DIR9001 SLES198 - DECEMBER 2006 96-kHz, 24-Bit Digital Audio Interface Receiver FEATURES APPLICATIONS * * * * * * * * * * * * * * * * * * * * * * * * * One-Chip Digital Audio Interface Receiver (DIR) Including Low-Jitter Clock-Recovery System Compliant With Digital Audio Interface Standards: IEC60958 (former IEC958), JEITA CPR-1205 (former EIAJ CP-1201, CP-340), AES3, EBU tech3250 Clock Recovery and Data Decode From Biphase Input Signal, Generally Called S/PDIF, EIAJ CP-1201, IEC60958, AES/EBU Biphase Input Signal Sampling Frequency (fS) Range: 28 kHz to 108 kHz Low-Jitter Recovered System Clock: 50 ps Jitter Tolerance Compliant With IEC60958-3 Selectable Recovered System Clock: 128 fS, 256 fS, 384 fS, 512 fS Serial Audio Data Output Formats: 24-Bit I2S; MSB-First, 24-Bit Left-Justified; MSB-First 16-, 24-Bit Right-Justified User Data, Channel-Status Data Outputs Synchronized With Decoded Serial Audio Data No External Clock Required for Decode Includes Actual Sampling Frequency Calculator (Needs External 24.576-MHz Clock) Function Control: Parallel (Hardware) Functions Similar and Pin Assignments Equivalent to Those of DIR1703 Single Power Supply: 3.3 V (2.7 V to 3.6 V) Wide Operating Temperature Range: -40C to 85C 5 V-Tolerant Digital Inputs Package: 28-pin TSSOP, Pin Pitch: 0,65 mm AV/DVD Receiver, AV Amplifier Car or Mobile Audio System Digital Television Musical Instruments Recording Systems High-End Audio/Sound Card for PC Replacement of DIR1703 Other Applications Requiring S/PDIF Receiver DESCRIPTION The DIR9001 is a digital audio interface receiver that can receive a 28-kHz to 108-kHz samplingfrequency, 24-bit-data-word, biphase-encoded signal. The DIR9001 complies with IEC60958-3, JEITA CPR-1205 (Revised version of EIAJ CP-1201), AES3, EBUtech3250, and it can be used in various applications that require a digital audio interface. The DIR9001 supports many output system clock and output data formats and can be used flexibly in many application systems. As the all functions which the DIR9001 provides can be controlled directly through control pins, it can be used easily in an application system that does not have a microcontroller. Also, as dedicated pins are provided for the channel-status bit and user-data bit, processing of their information can be easily accomplished by connecting with a microcontroller, DSP, etc. The DIR9001 does not require an external clock source or resonator for decode operation if the internal actual-sampling-frequency calculator is not used. Therefore, it is possible to reduce the cost of a system. The operating temperature range of the DIR9001 is specified as -40C to 85C, which makes it suitable for automotive applications. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. SpAct is a trademark of Texas Instruments. All other trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2006, Texas Instruments Incorporated DIR9001 www.ti.com SLES198 - DECEMBER 2006 This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. ABSOLUTE MAXIMUM RATINGS over operating free-air temperature range (unless otherwise noted) VCC (1) Supply voltage VDD VCC to VDD Supply voltage differences AGND to DGND Ground voltage differences Digital input Digital input voltage Analog input voltage UNIT -0.3 to 4 V 0.1 V 0.1 V -0.3 to 6.5 Digital output -0.3 to (VDD + 0.3) < 4 XTI, XTO -0.3 to (VCC + 0.3) < 4 FILT -0.3 to (VCC + 0.3) < 4 V V 10 mA Ambient temperature under bias -40 to 125 C Storage temperature -55 to 150 C Junction temperature 150 C Lead temperature (soldering) 260 C, 5 s Package temperature (reflow, peak) 260 C Input current (any pins except supplies) (1) VALUE Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. RECOMMENDED OPERATING CONDITIONS over operating free-air temperature range (unless otherwise noted) NOM MAX UNIT VCC Analog supply voltage 2.7 3.3 3.6 VDC VDD Digital supply voltage 2.7 3.3 3.6 VDC Digital input clock frequency TA 2 MIN XTI is connected to clock source 24.576 XTI is connected to DGND MHz Not required MHz Digital output load capacitance, except SCKO 20 pF Digital output load capacitance (SCKO) 10 pF 85 C Operating free-air temperature -40 Submit Documentation Feedback DIR9001 www.ti.com SLES198 - DECEMBER 2006 ELECTRICAL CHARACTERISTICS All specifications at TA = 25C, VDD = VCC = 3.3 V (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT DIGITAL INPUT/OUTPUT CHARACTERISTICS VIH VIL VIH VIL VOH VOL IIH IIL IIH IIL IIH IIL 0.7 VDD Input logic level (1) 0.3 VDD 2 Input logic level (2) Output logic level (3) Input leakage current (4) Input leakage current (5) Input leakage current (6) VDD 5.5 0.8 IO = 4 mA 0.85 VDD IO = -4 mA 0.15 VDD VIN = VDD VIN = 0 V 65 -10 100 10 10 VDC VDC VDC A VIN = VDD -10 VIN = 0 V -100 VIN = VDD -10 10 VIN = 0 V -10 10 28 108 kHz 100 ms Bit -65 A A BIPHASE SIGNAL INPUT AND PLL Input sampling frequency range Jitter tolerance -- (IEC60958-3) IEC60958-3 (2003-01) PLL lock-up time From biphase signal detection to error-out release (ERROR = L) Compliant RECOVERED CLOCK AND DATA Serial audio data width SCKO frequency 16 24 128 fS 3.584 13.824 256 fS 7.168 27.648 384 fS 10.752 41.472 MHz 512 fS 14.336 55.296 BCKO frequency 64 fS 1.792 6.912 MHz LRCKO frequency fS 28 108 kHz SCKO