X5R Dielectric General Specifications GENERAL DESCRIPTION * General Purpose Dielectric for Ceramic Capacitors * EIA Class II Dielectric * Temperature variation of capacitance is within 15% from -55C to +85C * Well suited for decoupling and filtering applications * Available in High Capacitance values (up to 100F) PART NUMBER (SEE PAGE 2 FOR COMPLETE PART NUMBER EXPLANATION) 1210 4 D 107 M A T 2 A Size (L" x W") Voltage 4 = 4V 6 = 6.3V Z = 10V Y = 16V 3 = 25V D = 35V 5 = 50V Dielectric D = X5R Capacitance Code (In pF) 2 Sig. Digits + Number of Zeros Capacitance Tolerance K = 10% M = 20% Failure Rate A = N/A Terminations T = Plated Ni and Sn Packaging 2 = 7" Reel 4 = 13" Reel 7 = Bulk Cass. 9 = Bulk Special Code A = Std. NOTE: Contact factory for availability of Tolerance Options for Specific Part Numbers. Contact factory for non-specified capacitance values. Temperature Coefficient 20 % Capacitance 15 10 5 0 -5 -10 -15 -20 -60 -40 -20 0 +20 +40 Temperature C +60 +80 Insulation Resistance (Ohm-Farads) TYPICAL ELECTRICAL CHARACTERISTICS Insulation Resistance vs Temperature 10,000 1,000 100 0 0 20 40 60 80 100 120 Temperature C 23 X5R Dielectric Specifications and Test Methods Parameter/Test Operating Temperature Range Capacitance Insulation Resistance X5R Specification Limits -55C to +85C Within specified tolerance 2.5% for 50V DC rating 3.0% for 25V DC rating 12.5% Max. for 16V DC rating and lower Contact Factory for DF by PN 10,000M or 500M - F, whichever is less Dielectric Strength No breakdown or visual defects Dissipation Factor Resistance to Flexure Stresses Appearance Capacitance Variation Dissipation Factor Insulation Resistance Solderability Resistance to Solder Heat Thermal Shock Load Life Load Humidity 24 Appearance Capacitance Variation Dissipation Factor Insulation Resistance Dielectric Strength Appearance Capacitance Variation Dissipation Factor Insulation Resistance Dielectric Strength Appearance Capacitance Variation Dissipation Factor Insulation Resistance Dielectric Strength Appearance Capacitance Variation Dissipation Factor Insulation Resistance Dielectric Strength No defects 12% Measuring Conditions Temperature Cycle Chamber Freq.: 1.0 kHz 10% Voltage: 1.0Vrms .2V For Cap > 10 F, 0.5Vrms @ 120Hz Charge device with rated voltage for 120 5 secs @ room temp/humidity Charge device with 300% of rated voltage for 1-5 seconds, w/charge and discharge current limited to 50 mA (max) Deflection: 2mm Test Time: 30 seconds 1mm/sec Meets Initial Values (As Above) Initial Value x 0.3 95% of each terminal should be covered with fresh solder No defects, <25% leaching of either end terminal 90 mm Dip device in eutectic solder at 230 5C for 5.0 0.5 seconds 7.5% Meets Initial Values (As Above) Dip device in eutectic solder at 260C for 60 seconds. Store at room temperature for 24 2 hours before measuring electrical properties. Meets Initial Values (As Above) Meets Initial Values (As Above) No visual defects Step 1: -55C 2 30 3 minutes 7.5% Step 2: Room Temp 3 minutes Meets