MODEL 830-004 Power Supply Module DESCRIPTION The 830-004 is a single output isolated DC/DC converter with an input range of 110 to 375 Vdc. This allows the module to operate from any rectified 80 to 265 Vac line, corresponding to line voltages found worldwide. Fixed output voltages between 5 to 24 Vdc are available to suit a variety of applications. Low cost, high reliability and small dimensions are the main characteristics of this design. The use of an advanced PWM provides for stable and efficient operation over a wide load range. FEATURES * * * * * * Continuous 6 watts of output power without use of a heat sink Wide input voltage range from 110 Vdc to 375 Vdc Single fixed regulated output, voltages available from 5 Vdc to 24 Vdc Two sided layout design and SIP package minimized board space requirement Efficient circuit design constructed on a thermally conductive ceramic substrate UL recognition pending APPLICATIONS * * * * * * Provides DC power for PWM and control circuitry for off-line switching power suppliers Provides isolated low DC voltages from AC line voltage levels (rectifier external) Battery chargers for portable personal electronics Industrial controls and line monitoring Stand-alone power supply for small electronics and P controlled appliances Replacement for wall mount transformers and linear regulators 7 Specifications subject to change without notice. Last update: 07/30/02. 7-15 Model 830-004 TYPICAL CONFIGURATION .5A .47F 50V .1F 400V 47F 50V + + AC Line 47F 450V .1F 400V .1 F 50 V .47F 50V APPLICATION NOTES Model 830-004 is a complete DC/DC module based on a flyback circuit topology. Most applications require the addition of output capacitance. The capacitor's voltage rating should be selected in correlation to the output voltage of the 830-004. Choose sufficient capacitance to reduce the output ripple to an acceptable level for the application. A 47F electrolytic should generally be suitable and should be located close to the output pins. To operate from an AC line, a bridge rectifier must be added. A DB104 bridge rectifier or four IN4005 configured as pictured. Diodes should be 600 volts, 1 amp and should be used in conjunction with a 47F input capacitor. Choose the capacitor voltage rating appropriately. 7-16 Model 830-004 ELECTRICAL PARAMETER CONDITIONS MIN. 50% Rated Output Power -5% 20%-80% Rated Output Power Vin min. to max. Input Voltage TYP. MAX. UNITS 375 Vdc * +5% Vdc -8% +8% % chg. from Nom. -4% +4% % 250 mVpp 110 Output Voltage, Nom.* Load Regulation Line Regulation 50% Rated Output Power Output Ripple See Typical Configuration Efficiency 20% Rated Power 50% Rated Power 100% Rated Power Operating Frequency Output Power 6 Operating Temperature 0 55 70 75 % % % 500 KHz W 70 C * Standards available: 5, 6, 9, 12, 15 ,18 and 24 Volts. ELECTRICAL CURVES Efficiency 103 75 Efficiency (%) 85 100 97 94 20 30 40 50 60 70 80 Load (% of 6 Watts) 90 65 55 45 35 100 20 30 40 50 60 70 80 Load (% of 6 Watts) 90 100 Maximum Output Current 1.20 Output Current (A) Vout (% of nominal) Load Regulation 106 1.00 0.80 7 0.60 0.40 0.20 0.00 18 16 14 12 10 8 Output Voltage (V) 7-17 6 Model 830-004 OUTLINE DIMENSIONS (Inch) Vertical Mounting, Through-Hole, SIP 0.50 Max. This module is produced in a 4 lead SIP package to achieve a maximum reduction of required board space. Leads: 1: Vin+ 3: Vout- 2: Vin- 4: Vout+ 1.22Max. 0.35 1.22Max. 1 .040 Ref .175 Typ .300 .300 .200 .200 .010 .020 Horizontal Mounting, Through-Hole, SIP Horizontal Mounting, Surface Mount, SIP 0.35 0.55 Max. 0.35 0.55 Max. ORDERING INFORMATION 830-004 V 05 V Mounting Style: V = Vertical, Thru-Hole H = Horizontal, Thru Hole S = Horizontal, Surface Mount Model Series Voltage Prefix Standard Output Voltages: 5, 6, 9, 12, 15, 18, 24 7-18 Model 830-004