3MTM Four-Wall Header .100" x .100" Latch/Ejector, Straight, Compliant Pin 3000 Series * Military (with 3M's 3518 and N3518 polarizing key) and centerbump polarization * Optional ejector latches * Optional polarizing posts * Mounting holes for securing header to board * Dependable eye-of-the needle pin design * Optional high-temperature insulator * See Regulatory Information Appendix (RIA) for chemical compliance information Date Modified: April 30, 2008 TS-0478-B Sheet 1 of 3 Physical Insulation: Material: Glass Filled Polyester (PBT) Glass Filled Polyester (PCT) Flammability: UL 94V-0 Color: Gray (PBT), Black (PCT) Contact: Material: Copper Alloy Plating: Underplating: 100 " [ 2.54 m ] Nickel Wiping Area: 30 " [ 0.76 m ] Gold Solder Tails: 100 " [ 2.54 m ] Tin Lead or 300u" [7.62 um] Matte Tin (See Ordering Information) Marking: 3M Logo, Part Identification Number and Orientation Triangle Electrical Current Rating: 1 A Insulation Resistance: >1 x 109 at 500 VDC Withstanding Voltage: 1,000 VRMS at Sea Level Environmental Temperature Rating: -55C to +105C UL File No.: E68080 3 Electronic Solutions Division Interconnect Solutions http://www.3M.com/interconnects/ 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 3MTM Four-Wall Header .100" x .100" Latch/Ejector, Straight, Compliant Pin 3000 Series -620T02 Header with Short Ejector/Latch for 3M Sockets without Strain Relief -600T02 Header with No Ejector/Latch .08 [2.0] -630T02 Header with Long Ejector/Latch for 3M sockets with Strain Relief .08 [2.0] .573 .010 [14.55] .424 .010 [10.77] 1.07 Ref [27.2] .68 [17.3] .97 Ref [24.6] A .37 Ref [9.4] .46 Ref [11.7] D .100 2.54 .020 0.51 .28 7.1 REF. .185 4.70 .25 6.4 .34 8.6 .13 3.2 .100 2.54 2X O .100 [2.54] SEE NOTE #2 REF. POSITION #1 B A Notch B (See Table) .025 .002 Sq Typ [0.64] Position 1 Orientation Triangle Notch C (See Table & Note 1) Notch A (See Table & Note 1) A .24 [6.1] .68 [17.3] .30 [7.6] .35 [8.9] .175 .010 [4.44] Section A-A .19 [4.8] .020 [0.51] A .21 [5.3] .16 [4.1] Inch (mm) C Tolerance Unless Noted Notes: 1. Notches A & C will accomodate 3M Polarizing Keys 3518 or N3518. 2. Accepts Rear and Front entry mounting hardware: Rear Entry: #4-24 thread cutting screw 3M Part # 3341-5 (.116 [2.95] dia. mounting hole). Front Entry (Prior to installation of latch): #2-56 Bolt and Nut 3M Part # 3341-6 (.106 [2.69] dia. mounting hole). .0 Inch Electronic Solutions Division Interconnect Solutions http://www.3M.com/interconnects/ .00 .000 .01 .005 [ ] Dimensions for Reference only C 3 .1 TS-0478-B Sheet 2 of 3 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 3MTM Four-Wall Header .100" x .100" Latch/Ejector, Straight, Compliant Pin 3000 Series D Polarizing Notches Provided Insertion platen 3442-00XX 0.865 (21.97) 0.71 (18.0) BC 3442-0048 1.305 (33.15) 1.065 (27.05) 0.91 (23.1) BC 3442-0049 1.405 (35.69) 1.165 (29.59) 1.01 (25.6) ABC 3442-0050 1.76 (44.8) 1.605 (40.77) 1.365 (34.67) 1.21 (30.7) ABC 3442-0051 1.96 (49.9) 1.805 (45.85) 1.565 (39.75) 1.41 (35.8) ABC 3442-0052 3429 2.06 (52.4) 1.905 (48.39) 1.665 (42.29) 1.51 (38.3) ABC 3442-0053 3440 2.26 (57.5) 2.105 (53.47) 1.865 (47.37) 1.71 (43.4) ABC 3442-0054 34 3431 2.46 (62.6) 2.305 (58.55) 2.065 (52.45) 1.91 (48.5) ABC 3442-0055 40 3432 2.76 (70.2) 2.605 (66.17) 2.365 (60.07) 2.21 (56.1) ABC 3442-0056 50 3433 3.26 (82.9) 3.105 (78.87) 2.865 (72.77) 2.71 (68.8) ABC 3442-0057 60 3372 3.76 (95.6) 3.605 (91.57) 3.365 (85.47) 3.21 (81.5) ABC 3442-0058 64 3764 3.96 (100.7) 3.805 (96.65) 3.565 (90.55) 3.41 (86.6) ABC 3442-0059 Dimensions Pin Qty 3M Part Number A B C 10 3793 1.26 (32.1) 1.105 (28.07) 14 3314 1.46 (37.2) 16 3408 1.56 (39.7) 20 3428 24 3627 26 30 .300 Min [7.62] Side to Side Stackability .106 [2.69] or (See Note 2) .116 [2.95] See Note 3 .060 [1.52] Position 1 S T R S T Tail Section .100 .003 [2.54] .100 .003 [2.54] R Compliant Section 4X R .009 Max [0.23] 4X .002 .001 [0.05] Break Edges .352 [8.94] B Mating Area Section R-R R .020 Sym [0.51] Section T-T Recommended Mounting