DATA SHEET AAT3690 1.0A USB Port/Adapter Li-Ion/Polymer Battery Charger General Description Features The AAT3690 BatteryManager is a highly integrated single-cell lithium-ion/polymer battery charger IC designed to operate with USB port and AC adapter inputs. It requires the minimum number of external components. * USB/AC Adapter System Power Charger USB: Programmable up to 1.0A Adapter: Programmable up to 1.0A * 4.0V to 5.5V Input Voltage Range * Adapter Presence Automatically Disables USB Charging * High Level of Integration With Internal: Charging Devices Reverse Blocking Diodes Current Sensing * Automatic Recharge Sequencing * Digital Thermal Regulation in ADP Charge * Charge Reduction Loop in USB Charge * Battery Temperature Monitoring * Full Battery Charge Auto Turn-Off * Over-Current Protection * Over-Voltage Protection * Emergency Thermal Protection * Power On Reset and Soft Start * Serial Interface Status Reporting * 12-Pin 3 x 3mm TDFN Package The AAT3690 precisely regulates battery charge voltage and current for 4.2V lithium-ion/polymer battery cells. Adapter charge current rates can be programmed up to 1.0A. In the absence of an adapter and with a USB port connected, the battery can also be charged by USB power. The USB charge current can be programmed up to 1A. A Charge Reduction Loop is also built in to allow users to charge the battery with the available current from a USB port, while keeping the port voltage regulated. USB charging is disabled when an adapter is present. Battery temperature and charge state are fully monitored for fault conditions. In the event of an over-voltage or over-temperature condition, the device will automatically shut down, thus protecting the charging device, control system, and the battery under charge. Status monitor output pins are provided to indicate the battery charge status by directly driving two external LEDs. The AAT3690 is available in a Pb-free, thermally-enhanced, space-saving 12-pin 3 x 3mm TDFN package and is rated over the -40C to +85C temperature range. Applications * * * * * * Cellular Telephones Digital Still Cameras Hand-Held PCs MP3 Players Personal Data Assistants (PDAs) Other Lithium-Ion/Polymer Battery-Powered Devices Typical Application Enable EN USB Input BATT+ USB BAT USBSET RSETUSB TS AAT3690 C2 10F BATT- CT CT ADP Input ADP GND ADPSET RSETADP STAT1 STAT2 TEMP Battery Pack Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201893B * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * April 27, 2012 1 DATA SHEET AAT3690 1.0A USB Port/Adapter Li-Ion/Polymer Battery Charger Pin Descriptions Pin # Name Type 1, 10 2 3 4 USB BAT ADP GND In In/Out In Ground 5 EN In 6 TS In/Out 7 8 STAT2 STAT1 Out Out 9 CT In/Out 11 12 EP USBSET ADPSET In/Out In/Out Function USB power supply input. Battery charging and sensing. Adapter power supply input. Ground connection. Enable pin. Logic high enables the IC. When open, this pin is internally pulled up to the higher voltage of ADP and USB inputs. Connect to 10k NTC thermistor. When TS is open, the battery temperature sensing function is disabled. Battery charge status indicator pin to drive an LED: active low, open-drain. Battery charge status indicator pin to drive an LED: active low, open-drain. Timing capacitor to adjust internal watchdog timer. Set maximum charge time for adapter powered CC and CV charge modes. The watchdog timer only sets the timers for adapter battery charging; there is no timeout for the battery charging from the USB input. If timing function is not needed, terminate this pin to ground. Connect a resistor between this pin and GND to set USB charging current. Connect a resistor between this pin and GND to set adapter charging current. Exposed paddle (bottom); connect to GND directly beneath package. Pin Configuration TDFN33-12 (Top View) USB BAT ADP GND EN TS 2 1 12 2 11 3 10 4 9 5 8 6 7 ADPSET USBSET USB CT STAT1 STAT2 Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201893B * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * April 27, 2012 DATA SHEET AAT3690 1.0A USB Port/Adapter Li-Ion/Polymer Battery Charger Absolute Maximum Ratings1 Symbol VP VP VN TJ TLEAD Description USB, ADP, <30ms, Duty Cycle <10% USB, ADP Continuous BAT, USBSEL, USBSET, ADPSET, STAT1, STAT2, TS, CT, EN Operating Junction Temperature Range Maximum Soldering Temperature (at leads) Value -0.3 to 7.0 -0.3 to 6.0 -0.3 to VP + 0.3 -40 to 150 300 Units V C Thermal Information2 Symbol JA PD Description Maximum Thermal Resistance Maximum Power Dissipation Value Units 50 2.0 C/W W 1. Stresses above those listed in Absolute Maximum Ratings may cause permanent damage to the device. Functional operation at conditions other than the operating conditions specified is not implied. Only one Absolute Maximum Rating should be applied at any one time. 2. Mounted on a FR4 board. Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201893B * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * April 27, 2012 3 DATA SHEET AAT3690 1.0A USB Port/Adapter Li-Ion/Polymer Battery Charger Electrical Characteristics1 VADP = 5V, TA = -40C to +85C, unless otherwise noted. Typical values are at TA = 25C. Symbol Description Operation USB, ADP USB Port or Adapter Voltage Range ADP Voltage Level to Disable USB Charging VU_DSBL VUVLO Under-Voltage Lockout Under-Voltage Lockout Hysteresis IOP Operating Current Sleep Mode Current ISLEEP ILeakage Reverse Leakage Current from BAT Pin Voltage Regulation VBAT_EOC End of Charge Voltage Accuracy VBAT/VBAT EOC Voltage Tolerance VRCH Conditions 4.0 4.25 Rising Edge CC Charge Current = 500mA VBAT = 4.25V VBAT = 4V, USB, ADP Pins Open 4.158 Battery Recharge Voltage Threshold VUSB_CHR USB Charge Reduction Regulation Current Regulation ICH Charge Current ICH/ICH Charge Current Regulation Tolerance ADPSET Pin Voltage VADPSET VUSBSET USBSET Pin Voltage KIADP Current Set Factor: ICHARGE/IADPSET KIUSB Current Set Factor: ICHARGE/IUSBSET Charging Devices RDS(ON)A Adapter Charging Transistor On Resistance RDS(ON)U USB Charging Transistor On Resistance Logic Control / Protection VEN(H) Input High Threshold VEN(L) Input Low Threshold TC Constant Current Mode Time Out (ADP mode only) TV Constant Voltage Mode Time Out (ADP mode only) VSTAT Output Low Voltage ISTAT STAT Pin Current Sink Capability VOVP Over-Voltage Protection Threshold IOCP Over-Current Protection Threshold ITS Charge Termination Threshold Current ITERM/ICHG Current Source from TS Pin TS1 TS Hot Temperature Fault TS2 TS Cold Temperature Fault TREG TLOOP_IN TLOOP_OUT TOVSD Min Thermal Loop Regulation Thermal Loop Entering Threshold Thermal Loop Exiting Threshold Over-Temperature Shutdown Threshold 4.3 ADP Input USB Input 4.5 3.0 150 0.75 2.0 1.0 4.2 0.5 VBAT_EOC - 0.1 4.5 100 50 Max Units 5.5 4.7 V V V mV mA A A 1.5 5.0 4.242 0.2 0.4 0.25 0.5 4.64 V 1000 1000 mA % V V 0.35 0.65 1.6 0.4 CCT = 100nF, VADP = 5.5V CCT = 100nF, VADP = 5.5V STAT Pin Sinks 4mA 3.0 3.0 0.4 8.0 4.4 105 Threshold Hysteresis Threshold Hysteresis 70 310 2.2 7.5 80 330 15 2.3 10 90 110 85 145 V % V 10 2.0 2.0 4000 2000 In CC Mode In CC Mode VIN = 5.5V VIN = 5.5V Typ 90 350 2.4 V V Hour Hour V mA V % ICH_CC % A mV V mV C C C C 1. The AAT3690 output charge voltage is specified over the 0 to 70C ambient temperature range; operation over the -40C to +85C temperature range is guaranteed by design. 4 Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201893B * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * April 27, 2012 DATA SHEET AAT3690 1.0A USB Port/Adapter Li-Ion/Polymer Battery Charger Typical Characteristics Battery Voltage vs. Supply Voltage IFASTCHARGE vs. RSET 4.242 4.221 1000 VBAT (V) IFASTCHARGE (mA) 10000 ADP USB 100 USB 4.200 ADP 4.179 4.158 4.5 10 1 10 100 1000 4.75 5 5.25 5.5 Supply Voltage (V) RSET (k) Recharge Voltage vs. Temperature End of Charge Voltage vs. Temperature 4.242 4.14 4.13 4.12 4.221 ADP 4.10 4.09 VBAT (V) VRCH (V) 4.11 USB 4.08 4.07 ADP 4.200 USB 4.179 4.06 4.05 4.04 -50 -25 0 25 50 75 4.158 -50 100 -25 Temperature (C) 1100 540 1080 530 1000 490 980 480 ADP 470 940 460 920 450 0 25 1.0 50 Temperature (C) 75 440 100 0.8 ICH (A) ICH ADP (mA) 500 -25 100 1.2 ICH USB (mA) 510 1020 900 -50 75 (RADPSET = 8.06k ) 520 USB 960 50 Adapter Charging Current vs. Battery Voltage (RADPSET = 8.06k ; RUSBSET = 8.06k) 1040 25 Temperature (C) Fast Charge Current vs. Temperature 1060 0 0.6 0.4 0.2 0.0 2.5 2.9 3.3 3.7 4.1 4.5 Battery Voltage (V) Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201893B * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * April 27, 2012 5 DATA SHEET AAT3690 1.0A USB Port/Adapter Li-Ion/Polymer Battery Charger Typical Characteristics USB Charging Current vs. Battery Voltage Adapter Fast Charge Current vs. Supply Voltage (RADPSET = 8.06k ) 600 1200 500 1000 400 800 ICH (mA) ICH (mA) (RUSBSET = 8.06k ) 300 200 VBAT = 3.3V VBAT = 3.9V 600 VBAT = 3.5V 400 200 100 0 2.5 3 3.5 4 0 4.5 4 4.5 5 Battery Voltage (V) USB Fast Charge Current vs. Supply Voltage (RUSBSET; USB = 8.06k ) 600 (RUSBSET; USB = 8.06k ) 600 