jitter fS = 48 kHz, SCKO = 256 fS, measured periodic 100 ps rms SCKO duty cycle 50 45% 55% XTI SOURCE CLOCK XTI is connected to clock source XTI source clock frequency 24.576 MHz Not required XTI is connected to DGND Frequency accuracy XTI is connected to clock source -100 100 XTI input-clock duty cycle XTI is connected to clock source 45% 55% ppm POWER SUPPLY AND SUPPLY CURRENT VCC VDD (1) (2) (3) (4) (5) (6) Operation voltage range 2.7 3.3 3.6 2.7 3.3 3.6 VDC CMOS compatible input: XTI (not 5-V tolerant) 5-V tolerant TTL inputs: RXIN, FMT0, FMT1, PSCK0, PSCK1, CKSEL, RST, RSV CMOS outputs: XTO, SCKO, BCKO, LRCKO, DOUT, UOUT, COUT, BFRAME, ERROR, CLKST, AUDIO, EMPH, FSOUT0, FSOUT1 Internal pulldowns: FMT0, FMT1, PSCK0, PSCK1, CKSEL, RSV Internal pullup: RST No internal pullup and pulldown: RXIN, XTI Submit Documentation Feedback 3 DIR9001 www.ti.com SLES198 - DECEMBER 2006 ELECTRICAL CHARACTERISTICS (continued) All specifications at TA = 25C, VDD = VCC = 3.3 V (unless otherwise noted) PARAMETER ICC Supply current (7) TEST CONDITIONS MIN TYP MAX fS = 96 kHz, PLL locked, XTI connected to DGND 6 8.3 mA fS = 96 kHz, PLL locked, XTI connected to 24.576-MHz resonator 6 8.3 mA RXIN = H or L, XTI = L, RST = L IDD PD Supply current (7) Power dissipation (7) UNIT A 130 fS = 96 kHz, PLL locked, XTI connected to DGND 6 8.3 mA fS = 96 kHz, PLL locked, XTI connected to 24.576-MHz resonator 9 12.4 mA A RXIN = H or L, XTI = L, RST = L 72 fS = 96 kHz, PLL locked, XTI connected to DGND 40 55 mW fS = 96 kHz, PLL locked, XTI connected to 24.576-MHz resonator 50 68 mW RXIN = H or L, XTI = L, RST = L 0.67 mW TEMPERATURE RANGE TA Operation temperature range JA Thermal resistance (7) -40 28-pin T-SSOP 105 C C/W No load connected to SCKO, BCKO, LRCKO, DOUT, COUT, VOUT, BFRAME, FSOUT0, FSOUT1, CLKST, ERROR, EMPH, AUDIO PIN ASSIGNMENTS DIR9001 (TOP VIEW) 4 85 CKSEL 28 ERROR 27 1 AUDIO 2 FSOUT0 3 FSOUT1 FMT1 26 4 SCKO FMT0 5 VDD 6 DGND 7 25 VCC 24 AGND 23 XTO FILT 22 8 XTI RST 21 9 CLKST RXIN 20 10 LRCKO RSV 19 11 BCKO BFRAME 18 12 DOUT EMPH 17 13 PSCK0 UOUT 16 14 PSCK1 COUT 15 Submit Documentation Feedback DIR9001 www.ti.com SLES198 - DECEMBER 2006 TERMINAL FUNCTIONS TERMINAL NAME NO. I/O PULL UP/DOWN REMARKS DESCRIPTION AGND 23 - AUDIO 1 OUT CMOS Channel-status data information of non-audio sample word, active-low BCKO 11 OUT CMOS Audio data bit clock output BFRAME 18 OUT CMOS Indication of top block of biphase input signal CKSEL 28 IN CLKST 9 OUT CMOS Clock change/transition signal output COUT 15 OUT CMOS Channel-status data serial output synchronized with LRCKO DGND 6 - DOUT 12 OUT CMOS 16-bit/24-bit decoded serial digital audio data output EMPH 17 OUT CMOS Channel-status data information of pre-emphasis (50 s/15 s) ERROR 27 OUT CMOS Indication of internal PLL or data parity error FILT 22 - FMT0 25 IN Pulldown 5-V tolerant TTL Decoded serial digital audio data output format selection 0 (1) FMT1 26 IN Pulldown 5-V tolerant TTL Decoded serial digital audio data output format selection 1 (1) FSOUT0 2 OUT CMOS Actual sampling frequency calculated result output 0 FSOUT1 3 OUT CMOS Actual sampling frequency calculated result output 1 LRCKO 10 OUT CMOS Audio data latch enable output PSCK0 13 IN Pulldown 5-V tolerant TTL PLL source SCKO output frequency selection 0 (1) PSCK1 14 IN Pulldown 5-V tolerant TTL PLL source SCKO output frequency selection 1 (1) RST 21 IN Pullup 5-V tolerant TTL Reset control input, active-low RSV 19 IN Pulldown RXIN 20 IN 5-V tolerant TTL SCKO 4 OUT CMOS System clock output UOUT 16 OUT CMOS User data serial output synchronized with LRCKO VCC 24 - Analog power supply, 3.3-V VDD 5 - Digital power supply, 3.3-V XTI 8 IN CMOS Schmitt-trigger XTO 7 OUT CMOS (1) (2) (3) Analog ground Pulldown 5-V tolerant TTL Selection of system clock source, Low: PLL (VCO) clock, High: XTI clock (1) Digital ground External filter connection terminal; must connect recommended filter. (2) Reserved, must be connected to DGND(1) Biphase digital data input (3) Oscillation amplifier input, or external XTI source clock input Oscillation amplifier output TTL Schmitt-trigger input with internal pulldown (51 k typical), 5-V tolerant TTL Schmitt-trigger input with internal pullup (51 k typical), 5-V tolerant TTL Schmitt-trigger input, 5-V tolerant. Submit Documentation Feedback 5 DIR9001 www.ti.com SLES198 - DECEMBER 2006 BLOCK DIAGRAM FILT XTI XTO OSC Sampling Frequency Calculator FSOUT0 FSOUT1 Clock and Data Recovery SCKO RXIN Preamble Detector Charge Pump VCO Divider PLL BCKO Divider Clock Decoder LRCKO Biphase Data Decoder FMT1 Function Control CKSEL Audio Data MUTE Control Power Supply RESET VDD DGND VCC AGND Submit Documentation Feedback DOUT UOUT Channel Status and User Data Output RSV 6 Decoder DGND PSCK1 RST ERROR CLKST Serial Audio Data Formatter FMT0 PSCK0 ERROR Detector COUT BFRAME AUDIO EMPH DIR9001 www.ti.com SLES198 - DECEMBER 2006 TYPICAL PERFORMANCE CHARACTERISTICS Oscillation amplifier operating with crystal; 1-kHz, 0-dB, sine-wave data; no load POWER SUPPLY CURRENT SUPPLY CURRENT vs LOCKED SAMPLING FREQUENCY SUPPLY CURRENT vs LOCKED SAMPLING FREQUENCY 20 20 VCC = VDD = 3.3 V SCKO = 256 fS 18 ICC + IDD - Supply Current - mA ICC + IDD - Supply Current - mA 18 TA = 255C SCKO = 256 fS 16 14 85C 12 -40C 50C 25C -25C 10 0C 16 14 3.3 V 3.6 V 12 10 2.7 V 8 3V 8 6 6 30 40 50 60 70 80 90 100 fS - Sampling Frequency - kHz 30 40 50 60 70 80 fS - Sampling Frequency - kHz G001 Figure 1. 