to MIL-STD-202, Method 107, Condition A with Step 3 being 125C. Number of cycles shall be 20 (100% of lot). 2. Voltage Conditioning One of the most strenuous environ- ments for any capacitor is the high temperature/high voltage test. All units are subject to twice-rated voltage to the units at the max- imum rated temperature of 125C for a minimum of 168 hours and a maximum of 264 hours. The voltage conditioning may be terminated at any time during 168 hours to 264 hours time inter- val that confirmed failures meet the requirements of the PDA dur- ing the last 48 hours of 1 unit or .4% (100% of lot). Optional Voltage Conditioning (Accelerated Voltage Conditioning) All conditions of the standard voltage condi- tioning apply with the exception of increased voltage and decreased test time. Refer to MIL-C-123 for the proper formula. *Step 5 is performed on chips at this point (100% of lot). 3. Dielectric Withstanding Voltage 250% of the de rated volt- age at 25C (100% of lot). 4. Insulation Resistance The 25C measurement with rated voltage applied shall be the lesser of 100,000 megohms or 1000 megohm-microfarads (100% of lot). *5. Insulation Resistance The 125C measurement with rated voltage applied shall be the lesser of 10,000 megohms or 100 megohm-microfarads (100% of lot). For chips, 125C IR is performed prior to Step 3 above. 6. Storage at 150C for 2 hours minimum without voltage applied followed by a 12-hour minimum stabilization period (temperature characteristic BX only). 7. Capacitance Shall be within specified tolerance at 25C (100% of lot). (Aging phenomenon is taken into account for BX dielectric to obtain capacitance.) 8. Dissipation Factor Shall not exceed 2.5% for X7R (BX) dielectric, 0.15% for NPO (BP) dielectric at 25C. (100% of lot.) 9. Percent Defective Allowable (PDA) The overall PDAis 8% for parts outside the MIL-C-123 values. The PDA is per MIL-C- 123 for all parts that are valid MIL-C-123 values. The PD includes steps 1 through 8 above with the following exceptions. Capacitance exclusion - capacitance values no more than 5% or .5pF, whichever is greater for BX characteristic or 1% or .3pF, whichever is greater for BP characteristic beyond specified toler- ance limit, shall be removed from the lot but shall not be consid- ered defective for determination of the PD. Insulation Resistance at 25C Product which is not acceptable for twice the military limit but is acceptable per the military limit, is removed from the lot but shall not be considered defective for determination of the PD. 10. Visual and Mechanical Examination Performed per MIL- C-123 criteria. 11. Radiographic Examination (Leaded Devices Only) Radial devices receive a one-plane X-ray. 12. Destructive Physical Analysis (DPA) A sample is exam- ined on each lot per EIA-469. Sampling Plan is per MIL-C-123. STANDARD PACKAGING All products are packaged in trays except C512 capacitors which are packaged 1 piece per bag. DATA PACKAGE A data package is sent with each shipment which contains: 1. Final Destructive Physical Analysis (DPA) report. 2. Certificate of Compliance stating that the parts meet all applic- able requirements of the appropriate military specification to the best failure level to which KEMET is approved. KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 11"dal loa CERAMIC MOLDED/RADIAL HIGH RELIABILITY GR900 SERIES CAPACITOR OUTLINE DRAWINGS C052 C062, C512 kK tL >| > |W ke A as Lead Dia. | | Max. 1 25 025 Center Line of | Center Line of Min. |) (4,002) |: leads within jeads within \ | .030" of Center | | 015 ot Center Line of case. DIMENSIONS INCHES & (MILLIMETERS) RADIAL LEAD CASE Hl L w LeAo STYLES SIZE HEIGHT LENGTH WIDTH SPACING MIL-C-20 MIL-C-39014 MIL-C-123 C052 | .190 + .010 (4.83 + .25) | 190 + .010 (4.83 + .25) | .090 + .010 (2.29 + 25) | .200+.015 (5.08 + .38) CCRO5 CKRO5S CKS05 C062 | .290 + .010 (7.37 + .25) | 290 + .010 (7.37 + .25) | .090 + .010 (2.29 + 25) | 200+ .015 (5.08 + .38) CCRO6 CKRO6 CKS06 C512 | .480 + .020 (12.19 + 51) | 480 + .020 (12.19 + .51)| .140 + .010 (3.56 + .25) | 400 + .020 (10.16 + .51) CCRO7 _ CKS07 C 052 B 223 K1X5CA MONOLITHIC a L FAILURE RATE CERAMIC AStandard Not Applicable CAPACITORS PHYSICAL DIMENSIONS LEAD MATERIAL (See above) C Standard Radial: solder coated copper HIEREL SPECIFICATIONS INTERNAL CONSTRUCTION B Leaded devices 5 Ultra-High Temperature Solder APACITANCE PICOFARAD CODE TEMPERATURE cA two cit are CE PICOFA of AD Col value and third CHARACTERISTICS digit is the number of zeros to follow in stating capacitance in pico- (See table below) farads. For example, 223 is 22,000 pF. The third-digit number 9 indicates a divisor of 10; for example, 229 is 2.2 pF. RATED VOLTAGE CAPACITANCE TOLERANCE 2 200 +20% G +2% (G(BP) Temperature Characteristic Only) 5 50 K 1i10% F+1% (G(BP) Temperature Characteristic Only) J +5% *D+0.5 pF (G(BP) Temperature Characteristic Only) *C+0.25 pF (G(BP) Temperature Characteristic Only) *These tolerances available only for 1.0 through 