LM5010MH/NOPB - NATIONAL SEMICONDUCTOR

VIN

BST

LM5010

VCC

RON / SD

8V - 75V

Input

RON

R1 C2

VOUT

RTN

ISEN

SGND

SHUTDOWN

Product

Folder

Sample &

Buy

Technical

Documents

Tools &

Software

Support &

Community

An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,

intellectual property matters and other important disclaimers. PRODUCTION DATA.

LM5010

SNVS307G –SEPTEMBER 2004–REVISED APRIL 2016

LM5010 High-Voltage 1-A Step-Down Switching Regulator

1 Features

1• Input Voltage Range: 8 V to 75 V

• Valley Current Limit At 1.25 A

• Switching Frequency Can Exceed 1 MHz

• Integrated N-Channel Buck Switch

• Integrated Start-Up Regulator

• No Loop Compensation Required

• Ultra-Fast Transient Response

• Operating Frequency Remains Constant With

Load and Line Variations

• Maximum Duty Cycle Limited During Start-Up

• Adjustable Output Voltage

• Precision 2.5-V Feedback Reference

• Thermal Shutdown

• Exposed Thermal Pad for Improved Heat

Dissipation

2 Applications

• High Efficiency Point-of-Load (POL) Regulator

• Non-Isolated Telecommunications Buck Regulator

• Secondary High Voltage Post Regulator

• Automotive Systems

3 Description

The LM5010 step-down switching regulator features

all the functions needed to implement a low-cost,

efficient, buck bias regulator capable of supplying in

excess of 1-A load current. This high-voltage

regulator contains an N-Channel Buck Switch, and is

available in thermally enhanced 10-pin WSON and

14-pin HTSSOP packages. The hysteretic regulation

scheme requires no loop compensation, resulting in

fast load transient response, and simplifies circuit

implementation. The operating frequency remains

constant with line and load variations due to the

inverse relationship between the input voltage and

the ON-time. The valley current limit detection is set

at 1.25 A. Additional features include: VCC

undervoltage lockout, thermal shutdown, gate drive

undervoltage lockout, and maximum duty cycle

limiter.

Device Information(1)

PART NUMBER PACKAGE BODY SIZE (NOM)

LM5010 WSON (10) 4.00 mm × 4.00 mm

HTSSOP (14) 4.40 mm × 5.00 mm

(1) For all available packages, see the orderable addendum at

the end of the data sheet.

Basic Step-Down Regulator

LM5010

SNVS307G –SEPTEMBER 2004–REVISED APRIL 2016

www.ti.com

Product Folder Links: LM5010

Table of Contents

1 Features.................................................................. 1

2 Applications ........................................................... 1

3 Description............................................................. 1

4 Revision History..................................................... 2

5 Pin Configuration and Functions......................... 3

6 Specifications......................................................... 4

6.1 Absolute Maximum Ratings ...................................... 4

6.2 ESD Ratings.............................................................. 4

6.3 Recommended Operating Conditions....................... 4

6.4 Thermal Information.................................................. 5

6.5 Electrical Characteristics........................................... 5

6.6 Switching Characteristics.......................................... 6

6.7 Typical Characteristics.............................................. 7

7 Detailed Description.............................................. 9

7.1 Overview................................................................... 9

7.2 Functional Block Diagram......................................... 9

7.3 Feature Description................................................... 9

7.4 Device Functional Modes........................................ 14

8 Application and Implementation ........................ 15

8.1 Application Information............................................ 15

8.2 Typical Application.................................................. 15

8.3 Do's and Don'ts....................................................... 21

9 Power Supply Recommendations...................... 22

10 Layout................................................................... 22

10.1 Layout Guidelines ................................................. 22

10.2 Layout Example .................................................... 22

11 Device and Documentation Support................. 23

11.1 Community Resources.......................................... 23

11.2 Trademarks........................................................... 23

11.3 Electrostatic Discharge Caution............................ 23

11.4 Glossary................................................................ 23

12 Mechanical, Packaging, and Orderable

Information........................................................... 23

4 Revision History

NOTE: Page numbers for previous revisions may differ from page numbers in the current version.

Changes from Revision F (February 2013) to Revision G Page

• Added ESD Ratings table, Feature Description section, Device Functional Modes,Application and Implementation

section, Power Supply Recommendations section, Layout section, Device and Documentation Support section, and

Mechanical, Packaging, and Orderable Information section.................................................................................................. 1

Changes from Revision E (February 2013) to Revision F Page

• Changed layout of National Data Sheet to TI format ............................................................................................................. 1

ExposedPad

1NC 14 NC

2SW 13 VIN

3BST 12 VCC

4ISEN 11 RON /SD

5SGND 10 SS

6RTN 9 FB

7NC 8 NC

ExposedPad

1SW 10 VIN

2BST 9 VCC

3ISEN 8 RON /SD

4SGND 7 SS

5RTN 6 FB

LM5010

www.ti.com

SNVS307G –SEPTEMBER 2004–REVISED APRIL 2016

Product Folder Links: LM5010

5 Pin Configuration and Functions

DPR Package

10-Pin WSON

Top View PWP Package

14-Pin HTSSOP

Top View

Pin Functions

PIN I/O DESCRIPTION

NAME WSON HTSSOP

BST 2 3 I Boost pin for bootstrap capacitor: Connect a 0.022-µF capacitor from SW to this pin. The

capacitor is charged from VCC through an internal diode during each OFF-time.

EP — — — Exposed pad

FB 6 9 I Feedback input from the regulated output: Internally connected to the regulation and

overvoltage comparators. The regulation level is 2.5 V.

ISEN 3 4 I Current sense: The recirculating current flows through the internal sense resistor, and out

of this pin to the free-wheeling diode. Current limit is nominally set at 1.25 A.

NC — 1, 7, 8, 14 — No connection

RON/SD 8 11 I ON-time control and shutdown: An external resistor from VIN to this pin sets the buck

switch ON-time. Grounding this pin shuts down the regulator.

RTN 5 6 — Circuit ground: Ground for all internal circuitry other than the current limit detection.

SGND 4 5 — Sense ground: Recirculating current flows into this pin to the current sense resistor.

SS 7 10 I Soft start: An internal 11.5-µA current source charges an external capacitor to 2.5 V,

providing the soft start function.

SW 1 2 O Switching node: Internally connected to the buck switch source. Connect to the inductor,

free-wheeling diode, and bootstrap capacitor.

VCC 9 12 I Output from the startup regulator: Nominally regulates at 7 V. An external voltage (7.5 V

to 14 V) can be applied to this pin to reduce internal dissipation. An internal diode

connects VCC to VIN.

VIN 10 13 I Input supply: Nominal input range is 8 V to 75 V.

