SG140A/SG140 POSITIVE FIXED VOLTAGE REGULATOR DESCRIPTION FEATURES The SG140A/140 series of positive regulators offer self contained, fixed-voltage capability with up to 1.5A of load current and input voltage up to 50V (SG140A series only). * Output voltage set internally to 1.5% on SG140A * Input voltage reange to 50V max. on SG140A * Two volt input-output differential * Bandgap reference voltage * Excellent line and load regulation * Foldback current limiting * Thermal overload protection * Voltages available - 5V, 12V, 15V * Voltages Not Recommended For New Designs - 6V, 8V, 18V, 24V These units feature a unique on-chip trimming system to set the output voltages to within 1.5% of nominal on the SG140A series and 2.0% on the SG140 series. The SG140A versions also offer much improved line and load regulation characteristics. Utilizing an improved Bandgap reference design, problems have been eliminated that are normally associated with the Zener Diode references, such as drift in output voltage and large changes in the line and load regulation. All protective features of thermal shutdown, current limiting, and safe-area control have been designed into these units and since these regulators require only a small output capacitor for satisfactory performance, ease of application is assured. Although designed as fixed-voltage regulators, the output voltage can be increased through the use of a simple voltage divider. The low quiescent drain current of the device insures good regulation when this method is used. Product is available in hermetically sealed TO-257 (isolated), TO-3, TO-66, and TO-39 power packages. HIGH RELIABILITY FEATURES - SG140A/140 Available to MIL-STD - 883 Radiation data available LMI level "S" processing available SCHEMATIC DIAGRAM LINFINITY 2/90 Rev 1.4 6/97 Copyright 1997 1 Microelectronics Inc. 11861 Western Avenue Garden Grove, CA 92841 (714) 898-8121 FAX: (714) 893-2570 SG140A/SG140 SERIES POSITIVE REGULATOR ABSOLUTE MAXIMUM RATINGS (Note 1) Device Output Voltage 5V 6V 8V 12V 15V 18V 24V Input Voltage (transient) (Note 3) 50V 50V 50V 50V 50V 50V 50V Input Voltage 35V 35V 35V 35V 35V 35V 40V Operating Junction Temperature Hermetic (K, R, IG - Packages) ................................... 150C Input Voltage Differential (Output shorted to ground) 35V 35V 35V 35V 35V 35V 35V Storage Temperature Range ............................ -65C to 150C Lead Temperature (Soldering, 10 Seconds) ................... 300C Note 1. Values beyond which damage may occur. THERMAL DATA K Package: Thermal Resistance-Junction to Case, JC ................. 3.0C/W Thermal Resistance-Junction to Ambient, JA ............... 35C/W R Package: Thermal Resistance-Junction to Case, JC ................. 5.0C/W Thermal Resistance-Junction to Ambient, JA .............. 40C/W T Package: Thermal Resistance-Junction to Case, JC .................. 15C/W Thermal Resistance-Junction to Ambient, JA ............ 120C/W IG Package: Thermal Resistance-Junction to Case, JC ................. 3.5C/W Thermal Resistance-Junction to Ambient, JA .............. 42C/W L Package: Thermal Resistance-Junction to Case, JC .................. 35C/W Thermal Resistance-Junction to Ambient, JA ............ 