19-3961; Rev 0; 1/99 General Description The MAX4601/MAX4602/MAX4603 quad analog switches feature low on-resistance of 2.50 max. On-resistance is matched between switches to 0.50 max and is flat (0.5Q max) over the specified signal range. Each switch can handle Rail-to-Rail analog signals. The off- leakage current is only 2.5nA maximum at Ta = +85C. These analog switches are ideal in low-distortion appli- cations and are the preferred solution over mechanical relays in automatic test equipment or applications where current switching is required. They have low power requirements, require less board space, and are more reliable than mechanical relays. The MAX4601 has four normally closed (NC) switches, the MAX4602 has four normally open (NO) switches, and the MAX46083 has two NC and two NO switches. These switches operate from a single supply of +4.5V to +36V or from dual supplies of +4.5V to +20V. All dig- ital inputs have +0.8V and +2.4V logic thresholds, ensuring TTL/CMOS-logic compatibility when using +15V or asingle +12V supply. Applications Reed Relay Replacement Test Equipment Communication Systems PBX, PABX Systems Audio-Signal Routing MA AXILM 2.5Q, Quad, SPST, CMOS Analog Switches Features @ Low On-Resistance (2.5Q max) Guaranteed Ron Match Between Channels (0.5Q max) # Guaranteed Ron Flatness over Specified Signal Range (0.5Q max) @ Rail-to-Rail Signal Handling # Guaranteed ESD Protection > 2000V per Method 3015.7 @ Single-Supply Operation: +4.5V to +36V Dual-Supply Operation: 4.5V to 20V # TTL/CMOS-Compatible Control Inputs Ordering Information PART TEMP. RANGE PIN-PACKAGE MAX4601CAE 0C to +70C 16 SSOP MAX4601 CWE 0C to +70C 16 Wide SO MAX4601 CPE 0C to +70C 16 Plastic DIP MAX4601EAE -40C to +85C 16 SSOP MAX4601 EWE -40C to +85C 16 Wide SO MAX4601EPE -40C to +85C 16 Plastic DIP Ordering Information continued at end of data sheet. Avionics . . . . . Pin Configurations/Functional Diagrams/Truth Tables TOP VIEW V7 XV VS mw Hil w EED <Hne GED Heal oe COM! bos pots] com2 coMt [ef-oa) 5] come COM! fo a~o-fa com2 net [3 | ha] Nez noi [3 | ha] nee noi [3 | Ha] nce Ly pax [2] LE} pax [2] Lb] anaxim fel eno [5] Mmax4eor fra] ve eno [5] MAX4602 fia] vy eno [5] MAx4603 fra] vy nea [6 | it] Nes nos [6 ht] Nos now [6 Ht] Nea com4 Fo! Lota] cos coma noe 4 ofa cos coma Foy! Lota coma na [BEY PHS] ne na [8B <H{2] ins ng BED! fH] ine SSOP/SO/DIP SSOP/SO/DIP SSOP/SO/DIP MAXA6O1 MAX4602 MAX4603 LOGIC SWITCH LoGic SWITCH Logic SWITCHES | SWITCHES 0 ON 0 OFF uf a8 1 OFF 1 ON 0 OF ON 1 ON OFF SWITCHES SHOWN FOR LOGIC 0 INPUT Rail-to-Rail is a registered trademark of Nippon Motorola, Ltd. MAXIMA Maxim Integrated Products 1 For free samples & the latest literature: http:/1vwww.maxim-ic.com, or phone 1-800-998-8800. For small orders, phone 1-800-835-8769. CO9OVXVW/cOIOVXVW/LOIOVPXVWNMAX4601/MAX4602/MAX4603 2.5Q, Quad, SPST, CMOS Analog Switches ABSOLUTE MAXIMUM RATINGS V+ to GND oon eee nnienence encase enna -0.3V to +44V V- tO GND oo enters renee ene +0.3V to -44V V4 10 Votes n neo seeetneanoeenencoeeeeesneasneeeae -0.3V to +44V VLE to GND once (GND - 0.3V) to (V+ + 0.3V) All Other Pins to DGND (Note 1) ......... (V- - 0.3V) to (V+ + 0.3V) Continuous Current (COM_, NO_, NC_) woe +200mA Peak Current (COM_, NO_, NC_) (pulsed at ims, 10% duty cycle)... eee eee +300mA Continuous Power Dissipation (Ta = +70C) 16 SSOP (derate 7.1MW/C above +70C) oo... 16 Wide SO (derate 9.52mW/C above +70C) 16 Plastic DIP (derate 10.53mW/C above +70C) ...... 