Hand Crimp Tool for 093" and Claspcon Pin and Socket and Commoning Crimp Terminals HAND CRIMP TOOL Specification Sheet Order No. 63819-1200 TYPE 4D FEATURES A full cycle ratcheting hand tool ensures complete crimps Ergonomic soft grip handles for comfortable crimping A precision user-friendly terminal locator wire stop holds terminals in the proper crimping position Right and Left handed applications This tool is WHMA-IPCA620 Class 2 compliant as indicated This tool is RoHS compliant, however RoHS compliant is not required SCOPE Products: 2.36mm (.093") Diameter, Standard .093" Pin and Socket Crimp Terminals, 18-22 AWG, Claspcon Pin and Socket Crimp Terminals, 16-24 AWG, and Commoning Terminals, 18-22 AWG. AE Insulation Diameter Strip Length Terminal Order No. Wire Size Loose Piece + Reel AWG mm mm In. mm In. 02-09-2118 02-09-6126 1380 18-22 0.82-0.32 1.52-3.05 .060-.120 3.30-3.80 .130-.150 02-09-6123 39-00-0302 02-09-1118 39-00-0307 1381 02-09-1119 39-00-0308 18-22 0.82-0.32 1.52-3.05 .060-.120 3.30-3.80 .130-.150 02-09-5133 02-09-5142 1457-1 05-02-0048 05-02-0047 18-22 0.82-0.32 1.55-2.59 .061-.102 3.30-3.80 .130-.150 1.50-3.50 .059-.138 3.30-3.80 .130-.150 1881-2 02-08-1102 16-24 1.31-0.22 3.51 Max. .138 Max. 3.30-3.80 .130-.150 1973 02-09-8104 18-22 0.82-0.32 2273 02-09-1123 18-22 0.82-0.32 1.52-3.05 .060-.120 3.30-3.80 .130-.150 4272 02-09-1149 18-22 0.82-0.32 1.52-3.05 .060-.120 3.30-3.80 .130-.150 6271 02-09-1212 18-22 0.82-0.32 1.52-3.05 .060-.120 3.30-3.80 .130-.150 + Customer to cut off terminal from reel: 0.18mm (.007") maximum Cut-off Tab. To Achieve IPC-A-620 Class 2 Crimps, the following wire insulation diameter limits are recommended: 1. Terminal #1881-2 maximum diameter - 3.14mm (.124 inch) 2. Terminal #1973 maximum diameter - 2.85mm (.112 inch) 3. 16 - 20 AWG Profile minimum diameter (all terminals) - 1.70mm (.067 inch) Terminal Series No. AE AE AE Doc No: ATS-638191200 Revision: A Release Date: 01-10-08 Revision Date: 01-10-08 UNCONTROLLED COPY Page 1 of 9 Hand Crimp Tool for 093" and Claspcon Pin and Socket and Commoning Crimp Terminals DEFINITION OF TERMS BRUSH BEND UP BELL MOUTH CONDUCTOR CRIMP INSULATION CRIMP ROLLING TWISTING STRIP LENGTH BEND DOWN CRIMP HEIGHT The above terminal drawing is a generic terminal representation. It is not an image of a terminal listed in the scope. CONDITIONS: After crimping, the conductor profiles should measure the following. Terminal Series No 1380 1381 1457-1 1881-2 1973 2273 4272 6271 Doc No: ATS-638191200 Revision: A Wire Size AWG mm2 18 0.82 20 0.52 22 0.32 18 0.82 20 0.52 22 0.32 18 0.82 20 0.52 22 0.32 16 1.31 18 0.82 20 0.52 22 0.32 24 0.22 18 0.82 20 0.52 22 0.32 18 0.82 20 0.52 22 0.32 18 0.82 20 0.52 22 0.32 18 0.82 20 0.52 22 0.32 Conductor Crimp Insulation Crimp Height (Ref.) Width (Ref.) Height (Ref.) Width (Ref.) 1.48 - 1.58 .058-.062 1.93 .076 2.88 .113 2.59 .102 1.37 - 1.47 .054-.058 1.92 .076 2.70 .106 2.56 .101 1.34 - 1.44 .053-.056 1.91 .075 2.44 .096 2.31 .091 1.48 - 1.58 .058-.062 1.93 .076 2.88 .113 2.59 .102 1.37 - 1.47 .054-.058 1.92 .076 2.70 .106 2.56 .101 1.34 - 1.44 .053-.056 1.91 .075 2.44 .096 2.31 .091 1.48 - 1.58 .058-.062 1.93 .076 2.88 .113 2.59 .102 1.37 - 1.47 .054-.058 1.92 .076 2.70 .106 2.56 .101 1.34 - 1.44 .053-.056 1.91 .075 2.44 .096 2.31 .091 1.52 - 1.62 .060-.064 1.95 .077 2.96 .117 2.63 .104 1.48 - 1.58 .058-.062 1.93 .076 2.88 .113 2.59 .102 1.37 - 1.47 .054-.058 1.92 .076 2.70 .106 2.56 .101 1.34 - 1.44 .053-.056 1.91 .075 2.44 .096 2.31 .091 1.27 - 1.37 .050-.054 1.90 .075 2.30 .091 2.28 .090 1.48 - 1.58 .058-.062 1.93 .076 2.88 .113 2.59 .102 1.37 - 1.47 .054-.058 1.92 .076 2.70 .106 2.56 .101 1.34 - 1.44 .053-.056 1.91 .075 2.44 .096 2.31 .091 1.37 - 1.47 .054-.058 1.92 .076 2.75 .108 2.58 .102 1.27 - 1.37 .050-.054 1.90 .075 2.63 .104 2.48 .098 1.25 - 1.35 .049-.053 1.88 .074 2.35 .093 2.30 .091 1.37 - 1.47 .054-.058 1.92 .076 2.75 .108 2.58 .102 1.27 - 1.37 .050-.054 1.90 .075 2.63 .104 2.48 .098 1.25 - 1.35 .049-.053 