LMC662
LMC662 CMOS Dual Operational Amplifier
Literature Number: SNOSC51B
LMC662
CMOS Dual Operational Amplifier
General Description
The LMC662 CMOS Dual operational amplifier is ideal for
operation from a single supply. It operates from +5V to +15V
and features rail-to-rail output swing in addition to an input
common-mode range that includes ground. Performance
limitations that have plagued CMOS amplifiers in the past
are not a problem with this design. Input V
OS
, drift, and
broadband noise as well as voltage gain into realistic loads
(2 kand 600) are all equal to or better than widely
accepted bipolar equivalents.
This chip is built with National’s advanced Double-Poly
Silicon-Gate CMOS process.
See the LMC660 datasheet for a Quad CMOS operational
amplifier with these same features.
Features
nRail-to-rail output swing
nSpecified for 2 kand 600loads
nHigh voltage gain: 126 dB
nLow input offset voltage: 3 mV
nLow offset voltage drift: 1.3 µV/˚C
nUltra low input bias current: 2 fA
nInput common-mode range includes V
nOperating range from +5V to +15V supply
nI
SS
= 400 µA/amplifier; independent of V+
nLow distortion: 0.01% at 10 kHz
nSlew rate: 1.1 V/µs
Applications
nHigh-impedance buffer or preamplifier
nPrecision current-to-voltage converter
nLong-term integrator
nSample-and-hold circuit
nPeak detector
nMedical instrumentation
nIndustrial controls
nAutomotive sensors
Connection Diagram
8-Pin DIP/SO
00976301
Typical Application
Low-Leakage Sample-and-Hold
00976315
Ordering Information
Package Temperature Range NSC
Drawing
Transport
Media
Industrial Commercial
8-Pin
Small Outline
LMC662AIM LMC662CM M08A Rail
LMC662AIMX LMC662CMX Tape and Reel
8-Pin
Molded DIP
LMC662AIN LMC662CN N08E Rail
April 2003
LMC662 CMOS Dual Operational Amplifier
© 2003 National Semiconductor Corporation DS009763 www.national.com
Absolute Maximum Ratings (Note 3)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Differential Input Voltage ±Supply Voltage
Supply Voltage (V
+
−V
) 16V
Output Short Circuit to V
+
(Note 12)
Output Short Circuit to V
(Note 1)
Lead Temperature
(Soldering, 10 sec.) 260˚C
Storage Temp. Range −65˚C to +150˚C
Voltage at Input/Output Pins (V
+
) +0.3V, (V
) −0.3V
Current at Output Pin ±18 mA
Current at Input Pin ±5mA
Current at Power Supply Pin 35 mA
Power Dissipation (Note 2)
Junction Temperature 150˚C
ESD Tolerance (Note 8) 1000V
Operating Ratings(Note 3)
Temperature Range
LMC662AI −40˚C T
J
+85˚C
LMC662C 0˚C T
J
+70˚C
Supply Voltage Range 4.75V to 15.5V
Power Dissipation (Note 10)
Thermal Resistance (θ
JA
) (Note 11)
8-Pin Molded DIP 101˚C/W
8-Pin SO 165˚C/W
DC Electrical Characteristics
Unless otherwise specified, all limits guaranteed for T
J
= 25˚C. Boldface limits apply at the temperature extremes. V
+
= 5V,
V
= 0V, V
CM
= 1.5V, V
O
= 2.5V and R
L
>1M unless otherwise specified.