90 100 G002 Figure 2. RECOVERED SYSTEM CLOCK (SCKO) JITTER SCKO JITTER vs LOCKED SAMPLING FREQUENCY 200 VCC = VDD = 3.3 V TA = 255C 180 Periodic Jitter - ps rms 160 128 fS 140 120 256 fS 100 80 384 fS 512 fS 60 40 20 30 40 50 60 70 80 fS - Sampling Frequency - kHz 90 100 G003 Figure 3. Submit Documentation Feedback 7 DIR9001 www.ti.com SLES198 - DECEMBER 2006 DEVICE INFORMATION ACCEPTABLE BIPHASE INPUT SIGNAL AND BIPHASE INPUT PIN (RXIN) The DIR9001 can decode the biphase signal format which is specified in one of the following standards. Generally, these following standards may be called Sony/Philips digital interface format (S/PDIF) or AES/EBU. * IEC60958 (revised edition of former IEC958) * JEITA CPR-1205 (revised edition of former EIAJ CP-1201, CP-340) * AES3 * EBU tech3250 The sampling frequency range and data word length which DIR9001 can decode is as follows: * Sampling frequency range is 28 kHz to 108 kHz. * Maximum audio sample word length is 24-bit. Note of others about the biphase input signal. * The capture ratio of the built-in PLL complies with level III of sampling frequency accuracy (12.5%), which is specified in IEC60958-3. * The jitter tolerance of the DIR9001 complies with IEC60958-3. * The PLL may also lock in outside of the specified sampling-frequency range, but extended range is not assured. Notice about the signal level and transmission line of the biphase input signal. * The signal level and the transmission line (optical, differential, single-ended) are different in each standard. * The biphase input signal is connected to the RXIN pin of the DIR9001. * The RXIN pin has a 5-V tolerant TTL-level input. * An optical receiver module (optical to electric converter) such as TOSLINK, which is generally used in consumer applications, is connected directly to the RXIN pin without added external components. * The output waveform of the optical receiver module varies depending on the characteristics of each product type, so a dumping resistor or buffer amplifier might be required between the optical receiver module output and the DIR9001 input. Careful handling is required if the optical receiver module and the DIR9001 are separated by a long distance. * The DIR9001 needs an external amplifier if it is connected to a coaxial transmission line. * The DIR9001 needs an external differential to single-ended converter, attenuator, etc., for general consumer applications if non-optical transmission line is used. 8 Submit Documentation Feedback DIR9001 www.ti.com SLES198 - DECEMBER 2006 DEVICE INFORMATION (continued) SYSTEM RESET The DIR9001 reset function is controlled by and external reset pin, RST. The reset operation must be performed during the power-up sequence as shown in Figure 4. Specifically, the DIR9001 requires reset operation with a 100-ns period after the supply voltage rises above 2.7 V. 2.7 V VDD RST DIR9001 Status Unknown Reset Operation Min. 100 ns Figure 4. Required System Reset Timing The state of each output pins during reset is shown in Table 1. Table 1. Output-Pin States During Reset Period CLASSIFICATION Clock Data Flag and status Oscillation amplifier PIN NAME WHILE RST = L BCKO L LRCKO L SCKO L DOUT L AUDIO L BFRAME L CLKST L COUT L EMPH L ERROR H FSOUT0 L FSOUT1 L UOUT L XTO Output Submit Documentation Feedback 9 DIR9001 www.ti.com SLES198 - DECEMBER 2006 OPERATION MODE AND CLOCK TRANSITION SIGNAL OUT Operation Mode The DIR9001 has the following three operation modes. These modes are selected by the connection of the CKSEL pin. * PLL MODE: For demodulating a biphase input signal; always outputs PLL source clock * XTI MODE: For clock generator; always outputs XTI source clock * AUTO MODE: Automatic clock source selection; output source depends on ERROR pin. Notes about operation mode selection: * Normally, the PLL mode: CKSEL = L is selected to decode a biphase input signal. * The XTI mode is a mode that supplies the XTI source clock to peripheral devices (A/D converters, etc); therefore, recovered clock and decoded data is not output. * When the XTI source is not used, an XTI source is not required. In this case, clocks are not output in the XTI mode. * At the time of XTI mode selection, biphase decode function continues to operate. Therefore, the biphase input status (ERROR) and the result of the sampling frequency calculator (a required XTI source for operation), are always monitored. That is, the following output pins: ERROR, BFRAME, FSOUT[1:0], CLKST, AUDIO and EMPH are always enabled. The details of these three modes are given in Table 2. Table 2. Operation Mode and Clock Source OPERATION MODE CKSEL PIN SETTING PLL L (1) 10 XTI H AUTO Connected to ERROR pin ERROR PIN STATUS SCKO, BCKO, LRCKO CLOCK SOURCE DOUT DATA AUDIO EMPH FSOUT [1:0] BFRAME COUT UOUT LOW HL LOW LOW H PLL (VCO) free-running clock (1) MUTE (Low) L PLL recovered clock Decoded data OUT OUT OUT OUT H XTI clock MUTE (Low) LOW HL LOW LOW L XTI clock MUTE (Low) OUT OUT OUT LOW H XTI clock MUTE (Low) LOW HL LOW LOW L PLL recovered