Series AM2L-NZ
2 Watt | DC-DC Converter
www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832)
F 051e R12.S 1 of 4 North America only
FEATURES:
• Low Profile SMD
• MTBF>1,000,000 hours
• 1000VDC & 6000VDC Isolation
• Operating temperature: -40°C to +85°C
• Industry Standard Pinout
• High Efficiency up to 85%
• Unregulated Single & Dual Outputs
Models
Single output
Model
Input Voltage(V)
Output Voltage
(V)
Output Current
max(mA)
Isolation
(VDC)
AM2L-0505SH60-NZ
4.5-5.5
5
400
6000
AM2L-1205SH60-NZ
10.8-13.2
5
400
6000
AM2L-1215SH60-NZ
10.8-13.2
15
133
6000
AM2L-2405SH60-NZ
21.6-26.4
5
400
6000
AM2L-2415SH60-NZ
21.6-26.4
15
133
6000
Models
Dual output
Model
Input Voltage
(V)
Output Voltage
(V)
Output Current
max (mA)
Isolation
(VDC)
AM2L-0505D-NZ
4.5-5.5
±5
±200
1000
AM2L-0512D-NZ
4.5-5.5
±12
±83
1000
AM2L-1215D-NZ
10.8-13.2
±15
±67
1000
NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at
rated output load unless otherwise specified.
Input Specifications
Parameters
Nominal
Typical
Maximum
Units
Voltage range
5
4.5-5.5
VDC
12
10.8-13.2
24
21.6-26.4
Isolation Specifications
Parameters
Conditions
Typical
Rated
Units
Tested I/O voltage
60 sec
1000, 6000
VDC
Capacitance
500VDC
10
pF
Resistance
500Vdc
>1000
MOhm
Output Specifications
Parameters
Conditions
Typical
Maximum
Units
Voltage accuracy
See Tolerance Graph
±5
%
Short Circuit protection
1000VDC Momentary
1 sec
6000VDC Continuous
Short Circuit Restart
Auto-Recovery
Line voltage regulation
For a 1% change of Vin
±1.2
%
Load voltage regulation (5 Vout)
From 10% load to 100% load
12.8
%
Load voltage regulation (12 Vout)
6.8
Load voltage regulation (15 Vout)
6.3
Temperature coefficient
At 100% load
±0.03
%/oC
Ripple & Noise*
20MHz Bandwidth
150
mV p-p
Minimum Load Current**
10
% of Max
*Test ripple & noise by “Parallel Cable Method” as described in Application Note “Ripple and Noise Measurement of Brick &
POL DC-DC Converters” available on Aimtec’s website www.aimtec.com
Click on Series name for product info on aimtec.com
Series AM2L-NZ
2 Watt | DC-DC Converter
www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832)
F 051e R12.S 2 of 4 North America only
**If the operating output current is less than 10% of maximum it is recommended to install a load resister in parallel with the
load to ensure the actual load current meets the minimum load current requirement.
General Specifications
Parameters
Conditions
Typical
Maximum
Units
Switching frequency
100% load, nominal input
100
KHz
Operating temperature
-40 to + 85
oC
Storage temperature
-55 to + 125
oC
Maximum case temperature
100
oC
Cooling
Free Air Convection
Humidity
95
% RH
Case material
Plastic(UL94-V0)
Weight
1000VDC
2.1
g
6000VDC
3.8
Dimensions (L x W x H)
Single & Dual 1000VDC
0.70 x 0.70 x 0.24 inches 17.78 x 17.78 x 6.00 mm
Single 6000VDC
0.94 x 0.79 x 0.32 inches 23.86 x 18.50 x 8.00mm
MTBF
>1,000, 000 hours (MIL-HDBK -217F, Ground Benign, t=+25ºC)
Maximum Soldering Temperature
1.5mm from case for 10 seconds
260
oC
Safety Specifications
Parameters
Agency approvals
CE (for 6000VDC isolation models)
Standards
EN 60601-1-1; EN 60601-1-2
Pin Out Specifications
1000VDC 6000VDC
NOTE: On dual output models Pin 5 and Pin 10 are connected internally together.