VBAT = 3.3V VBAT = 3.9V ICH (mA) ICH (mA) 500 VBAT = 3.5V 300 200 0C 300 200 0 0 4 4.25 4.5 4.75 5 5.25 5.5 5.75 6 4.4 4.5 4.6 Supply Voltage (V) VIL vs. Supply Voltage EN Pin (Falling) 1.4 1.3 -40C 1.1 1.1 1.0 0.9 0.8 0.7 -40C 1.0 0.9 0.8 0.6 0.5 85C 0.5 4.6 4.8 5 5.2 5.4 Supply Voltage (V) 25C 0.7 85C 0.6 5 1.2 25C VIH (V) VIH (V) 4.9 EN Pin (Rising) 1.3 4.4 4.8 Supply Voltage (V) 1.4 4.2 4.7 VIH vs. Supply Voltage 1.2 6 70C 25C 400 100 100 0.4 6 USB Fast Charge Current vs. Supply Voltage 500 400 5.5 Supply Voltage (V) 5.6 5.8 6 0.4 4.2 4.4 4.6 4.8 5 5.2 5.4 5.6 Supply Voltage (V) Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201893B * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * April 27, 2012 5.8 6 DATA SHEET AAT3690 1.0A USB Port/Adapter Li-Ion/Polymer Battery Charger Typical Characteristics USB Charge Current vs. Time Adapter Mode Supply Current vs. ADPSET Resistor (RUSBSET = 8.06k ) 0.8 USB VBUS (200mV/div) 0.7 USB Charge Current (100mA/div) IQ (mA) 0.6 0.5 Constant Current 0.4 0.3 USB Peripheral Current Consumption (100mA/div) 0.2 0.1 0.0 Charge Reduction Mode Activated 1 10 100 0 1000 2 4 8 10 Time (sec) ADPSET Resistor (k ) Counter Timeout vs. Temperature CT Pin Capacitance vs. Counter Timeout (CT = 0.1 F) 0.5 10 8 6 Capacitance (F) Counter Timeout (%) 6 4 2 0 -2 -4 -6 0.4 0.3 Constant Current Timeout 0.2 0.1 -8 -10 -50 -25 0 25 50 75 100 Temperature (C) 0.0 0 2 4 6 8 10 Time (hours) Temperature Sense Output Current vs. Temperature TS Pin Current (A) 88 86 84 82 80 78 76 74 72 -50 -25 0 25 50 75 100 Temperature (C) Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201893B * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * April 27, 2012 7 DATA SHEET AAT3690 1.0A USB Port/Adapter Li-Ion/Polymer Battery Charger Functional Block Diagram Reverse Blocking USB Current Compare USBSET Charge Reduction Loop CV Charge Control Constant Current UVLO OverTemperature Protect Current Compare ADPSET BAT ADP Reverse Blocking 80A Voltage Sense STAT1 STAT2 TS Window Comparator Charge Status IC enable Watchdog Timer CT EN GND Functional Description The AAT3690 is a highly integrated single-cell lithiumion/polymer battery charger IC designed to operate with USB port and AC adapter inputs, while requiring a minimum number of external components. The AAT3690 precisely regulates battery charge voltage and current for 4.2V lithium-ion/polymer battery cells. The adapter charge input constant current level can be programmed up to 1.0A for rapid charging applications. In the absence of a high-current adapter input source, the AAT3690 can be powered from a USB port VBUS supply. The USB constant charge current can be externally programmed for maximum constant current charge levels up to 1A. The USB mode has an automatic Charge Reduction Loop control to allow users to charge the battery with limited available current from a USB port while maintaining the regulated port voltage. This system assures the battery 8 charge function will not overload a USB port while charging if other system demands also share power with the respective port supply. The USB charge function is automatically disabled when an adapter input power source greater than 4.4V is present. Status monitor output pins are provided to indicate the battery charge status by directly driving two external LEDs. Battery temperature and charge state are fully monitored for fault conditions. In the event of an over-voltage or over-temperature condition, the device will automatically shut down, thus protecting the charging device, control system, and the battery under charge. In addition to internal charge controller thermal protection, the AAT3690 also provides a temperature sense feedback function (TS pin) from the battery to shut down the device in the event the battery exceeds its own thermal limit during charging. Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201893B * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * April 27, 2012 DATA SHEET AAT3690 1.0A USB Port/Adapter Li-Ion/Polymer Battery Charger Charging Operation Regardless of which charge input function is selected (i.e., either the adapter input or USB input), the AAT3690 has three basic modes for the battery charge cycle: constant current/fast charge; constant voltage; and end of charge (see Figure 1). Fast Charge / Constant Current Charging When enabled, the AAT3690 begins constant-current fast charging. The fast charge Constant Current (ICC) amplitude is determined by the charge mode, ADP or USB, and is programmed