MC14051B, MC14052B, MC14053B Analog Multiplexers/Demultiplexers The MC14051B, MC14052B, and MC14053B analog multiplexers are digitally-controlled analog switches. The MC14051B effectively implements an SP8T solid state switch, the MC14052B a DP4T, and the MC14053B a Triple SPDT. All three devices feature low ON impedance and very low OFF leakage current. Control of analog signals up to the complete supply voltage range can be achieved. * * * * * * * * * http://onsemi.com MARKING DIAGRAMS 16 Triple Diode Protection on Control Inputs Switch Function is Break Before Make Supply Voltage Range = 3.0 Vdc to 18 Vdc Analog Voltage Range (VDD - VEE) = 3.0 to 18 V Note: VEE must be VSS Linearized Transfer Characteristics Low-noise - 12 nV/Cycle, f 1.0 kHz Typical Pin-for-Pin Replacement for CD4051, CD4052, and CD4053 For 4PDT Switch, See MC14551B For Lower RON, Use the HC4051, HC4052, or HC4053 High-Speed CMOS Devices PDIP-16 P SUFFIX CASE 648 1 16 SOIC-16 D SUFFIX CASE 751B Parameter Value Unit VDD DC Supply Voltage (Referenced to VEE, VSS VEE) -0.5 to +18.0 V Vin, Vout Input or Output Voltage Range (DC or Transient) (Referen- ced to VSS for Control Inputs and VEE for Switch I/O) -0.5 to VDD + 0.5 V Iin Input Current (DC or Transient) per Control Pin 10 mA ISW Switch Through Current 25 mA PD Power Dissipation, per Package (Note 2.) 500 mW TA Ambient Temperature Range -55 to +125 C Tstg Storage Temperature Range -65 to +150 C TL Lead Temperature (8-Second Soldering) 260 C 140xxB AWLYWW 1 16 TSSOP-16 DT SUFFIX CASE 948F MAXIMUM RATINGS (Note 1.) Symbol MC140xxBCP AWLYYWW 14 0xxB ALYW 1 16 SOEIAJ-16 F SUFFIX CASE 966 MC140xxB ALYW 1 xx A WL, L YY, Y WW, W = Specific Device Code = Assembly Location = Wafer Lot = Year = Work Week ORDERING INFORMATION 1. Maximum Ratings are those values beyond which damage to the device may occur. 2. Temperature Derating: Plastic "P and D/DW" Packages: - 7.0 mW/C From 65C To 125C See detailed ordering and shipping information in the package dimensions section on page 12 of this data sheet. This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high-impedance circuit. For proper operation, Vin and Vout should be constrained to the range VSS (Vin or Vout) VDD. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either VSS, VEE or VDD). Unused outputs must be left open. Semiconductor Components Industries, LLC, 2000 August, 2000 - Rev. 4 1 Publication Order Number: MC14051B/D MC14051B, MC14052B, MC14053B MC14051B 8-Channel Analog Multiplexer/Demultiplexer CONTROLS SWITCHES IN/OUT 6 11 10 9 13 14 15 12 1 5 2 4 INHIBIT A B C X0 X1 X 3 X2 COMMON X3 OUT/IN X4 X5 X6 X7 MC14052B Dual 4-Channel Analog Multiplexer/Demultiplexer CONTROLS SWITCHES IN/OUT INHIBIT A X B X0 X1 X2 X3 Y0 Y Y1 6 10 9 12 14 15 11 1 5 2 4 MC14053B Triple 2-Channel Analog Multiplexer/Demultiplexer CONTROLS 13 COMMONS OUT/IN 3 Y2 Y3 SWITCHES IN/OUT INHIBIT X A B C X0 Y X1 Y0 Y1 Z Z0 Z1 6 11 10 9 12 13 2 1 5 3 