120C/W RECOMMENDED OPERATING CONDITIONS Note A. Junction Temperature Calculation: TJ = TA + (PD x JA). Note B. The above numbers for JC are maximums for the limiting thermal resistance of the package in a standard mounting configuration. The JA numbers are meant to be guidelines for the thermal performance of the device/pc-board system. All of the above assume no ambient airflow. (Note 2) Operating Junction Temperature Range: SG140A/140 .................................................. -55C to 150C Note 2. Range over which the device is functional. CHARACTERISTIC CURVES Note 3. Operation at high input voltages is dependent upon load current. When load current is less than 5mA, output will rise out of regulation as inputoiutput differential icreases beyond 30V. Note also from Figure 1, that maximum load current is reduced at high voltages. The 50V input rating of the SG140A series refers to ability to withstnd high line or transient conditions without damage. Since the regulator's maximum current capability is reduced, the output may fall out of regulation at high input voltages under nominal loading. FIGURE 1. PEAK OUTPUT CURRENT VS. INPUT - OUTPUT DIFFERENTIAL LINFINITY 2/90 Rev 1.4 6/97 Copyright 1997 2 Microelectronics Inc. 11861 Western Avenue Garden Grove, CA 92841 (714) 898-8121 FAX: (714) 893-2570 SG140A/SG140 SERIES CHARACTERISTIC CURVES FIGURE 2. MINIMUM INPUT - OUTPUT VOLTAGE VS. LOAD CURRENT POSITIVE REGULATOR (continued) FIGURE 3. RIPPLE REJECTION VS. FREQUENCY FIGURE 4. TEMPERATURE COEFFICIENT OF OUTPUT VOLTAGE APPLICATIONS FIGURE 5 - FIXED OUITPUT REGULATOR FIGURE 6 - CIRCUIT FOR INCREASING OUITPUT VOLTAGE FIGURE 7 - HIGH OUTPUT CIRRENT, SHORT CIRCUIT PROTECTED FIGURE 8 - ADJUTABLE OUITPUT REGULATOR, 7V to 30V LINFINITY 2/90 Rev 1.4 6/97 Copyright 1997 3 Microelectronics Inc. 11861 Western Avenue Garden Grove, CA 92841 (714) 898-8121 FAX: (714) 893-2570 SG140A/SG140 SERIES ELECTRICAL CHARACTERISTICS 5.0V POSITIVE REGULATOR (Note 1) SG140A - 5 (Unless otherwise specified, these specifications apply over full operating ambient temperatures for SG140A-05 with -55C TA 150C, VIN = 10V, IO = 1.0A, CIN = 0. 33F, COUT = 0.1F and are applicable for the K, R, and IG - Power package - only. Low duty cycle pulse testing techniques are used which maintains junction and case temperature equal to the ambient temperature.) Parameter Output Voltage Line Regulation (Note 1) Load Regulation (Note 1) Total Output Voltage Tolerance Quiescent Current Quiescent Current Change Dropout Voltage Peak Output Current Short Circuit Current Ripple Rejection Output Noise Voltage (rms) Long Term Stability Thermal Shutdown Test Conditions IO = 5mA to 1.0A, TJ = 25C VIN = 7.5V to 20V, IO = 500mA VIN = 7.5V to 20V, TJ = 25C VIN = 7.5V to 20V VIN = 8V to 12V, TJ = 25C IO = 5mA to 1.0A IO = 5mA to 1.5A, TJ = 25C IO = 250mA to 750mA, TJ = 25C VIN = 7.5V to 20V, IO = 5mA to 1.0A, P 15W Over Temperature Range TJ = 25C With Line: VIN = 7.5V to 25V, IO = 500mA VIN = 7.5V to 20V, IO = 1A, TJ = 25C With Load: IO = 5mA to 1.0A VO = 100mV, IO = 1A, TJ = 25C TJ = 25C TJ = 25C VIN = 10V, f = 120Hz, TJ = 25C f = 10Hz to 100KHz (Note 2) 1000hrs. at TJ = 125C IO = 5mA SG140A-5 Units Min. Typ. Max. 4.9 5.0 5.1 V 10 mV 3 10 mV 12 mV 4 mV 25 mV 10 25 mV 15 mV 4.8 5.0 2 2.4 2.1 5.2 6.5 6 0.8 0.8 0.5 2.5 68 40 20 175 V mA mA mA mA mA V A A dB V/V mV C SG140 - 5 (Unless otherwise specified, these specifications apply over full operating ambient temperatures for SG140-05 with -55C TA 150C, and VIN = 10V, IO = 500mA, CIN = 0. 