Either Pin 5 or Pin 10, or both can be used as the -Vout
NC: not connected
Pin
Single
1
- V in
2
No Pin
3
No Pin
4
No Pin
5
No Pin
6
No Pin
7
NC
8
NC
9
+V out
10
-V out
11
No Pin
12
No Pin
13
No Pin
14
No Pin
15
No Pin
16
+V in
Pin
Single
Dual
1
-Vin
- Vin
2
+ Vin
+ Vin
5
NC
-Vout
6
- Vout
Common
7
+Vout
+Vout
8
NC
NC
9
NC
NC
10
NC
-Vout
12
NC
NC
13
NC
NC
14
NC
NC
Series AM2L-NZ
2 Watt | DC-DC Converter
www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832)
F 051e R12.S 3 of 4 North America only
Dimensions 1000VDC
Dimensions 6000VDC
23.86
(0.94)
8.00
(0.32)
2.00
(0.08)
1.00
(0.04)
7.50
(0.30)
2.54
(0.10)
3.04
(0.12)
17 8
910
16
15.24
(0.60)
18.50
(0.73) 13.70
(0.54)
Side View
Top View
13.10
(0.52)
Front View
18.50
(0.73)
A
A
1.35 ± 0.13
(0.05 ± 0.005) MAX
0.50
(0.01)
5.00º
angle
Typical Load Line
Tolerance Envelope Graph
Output Current(%)
Output Voltage
+2.5%
-2.5%
-7.5%
+10%
+5%
10%50%100%
A
0.25
(0.01)
1.30 ±0.13
(0.05 ±0.005) MAX
0.25
(0.01)
5.00º angle
A
17.78
(0.70)
17.78
(0.70)
5.75
(0.23)
Top View
Front View
Side View
6.00
(0.24)
17
910
14
17.78
(0.70)
1.00
(0.04)2.54
(0.10)
2.75
(0.11)
652 3
13 12 8
12.70
(0.50)
1.27
(0.05)
2.54
(0.10)
2.00
(0.08)
Series AM2L-NZ
2 Watt | DC-DC Converter
www.aimtec.com Tel: +1 514 620 2722 Toll free: + 1 888 9 AIMTEC (924 6832)
F 051e R12.S 4 of 4 North America only
Recommended Filter Circuit
If it is required to decrease the input/output ripple an “LC” filter network can be installed on the input and output of the
converter (see above).
It should be noted that the inductance and the resonant frequency of the “LC” filtering network should differ from the DC/DC
converter switching frequency to avoid mutual interference.
The capacitance of the outputfilter capacitor must not exceed the values in the Table below to avoid startup problems and
ensure safe and reliable operation.
It’s not recommended to connect any external capacitor in the application field whenoutput loading is less than 0.5
watt.
External Capacitor Tables
Input Capacitor (Cin) Output Capacitor (Cout)
Overload Protection
The output circuit of these products has no protection against overload. It is recommended to install external overload
protection in the form of a self-recovery fuse or a circuit breaker in series at the converter’s input.
To achieve a high degree of output voltage regulation, over-voltage, and over-current protection it is suggested to use the
AM2LV-NZ series as an alternative.
NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled
by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the
date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%,
nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components
and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This
product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate
specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com.
Vin
(VDC)
Cin
(uF)
5
4.7
12
2.2
24
1
Single
Vout
(VDC)
Cout
(uF)
Dual
Vout
(Vdc)
Cout
(uF)
5
10
±5
4.7
15
1
±12
1
±15
0.47
DC DC
+ Vin
- Vin
+
Cin
+Cout
+Cout
+Vout
-Vout
Common
Dual Output
LL
L
DC DC +Cout
+Vout
- Vin
Single Output
+ Vin
- Vin
+
Cin
LL