Parameter Conditions Typ
(Note 4)
LMC662AI LMC662C Units
Limit Limit
(Note 4) (Note 4)
Input Offset Voltage 1 3 6 mV
3.3 6.3 max
Input Offset Voltage 1.3 µV/˚C
Average Drift
Input Bias Current 0.002 pA
42max
Input Offset Current 0.001 pA
21max
Input Resistance >1 Tera
Common Mode 0V V
CM
12.0V 83 70 63 dB
Rejection Ratio V
+
= 15V 68 62 min
Positive Power Supply 5V V
+
15V 83 70 63 dB
Rejection Ratio V
O
= 2.5V 68 62 min
Negative Power Supply 0V V
−10V 94 84 74 dB
Rejection Ratio 83 73 min
Input Common-Mode V
+
= 5V & 15V −0.4 −0.1 −0.1 V
Voltage Range For CMRR 50 dB 00max
V
+
1.9 V
+
2.3 V
+
2.3 V
V
+
2.5 V
+
2.4 min
Large Signal R
L
=2k(Note 5) 2000 440 300 V/mV
Voltage Gain Sourcing 400 200 min
Sinking 500 180 90 V/mV
120 80 min
R
L
= 600(Note 5) 1000 220 150 V/mV
Sourcing 200 100 min
Sinking 250 100 50 V/mV
60 40 min
LMC662
www.national.com 2
DC Electrical Characteristics (Continued)
Unless otherwise specified, all limits guaranteed for T
J
= 25˚C. Boldface limits apply at the temperature extremes. V
+
= 5V,
V
= 0V, V
CM
= 1.5V, V
O
= 2.5V and R
L
>1M unless otherwise specified.
Parameter Conditions Typ
(Note 4)
LMC662AI LMC662C Units
Limit Limit
(Note 4) (Note 4)
Output Swing V
+
= 5V 4.87 4.82 4.78 V
R
L
=2kto V
+
/2 4.79 4.76 min
0.10 0.15 0.19 V
0.17 0.21 max
V
+
= 5V 4.61 4.41 4.27 V
R
L
= 600to V
+
/2 4.31 4.21 min
0.30 0.50 0.63 V
0.56 0.69 max
V
+
= 15V 14.63 14.50 14.37 V
R
L
=2kto V
+
/2 14.44 14.32 min
0.26 0.35 0.44 V
0.40 0.48 max
V
+
= 15V 13.90 13.35 12.92 V
R
L
= 600to V
+
/2 13.15 12.76 min
0.79 1.16 1.45 V
1.32 1.58 max
Output Current Sourcing, V
O
=0V221613mA
V
+
=5V 14 11 min
Sinking, V
O
=5V211613mA
14 11 min
Output Current Sourcing, V
O
=0V402823mA
V
+
= 15V 25 21 min
Sinking, V
O
= 13V 39 28 23 mA
(Note 12) 24 20 min
Supply Current Both Amplifiers 0.75 1.3 1.6 mA
V
O
= 1.5V 1.5 1.8 max
AC Electrical Characteristics
Unless otherwise specified, all limits guaranteed for T
J
= 25˚C. Boldface limits apply at the temperature extremes. V
+
= 5V,
V
= 0V, V
CM
= 1.5V, V
O
= 2.5V and R
L
>1M unless otherwise specified.
Parameter Conditions Typ
(Note 4)
LMC662AI LMC662C Units
Limit Limit
(Note 4) (Note 4)
Slew Rate (Note 6) 1.1 0.8 0.8 V/µs
0.6 0.7 min
Gain-Bandwidth Product 1.4 MHz
Phase Margin 50 Deg
Gain Margin 17 dB
Amp-to-Amp Isolation (Note 7) 130 dB
Input-Referred Voltage Noise F = 1 kHz 22
Input-Referred Current Noise F = 1 kHz 0.0002
LMC662
www.national.com3
AC Electrical Characteristics (Continued)
Unless otherwise specified, all limits guaranteed for T
J
= 25˚C. Boldface limits apply at the temperature extremes. V
+
= 5V,
V
= 0V, V
CM
= 1.5V, V
O
= 2.5V and R
L
>1M unless otherwise specified.