33F, COUT = 0.1F and are applicable for the K, R, and IG - Power package - only. Low duty cycle pulse testing techniques are used which maintains junction and case temperature equal to the ambient temperature.) Parameter Output Voltage Line Regulation (Note 1) Load Regulation (Note 1) Total Output Voltage Tolerance Quiescent Current Quiescent Current Change Dropout Voltage Peak Output Current Short Circuit Current Ripple Rejection Output Noise Voltage (rms) Long Term Stability Thermal Shutdown Test Conditions IO = 5mA to 1.0A, TJ = 25C VIN = 8V to 20V VIN = 7V to 25V, TJ = 25C VIN = 8V to 12V, IO = 1.0A VIN = 7.3V to 20V, IO = 1.0A, TJ = 25C IO = 5mA to 1.0A IO = 5mA to 1.5A, TJ = 25C IO = 250mA to 750mA, TJ = 25C VIN = 8V to 20V, IO = 5mA to 1.0A, P 15W IO = 1.0A TJ = 25C With Line: VIN = 8V to 25V VIN = 8V to 20V, IO = 1A, TJ = 25C With Load: IO = 5mA to 1.0A VO = 100mV, IO = 1A, TJ = 25C TJ = 25C TJ = 25C VIN = 10V, f = 120Hz, TJ = 25C f = 10Hz to 100KHz (Note 2) 1000hrs. at TJ = 125C IO = 5mA SG140-5 Units Min. Typ. Max. V 4.8 5.0 5.2 mV 50 mV 50 mV 25 mV 50 50 mV mV 50 mV 25 4.75 5.00 2 2.4 2.1 5.25 7 6 0.8 0.8 0.5 2.5 68 40 20 175 V mA mA mA mA mA V A A dB V/V mV C Note 1. All regulation tests are made at constant junction temperature with low duty cycle testing. 2. This test is guaranteed but is not tested in production. LINFINITY 2/90 Rev 1.4 6/97 Copyright 1997 4 Microelectronics Inc. 11861 Western Avenue Garden Grove, CA 92841 (714) 898-8121 FAX: (714) 893-2570 SG140A/SG140 SERIES ELECTRICAL CHARACTERISTICS 6.0V & 8.0V POSITIVE REGULATOR (Note 1) SG140 - 6 (Unless otherwise specified, these specifications apply over full operating ambient temperatures for SG140-06 with -55C TA 150C, and VIN = 11V, IO = 500mA, CIN = 0. 33F, COUT = 0.1F and are applicable for the K, R, and IG - Power package - only. Low duty cycle pulse testing techniques are used which maintains junction and case temperature equal to the ambient temperature.) Parameter Output Voltage Line Regulation (Note 1) Load Regulation (Note 1) Total Output Voltage Tolerance Quiescent Current Quiescent Current Change Dropout Voltage Peak Output Current Short Circuit Current Ripple Rejection Output Noise Voltage (rms) Long Term Stability Thermal Shutdown Test Conditions IO = 5mA to 1.0A, TJ = 25C VIN = 9V to 21V VIN = 8V to 25V, TJ = 25C VIN = 9V to 13V, IO= 1.0 A VIN = 8.3V to 21V, IO= 1.0 A, TJ = 25C IO = 5mA to 1.0A IO = 5mA to 1.5A, TJ = 25C IO = 250mA to 750mA, TJ = 25C VIN = 9V to 21V, IO = 5mA to 1.0A, P 15W IO= 1.0 A TJ= 25C With Line: VIN = 9V to 25V VIN = 9V to 21V, IO = 1A, TJ = 25C With Load: IO = 5mA to 1.0A VO = 100mV, IO = 1A, TJ = 25C TJ = 25C TJ = 25C VIN = 10V, f = 120Hz, TJ = 25C f = 10Hz to 100KHz (Note 2) 1000hrs. at TJ = 125C IO = 5mA SG140 - 6 Units Min. Typ. Max. 5.75 6.00 6.25 V 60 mV 60 mV 30 mV 60 mV 60 mV 60 mV 30 mV 5.7 6.0 2 2.4 2.1 6.3 7 6 0.8 0.8 0.5 2.5 65 40 24 175 V mA mA mA mA mA V A A dB V/V mV C SG140 - 8 (Unless otherwise specified, these specifications apply over full operating ambient temperatures for SG140-08 with -55C TA 150C, and VIN = 14V, IO = 500mA, CIN = 0. 