842mW Operating Temperature Ranges MAX460_C_E ose eens eeenee ween eaeeneneed 0C to +70C MAX460_ EE ooo. ee ee nce snes eeeeneeaceneee -40C to +85C Storage Temperature Range... .- 65C to +160C Lead Temperature (soldering, 10S@C) ........ceeese eee +300C Note 1: Signals on NC_, NO_, COM_, or IN_ exceeding V+ or V- will be clamped by internal diodes. Limit forward diode current to maxi- mum current rating. Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICSDual Supplies (V+ = +15V, V- = -15V, VL = 5V, VIN_H = 2.4V, VIN_L = 0.8V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at Ta = +25C.) PARAMETER SYMBOL CONDITIONS MIN (Note 2) MAX UNITS ANALOG SWITCH Input Voltage Range vane (Note 3) V- V+ Vv COM_to NO or NC__ R Icom_ = 10mA, Ta = +25C 1.7 2.5 On-Resistance ON VNo_or Vnc_= 410V |Ta = Tyin to TMAX 2.7 COM_to NO_ or NC_ Ta = +25C 0.1 On-Resistance Match Between ARON CoM = om No Q Channels (Note 4) = NNC_= = TA = TMIN to TMAX 0.5 COM_to NO_orNC_ R Icom = 10mA;VNo_ [TA = +25C 0.4 0.4 o On-Resistance Flatness (Note 5) FLAT(ON) or VNc_ = -5V,0,5V | Ta = Tyin to Tuax 0.5 Off-Leakage Current Vcom_ = 10V, TA = +25C -0.5 0.01 0.5 aA (NO_ or NC_) (Note 6) NOW INC_ | Wno_or Vnc = 10V [Ta =Tminto Twax | -2.5 2.5 COM Off-Leakage Current Vcom_ = 10V, Ta = 425C -0.5 0.01 0.5 aA (Note 6) COM_(OFF) VNo_or Vnc_ = 10V /T, = Tyin to TMAX -2.5 2.5 - Vcom_ = +10V, Ta = +25C -1 0.2 1 (Note 8) Leakage Current Icom (on) | VNo_ or Vwc = #10V nA or floating Ta = TMIN to TMAX -10 10 LOGIC INPUT Hon Current with Input Voltage INH IN_ = 2.4V, all others = 0.8V 0.500 0.001 0.500] pA put Current with Input Voltage INL IN_ = 0.8V, all others = 2.4V 0.500 0.001 0.500] pA Logic Input High Voltage VIN_-H 2.4 1.7 Vv Logic Input Low Voltage VIN-L 1.7 0.8 Vv 2 MAXIMA2.5Q, Quad, SPST, CMOS Analog Switches ELECTRICAL CHARACTERISTICSDual Supplies (continued) (V+ = +15V, V- = -15V, VL = 5V, VIN_H = 2.4V, VIN L = 0.8V, Ta = Twin to TMAX, unless otherwise noted. Typical values are at TA = +25C.) CO9OVXVW/cOIOVXVW/LOIOVPXVWN PARAMETER | SYMBOL | CONDITIONS | MIN TYP MAX | UNITS POWER SUPPLY Power-Supply Range +4.5 +20.0 Vv Ta = +25C -0.5 0.001 0.5 Positive Supply Current l+ * channels on or off, | VA HA IN =O or 5V Ta = TMIN to TMAX 5 5 . All channels on or off, | TA = +25C -0.5 0.001 0.5 Negative Supply Current - Vv 0 or 5V HA IN = UY or Ta = TMIN to Tmax 5 5 . All channels on or off, | TA = +25C -0.5 0.001 0.5 Logic Supply Current IL Vin = 0 or 5V T pA = A= TMIN to Tmax 5 5 G All channels on or off, | TA = +25C -0.5 0.001 0.5 round Current IGND Vin = 0 or 5V HA IN = Ta = TMIN to TMAX -5 5 SWITCH DYNAMIC CHARACTERISTICS