Parameter Conditions Typ
(Note 4)
LMC662AI LMC662C Units
Limit Limit
(Note 4) (Note 4)
Total Harmonic Distortion F = 10 kHz, A
V
= −10
%R
L
=2k,V
O
=8V
PP
0.01
V
+
= 15V
Note 1: Applies to both single-supply and split-supply operation. Continuous short circuit operation at elevated ambient temperature and/or multiple Op Amp shorts
can result in exceeding the maximum allowed junction temperature of 150˚C. Output currents in excess of ±30 mA over long term may adversely affect reliability.
Note 2: The maximum power dissipation is a function of TJ(max),θJA, and TA. The maximum allowable power dissipation at any ambient temperature is PD=
(TJ(max)–TA)/θJA.
Note 3: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
intended to be functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The
guaranteed specifications apply only for the test conditions listed.
Note 4: Typical values represent the most likely parametric norm. Limits are guaranteed by testing or correlation.
Note 5: V+= 15V, VCM = 7.5V and RLconnected to 7.5V. For Sourcing tests, 7.5V VO11.5V. For Sinking tests, 2.5V VO7.5V.
Note 6: V+= 15V. Connected as Voltage Follower with 10V step input. Number specified is the slower of the positive and negative slew rates.
Note 7: Input referred. V+= 15V and RL=10kconnected to V+/2. Each amp excited in turn with 1 kHz to produce VO=13V
PP.
Note 8: Human body model, 1.5 kin series with 100 pF.
Note 9: A military RETS electrical test specification is available on request.
Note 10: For operating at elevated temperatures the device must be derated based on the thermal resistance θJA with PD=(T
J–TA)/θJA.
Note 11: All numbers apply for packages soldered directly into a PC board.
Note 12: Do not connect output to V+when V+is greater than 13V or reliability may be adversely affected.
LMC662
www.national.com 4
Typical Performance Characteristics V
S
=±7.5V, T
A
= 25˚C unless otherwise specified
Supply Current vs. Supply Voltage Offset Voltage
00976324 00976325
Input Bias Current Output Characteristics Current Sinking
00976326 00976327
Output Characteristics Current Sourcing Input Voltage Noise vs. Frequency
00976328 00976329
LMC662
www.national.com5
Typical Performance Characteristics V
S
=±7.5V, T
A
= 25˚C unless otherwise specified (Continued)
CMRR vs. Frequency Open-Loop Frequency Response
00976330 00976331
Frequency Response vs. Capacitive Load Non-Inverting Large Signal Pulse Response
00976332
00976333
Stability vs. Capacitive Load Stability vs. Capacitive Load
00976334
Note: Avoid resistive loads of less than 500, as they may cause instability.
00976335
Note: Avoid resistive loads of less than 500, as they may cause instability.
LMC662
www.national.com 6
Application Hints
AMPLIFIER TOPOLOGY
The topology chosen for the LMC662, shown in Figure 1,is
unconventional (compared to general-purpose op amps) in
that the traditional unity-gain buffer output stage is not used;
instead, the output is taken directly from the output of the
integrator, to allow rail-to-rail output swing. Since the buffer
traditionally delivers the power to the load, while maintaining
high op amp gain and stability, and must withstand shorts to
either rail, these tasks now fall to the integrator.
As a result of these demands, the integrator is a compound
affair with an embedded gain stage that is doubly fed forward
(via C
f
and C
ff
) by a dedicated unity-gain compensation
driver. In addition, the output portion of the integrator is a
push-pull configuration for delivering heavy loads. While
sinking current the whole amplifier path consists of three
gain stages with one stage fed forward, whereas while
sourcing the path contains four gain stages with two fed
forward.
The large signal voltage gain while sourcing is comparable
to traditional bipolar op amps, even with a 600load. The
gain while sinking is higher than most CMOS op amps, due
to the additional gain stage; however, under heavy load
(600) the gain will be reduced as indicated in the Electrical
Characteristics.