COMMONS OUT/IN 15 4 VDD = PIN 16 VSS = PIN 8 VEE = PIN 7 VDD = PIN 16 VSS = PIN 8 VEE = PIN 7 VDD = PIN 16 VSS = PIN 8 VEE = PIN 7 14 Note: Control Inputs referenced to VSS, Analog Inputs and Outputs reference to VEE. VEE must be VSS. PIN ASSIGMENT MC14051B MC14052B MC14053B X4 1 16 VDD Y0 1 16 VDD Y1 1 16 VDD X6 2 15 X2 Y2 2 15 X2 Y0 2 15 Y X 3 14 X1 Y 3 14 X1 Z1 3 14 X X7 4 13 X0 Y3 4 13 X Z 4 13 X1 X5 5 12 X3 Y1 5 12 X0 Z0 5 12 X0 INH 6 11 A INH 6 11 X3 INH 6 11 A VEE 7 10 B VEE 7 10 A VEE 7 10 B VSS 8 9 C VSS 8 9 B VSS 8 9 C http://onsemi.com 2 MC14051B, MC14052B, MC14053B IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIII IIII II IIIIIII IIIII IIIIIII IIIII II IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIII IIII II IIIIIII III III II IIII III III III II IIIII IIIIIII IIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIII IIII II IIIIIII III III II IIII III III III II IIIIIIII IIII II IIIIIII III III II IIII III III III II IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIII IIII II IIIIIII III III II IIII III III III II IIIIIIII IIII II IIIIIII III III II IIII III III III II IIIIIIII IIII IIIIIII III III IIII III III III II II II IIIIIIII IIII IIIIIII III III IIII III III III II II II II IIIIIIIIIIIIIII II IIIIIIII IIII IIIIIII III III IIII III III III II IIIIIIII IIII II IIIIIII IIIIIIIIIIIIIII II IIIIIIII IIII IIIIIII IIIIIIIIIIIIIII II II IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIII IIII IIIIIII IIIIIIIIIIIIIII II II IIIIIIII IIII II IIIIIII III III II IIII III III III II IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIII IIIIII IIIIIII III IIIII IIII III III IIIII II II II IIIIIIII IIII IIIIIII III III IIII III III III IIIIIIII IIII II IIIIIII III III II IIII III III III II IIIIIIII IIII IIIIIII III III IIII III III III II II II II II II IIIIIIII IIII IIIIIII III III IIII III III III IIIIIIII IIII II IIIIIII III III II IIII III III III II IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIII IIII II IIIIIII III III II IIII III III III II IIIIIIII IIII II IIIIIII III III II IIII III III III II IIIIIIII IIII IIIIIII III III IIII III III III II II II II II IIII II IIIIIIII IIII IIIIIII III III IIII III III III IIIIIIII IIII II IIIIIII III III II IIII III III III II IIIIIIII IIII IIIIIII III III IIII III III III II II II IIIIIIII IIII II IIIIIII III III II IIII III III III II IIIIIIII IIII II IIIIIII III III II IIII III III III II IIIIIIII IIII IIIIIII III III IIII III III III II II II II II II IIIIIIII IIII IIIIIII III III IIII III III III IIIIIIII IIII II IIIIIII III III II IIII III III III II IIIIIIII IIII IIIIIII III III IIII III III III II II II IIIIIIII IIII II IIIIIII III III II IIII III III III II IIIIIIII IIII IIIIIII III III IIII III III III II II II IIIIIIII IIII IIIIIII III III IIII III III III II II II IIIIIIII IIII II IIIIIII III III II IIII III III III II IIIIIIII IIII II IIIIIII III III II IIII III III III II IIIIIIII IIII