Turn-On Time ton Figure 2, Vcom_ = 10V, Ta = +25C 160 250 ns Turn-Off Time toFF Figure 2, Vcom_ = 10V, Ta = +25C 190 350 ns Charge Injection Q woe ore VGEN = 0, Raen = 0, Figure 3, 420 pc Otf-Isolation (Note 7) Viso rt = oon 5pF, f = 1MHz, Figure 4, 56 dB Crosstalk (Note 8) Vet rt = ee = 5pF, f = 1MHz, Figure 5, 59 dB NC_or NO_ Capacitance C(OFF) f = 1MHz, Figure 6, Ta = +25C 55 pF COM Off-Capacitance C(com) f = 1MHz, Figure 6, Ta = +25C 55 pF On-Capacitance C(com) f = 1MHz, Figure 7, Ta = +25C 250 pF MA AXIAMA 3MAX4601/MAX4602/MAX4603 2.5Q, Quad, SPST, CMOS Analog Switches ELECTRICAL CHARACTERISTICSSingle +12V Supply (V+ = 12V, V- = 0, VL = 5V, VIN_H = 2.4V, VIN _L = 0.8V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at Ta = +25C.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX | UNITS (Note 2) ANALOG SWITCH Input Voltage Range Noo WNO.; (Note 3) GND V+ Vv COM_to NO or NC_ R Icom. = 10mA, Ta = +25C 3 4 On-Resistance ON VNo_or Vnc_= 10V_ [Ta = Tyin to Tmax 5 COM_to NO_ or NC_ Ta = +25C 0.03 0.4 On-Resistance Match Between ARON COM = tomy WNO_ Q Channels (Note 4) = NG_= Ta = TIN to Tmax 0.5 COM_to NO_or NC_ _ . Ta = +25C 0.1 0.4 On-Resistance Flatness RFLAT(ON) COM = oA SV Q (Note 5) NC_= oN, OV, Ta = TMIN to TMAXx 0.5 Off-Leakage Current INO Vcom_= 1V, 10V;, Ta = 425C 05 0.01 0.5 NO NC ) (Notes 6. 9 Vno_or Vnc_ = 10V, nA (NO_ or NC_) (Notes 6, 9) INC_ iV TA=TMINtoO TMAX | -2.5 2.5 COM Off-Leakage Current ICOM (OE VnNo_orVnc_=10V, |TA=+25C -0.5 0.01 0.5 aA (Notes 6, 9) HOFF) | 4V;Vcom_=1V, 10V |T,a=TwintoTwax | -25 25 COM On-Leakage Current Vcom_= 1V,10V; TA = +25C 4 0.01 1 (Notes 6, 9) Icom_(ON) | VNO_or VNc_ = 1V, nA , 10V, or floating Ta = TMIN to TMAx -10 10 LOGIC INPUT Hon Current with Input Voltage INH IN_ = 2.4V, all others = 0.8V 0.500 0.001 0.500] pA put Current with Input Voltage INL IN_ = 0.8V, all others = 2.4V 0.500 0.001 0.500] pA Logic Input High Voltage VIN_-H 2.4 Vv Logic Input Low Voltage VIN-L 0.8 Vv POWER SUPPLY Power-Supply Range 4.5 36.0 Vv Ta = +25C -0.5 0.001 0.5 Positive Supply Current l+ All channels on or off, A HA VIN =O or 5V Ta = TmMIN to TMAX -5 5 . All channels on or off, | TA = +25C -0.5 0.001 0.5 Logic Supply Current IL Vin = Oor5V pA IN = Ta = TmIn to TMAX 5 5 Ta = +25C -0.5 0.001 0.5 Ground Current IGND Vin =O or 5V HA Ta = TMIN to TMAX -5 5 MAXUMELECTRICAL CHARACTERISTICSSingle +12V Supply (continued) 2.5Q, Quad, SPST, CMOS Analog Switches (V+ = 12V, V- = 0, VL = 5V, VIN_H = 2.4V, VIN _L = 0.8V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX | UNITS (Note 2) SWITCH DYNAMIC CHARACTERISTICS Turn-On Time ton Figure 2, Vcom_ = 10V, Ta = +25C 160 ns Turn-Off Time toFF Figure 2, Vcom_ = 10V, Ta = +25C 170 ns oo. CL = 1.0nF, VGEN = 0, RGEN = 0, Figure 3, Charge Injection Q Ta = +25C 20 pc RL = 50Q, CL= 5pF, f = 1MHz, Figure 5, . Crosstalk (Note 8) VeT Ta = +25C 60 dB NC_or NO_ Capacitance Corr) f = 1MHz, Figure 6, Ta = +25C 85 pF COM Off-Capacitance C(com) f = 1MHz, Figure 6, Ta = +25C 85 pF On-Capacitance C(com) f = 1MHz, Figure 7, Ta = +25C 140 pF Note 