by the user via the RSETADP and RSETUSB resistors. The AAT3690 remains in constant current charge mode until the battery reaches the voltage regulation point, VBAT. Constant Voltage Charging The system transitions to a constant voltage charging mode when the battery voltage reaches output charge regulation threshold (VBAT) during the constant current fast charge phase. The regulation voltage level is factory programmed to 4.2V (1%). The charge current in the Constant Current Charge Phase constant voltage mode drops as the battery cell under charge reaches its maximum capacity. End of Charge Cycle Termination and Recharge Sequence When the charge current drops to 7.5% of the programmed fast charge current level in the constant voltage mode, the device terminates charging and goes into a standby state. The charger will remain in a standby state until the battery voltage decreases to a level below the battery recharge voltage threshold (VRCH). When the input supply is disconnected or drops below UVLO or EN = 0, the charger will automatically enter power-saving sleep mode. Consuming an ultra-low 2A in sleep mode, the AAT3690 minimizes battery drain when it is not charging. This feature is particularly useful in applications where the input supply level may fall below the battery charge or under-voltage lockout level. In such cases where the AAT3690 input voltage drops, the device will enter the sleep mode and automatically resume charging once the input supply has recovered from its fault condition. Constant Voltage Charge Phase Charge Complete Voltage Regulated Current I = Max CC I = CC/10 Figure 1: Current vs. Voltage Profile During Charging Phases. Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201893B * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * April 27, 2012 9 DATA SHEET AAT3690 1.0A USB Port/Adapter Li-Ion/Polymer Battery Charger System Operation Flowchart ADP Yes Power Select Yes UVLO VP > VUVLO Switch On No No USB ADP Loop Power OnOn Power Reset Reset Sleep Sleep Mode Mode Enable Thermal Loop Enable USB Loop No Timing Fault Conditions Monitor OV, OT Device Temp. Monitor TJ > 110C Yes Yes Expire Yes Battery Temp. Monitor VTS1 < TS < VTS2 Thermal Loop Current Reduction in ADP Charging Mode Shutdown Mode No No Battery Temp. Fault Charge Safety Timer Set No Recharge Test VRCH > VBAT Yes Yes Current Charging Mode Yes Voltage Charging Mode Current Phase Test VEOC > VBAT No Voltage Phase Test IBAT > ITERM Yes No Charge Completed 10 USB Loop USB Loop Current Current Reduction in USB Reduction in USB Charging Mode Charging Mode USB Voltage Regulation Enable USB Voltage Test VUSB < 4.5V Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201893B * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * April 27, 2012 No DATA SHEET AAT3690 1.0A USB Port/Adapter Li-Ion/Polymer Battery Charger Application Information AC Adapter/USB System Power Charging Adapter Mode In the adapter mode, constant current charge levels up to 1.0A can be programmed by the user. The AAT3690 system control will always select the adapter input over the USB supply input whenever adapter voltage is present on the ADP pin. The AAT3690 will operate from the adapter input over a 4.0V to 5.5V range. The constant current fast charge current for the adapter input mode is set by the RSETADP resistor connected between ADPSET and ground. Refer to Table 1 for recommended RSETADP values for a desired constant current charge level. The precise charging function in the adapter mode may be read from the status LEDs. Please refer to the Battery Charge Status Indication discussion in this datasheet for further details. Thermal Loop Control Due to the integrated nature of the linear charging control pass device for the adapter mode, a special thermal loop control system has been employed to maximize charging current under all operating conditions. The thermal management system measures the internal circuit die temperature and reduces the fast charge current when the device exceeds a preset internal temperature control threshold. Once the thermal loop control becomes active, the fast charge current is initially reduced by a factor of 0.44. The initial thermal loop current can be estimated by the following equation: ITLOOP = ICC * 0.44 The thermal loop control re-evaluates the circuit die temperature every three seconds and adjusts the fast charge current back up in small steps to the full fast charge current level or until an equilibrium current is discovered and maximized for