CLOVER CHINA DISPLAY ( SHENZHEN) LTD. ( ) LCD MODULE SPECIFICATION Model : CV160160A - _ _ - _ _ - _ _ - _ : : : : 518053 (86)755-26932073 sales@cloverchina.com : http://www.cloverchina.com Revision 01 Engineering Date Yamaha Yam 2003 9 29 Our Reference 4945 B4 : (86)755-26932370 ( ) . CV160160A MODE OF DISPLAY Display mode Display condition Viewing direction STN : Yellow green Grey Blue (negative) FSTN positive FSTN negative Reflective type Transflective type Transmissive type Others 6 O' clock 12 O' clock 3 O' clock 9 O' clock LCD MODULE NUMBER NOTATION: CV160160A- MY - S F - N 6 - T | (1) .01 | | | | | | | (2) (3) (4) (5) (6) (7) (8) *(1)---Model number of standard LCD Modules *(2)---Backlight type N - No backlight E - EL backlight L - Side-lited LED backlight M- Array LED backlight C - CCFL *(3)---Backlight color N - No backlight A - Amber B - Blue O- Orange W-White Y - Yellow green *(4)---Display mode T - TN V - TN (Negative) S - STN Yellow green G - STN Grey B - STN Blue (Negative) F - FSTN N - FSTN (Negative) *(5)---Rear polarizer type R - Reflective F - Transflective T - Transmissive *(6)---Temperature range N - Normal W- Extended *(7)---Viewing direction 6 - 6 O'clock 2 - 12 O'clock 3 - 3 O'clock 9 - 9 O'clock *(8)---Special code for other requirements (Can be omitted if not used) T - Touch panel (Analog) P - Touch panel (Digital) 1 8 ( ) . CV160160A GENERAL DESCRIPTION Display mode : 160x160 dots, Graphic COB LCD module, Interface : 4 bit data transfer Driving method : 1/160 duty, 1/15 bias Driver IC : PTC PT6601, PT6630 or equivalent For the detailed information, please refer to the IC specifications. MECHANICAL DIMENSIONS Item Dimension Unit Item Dimension Unit Outline Dimension 89.2(L)x85.0(W)x(H1/H2) mm Dot Pitch 0.38(L)x0.38(W) mm Viewing Area 62.0(L)x62.0(W) mm Dot Size 0.34(L)x0.34(W) mm Side Backlight (L) No Backlight (N) EL Backlight (E) CCFL Backlight (C) H1 mm H2 mm H1 mm H2 mm H1 mm H2 mm Array Backlight (M) H1 6.35 mm H2 11.0 mm H1 mm H2 mm CONNECTOR PIN ASSIGNMENT Pin No. SYMBOL Function 1 VSS Power Supply (GND) 2 M Alternate signal for LCD drive 3 FLM First Line Marker 4 CL1 Latch Signal 5 CL2 Clock Pulse 6 D3 Data Bus 7 D2 Data Bus 8 D1 Data Bus 9 D0 Data Bus 10 VEE LCD drive supply voltage 11 VDD Logic Power Supply 12 VO Voltage adjust for LCD drive 13 DISPOFF Display off control 14 BKL-K Back Light Supply (-) 15 BKL-A Back Light Supply (+) .01 2 8 ( ) . CV160160A COUNTER DRAWIING OF MODULE DIMENSION .01 3 8 ( ) . CV160160A COUNTER DREWING OF PIN OUT & BLOCK DIAGRAM .01 4 8 ( ) . ELECTRICAL CHARACTERISTICS Item Conditions: VSS=0V, @Ta=25 Symbol MIN. TYP. MAX. Supply Voltage VDD 4.75 5.00 5.25 Supply Current IDD 2.0 Supply Voltage for LCD VO 19.0 Unit Symbol MIN. TYP. MAX. Unit "H"Level Input Voltage VIH 0.8 VDD VDD V mA "L"Level Input Voltage VIL 0 0.2 VDD V V Item V Backlight Voltage EL (@ Frequency 400Hz) CV160160A Backlight Current VEL Vrms Side-lited LED Side-lited LED White VBL 19.5 20.0 20.5 V White IBL 20 22 mA Blue VBL V Blue IBL mA Yellow Green VBL V Yellow Green IBL mA Array LED Array LED Yellow Green VBL V Yellow Green IBL mA Amber VBL V Amber IBL mA Orange VBL V Orange IBL mA Soft Orange VBL V Soft Orange IBL mA IBL mArms CCFL White CCFL VBL Vrms White ABSOLUTE MAXIMUM RATINGS Please make sure not to exceed the following maximum rating values under the worst application conditions Item Symbol Rating (for normal temperature) Rating (for wide temperature) Unit VDD 7 7 V Input Voltage VT -0.3 to VDD +0.3 -0.3 to VDD +0.3 V Operating Temperature Topr 0 to 50 -20 to 70 Storage Temperature Tstg -10 to 60 -30 to 80 Supply Voltage .01 5 8 ( ) . CV160160A TIMING CHART T CL1 CL2 CL1 160 X T DISPLAY AND DATA #1 #160 .01 6 