LM5010

SNVS307G –SEPTEMBER 2004–REVISED APRIL 2016

www.ti.com

Product Folder Links: LM5010

(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings

only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended

Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

(2) For detailed information on soldering plastic HTSSOP and WSON packages, see Mechanical, Packaging, and Orderable Information.

6 Specifications

6.1 Absolute Maximum Ratings

over operating free-air temperature range (unless otherwise noted)(1)

MIN MAX UNIT

VIN 8 75 V

VIN to GND 76 V

BST to GND 90 V

SW to GND (steady state) –1.5 V

BST to VCC 76 V

BST to SW 14 V

VCC to GND 14 V

SGND to RTN –0.3 0.3 V

SS to RTN –0.3 4 V

VIN to SW 76 V

All other inputs to GND –0.3 7 V

Lead temperature (soldering, 4 s)(2) 260 °C

Junction temperature, TJ–40 150 °C

Storage temperature, Tstg –55 150 °C

(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.

(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.

6.2 ESD Ratings VALUE UNIT

V(ESD) Electrostatic discharge Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1) ±2000 V

Charged-device model (CDM), per JEDEC specification JESD22-C101(2) ±750

6.3 Recommended Operating Conditions

over operating free-air temperature range (unless otherwise noted) MIN MAX UNIT

VIN Input voltage 8 75 V

IOOutput current 1 A

Ext-VCC External bias voltage 8 13 V

TJOperating junction temperature –40 125 °C

LM5010

www.ti.com

SNVS307G –SEPTEMBER 2004–REVISED APRIL 2016

Product Folder Links: LM5010

(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application

report, SPRA953.

6.4 Thermal Information

THERMAL METRIC(1) LM5010

UNITDPR (WSON) PWP (HTSSOP)

10 PINS 14 PINS

RθJA Junction-to-ambient thermal resistance 36 41.1 °C/W

RθJC(top) Junction-to-case (top) thermal resistance 31.9 26.5 °C/W

RθJB Junction-to-board thermal resistance 13.2 22.5 °C/W

ψJT Junction-to-top characterization parameter 0.3 0.7 °C/W

ψJB Junction-to-board characterization parameter 13.5 22.2 °C/W

RθJC(bot) Junction-to-case (bottom) thermal resistance 3 3.3 °C/W

(1) All minimum and maximum limits are specified by correlating the electrical characteristics to process and temperature variations and

applying statistical process control.

(2) The junction temperature (TJin °C) is calculated from the ambient temperature (TAin °C) and power dissipation (PDin Watts) as follows:

TJ= TA+ (PD× RθJA) where RθJA (in °C/W) is the package thermal impedance provided in Thermal Information.

6.5 Electrical Characteristics

Typical values correspond to TJ= 25°C, minimum and maximum limits apply over TJ= –40°C to 125°C, VIN = 48 V, and

RON = 200 kΩ(unless otherwise noted).(1)(2)

PARAMETER TEST CONDITIONS MIN TYP MAX UNIT

VCC REGULATOR

VCCReg VCC regulated output 6.6 7 7.4 V

VIN - VCC ICC = 0 mA, FS< 200 kHz,

7.5 V ≤VIN ≤8 V 1.3 V

VCC output impedance (0 mA ≤ICC ≤5 mA) VIN = 8 V 140 Ω

VIN = 48 V 2.5

VCC current limit VCC = 0 V 10 mA

UVLOVCC VCC undervoltage lockout threshold VCC increasing 5.8 V

UVLOVCC hysteresis VCC decreasing 145 mV

UVLOVCC filter delay 100-mV overdrive 3 µs

IIN operating current Non-switching, FB = 3 V 650 850 µA

IIN shutdown current RON/SD = 0 V 95 200 µA

SOFT-START PIN

Pullup voltage 2.5 V

Internal current source 11.5 µA

CURRENT LIMIT

ILIM Threshold Current out of ISEN 1 1.25 1.5 A

Resistance from ISEN to SGND 130 mΩ

Response time 150 ns

RON/SD PIN

Shutdown threshold Voltage at RON/SD rising 0.35 0.65 1.1 V

Threshold hysteresis Voltage at RON/SD falling 40 mV

HIGH-SIDE FET

RDS(ON) Buck switch ITEST = 200 mA 0.35 0.8 Ω

UVLOGD Gate drive UVLO VBST - VSW Increasing 3 4.3 5 V

UVLOGD Hysteresis 440 mV

REGULATION AND OVERVOLTAGE COMPARATORS (FB PIN)

VREF FB regulation threshold SS pin = steady state 2.45 2.5 2.55 V

FB overvoltage threshold 2.9 V

FB bias current 1 nA

LM5010

SNVS307G –SEPTEMBER 2004–REVISED APRIL 2016

www.ti.com

Product Folder Links: LM5010

Electrical Characteristics (continued)

Typical values correspond to TJ= 25°C, minimum and maximum limits apply over TJ= –40°C to 125°C, VIN = 48 V, and

RON = 200 kΩ(unless otherwise noted).(1)(2)

PARAMETER TEST CONDITIONS MIN TYP MAX UNIT

THERMAL SHUTDOWN

TSD Thermal shutdown temperature 175 °C

Thermal shutdown hysteresis 20 °C

(1) All minimum and maximum limits are specified by correlating the electrical characteristics to process and temperature variations while

applying statistical process control.

6.6 Switching Characteristics

Typical values correspond to TJ= 25°C, minimum and maximum limits apply over TJ= –40°C to 125°C and VIN = 48 V

(unless otherwise noted)(1)

PARAMETER TEST CONDITIONS MIN TYP MAX UNIT

RDS(ON) Buck switch ITEST = 200 mA 0.35 0.8 Ω

UVLOGD Gate drive UVLO VBST - VSW Increasing 3 4.3 5 V

UVLOGD Hysteresis 440 mV

OFF TIMER

tOFF Minimum OFF-time 265 ns

ON TIMER

tON - 1 ON-time VIN = 10 V, RON = 200 kΩ2.1 2.75 3.4 µs

tON - 2 ON-time VIN = 75 V, RON = 200 kΩ290 390 490 ns

0 8 20 40 60 80

VIN (V)

4.0

3.0

2.0

1.0

RON/SD PIN VOLTAGE (V)

RON = 50k

301k

511k

115k

0 8 20 40 60 80

VIN (V)

IIN (PA)

100

200

300

400

500

600

700

800

FB = 3V

RON/SD = 0V

8.0

7.0

6.0

5.0

4.0

3.0

2.0

1.0

ICC INPUT CURRENT(mA)

78 9 10 11 12 13

EXTERNALLY APPLIED VCC (V)

FS = 200 kHz

FS = 550 kHz

FS = 100 kHz

300k

0 8 20 40 60 80

VIN (V)

100k

RON = 500k

ON-TIME (Ps)