9.1 pF capacitors. TEMPERATURE CHARACTERISTICS CAPACITANCE CHANGE WITH TEMPERATURE -55 TO +125C PART NUMBER WITHOUT D.C. WITH RATED D.C. OTHER NOMENCLATURE LETTER BIAS VOLTAGE APPLIED EIA MILITARY COMMON G +30ppm/C +30ppm/C COG CG,BP NPO Xx +15% +15%, -25% X7R BX _ 12 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300CERAMIC MOLDED/RADIAL HIGH RELIABILITY KEMET GR900 SERIES (BP DIELECTRIC) CAPACITOR MARKINGS Size (C052 or C062) as applicable C052 KEMET Ls KEMET 200V r Voltage C512BG | Size, B = GR900, Temperature K= KEMET, B = GR900 Spec, KBG Characteristic (G = NPO, X = X7R) Temperature Characteristic, XXXX r~ Date Code | 194), 100v |- Capacitance Code, Tolerance, Voltage (G = NPO, X = X7R) r~ Lot Code XXXX** L Date Code & Lot Code Capacitance Code, Tolerance S 101J RATINGS & PART NUMBER REFERENCE CAPACITANCE KEMET CAPACITANCE KEMET pF PART NUMBER pF PART NUMBER 200 VOLT - BP - STYLE C052 200 VOLT - BP - STYLE C052 (Cont'd) 1.0 C052B10942G5CA 33.0 C052B330142G5CA 1.1 C052B119142G5CA 36.0 CO052B360142G5CA 1.2 C052B1294)2G5CA 39.0 CO052B39014#2G5CA 1.5 C052B1594)2G5CA 43.0 C052B430142G5CA 1.8 C052B18942G5CA 47.0 C052B470142G5CA 2.0 CO052B2094)2G5CA 51.0 C052B510142G5CA 2.2 CO052B2294)2G5CA 56.0 CO52B560142G5CA 2.4 C052B2494)2G5CA 62.0 CO052B620142G5CA 2.7 C052B27942G5CA 68.0 CO052B680142G5CA 3.0 CO052B30942G5CA 75.0 C052B750142G5CA 3.3 CO052B33942G5CA 82.0 CO052B820142G5CA 3.6 CO052B3694)2G5CA 91.0 C052B91014#2G5CA 3.9 CO052B3994)2G5CA 100 C052B101142G5CA 4.3 C052B4394)2G5CA 110 C052B111142G5CA 4.7 C052B47942G5CA 120 C0528121142G5CA 5.1 C052B5194)2G5CA 130 C0528131142G5CA 5.6 CO52B5694)2G5CA 150 C052B151142G5CA 6.2 CO052B6294)2G5CA 160 C052B161142G5CA 6.8 CO052B6894)2G5CA 180 C052818142G5CA 75 C052B7594)2G5CA 200 C0528201412G5CA 8.2 CO052B8294)2G5CA 220 C052B221142G5CA 9.1 C052B9194)2G5CA 240 C052B241142G5CA 10.0 C052B100M)2G5CA 270 C052B271142G5CA 11.0 C052B110142G5CA 300 C0528301412G5CA 12.0 C052B12042G5CA 330 C052B331142G5CA 13.0 C052B130M2G5CA 360 C0528361412G5CA 15.0 C052B1504)2G5CA 390 C052B391142G5CA 16.0 C052B1604)2G5CA 430 C052B431142G5CA 18.0 C052B1804)2G5CA 470 C052B471142G5CA 20.0 CO052B200H2G5CA 510 C052B511142G5CA 22.0 C052B22042G5CA 560 C052B561142G5CA 24.0 C052B24042G5CA 620 C052B621142G5CA 27.0 C052B27042G5CA 680 C052B681142G5CA 30.0 C052B30042G5CA 750 C052B751142G5CA (1) Complete KEMET part number by inserting capacitance tolerance, as applicable as shown in ordering information on page 12 BP CAPACITANCE TOLERANCE: 11%, +2%, +5%, +10%, 20% (+0.5pF & +0.25pF tolerances available 1.0 thru 9.1pF only) TEMPERATURE CHARACTERISTIC G BX CAPACITANCE TOLERANCE: +5%, +10%, +20% TEMPERATURE CHARACTERISTIC Xx (2) Capacitance values shown above are standard. Other capacitance values are available upon request. KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 13CERAMIC MOLDED/RADIAL HIGH RELIABILITY GR 900 SERIES (BP/DX DIELECTRIC) RATINGS & PART NUMBER REFERENCE CAPACITANCE KEMET CAPACITANCE KEMET pF PART NUMBER pF PART NUMBER 200 VOLT - BP - STYLE C052 (Contd) 200 VOLT - BP - STYLE C062 (Contd) 820 CO052B821i2G5CA 560 C062B561112G5CA 910 C052B911(n2G5CA 620 C062B621112G5CA 1000 C052B102W)2G5CA 680 C062B681112G5CA 1100 C052B112W2G5CA 750 C062B751(2G5CA 1200 C052B1220)2G5CA 820 C062B821112G5CA 1300 C052B132u)2G5CA 910 C062B9111W2G5CA 1500 C052B152W2G5CA 1000 C062B1020)2G5CA 100 VOLT - BP - STYLE C052 1100 C062B112W2G5CA 1600 C052B1621111G5CA 1200 C062B1220\2G5CA 1800 C052B1821)1G5CA 1300 C062B132i)2G5CA 2000 C052B2021)1G5CA 1500 C062B152i)2G5CA 2200 C052B22211)1G5CA 1600 C062B1620)2G5CA 2400 C052B2420111G5CA 1800 C062B18212G5CA 2700 C052B2720)1G5CA 2000 C062B202i12G5CA 3000 C052B302)1G5CA 2200 C062B222i)2G5CA 3300 C052B332u)1G5CA 2400 C062B242.n2G5CA 3600 C052B362i111G5CA 2700 C062B27212G5CA 3900 C052B392u)1G5CA 3000 C062B302i12G5CA 4300 C052B432)1G5CA 3300 C062B332i12G5CA 4700 C052B4720)1G5CA 3600 C062B362012G5CA 5100 C052B5121111G5CA 3900 C062B39212G5CA 5600 C052B562i1)1G5CA 4700 C062B472i12G5CA 200 VOLT - BX - STYLE C052 5100 C062B512u)2G5CA 470 C052B471002X5CA 5600 C062B562012G5CA 560 C052B56112X5CA 6200 C062B6220)2G5CA 680 C052B68112X5CA 6800 C062B6820)2G5CA 820 C052B82112X5CA 100 VOLT - BP - STYLE C062 1000 C052B1021)2X5CA 7500 C062B752)1G5CA 1200 C052B1221)2X5CA 8200 C062B8221111G5CA 1500 C052B152W12X5CA 9100 C062B9 121111 G5CA 1800 C052B1820)2X5CA 10,000 C062B103i)1G5CA 2200 C052B2220)2X5CA 11,000 C062B113111G5CA 2700 C052B272u0)2X5CA 12,000 C062B1231111G5CA 3300 C052B332u1)2X5CA 13,000 C062B133111G5CA 3900 C052B3920)2X5CA 15,000 C062B153i)1G5CA 4700 C052B472u0)2X5CA 16,000 C062B163i)1G5CA 5600 C052B562u)2X5CA 18,000 C062B1831G5CA 6800 C052B68211)2X5CA 20,000 C062B203111 G5CA 8200 C052B8220)2X5CA 22,000 C062B223i)1G5CA 10,000 C052B103u2X5CA 200 VOLT - BX - STYLE C062 12,000 C052B123W2X5CA 3300 C062B332W2X5CA 15,000 C052B15302X5CA 3900 C062B392W12X5CA 100 VOLT - BX - STYLE C052 4700 C062B4721112X5CA 18,000 C052B1831)1X5CA 5600 C062B5620)2X5CA 22,000 C052B223111 X5CA 6800 CO062B6820)2X5CA 