2: The algebraic convention, where the most negative value is a minimum and the most positive value a maximum, is used in this data sheet. Note 3: Guaranteed by design. Note 4: ARON = RON(MAX) - RON(MIN). Note 5: Flatness is defined as the difference between the maximum and minimum value of on-resistance as measured over the specified analog signal range. Note 6: Leakage parameters are 100% tested at maximum-rated hot temperature and guaranteed by correlation at +25C. Note 7: Off-isolation = 20 logio [Vcom / (VNC or VNO)], Vcom = output, VNC or VNO = input to off switch. Note 8: Between any two switches. Note 9: Leakage testing at single supply is guaranteed by testing with dual supplies. MA AXIAMA CO9OVXVW/cOIOVXVW/LOIOVPXVWNMAX4601/MAX4602/MAX4603 Q (pe) 2.5Q, Quad, SPST, CMOS Analog Switches (Ta = +25C, unless otherwise noted.) ton, torr (ns) Qo mo oOo Fo DN oO 300 200 100 -100 -200 -300 ON-RESISTANCE vs. Voom (SINGLE SUPPLY) 4,00 3.50 3,00 __ 2.50 a 200 1.50 1.00 0.50 0 2 4 6 8 10 12 14 16 18 20 22 24 Voom (V) CHARGE INJECTION vs. Vcom V+=15V V- =-15V MAX4801 toc 04 V+ =15V =0 < |_X anna I+, |- (nA) \ XK we Voom (V) TURN- ON/OFF TIME vs. SUPPLY VOLTAGE Voom=10V. 8 R=1002 2 C.=35pF dE @ 150 3B 1112 13 14 15 16 17 18 19 20 Vt=V- (V) ON- RESISTANCE vs. Vcom AND TEMPERATURE (SINGLE SUPPLY) Ta = 485C MAX4801 toc 02 Ta=+25C Ta=-40C V+=12V 012 3 45 6 7 8 9 10 11 12 Vom (V) POWER: SUPPLY CURRENT vs. TEMPERATURE MAX4801 toc 05 40 -20 O 2 40 60 80 100 TEMPERATURE (C) TURN- ON/OFF TIME vs. Vcom A. =1002 C. = 35pF MAX4801 toc 08 100k 250 200 150 ton, torr (ns) 100 50 LOSS (dB) Typical Operating Characteristics ON/OFF- LEAKAGE CURRENT vs. TEMPERATURE MAX4801 toc 03 OFF- LEAKAGE 40-20 0 2 40 60 280 100 TEMPERATURE (C) TURN- ON/OFF TIME vs. TEMPERATURE T 8 Voom = 10V 3 R. =1000 Z LC, = 35pF 3 tore _ en _ -40 15 10 35 60 85 TEMPERATURE (C) FREQUENCY RESPONSE MAX4601 toc 09 180 ON- RESPONSE 90 -0 90 ON- PHASE -180 g z -270 ur -360 = - ISOLATION ao -450 -540 -630 -720 0.1 1 10 100 FREQUENCY (MHz) MAXUM2.5Q, Quad, SPST, CMOS Analog Switches Typical Operating Characteristics (continued) (Ta = +25C, unless otherwise noted.) ON- RESISTANCE vs. Voom ON- RESISTANCE vs. Voom AND TEMPERATURE (DUAL SUPPLIES) V+, V- = 45V V+, V- =t15V MAX4801 toc 10 V+, V- = #20V (DUAL SUPPLIES) 2.50 2.25 200 Ta = +85C MAX4801 toc 11 1.7 1.50 5 1.25 1.00 0.75 Ta=+25C 0.50 0.25 Ta=-40C V+, V- =t15V 200-15 -10 -5 0 10 15 20 15 -10 5 0 5 10 15 Veom () Veom () Pin Description PIN NAME FUNCTION MAX4601 | MAX4602 | MAX4603 IN1, IN2, . a 1,16,9,8 1,16,9,8 1,16,9,8 IN3, IN4 Logic-Control Digital Inputs 2, 15, 2, 15, 2, 15, COM1, COM2, . . 10,7 10,7 10,7 COM3, COM4 Analog Switch Common Terminals NC1, NC2, . . 3,14, 11,6 _ _ NC3, NC4 Analog Switch Normally Closed Terminals NO1, NO2, . . _ 3,14,11,6 _ NO3, NO4 Analog Switch Normally Open Terminals _ _ 3,6 NO1, NO4 Analog Switch Normally Open Terminals _ _ 14,11 NC2, NC3 Analog Switch Normally Closed Terminals 4 4 4 V- Negative Analog Supply-Voltage Input. Connect to GND for single- supply operation. 