6.5 7.0 7.5 8.0 8.5 9.0 9.5

VIN (V)

VCC (V)

5.0

5.5

6.0

6.5

7.0

7.5

Load Current = 300 mA

ICC = 0 mA

FS = 200 kHz

FS = 620 kHz

FS = 100 kHz

0 2 4 6 8 10

VCC (V)

ICC (mA)

VIN = 48V

VIN = 8V

VIN = 9V

VCC Externally Loaded

FS = 100 kHz

LM5010

www.ti.com

SNVS307G –SEPTEMBER 2004–REVISED APRIL 2016

Product Folder Links: LM5010

6.7 Typical Characteristics

at TA= 25°C (unless otherwise noted)

Figure 1. VCC vs VIN Figure 2. VCC vs ICC

Figure 3. ICC vs Externally Applied VCC Figure 4. ON-Time vs VIN and RON

Figure 5. Voltage at RON/SD Pin Figure 6. IIN vs VIN

UVLO

VIN

SW Pin

Inductor

Current

SS Pin

VOUT

2.5V

7.0V

VCC

t1 t2

LM5010

SNVS307G –SEPTEMBER 2004–REVISED APRIL 2016

www.ti.com

Product Folder Links: LM5010

Typical Characteristics (continued)

at TA= 25°C (unless otherwise noted)

Figure 7. Start-Up Sequence

VCC

RTN

DRIVER

BST

2.5V

62.5 mV

SS L1

LM5010

7V START-UP

REGULATOR

RSENSE

REGULATION

COMPARATOR

LEVEL

SHIFT

CURRENT LIMIT

COMPARATOR

ON TIMER

START

RON

LOGIC

Driver

Gate Drive

UVLO

COMPLETE

START

265 ns

OFF TIMER

2.9V

OVER-VOLTAGE

COMPARATOR

GND

11.5 PA

COMPLETE

50 m:

RON/SD

VCC

UVLO Thermal

Shutdown

0.7V

INPUT

VOUT2

VOUT1

VIN

ISEN

SGND

RCL

VIN

RON

LM5010

www.ti.com

SNVS307G –SEPTEMBER 2004–REVISED APRIL 2016

Product Folder Links: LM5010

7 Detailed Description

7.1 Overview

The LM5010 step-down switching regulator features all the functions needed to implement a low-cost, efficient,

buck bias power converter. This high-voltage regulator contains a 75-V N-channel buck switch, is easy to

implement, and is provided in HTSSOP and thermally-enhanced, WSON packages. The regulator is based on a

control scheme using an ON-time inversely proportional to VIN. The control scheme requires no loop

compensation. The functional block diagram of the LM5010 is shown in the Functional Block Diagram.

The LM5010 can be applied in numerous applications to efficiently regulate down higher voltages. This regulator

is well-suited for 48-V telecom and 42-V automotive power bus ranges. Additional features include: thermal

shutdown, VCC undervoltage lockout, gate drive undervoltage lockout, maximum duty cycle limit timer, and the

valley current limit functionality.

7.2 Functional Block Diagram

Pin numbers are for the WSON (10) package

7.3 Feature Description

The LM5010 step-down switching regulator features all the functions needed to implement a low-cost, efficient

buck bias power converter capable of supplying in excess of 1 A to the load. This high voltage regulator contains

an N-Channel buck switch, is easy to implement, and is available in the thermally enhanced 10-pin WSON and

14-pin HTSSOP packages. The regulator’s operation is based on a constant ON-time control scheme, where the

ON-time varies inversely with VIN. This feature results in the operating frequency remaining relatively constant

with load and input voltage variations. The switching frequency can range from 100 kHz to > 1 MHz. The

hysteretic control requires no loop compensation, resulting in very fast load transient response. The valley

current limit detection circuit, internally set at 1.25 A, holds the buck switch off until the high current level

subsides. The LM5010 can be applied in numerous applications to efficiently regulate down higher voltages. This

regulator is well suited for 48-V telecom applications, as well as the new 42-V automotive power bus.

Implemented as a point-of-load regulator following a highly-efficient intermediate bus converter can result in high

overall system efficiency. Features include: Thermal shutdown, VCC undervoltage lockout, gate drive

undervoltage lockout, and maximum duty cycle limit.

FS = VOUT2 x L1 x 1.4 x 1020

RL x (RON)2

DC = tON

tON + tOFF

VOUT

VIN

FS = VOUT

1.18 x 10-10 x RON

LM5010

SNVS307G –SEPTEMBER 2004–REVISED APRIL 2016

www.ti.com

Product Folder Links: LM5010

Feature Description (continued)

7.3.1 Control Circuit Overview

The LM5010 buck DC-DC regulator employs a control scheme based on a comparator and a one-shot ON timer,

with the output voltage feedback (FB) compared to an internal reference (2.5 V). If the FB voltage is below the

reference the buck switch is turned on for a time period determined by the input voltage and a programming

resistor (RON). Following the ON-time the switch remains off for 265 ns, or until the FB voltage falls below the

reference, whichever is longer. The buck switch then turns on for another ON-time period. Typically when the

load current increases suddenly, the OFF-times are temporarily at the minimum of 265 ns. Once regulation is

established, the OFF-time resumes its normal value. The output voltage is set by two external resistors (R1, R2).

The regulated output voltage is calculated with Equation 1.

VOUT = 2.5 V × (R1 + R2) / R2 (1)

Output voltage regulation is based on ripple voltage at the feedback input, requiring a minimum amount of ESR

for the output capacitor C2. The LM5010 requires a minimum of 25-mV of ripple voltage at the FB pin. In cases

where the capacitor’s ESR is insufficient, additional series resistance may be required (R3 in Functional Block

Diagram).

When in regulation, the LM5010 operates in continuous conduction mode at heavy load currents and

discontinuous conduction mode at light load currents. In continuous conduction mode current always flows

through the inductor, never reaching zero during the OFF-time. In this mode the operating frequency remains

relatively constant with load and line variations. The minimum load current for continuous conduction mode is

one-half the inductor’s ripple current amplitude. Calculate the approximate operating frequency with Equation 2.

(2)

The buck switch duty cycle is approximately equal to Equation 3.

(3)

At low load current, the circuit operates in discontinuous conduction mode, during which the inductor current

ramps up from zero to a peak during the ON-time, then ramps back to zero before the end of the OFF-time. The

next ON-time period starts when the voltage at FB falls below the reference until then the inductor current

remains zero, and the load current is supplied by the output capacitor (C2). In this mode the operating frequency

is lower than in continuous conduction mode, and varies with load current. Conversion efficiency is maintained at

light loads because the switching losses reduce with the reduction in load and frequency. Calculate the

approximate discontinuous operating frequency with Equation 4.

where

• RL= the load resistance (4)

For applications where lower output voltage ripple is required, the output can be taken directly from a low ESR

output capacitor as shown in Figure 8. However, R3 slightly degrades the load regulation.