33F, COUT = 0.1F and are applicable for the K, R, and IG - Power package - only. Low duty cycle pulse testing techniques are used which maintains junction and case temperature equal to the ambient temperature.) Parameter Output Voltage Line Regulation (Note 1) Load Regulation (Note 1) Total Output Voltage Tolerance Quiescent Current Quiescent Current Change Dropout Voltage Peak Output Current Short Circuit Current Ripple Rejection Output Noise Voltage (rms) Long Term Stability Thermal Shutdown Test Conditions IO = 5mA to 1.0A, TJ = 25C VIN = 11V to 23V VIN = 10.5V to 25V, TJ = 25C VIN = 11V to 17V, IO = 1.0A VIN = 10.5V to 23V, IO = 1.0A, TJ = 25C IO = 5mA to 1.0A IO = 5mA to 1.5A, TJ = 25C IO = 250mA to 750mA, TJ = 25C VIN = 11.5V to 23V, IO = 5mA to 1.0A, P 15W IO = 1.0A TJ = 25C With Line: VIN = 11.5V to 25V VIN = 11.5V to 23V, IO = 1A, TJ = 25C With Load: IO = 5mA to 1.0A VO = 100mV, IO = 1A, TJ = 25C TJ = 25C TJ = 25C VIN = 10V, f = 120Hz, TJ = 25C f = 10Hz to 100KHz (Note 2) 1000hrs. at TJ = 125C IO = 5mA SG140 - 8 Units Min. Typ. Max. 7.7 8.0 8.3 V 80 mV 80 mV 40 mV 80 mV 80 mV 80 mV 40 mV 7.6 8.0 2 2.4 2.1 8.4 7 6 0.8 0.8 0.5 2.5 62 40 32 175 V mA mA mA mA mA V A A dB V/V mV C Note 1. All regulation tests are made at constant junction temperature with low duty cycle testing. 2. This test is guaranteed but is not tested in production. LINFINITY 2/90 Rev 1.4 6/97 Copyright 1997 5 Microelectronics Inc. 11861 Western Avenue Garden Grove, CA 92841 (714) 898-8121 FAX: (714) 893-2570 SG140A/SG140 SERIES ELECTRICAL CHARACTERISTICS 12V POSITIVE REGULATOR (Note 1) SG140 A - 12 (Unless otherwise specified, these specifications apply over full operating ambient temperatures for SG140A -12 with -55C TA 150C, and VIN = 19V, IO = 1.0A, CIN = 0. 33F, COUT = 0.1F and are applicable for the K, R, and IG - Power package - only. Low duty cycle pulse testing techniques are used which maintains junction and case temperature equal to the ambient temperature.) Parameter Output Voltage Line Regulation (Note 1) Load Regulation (Note 1) Total Output Voltage Tolerance Quiescent Current Quiescent Current Change Dropout Voltage Peak Output Current Short Circuit Current Ripple Rejection Output Noise Voltage (rms) Long Term Stability Thermal Shutdown Test Conditions IO = 5mA to 1.0A, TJ = 25C VIN = 14.8V to 27V, IO = 500mA VIN = 14.5V to 27V, TJ = 25C VIN = 16V to 22V VIN = 16V to 22V, TJ = 25C IO = 5mA to 1.0A IO = 5mA to 1.5A, TJ = 25C IO = 250mA to 750mA, TJ = 25C VIN = 14.8V to 27V, IO = 5mA to 1.0A, P 15W Over Temperature Range TJ = 25C With Line: VIN = 15V to 30V, IO = 500mA VIN = 14.8V to 27V, IO = 1A, TJ = 25C With Load: IO = 5mA to 1.0A VO = 100mV, IO = 1A, TJ = 25C TJ = 25C TJ = 25C VIN = 10V, f = 120Hz, TJ = 25C f = 10Hz to 100KHz (Note 2) 1000hrs. at TJ = 125C IO = 5mA SG140A - 12 Units Min. Typ. Max. 11.75 12.00 12.25 V 18 mV 4 18 mV 30 mV 9 mV 60 mV 32 mV 19 mV 11.5 12.0 2 2.4 2.1 12.5 6.5 6 0.8 0.8 0.5 2.5 61 40 48 175 V mA mA mA mA mA V A A dB V/V mV C SG140 - 12 (Unless otherwise specified, these specifications apply over full operating ambient temperatures for SG140-12 with -55C TA 150C, and VIN = 19V, IO = 500mA, CIN = 0. 