27,000 C052B273i1 X5CA 8200 CO062B8220)2X5CA 33,000 C052B333i11 X5CA 10,000 C062B103m2X5CA 39,000 C052B393i11 X5CA 12,000 C062B123W)2X5CA 47,000 C052B4731X5CA 15,000 C062B153W2X5CA 50 VOLT - BX - STYLE C052 18,000 C062B183i2X5CA 56,000 CO52B563u15X5CA 22,000 C062B223112X5CA 68,000 CO52B6835X5CA 27,000 C062B273u12X5CA 82,000 C052B8231)5X5CA 33,000 C062B333iN2X5CA 100,000 C052B1041)5X5CA 39,000 C062B393i2X5CA 120,000 C052B124)5X5CA 47,000 C062B473u2X5CA 150,000 C052B15415X5CA 56,000 CO62B56312X5CA 200 VOLT - BP - STYLE C062 68,000 CO62BE832X5CA 330 C062B33102G5CA 100 VOLT - BX - STYLE C062 360 C062B361112G5CA 82,000 C062B8231111 X5CA 390 C062B391112G5CA 100,000 C062B104i1)1 X5CA 430 C062B431112G5CA 120,000 C062B 1241111 X5CA 470 C062B471W2G5CA 150,000 C062B15411)1X5CA 510 C062B51112G5CA 180,000 C062B 1841111 X5CA 220,000 C062B224i1)\1 X5CA (1) Complete KEMET part number by inserting capacitance tolerance, as applicable as shown in ordering information on page 12. BP CAPACITANCE TOLERANCE: 41%, +2%, +5%, 410%, +20% (+0.5pF & +0.25pF tolerances available 1.0 thru 9.1pF only) TEMPERATURE CHARACTERISTIC G BX CAPACITANCE TOLERANCE: +5%, 110%, +20% TEM- PERATURE CHARACTERISTIC X (2) Capacitance values shown above are standard. Other capacitance values are available upon request. 14 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300CERAMIC MOLDED/RADIAL HIGH RELIABILITY GR 900 SERIES (BP/DX DIELECTRIC) RATINGS & PART NUMBER REFERENCE CAPACITANCE KEMET pF PART NUMBER 200 VOLT - BX - STYLE C512 39,000 C512B3932X5CA 47,000 C512B473m2X5CA 56,000 C512B563i2X5CA 68,000 C512B683W2X5CA 82,000 C512B823i)2X5CA 100,000 C512B104i2X5CA 120,000 C512B124i2X5CA 150,000 C512B154i2X5CA 180,000 C512B184i2X5CA 220,000 C512B224i2X5CA 270,000 C512B274i2X5CA 330,000 C512B334i2X5CA 390,000 C512B394in2X5CA 100 VOLT - BX - STYLE C512 470,000 C512B474i)1 X5CA 560,000 C512B564i1)1 X5CA 680,000 C512B684i1)1 X5CA 820,000 C512B8241111 X5CA 1,000,000 C512B1051X5CA 50 VOLT - BX - STYLE C512 1,200,000 C512B125u)5X5CA 1,500,000 C512B155u15X5CA 2,000,000 C512B205u5X5CA 2,200,000 C512B225)5X5CA 3,300,000 C512B335u)5X5CA CAPACITANCE KEMET pF PART NUMBER 50 VOLT - BX - STYLE C062 270,000 C062B274015X5CA 330,000 C062B334i)5X5CA 390,000 C062B394)5X5CA 470,000 C062B4740)5X5CA 560,000 C062B5641115X5CA 680,000 C062B68411)5X5CA 820,000 C062B8241)5X5CA 1,000,000 C062B1050)5X5CA 200 VOLT - BP- STYLE C512 2000 C512B2020)2G5CA 2200 C512B22202G5CA 2400 C512B24202G5CA 2700 C512B27202G5CA 3000 C512B30202G5CA 3300 C512B332W2G5CA 3600 C512B362W2G5CA 3900 C512B392W2G5CA 4300 C512B432u)2G5CA 4700 C512B472W2G5CA 5600 C512B56202G5CA 6800 C512B682W2G5CA 8200 C512B8220)2G5CA 10,000 C512B103W2G5CA 12,000 C512B123W2G5CA 15,000 C512B153W2G5CA 18,000 C512B1830)2G5CA 22,000 C512B223W2G5CA 27,000 C512B273W2G5CA 33,000 C512B333W2G5CA 100 VOLT - BP- STYLE C512 39,000 C512B3930)1G5CA 47,000 C512B473W2G5CA 56,000 C512B5630)1G5CA 68,000 C512B6830)1G5CA 82,000 C512B8230)1G5CA 100,000 C512B1040)1G5CA 50 VOLT - BP- STYLE C512 120,000 C512B1240)5G5CA 150,000 C512B154)5G5CA (1) Complete KEMET part number by inserting capacitance tolerance, as applicable as shown in ordering information on page 12. BP CAPACITANCE TOLERANCE: 41%, +2%, +5%, +10%, 420% (+0.5pF & +0.25pF tolerances available 1.0 thru 9.1pF only) TEMPERATURE CHARACTERISTIC G BX CAPACITANCE TOLERANCE: +5%, +10%, +20% TEMPERATURE CHARACTERISTIC xX (2) Capacitance values shown above are standard. Other capacitance values are available upon request. KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 15CERAMIC CHIPS HIGH RELIABILITY GR 900 SERIES (BP/DX DIELECTRIC) CAPACITOR OUTLINE DRAWINGS CHIP DIMENSIONS "SOLDERGUARD I * SOLDERGUARD II" Re SOLDER TINNED a WO oo v oa T 51 + .25 7 {.020 + .010) t w an NICKEL Ss | ELECTRODES SILVER ELECTRODES SILVER METALLIZATION METALLIZATION * Add .38mm (.015) to the positive width and thickness tolerance dimensions and .64mm (.025) to the positive length tolerance dimension for Solderguard I. DIMENSIONS MILLIMETERS (INCHES) T Size L Ww Thickness Code Length Width Max. 0805 | 2.03 (.080) + 0.38 (.015) | 1.27 (. a) + 0.38 (.015) 1.4 (.055) 1005 | 2.56 (.100) + 0.38 (.015) | 1.27 (.050) + 0.38 (.015) 1.5 (.059) 1206 | 3.07 (.120) + 0.38 (.015) | 1.52 (.060) + 0.38 (.015) 1.6 (.065) 1210 | 3.07 (.120) + 0.38 (.015) | 2.56 (.100) + 0.38 (.015) 1.6 (.065) 1805 | 4.57 (.180) + 0.38 (.015) | 1.27 (.050) + 0.38 (.015) 1.4 (.055) 1808 | 4.57 (.180) + 0.38 (.015) | 2.03 (.080) + 0.38 (.015) 1.6 (.065) 1812 | 4.57 (.180) + 0.38 (.015) | 3.18 (.125) + 0.38 (.015) 2.03 (.080) 1825 | 4.57 (.180) + 0.38 (.015) | 6.35 (.250) + 0.38 (.015) 2.03 (.080) 2225 | 5.59 (.220) + 0.38 (.015) | 6.35 (.250) + 0.38 (.015) 2.03 (.080) ORDERING INFORMATION K 5X A C C 0805 A 103 CERAMIC SIZE CODE See table above SPECIFICATION A KEMET GR900 (CHIPS) CAPACITANCE CODE Expressed in Picofarads (pF) First two digit-significant figures. Third digit-number of zeros. (Use 9 for 1.0 thru 9.9 pF. Example: 2.2 pF 229). CAPACITANCE