BST

VCC

LM5010

VOUT2

VOUT1

SGND

ISEN

LM5010 R1

VOUT2

LM5010

www.ti.com

SNVS307G –SEPTEMBER 2004–REVISED APRIL 2016

Product Folder Links: LM5010

Feature Description (continued)

Figure 8. Low Ripple Output Configuration

7.3.2 Start-Up Regulator (VCC)

The start-up regulator is integral to the LM5010. The input pin (VIN) can be connected directly to line voltages up

to 75 V. The VCC output is regulated at 7 V, ±6%, and is current-limited to 10 mA. Upon power up the regulator

sources current into the external capacitor at VCC (C3). With a 0.1-µF capacitor at VCC, approximately 58 µs are

required for the VCC voltage to reach the undervoltage lockout threshold (UVLO) of 5.8 V (t1 in Figure 7), at

which time the buck switch is enabled, and the soft-start pin is released to allow the soft-start capacitor (C6) to

charge up. VOUT then increases to its regulated value as the soft-start voltage increases (t2 in Figure 7).

The minimum input operating voltage is determined by the regulator’s dropout voltage, the VCC UVLO falling

threshold (≊5.65 V), and the frequency. When VCC falls below the falling threshold the VCC UVLO activates to

shut off the buck switch and ground the soft-start pin. If VCC is externally loaded, the minimum input voltage

increases since the output impedance at VCC is ≊140 Ωat low VIN. See Figure 1 and Figure 2. In applications

involving a high value for VIN where power dissipation in the start-up regulator is a concern, an auxiliary voltage

can be diode connected to the VCC pin (Figure 9). Setting the auxiliary voltage to between 7.5 V and 14 V shuts

off the internal regulator, reducing internal power dissipation. Figure 3 shows the current required into the VCC

pin. A diode connects VCC to VIN internally.

Figure 9. Self Biased Configuration

7.3.3 Regulation Comparator

The feedback voltage at FB is compared to the voltage at the soft-start pin (2.5 V, ±2%). In normal operation (the

output voltage is regulated) an ON-time period is initiated when the voltage at FB falls below 2.5 V. The buck

switch stays on for the ON-time causing the FB voltage to rise above 2.5 V. After the ON-time period the buck

switch stays off until the FB voltage falls below 2.5 V. Bias current at the FB pin is less than 5 nA over

temperature.

'I = (VIN - VOUT) x tON

tON = 1.18 x 10-10 x (RON + 1.4k)

VIN - 1.4V + 67 ns

LM5010

SNVS307G –SEPTEMBER 2004–REVISED APRIL 2016

www.ti.com

Product Folder Links: LM5010

Feature Description (continued)

7.3.4 Overvoltage Comparator

The feedback voltage at FB is compared to an internal 2.9-V reference. If the voltage at FB rises above 2.9 V,

the ON-time is immediately terminated. This condition can occur if the input voltage or the output load changes

suddenly. The buck switch will not turn on again until the voltage at FB falls below 2.5 V.

7.3.5 ON-Time Control

The ON-time of the internal switch (see Figure 4) is determined by the RON resistor and the input voltage (VIN),

calculated with Equation 5.

(5)

The inverse relationship of tON vs VIN results in a nearly constant frequency as VIN is varied. If the application

requires a high frequency, the minimum value for tON, and consequently RON, is limited by the OFF-time (265 ns,

±15%) which limits the maximum duty cycle at minimum VIN. The tolerance for Equation 5 is ±25%. Frequencies

in excess of 1 MHz are possible with the LM5010.

7.3.6 Current Limit

Current limit detection occurs during the OFF-time by monitoring the recirculating current through the free-

wheeling diode (D1). The detection threshold is 1.25 A, ±0.25 A. Referring to Functional Block Diagram, when

the buck switch is off the inductor current flows through the load, into SGND, through the sense resistor, out of

ISEN and through D1. If that current exceeds the threshold the current limit comparator output switches to delay

the start of the next ON-time period. The next ON-time starts when the current out of ISEN is below the threshold

and the voltage at FB is below 2.5 V. If the overload condition persists causing the inductor current to exceed the

threshold during each ON-time, that is detected at the beginning of each OFF-time. The operating frequency is

lower due to longer-than-normal OFF-times.

Figure 10 illustrates the inductor current waveform. During normal operation the load current is IO, the average of

the ripple waveform. When the load resistance decreases the current ratchets up until the lower peak attempts to

exceed the threshold. During the Current Limited portion of Figure 10, the current ramps down to the threshold

during each OFF-time, initiating the next ON-time (assuming the voltage at FB is < 2.5 V). During each ON-time

the current ramps up an amount equal to Equation 6.

(6)

During this time the LM5010 is in a constant current mode, with an average load current (IOCL) equal to the

threshold + ΔI / 2.

The valley current limit technique allows the load current to exceed the current limit threshold as long as the

lower peak of the inductor current is less than the threshold.

Threshold

IPK

IOCL

Inductor Current

Load Current

Increases

Normal Operation Current Limited

LM5010

www.ti.com

SNVS307G –SEPTEMBER 2004–REVISED APRIL 2016

Product Folder Links: LM5010

Feature Description (continued)

Figure 10. Inductor Current, Current Limit Operation

The current limit threshold can be increased by connecting an external resistor (RCL) between SGND and ISEN. The

external resistor typically is less than 1 Ω, and its calculation is explained in Application and Implementation.

The peak current out of SW and ISEN must not exceed 3.5 A. The average current out of SW must be less than

3 A, and the average current out of ISEN must be less than 2 A.

7.3.7 Soft Start

The soft-start feature allows the converter to gradually reach a steady-state operating point, thereby reducing

start-up stresses and current surges. Upon turnon, after VCC reaches the undervoltage threshold (t1 in Figure 7),

an internal 11.5-µA current source charges the external capacitor at the soft-start pin to 2.5 V (t2 in Figure 7).

The ramping voltage at SS (and at the non-inverting input of the regulation comparator) ramps up the output

voltage in a controlled manner. This feature keeps the load current from going to current limit during start-up,

thereby reducing inrush currents.

An internal switch grounds the soft-start pin if VCC is below the undervoltage lockout threshold, if a thermal

shutdown occurs, or if the circuit is shutdown using the RON/SD pin.

7.3.8 N-Channel Buck Switch and Driver

The LM5010 integrates an N-Channel buck switch and associated floating high voltage gate driver. The peak

current through the buck switch must not be allowed to exceed 3.5 A, and the average current must be less than

3 A. The gate driver circuit is powered by the external bootstrap capacitor between BST and SW (C4). During

each OFF-time, the SW pin is at approximately –1 V, and C4 is recharged from VCC through the internal high

voltage diode. The minimum OFF-time of 265 ns ensures a minimum time each cycle to recharge the bootstrap

capacitor. TI recommends a 0.022-µF ceramic capacitor for C4.