clock Decoded data OUT OUT OUT OUT The VCO free-running frequency is not a constant frequency, because the VCO oscillation frequency is dependent on supply voltage, temperature, and process variations. Submit Documentation Feedback DIR9001 www.ti.com SLES198 - DECEMBER 2006 FILT XTI XTO OSC Sampling Frequency Calculator FSOUT0 FSOUT1 Clock and Data Recovery SCKO RXIN Preamble Detector Charge Pump VCO Divider PLL BCKO Divider Clock Decoder LRCKO Biphase Data Decoder ERROR Detector ERROR CLKST Decoder CKSEL Serial Audio Data Formatter Audio Data MUTE Control DOUT DGND Figure 5. Clock Source, Source Selector, and Data Path Clock Transition Signal Out The DIR9001 provides an output pulse that is synchronized with the PLL's LOCK/UNLOCK status change. The CLKST pin outputs the PLL status change between LOCK and UNLOCK. The CLKST output pulse depends only on the status change of the PLL. This clock change/transition signal is output through CLKST. As this signal indicates a clock transition period due to a PLL status change, it can be used for muting or other appropriate functions in an application. A clock source selection caused by the CLKSEL pin does not affect the output of CLKST. CLKST does change due to PLL status change even if CKSEL = H in the XTI source mode. When DIR9001 is reset in the state where it is locked to the biphase input signal, the pulse signal of CLKST is not output. That is, the priority of reset is higher than CLKST. The relation among the lock-in/unlock process, the CLKST and ERROR outputs, the output clocks (SCKO, BCKO, LRCKO), and data (DOUT) is shown in Figure 6. Submit Documentation Feedback 11 DIR9001 www.ti.com SLES198 - DECEMBER 2006 DIR9001 Status RXIN Non-Biphase Built-In PLL Status Biphase Non-Biphase Unlock Lock Unlock CLKST tCLKST tCLKST ERROR Lock Up Time PLL Mode [CKSEL = Low] XTI Source XTO SCKO, BCKO, LRCKO PLL Source (Free-Run) DOUT PLL Source (Transition) MUTE (Low) PLL Source (Lock Frequency) PLL Source (Transition) PLL Source (Free-Run) MUTE (Low) Demodulated Data XTI Mode [CKSEL = High] XTO XTI Source SCKO, BCKO, LRCKO XTI Source Always MUTE (Low) DOUT AUTO Mode [CKSEL = ERROR] XTO SCKO, BCKO, LRCKO DOUT XTI Source PLL Source XTI Source MUTE (Low) XTI Source MUTE (Low) Demodulated Data Note: PARAMETERS tCLKST CLKST pulse duration, high MIN 4 Figure 6. Lock-In and Unlock Process 12 means clock source change. Submit Documentation Feedback TYP MAX UNIT 20 s DIR9001 www.ti.com SLES198 - DECEMBER 2006 CLOCK DESCRIPTION System Clock Source DIR9001 has the following two clock sources for the system clock. * PLL source (128 fS, 256 fS, 384 fS, 512 fS are available, recovered by built-in PLL) * XTI source (One 24.576-MHz resonator or external clock source is required.) Two clock sources are used for the following purpose. * PLL source: Recovered system clock from the biphase input signal * XTI source: Clock source for peripheral devices (for example, A/D converter, microcontroller, etc.) Measurement reference clock for the internal actual-sampling-frequency calculator Description of PLL clock source * The PLL clock source is the output clock of built-in PLL (including VCO). * The PLL clock source frequency is selectable from 128 fS, 256 fS, 384 fS, 512 fS by PSCK[1:0]. * When the PLL is in the locked condition, the PLL clock source is the clock recovered from the biphase input signal. * When PLL is in the unlocked condition, the PLL clock source is the built-in free-running clock of the VCO. * The frequency of the PLL clock source in the unlocked condition is not constant. (The VCO free-running frequency is dependent on supply voltage, temperature, and variations in the die's wafer.) Description of XTI clock source * The XTI clock source is not used to recover the clock and decode data from the biphase input signal. * Therefore, if the DIR9001 is used only for recovering the clock and decoding data from the biphase input signal, an XTI clock source is not required. In this case, the XTI pin must be connected to the DGND pin. (The DIR9001 does not have a selection pin for using an XTI clock source or not using one.) The selection method of clock source * The output clock is selected from two clock sources by the level of the CKSEL pin. * The selection of the system clock source depends only on the input level of CKSEL pin. * CKSEL = L setting is required for recovering the clock and decoding data from biphase input. * CKSEL = H setting is required for XTI clock source output. * The continuity of clock during the clock source transition between the XTI source and the PLL source is not assured. Method of automatic clock source selection (CLOCK SOURCE MODE: AUTO) * This method enables selection of the clock source automatically, using the DIR9001 ERROR status. The PLL source clock is output when ERROR = L; the XTI source is output when ERROR = H. * To enable automatic clock source selection, the CKSEL pin must be connected to the ERROR pin. * If XTI clock source is needed during the ERROR period, this method is recommended. * Because the clock source during ERROR status is XTI, if an XTI clock source is not provided to the XTI pin, then SCKO, BCKO, and LRCKO are not output during the ERROR period. The relationship