the given ambient temperature condition. In the manner the thermal loop controls the system charge level, the AAT3690 will always provide the highest level of constant current in the fast charge mode possible for any given ambient temperature condition. Adapter Input Charge Inhibit and Resume The AAT3690 has an under-voltage lockout and power on reset feature so that if the input supply to the adapter pin drops below the UVLO threshold the charger will sus- pend charging and shut down. When power is re-applied to the adapter pin or the UVLO condition recovers and VADP > VBAT, the system charge control will assess the state of charge on the battery cell and will automatically resume charging in the appropriate mode for the condition of the battery. USB Mode The AAT3690 provides an input for intelligent USB charging. When no voltage is present on the adapter input pin, the charge controller will automatically switch to accepting power from the USB input. The USB charge may be user programmed to any level between 50mA and 1A by selecting the appropriate resistor values for RSETUSB. Refer to Table 1 for recommended RSETUSB values for the desired USB input constant current charge levels. USB Charge Reduction In many instances, product system designers do not know the real properties of a potential USB port used to supply power to the battery charger. Typically, powered USB ports found on desktop and notebook PCs should supply up to 500mA. In the event a USB port being used to supply the charger is unable to provide the programmed fast charge current or if the system under charge must also share supply current with other functions, the AAT3690 will automatically reduce USB fast charge current to maintain port integrity and protect the host system. ICC ADP RSET (k) USB RSET (k) 50 75 100 200 300 400 500 600 700 800 900 1000 N/A N/A 84.5 43.2 28.0 21.0 16.9 13.3 11.5 10.2 9.09 8.06 86.6 57.6 42.2 21.0 13.7 10.2 8.06 6.65 5.62 4.87 4.32 3.83 Table 1: Resistor Values. The USB charge reduction system becomes active when the voltage on the USB input falls below the USB charge reduction threshold, which is typically 4.5V. The charge reduction system will reduce the fast charge current Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201893B * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * April 27, 2012 11 DATA SHEET AAT3690 1.0A USB Port/Adapter Li-Ion/Polymer Battery Charger USB Input Charge Inhibit and Resume The AAT3690 UVLO and power on reset feature will function when the USB input pin voltage level drops below the UVLO threshold. At this point, the charger will suspend charging and shut down. When power is re-applied to the USB pin or the UVLO condition recovers, the system charge control will assess the state of charge on the battery cell and will automatically resume charging in the appropriate mode for the condition of the battery. 10000 IFASTCHARGE (mA) level in a linear fashion until the voltage sensed on the USB input recovers above the charge reduction threshold voltage. 1000 ADP USB 100 10 1 10 100 1000 RSET (k) Figure 2: IFASTCHARGE vs. RSET. Enable / Disable The AAT3690 provides an enable function to control the charger IC on and off. The enable (EN) pin is active high and is internally pulled up to the higher voltage of ADP and USB supplies. When pulled to a logic low level, the AAT3690 will be shut down and forced into the sleep state. Charging will be halted regardless of the battery voltage or charging state. When the device is re-enabled, the charge control circuit will automatically reset and resume charging functions with the appropriate charging mode based on the battery charge state and measured cell voltage. Programming Charge Current The fast charge constant current charge level for both Adapter and USB input modes are programmed with set resistors placed between the ADPSET and USBSET pins and ground. The accuracy of the fast charge is dominated by the tolerance of the set resistor used. For this reason, 1% tolerance metal film resistors are recommended for the set resistor function. ADP fast charge constant current levels from 100mA to 1.0A may be set by selecting the appropriate resistor value from Table 1. The USB charge may be set to any level between 50mA and 1.0A depending upon the system design requirements for a given USB charge application. Refer to Table 1 and Figure 2 for recommended RSETUSB values. 