5 5 5 GND Ground 12 12 12 VL Logic-Supply Input 13 13 13 V+ Positive Analog Supply Input MA AXIAMA CO9OVXVW/cOIOVXVW/LOIOVPXVWNMAX4601/MAX4602/MAX4603 2.5Q, Quad, SPST, CMOS Analog Switches Applications Information Overvoltage Protection Proper power-supply sequencing is recommended for all CMOS devices. Do not exceed the absolute maxi- mum ratings, because stresses beyond the listed rat- ings can cause permanent damage to the devices. Always sequence V+ on first, then V-, followed by the logic inputs, NO, or COM. If power-supply sequencing is not possible, add two small signal diodes (D1, D2) in series with the supply pins for overvoltage protection (Figure 1). Adding diodes reduces the analog signal range to one diode drop below V+ and one diode drop above V-, but does not affect the devices low switch resistance and low leakage characteristics. Device operation is unchanged, and the difference between V+ and V- should not exceed 44V. These protection diodes are not recommended when using a single supply. Off-lsolation at High Frequencies In 50Q systems, the high-frequency on-response of these parts extends from DC to above 100MHz with a typical loss of -2dB. When the switch is turned off, how- ever, it behaves like a capacitor, and off-isolation decreases with increasing frequency. (Above 300MHz, the switch actually passes more signal turned off than turned on.) This effect is more pronounced with higher source and load impedances. Above 5MHz, circuit board layout becomes critical, and it becomes difficult to characterize the response of the switch independent of the circuit. The graphs shown in the Typical Operating Characteristics were taken using a 50Q source and load connected with BNC connec- tors to a circuit board deemed average; that is, designed with isolation in mind, but not using strip-line or other special RF circuit techniques. For critical appli- cations above 5MHz, use the MAX440, MAX441, and MAX442, which are fully characterized up to 160MHz. +15V v DI MAXIM Ve MAX4601 MAX4602 MAX4603 COM_ + NO_ V- D2 * INTERNAL PROTECTION DIODES = - 15V Figure 1. Overvoliage Protection Using External Blocking Diodes Timing Diagrams/Test Circuits tr < 20ns Loaic tf < 20ns INPUT SWITCH OUTPUT LOGIC INPUT WAVEFORMS INVERTED FOR SWITCHES THAT HAVE THE OPPOSITE LOGIC SENSE MAXUM MAX4601 MAX4602 48V +18V MAX4603 | | SWITCH VL V+ SWITCH ogy | COM_ 7 NO OUTPUT Yo Input oO i ORNG_ ' RL CL 1002 35pF > | FT GND = = Logic u INPUT ! | 0 -5V REPEAT TEST FOR EACH SWITCH. FORLOAD CONDITIONS, SEE Bectrical Characteristics. G INCLUDES FIXTURE AND STRAY CAPACITANCE BL Vo= Voom (a AG) Figure 2. Switching-Time Test Circuit 8 MAXUM2.5Q, Quad, SPST, CMOS Analog Switches Timing Diagrams/Test Circuits (continued) MAXIM MAX4601 MAX4602 +5V +15V AY MAX4603 | | 0 \ VL V+ Vo COM y4__NCOR Yo ! NO | Vin C OFF OFF Ven =" L ON 1 GND A V- [ = tL | = ON = = ~15V OFF OFF Vin Q = (AV) (C,) | Yin=#8V Vin DEPENDS ON SWITCH CONFIGURATION; = INPUT POLARITY DETERMINED BY SENSE OF SWITCH. Figure 3. Charge-Injection Test Circuit MA AXIAA MAXIM