7.3.9 Thermal Shutdown

The LM5010 should be operated so the junction temperature does not exceed 125°C. If the junction temperature

increases above that, an internal Thermal Shutdown circuit activates (typically) at 175°C, taking the controller to

a low-power reset state by disabling the buck switch and the ON timer, and grounding the soft-start pin. This

feature helps prevent catastrophic failures from accidental device overheating. When the junction temperature

reduces below 155°C (typical hysteresis = 20°C), the softstart pin is released and normal operation resumes.

VIN

STOP

RON/SD

RON

Input

Voltage

LM5010

RUN

LM5010

SNVS307G –SEPTEMBER 2004–REVISED APRIL 2016

www.ti.com

Product Folder Links: LM5010

7.4 Device Functional Modes

7.4.1 Shutdown

The LM5010 can be remotely shut down by taking the RON/SD pin below 0.65 V. See Figure 11. In this mode the

soft-start pin is internally grounded, the ON timer is disabled, and the input current at VIN is reduced (Figure 6).

Releasing the RON/SD pin allows normal operation to resume. When the switch is open, the nominal voltage at

RON/SD is shown in Figure 5.

Figure 11. Shutdown Implementation

SGND

VIN

BST

LM5010

SHUTDOWN

VCC

RON / SD

15 - 75V

Input

137k

2.2 PF

RON

1.0k

3.0k R3

2.8

GND

15 PF

VOUT

10V

100 PH

0.1 PF

0.022 PF

0.1 PF

0.022 PF

RTN

ISEN

LM5010

www.ti.com

SNVS307G –SEPTEMBER 2004–REVISED APRIL 2016

Product Folder Links: LM5010

8 Application and Implementation

NOTE

Information in the following applications sections is not part of the TI component

specification, and TI does not warrant its accuracy or completeness. TI’s customers are

responsible for determining suitability of components for their purposes. Customers should

validate and test their design implementation to confirm system functionality.

8.1 Application Information

The LM5010 is a non-synchronous buck regulator converter designed to operate over a wide input voltage and

output current range. Spreadsheet-based calculator tools, available on the TI product website at Quick-Start

Calculator, can be used to design a single output non-synchronous buck converter.

Alternatively, online WEBENCH® software is available to create a complete buck design and generate the bill of

materials, estimated efficiency, solution size, and cost of the complete solution.

8.2 Typical Application

The final circuit is shown in Figure 12, and its performance is shown from Figure 14 to Figure 17.

Figure 12. LM5010 Example Circuit

8.2.1 Design Requirements

Table 1 lists the operating parameters for Figure 12.

Table 1. Design Parameters

PARAMETER EXAMPLE VALUE

Input voltage 15 V to 75 V

Output voltage 10 V

Load current 150 mA to 1 A

Soft-start time 5 ms

8.2.2 Detailed Design Procedure

The procedure for calculating the external components is illustrated with a design example. Configure the circuit

in Figure 12 according to the components listed in Table 2.

L1 Current

0 mA

IOR

1/Fs

IPK+

IPK-

RON = 10V

1.18 x 10-10 x 625 kHz= 136 k:

LM5010

SNVS307G –SEPTEMBER 2004–REVISED APRIL 2016

www.ti.com

Product Folder Links: LM5010

Table 2. List of Components for LM5010 Example Circuit

COMPONENT DESCRIPTION VALUE

C1 Ceramic Capacitor 2.2 µF, 100 V

C2 Ceramic Capacitor 15 µF, 25 V

C3 Ceramic Capacitor 0.1 µF, 16 V

C4, C6 Ceramic Capacitor 0.022 µF, 16 V

C5 Ceramic Capacitor 0.1 µF, 100 V

D1 Ultra-fast diode 100 V, 2 A

L1 Inductor 100 µH

R1 Resistor 3 kΩ

R2 Resistor 1 kΩ

R3 Resistor 2.8 Ω

RON Resistor 137 kΩ

U1 Switching regulator —

8.2.2.1 Component Selection

8.2.2.1.1 R1 and R2

Calculate the ratio of these resistors with Equation 7.

R1 / R2 = (VOUT / 2.5 V) - 1 (7)

R1 and R2 calculates to 3. The resistors should be chosen from standard value resistors in the range of 1 kΩto

10 kΩ. Values of 3 kΩfor R1, and 1 kΩfor R2 are used.

8.2.2.1.2 RON, FS

RON sets the ON-time, and can be chosen using Equation 2 to set a nominal frequency, or from Equation 5 if the

ON-time at a particular VIN is important. A higher frequency generally means a smaller inductor and capacitors

(value, size and cost), but higher switching losses. A lower frequency means a higher efficiency, but with larger

components. If PC board space is tight, a higher frequency is better. The resulting ON-time and frequency have

a ±25% tolerance, rearranging Equation 2 to Equation 8.

(8)

The next larger standard value (137 kΩ) is chosen for RON, yielding a nominal frequency of 618 kHz.

8.2.2.1.3 L1

The inductor value is determined based on the load current, ripple current, and the minimum and maximum input

voltage (VIN(min), VIN(max)). See Figure 13.

Figure 13. Inductor Current

To keep the circuit in continuous conduction mode, the maximum allowed ripple current is twice the minimum

load current, or 300 mAP-P. Using this value of ripple current, the inductor (L1) is calculated using Equation 9 and

Equation 10.

ESR(min) = R2 x IOR(min)

25 mV x (R1 + R2) = 2.8:

IOR(min) = L1MAX x FS(max) x VIN(min)

VOUT1 x (VIN(min) - VOUT1)

120 PH x 772 kHz x 15V

10V x (15V - 10V) = 36 mA

IOR(max) = 80 PH x 463 kHz x 75V

10V x (75V - 10V) = 234 mAp-p

IOR(max) = L1MIN x FS(min) x VIN(max)

VOUT1 x (VIN(max) - VOUT1)

L1 = 0.30A x 463 kHz x 75V

10V x (75V - 10V) = 63 PH

L1 = IOR x FS(min) x VIN(max)

VOUT1 x (VIN(max) - VOUT1)

LM5010

www.ti.com

SNVS307G –SEPTEMBER 2004–REVISED APRIL 2016

Product Folder Links: LM5010

where

• FS(min) is the minimum frequency (FS- 25%) (9)

(10)

Equation 10 provides the minimum value for inductor L1. When selecting an inductor, use a higher standard

value (100 uH). L1 must be rated for the peak current (IPK+) to prevent saturation. The peak current occurs at

maximum load current with maximum ripple. The maximum ripple is calculated by rearranging Equation 9 using

VIN(max), FS(min), and the minimum inductor value, based on the manufacturer’s tolerance. Assume for

Equation 11,Equation 12, and Equation 13 that the inductor’s tolerance is ±20%.