COMPENSATING INPUT CAPACITANCE
The high input resistance of the LMC662 op amps allows the
use of large feedback and source resistor values without
losing gain accuracy due to loading. However, the circuit will
be especially sensitive to its layout when these large-value
resistors are used.
Every amplifier has some capacitance between each input
and AC ground, and also some differential capacitance be-
tween the inputs. When the feedback network around an
amplifier is resistive, this input capacitance (along with any
additional capacitance due to circuit board traces, the
socket, etc.) and the feedback resistors create a pole in the
feedback path. In the following General Operational Amplifier
Circuit, Figure 2, the frequency of this pole is
where C
S
is the total capacitance at the inverting input,
including amplifier input capacitance and any stray capaci-
tance from the IC socket (if one is used), circuit board traces,
etc., and R
P
is the parallel combination of R
F
and R
IN
. This
formula, as well as all formulae derived below, apply to
inverting and non-inverting op-amp configurations.
When the feedback resistors are smaller than a few k, the
frequency of the feedback pole will be quite high, since C
S
is
generally less than 10 pF. If the frequency of the feedback
pole is much higher than the “ideal” closed-loop bandwidth
(the nominal closed-loop bandwidth in the absence of C
S
),
the pole will have a negligible effect on stability, as it will add
only a small amount of phase shift.
However, if the feedback pole is less than approximately 6 to
10 times the “ideal” −3 dB frequency, a feedback capacitor,
C
F
, should be connected between the output and the invert-
ing input of the op amp. This condition can also be stated in
terms of the amplifier’s low-frequency noise gain: To main-
tain stability, a feedback capacitor will probably be needed if
where
is the amplifier’s low-frequency noise gain and GBW is the
amplifier’s gain bandwidth product. An amplifier’s low-
frequency noise gain is represented by the formula
regardless of whether the amplifier is being used in an
inverting or non-inverting mode. Note that a feedback ca-
pacitor is more likely to be needed when the noise gain is low
and/or the feedback resistor is large.
If the above condition is met (indicating a feedback capacitor
will probably be needed), and the noise gain is large enough
that:
the following value of feedback capacitor is recommended:
If
the feedback capacitor should be:
00976304
FIGURE 1. LMC662 Circuit Topology (Each Amplifier)
LMC662
www.national.com7
Application Hints (Continued)
Note that these capacitor values are usually significantly
smaller than those given by the older, more conservative
formula:
Using the smaller capacitors will give much higher band-
width with little degradation of transient response. It may be
necessary in any of the above cases to use a somewhat
larger feedback capacitor to allow for unexpected stray ca-
pacitance, or to tolerate additional phase shifts in the loop, or
excessive capacitive load, or to decrease the noise or band-
width, or simply because the particular circuit implementa-
tion needs more feedback capacitance to be sufficiently
stable. For example, a printed circuit board’s stray capaci-
tance may be larger or smaller than the breadboard’s, so the
actual optimum value for C
F
may be different from the one
estimated using the breadboard. In most cases, the value of
C
F
should be checked on the actual circuit, starting with the
computed value.
CAPACITIVE LOAD TOLERANCE
Like many other op amps, the LMC662 may oscillate when
its applied load appears capacitive. The threshold of oscilla-
tion varies both with load and circuit gain. The configuration
most sensitive to oscillation is a unity-gain follower. See the
Typical Performance Characteristics.
The load capacitance interacts with the op amp’s output
resistance to create an additional pole. If this pole frequency
is sufficiently low, it will degrade the op amp’s phase margin
so that the amplifier is no longer stable at low gains. As
shown in Figure 3, the addition of a small resistor (50to
100) in series with the op amp’s output, and a capacitor (5
pF to 10 pF) from inverting input to output pins, returns the
phase margin to a safe value without interfering with lower-
frequency circuit operation. Thus, larger values of capaci-
tance can be tolerated without oscillation. Note that in all
cases, the output will ring heavily when the load capacitance
is near the threshold for oscillation.