Hole Pattern Section S-S Note: 3. Listed below are the PCB hole sizes and tolerances recommended for use with 3M's compliant pin header. The insertion force is designed not to exceed 40 pounds per pin and the withdrawal force is not less than 10 pounds per pin. 4. Use of snap-in latch/ejectors in either short (N3XXX-650T02XX) or long (N3XXX-660T02XX) styles, installed or shipped separately. (-5 & -6 snap-in latches are dimensionally and functionally equivalent to -2 & -3 roll pin latches) Pin Cross Sections Hole Size for: Preferred Drilled - o.0453 .0005 Acceptable Drilled - o.0453 +.0005 -.0010 After Etchback - o.0460 Max After Plating - .o040 .003 Board thickness - .093 to .150 Plating: .001 Minimum Copper plating thickness .0003 Min Tin plating If ordering Snap-In style latches separately, please use the chart below Short Latch Long Latch Color High Temp (PPA) 3505-30 3505-31 Gray High Temp (PPA) N3505-30B N3505-31B Black Ordering Information X XXXX - 6X0T02XX Prefix: Blank = Std.Temp Gray (PBT): (TC Plating Req'd) N = High Temp Black (PCT) (RB Plating Req'd) Plating suffix: TC = 30 " Gold w/Tin-Lead Tails (App. E2 & C2 Apply) RB = 30 " Gold w/Matte Tin Tails (App. E1 & C1 Apply) 3M Part Number Assembly Equipment: Use 3442-00XX platen (see chart above) and appropriate commercial arbor press to press header into pc board. 3 Electronic Solutions Division Interconnect Solutions http://www.3M.com/interconnects/ Latch/Ejector System: 0 = No latch/ejectors 2 = Short latch/ejectors 3 = Long latch/ejectors 5 = Short, Snap-In Latch/Ejectors 6 = Long, Snap-In Latch/Ejectors TS-0478-B Sheet 3 of 3 3M is a trademark of 3M Company. For technical, sales or ordering information call 800-225-5373 Regulatory Information Appendix 3M Electronic Solutions Division/Interconnect EUROPE Appendix E1: European Union RoHS Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as amended by EU Commission Decision 2005/618/EC. This product is RoHS Compliant 2005/95/EC. "RoHS Compliant 2005/95/EC" means that the product or part ("Product") does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information represents 3M's best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M's Regulatory Information Appendix, then 3M's entire liability and Buyer's exclusive remedy will be in accordance with the Warranty stated below. Appendix E2: European Union RoHS Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as amended by EU Commission Decision 2005/618/EC. This product contains lead in the compliant pin area in excess of the maximum concentration value allowed but is compliant by exemption under EU Commission Decision 2005/747/EC. "RoHS Compliant 2005/95/EC" means that the product or part ("Product") does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information represents 3M's best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M's Regulatory Information Appendix, then 3M's entire liability and Buyer's exclusive remedy will be in accordance with the Warranty stated below. Appendix E3: European Union RoHS Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment as amended by Commission Decision 2005/618/EC. This product contains lead in the solder tail area in excess of the maximum concentration value allowed. Unless otherwise stated by 3M in writing, this information represents 3M's best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M's Regulatory Information Appendix, then 3M's entire liability and Buyer's exclusive remedy will be in accordance with the Warranty stated below. Appendix E4: European Union RoHS Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as amended by EU Commission Decision 2005/618/EC. This product contains decaBDE in the insulating material in excess of the maximum concentration value allowed but is compliant by exemption under EU Commission Decision 2005/717/EC. "RoHS Compliant 2005/95/EC" means that the product or part ("Product") does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information represents 3M's