(11)

(12)

IPK+ = 1 A + 0.234 A / 2 = 1.117 A (13)

8.2.2.1.4 RCL

Since it is obvious that the lower peak of the inductor current waveform does not exceed 1 A at maximum load

current (see Figure 13), it is not necessary to increase the current limit threshold. Therefore RCL is not needed for

this exercise. For applications where the lower peak exceeds 1 A, see Increasing The Current Limit Threshold.

8.2.2.1.5 C2 and R3

Since the LM5010 requires a minimum of 25 mVP-P of ripple at the FB pin for proper operation, the required ripple

at VOUT1 is increased by R1 and R2. This necessary ripple is created by the inductor ripple current acting on C2’s

ESR + R3. First, determine the minimum ripple current with Equation 14.

(14)

The minimum ESR for C2 is then equal to Equation 15.

(15)

If the capacitor used for C2 does not have sufficient ESR, R3 is added in series as shown in Figure 12. C2

should generally be no smaller than 3.3 µF, although that is dependent on the frequency and the allowable ripple

amplitude at VOUT1. Experimentation is usually necessary to determine the minimum value for C2, as the nature

of the load may require a larger value. A load which creates significant transients requires a larger value for C2

than a non-varying load.

C1 = 'V

IO x tON = 1.57 PF

1.0A x 1.57 Ps

tON(max) = 15V - 1.4V

1.18 x 10-10 x (137k + 1.4k) x 1.25 + 67 ns = 1.57 Ps

LM5010

SNVS307G –SEPTEMBER 2004–REVISED APRIL 2016

www.ti.com

Product Folder Links: LM5010

8.2.2.1.6 D1

The important parameters are reverse recovery time and forward voltage drop. The reverse recovery time

determines how long the current surge lasts each time the buck switch is turned on. The forward voltage drop is

significant in the event the output is short-circuited as it is mainly this diode’s voltage (plus the voltage across the

current limit sense resistor) which forces the inductor current to decrease during the OFF-time. For this reason, a

higher voltage is better, although that affects efficiency. A reverse recovery time of ≊30 ns, and a forward voltage

drop of ≊0.75 V are preferred. The reverse leakage specification is important as that can significantly affect

efficiency. Other types of diodes may have a lower forward voltage drop, but may have longer recovery times, or

greater reverse leakage. D1 should be rated for the maximum VIN, and for the peak current when in current limit

(IPK in Figure 11) which is equal to Equation 16.

IPK = 1.5 A + IOR(max) = 1.734 A

where

• 1.5 A is the maximum guaranteed current limit threshold

• the maximum ripple current was previously calculated as 234 mAP-P (16)

This calculation is only valid when RCL is not required.

8.2.2.1.7 C1

Assuming the voltage supply feeding VIN has a source impedance greater than zero, this capacitor limits the

ripple voltage at VIN while supplying most of the switch current during the ON-time. At maximum load current,

when the buck switch turns on, the current into VIN increases to the lower peak of the output current waveform,

ramps up to the peak value, then drops to zero at turnoff. The average current into VIN during this ON-time is the

load current. For a worst case calculation, C1 must supply this average load current during the maximum ON-

time. The maximum ON-time is calculated using Equation 5, with a 25% tolerance added in Equation 17.

(17)

C1 is calculated with Equation 18.

where

• IOis the load current

•ΔV is the allowable ripple voltage at VIN (1 V for this example) (18)

TI recommends quality ceramic capacitors with a low ESR for C1. To allow for capacitor tolerances and voltage

effects, use a 2.2-µF capacitor.

8.2.2.1.8 C3

The capacitor at the VCC pin provides not only noise filtering and stability, but also prevents false triggering of

the VCC UVLO at the buck switch ON and OFF transitions. For this reason, C3 should be no smaller than 0.1 µF,

and should be a good quality, low ESR, ceramic capacitor. This capacitor also determines the initial start-up

delay (t1 in Figure 7).

8.2.2.1.9 C4

TI recommends a value of 0.022 µF for C4. TI recommends a high-quality ceramic capacitor with low ESR,

because C4 supplies the surge current to charge the buck switch gate at turnon. A low ESR also ensures a

complete recharge during each OFF-time.

8.2.2.1.10 C5

This capacitor suppresses transients and ringing due to long lead inductance at VIN. TI recommends a low ESR,

0.1-µF ceramic chip capacitor, placed physically close to the LM5010.

IPK+(CL) = RCL

1.5A x (150 m: + RCL)+ IOR(MAX)

IPK+ = IO(max) + 2

IOR(max)

IAVE = (RCL + 0.11:x VIN(max)

IO(max) x RCL x (VIN(max) - VOUT)

RCL = 1.0A x 0.11:

IPK- - 1.0A

IPK- = IO(max) - 2

IOR(min)

tSS = 11.5 PA

C6 x 2.5V

LM5010

www.ti.com

SNVS307G –SEPTEMBER 2004–REVISED APRIL 2016

Product Folder Links: LM5010

8.2.2.1.11 C6

The capacitor at the SS pin determines the soft-start time (that is the time for the reference voltage at the

regulation comparator and the output voltage), to reach their final value. Determine the time with Equation 19.

(19)

For a 5-ms soft-start time, C6 calculates to 0.022 µF.

8.2.2.2 Increasing The Current Limit Threshold

The current limit threshold is nominally 1.25 A, with a minimum guaranteed value of 1 A. If, at maximum load

current, the lower peak of the inductor current (IPK– in Figure 13) exceeds 1 A, resistor RCL must be added

between SGND and ISEN to increase the current limit threshold to be equal or exceed that lower peak current. This

resistor diverts some of the recirculating current from the internal sense resistor so that a higher current level is

needed to switch the internal current limit comparator. Calculate IPK– with Equation 20.

where

• IO(max) is the maximum load current

• IOR(min) is the minimum ripple current calculated using Equation 14 (20)

RCL is calculated with Equation 21.

where

• 0.11 Ωis the minimum value of the internal resistance from SGND to ISEN (21)

The next smaller standard value resistor should be used for RCL. With the addition of RCL it is necessary to check

the average and peak current values to ensure they do not exceed the LM5010 limits. At maximum load current

the average current through the internal sense resistor is calculated with Equation 22.

(22)

If IAVE is less than 2 A, no changes are necessary. If it exceeds 2 A, RCL must be reduced. The upper peak of the

inductor current (IPK+), at maximum load current, is calculated using Equation 23.

where

• IOR(max) is calculated using Equation 11 (23)

If IPK+ exceeds 3.5 A , the inductor value must be increased to reduce the ripple amplitude. This necessitates

recalculation of IOR(min), IPK–, and RCL.

