LRC-LRF_E.qxd 12/23/04 10:07 AM Page 1 Low Value Flat Chip Resistor Welwyn Components LRC/LRF Series * * * Standard 2512, 2010 and 1206 sizes * * Low inductance - less than 0.2nH Resistance values down to 0.003 ohms Leach resistant solder-plated copper wrap-around termination AEC-Q200 Qualified Electrical Data LR1206 LR2010 LR2512 Power rating at 70C watts 0.5 1.0 1.5/2.0* Resistance range ohms 0R010 to 1R 0R003 to 1R 0R003 to 1R volts 200 200 200 Dielectric withstanding voltage TCR ppm/C Resistance tolerance 100 (Contact factory for value below 0.050 ohms) R005 5%, >R005 1, 2, 5% % Temperature rise at rated power Pad and trace area for max power rating @ 70C *2 Watts with total solder pad and trace size of 300 mm C 40 80 90 mm2 30 30 100 2 Physical Data Dimensions (mm) Size L W H (max) D D1 LR1206 3.200.305 1.630.203 0.8 0.480.25 0.480.25 LR2010 5.230.38 2.640.25 0.8 0.480.25 0.480.25 LR2512 6.500.38 3.250.25 0.8 0.480.25 0.480.25 LR 1206 / 2010 / 2512 W L H D Protective Overcoat Resistive Element Copper Termination Solder Plating Nickel Barrier Layer Copper Wraparound Termination Alumina Substrate General Note Welwyn Components reserves the right to make changes in product specification without notice or liability. All information is subject to Welwyn's own data and is considered accurate at time of going to print. (c) Welwyn Components Limited * Bedlington, Northumberland NE22 7AA, UK Telephone: +44 (0) 1670 822181 * Facsimile: +44 (0) 1670 829465 * Email: info@welwyn-tt.com * Website: www.welwyn-tt.com A subsidiary of TT electronics plc 04.10 23 LRC-LRF_E.qxd 12/23/04 10:07 AM Page 2 Low Value Flat Chip Resistor Welwyn Components LRC/LRF Series Dimensions (mm) A A B C LR1206 2.0 4.0 1.25 LR2010 3.05 6.5 1.5 LR2512 3.7 7.75 1.5 B C Max. (add R05) R% 0.5 Typ. (%) 100 0.2 80 (@1R0) R% 0.25 0.1 4 Temperature Cycling 6 Moisture Resistance MIL-STD-202 Method 106 JESD22 Method JA-104 R% 0.5 0.2 7 Biased Humidity MIL-STD-202 Method 103 R% 0.5 0.2 8 Operational Life (Cyclic Load) MIL-STD-202 Method 108 R% 14 Vibration MIL-STD-202 Method 204 R% 0.5 0.05 15 Resistance to Soldering Heat MIL-STD-202 Method 210 R% 0.25 0.05 16 1 0.5 60 40 20 0 25 R% 0.25 0.1 Thermal Shock MIL-STD-202 Method 107 18 Solderability 21 Board Flex AEC-Q200-005 R% 0.5 22 Terminal Strength AEC-Q200-006 R% 0.25 0.1 J-STD-002 70 150 (C) Ambient temperature >95% coverage 0.2 6.25 x Pr for 2s R% 0.5 Low Temperature Storage -65C for 100 hours R% 0.5 Leach Resistance Solder dip at 250C 90s minimum Short Term Overload Power Rating ref 3 AEC-Q200 Table 7 Method Test High Temp. Exposure MIL-STD-202 Method 108 LRC 25 12 2 1 watt LRC 20 10 1 0.w 5 at wat t t LRC 12 06 0.5 25ww atat tt Note: 1. Although 2010 and 2512 sizes have passed temperature cycling and thermal shock, it is in general not recommended that ceramic chips this large be used on FR4 in a severe temperature cycle environment due to the possibility of solder joint fatigue. 2. Full AEC-Q200 qualification applies to ohmic values R01. Ordering Procedure Example: LRF2512 at 10 milliohms (hence flip-chip mounted) and 2% tolerance on a reel of 1800 pieces LRF2512-R01GW Type Mounting F Conventional (element up) Flip-chip (element down) Values > R025 Values < R025 Size Value (use IEC62 code) Tolerance (use IEC62 code) F G J 1% 2% 5% Packing W T1 Tape 1206 or 2010 2512 All sizes 3000/reel 1800/reel 1000/reel Standard (c) Welwyn Components Limited Bedlington, Northumberland NE22 7AA, UK Telephone: +44 (0) 1670 822181 * Facsimile: +44 (0) 1670 829465 * Email: info@welwyn-tt.com * Website: www.welwyn-tt.com 04.10