TOLERANCE M+20% G +2% (G(BP) Temperature Characteristic Only) K+H0% F+1% (G(BP) Temperature Characteristic Only) J +45% *D +0.5 pF (G(BP) Temperature Characteristic Only) *C +0.25 pF (G(BP) Temperature Characteristic Only) *These tolerances available only for 1.0 through 10 pF capacitors. VOLTAGE 1100 2200 550 L END METALLIZATION CTin-Coated, Final (SolderGuard II) HSoder-Coated, Final (SolderGuard 1) FAILURE RATE LEVEL (%/1,000 HOURS) AStandardNot applicable TEMPERATURE CHARACTERISTIC Designated by Capacitance Change over Temperature Range GBP (+30 PPM/C) XBX (15%, +15%, -25% with bias.) 16 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300CERAMIC CHIPS HIGH RELIABILITY GR 900 SERIES (BP/DX DIELECTRIC) RATINGS AND PART NUMBER REFERENCE STYLE C0805 CAPACITANCE KEMET CAPACITANCE KEMET pF PART NUMBER pF PART NUMBER 200 VOLT - BP 200 VOLT - BX 1.0 C0805A1 09(N2GAG) 180 C0805A181(N2XAl2) 14 C0805A1191)2GA2) 220 C0805A221(N2XAl2) 1.2 CO0805A1 29(N2GAG) 270 C0805A271(N2XAl2) 1.5 C0805A1 59(N2GAG) 330 C0805A331(N2XAl2) 1.6 CO0805A1 69(N2GAG) 390 C0805A391(N2XAl2) 1.8 C0805A1 89(N2GAG) 470 C0805A471(N2XAl2) 2.0 CO805A209(N2GAG) 560 CO805A561(N2XAl2) 2.2 CO805A229(N2 GAG) 680 CO0805A681(N2XAl2) 2.4 CO805A249(N2 GAG) 820 C0805A821(N2XAl2) 27 CO805A279112GA2) 100 VOLT - BX 3.0 COB0SASO9LN2GAZ) 7000 COB805A1 021 XA) 3.3 COB0SAS391N2GAZ) 1200 CO805A1 22111 XA) 3.6 COB0SASE9LN2ZGALZ) 1500 CO805A1 5211 XA) 3.9 COB0SAS99IN2GALZ) 1800 CO805A1 821111 XA) 43 COB0SA4391N2GA2} 2200 COB805A222111 XA) 47 COB0SA4791N2GA2) 2700 C0805A27211 XA2) 5.1 COB0SAS1912GA2) 3300 CO805A332111 XAI2) 5.6 COB0SASB92GA2) 3900 CO805A3921111 XAI2) 8.2 COB0SAG2912GA2) 4700 C0805A472(N1 XAI2) 75 COS0SA7S9I2GAR: 50 VOLT - BX 82 CO805A8291112 GA) 5600 CO805A562(N5XAL2) 94 C0805A91 9112GA2) 6800 CO805A682(N5XAL2) 10.0 C0805A1 00112GA2) 8200 CO805A8B22(N5XAL2) 11.0 C0805A11 012GA2) 10,000 CO0805A1 O3(5XAl2) 12.0 CO0805A1 20112 GAG) eo conoLa compa AEs (1) Complete KEMET part number by inserting capacitance 16.0 CO805A1 60U112GAQI tolerance, as applicable as shown in ordering information on 18.0 CO805A1 80112 GAZ) page 16. 20.0 COB805A2 001112 GAL2) BP CAPACITANCE TOLERANCE: +1%, +2%, +5%, +10%, 22.0 CO805A22011)2 GAZ) +20% (+0.5pF & +0.25pF tolerances available 1.0 thru 10pF 24.0 CO0805A24012GAG) only) TEMPERATURE CHARACTERISTIC G 27.0 CO805A2700)2GAG) BX CAPACITANCE TOLERANCE: +5%, +10%, +20% TEM- ae ene eeenrectnnt PERATURE CHARACTERISTIC xX 360 COB05A3601112 GALI (2) Complete part number by inserting end Metallization, as 39.0 CO805A390112GA2) applicable as shown in ordering information on page 16. 43.0 C0805A43011)2GA2) CTin-Coated, Final (SolderGuard II) 47.0 CO0805A47011)2GAQ2) HSolder-Coated, Final (SolderGuard |) 51.0 C0805A5 1 012 GAG) 56.0 CO805A560(N2 GAG) 62.0 CO805A620(N2 GAG) 75.0 CO805A750(N2GAG) 82.0 CO805A820(N2 GAG) 91.0 CO0805A9 1 O12 GAG) 100 C0805A101(N2GAG) 110 CO805A111M2GA2) 120 C0805A121(N2GAG) 130 C0805A131(N2GAG) 150 CO0805A151(N2GAG) 160 CO0805A161(N2GAG) 180 C0805A181(N2GAG) 200 C0805A201(N2GAG) 220 C0805A221(N2GAG) 100 VOLT - BP 240 C0805A24 10111 GA) 270 C0805A271(11 GAG) 300 C0805A301(11 GAG) 330 C0805A331(11 GAG) 360 C0805A361(11 GAG) 390 C0805A391(11 GAG) 430 C0805A431(11 GAG) 470 C0805A471(1 GAG) 50 VOLT - BP 510 C0805A5110)5GA2) 560 CO805A561(N5GAG) KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 17CERAMIC CHIPS HIGH RELIABILITY GR 900 SERIES (BP/DX DIELECTRIC) RATINGS AND PART NUMBER REFERENCE STYLE C1005 CAPACITANCE KEMET CAPACITANCE KEMET pF PART NUMBER pF PART NUMBER 200 VOLT - BP 200 VOLT - BP 1.0 C1005A1091N2GA2) 180 C1005A1811N2GA2) 14 C1005A1190)2GA2) 200 C1005A2011N2GA2) 12 C1005A1291N2GA2) 220 C1005A2211N2GA2) 15 C1005A1591N2GA2) 240 C1005A2411N2GA2) 1.6 C1005A1691N2GA2) 270 C1005A27112GA2) 18 C1005A1891N2GA2) 300 C1005A3011N2GA2) 2.0 C1005A2091N2GA2) 330 C1005A3311W2GA2) 22 C1005A2291N2GA2) 360 C1005A36112GA2) 24 C1005A2491N2GA2) 390 C1005A3911N2GA2) 27 C1005A2791N2GA2) 430 C1005A431W2GA2) 3.0 C1005A3091N2GA2) 470 C1005A471W2GAA) 3.3 C1005A3391N2GA2) 100 VOLT - BP 3.6 C100SAS691N2GAl2} 510 C1005A51101 GA) 3.9 C1005A3991N2G Al2} 560 C1005A561101 GAZ) 43 C1005A4391N2G AZ} 620 C1005A621101 GAZ. 47 C1005A4791N2G Az) 680 C1005A681111 GAZ 5.1 C1005A51 9i2GAl2} 750 C1005A751101 GAZ. ee O COE ApBetiDG me 820 C1005A82101)1 GAZ. 75 C1005A759U12GA2) 50 VOLT - BP gD CTOOSARPAIIDGAL) 910 C1005A911(5GAA o4 C1005A91 91112 GA) 1000 C1005A102W05GA2) 100 C1005A1 001112 GA) 1100 C1005A112U)5GAA 11.0 C1005A11 OWI2GAQ) 1200 C1005A122\N5GAA) 12.0 C1005A12012GA2) 200 VOLT - BX 13.0 C1005A130012GA2) 330 C1005A33 112XA2) 15.0 C1005A15001)2GA2) 390 C1005A39 112XA2) 16.0 C1005A1601112GA2) 470 C1005A47 1)2XA2) 18.0 C1005A180112GA2) 560 C1005A561)2XA2) 20.0 C1005A200112GA2) 680 C1005A68 11)2XA2) 22.0 C1005A2201112GA2) 820 C1005A82 1)2XA2) 24.0 C1005A2400)2GA2) 1000 C1005A102W)2XA2) 27.0 C1005A27 0U)2GA2) 1200 C1005A1 2202 XA2) 30.0 C1005A300U)2GA2) 1500 C1005A152W)2XA2) 33.0 C1005A3301)2GA2) 1800 C1005A182W)2XA2) 