12 Protection Circuitry Programmable Watchdog Timer The AAT3690 contains a watchdog timing circuit for the adapter input charging mode. No watchdog timing functions are active for the USB input mode. Typically, a 0.1F ceramic capacitor is connected between the CT pin and ground. When a 0.1F ceramic capacitor is used, the device will time a shutdown condition if the fast charge mode exceeds three hours. When the device transitions to the constant voltage mode, the timing counter is reset and will time out after three hours and shut down the charger. Mode Time Fast Charge (CC) Time Out Constant Voltage (CV) Mode Time Out 3 hours 3 hours Table 2: Summary for a 0.1F Used for the Timing Capacitor. The CT pin is driven by a constant current source and will provide a linear response to increases in the timing capacitor value. Thus, if the timing capacitor were to be doubled from the nominal 0.1F value, the time-out times would be doubled. If the programmable watchdog timer function is not needed, it may be disabled by connecting the CT pin to ground. The CT pin should not be left floating or unterminated, as this will cause errors in the internal timing control circuit. Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201893B * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * April 27, 2012 DATA SHEET AAT3690 1.0A USB Port/Adapter Li-Ion/Polymer Battery Charger The constant current provided to charge the timing capacitor is very small, and this pin is susceptible to noise and changes in capacitance value. Therefore, the timing capacitor should be physically located on the printed circuit board layout as closely as possible to the CT pin. Since the accuracy of the internal timer is dominated by the capacitance value, 10% tolerance or better ceramic capacitors are recommended. Ceramic capacitor materials such as X7R and X5R type are a good choice for this application. Over-Voltage Protection An over-voltage event is defined as a condition where the voltage on the BAT pin exceeds the maximum battery charge voltage and is set by the over-voltage protection threshold (VOVP). If an over-voltage condition occurs, the AAT3690 charge control will shut down the device until voltage on the BAT pin drops below the overvoltage protection threshold (VOVP). The AAT3690 will resume normal charging operation after the over-voltage condition is removed. During an over-voltage event, the STAT LEDs will report a system fault. Over-Temperature Shutdown The AAT3690 has a thermal protection control circuit which will shut down charging functions should the internal die temperature exceed the preset thermal limit threshold. Battery Temperature Fault Monitoring In the event of a battery over-temperature condition, the charge control will turn off the internal pass device. The STAT LEDs will display a system fault. After the system recovers from a temperature fault, the device will resume charging operation. The AAT3690 checks battery temperature before starting the charge cycle, as well as during all stages of charging. This is accomplished by monitoring the voltage at the TS pin. This system is intended to use negative temperature coefficient (NTC) thermistors, which are typically integrated into the battery package. Most commonly used NTC thermistors used in battery packs are approximately 10k at room temperature (25C). The TS pin has been specifically designed to source 80A of current to the thermistor. The voltage on the TS pin that results from the resistive load should stay within a window from 335mV to 2.32V. If the battery becomes too hot during charging due to an internal fault, the thermistor will heat up and reduce in value, thus pulling the TS pin voltage lower than the TS1 threshold and the AAT3690 will signal the fault condition. If the use of the TS pin function is not required by the system, it can be left open or terminated to ground using a 10k resistor. Battery Charge Status Indication The AAT3690 has two status LED driver outputs. These two LEDs can indicate simple functions such as no battery charge activity, battery charging, charge complete, and charge fault. Status Indicator Display Simple system charging status may be displayed using one or two LEDs in conjunction with the STAT1 and STAT2 pins on the AAT3690. These two pins are simple switches to connect the LED cathodes to ground. It is not necessary to use both display LEDs if a user simply wants to have a single lamp to show "charging" or "not charging." This can be accomplished by using the STAT1 pin and a single LED. Using two LEDs and both STAT pins simply gives the user more information to the charging states. Refer to Table 3 for LED display definitions. The LED anodes should be connected to either VUSB or VADP, depending upon the system design requirements. The LEDs should be biased with as little current as necessary to create reasonable illumination; therefore, a ballast resistor should be placed between the LED cathodes and the STAT1/2 pins. LED current consumption will add to the overall thermal power budget for the device package, so it is wise to keep the LED drive current to a minimum. 