Capacitive load driving capability is enhanced by using a pull
up resistor to V
+
Figure 4. Typically a pull up resistor con-
ducting 500 µA or more will significantly improve capacitive
load responses. The value of the pull up resistor must be
determined based on the current sinking capability of the
amplifier with respect to the desired output swing. Open loop
gain of the amplifier can also be affected by the pull up
resistor (see Electrical Characteristics).
PRINTED-CIRCUIT-BOARD LAYOUT
FOR HIGH-IMPEDANCE WORK
It is generally recognized that any circuit which must operate
with less than 1000 pA of leakage current requires special
layout of the PC board. When one wishes to take advantage
of the ultra-low bias current of the LMC662, typically less
than 0.04 pA, it is essential to have an excellent layout.
Fortunately, the techniques for obtaining low leakages are
quite simple. First, the user must not ignore the surface
leakage of the PC board, even though it may sometimes
appear acceptably low, because under conditions of high
humidity or dust or contamination, the surface leakage will
be appreciable.
To minimize the effect of any surface leakage, lay out a ring
of foil completely surrounding the LMC662’s inputs and the
terminals of capacitors, diodes, conductors, resistors, relay
terminals, etc. connected to the op-amp’s inputs. See Figure
5. To have a significant effect, guard rings should be placed
on both the top and bottom of the PC board. This PC foil
must then be connected to a voltage which is at the same
voltage as the amplifier inputs, since no leakage current can
flow between two points at the same potential. For example,
a PC board trace-to-pad resistance of 10
12
, which is nor-
mally considered a very large resistance, could leak 5 pA if
the trace were a 5V bus adjacent to the pad of an input. This
would cause a 100 times degradation from the LMC662’s
actual performance. However, if a guard ring is held within
5 mV of the inputs, then even a resistance of 10
11
would
cause only 0.05 pA of leakage current, or perhaps a minor
(2:1) degradation of the amplifier’s performance. See Fig-
ures 6, 7, 8 for typical connections of guard rings for stan-
00976306
CSconsists of the amplifier’s input capacitance plus any stray capacitance
from the circuit board and socket. CFcompensates for the pole caused by
CSand the feedback resistor.
FIGURE 2. General Operational Amplifier Circuit
00976305
FIGURE 3. Rx, Cx Improve Capacitive Load Tolerance
00976323
FIGURE 4. Compensating for Large Capacitive Loads
with a Pull Up Resistor
LMC662
www.national.com 8
Application Hints (Continued)
dard op-amp configurations. If both inputs are active and at
high impedance, the guard can be tied to ground and still
provide some protection; see Figure 9.
The designer should be aware that when it is inappropriate
to lay out a PC board for the sake of just a few circuits, there
is another technique which is even better than a guard ring
on a PC board: Don’t insert the amplifier’s input pin into the
board at all, but bend it up in the air and use only air as an
insulator. Air is an excellent insulator. In this case you may
have to forego some of the advantages of PC board con-
struction, but the advantages are sometimes well worth the
effort of using point-to-point up-in-the-air wiring. See Figure
10.
00976316
FIGURE 5. Example, using the LMC660,
of Guard Ring in P.C. Board Layout
00976317
FIGURE 6. Guard Ring Connections: Inverting
Amplifier
00976318
FIGURE 7. Guard Ring Connections: Non-Inverting
Amplifier
00976319
FIGURE 8. Guard Ring Connections: Follower
00976320
FIGURE 9. Guard Ring Connections: Howland Current
Pump
00976321
(Input pins are lifted out of PC board and soldered directly to components.
All other pins connected to PC board.)