IIIIIII III III IIII III III III II II II II II II IIIIIIII IIII IIIIIII III III IIII III III III IIIIIIII IIIIII IIIIIII III IIIII IIII III III IIIII IIIIIIII IIII IIIIIII III III IIII III III III II II II ELECTRICAL CHARACTERISTICS - 55C Characteristic Symbol VDD Test Conditions 25C 125C Min Max Min Typ (3.) Max Min Max Unit SUPPLY REQUIREMENTS (Voltages Referenced to VEE) Power Supply Voltage Range VDD -- VDD - 3.0 VSS VEE 3.0 18 3.0 -- 18 3.0 18 V Quiescent Current Per Package IDD 5.0 10 15 Control Inputs: Vin = VSS or VDD, Switch I/O: VEE VI/O VDD, and Vswitch 500 mV (4.) -- -- -- 5.0 10 20 -- -- -- 0.005 0.010 0.015 5.0 10 20 -- -- -- 150 300 600 A ID(AV) 5.0 10 15 TA = 25C only (The channel component, (Vin - Vout)/Ron, is not included.) Total Supply Current (Dynamic Plus Quiescent, Per Package A (0.07 A/kHz) f + IDD (0.20 A/kHz) f + IDD (0.36 A/kHz) f + IDD Typical CONTROL INPUTS -- INHIBIT, A, B, C (Voltages Referenced to VSS) Low-Level Input Voltage VIL 5.0 10 15 Ron = per spec, Ioff = per spec -- -- -- 1.5 3.0 4.0 -- -- -- 2.25 4.50 6.75 1.5 3.0 4.0 -- -- -- 1.5 3.0 4.0 V High-Level Input Voltage VIH 5.0 10 15 Ron = per spec, Ioff = per spec 3.5 7.0 11 -- -- -- 3.5 7.0 11 2.75 5.50 8.25 -- -- -- 3.5 7.0 11 -- -- -- V Input Leakage Current Iin 15 Vin = 0 or VDD -- 0.1 -- 0.00001 0.1 -- 1.0 A Input Capacitance Cin -- -- -- -- 5.0 7.5 -- -- pF SWITCHES IN/OUT AND COMMONS OUT/IN -- X, Y, Z (Voltages Referenced to VEE) Recommended Peak-to-Peak Voltage Into or Out of the Switch VI/O -- Channel On or Off 0 VDD 0 -- VDD 0 VDD VPP Recommended Static or Dynamic Voltage Across the Switch (4.) (Figure 5) Vswitch -- Channel On 0 600 0 -- 600 0 300 mV VOO -- Vin = 0 V, No Load -- -- -- 10 -- -- -- V Ron 5.0 10 15 Vswitch 500 mV Vin = VIL or VIH (Control), and Vin = 0 to VDD (Switch) -- -- -- 800 400 220 -- -- -- 250 120 80 1050 500 280 -- -- -- 1200 520 300 Ron 5.0 10 15 -- -- -- 70 50 45 -- -- -- 25 10 10 70 50 45 -- -- -- 135 95 65 Ioff 15 Vin = VIL or VIH (Control) Channel to Channel or Any One Channel -- 100 -- 0.05 100 -- 1000 nA Capacitance, Switch I/O CI/O -- Inhibit = VDD -- -- -- 10 -- -- -- pF Capacitance, Common O/I CO/I -- Inhibit = VDD (MC14051B) (MC14052B) (MC14053B) -- -- -- -- -- -- -- -- -- 60 32 17 -- -- -- -- -- -- -- -- -- Pins Not Adjacent Pins Adjacent -- -- -- -- -- -- 0.15 0.47 -- -- -- -- -- -- Output Offset Voltage ON Resistance ON Resistance Between Any Two Channels in the Same Package Off-Channel Leakage Current (Figure 10) Capacitance, Feedthrough (Channel Off) CI/O -- -- (4.) pF pF 3. Data labeled "Typ" is not to be used for design purposes, but is intended as an indication of the IC's potential performance. 