1.88 .074 2.35 .093 2.30 .091 1.37 - 1.47 .054-.058 1.90 .076 2.75 .108 2.58 .102 1.27 - 1.37 .050-.054 1.90 .075 2.63 .104 2.48 .098 1.25 - 1.35 ..049-.053 1.88 .074 2.35 .093 2.30 .091 Release Date: 01-10-08 Revision Date: 01-10-08 UNCONTROLLED COPY Page 2 of 9 Hand Crimp Tool for 093" and Claspcon Pin and Socket and Commoning Crimp Terminals Terminal Series No 1380 1381 1457-1 1881-2 1973 2273 4272 6271 Wire Size AWG 18 20 22 18 20 22 18 20 22 16 18 20 22 24 18 20 22 18 20 22 18 20 22 18 20 22 2 mm 0.82 0.52 0.32 0.82 0.52 0.32 0.82 0.52 0.32 1.31 0.82 0.52 0.32 0.22 0.82 0.52 0.32 0.82 0.52 0.32 0.82 0.52 0.32 0.82 0.52 0.32 PULL Force Profile Minimum N Lb.. 16-20 22-24 111.3 25.00 x 66.8 15.00 x 53.4 12.00 x 111.3 25.00 x 66.8 15.00 x 53.4 12.00 x 111.3 25.00 x 66.8 15.00 x 53.4 12.00 x 155.8 35.00 x 111.3 25.00 x 66.8 15.00 x 53.4 12.00 x 35.6 8.00 x 111.3 25.00 x 66.8 15.00 x 53.4 12.00 x 89.0 20.00 x 62.3 14.00 x 44.5 10.00 x 89.0 20.00 x 62.3 14.00 x 44.5 10.00 x 89.0 20.00 x 62.3 14.00 x 44.5 10.00 x Locator Order no. Color 63819-1175 Red 63819-1175 Red 63819-1176 Yellow 63819-1175 Red 63819-1176 (yellow) 63819-1175 Red 63819-1175 Red 63819-1175 Red OPERATION CAUTION: Install only Molex terminals listed above with this tool. Do not crimp hardened objects as damage can occur to the tool or die. HANDLE WILL SPRING OPEN Open the tool by squeezing the handles together. At the end of the closing stroke, the ratchet mechanism will release the handles and the hand tool will spring open. See Figure 1. Crimping Terminals 1. Select the desired terminal listed from the preceding charts, and install the proper locator (See chart above and see Locator Installation on page 5). SQUEEZE HANDLES TOGETHER Figure 1 Doc No: ATS-638191200 Revision: A Release Date: 01-10-08 Revision Date: 01-10-08 UNCONTROLLED COPY Page 3 of 9 Hand Crimp Tool for 093" and Claspcon Pin and Socket and Commoning Crimp Terminals 2. Make sure the center of the locator is in the down position. With the locator attached, push the locator button on the back of the hand tool to bring the locator forward through the tooling. See Figure 2. RELEASE LOCATOR BUTTON LOCATOR IN DOWN POSTION TERMINAL LOCATOR PUSHED THRU TOOLING LOCATOR BUTTON PUSHED IN Figure 2 PUSH ON THE LOCATOR BUTTON Figure 3 TERMINAL 3. While holding in the locator button, load the terminal into the proper nest opening in the locator based on the wire gauge or terminal type markings on the hand tooling. See Figure 3. 4. Release the locator button, allowing the locator to return to the crimping position. 5. Close the tool handle until the first ratchet position engages. See Figure 4. 6. Insert the properly stripped wire through the terminal and against the wire stop. See Figure 5. 7. Crimp the terminal by squeezing the tool handles until the ratchet mechanism cycle has been completed. Release the handles to open the jaws. TOOLING PARTIALLY CLOSED PARTIALLY CLOSE HANDLE OPEN POSITION FIRST RATCHET POSITION WIRE AGAINST THE WIRE STOP TERMINAL Figure 4 WIRE STOP IS PART OF THE LOCATOR PRE-STRIPPED WIRE Figure 5 WIRE TERMINAL Note: The tamper proof ratchet action will not release the tool until it has been fully closed. Doc No: ATS-638191200 Revision: A Release Date: 01-10-08 Revision Date: 01-10-08 UNCONTROLLED COPY Page 4 of 9 Hand Crimp Tool for 093" and Claspcon Pin and Socket and Commoning Crimp Terminals WIRE 8. Remove the crimped terminal from the terminal locator by pulling on the wire. 9. Visually inspect the crimped terminal for proper crimp location. 10. On some large O.D. wires, it may not be possible to insert the wire with the tool partially closed. Those wires should be inserted with the hand tool in the open position. Insert the wire above the terminal in the punch and against the wire stop then close the tool. See Figure 6. WIRE STOP Figure 6 TERMINAL Note: A crimp height chart is provided with this manual as Reference Only. Due to the wide range of wires, strands, insulation diameters, and durometers available, actual crimp height measurements may very slightly. An occasional, destructive, pull force test should be preformed to check hand tool crimp. Pull Force value Must exceed the Minimum pull force specifications listed. Locator Installation See the parts list on the last page of this document for the proper locator order number. Follow the steps below to replace the locator. 