36.0 C1005A360112GA2) 100 VOLT - BX 39.0 C1005A39 0012G Al2) 2200 C1005A22211)1 XAZ) 43.0 C1005A43 0012G Al2) 2700 C1005A2721)1 XAZ) 47.0 C1005A4700)2G Al2) 3300 C1005A3321)1 XAZ) 51.0 C1005A51 OM2G Al2) 3900 C1005A39211)1 XA2) 56.0 C1005A5601112G Al2) 4700 C1005A4720)1 XA2) 62.0 C1005A6201)2G Al2) 5600 C1005A56211)1 XAZ) 75.0 C1005A7500)2G Al2) 6800 C1005A68211)1 XAZ) 82.0 C1005A8201)2G Al2) 8200 C1005A82211)1 XAZ) 91.0 C1005A91 OM2G Al2) 10,000 C1005A103()1 XA2) 100 C1005A10112GA2) 50 VOLT - BX 110 C1005A1112GA2) 12,000 C1005A123(N5XA2) 120 C1005A12102GAQ) 15,000 C1005A153(5XAI2) 130 C1005A13102GAG) 18,000 C1005A183(5XAI2) 150 C1005A15102GA2) 22.000 C1005A223(N5XAI2) 160 C1005A1 6112GA2) , RATINGS AND PART NUMBER REFERENCE STYLE C1206 CAPACITANCE KEMET CAPACITANCE KEMET pF PART NUMBER pF PART NUMBER 200 VOLT - BP 200 VOLT - BP 10.0 C1206A1 00012GA2) 27.0 C1206A2701N2G AZ) 11.0 C1206A11 02GA2) 30.0 C1206A300112GA2) 12.0 C1206A1201112GA2) 33.0 C1206A33012GA2) 13.0 C1206A1300112GA2) 36.0 C1206A36012GA2) 15.0 C1206A150112GA2) 39.0 C1206A390112GA2) 16.0 C1206A1 60U112GA2) 43.0 C1206A430112G A) 18.0 C1206A1800112GA2) 47.0 C1206A47012GA2) 20.0 C1206A2000112G AZ) 51.0 C1206A510112GA2) 22.0 C1206A2201112G AZ) 56.0 C1206A560112GA2) 24.0 C1206A240112G AZ) 62.0 C1206A620112G AZ) (1) Complete KEMET part number by inserting capacitance tolerance, as applicable as shown in ordering information on page 16. BP CAPACITANCE TOLERANCE: +1%, +2%, +5%, +10%, +20% (+0.5pF & +0.25pF tolerances available 1.0 thru 10pF only) TEMPERATURE CHARACTERISTIC G" BX CAPACITANCE TOLERANCE: +5%, +10%, +20% TEMPERATURE CHARACTERISTIC X" (2) Complete part number by inserting end Metallization, as applicable as shown in ordering information on page 16. CTin-Coated, Final (SolderGuard I!) HSolder-Coated, Final (SolderGuard |) 18 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300CERAMIC CHIPS HIGH RELIABILITY GR 900 SERIES (BP/DX DIELECTRIC) RATINGS AND PART NUMBER REFERENCE STYLE C1206 (continued) CAPACITANCE KEMET CAPACITANCE KEMET pF PART NUMBER pF PART NUMBER 200 VOLT - BP 50 VOLT - BP 68.0 C1206A6801N2 GA 1800 C1206A 182U5GA2. 75.0 C1206A75011/2GA2) 2000 C1206A20205G A. 82.0 C1206A82011/2GA2) 200 VOLT - BX 91.0 C1206A91 OW2GA2) 470 C1206A471()2XA2) 100 C1206A10102GAI2) 560 C1206A561112XAL2) 110 C1206A111(02GAQ2) 680 C1206A681(12XA(2) 120 C1206A12112GAL2) 820 C1206A8211N2XAL2) 130 C1206A13112GAI2) 1000 C1206A1 02112XAL2) 150 C1206A151(12GAI2) 1200 C1206A1 22112 XA(2) 160 C1206A16102GAI2) 1500 C1206A152102XA2) 180 C1206A181(12GAI2) 1800 C1206A182112XAL2) 200 C1206A20112GAI2) 2200 C1206A22211)2XA(2) 220 C1206A221(12GAL2) 2700 C1206A2721N2XA2) 240 C1206A241(12GAI2) 3300 C1206A3321N2XAL2) 270 C1206A271(12GAI2) 3900 C1206A392112XAL2) 300 C1206A301(12GA2) 4700 C1206A4721N2XA2) 330 C1206A33111/2GA2) 360 C1206A36111/2GA2) 100 VOLT - BX 5600 C1206A56211)1 XAL2) 390 C1206A39111)2GA2) 6800 C1206A68211)1 XAL2) 430 C1206A43111/2 GA) 8200 C1206A82211)1 XAL2) 470 C1206A47111/2GAQ) 100 VOLT - BP 10,000 C1206A10311)1 XAL2) 12,000 C1206A12311)1 XA2) 510 C1206A5110\1 GA) 15,000 C1206A153111 XA2) 560 C1206A56111)1 GA 7 620 C1206A62111)1 GA) 50 VOLT - BX 18,000 C1206A 183U115XA2) 680 C1206A68111)1 GA) 22,000 C1206A22311)5XAL2) 750 C1206A75111)1 GA) 27,000 C1206A273U)5XA2) 820 C1206A82111)1 GA) 33,000 C1206A333U1)5XAL2) 910 C1206A9114111 GAZ) 39,000 C1206A393U1)5XAL2) 1000 C1206A10211)1 GA) 47 000 C1 DOBAATSUIBXAD 1100 C1206A112111 GAZ , (US XA) 1200 C1206A12211)1 GA) 1300 C1206A13211)1 GA) 1500 C1206A15211)1 GA) 1600 C1206A16211)1 GA) RATINGS AND PART NUMBER REFERENCE STYLE C1210 CAPACITANCE KEMET CAPACITANCE KEMET pF PART NUMBER pF PART NUMBER 200 VOLT - BP 200 VOLT - BP 10.0 C1210A1 00W12GA2) 130 C1210A131M2GA2) 11.0 C1210A11 0W2GA2) 150 C1210A151M2GA2) 12.0 C1210A120102GA2) 160 C1210A161M2GA2) 13.0 C1210A130W02GA2) 180 C1210A181M2GA2) 15.0 C1210A150(02GA2) 200 C1210A201W2GA2) 16.0 C1210A1 60WJ2GA2) 220 C1210A221 N2GA2) 18.0 C1210A18012GA2) 240 C1210A241N2GA2) 20.0 C121 0A20012GA2) 270 C1210A271W2GA2) 22.0 C121 0A220102GA2) 300 C1210A301W2GA2) 24.0 C121 0A240i02GA2) 330 C1210A3312GA2) 27.0 C121 0A2702GA2) 360 C1210A361W2GA2) 30.0 C121 0A300W2GA2) 390 C1210A391M2GA2) 33.0 C121 0A33012GA2) 430 C1210A431M2GA2) 36.0 C121 0A360I2GA2) 470 C1210A471W2GA2) 39.0 C121 0A390I2GA2) 510 C1210A511N2GA2) 43.0 C121 0A430)2GA2) 560 C1210A561W2GA2) 47.0 C121 0A470W2GA2) 620 C1210A621(N2GA2) 51.0 C1210A510W2GA2) 680 C1210A681(N2GA2) 56.0 C121 0A560102GA2) 750 C1210A751M2GA2) 62.0 C121 0A62012GA2) 820 C1210A8212GA2) 68.0 C121 0A6801N2GA2) 910 C1210A911H2GA2) 75.0 C121 0A750W02GA2) 1000 C1210A102(02GAL2) eo O a One OMG A, coon ordering information on page 16. capacitance tolerance, as applicable as 100 C121 0A1 01(2GA2) BP CAPACITANCE TOLERANCE: #1%, 42%, +5%, #10%, 420% (40.5pF & #0.25pF 110 oratoartimecaa rer ner ean Gonna 120 C121 0A121(02GAG) CHARACTERISTIC x (2) Complete part number by inserting end Metallization, as applicable as shown in ordering information on page 