DOCUMENT NUMBER SSC-PNE Series Single-Mode Pre-Angle SC CONNECTOR PLUG - for Angled-PC / Easy-assemble type - TECHNICAL SPECIFICATIONS Seiko Instruments Inc. Components Headquarters. 8, Nakase 1-Chome Mihama-ku, Chiba-shi, Chiba-ken 261-8507 JAPAN Telephone : +81-43-211-1211 Facsimile : +81-43-211-8030 NCD-69B8-03 SSC-PE Series Single-Mode Pre-Angle SC CONNECTOR PLUG - for Angled-PC / Easy-assemble type TECHNICAL SPECIFICATIONS Document Number NCD-69B8-02 NCD-69B8-01 NCD-69B8-02 NCD-69B8-03 September 1996 July 1999 April 2000 Copyright 1996, 1999, 2000 by Seiko Instruments Inc. All right reserved. The information contained herein shall not reproduced or disclosed to any third party without the express written consent of SII. The Specifications contained herein are subject to change without notice. SII is a trademark of Seiko Instruments Inc. Please address any questions, comments, and suggestions to: Seiko Instruments USA Inc. Seiko Instruments GmbH Seiko Instruments (H.K.) Ltd. Seiko Instruments Taiwan Inc. Electronics Components Division 2990 West Lomita Boulevard Torrance, CA 90505, U.S.A. Phone: +1-310-517-7780 Facsimile: +1-310-517-7792 Sales Department 4th & 5th Floor, Wyler Center 2 200 Tai Lin Pai Road, Kwai Chung N.T., Kowloon, Hong Kong Phone: +852-2421-8611 Facsimile: +852-2480-5479 OFC Division Siemensstrae 9b D-63263 Neu-Isenburg, Germany Phone: +49-6102-297-0 Facsimile: +49-6102-297-211 Sales Department 4F, No.40, Sec. 2, Min Chuan E. Rd., Taipei 104, Taiwan, R.O.C. Phone: +886-2-2563-5001 Facsimile: +886-2-2521-9519 Seiko Instruments Singapore pte. Ltd. Component Sales Department 2, Marsiling Lane, Singapore, 739144, Singapore Phone: +65-269-1370 Facsimile: +65-269-9729 ii TABLE OF CONTENTS Section 1. PROVISION 1.1. Application limit 2. PARTS NUMBER 3. GENERAL SPECIFICATIONS 3.1. Parts and Materials 3.2. Physical Dimensions 3.3. General Tolerance 4. PACKING Page 1 1 1 2 2 2 2 2 Table Table 1 Table 2 Table 3 Table 4 Parts number Parts and materials Parts and materials (Mainbody) General tolerance 1 2 2 2 Figure Figure 1 SSC-PNE Connector (Cord type) Figure 2 SSC-PNE Connector ( Bufferd fiber type) Figure 3 Mainbody Figure 4 to 12 Part dimensions iii 3 4 5 6 iv 1. PROVISION 1.1 Application Limit These specifications apply to the SSC-PNE single-mode pre-angle SC CONNECTOR PLUG supplied by SII. 2. PARTS NUMBER Parts number of the connector is shown in Table 1. Table 1 MODEL Number Parts number TYPE Number SSC-PNE 8 7 1 2 5 1 B 3 0 0 0 8 0 1 6 7 9 Hood color without hood Green ( Requied ) 00 Package 1 Individual 3 Bulk Hood Inner Dia without hood 0.9mm (non flamable) 2.0mm (Plastic) 3.0mm (Plastic) 0.9mm (Plastic) 0 8 B Ferrule Inner Dia S5 to S6 Cap without Green PVC Green Ferrule Cap Marking of Grip 1 SII / SSC-P ( 0.125 to 0.126mm ) 1 3. GENERAL SPECIFICATIONS 3.1 Parts and Materials Parts and the materials are shown in Table 2 to 3. No. 1 2 3 4 5 6 7 8 14 15 Table 2 Parts and materials Part Name Mainbody Grip Crimping ring Q'ty Material Hood ( 1 ) Thermal plastic elastomer 1 See Table 3 1 PBT GF ( 1 ) Aluminum alloy Aluminum alloy Thermal plastic elastomer Synthetic rubber Thermal plastic elastomer ( 1 ) PP PVC Cap No. Part Name 9 Ferrule 10 Flange 11 Plug frame 12 Spring 13 Stop ring Table 3 Q'ty 1 1 1 1 1 Notes Sub-assembled Green, UL94V-0 for 3.0mm cable for 2.0mm cable for 3.0mm, UL94V-0, Green for 2.0mm, UL94V-0, Green for 0.9mm, UL94V-0, Green for 0.9mm, UL94V-0, Green Green Green Parts and materials ( Mainbody ) Material Zirconia Brass PBT GF Stainless steel Brass Nickel plating White, UL94V-0 Nickel plating Notes -- -- 3.2 Physical Dimensions Figure 1 shows the assembled state of SSC-PNE ( Cord type ). Figure 2 shows the assembled state of SSC-PNE ( Buffered fiber type ). Figure 3 shows the Mainbody. Figure 4 to 11 show the part dimension. - In accordance with IEC 61754-4 Fibre optic connector interface Part 4 : Type SC connector family. - In accordance with JIS C 5973 F04 type connectors 3.3 General Tolerances Permissible deviation in dimensions without tolerance indication is in accordance with JIS B 0405 class m, as shown in Table 4. Table 4 General tolerance (JIS B 0405 class m) Basic size step [mm] Over Under 0.5 3 3 6 6 30 30 120 Permissible deviation [mm] 0.1 0.1 0.2 0.3 4. PACKING The product is packed to prevent damage during shipment. 2 note.1: This drawing shows the tentatively assembled condition. In practice, the connector plug is not assembled like this. note.2: This drawing does not include caps. Figure 1 SSC-PNE Connector ( Cord type ) 3 Unit: mm note.1: This drawing shows the tentatively assembled condition. In practice, the connector plug is not assembled like this. note.2: This drawing does not include caps. Figure 2 SSC-PNE Connector ( Buffered fiber type ) 4 Unit: mm note.1: Ferrule hole diameter ( capillary ) shows Table 1. Figure 3 #1 : Mainbody Figure 4 #2 : Grip 5 Unit: mm Unit: mm Figure 5 #3 : Crimping ring ( for 3.0mm cord ) Figure 6 #4 : Crimping ring ( for 2.0mm cord ) Figure 7 Figure 8 #5 : Hood ( for 3.0mm cord ) #6 : Hood ( for 2.0mm cord ) 6 Unit: mm Unit: mm Unit: mm Unit: mm Figure 9 Figure 10 #7 : Hood ( for 0.9mm buffered fiber ) #8 : Hood ( for 0.9mm buffered fiber ) Figure 11 Figure 12 #14 Cap ( Ferrule Cap ) #15 : Cap ( PVC ) 7 Unit: mm Unit: mm Unit: mm Unit: mm