33F, COUT = 0.1F and are applicable for the K, R, and IG - Power package - only. Low duty cycle pulse testing techniques are used which maintains junction and case temperature equal to the ambient temperature.) Parameter Output Voltage Line Regulation (Note 1) Load Regulation (Note 1) Total Output Voltage Tolerance Quiescent Current Quiescent Current Change Dropout Voltage Peak Output Current Short Circuit Current Ripple Rejection Output Noise Voltage (rms) Long Term Stability Thermal Shutdown Test Conditions IO = 5mA to 1.0A, TJ = 25C VIN = 15V to 27V VIN = 14.5V to 30V, TJ = 25C VIN = 16V to 22V, IO = 1.0A VIN = 14.6V to 27V, IO = 1.0A, TJ = 25C IO = 5mA to 1.0A IO = 5mA to 1.5A, TJ = 25C IO = 250mA to 750mA, TJ = 25C VIN = 14.5V to 27V, IO = 5mA to 1.0A, P 15W IO = 1.0A TJ = 25C With Line: VIN = 15V to 30V VIN = 14.5V to 27V, IO = 1A, TJ = 25C With Load: IO = 5mA to 1.0A VO = 100mV, IO = 1A, TJ = 25C TJ = 25C TJ = 25C VIN = 10V, f = 120Hz, TJ = 25C f = 10Hz to 100KHz (Note 2) 1000hrs. at TJ = 125C IO = 5mA SG140 - 12 Units Min. Typ. Max. 11.5 12.0 12.5 V 120 mV 120 mV mV 60 120 mV 120 mV 120 mV mV 60 11.4 12.0 2 2.4 2.1 12.6 7 6 0.8 0.8 0.5 2.5 61 40 48 175 V mA mA mA mA mA V A A dB V/V mV C Note 1. All regulation tests are made at constant junction temperature with low duty cycle testing. 2. This test is guaranteed but is not tested in production. LINFINITY 2/90 Rev 1.4 6/97 Copyright 1997 6 Microelectronics Inc. 11861 Western Avenue Garden Grove, CA 92841 (714) 898-8121 FAX: (714) 893-2570 SG140A/SG140 SERIES ELECTRICAL CHARACTERISTICS 15V POSITIVE REGULATOR (Note 1) SG140 A - 15 (Unless otherwise specified, these specifications apply over full operating ambient temperatures for SG140A -15 with -55C TA 150C, and VIN = 23V, IO = 1.0A, CIN = 0. 33F, COUT = 0.1F and are applicable for the K, R, and IG - Power package - only. Low duty cycle pulse testing techniques are used which maintains junction and case temperature equal to the ambient temperature.) Parameter Output Voltage Line Regulation (Note 1) Load Regulation (Note 1) Total Output Voltage Tolerance Quiescent Current Quiescent Current Change Dropout Voltage Peak Output Current Short Circuit Current Ripple Rejection Output Noise Voltage (rms) Long Term Stability Thermal Shutdown Test Conditions IO = 5mA to 1.0A, TJ = 25C VIN = 17.9V to 30V, IO = 500mA VIN = 7.5V to 30V, TJ = 25C VIN = 20V to 26V VIN = 20V to 26V, TJ = 25C IO = 5mA to 1.0A IO = 5mA to 1.5A, TJ = 25C IO = 250mA to 750mA, TJ = 25C VIN = 17.9V to 30V, IO = 5mA to 1.0A, P 15W Over Temperature Range TJ = 25C With Line: VIN = 17.9V to 30V, IO = 500mA VIN = 17.9V to 30V, IO = 1A, TJ = 25C With Load: IO = 5mA to 1.0A VO = 100mV, IO = 1A, TJ = 25C TJ = 25C TJ = 25C VIN = 10V, f = 120Hz, TJ = 25C f = 10Hz to 100KHz (Note 2) 1000hrs. at TJ = 125C IO = 5mA SG140A - 15 Units Min. Typ. Max. 14.7 15.0 15.3 V 22 mV 22 mV 30 mV 10 mV 75 mV 35 mV 21 mV 14.4 15.0 2 2.4 2.1 15.6 6.5 6 0.8 0.8 0.5 2.5 60 40 60 175 V mA mA mA mA mA V A A dB V/V mV C SG140 - 15 (Unless otherwise specified, these specifications apply over full operating ambient temperatures for SG140-15 with -55C TA 150C, and VIN = 23V, IO = 500mA, CIN = 0. 