When the circuit is in current limit, the upper peak current out of the SW pin is calculated with Equation 24.

(24)

The inductor L1 and diode D1 must be rated for this current.

ff SW FB2 FB1

3L1,min

CF (R IIR )

25 mV

u '

3REF L1,min

25 mV V

RV I

IN,min

IN,min O ON(@V )

A A (V V ) T

R C 25mV

 u

GND

To FB

COUT

RFB2

RFB1

VOUT

GND

To FB

COUT

RFB2

RFB1

VOUT

Cff

COUT

VOUT

GND

To FB

RFB2

RFB1

LM5010

SNVS307G –SEPTEMBER 2004–REVISED APRIL 2016

www.ti.com

Product Folder Links: LM5010

8.2.2.3 Ripple Configuration

The LM5010 uses a constant-ON-time (COT) control scheme where the ON-time is terminated by a one-shot and

the OFF-time is terminated by the feedback voltage (VFB) falling below the reference voltage. Therefore, for

stable operation, the feedback voltage must decrease monotonically in phase with the inductor current during the

OFF-time. Furthermore, this change in feedback voltage (VFB) during OFF-time must be large enough to

dominate any noise present at the feedback node.

Table 3 presents three different methods for generating appropriate voltage ripple at the feedback node. Type 1

and type 2 ripple circuits couple the ripple from the output of the converter to the feedback node (FB). The output

voltage ripple has two components:

1. Capacitive ripple caused by the inductor current ripple charging or discharging the output capacitor.

2. Resistive ripple caused by the inductor current ripple flowing through the ESR of the output capacitor and

R3.

Table 3. Ripple Configuration

TYPE 1 TYPE 2 TYPE 3

Lowest cost Reduced ripple Minimum ripple

(25) (26) (27)

The capacitive ripple is out of phase with the inductor current. As a result, the capacitive ripple does not

decrease monotonically during the OFF-time. The resistive ripple is in phase with the inductor current and

decreases monotonically during the OFF-time. The resistive ripple must exceed the capacitive ripple at output

(VOUT) for stable operation. If this condition is not satisfied, then unstable switching behavior is observed in COT

converters with multiple ON-time bursts in close succession followed by a long OFF-time.

The type 3 ripple method uses a ripple injection circuit with RA, CA, and the switch node (SW) voltage to generate

a triangular ramp. This triangular ramp is then AC-coupled into the feedback node (FB) using the capacitor CB.

This circuit is suited for applications where low output voltage ripple is imperative because this circuit does not

use the output voltage ripple. See AN-1481 Controlling Output Ripple and Achieving ESR Independence in

Constant ON-Time (COT) Regulator Designs, (SNVA166) for more details on each ripple generation method.

020 40 60 80

VIN (V)

100

150

200

250

300

350

OUTPUT RIPPLE (mVp-p)

FREQUENCY (kHz)

020 40 60 80

VIN (V)

700

600

500

400

300

0 200 400 600 800 _1000

100

EFFICIENCY (%)

LOAD CURRENT (mA)

VIN = 15V 24V

48V

75V

IOUT = 300mA

VIN (V)

0 20 40 60 80

EFFICIENCY (%)

100

LM5010

www.ti.com

SNVS307G –SEPTEMBER 2004–REVISED APRIL 2016

Product Folder Links: LM5010

8.2.3 Application Curves

Figure 14. Efficiency vs VIN Figure 15. Efficiency vs Load Current and VIN

Figure 16. Output Voltage Ripple vs VIN Figure 17. Frequency vs VIN

8.3 Do's and Don'ts

A minimum load current of 1 mA is required to maintain proper operation. If the load current falls below that level,

the bootstrap capacitor can discharge during the long OFF-time and the circuit either shuts down or cycles ON

and OFF at a low frequency. If the load current is expected to drop below 1 mA in the application, choose the

feedback resistors to be low enough in value to provide the minimum required current at nominal VOUT.

GND

RFB1

VLINE

CBST

Cbyp

VOUT

LIND

RFB2

RON

COUT

CIN

Via to Ground Plane

CVCC

BST

ISEN

SGND

RON

VCC

GND

D1 Exp Thermal

Pad

RTN

RON

VCC

VIN

SGND

ISEN

BST

CSS

LM5010

SNVS307G –SEPTEMBER 2004–REVISED APRIL 2016

www.ti.com

Product Folder Links: LM5010

9 Power Supply Recommendations

The LM5010 is designed to operate with an input power supply capable of supplying a voltage range from 8 V to

75 V. The input power supply must be well-regulated and capable of supplying sufficient current to the regulator

during peak load operation. Also, like in all applications, the power-supply source impedance must be small

compared to the module input impedance to maintain the stability of the converter.

10 Layout

10.1 Layout Guidelines

The LM5010 regulation, overvoltage, and current limit comparators are very fast, and respond to short duration

noise pulses. Therefore, layout considerations are critical for optimum performance. The layout must be as neat

and compact as possible, and all the components must be as close as possible to their associated pins. The

current loop formed by D1, L1 (LIND), C2 (COUT), and the SGND and ISEN pins should be as small as possible. The

ground connection from C2 (COUT) to C1 (CIN) should be as short and direct as possible. If it is expected that the

internal dissipation of the LM5010 will produce high junction temperatures during normal operation, good use of

the PC board’s ground plane can help considerably to dissipate heat. The exposed pad on the IC package

bottom can be soldered to a ground plane, and that plane should both extend from beneath the IC, and be

connected to exposed ground plane on the board’s other side using as many vias as possible. The exposed pad

is internally connected to the IC substrate.

The use of wide PC board traces at the pins, where possible, can help conduct heat away from the IC. The four

no connect pins on the HTSSOP package are not electrically connected to any part of the IC, and may be

connected to ground plane to help dissipate heat from the package. Judicious positioning of the PC board within

the end product, along with the use of any available air flow (forced or natural convection) can help reduce the

junction temperature.

10.2 Layout Example

Figure 18. LM5010 Buck Layout Example With the WSON Package

LM5010

www.ti.com

SNVS307G –SEPTEMBER 2004–REVISED APRIL 2016

Product Folder Links: LM5010

11 Device and Documentation Support

11.1 Community Resources

The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective

contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of

Use.

TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration

among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help

solve problems with fellow engineers.

Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and

contact information for technical support.

11.2 Trademarks

E2E is a trademark of Texas Instruments.

All other trademarks are the property of their respective owners.

11.3 Electrostatic Discharge Caution

These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam

during storage or handling to prevent electrostatic damage to the MOS gates.

11.4 Glossary

SLYZ022 —TI Glossary.

This glossary lists and explains terms, acronyms, and definitions.