between the clock/data source and the combination of CKSEL pin and PLL status inputs is shown in Table 2. The clock tree system is shown in Figure 7. Submit Documentation Feedback 13 DIR9001 www.ti.com SLES198 - DECEMBER 2006 [PSCK1] [PSCK0] VCO RXIN 1/N CKSEL (I) Built-in PLL Clock Recovery 1/N SCKO (O) 1/N PLL Clock Source BCKO (O) XTI (I) LRCKO (O) 1/4 XTO (O) Oscillation Amplifier Clock Source Selector 1/64 XTI Clock Source Figure 7. Clock Tree Diagram PLL Clock Source (Built-In PLL and VCO) Description The DIR9001 has on-chip PLL (including VCO) for recovering the clock from the biphase input signal. The clock that is output from the built-in VCO is defined as the PLL clock source. In the locked state, the built-in PLL generates a system clock that synchronizes with the biphase input signal. In the unlocked state, the built-in PLL (VCO) generates a free-running clock. (The frequency is not constant.) The PLL can support a system clock of 128 fS, 256 fS, 384 fS, or 512 fS, where fS is the sampling frequency of the biphase input signal. The system clock frequency of the PLL is selected by PSCK[1:0]. The DIR9001 can decode a biphase input signal through its 28 sampling-frequency range of kHz to 108 kHz, independent of the setting of PSCK[1:0]. Therefore, the DIR9001 can decode a biphase input signal with a sampling frequency from 28 kHz to 108 kHz at all settings of PSCK[1:0] The relationship between the PSCK[1:0] selection and the output clock (SCKO, BCKO, LRCKO) from the PLL source is shown in Table 3. Table 3. SCKO, BCKO, and LRCKO Frequencies Set by PSCK[1:0] PSCK[1:0] SETTING PSCK1 14 OUTPUT CLOCK FROM PLL SOURCE PSCK0 SCKO BCKO LRCKO L L 128 fS 64 fS fS L H 256 fS 64 fS fS H L 384 fS 64 fS fS H H 512 fS 64 fS fS Submit Documentation Feedback DIR9001 www.ti.com SLES198 - DECEMBER 2006 In PLL mode (CKSEL = L), output clocks (SCKO, BCKO, LRCKO) are generated from the PLL source clock. The relationship between frequencies of LRCKO, BCKO, and SCKO at different sampling frequencies fS of the biphase input signal are shown in Table 4. Table 4. Output Clock Frequency in PLL Locked State (CKSEL = L) LRCKO BCKO fS 64 fS SCKO (Depending on PSCK[1:0] Setting) 128 fS 256 fS 384 fS 512 fS 32 kHz 2.048 MHz 4.096 MHz 8.192 MHz 12.288 MHz 16.384 MHz 44.1 kHz 2.8224 MHz 5.6448 MHz 11.2896 MHz 16.9344 MHz 22.5792 MHz 48 kHz 3.072 MHz 6.144 MHz 12.288 MHz 18.432 MHz 24.576 MHz 88.2 kHz 5.6448 MHz 11.2896 MHz 22.5792 MHz 33.8688 MHz 45.1584 MHz 96 kHz 6.144 MHz 12.288 MHz 24.576 MHz 36.864 MHz 49.152 MHz Required PLL Loop Filter Description The DIR9001 incorporates a PLL for generating a clock synchronized with the biphase input signal. The built-in PLL requires an external loop filter, which is specified as follows. Operation and performance is assured for recommended filter components R1, C1, and C2. Notes about Loop Filter Components and Layout * The resistor and capacitors which comprise the filter should be located and routed as close as possible to the DIR9001. * A carbon film resistor or metal film resistor, with tolerance less than 5%, is recommended. * Film capacitors, with tolerance is less than 5%, is recommended. * If ceramic capacitors are used for C1 and C2, parts with a low voltage coefficient and low temperature coefficient, such as CH or C0G, are recommended. * The external loop filter must be placed on FILT pins. * The GND node of the external loop filter must be directly connected with the AGND pin of the DIR9001; it must be not combined with other signals. The configuration of external loop filter and the connection with the DIR9001 is shown in Figure 8. DIR9001 PLL Section Charge Pump VCO AGND FILT DGND C2 R1 C1 Figure 8. Loop Filter Connection The recommended values of loop filter components is shown in Table 5. Table 5. Recommended Value of Loop Filter Components REF. NO. RECOMMENDED VALUE PARTS TYPE TOLERANCE R1 680 Metal film or carbon 5% C1 0.068 F Film or ceramic (CH or C0G) 5% C2 0.0047 F Film or ceramic (CH or C0G) 5% Submit Documentation Feedback 15 DIR9001 www.ti.com SLES198 - DECEMBER 2006 XTI Clock Source and Oscillation Amplifier Description This clock, driven by the built-in oscillation amplifier or input into the XTI pin from an external clock, is defined as the XTI source. A 24.576-MHz fundamental resonator or external 24.576-MHz clock is used as the XTI source. The DIR9001 requires an XTI source for following purposes: * The measurement reference clock of actual-sampling-frequency calculator * The clock source for the XTI source mode (CKSEL = H setting) (That is, the DIR9001 does not require an XTI source if it is only decoding the biphase input signal.) The XTI clock source is supplied in one of the following two ways; the details are described in Figure 9. * Setting up an oscillation circuit by connecting a resonator with the built-in amplifier * Applying a clock from an external oscillator circuit or oscillator module To * * * * * set up an oscillation circuit by connecting a resonator with the built-in amplifier: Connect a 24.576-MHz resonator between the XTI pin and XTO pin. The resonator should be a fundamental-mode type. A crystal resonator or ceramic resonator can be used. The load capacitor CL1, CL2, and the