4. For voltage drops across the switch (Vswitch) > 600 mV ( > 300 mV at high temperature), excessive VDD current may be drawn, i.e. the current out of the switch may contain both VDD and switch input components. The reliability of the device will be unaffected unless the Maximum Ratings are exceeded. (See first page of this data sheet.) http://onsemi.com 3 MC14051B, MC14052B, MC14053B IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIII IIIII IIIII IIIII IIIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIII IIIII IIIII IIIII IIIII III IIIIIIIIIIIIIII IIIII IIIII IIIII IIIII III IIIIIIIIIIIIIII IIIII IIIII IIIII IIIII III IIIIIIIIIIIIIII IIIII IIIII IIIII IIIII III IIIIIIIIIIIIIII IIIII IIIII IIIII IIIII III IIIIIIIIIIIIIII IIIII IIIII IIIII IIIII III IIIIIIIIIIIIIII IIIII IIIII IIIII IIIII III IIIIIIIIIIIIIII IIIII IIIII IIIII IIIII III IIIIIIIIIIIIIII IIIII IIIII IIIII IIIII III IIIIIIIIIIIIIII IIIII IIIII IIIII IIIII III IIIIIIIIIIIIIII IIIII IIIII IIIII IIIII III IIIIIIIIIIIIIII IIIII IIIII IIIII IIIII III IIIIIIIIIIIIIII IIIII IIIII IIIII IIIII III IIIIIIIIIIIIIII IIIII IIIII IIIII IIIII III IIIIIIIIIIIIIII IIIII IIIII IIIII IIIII III IIIIIIIIIIIIIII IIIII IIIII IIIII IIIII III IIIIIIIIIIIIIII IIIII IIIII IIIII IIIII III IIIIIIIIIIIIIII IIIII IIIII IIIII IIIII III IIIIIIIIIIIIIII IIIII IIIII IIIII IIIII III IIIIIIIIIIIIIII IIIII IIIII IIIII IIIII III IIIIIIIIIIIIIII IIIII IIIII IIIII IIIII III IIIIIIIIIIIIIII IIIII IIIII IIIII IIIII III IIIIIIIIIIIIIII IIIII IIIII IIIII IIIII III IIIIIIIIIIIIIII IIIII IIIII IIIII IIIII III IIIIIIIIIIIIIII IIIII IIIII IIIII IIIII III IIIIIIIIIIIIIII IIIII IIIII IIIII IIIII III IIIIIIIIIIIIIII IIIII IIIII IIIII IIIII III IIIIIIIIIIIIIII IIIII IIIII IIIII IIIII III IIIIIIIIIIIIIII IIIII IIIII IIIII IIIII III IIIIIIIIIIIIIII IIIII IIIII IIIII IIIII III IIIIIIIIIIIIIII IIIII IIIII IIIII IIIII III IIIIIIIIIIIIIII IIIII IIIII IIIII IIIII III IIIIIIIIIIIIIII IIIII IIIII IIIII IIIII III IIIIIIIIIIIIIII IIIII IIIII IIIII IIIII III IIIIIIIIIIIIIII IIIII IIIII IIIII IIIII III IIIIIIIIIIIIIII IIIII IIIII IIIII IIIII III IIIIIIIIIIIIIII IIIII IIIII IIIII IIIII III IIIIIIIIIIIIIII IIIII IIIII IIIII IIIII III ELECTRICAL CHARACTERISTICS (5.) (CL = 50 pF, TA = 25C) (VEE VSS unless otherwise indicated) Characteristic Propagation Delay Times (Figure 6) Switch Input to Switch Output (RL = 10 k) MC14051 tPLH, tPHL = (0.17 ns/pF) CL + 26.5 ns tPLH, tPHL = (0.08 ns/pF) CL + 11 ns tPLH, tPHL = (0.06 ns/pF) CL + 9.0 ns Symbol VDD - VEE Vdc Typ (6.) All Types Max tPLH, tPHL ns 5.0 10 15 35 15 12 90 40 30 MC14052 tPLH, tPHL = (0.17 ns/pF) CL + 21.5 ns tPLH, tPHL = (0.08 ns/pF) CL + 8.0 ns tPLH, tPHL = (0.06 ns/pF) CL + 7.0 ns 5.0 10 15 30 12 10 75 30 25 MC14053 tPLH, tPHL = (0.17 ns/pF) CL + 16.5 ns tPLH, tPHL = (0.08 ns/pF) CL + 4.0 ns tPLH, tPHL = (0.06 ns/pF) CL + 3.0 ns 5.0 10 15 25 8.0 6.0 65 20 15 Inhibit to Output (RL = 10 k, VEE = VSS) Output "1" or "0" to High Impedance, or High Impedance to "1" or "0" Level MC14051B Unit ns ns tPHZ, tPLZ, tPZH, tPZL ns 5.0 10 15 350 170 140 700 340 280 MC14052B 5.0 10 15 300 155 125 600 310 250 ns MC14053B 5.0 10 15 275 140 110 550 280 220 ns 5.0 10 15 360 160 120 720 320 240 MC14052B 5.0 