33F, COUT = 0.1F and are applicable for the K, R, and IG - Power package - only. Low duty cycle pulse testing techniques are used which maintains junction and case temperature equal to the ambient temperature.) Parameter Output Voltage Line Regulation (Note 1) Load Regulation (Note 1) Total Output Voltage Tolerance Quiescent Current Quiescent Current Change Dropout Voltage Peak Output Current Short Circuit Current Ripple Rejection Output Noise Voltage (rms) Long Term Stability Thermal Shutdown IO = 5mA to 1.0A, TJ = 25C VIN = 18.5V to 30V VIN = 17.5V to 30V, TJ = 25C VIN = 20V to 26V, IO = 1.0A VIN = 17.7V to 30V, IO = 1.0A, TJ = 25C IO = 5mA to 1.0A IO = 5mA to 1.5A, TJ = 25C IO = 250mA to 750mA, TJ = 25C SG140 - 15 Units Min. Typ. Max. 14.4 15.0 15.6 V 150 mV 150 mV mV 75 150 mV 150 mV 150 mV mV 75 VIN = 17.5V to 30V, IO = 5mA to 1.0A, P 15W IO = 1.0A TJ = 25C With Line: VIN = 18.5V to 30V VIN = 18.5V to 30V, IO = 1A, TJ = 25C With Load: IO = 5mA to 1.0A VO = 100mV, IO = 1A, TJ = 25C TJ = 25C TJ = 25C VIN = 10V, f = 120Hz, TJ = 25C f = 10Hz to 100KHz (Note 2) 1000hrs. at TJ = 125C IO = 5mA 14.25 15.00 15.75 V 8.5 mA mA 8 1.0 mA mA 1.0 0.5 mA 2 2.5 V 2.4 A 2.1 A dB 54 40 V/V 60 mV 175 C Test Conditions Note 1. All regulation tests are made at constant junction temperature with low duty cycle testing. 2. This test is guaranteed but is not tested in production. LINFINITY 2/90 Rev 1.4 6/97 Copyright 1997 7 Microelectronics Inc. 11861 Western Avenue Garden Grove, CA 92841 (714) 898-8121 FAX: (714) 893-2570 SG140A/SG140 SERIES ELECTRICAL CHARACTERISTICS 18V& 24V POSITIVE REGULATOR (Note 1) SG140 - 18 (Unless otherwise specified, these specifications apply over full operating ambient temperatures for SG140-18 with -55C TA 150C, and VIN = 27V, IO = 500mA, CIN = 0. 33F, COUT = 0.1F and are applicable for the K, R, and IG - Power package - only. Low duty cycle pulse testing techniques are used which maintains junction and case temperature equal to the ambient temperature.) Parameter Output Voltage Line Regulation (Note 1) Load Regulation (Note 1) Total Output Voltage Tolerance Quiescent Current Quiescent Current Change Dropout Voltage Peak Output Current Short Circuit Current Ripple Rejection Output Noise Voltage (rms) Long Term Stability Thermal Shutdown Test Conditions IO = 5mA to 1.0A, TJ = 25C VIN = 21.5V to 33V VIN = 21V to 33V, TJ = 25C VIN = 24V to 30V, IO = 1.0A VIN = 21V to 30V, IO = 1.0A, TJ = 25C IO = 5mA to 1.0A IO = 5mA to 1.5A, TJ = 25C IO = 250mA to 750mA, TJ = 25C VIN = 21V to 33V, IO = 5mA to 1.0A, P 15W IO = 1A TJ = 25C With Line: VIN = 21V to 33V VIN = 21V to 33V, IO = 1A, TJ = 25C With Load: IO = 5mA to 1.0A VO = 100mV, IO = 1A, TJ = 25C TJ = 25C TJ = 25C VIN = 10V, f = 120Hz, TJ = 25C f = 10Hz to 100KHz (Note 2) 1000hrs. at TJ = 125C IO = 5mA SG140 - 18 Units Min. Typ. Max. 17.3 18.0 18.7 V 180 mV 180 mV 90 mV 180 mV 180 mV 180 mV 90 mV 17.1 18.0 2 2.4 2.1 18.9 7 6 0.8 0.8 0.5 2.5 59 40 72 175 V mA mA mA mA mA V A A dB V/V mV C SG140 - 24 (Unless otherwise specified, these specifications apply over full operating ambient temperatures for SG140-24 with -55C TA 150C, and VIN = 33V, IO = 500mA, CIN = 0. 