current-limiting resistor Rd depend on the characteristics of the resonator. No external feedback resistor between the XTI pin and XTO pin is required, as an appropriate resistor is incorporated in the device. No load other than the resonator is allowed on the XTO pin. To * * * connect an external oscillator circuit or oscillator module: Provide a 24.576-MHz clock on the XTI pin Note that the XTI pin is not 5-V tolerant; it is simple CMOS input. The XTO pin must be open. * Crystal OSC Circuit Resonator XTI CL1 Rd 24.576 MHz Internal Clock XTI External Clock Must Be Open XTO CL2 Crystal OSC Circuit 24.576 MHz Internal Clock XTO DIR9001 DIR9001 Resonator Connection External Clock Input Connection Figure 9. XTI and XTO Connection Diagram Description of oscillation amplifier operation: * The built-in oscillation amplifier is always working. * If the XTI source clock is not used, then the XTI pin must be connected to DGND. * For reducing power dissipation, it is recommended to not use the XTI source clock. In XTI mode (CKSEL = H), output clocks (SCKO, BCKO, LRCKO) are generated from XTI source clock. The relation between output clock frequency (SCKO, BCKO, LRCKO) and the XSCK pin setting in XTI source mode is shown in Table 6. Table 6. SCKO, BCKO, LRCKO Output Frequency at XTI Mode XTI FREQUENCY 24.576 MHz 16 OUTPUT CLOCK FREQUENCY IN XTI SOURCE MODE (CKSEL = H) SCKO BCKO LRCKO 24.576 MHz 6.144 MHz 96 kHz Submit Documentation Feedback DIR9001 www.ti.com SLES198 - DECEMBER 2006 DATA DESCRIPTION Decoded Serial Audio Data Output and Interface Format The DIR9001 supports following 4-data formats for the decoded data. * 16-bit, MSB-first, right-justified * 24-bit, MSB-first, right-justified * 24-bit, MSB-first, left-justified * 24-bit, MSB-first, I2S Decoded data is MSB first and 2s-complement in all formats. The decoded data is provided through the DOUT pin. The format of the decoded data is selected by the FMT[1:0] pins. The data formats for each FMT[1:0] pin setting are shown in Table 7. Table 7. Serial Audio Data Output Format Set by FMT[1:0] FMT[1:0] SETTINGS FMT1 Biphase Signal (IN) DOUT SERIAL AUDIO DATA OUTPUT FORMAT FMT0 L L 16-bit, MSB-first, right-justified L H 24-bit, MSB-first, right-justified H L 24-bit MSB-first, left-justified H H 24-bit, MSB-first, I2S B 0L W 0R M 1L W 1R tLATE BFRAME (OUT) LRCKO (OUT) 2 (I S) LRCKO (OUT) 2 (Except I S) DOUT (OUT) 0L 0R 1L 1R 17 BCK PARAMETERS tLATE LRCKO/DOUT latency MIN TYP 3/fS MAX UNIT s Figure 10. Latency Time Between Biphase Input and LRCKO/DOUT Submit Documentation Feedback 17 DIR9001 www.ti.com SLES198 - DECEMBER 2006 The relationships among BCKO, LRCKO, and DOUT for each format are shown in Figure 11. Right Justified (MSB First, 24-bit, 16-bit) 1/fS R-channel L-channel LRCKO BCKO Data Length: 16-bit DOUT 14 15 16 1 2 MSB 1 2 15 16 LSB MSB 15 16 LSB Data Length: 24-bit DOUT 22 23 24 1 2 1 2 23 24 MSB LSB 23 24 MSB LSB Left Justified (MSB First) 1/fS R-channel L-channel LRCKO BCKO Data Length: 24-bit DOUT 23 24 1 2 MSB 23 24 1 2 LSB MSB LSB 2 I S Format (MSB First) 1/fS L-channel LRCKO R-channel BCKO Data Length: 24-bit DOUT 1 2 MSB 23 24 1 2 LSB MSB 23 24 LSB Figure 11. Decoded Serial Audio Data Output Formats 18 Submit Documentation Feedback 1 DIR9001 www.ti.com SLES198 - DECEMBER 2006 tSCY tSCBC SCKO (OUT) VDD/2 LRCKO (OUT) VDD/2 tBCH tBCL tCKLR BCKO (OUT) VDD/2 tBCY tBCDO DOUT (OUT) VDD/2 PARAMETERS MIN TYP MAX UNIT tSCY System clock pulse cycle time 18 tSCBC Delay time of SCK rising edge to BCK rising edge 4 8 15 ns ns tCKLR Delay time of BCKO falling edge to LRCKO valid -5 0.5 0.5 ns tBCY BCKO pulse cycle time tBCH BCKO pulse duration, HIGH 60 ns tBCL BCKO pulse duration, LOW 60 ns tBCDO Delay time of BCKO falling edge to DOUT valid -5 5 ns tr Rising time of all signals 10 ns tf Falling time of all signals 10 ns 1/64fS 1 s NOTE: Load capacitance of the LRCKO, BCKO, and DOUT pins is 20 pF. DOUT, LRCKO, and BCKO are synchronized with SCKO. Figure 12. Decoded Audio Data Output Timing Submit Documentation Feedback 19 DIR9001 www.ti.com SLES198 - DECEMBER 2006 Channel-Status Data and User Data Serial Outputs The DIR9001 can output channel-status data and user data synchronized with audio data from the biphase input signal. Each output data has its own dedicated output pin. * Channel-status data (C, hereinafter) is output through COUT pin. * User data (U, hereinafter) is output through UOUT pin. The C and U outputs are synchronized with LRCKO recovered from the biphase input signal. The polarity of LRCKO recovered from the biphase input signal depends on FMT[1:0] setting. For detecting the top of the block of channel-status data or user data, the BFRAME pin is provided. The BFRAME pin outputs a high level for an 8-LRCK period if the preamble B is detected in the received biphase signal. In processing these data by a microcontroller or register circuit, LRCKO is used as the data input clock, and the output pulse on the BFRAME pin is used as the top-of-block signal. The relationship among LRCKO, BFRAME, DOUT, COUT, and UOUT is shown in Figure 13. When in the XTI mode and the PLL-locked state, COUT and UOUT output L. Recovered LRCKO 2 (I S) Recovered LRCKO 2 (Except I S) 17 BCK BFRAME DOUT 191R 0L 0R 1L 