10 15 325 130 90 650 260 180 ns MC14053B 5.0 10 15 300 120 80 600 240 160 ns -- 10 0.07 -- % BW 10 17 -- MHz Off Channel Feedthrough Attenuation (Figure 7) RL = 1K, Vin = 1/2 (VDD - VEE) p-p fin = 4.5 MHz -- MC14051B fin = 30 MHz -- MC14052B fin = 55 MHz -- MC14053B -- 10 - 50 -- dB Channel Separation (Figure 8) (RL = 1 k, Vin = 1/2 (VDD-VEE) p-p, fin = 3.0 MHz -- 10 - 50 -- dB Crosstalk, Control Input to Common O/I (Figure 9) (R1 = 1 k, RL = 10 k Control tTLH = tTHL = 20 ns, Inhibit = VSS) -- 10 75 -- mV Control Input to Output (RL = 10 k, VEE = VSS) MC14051B Second Harmonic Distortion (RL = 10K, f = 1 kHz) Vin = 5 VPP Bandwidth (Figure 7) (RL = 1 k, Vin = 1/2 (VDD-VEE) p-p, CL = 50pF 20 Log (Vout/Vin) = - 3 dB) tPLH, tPHL ns 5. The formulas given are for the typical characteristics only at 25C. 6. Data labelled "Typ" is not lo be used for design purposes but In intended as an indication of the IC's potential performance. http://onsemi.com 4 MC14051B, MC14052B, MC14053B VDD VDD VDD IN/OUT OUT/IN VEE VDD LEVEL CONVERTED CONTROL IN/OUT OUT/IN CONTROL VEE Figure 1. Switch Circuit Schematic 16 TRUTH TABLE Control Inputs Select INH6 A11 B10 C9 ON Switches Inhibit C* B A MC14051B 0 0 0 0 0 0 0 0 0 0 1 1 0 1 0 1 X0 X1 X2 X3 0 0 0 0 1 1 1 1 0 0 1 1 0 1 0 1 X4 X5 X6 X7 1 x x x None MC14052B Y0 Y1 Y2 Y3 X0 X1 X2 X3 MC14053B Z0 Z0 Z0 Z0 Y0 Y0 Y1 Y1 X0 X1 X0 X1 Z1 Z1 Z1 Z1 Y0 Y0 Y1 Y1 X0 X1 X0 X1 None VDD BINARY TO 1-OF-8 DECODER WITH INHIBIT LEVEL CONVERTER 8 X013 X114 7 VSS VEE X215 X312 3X X41 X55 X62 X74 None *Not applicable for MC14052 x = Don't Care Figure 2. MC14051B Functional Diagram 16 16 INH6 BINARY TO 1-OF-4 DECODER WITH INHIBIT LEVEL CONVERTER A10 B9 X012 X114 VDD 8 VSS 7 INH6 A11 B10 C9 VEE X215 X311 Y01 Y15 Y22 Y34 BINARY TO 1-OF-2 DECODER WITH INHIBIT LEVEL CONVERTER 8 13X VDD VSS 7 VEE X012 X113 Y02 Y11 Z05 3Y Z13 Figure 3. MC14052B Functional Diagram Figure 4. MC14053B Functional Diagram http://onsemi.com 5 14X 15Y 4Z MC14051B, MC14052B, MC14053B TEST CIRCUITS ON SWITCH CONTROL SECTION OF IC A B C PULSE GENERATOR LOAD V Vout CL RL INH SOURCE VDD Figure 5. V Across Switch VEE VEE VDD Figure 6. Propagation Delay Times, Control and Inhibit to Output A, B, and C inputs used to turn ON or OFF the switch under test. A B C VSS Vout INH RL CL = 50 pF RL A B C ON INH OFF Vout Vin RL VDD - VEE VDD - VEE 2 2 Figure 7. Bandwidth and Off-Channel Feedthrough Attenuation CL = 50 pF Vin Figure 8. Channel Separation (Adjacent Channels Used For Setup) OFF CHANNEL UNDER TEST VDD A B C CONTROL SECTION OF IC Vout RL INH VEE OTHER CHANNEL(S) VEE VDD CL = 50 pF R1 COMMON VEE VDD Figure 9. Crosstalk, Control Input to Common O/I Figure 10. Off Channel Leakage NOTE: See also Figures 7 and 8 in the MC14016B data sheet. http://onsemi.com 6 MC14051B, MC14052B, MC14053B VDD KEITHLEY 160 DIGITAL MULTIMETER 10 k 1 k RANGE VDD X-Y PLOTTER VEE = VSS Figure 11. Channel Resistance (RON) Test Circuit 300 300 250 200 150 