MAX4601 MAX4601 C +H5V 5V MAX4602 , * MAX4602 IH | MAX4603 dl [-4 | MAX4603 SIGNAL t SIGNAL = " "7 GENERATOR odBm ~ GENERATOR cB COMI Not 8 = we 0, 2.4V CX |NcoRNo ai T ANALYZER +15V +5V Figure 4. Off-isolation Test Circuit MA AXIAMA Figure 5. Crosstalk Test Circuit CO9OVXVW/cOIOVXVW/LOIOVPXVWNMAX4601/MAX4602/MAX4603 2.52, Quad, SPST, CMOS Analog Switches Timing Diagrams/Test Circuits (continued) CAPACITANCE METER , NC ORNO +9 f = 1MHz -15V 1 1 | IN aane-- <}++ DAV MNAXIAN MAX4601 +15V +5V MAx4602 C MAX4603 _ V+ VL COM Oor a MAXLAV +15V 45V MAX4601 C MAX4602 co H+ MAX4603 = Vt VL COM CAPACITANCE METER t __. <ey 0 or f=1MHz 2.4V = NC ORNO GND V- Cc I -15V Figure 6. Switch Off-Capacitance Test Circuit __ Ordering Information (continued) PART TEMP. RANGE PIN-PACKAGE MAX4602CAE oc to +70C 16 SSOP MAX4602CWE oc to +70C 16 Wide SO MAX4602CPE oc to +70C 16 Plastic DIP MAX4602EAE -40C to +85C 16 SSOP MAX4602EWE -40C to +85C 16 Wide SO MAX4602EPE -40C to +85C 16 Plastic DIP MAX4603CAE oc to +70C 16 SSOP MAX4603CWE oc to +70C 16 Wide SO MAX4603CPE oc to +70C 16 Plastic DIP MAX4603EAE -40C to +85C 16 SSOP MAX4603EWE -40C to +85C 16 Wide SO MAX4603EPE -40C to +85C 16 Plastic DIP 10 Figure 7. Switch On-Capacitance Test Circuit Chip Information TRANSISTOR COUNT: 100 MAXUM2.5Q, Quad, SPST, CMOS Analog Switches Package Information SSOP.EPS. a See INCHES MILLIMETERS DIM| MIN | MAX | MIN | MAX MIN | Max | MIN | MAX 0.068 [0.078 | 1.73 | 1.99 ; ; 07 | 6. 14L 0.002 [0.008 | 0.05 | 0.21 0.239 10.249 | 6.0 6.33 0.239 |0.249 | 6.07 | 6.33 | 16L ood a aS oe 0.27810.289 | 7.07| 7.33] 20L SEE VARIATIONS oo Naas Oo aaa e4L 0.205 [0.209 | 5.20 | 5.38 0.397 /0.407 |10.07 | 10.33 | 28L 0.0256 BSC |0.65 BSC 0.301 [0.311 | 7.65 | 7.90 0.025 [0.037 | 0.63 | 0.95 0 8 0 8 Oyo /o|v0}/o a a [ a a + a m x= Q}r|XI]o |mM|olo}w/ >| > DRE DO NOT INCLUDE MOLD FLASH. MV MM A I VI PROPRIETARY INFORMATION 2, MOLD FLASH OR PROTRUSIONS NOT TO Te EXCEED 15mm (006%) PACKAGE OUTLINE, SSOP, 5.3X.65mm APPROVAL DOCUMENT CONTROL NO REV 3, CONTROLLING DIMENSION: MILLIMETER 21-0056 a MAXIM 11 CO9OVXVW/cOIOVXVW/LOIOVPXVWNMAX4601/MAX4602/MAX4603 2.5Q, Quad, SPST, CMOS Analog Switches Package Information SOIOW EPS. { 4 } } i A _ 0-g eel be ple Vy re i INCHES MILLIMETERS INCHES ILLIMETERS MIN MAX | MIN | MAX IN MAX | MIN AX |N 0.093[0,104 |2.35| 2.65 0.004 | 0.012 |0.10 | 0.30 0.014 | 0.019 |0.35| 0.49 0.009 | 0.013 |0.2e3|0.3e 0.050 1.27 0.291 | 0.299] 7.40] 7.60 NOTES: 0.394| 0.419 | 10,00) 10.65 1. D&& DO NOT INCLUDE MOLD FLASH 0.010 |0.030|0.e2e5]|0,75 2. MOLD FLASH OR PROTRUSIONS NOT TO EXCEED 15mm ,006") 0.016 | 0.050 | 0.40 | 127 LEADS TO BE COPLANAR WITHIN 102mm .004*) CONTROLLING DIMENSION: MILLIMETER MEETS JEDEC MS013-XX AS SHOWN IN ABOVE TABLE 6. N = NUMBER OF PINS MAXIMA JPackace FAMILY OUTLINE: SOIC a") 21-0042 A K|S] 2 [mje jo|w|E}> uk WwW Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 12 Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 1999 Maxim Integrated Products Printed USA MAXIMA is a registered trademark of Maxim Integrated Products.