2mA should be sufficient to drive most low-cost green or red LEDs. It is not recommended to exceed 8mA for driving an individual status LED. The required ballast resistor value can be estimated using the following formulas: For connection to the adapter supply: VUSBCHR = 2.0V / R12 R12 + R11 Example: RB(STAT1/2) = VADP - VF(LED) ILED(STAT1/2) Note: Red LED forward voltage (VF) is typically 2.0V @ 2mA. Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201893B * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * April 27, 2012 13 DATA SHEET AAT3690 1.0A USB Port/Adapter Li-Ion/Polymer Battery Charger VBAT = Battery voltage as seen at the BAT pin ICC = Maximum constant fast charge current programmed for the application IOP = Quiescent current consumed by the charger IC for normal operation For connection to the USB supply: RB(STAT1) = 5.5V - 2.0V = 1.75k 2mA Example: V - VF(LED) RB(STAT1/2) = USB ILED(STAT1/2) Note: Green LED forward voltage (VF) is typically 3.2V @ 2mA. The status LED display conditions are described in Table 3. Event Description STAT1 STAT2 Charge Disabled or Low Supply Charge Enabled Without Battery Battery Charging Charge Completed Fault Off Flash1 On Off On Off Flash1 Off On On Table 3: Status LED Display Conditions. Thermal Considerations The AAT3690 is offered in a 3x3mm TDFN package which can provide up to 2.0W of power dissipation when it is properly bonded to a printed circuit board and has a maximum thermal resistance of 50C/W. Many considerations should be taken into account when designing the printed circuit board layout, as well as the placement of the charger IC package in proximity to other heat generating devices in a given application design. The ambient temperature around the charger IC will also have an effect on the thermal limits of a battery charging application. The maximum limits that can be expected for a given ambient condition can be estimated by the following discussion: First, the maximum power dissipation for a given situation should be calculated: Eq. 1: PD = [(VIN - VBAT) * ICC + (VIN * IOP)] Where: PD = Total power dissipation by the device VIN = Either VADP or VUSB, depending on which mode is selected Next, the maximum operating ambient temperature for a given application can be estimated based on the thermal resistance of the 3x3 TDFN package when sufficiently mounted to a PCB layout and the internal thermal loop temperature threshold. Eq. 2: TA = TJ - (JA * PD) Where: TA = Ambient temperature in degrees C TJ = Maximum device junction temperature below the thermal loop threshold PD = Total power dissipation by the device JA = Package thermal resistance in C/W Example: For an application where the fast charge current for the adapter mode is set to 0.75A, VADP = 5.0V, and the worst case battery voltage is 3.6V, what is the maximum ambient temperature where the thermal limiting will become active? Given: VADP = 5.0V VBAT = 3.6V ICC = 0.75A IOP = 0.75mA TJ = 110C JA = 50C/W Using Equation 3, calculate the device power dissipation for the stated condition: Eq. 3: PD = (5.0V - 3.6V)(0.75A) + (5.0V * 0.75mA) = 1.05375W The maximum ambient temperature before the AAT3690 thermal loop becomes active can now be calculated using Equation 4: Eq. 4: TA = 110C - (50C/W * 1.05375W) = 57.3125C 1. Flashing rate depends on output capacitance. 14 Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201893B * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * April 27, 2012 DATA SHEET AAT3690 1.0A USB Port/Adapter Li-Ion/Polymer Battery Charger Output Capacitor Therefore, under the stated conditions for this worst case power dissipation example, the AAT3690 will enter the thermal loop and lower the fast charge constant current when the ambient operating temperature rises above 24.8C. The AAT3690 only requires a 1F ceramic capacitor on the BAT pin to maintain circuit stability. This value should be increased to 10F or more if the battery connection is made any distance from the charger output. If the AAT3690 is