Initial Values (As Above) Step 3: +85C 2 30 3 minutes Meets Initial Values (As Above) Step 4: Room Temp 3 minutes Meets Initial Values (As Above) No visual defects 12.5% Initial Value x 2.0 (See Above) Initial Value x 0.3 (See Above) Meets Initial Values (As Above) No visual defects 12.5% Repeat for 5 cycles and measure after 24 2 hours at room temperature Charge device with 1.5X rated voltage in test chamber set at 85C 2C for 1000 hours (+48, -0). Note: Contact factory for *optional specification part numbers that are tested at < 1.5X rated voltage. Remove from test chamber and stabilize at room temperature for 24 2 hours before measuring. Store in a test chamber set at 85C 2C/ 85% 5% relative humidity for 1000 hours (+48, -0) with rated voltage applied. Initial Value x 2.0 (See Above) Initial Value x 0.3 (See Above) Meets Initial Values (As Above) Remove from chamber and stabilize at room temperature and humidity for 24 2 hours before measuring. X5R Dielectric Capacitance Range PREFERRED SIZES ARE SHADED SIZE 0201 0402 0603 0805 1206 1210 1812 Soldering Packaging Reflow Only All Paper Reflow/Wave All Paper Reflow/Wave All Paper Reflow/Wave Paper/Embossed Reflow/Wave Paper/Embossed Reflow Only Paper/Embossed Reflow Only All Embossed 0.60 0.03 (0.024 0.001) 0.30 0.03 (0.011 0.001) 0.15 0.05 (0.006 0.002) 4 6.3 10 16 25 1.00 0.10 (0.040 0.004) 0.50 0.10 (0.020 0.004) 0.25 0.15 (0.010 0.006) 4 6.3 10 16 25 50 100 150 220 A A A C 330 470 680 A A A C C C A C C C 0.010 0.015 0.022 A 0.033 0.047 0.068 0.10 0.15 0.22 A 0.33 (0.013) C A* C C C C C C A* C A* A* G G G G G G G G G G G G C* G G C* C* G G G G G J* C* C* G* G* J* J* J* E* J* J* K C* C* C* G 4 6.3 10 16 25 4 6.3 10 16 25 50 0201 0402 C 0.56 (0.022) t G G C C C A* 3.3 4.7 10 Letter Max. Thickness T C 1.0 1.5 2.2 SIZE W C C 0.33 0.47 0.68 22 47 100 WVDC A A A L A 3300 4700 6800 A A A Cap (F) 1000 1500 2200 3.20 0.20 4.50 0.30 (0.126 0.008) (0.177 0.012) 2.50 0.20 3.20 0.20 (0.098 0.008) (0.126 0.008) 0.50 0.25 0.61 0.36 (0.020 0.010) (0.024 0.014) 4 6.3 10 16 25 35 50 6.3 10 25 50 Cap (pF) 2.01 0.20 3.20 0.20 (0.079 0.008) (0.126 0.008) 1.25 0.20 1.60 0.20 (0.049 0.008) (0.063 0.008) 0.50 0.25 0.50 0.25 (0.020 0.010) (0.020 0.010) 10 16 25 35 50 6.3 10 16 25 35 50 (t) Terminal 1.60 0.15 (0.063 0.006) 0.81 0.15 (0.032 0.006) 0.35 0.15 (0.014 0.006) 4 6.3 10 16 25 35 50 6.3 (W) Width mm (in.) mm (in.) mm (in.) WVDC (L) Length E 0.71 (0.028) PAPER G 0.90 (0.035) J* J* J* J* J* G G G N G G G N N N G N N N N N N Q N N N N N N N N P* Q Q Q Q Q Q Q Q Q* N N N N N* N* N* N* N* * Q Q Q N* * Q* Q* Q* Q* * Q Q Q Q X X Q Z X X Z X Z Z* X Z Z Z Z Z* Z* Z* Z* 4 6.3 10 16 25 35 50 6.3 10 16 25 35 50 6.3 10 16 25 35 50 4 6.3 10 16 25 35 50 6.3 10 25 50 0603 J 0.94 (0.037) K 1.02 (0.040) 0805 M 1.27 (0.050) N 1.40 (0.055) P Q 1.52 1.78 (0.060) (0.070) EMBOSSED 1206 X 2.29 (0.090) 1210 Y 2.54 (0.100) 1812 Z 2.79 (0.110) = Under Development = *Optional Specifications - Contact factory NOTE: Contact factory for non-specified capacitance values 25