1R 2L 3L 2R COUT C191R C0L C0R C1L C1R C2L C2R UOUT U191R U0L U0R U1L U1R U2L U2R NOTE: The numbers 0 through 191 of DOUT, COUT, and UOUT indicate frame numbers of the biphase input. Figure 13. LRCKO, DOUT, BFRAME, COUT, UOUT Output Timing Channel-Status Data Information Output Terminal The DIR9001 can output part of the channel-status information (bit 1, bit 3) through two dedicated pins, AUDIO and EMPH. The channel-status information which can be output from dedicated pins is limited to information from the L-channel. If channel-status information other than AUDIO or EMPH is required, or information from the R-channel, then the channel-status data on the COUT pin, which is synchronized with biphase input signal, can be used. These outputs are synchronized with the top of block. The information that can be output through the dedicated pins is shown as follows. 20 Submit Documentation Feedback DIR9001 www.ti.com SLES198 - DECEMBER 2006 AUDIO Pin This is the output pin for the audio sample word information of the channel-status data bit 1. Table 8. Audio Sample Word Information AUDIO DESCRIPTION L Audio sample word represents linear PCM samples. H Audio sample word is used for other purposes. EMPH Pin This is the output pin for the emphasis information of the channel-status data bit 3. Table 9. Pre-Emphasis Information EMPH DESCRIPTION L Two audio channels without pre-emphasis H Two audio channels with 50 s / 15 s pre-emphasis LRCKO 2 (I S) LRCKO 2 (Except I S) DOUT 191R 0L 0R 1L 1R AUDIO Bit 1 of Previous Block EMPH Bit 3 of Previous Block 2L 2R 3L NOTE: The numbers 0 through 191 of DOUT indicate frame numbers of the biphase input. Figure 14. AUDIO and EMPH Output Timing Submit Documentation Feedback 21 DIR9001 www.ti.com SLES198 - DECEMBER 2006 ERRORS AND ERROR PROCESSING Error Output Description Error detection and data error processing for PLL errors * PLL responds with unlock for data in which the rule of biphase encoding is lost (biphase error and frame-length error). * PLL responds with unlock for data in which the preamble B, M, W can not be detected. Error processing function and error output pins * The DIR9001 has a data error detect function and an error output pin, ERROR. * The ERROR pin is defined as the logical OR of data error and parity error detection. * The ERROR rising edge is synchronized with CLKST. * The ERROR falling edge is synchronized with LRCK. The relationship between data error and detected parity error is shown in Figure 15. DIR9001 Data Error Detected Parity Error ERROR Output Figure 15. ERROR Output The state of the ERROR pin and the details of error are shown in Table 10. Table 10. State of ERROR Output Pin ERROR DESCRIPTION L Lock state of PLL and nondetection of parity error H Unlock state of PLL or detection of parity error Parity Error Processing Error detection and error processing for parity errors * For PCM data, interpolation processing by previous data is performed. * For non-PCM data, interpolation is not performed and data is directly output with no processing. (Non-PCM data is data with channel-status data bit 1 = 1.) The processing for parity error occurrence is shown in Figure 16. 22 Submit Documentation Feedback DIR9001 www.ti.com SLES198 - DECEMBER 2006 [AUDIO = L] Internal LOCK AUDIO 2 LRCKO (I S) ERROR DOUT MUTE (Low) Ln Rn Ln+1 Rn+1 Ln+1 Rn+2 Ln+3 Rn+3 Interpolation Processing by Previous Data [AUDIO = H] Parity Error Internal LOCK AUDIO 2 LRCKO (I S) ERROR DOUT MUTE (Low) Ln Rn Ln+1 Rn+1 Ln+2 Rn+2 Ln+3 Rn+3 Parity Error Figure 16. Processing for Parity Error Occurrence Other Error Error for sampling frequency change: A rapid continuous change or a discontinuous change of the input sampling frequency causes the PLL to lose lock. Submit Documentation Feedback 23 DIR9001 www.ti.com SLES198 - DECEMBER 2006 CALCULATION OF ACTUAL SAMPLING FREQUENCY The DIR9001 calculates the actual sampling frequency of the biphase input signal and outputs its result through dedicated pins. To use this function, a 24.576-MHz clock source must be supplied to the XTI pin. The 24.576-MHz clock is used as a measurement reference clock to calculate the actual sampling frequency. If the XTI pin is connected to DGND, calculation of the actual sampling frequency is not performed. If there is an error in the XTI clock frequency, the calculation result and range are shifted correspondingly. This output is the result of calculating the sampling frequency, it is not the sampling frequency information of the channel-status data (bit 24-bit 27). The sampling frequency information of the channel-status data (bit 24-bit 27) is not output through these pins. The calculation result is decoded into 2-bit data, which is output on the FSOUT[1:0] pins. If the PLL is locked but the sampling frequency is out-of-range, or if the PLL is unlocked, FSOUT[1:0] = HL is output to indicate an abnormality. When the XTI source clock is not supplied before power on, FSOUT [1:0] always outputs LL. When the XTI source clock is stopped, the fS calculator holds the last value of the fS calculator result. If XTI source clock is supplied, the fS calculator resumes operation. The calculated value is held until reset. The relationship between the FSOUT[1:0] outputs