TA = 125C 100 25C -55C 50 0 -10 RON , ON" RESISTANCE (OHMS) R ON , ON" RESISTANCE (OHMS) 350 -8.0 -6.0 -4.0 -2.0 0 0.2 4.0 6.0 8.0 250 200 150 25C -55C 50 -8.0 -6.0 -4.0 -2.0 0 0.2 4.0 6.0 Vin, INPUT VOLTAGE (VOLTS) Vin, INPUT VOLTAGE (VOLTS) Figure 12. VDD = 7.5 V, VEE = - 7.5 V Figure 13. VDD = 5.0 V, VEE = - 5.0 V 700 350 600 300 500 400 300 TA = 125C 200 25C 100 0 -10 TA = 125C 100 0 -10 10 R ON , ON" RESISTANCE (OHMS) R ON , ON" RESISTANCE (OHMS) TYPICAL RESISTANCE CHARACTERISTICS 350 -55C -8.0 -6.0 -4.0 -2.0 0 0.2 4.0 6.0 8.0 VDD = 2.5 V 200 150 5.0 V 100 7.5 V 50 -8.0 -6.0 -4.0 -2.0 0 0.2 4.0 6.0 8.0 Vin, INPUT VOLTAGE (VOLTS) Vin, INPUT VOLTAGE (VOLTS) Figure 14. VDD = 2.5 V, VEE = - 2.5 V Figure 15. Comparison at 25C, VDD = -VEE http://onsemi.com 7 10 TA = 25C 250 0 -10 10 8.0 10 MC14051B, MC14052B, MC14053B APPLICATIONS INFORMATION peak. If voltage transients above VDD and/or below VEE are anticipated on the analog channels, external diodes (Dx) are recommended as shown in Figure B. These diodes should be small signal types able to absorb the maximum anticipated current surges during clipping. The absolute maximum potential difference between VDD and VEE is 18.0 V. Most parameters are specified up to 15 V which is the recommended maximum difference between VDD and VEE. Balanced supplies are not required. However, VSS must be greater than or equal to VEE. For example, VDD = + 10 V, VSS = + 5 V, and VEE - 3 V is acceptable. See the Table below. Figure A illustrates use of the on-chip level converter detailed in Figures 2, 3, and 4. The 0-to-5 V Digital Control signal is used to directly control a 9 V p-p analog signal. The digital control logic levels are determined by VDD and VSS. The VDD voltage is the logic high voltage; the VSS voltage is logic low. For the example, VDD = + 5 V = logic high at the control inputs; V SS = GND = 0 V = logic low. The maximum analog signal level is determined by V DD and VEE. The VDD voltage determines the maximum recommended peak above VSS. The VEE voltage determines the maximum swing below VSS. For the example, VDD - VSS = 5 V maximum swing above V SS ; VSS - VEE = 5 V maximum swing below VSS. The example shows a 4.5 V signal which allows a 1/2 volt margin at each +5 V -5 V VDD VSS VEE +4.5 V 9 Vp-p +5 V EXTERNAL CMOS DIGITAL CIRCUITRY ANALOG SIGNAL SWITCH I/O COMMON O/I MC14051B MC14052B MC14053B 0-TO-5 V DIGITAL CONTROL SIGNALS 9 Vp-p ANALOG SIGNAL GND -4.5 V INHIBIT, A, B, C Figure A. Application Example VDD VDD DX DX ANALOG I/O COMMON O/I DX DX VEE VEE Figure B. External Germanium or Schottky Clipping Diodes IIIIIIIIIIIIIIIIIIIIIIIII IIII IIIII IIII IIIIIII IIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIII IIII IIIII IIII IIIIIII IIIIIIIII IIII IIIII IIII IIIIIII IIIIIIIII IIII IIIII IIII IIIIIII IIIIIIIII IIII IIIII IIII IIIIIII IIIIIIIII IIII IIIII IIII IIIIIII IIIIIIIII IIII IIIII IIII IIIIIII IIIIIIIII IIII IIIII IIII IIIIIII IIIIIIIII