best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M's Regulatory Information Appendix, then 3M's entire liability and Buyer's exclusive remedy will be in accordance with the Warranty stated below.product Warranty stated below. RIA-2217A-D Appendix E5: European Union RoHS Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment, as amended by EU Commission Decision 2005/618/EC. This product contains lead in excess of the maximum concentration value allowed but is compliant by exemption under Item 6 of the Annex to the Directive. "RoHS Compliant 2005/95/EC" means that the product or part ("Product") does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this information represents 3M's best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M's Regulatory Information Appendix, then 3M's entire liability and Buyer's exclusive remedy will be in accordance with the Warranty stated below. CHINA Appendix C1: China RoHS Electronic Industry Standard of the People's Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products. This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that the product or part does not contain any of the following substances in excess of the following maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this information represents 3M's best knowledge and belief based upon information provided by third party suppliers to 3M. In the event any product is proven not to conform with 3M's Regulatory Information Appendix, then 3M's entire liability and Buyer's exclusive remedy will be in accordance with the Warranty stated below. Appendix C2: China RoHS Electronic Industry Standard of the People's Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products. This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that the product or part does contain a substance, as detailed in the chart below, in excess of the following maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this information represents 3M's best knowledge and belief based upon information provided by third party suppliers to 3M. The numerical reference in the symbol above should not be construed as a representation regarding the product's life or an extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform with 3M's Regulatory Information Appendix, then 3M's entire liability and Buyer's exclusive remedy will be in accordance with the product Warranty stated below. RIA-2217A-D Appendix C3: China RoHS Electronic Industry Standard of the People's Republic of China, SJ/T11363-2006, Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products. This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006, means that the product or part does contain a substance, as detailed in the chart below, in excess of the following maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise stated by 3M in writing, this information represents 3M's best knowledge and belief based upon information provided by third party suppliers to 3M. The numerical reference in the symbol above should not be construed as a representation regarding the product's life or an extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform with 3M's Regulatory Information Appendix, then 3M's entire liability and Buyer's exclusive remedy will be in accordance with the product Warranty stated below. Important Notice All statements, technical information, and recommendations related to 3M's products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M's current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M. Warranty; Limited Remedy; Limited Liability. This product will be free from defects in material and manufacture for a period of 90 days from the time of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M's option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted. 3M Electronic Solutions Division 6801 River Place Blvd. Austin, TX 78726-9000 U.S.A. 1-800-225-5373 www.3m.com/interconnects Please recycle. Printed in USA. (c) 3M 2008. All rights reserved. RIA-2217A-D 3M is a trademark of 3M Company.