16. CTin-Coated, Final (SolderGuard I!) HSolder-Coated, Final (SolderGuard |) KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 1920 CERAMIC CHIPS HIGH RELIABILITY RATINGS AND GR 900 SERIES (BP/DX DIELECTRIC) PART NUMBER REFERENCE STYLE C1210 (continued) CAPACITANCE KEMET CAPACITANCE KEMET pF PART NUMBER pF PART NUMBER 100 VOLT - BP 200 VOLT - BX 1100 C1210A1120)1GAQ2) 2200 C121 0A222N 2X Al2) 1200 C121 0A1 22011 GA2) 2700 C121 0A272U2XAL2) 1300 C121 0A132t1GA2) 3300 C121 0A332UN2XAl2) 1500 C121 0A15201 GA2) 3900 C121 0A392UN2XAL2) 1600 C121 0A1 6201 GA2) 4700 C121 0A472U2XAl2) 1800 C121 0A18201GA2) 5600 C121 OAS62U2XAL2) 2000 C121 0A202t11 GAZ) 6800 C121 0AGB2U2XAL2) 2200 C121 0A222011 GA) 8200 C121 0AB22U12XAL2) 2400 C121 0A242t1 GAZ) 10,000 C121 0A1 032K A2) 2700 C121 0A27201 GAZ) 100 VOLT - BX 3000 1210A30211 GAZ) 12,000 C1210A1 23101 XA) 3300 6121 0A33201 GA) 15,000 C1210A153(11 XA2) 50 VOLT - BP 18,000 C1210A183(1)1 XA(2) 3600 C121 0A362N5GA2) 22,000 C121 0A2231111 XA2) 3900 C121 0A392N5GA2) 27,000 C121 0A2731111 XA2) 200 VOLT - BX 33,000 C1210A333U111 XA2) 470 C1210A4712XA2). 50 VOLT - BX 560 C1210A561 2X A02) 39,000 C121 0A393U5XAL2) 680 C1210A681 M2XAL2) 47,000 C121 0A473U0)5XAL2) 820 C1210A821 2X Al2) 56,000 C121 OAS63U1)5XAL2) 1000 C1210A1 022K Al2) 68,000 C121 0AG83U115XAL2) 1200 C1210A1 222K Al2) 82,000 C121 0AB23U1)5XAL2) 1500 C1210A152)2XAl2) 100,000 C121 0A1 04U)5XAL2) 1800 C1210A182i2XAl2) RATINGS AND PART NUMBER REFERENCE STYLE C1805 CAPACITANCE KEMET CAPACITANCE KEMET pF PART NUMBER pF PART NUMBER 200 VOLT - BP 200 VOLT - BX 220 C1805A22112GA2) 1200 CT805A 122102 XAQ) 240 C1805A24112GA2. 1500 C1805A152112XA2) 270 C1805A27112GA2. 1800 C1805A182112XA2) 300 C1805A30112GA2. 2200 C1805A22211)2XA12) 330 C1805A33112GA2. 2700 C1805A272112XA2) 360 C1805A36112GA2. 3300 C1805A332112XAL2) 390 C1805A39112GA2. 3900 C1805A392112XA2) 430 C1805A431(112GA2) 100 VOLT - BX 470 C1 805A47102GAi2) 4700 C1805A4721N1 XA) 100 VOLT - BP 5600 C1805A56211)1 XAL2) 510 C1805A51111 GAZ. 6800 C1805A68211)1 XA2) 560 C1805A56111)1 GA. 8200 C1805A82211)1 XA2) 620 C1805A62111)1 GA. 10,000 C1805A10311)1XA2) 680 C1805A681 111 GA. 12,000 C1805A12311)1 XA) 750 C1805A751111 GA. 15,000 C1805A153111 XA) 820 C1805A821(1)1 GAZ) 50 VOLT - BX 910 C1805A911111 GAZ, 18,000 C1805A183105XAi2) 1000 C1805A 10211 GA2, 22,000 C1805A22311)5XA2) 1100 C1805A 1121111 GAZ, 27,000 C1805A27311)5XA2) 1200 C1805A 122111 GAI2), 33,000 C1805A33311)5XAL2) 1300 C1805A 13211 GA2), 39,000 C1805A39311)5XAL2) 1500 C1805A 15211 GA2), 47,000 C1805A47311)5XAi2) 50 VOLT - BP 1600 C1805A 16215GA2. 1800 C1805A18211)5GA2. 2000 C1805A20211)5GA2. 2200 C1805A22211)5GA2. (1) Complete KEMET part number by inserting capacitance tolerance, as applicable as shown in ordering information on page 16. BP CAPACITANCE TOLERANCE: 141%, +2%, +5%, +10%, +20% (+0.5pF & +0.25pF tolerances available 1.0 thru 10pF only) TEMPERATURE CHARACTERISTIC G BX CAPACITANCE TOLERANCE: +5%, +10%, +20% TEMPERATURE CHARACTERISTIC Xx (2) Complete part number by inserting end Metallization, as applicable as shown in ordering information on page 16. CTin-Coated, Final (SolderGuard II) HSolder-Coated, Final (SolderGuard I) KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300CERAMIC CHIPS HIGH RELIABILITY GR 900 SERIES (BP/DX DIELECTRIC) RATINGS AND PART NUMBER REFERENCE STYLE C1808 CAPACITANCE KEMET CAPACITANCE KEMET pF PART NUMBER pF PART NUMBER 200 VOLT - BP 50 VOLT - BP 330 CT808A33 12 GAD 5100 C1808A512115GA2. 360 C1808A36111/2GA2) 5600 C1808A56215GA2. 390 C1808A39111/2GA2) 200 VOLT - BX 430 C1808A431(12GAI2) 2200 C1808A222112XAL2) 470 C1808A471(12GAI2) 2700 C1808A272112XA2) 510 C1808A511012GA2) 3300 C1808A332112XAL2) 560 C1808A561 (12 GAL) 3900 C1808A392112XAL2) 620 C1808A621 (12 GAL) 4700 C1808A472112XA2) 680 C1808A681 (12 GAL) 5600 C1808A562112XAL2) 750 C1808A751(12GAL2) 6800 C1808A682(1)2XA(2) 820 C1808A821(12GAL2) 8200 C1808A822112XAL2) 910 C1808A911012GA2) 10,000 C1808A103112XAi2) 1000 C1808A10211/2GA2) 7 1100 C1808A112012GA2) 100 VOLT - BX 12,000 C1808A12311)1 XA2) 1200 C1808A12211/2 GA) 15,000 C1808A15311)1 XA2) 1300 C1808A13211/2GA2) 18,000 C1808A18311)1 XA2) 1500 C1808A152U1/2 GA) 100 VOLT - BP 22,000 C1808A22311)1 XAL2) 27,000 C1808A27311)1 XA2) 1600 C1808A 162111 GA) 33,000 C1808A333i11 XAi2) 1800 C1808A18211)1 GA) 7 2000 C1808A20211)1 GA) 50 VOLT - BX 39,000 C1808A393U)5XAL2) 2200 C1808A22211)1 GA) 47,000 C1808A473U)5XA2) 2400 C1808A242111 GA) 56,000 C1808A563U1)5XAL2) 2700 C1808A272111 GA) 68,000 C1808A6831)5XAL2) 3000 C1808A30211)1 GA) 82,000 C1808A82311)5XAL2) 3300 C1808A332011 GALL 100,000 C1808A1 04t15XA2 3600 C1808A3620111 GALI {SXAZ) 3900 C1808A39211)1 GA) 4300 C1808A432111 GA) 4700 C1808A472111 GA) RATINGS AND PART NUMBER REFERENCE STYLE C1812 CAPACITANCE KEMET CAPACITANCE KEMET pF PART NUMBER pF PART NUMBER 200 VOLT - BP 100 VOLT - BP 330 C1812A331W2GA2) 5600 C1812A56211)1 GA2) 360 C1812A3612GA2) 6200 C1812A62211)1 GA2) 390 C1812A391(2GA2) 6800 C1812A68211 GAZ) 430 C1812A431W)2GAQ) 50 VOLT - BP 470 C1812A471 2 GAR 7500 C181 2A7520)5GA2) 510 C1812A5112GAR) 8200 C181 2A8220115GA2) 560 C1812A561 2 GAR 9100 C1812A9120)5GA2) 620 C1812A621 U2 GAR 10,000 C1812A10305GA2) 680 C1812A681W2GA2) 200 VOLT - BX 750 C1812A751(2GA2) 820 C1812A821112GAQ 6800 C1812A68211)2 XA2) 910 C1812A9111)2GA2) 8200 C1812A8221)2 XA2) 4000 C1812A1 02U12GAQ 10,000 C1812A1 03102 XA2) 4100 C1812A1120)2GA2) 12,000 C1812A123(02 XA) 4200 C1812A1 2212 GA) 15,000 C1812A153(02 XA) 4300 C1812A1 3212 GA 18,000 C1812A183i2 XA) 1500 C1812A1 52102 GA) 100 VOLT - BX 1600 C1812A1 6212 GA) 22,000 C1812A22311)1 XA2) 1800 C1812A182(N2 GAZ 27,000 C1812A27311)1 XA) 2000 C1812A202N2GAQ). 