1. Open the crimp hand tool. 2. Squeeze gently on the lower area shown in Figure 7A with your thumb and index finger. The lower tabs of the locator should disengage from the hand tool. LOCATOR SQUEEZE HERE JAWS OPEN MAKE SURE CENTER OF LOCATOR IS IN THE DOWN POSITION TOP SLOTS OF HANDTOOL SQUEEZE HERE PULL OPEN TOOLING TOOLING M3 BHCS TOP HOOKS Figure 8 Figure 7B PUSH ON HANDLE Figure 7A LOWER TABS 3. Lift and pull away from the hand tool. The top locator hooks should slip out of the top slots easily. See Figure 7A. Doc No: ATS-638191200 Revision: A Release Date: 01-10-08 Revision Date: 01-10-08 UNCONTROLLED COPY Page 5 of 9 Hand Crimp Tool for 093" and Claspcon Pin and Socket and Commoning Crimp Terminals 4. To reinstall the new locator, make sure the hand tool is in the open position. 5. Press the red insert down as far as it will go as shown in Figure 7B. 6. Holding onto the lower part of the locator with your thumb and index finger, insert the locator top hooks (2) into the hand tool top slots. 7. Rotate the locator down and press the lower tabs into the two bottom slots of the hand tool. To secure the locator into place, the lower tabs must snap into place on the hand tool frame. Right or Left Hand Operation MATCH UP MARKS This hand tool has an added feature that can be converted from a right handed application to a left handed application. It is necessary to reverse the tooling along with the locator if using the left handed application. Follow the steps below: Figure 9 FRONT 1. The locator must be removed before reversing the tooling. 2. Remove the M3 BHCS which is holding the upper tooling. 3. Flip the upper tooling to the opposite side and replace the M3 BHCS Make sure the small markings on the front and back of the hand tool frame match up and are on the outside of the hand tool frame. See Figure 8 and 9. 4. Do the same thing with the lower tooling and tighten the M3 screws. Be sure the small markings line up. 5. Reinstall the locator by following the Instructions in the locator replacement section. Maintenance It is recommended that each operator of the tool be made aware of, and responsible for, the following maintenance steps: BACK LUBRICATION POINTS (BOTH SIDES) LIGHT OIL (EVERY 3 MONTHS OR 5,000 CRIMPS) Figure 10 1. Remove dust, moisture, and other contaminants with a clean brush, or soft, lint free cloth. 2. Do not use any abrasive materials that could damage the tool. 3. Make certain all pins; pivot points and bearing surfaces are protected with a thin coat of high quality machine oil. Do not oil excessively. The tool was engineered for durability but like any other equipment it needs cleaning and lubrication for a maximum service life of trouble free crimping. Light oil (such as 30 weight automotive oil) used at the oil points, every 5,000 crimps or 3 months, will significantly enhance the tool life. 4. Wipe excess oil from hand tool, particularly from crimping area. Oil transferred from the crimping area onto certain terminations may affect the electrical characteristics of an application. 