FIGURE 10. Air Wiring
LMC662
www.national.com9
Application Hints (Continued)
BIAS CURRENT TESTING
The test method of Figure 11 is appropriate for bench-testing
bias current with reasonable accuracy. To understand its
operation, first close switch S2 momentarily. When S2 is
opened, then
A suitable capacitor for C2 would be a 5 pF or 10 pF silver
mica, NPO ceramic, or air-dielectric. When determining the
magnitude of I
b
−, the leakage of the capacitor and socket
must be taken into account. Switch S2 should be left shorted
most of the time, or else the dielectric absorption of the
capacitor C2 could cause errors.
Similarly, if S1 is shorted momentarily (while leaving S2
shorted)
where C
x
is the stray capacitance at the + input.
00976322
FIGURE 11. Simple Input Bias Current Test Circuit
LMC662
www.national.com 10
Typical Single-Supply Applications
(V
+
= 5.0 V
DC
)
Additional single-supply applications ideas can be found in
the LM358 datasheet. The LMC662 is pin-for-pin compatible
with the LM358 and offers greater bandwidth and input
resistance over the LM358. These features will improve the
performance of many existing single-supply applications.
Note, however, that the supply voltage range of the LM662 is
smaller than that of the LM358.
Low-Leakage Sample-and-Hold
00976315
Instrumentation Amplifier
00976307
For good CMRR over temperature, low drift resistors should
be used. Matching of R3 to R6 and R4 to R7 affects CMRR.
Gain may be adjusted through R2. CMRR may be adjusted
through R7.
Sine-Wave Oscillator
00976308
Oscillator frequency is determined by R1, R2, C1, and C2:
f
OSC
= 1/2πRC
where R = R1 = R2 and C = C1 = C2.
This circuit, as shown, oscillates at 2.0 kHz with a peak-to-
peak output swing of 4.5V
1 Hz Square-Wave Oscillator
00976309
Power Amplifier
00976310
LMC662
www.national.com11
Typical Single-Supply Applications
(V+= 5.0 V
DC
) (Continued)
10 Hz Bandpass Filter
00976311
fO=10Hz
Q = 2.1
Gain = −8.8
10 Hz High-Pass Filter
00976312
fc=10Hz
d = 0.895
Gain = 1
2 dB passband ripple
1 Hz Low-Pass Filter
(Maximally Flat, Dual Supply Only)
00976313
High Gain Amplifier with
Offset Voltage Reduction
00976314
Gain = −46.8
Output offset voltage reduced to the level of the input offset voltage of the
bottom amplifier (typically 1 mV).
LMC662
www.national.com 12
Physical Dimensions inches (millimeters) unless otherwise noted
Small Outline Dual-In-Line Pkg. (M)
Order Number LMC662AIM, LMC662CM, LMC662AIMX or LMC662CMX
NS Package Number M08A
Molded Dual-In-Line Pkg. (N)
Order Number LMC662AIN, LMC662CN
NS Package Number N08E
LMC662
www.national.com13
Notes
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.
2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.
National Semiconductor
Americas Customer
Support Center
Email: new.feedback@nsc.com
Tel: 1-800-272-9959
National Semiconductor
Europe Customer Support Center
Fax: +49 (0) 180-530 85 86
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
National Semiconductor
Asia Pacific Customer
Support Center
Fax: +65-6250 4466
Email: ap.support@nsc.com
Tel: +65-6254 4466
National Semiconductor
Japan Customer Support Center
Fax: 81-3-5639-7507
Email: jpn.feedback@nsc.com
Tel: 81-3-5639-7560
www.national.com
LMC662 CMOS Dual Operational Amplifier
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TIs terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TIs standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic."Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products Applications
Audio www.ti.com/audio Communications and Telecom www.ti.com/communications
Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers
Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps
DLP®Products www.dlp.com Energy and Lighting www.ti.com/energy
DSP dsp.ti.com Industrial www.ti.com/industrial
Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical
Interface interface.ti.com Security www.ti.com/security
Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Mobile Processors www.ti.com/omap
Wireless Connectivity www.ti.com/wirelessconnectivity
TI E2E Community Home Page e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright ©2011, Texas Instruments Incorporated