33,000 C1812A333(11 XAQ2) 2200 C1812A2222 GA) 39,000 C1812A393(1)1 XA2) 2400 C1812A242N2GAZ 47,000 C1812A47311)1 XA) 2700 C1812A272N2GAQ). 56,000 C1812A563(111 XA2) 100 VOLT - BP 68,000 C1812A68311)1 XA) 3000 C1812A30211)1 GAi2) 50 VOLT - BX 3300 C1812A332(1)1 GA) 82,000 C1812A82311)5 XA) 3600 C1812A362(1)1 GAZ). 100,000 C1812A104(15XAQ2) 3900 C1812A39211)1 GA). 120,000 C1812A124(15XAQ2) 4300 C1812A432(11 GAZ) 150,000 C1812A1 54105 XA) 4700 C1812A47211)1 GA) 180,000 C1812A1 84105 XA2) 5100 C1812A51 21111 GA) (1) Complete KEMET part number by inserting capacitance tolerance, as applicable as shown in ordering information on page 16. BP CAPACITANCE TOLERANCE: +1%, 42%, +5%, 410%, +20% (+0.5pF & +0.25pF tolerances available 1.0 thru 10pF only) TEMPERATURE CHARACTERISTIC G BX CAPACITANCE TOLERANCE: +5%, +10%, +20% TEMPERATURE CHARACTERISTIC X (2) Complete part number by inserting end Metallization, as applicable as shown in ordering information on page 16. CTin-Coated, Final (SolderGuard II) HSolder-Coated, Final (SolderGuard |} KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300 21CERAMIC CHIPS HIGH RELIABILITY GR 900 SERIES (BP/DX DIELECTRIC) RATINGS AND PART NUMBER REFERENCE STYLE C1825 CAPACITANCE KEMET CAPACITANCE KEMET pF PART NUMBER pF PART NUMBER 200 VOLT - BP 200 VOLT - BX 2700 C1825A27202GA2) 10,000 C1825A1032XAl2, 3000 C1825A302W2GAL2) 12,000 C1825A1232XAl2, 3300 C1825A332W2GA2) 15,000 C1825A1532XAl2, 3600 C1825A362W2GAL2) 18,000 C1825A1832XAl2, 3900 C1825A392W2GAL2) 22,000 C1825A223N2XAl2, 4300 C1825A432W2GA2) 33,000 C1825A3332XAl2, 4700 C1825A47202GAL2) 39,000 C1825A3932XAl2, 5100 C1825A51202GAL2) 47,000 C1825A47302XAl2, 5600 C1825A56202GA2) 100 VOLT - BX 100 VOLT - BP 56,000 C1825A563(111 XA, 6200 C1825A6221)1 GAL) 68,000 C1825A68311)1 XAl2, 6800 C1825A68201)1 GAL) 82,000 C1825A82311)1 XAl2, 7500 C1825A7520)1 GAL) 100,000 C1825A10411 XA, 8200 C1825A822011 GAL) 120,000 18250124101 XAl2, 9100 1825091201 GAL) 150,000 618250154101 XA2) 10,000 1825010301 GA) 50 VOLT - BX 11,000 61825A11311 GAL) 180,000 C1825A184(15XA2, 12,000 61825A12311 GAI2) 220,000 C1825A224(115XA2, 13,000 61825A133i1 GAI2) 270,000 C1825A274(5XA2, 15,000 C1825A153111 GAI2) 330,000 C1825A334(115XA2, 16,000 1825A1 63111 GAI2) 390,000 C1825A394(115XAI2, 18,000 G1825A183i01 GAZ) 470,000 C1825A474(15XA2, 50 VOLT - BP 20,000 C1825A20305GA2) 22,000 C1825A2230)5GA2) RATINGS AND PART NUMBER REFERENCE STYLE C2225 CAPACITANCE KEMET CAPACITANCE KEMET pF PART NUMBER pF PART NUMBER 200 VOLT - BP 200 VOLT - BX 2700 C2225A272012GAR) 78,000 C2225A1832XAQ, 3000 C2225A302U112GAQ) 22,000 C2225A2230)2XAl2) 3300 C2225A332U112GAQ) 27,000 C2225A2730)2XAl2, 3600 C2225A362112GA2) 33,000 C2225A3330)2XAl2, 3900 C2225A3921112GAQ) 39,000 C2225A3930)2XAl2, 4300 C2225A432U112GA2) 47,000 C2225A4730)2XA2) 4700 C2225A472U112GAQ) 100 VOLT - BX 5100 C2225A51 2U2GAl2) 56,000 C2225 A563(111 XAI2, 5600 C2225A5622GAl2) 68,000 C2225 A683(1)1 XAI2L 8200 C2225A6222GAl2) 82,000 C2225 A823(11 XAI2, 8800 C2225A08212GAl2) 100,000 C2225 A104(11 XA. 7500 C2225A7522GAl2) 120,000 C2225 A124(11 XA, 8200 C2225A82eeGAl2) 150,000 C2225A154(11 XA, 100 VOLT - BP 180,000 C2225A1840)1XA2) 9100 C2225A91 211 GAR) 50 VOLT - BX 10,000 C2225A1 0311 GAI2) 220,000 C2225 A22AINSXAI2, 11,000 02225A113111 GAZ) 270,000 C2225 A27 4(NSXAI2, 12,000 C2225A1 2301 GAl2) 330,000 C2225 A334(NSXAI2, 13,000 C2225A13301GAl2) 390,000 C2225 A394(NSXAI2, 1,000 C2225A153(1 GAI2) 470,000 C2225 A47 4(NSXAI2L 16,000 C2225A1 6311 GAI2) 560,000 C2225 A564(NSXAI2L 18,000 C2225A18311 GAI2) 680,000 C2225 ABB4(NSXAI2L 20,000 C2225A20311 GAI2) 820,000 C2225 A824(NSXAI2, 22,000 C2225 A223 GAZ) 1,000,000 C2225 A1 05(NSXAI2L 50 VOLT - BP 24,000 C2225A2430)5GA2) 27,000 C2225A2730)5GA2) (1) Complete KEMET part number by inserting capacitance tolerance, as applicable as shown in ordering information on page 16. BP CAPACITANCE TOLERANCE: 41%, +2%, +5%, 10%, +20% (+0.5pF & +0.25pF tolerances available 1.0 thru 10pF only) TEMPERATURE CHARACTERISTIC G BX CAPACITANCE TOLERANCE: +5%, +10%, +20% TEMPER- ATURE CHARACTERISTIC X (2) Complete part number by inserting end Metallization, as applicable as shown in ordering information on page 16. CTin-Coated, Final (SolderGuard II) HSolder-Coated, Final (SolderGuard I) 2? KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300KEMET