5. When tool is not in use, keep the handles closed to prevent objects from becoming lodged in the crimping dies, and store the tool in a clean, dry area. Doc No: ATS-638191200 Revision: A Release Date: 01-10-08 Revision Date: 01-10-08 UNCONTROLLED COPY RATCHET RELEASE LEVER Figure 11 Page 6 of 9 Hand Crimp Tool for 093" and Claspcon Pin and Socket and Commoning Crimp Terminals Miscrimps or Jams Should this tool ever become stuck or jammed in a partially closed position, Do Not force the handles open or closed. The tool will open easily by pressing up on the ratchet release lever in the movable handle. See Figure 11 RATCHET RELEASE LEVER SQUEEZE THE LINK IN THE HANDLE HOLD THE HAND TOOL IN POSITION How to Adjust Tool Preload (See Figure 10) This hand tool is factory preset to 25-45 LBS. preload. It may be necessary over SETTING the life of the tool to adjust tool handle WHEEL preload force. Listed below are the steps required to adjust the crimping force of the hand tool to obtain proper crimp conditions: Figure 12 1. Hold the hand tool in the palm of your hand as shown in Figure 12. Using the index finger squeeze the link towards the top of the hand tool frame. This will release the preload adjustment wheel. 2. Rotate the setting wheel counter-clockwise (CCW) to increase handle force. The numbers will display higher. To decrease handle force, rotate the setting wheel clockwise (CW). 3. Release the link to lock the setting wheel in place. 4. Check the crimp specifications or conduct a pull test after tool handle preload force is adjusted. Warranty This tool is for electrical terminal crimping purposes only. This tool is made of the best quality materials. All vital components are long life tested. All tools are warranted to be free of manufacturing defects for a period of 30 days. Should such a defect occur, we will repair or exchange the tool free of charge. This repair or exchange will not be applicable to altered, misused, or damaged tools. This tool is designed for hand use only. Any clamping, fixturing, or use of handle extensions voids this warranty. CAUTION: Molex crimp specifications are valid only when used with Molex terminals and tooling. Doc No: ATS-638191200 Revision: A Release Date: 01-10-08 Revision Date: 01-10-08 UNCONTROLLED COPY Page 7 of 9 Hand Crimp Tool for 093" and Claspcon Pin and Socket and Commoning Crimp Terminals CAUTIONS: 1. Manually powered hand tools are intended for low volume or field repair. This tool is NOT intended for production use. Repetitive use of this tool should be avoided. 2. Insulated rubber handles are not protection against electrical shock. 3. Wear eye protection at all times. 4. Use only the Molex terminals specified for crimping with this tool. Certification Molex does not certify or re-certify hand tools but rather supplies the following guidelines for customers to re-certify hand tools. % % % This tool is qualified to pull force only. To re-certify, crimp a terminal to a wire, which has been stripped 12.7mm (1/2") long, so there is no crimping of the insulation. Pull the terminal and wire at a rate no faster than 25mm (1.00") per minute. See the Molex web site for the Quality Crimp Handbook for more information on pull testing. If the tool does not meet minimum pull force values, handle preload should be increased and the pull test rerun, (See How to Adjust Preload). When the hand tool is no longer capable of achieving minimum pull force, it should be taken out of service and replaced. Doc No: ATS-638191200 Revision: A Release Date: 01-10-08 Revision Date: 01-10-08 UNCONTROLLED COPY Page 8 of 9 Hand Crimp Tool for 093" and Claspcon Pin and Socket and Commoning Crimp Terminals PARTS LIST Item Number REF 1 1 2 3 Order Number 63819-1200 63819-1175 63819-1176 63810-0104 63810-0105 Description Hand Crimp Tool Locator Assembly (Red) Locator Assembly (Yellow) Spring, Return Spring, Ratchet Quantity Figure 13 1 1 1 1 2 1 RATCHET RELEASE LEVER Figure 13 Americas Headquarters Lisle, Illinois 60532 U.S.A. 1-800-78MOLEX amerinfo@molex.com Far East North Headquarters Yamato, Kanagawa, Japan 81-462-65-2324 feninfo@molex.com 3 Far East South Headquarters Jurong, Singapore 65-6-268-6868 fesinfo@molex.com European Headquarters Munich, Germany 49-89-413092-0 eurinfo@molex.com Corporate Headquarters 2222 Wellington Ct. Lisle, IL 60532 U.S.A. 630-969-4550 Fax: 630-969-1352 Visit our Web site at http://www.molex.com Doc No: ATS-638191200 Revision: A Release Date: 01-10-08 Revision Date: 01-10-08 UNCONTROLLED COPY Page 9 of 9