33F, COUT = 0.1F and are applicable for the K, R, and IG - Power package - only. Low duty cycle pulse testing techniques are used which maintains junction and case temperature equal to the ambient temperature.) Parameter Output Voltage Line Regulation (Note 1) Load Regulation (Note 1) Total Output Voltage Tolerance Quiescent Current Quiescent Current Change Dropout Voltage Peak Output Current Short Circuit Current Ripple Rejection Output Noise Voltage (rms) Long Term Stability Thermal Shutdown Test Conditions IO = 5mA to 1.0A, TJ = 25C VIN = 28V to 38V VIN = 27V to 38V, TJ = 25C VIN = 30V to 36V, IO = 1.0A VIN = 27.1V to 35V, IO = 1.0A, TJ = 25C IO = 5mA to 1.0A IO = 5mA to 1.5A, TJ = 25C IO = 250mA to 750mA, TJ = 25C VIN = 27V to 38V, IO = 5mA to 1.0A, P 15W IO = 1.0A TJ = 25C With Line: VIN = 27V to 38V VIN = 28V to 38V, IO = 1A, TJ = 25C With Load: IO = 5mA to 1.0A VO = 100mV, IO = 1A, TJ = 25C TJ = 25C TJ = 25C VIN = 10V, f = 120Hz, TJ = 25C f = 10Hz to 100KHz (Note 2) 1000hrs. at TJ = 125C IO = 5mA SG140 - 24 Units Min. Typ. Max. V 23 24 25 240 mV 240 mV 120 mV 240 mV 240 mV 240 mV 120 mV 22.8 24.0 2 2.4 2.1 25.2 7 6 0.8 0.8 0.5 2.5 56 40 96 175 V mA mA mA mA mA V A A dB V/V mV C Note 1. All regulation tests are made at constant junction temperature with low duty cycle testing. 2. This test is guaranteed but is not tested in production. LINFINITY 2/90 Rev 1.4 6/97 Copyright 1997 8 Microelectronics Inc. 11861 Western Avenue Garden Grove, CA 92841 (714) 898-8121 FAX: (714) 893-2570 SG140A/SG140 SERIES POSITIVE REGULATOR CONNECTION DIAGRAMS & ORDERING INFORMATION Package 3-TERMINAL TO-3 METAL CAN K-PACKAGE Part No. (See Notes Below) Ambient Temperature Range SG140-XXK/883B SG140-XXK Connection Diagram -55C to 125C -55C to 125C VIN 1 2 CASE IS GROUND VOUT 3-TERMINAL TO-66 METAL CAN R-PACKAGE SG140-XXR/883B SG140-XXR -55C to 125C -55C to 125C VIN 1 2 CASE IS GROUND VOUT 3-PIN TO-39 METAL CAN T-PACKAGE SG140-XXT/883B SG140-XXT -55C to 125C -55C to 125C 3-PIN HERMETIC TO-257 IG-PACKAGE (Isolated) SG140A-XXIG/883B SG140A-XXIG SG140-XXIG/883B SG140-XXIG -55C to 125C -55C to 125C -55C to 125C -55C to 125C 20-PIN CERAMIC (LCC) LEADLESS CHIP CARRIER L- PACKAGE SG140-XXL/883B SG140-XXL -55C to 125C -55C to 125C Note 1. 2. 3. 4. VIN 1 VOUT 2 3 Tab is GND (Note 4) 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. GROUND VOUT GROUND VIN N.C. VIN N.C. N.C. N.C. N.C. GROUND N.C. N.C. VOUT 3 2 1 20 19 4 18 5 17 6 16 7 15 8 14 9 10 11 12 13 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. N.C. VOUT N.C. N.C. VOUT SENSE N.C. VIN N.C. N.C. N.C. Contact factory for JAN and DESC product availability. All parts are viewed from the top. "XX" to be replaced by output voltage of specific fixed regulator. Some products will be available in leadless chip carrier (LCC). Consult factory for price and availability. LINFINITY 2/90 Rev 1.4 6/97 Copyright 1997 9 Microelectronics Inc. 11861 Western Avenue Garden Grove, CA 92841 (714) 898-8121 FAX: (714) 893-2570