KEMET ELECTRONICS CORPORATION Three Civic Plaza, Suite 240 Newport Beach, California 92660 Phone: Western Region U.S. A. FAX: KEMET ELECTRONICS CORPORATION Schaumburg Corporate Center, Suite 110 1515 Woodfield Road Schaumburg, Illinois 60173 Phone: Central Region U.S.A. FAX: KEMET ELECTRONICS CORPORATION Piedmont Center East, Suite 410, B-137 37 Villa Road Greenville, South Carolina 29615 Phone: Southeastern Region U.S. A. FAX: KEMET ELECTRONICS CORPORATION Park West East Tract 1603 LBJ Freeway, Suite 830 Dallas, Texas 75234 Phone: West Central Region U.S. A. FAX: KEMET ELECTRONICS CORPORATION 301 Edgewater Place, Suite 208 Wakefield, MA 01880 Phone: New England Region U.S. A. FAX: KEMET ELECTRONICS CORPORATION 2350 Mission College Blvd., Suite 390 Santa Clara, California 95054 Phone: Northwestern Region U.S. A. FAX: KEMET ELECTRONICS (Canada) LTD. 105-7145 W. Credit Ave., Bldg. 2 Phone: Mississauga, Ontario L5N 6J7 FAX: KEMET ELECTRONICS (Canada) LTD. 66 Rue Dubois, Suite 212 Phone: St-Eustache, Quebec J7P 4W9 FAX: KEMET ELECTRONICS S.A. 15 Chemin des Mines Phone: P.O.B. 76, CH 1211 Geneva, 20 Telex: Switzerland FAX: KEMET ELECTRONICS GMBH Hans-Stiessberger-Strasse 2A Postfach 1380 D 85540 Haar/Munich Phone: Germany FAX: KEMET ELECTRONICS S.A.R.L. 2, Rue Nicolas Ledoux Silic 254 94568 Rungis-Cedex Phone: France FAX: KEMET ELECTRONICS LTD. Waterfront House, 55/61 South St. Bishop's Stortford Hertfordshire CM23 3AL Phone: United Kingdom FAX: KEMET ELECTRONICS LTD. Brickhill East, Cratloe Co. Phone: Clare, lreland FAX: KEMET ELECTRONICS Via Gaetano Ermoli, 22 ScF, INT. 11 Phone: 00155, Rome, Italy FAX: KEMET ELECTRONICS ASIA LTD. 4A Chuan Hing Industrial Bldg. 14 Wang Tai Road Phone: Kowloon Bay, Hong Kong FAX: Capacitors KEMET Electronics Corporation WORLD SALES HEADQUARTERS Post Office Box 5928 Greenville, South Carolina 29606 - USA Tel: (864) 963-6300 FAX: (864) 963-6521 (714) 640-9320 (714) 720-9807 (847) 517-1030 (847) 517-1087 (864) 242-5789 (864) 242-5795 (972) 241-7501 (972) 241-5604 (617) 245-4646 (617) 245-1595 (408) 986-0424 (408) 986-1442 (905) 542-7930 (905) 542-7949 (514) 472-6677 (514) 472-7899 41-22-738-4244 845-412901 KESA CH 41-22-738-3918 49-89-45-64-200 49-89-46-04-117 33-1-45-12-53-20 33-1-46-87-40-87 44-1279-757-343 44-1279-757-188 353-61-357-229 353-61-357-455 39-6-232-3-1718 39-6-232-3-3081 852-2305-1168 852-2759-0345 KEMET ELECTRONICS S.A. Sector Oficios 26-2-B Phone: 34-1-804-43-03 Tres Cantos - 28760 Madrid, Spain FAX: 34-1-804-44-77 KEMET ELECTRONICS ASIA LTD. Suite 1512,15/F, Lucky Tower B 3 Dong San Huan Bei Road Chao Yang District Phone: 86-10-6462-0173 Beijing 100027, China FAX: 86-10-6461-5707 KEMET ELECTRONICS MARKETING (S) PTE LTD 8-2-04 Sunny Point Kompleks Jalan Batu Uban 11700 Gelugor Phone: 60-4-65-952-00 Palau Penang, Malaysia FAX: 60-4-65-952-20 KEMET ELECTRONICS MARKETING (S) PTE LTD 24 ANG MO KIO St. 65 Ground Floor (West Wing) Phone: 65-484-2220 Singapore 569061 FAX: 65-484-1110 KEMET ELECTRONICS CORPORATION., Taiwan Branch 3-4 F., No. 148, Section 4 Chung-Hsaio E. Rd. Phone: 886-2-752-8585 Taipei, Taiwan ROC FAX: 886-2-721-3129 UNICOM INTERNATIONAL CORPORATION Room 702, Shinhwa Bldg. 34-1 Mapo-Dong Mapo-Gu Phone: 82-2-712-5821 Seoul, Korea 121-050 FAX: 82-2-712-5823 CRUSADER ELECTRONIC COMPONENTS PTY. LTD.- 3/92 Bryant Street P.O. Box 226 Phone: 61-2-792-3922 Padstow NSW 2211 Telex: 790-123993 CRUSAD Australia FAX: 61-2-792-1446 MULTITECH ELECTRONICS CORPORATION (PTY) LTD P.O. Box 23351 Claremont 7735 Phone: 27-21-64-4103 Republic of South Africa FAX: 27-21-64-1360 ELECTRONIC BUILDING ELEMENTS (PTY) LTD 178 Erasmus Street Meyerspark, Pretoria, 0184 Phone: 27-12-803-7680 Republic of South Africa FAX: 27-11-803-8294 ELECTRONIC ENTERPRISES (HEAD OFFICE) Post Bag No. 6367 216, Regal Industrial Estate Archarya Donde Marg. Sewri, Bombay 400 015 Phone: 91-22-413-7096 India FAX: 91-22-413-3341 LANDSEAS ISRAEL LTD. 3 Yehonathan Nethanyahu St. P.O.B. 676 OR Yehuda 60 256 Phone: 972-3-5333033 Israel FAX: 972-3-5333052 HITECH ELECTRONICA INDUSTRIAL COMMERCIAL LTDA. Rua Branco De Moraes 489 CH Santo Antonio 04718-0010SP - Sao Paulo, Phone: 55-11-882-4000 Brazil FAX: 55-11-882-4100 ELKO S. R. L. AV Belgrano 1661 Phone: 54-1-46-1101 1093 Buenos Aires Telex: 390-17561 Argentina FAX: 54-1-325-8819 CIBER ELECTRONICA S.A. de C.V. Prolongacion Arbol No. 33 (2080) Col. Chapalita Sur Guadalajara, Jal 45000 Phone: 52-36-47-52-17 Mexico FAX: 52-31-21-33-31 NOTICE: Place "011" in front of the above Phone and FAX Numbers of Europe and Asia, when dialing from a United States exchange. NOTE... KEMET reserves the right to modify minor details of internal and external construction at an that might result from the use of KEMET Capacitors in potential circuit designs. " time in the interest of product improvement. KEMET does not assume any responsibility for infringement MET" is a registered trademark of KEMET Electronics Corporation KEMET Electronics Corporation 1997 10/15/97