12 Mechanical, Packaging, and Orderable Information

The following pages include mechanical, packaging, and orderable information. This information is the most

current data available for the designated devices. This data is subject to change without notice and revision of

this document. For browser-based versions of this data sheet, refer to the left-hand navigation.

PACKAGE OPTION ADDENDUM

www.ti.com 11-Jan-2021

Addendum-Page 1

PACKAGING INFORMATION

Orderable Device Status

(1)

Package Type Package

Drawing Pins Package

Qty Eco Plan

(2)

Lead finish/

Ball material

(6)

MSL Peak Temp

(3)

Op Temp (°C) Device Marking

(4/5)

Samples

LM5010MH NRND HTSSOP PWP 14 94 Non-RoHS

& Green Call TI Call TI -40 to 125 L5010

LM5010MH/NOPB ACTIVE HTSSOP PWP 14 94 RoHS & Green SN Level-1-260C-UNLIM -40 to 125 L5010

LM5010MHX/NOPB ACTIVE HTSSOP PWP 14 2500 RoHS & Green SN Level-1-260C-UNLIM -40 to 125 L5010

LM5010SD/NOPB ACTIVE WSON DPR 10 1000 RoHS & Green NIPDAU | SN Level-1-260C-UNLIM -40 to 125 L00057B

LM5010SDX/NOPB ACTIVE WSON DPR 10 4500 RoHS & Green NIPDAU | SN Level-1-260C-UNLIM -40 to 125 L00057B

(1) The marketing status values are defined as follows:

ACTIVE: Product device recommended for new designs.

LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.

NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.

PREVIEW: Device has been announced but is not in production. Samples may or may not be available.

OBSOLETE: TI has discontinued the production of the device.

(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance

do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may

reference these types of products as "Pb-Free".

RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.

Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based

flame retardants must also meet the <=1000ppm threshold requirement.

(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.

(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.

(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation

of the previous line and the two combined represent the entire Device Marking for that device.

(6) Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two

lines if the finish value exceeds the maximum column width.

PACKAGE OPTION ADDENDUM

www.ti.com 11-Jan-2021

Addendum-Page 2

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information

provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and

continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.

TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.

TAPE AND REEL INFORMATION

*All dimensions are nominal

Device Package

Type Package

Drawing Pins SPQ Reel

Diameter

(mm)

Reel

Width

W1 (mm)

(mm) B0

(mm) K0

(mm) P1

(mm) W

(mm) Pin1

Quadrant

LM5010MHX/NOPB HTSSOP PWP 14 2500 330.0 12.4 6.95 5.6 1.6 8.0 12.0 Q1

LM5010SD/NOPB WSON DPR 10 1000 178.0 12.4 4.3 4.3 1.3 8.0 12.0 Q1

LM5010SDX/NOPB WSON DPR 10 4500 330.0 12.4 4.3 4.3 1.3 8.0 12.0 Q1

PACKAGE MATERIALS INFORMATION

www.ti.com 23-Apr-2020

Pack Materials-Page 1

*All dimensions are nominal

Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)

LM5010MHX/NOPB HTSSOP PWP 14 2500 367.0 367.0 35.0

LM5010SD/NOPB WSON DPR 10 1000 210.0 185.0 35.0

LM5010SDX/NOPB WSON DPR 10 4500 367.0 367.0 35.0

PACKAGE MATERIALS INFORMATION

www.ti.com 23-Apr-2020

Pack Materials-Page 2

MECHANICAL DATA

PWP0014A

www.ti.com

MXA14A (Rev A)

www.ti.com

PACKAGE OUTLINE

10X 0.35

0.25

3 0.1

2.6 0.1

0.8

0.7

8X 0.8

10X 0.5

0.3

(0.1) TYP

3.2

0.05

0.00

B4.1

3.9 A

4.1

3.9

(0.2)

WSON - 0.8 mm max heightDPR0010A

PLASTIC SMALL OUTLINE - NO LEAD

4218856/B 01/2021

PIN 1 INDEX AREA

SEATING PLANE

0.08 C

PIN 1 ID 0.1 C A B

0.05 C

THERMAL PAD

EXPOSED

SEE ALTERNATIVE

LEAD DETAIL

NOTES:

1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing

per ASME Y14.5M.

2. This drawing is subject to change without notice.

3. The package thermal pad must be soldered to the printed circuit board for thermal and mechanical performance.

SCALE 3.000

20.000

FULL R

ALTERNATIVE LEAD

DETAIL

BOTTOM VIEW SIDE VIEW

www.ti.com

EXAMPLE BOARD LAYOUT

(R0.05) TYP

8X (0.8)

0.07 MIN

ALL AROUND

0.07 MAX

ALL AROUND

(2.6)

(3.8)

10X (0.3)

10X (0.6)

(3)

( 0.2) VIA

TYP

(1.25)

(1.05)

WSON - 0.8 mm max heightDPR0010A

PLASTIC SMALL OUTLINE - NO LEAD

4218856/B 01/2021

SYMM

LAND PATTERN EXAMPLE

EXPOSED METAL SHOWN

SCALE:15X

NOTES: (continued)

4. This package is designed to be soldered to a thermal pad on the board. For more information, see Texas Instruments literature

number SLUA271 (www.ti.com/lit/slua271).

SOLDER MASK

OPENING

SOLDER MASK

METAL UNDER

SOLDER MASK

DEFINED

EXPOSED

METAL

EDGE

SOLDER MASK

OPENING

SOLDER MASK DETAILS

NON SOLDER MASK

DEFINED

(PREFERRED)

EXPOSED

METAL

www.ti.com

EXAMPLE STENCIL DESIGN

10X (0.3)

10X (0.6)

8X (0.8)

(1.31)

4X (1.15)

(0.76)

(3.8)

(R0.05) TYP

(0.68)

WSON - 0.8 mm max heightDPR0010A

PLASTIC SMALL OUTLINE - NO LEAD

4218856/B 01/2021

NOTES: (continued)

5. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate

design recommendations.

SOLDER PASTE EXAMPLE

BASED ON 0.125 mm THICK STENCIL

EXPOSED PAD 11:

77% PRINTED SOLDER COVERAGE BY AREA

SCALE:20X

SYMM

METAL

TYP

IMPORTANT NOTICE AND DISCLAIMER

TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE

DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”

AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY

IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD

PARTY INTELLECTUAL PROPERTY RIGHTS.

These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate

TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable

standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you

permission to use these resources only for development of an application that uses the TI products described in the resource. Other

reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party

intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims, damages,

costs, losses, and liabilities arising out of your use of these resources.

TI’s products are provided subject to TI’s Terms of Sale (https:www.ti.com/legal/termsofsale.html) or other applicable terms available either

on ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s

applicable warranties or warranty disclaimers for TI products.IMPORTANT NOTICE

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265