IIII IIIII IIII IIIIIII IIIIIIIII POSSIBLE SUPPLY CONNECTIONS VDD In Volts VSS In Volts VEE In Volts Control Inputs Logic High/Logic Low In Volts +8 0 -8 + 8/0 + 8 to - 8 = 16 Vp-p +5 0 - 12 + 5/0 + 5 to - 12 = 17 Vp-p +5 0 0 + 5/0 + 5 to 0 = 5 Vp-p +5 0 -5 + 5/0 + 5 to - 5 = 10 Vp-p + 10 +5 -5 + 10/ + 5 + 10 to - 5 = 15 Vp-p http://onsemi.com 8 Maximum Analog Signal Range In Volts MC14051B, MC14052B, MC14053B PACKAGE DIMENSIONS PDIP-16 P SUFFIX PLASTIC DIP PACKAGE CASE 648-08 ISSUE R -A- 16 9 1 8 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. B F C DIM A B C D F G H J K L M S L S -T- SEATING PLANE K H G D M J 16 PL 0.25 (0.010) M T A M 16 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 9 -B- 1 P 8 PL 0.25 (0.010) 8 M B S G R K F X 45 C SEATING PLANE J M D 16 PL 0.25 (0.010) MILLIMETERS MIN MAX 18.80 19.55 6.35 6.85 3.69 4.44 0.39 0.53 1.02 1.77 2.54 BSC 1.27 BSC 0.21 0.38 2.80 3.30 7.50 7.74 0 10 0.51 1.01 SOIC-16 D SUFFIX PLASTIC SOIC PACKAGE CASE 751B-05 ISSUE J -A- -T- INCHES MIN MAX 0.740 0.770 0.250 0.270 0.145 0.175 0.015 0.021 0.040 0.70 0.100 BSC 0.050 BSC 0.008 0.015 0.110 0.130 0.295 0.305 0 10 0.020 0.040 M T B S A S http://onsemi.com 9 DIM A B C D F G J K M P R MILLIMETERS MIN MAX 9.80 10.00 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 BSC 0.19 0.25 0.10 0.25 0 7 5.80 6.20 0.25 0.50 INCHES MIN MAX 0.386 0.393 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 BSC 0.008 0.009 0.004 0.009 0 7 0.229 0.244 0.010 0.019 MC14051B, MC14052B, MC14053B PACKAGE DIMENSIONS TSSOP-16 DT SUFFIX PLASTIC TSSOP PACKAGE CASE 948F-01 ISSUE O 16X K REF 0.10 (0.004) 0.15 (0.006) T U M T U V S S S K EEE CCC CCC EEE K1 2X L/2 16 9 J1 B -U- L SECTION N-N J PIN 1 IDENT. 8 1 N 0.15 (0.006) T U S 0.25 (0.010) A -V- M N NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH. PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 7. DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE -W-. F DETAIL E -W- C 0.10 (0.004) -T- SEATING PLANE H D DETAIL E G http://onsemi.com 10 DIM A B C D F G H J J1 K K1 L M MILLIMETERS MIN MAX 4.90 5.10 4.30 4.50 --1.20 0.05 0.15 0.50 0.75 0.65 BSC 0.18 0.28 0.09 0.20 0.09 0.16 0.19 0.30 0.19 0.25 6.40 BSC 0 8 INCHES MIN MAX 0.193 0.200 0.169 0.177 --0.047 0.002 0.006 0.020 0.030 0.026 BSC 0.007 0.011 0.004 0.008 0.004 0.006 0.007 0.012 0.007 0.010 0.252 BSC 0 8 MC14051B, MC14052B, MC14053B PACKAGE DIMENSIONS SOEIAJ-16 F SUFFIX PLASTIC EIAJ SOIC PACKAGE CASE 966-01 ISSUE O 16 LE 9 Q1 M E HE 1 8 L DETAIL P Z D e VIEW P A A1 b 0.13 (0.005) c M 0.10 (0.004) http://onsemi.com 11 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS D AND E DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS AND ARE MEASURED AT THE PARTING LINE. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 5. THE LEAD WIDTH DIMENSION (b) DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE LEAD WIDTH DIMENSION AT MAXIMUM MATERIAL CONDITION. DAMBAR CANNOT BE LOCATED ON THE LOWER RADIUS OR THE FOOT. MINIMUM SPACE BETWEEN PROTRUSIONS AND ADJACENT LEAD TO BE 0.46 ( 0.018). DIM A A1 b c D E e HE L LE M Q1 Z MILLIMETERS MIN MAX --2.05 0.05 0.20 0.35 0.50 0.18 0.27 9.90 10.50 5.10 5.45 1.27 BSC 7.40 8.20 0.50 0.85 1.10 1.50 10 0 0.70 0.90 --0.78 INCHES MIN MAX --0.081 0.002 0.008 0.014 0.020 0.007 0.011 0.390 0.413 0.201 0.215 0.050 BSC 0.291 0.323 0.020 0.033 0.043 0.059 10 0 0.028 0.035 --0.031 MC14051B, MC14052B, MC14053B ORDERING & SHIPPING INFORMATION: Device ORDERING & SHIPPING INFORMATION: Package Shipping MC14051BCP PDIP-16 2000 Units per Box MC14053BCP PDIP-16 2000 Units per Box MC14053BD SOIC-16 48 Units per Rail MC14051BD SOIC-16 48 Units per Rail MC14053BDR2 SOIC-16 2500 Units / Tape & Reel MC14051BDR2 SOIC-16 2500 Units / Tape & Reel MC14053BDT TSSOP-16 96 Units per Rail MC14051BDT TSSOP-16 96 Units per Rail MC14053BDTEL TSSOP-16 2000 Units / Tape & Reel MC14051BDTEL TSSOP-16 2000 Units / Tape & Reel MC14053BDTR2 TSSOP-16 2500 Units / Tape & Reel MC14051BDTR2 TSSOP-16 2500 Units / Tape & Reel MC14053BF SOEIAJ-16 See Note 7. MC14051BF SOEIAJ-16 See Note 7. MC14053BFEL SOEIAJ-16 See Note 7. MC14051BFEL SOEIAJ-16 See Note 7. MC14052BCP PDIP-16 2000 Units per Box MC14052BD SOIC-16 48 Units per Rail MC14052BDR2 7. For ordering information on the EIAJ version of the SOIC packages, please contact your local ON Semiconductor representative. SOIC-16 2500 Units / Tape & Reel MC14052BDT TSSOP-16 96 Units per Rail MC14052BDTR2 TSSOP-16 2500 Units / Tape & Reel MC14052BF SOEIAJ-16 See Note 7. MC14052BFEL SOEIAJ-16 See Note 7. ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. PUBLICATION ORDERING INFORMATION NORTH AMERICA Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: ONlit@hibbertco.com Fax Response Line: 303-675-2167 or 800-344-3810 Toll Free USA/Canada N. American Technical Support: 800-282-9855 Toll Free USA/Canada CENTRAL/SOUTH AMERICA: Spanish Phone: 303-308-7143 (Mon-Fri 8:00am to 5:00pm MST) Email: ONlit-spanish@hibbertco.com ASIA/PACIFIC: LDC for ON Semiconductor - Asia Support Phone: 303-675-2121 (Tue-Fri 9:00am to 1:00pm, Hong Kong Time) Toll Free from Hong Kong & Singapore: 001-800-4422-3781 Email: ONlit-asia@hibbertco.com JAPAN: ON Semiconductor, Japan Customer Focus Center 4-32-1 Nishi-Gotanda, Shinagawa-ku, Tokyo, Japan 141-0031 Phone: 81-3-5740-2745 Email: r14525@onsemi.com EUROPE: LDC for ON Semiconductor - European Support German Phone: (+1) 303-308-7140 (Mon-Fri 2:30pm to 7:00pm CET) Email: ONlit-german@hibbertco.com French Phone: (+1) 303-308-7141 (Mon-Fri 2:00pm to 7:00pm CET) Email: ONlit-french@hibbertco.com English Phone: (+1) 303-308-7142 (Mon-Fri 12:00pm to 5:00pm GMT) Email: ONlit@hibbertco.com ON Semiconductor Website: http://onsemi.com EUROPEAN TOLL-FREE ACCESS*: 00-800-4422-3781 *Available from Germany, France, Italy, UK For additional information, please contact your local Sales Representative. http://onsemi.com 12 MC14051B/D