8 ( ) . CV160160A ELECTRO-OPTICAL CHARACTERISTICS MEASURING CONDITION: POWER SUPPLY = VOP / 64 Hz TEMPERATURE = 22 5 C RELATIVE HUMIDITY = 60 15 % ITEM SYMBOL UNIT RESPONSE TIME Ton ms Toff ms CONTRAST RATIO Cr V3:00 VIEWING ANGLE (6 O'clock) V6:00 V9:00 (Cr 2) V12:00 TYP. TN 100 80 10 20 20 20 10 TYP. STN 200 200 10 20 40 20 10 THE ELECTRO-OPTICAL CHARACTERISTICS ARE MEASURED VALUE BUT NOT GUARANTEED ONES. RELIABILITY OF LCD MODULE ITEM High temperature operating Low temperature operating High temperature storage Low temperature storage Temperature-humidity storage Temperature cycling TEST CONDITION FOR NORMAL TEMPERATURE 50C 0C 60C -10C 40C 90% R.H. -10C to 60C 30 Min Dwell TEST CONDITION FOR WIDE TEMPERATURE 70C -20C 80C -30C 60C 90% R.H. -30C to 80C 30 Min Dwell TIME 240 hours 240 hours 240 hours 240 hours 96 hours 5 cycles QUALITY STANDARD OF LCD MODULE 1.0 2.0 Sampling Method Sampling Plan : MIL STD 105 E Class of AQL : Level II/Single Sampling Critical : 0.25% Major 0.65% Minor 1.5% Defect Group Failure Category Critical Defect Malfunction 0.25%(AQL) Major Defect 0.65%(AQL) Poor Insulation Poor Conduction Minor Defect 1.5%(AQL) .01 Cosmetic Defect Failure Reasons Open Short Burnt of dead component Missing part/improper part P.C.B. Broken Potential short High current Component damage or scratched or Lying too close improper coating Damage joint Wrong polarity Wrong spec. part Uneven/intermittent contact Loose part Copper peeling Rust or corrosion or dirt`s Minor scratch Flux residue Thin solder Poor plating Poor marking Crack solder Poor bending Poor packing Wrong size 7 8 ( ) . CV160160A HANDLING PRECAUTIONS (1) CAUTION OF LCD HANDLING & CLEANING Use soft cloth with solvent (recommended below) to clean the display surface and wipe lightly. - Isopropyl alcohol, ethyl alcohol, trichlorotriflorothane Do not wipe the display surface with dry or hard materials that will damage the polarizer surface. Do not use the following solvent; -water, ketone, aromatics (2) CAUTION AGAINST STATIC CHARGE The LCD modules use CMOS LSI drivers, so customers are recommend that any unused input terminal would be connected to VDD or VSS , do not input any signals before power is turned on, and ground your body, work/assembly areas, assembly equipment to protect against static electricity. (3) PACKAGING Avoid intense shock and falls from a height and do not operate or store them exposed direct to sunshine or high temperature/humidity. (4) CAUTION FOR OPERATION It is an indispensable condition to drive LCD's within the specified voltage limit since the higher voltage than the limit causes the shorter LCD life. The use of direct current drive should be avoided because an electrochemical reaction due to direct current causes LCD's undesirable deterioration. Response time will be extremely delayed at low temperature, and LCD's show dark color at high temperature. However those phenomena do not mean malfunction or out of order with LCD's. Some font will be abnormally displayed when the display area is pushed hard during operation. But it resumes normal condition after turning off once. (5) SAFETY For crash damaged or unnecessary LCD's, it is recommended to wash off liquid crystal by either of solvents such as acetone and ethanol and should be burned up later. When any liquid leaked out of a damaged glass cell comes in contact with your hands, wash it off with soap and water. WARRANTY CLOVER will replace or repair any of her LCD module in accordance with her LCD specification for a period of one year from date of shipment. The warranty liability of Clover is limited to repair and/or replacement. Clover will not be responsible for any subsequent or consequential event. .01 8 8