to be used in applications where the battery can be removed from the charger, such as in the case of desktop charging cradles, an output capacitor greater than 10F may be required to prevent the device from cycling on and off when no battery is present. Capacitor Selection Input Capacitor In general, it is good design practice to place a decoupling capacitor between the ADP and USB pins and ground. An input capacitor in the range of 1F to 22F is recommended. If the source supply is unregulated, it may be necessary to increase the capacitance to keep the input voltage above the under-voltage lockout threshold during device enable and when battery charging is initiated. Printed Circuit Board Layout Considerations For the best results, it is recommended to physically place the battery pack as close to the AAT3690 BAT pin as possible. To minimize voltage drops on the PCB, keep the high current carrying traces adequately wide. For maximum power dissipation of the AAT3690 TDFN package, the metal substrate should be solder bonded to the board. It is also recommended to maximize the substrate contact to the PCB ground plane layer to further increase local heat dissipation. If the AAT3690 adapter input is to be used in a system with an external power supply source, such as a typical AC-to-DC wall adapter, then a CIN capacitor in the range of 10F should be used. A larger input capacitor in this application will minimize switching or power bounce effects when the power supply is "hot plugged." Likewise, a 10F or greater input capacitor is recommended for the USB input to help buffer the effects of USB source power switching, noise, and input cable impedance. ON/OFF J1 1 2 3 DS1 (b) BAV74LT1 USB J2 GRN LED D2 RED LED D1 0 U1 ADP DS1 (a) BAV74LT1 BAT TS C1 10F C2 10F C3 10F R3 10K 5 EN 1 USB STAT2 7 3 ADP STAT1 8 2 BAT USBSET 11 6 TS ADPSET 12 9 CT GND USB 10 4 CT C4 0.1F R4 1.5K R5 1.5K R1 8.06K R2 8.06K AAT3690 Figure 3: AAT3690 Evaluation Board Schematic. Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201893B * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * April 27, 2012 15 DATA SHEET AAT3690 1.0A USB Port/Adapter Li-Ion/Polymer Battery Charger Figure 4: AAT3690 Evaluation Board Top Side Layout. Component Part Number U1 AAT3690IWP-4.2-T1 R1, R2 R3 R4, R5 C1, C2, C3 C4 JP1 JP2 D1 D2 DS1 (a, b) Chip Resistor Chip Resistor Chip Resistor GRM21BR61A106KE19 GRM188R71C104KA01 PRPN401PAEN Chip Resistor CMD15-21SRC/TR8 CMD15-21VGC/TR8 BAV74LT-A Figure 5: AAT3690 Evaluation Board Bottom Side Layout. Description 1.0A USB Port/Adapter Lithium-Ion/ Polymer Battery Charger; 12-Pin 3x3 TDFN Package 8.06K, 1%, 1/4W; 0603 10K, 5%, 1/4W; 0603 1.5K, 5%, 1/4W; 0603 CER 10F 10V 10% X5R 0805 CER 0.1F 16V 10% X7R 0603 Conn. 3-pin Header, 2mm zip 0 Red LED; 1206 Green LED; 1206 Default Diode; SOT23-3 Manufacturer Skyworks Vishay Vishay Vishay Murata Murata Sullins Electronics Vishay Chicago Miniature Lamp Chicago Miniature Lamp On Semi Table 4: AAT3690 Evaluation Board Bill of Materials. 16 Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201893B * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * April 27, 2012 DATA SHEET AAT3690 1.0A USB Port/Adapter Li-Ion/Polymer Battery Charger Ordering Information Package Marking1 Part Number (Tape and Reel)2 TDFN33-12 RUXYY AAT3690IWP-4.2-T1 Skyworks GreenTM products are compliant with all applicable legislation and are halogen-free. For additional information, refer to Skyworks Definition of GreenTM, document number SQ04-0074. Package Information3 TDFN33-12 Index Area 0.43 0.05 0.1 REF C0.3 0.45 0.05 2.40 0.05 3.00 0.05 Detail "A" 3.00 0.05 1.70 0.05 Top View Bottom View 0.23 0.05 Pin 1 Indicator (optional) 0.05 0.05 0.23 0.05 0.75 0.05 Detail "A" Side View All dimensions in millimeters. 1. XYY = assembly and date code. 2. Sample stock is generally held on part numbers listed in BOLD. 3. The leadless package family, which includes QFN, TQFN, DFN, TDFN and STDFN, has exposed copper (unplated) at the end of the lead terminals due to the manufacturing process. A solder fillet at the exposed copper edge cannot be guaranteed and is not required to ensure a proper bottom solder connection. Copyright (c) 2012 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. ("Skyworks") products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks, the Skyworks symbol, and "Breakthrough Simplicity" are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 201893B * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * April 27, 2012 17