and the range of sampling frequencies is shown in Table 11. Table 11. Calculated Sampling Frequency Output 24 NOMINAL fS ACTUAL SAMPLING FREQUENCY RANGE CALCULATED SAMPLING FREQUENCY OUTPUT Out of range Out of range or PLL unlocked H L 32 kHz 31.2 kHz-32.8 kHz H H 44.1 kHz 43 kHz-45.2 kHz L L 48 kHz 46.8 kHz-49.2 kHz L H FSOUT1 Submit Documentation Feedback FSOUT0 DIR9001 www.ti.com SLES198 - DECEMBER 2006 TYPICAL CIRCUIT CONNECTION Figure 17 illustrates typical circuit connection. For Automatic Clock Source Selection Actual Sampling Frequency Output 3.3-V VDD + C5 CKSEL 28 FSOUT0 ERROR 27 3 FSOUT1 FMT1 26 4 SCKO FMT0 25 5 VDD VCC 24 1 AUDIO 2 C6 + C7 6 DGND 7 X1 C4 C8 3.3-V VCC AGND 23 XTO FILT 22 8 XTI RST 21 Reset (active LOW) 9 CLKST RXIN 20 Receiver Circuit 10 LRCKO RSV 19 11 BCKO BFRAME 18 12 DOUT EMPH 17 13 PSCK0 UOUT 16 14 PSCK1 COUT 15 C2 R2 C3 Decoded Data Format Setting C1 R1 To Microcontroller System Clock Frequency Setting (128, 256, 384, 512 fS) Audio Data Processor NOTES: R1: Loop filter resistor, 680 R2: Current-limiting resistor; generally, a 100 -500 resistor is used, but it depends on the crystal resonator. C1: Loop filter capacitor, 0.068 F. C2: Loop filter capacitor, 0.0047 F. C3, C4: OSC load capacitor; generally, a 10-pF-30-pF capacitor is used, but it depends on the crystal resonator and PCB layout. C5, C8: 10-F electrolytic capacitor typical, depending on power-supply quality and PCB layout. C6, C7: 0.1-F ceramic capacitor typical, depending on power-supply quality and PCB layout. X1: Crystal resonator, use a 24.576-MHz fundamental resonator when XTI clock source is needed. Figure 17. Typical Circuit Connection Diagram Submit Documentation Feedback 25 DIR9001 www.ti.com SLES198 - DECEMBER 2006 APPLICATION INFORMATION Differences for DIR1703 The DIR9001 has many improved functions compared to the DIR1703. The DIR9001 functions are similar to those of the DIR1703. The DIR9001 pin assignment is equivalent to that of the DIR1703. The DIR9001 biphase input signal decoding function is almost equivalent to that of the DIR1703. The differences between the DIR9001 and DIR1703 are shown in Table 12. Table 12. Main Differences Between DIR1703 and DIR9001 DIFFERENCE DIR1703 DIR9001 Operational supply-voltage range 3 V to 3.6 V 2.7 V to 3.6 V Operation temperature range -25C to 85C -40C to 85C Package SSOP-28P, pin pitch: 0.65 mm TSSOP-28P, pin pitch: 0.65 mm Clock recovery architecture SpActTM feature Conventional PLL IEC60958-3 jitter tolerance Not compliant Compliant IEC60958 sampling frequency accuracy Level II (1000 ppm) Level III (12.5%) Acceptable sampling frequency 32/44.1/48/88.2/96 kHz, 1500 ppm 28 kHz to 108 kHz continuous Biphase input signal level CMOS level 5-V tolerant TTL level Connection of loop filter Between FILT pin and VCC Between FILT pin and AGND XTI source clock frequency One of the following clock sources or resonators must be connected to the XTI pin: 4.069/5.6448/6.144/ 8.192/11.2896/12.288/ 16.384/16.9344/18.432/ 22.5792/24.576-MHz Optional 24.576-MHz (24.576-MHz clock is only required to use the internal actual-sampling-frequency calculator or use the DIR9001 as a 24.576-MHz clock generator.) BFRAME H period 32/fS 8/fS Channel status and user data Synchronous with LRCK transition 17-BCK delay from LRCK transition Latest tracked frequency hold Available Not available PLL mode clock at error Latest tracked frequency VCO free-running frequency Clock transition signal out CKTRNS pin, active H CLKST pin, active-high Oscillation amplifier External feedback resistor (typ. 1 M) Internal feedback resistor 26 Submit Documentation Feedback DIR9001 www.ti.com SLES198 - DECEMBER 2006 The differences between the DIR1703 and DIR9001 I/O pins are shown in Table 13. Table 13. The Differences Between DIR1703 and DIR9001 in All I/O Pin PIN NO. DIR1703 DIR9001 DIFFERENCES 1 ADFLG AUDIO Pin name only Channel-status data information of non-audio sample word, active-low DESCRIPTIONS OF DIR9001 2 BRATE0 FSOUT0 Pin name only Actual-sampling-frequency calculated result output 0 3 BRATE1 FSOUT1 Pin name only Actual-sampling-frequency calculated result output 1 4 SCKO SCKO Same function System clock output 5 VDD VDD Same function Digital power supply, 3.3-V 6 DGND DGND Same function Digital ground 7 XTO XTO Same function Oscillation amplifier output 8 XTI XTI Same function Oscillation amplifier input, or external XTI source clock input 9 CKTRNS CLKST CLKST is active-high 10 LRCKO LRCKO Same function Clock change/transition signal output Audio data latch enable output 11 BCKO BCKO Same function Audio data bit clock output 12 DOUT DOUT Same function 16 bit-24 bit decoded serial digital audio data output 13 SCF0 PSCK0 Pin name only SCKO output frequency selection 0 14 SCF1 PSCK1 Pin name only SCKO output frequency selection 1 15 CSBIT COUT Pin name only Channel-status data serial output synchronized with LRCKO 16 URBIT UOUT Pin name only User data serial output synchronized with LRCKO 17 EMFLG EMPH Pin name only Channel-status data Information of pre-emphasis (50 s/15 s) 18 BFRAME BFRAME Same function Indication of top block of biphase input signal 19 BRSEL RSV Reserved 20 DIN RXIN Pin name only Biphase digital data input 21 RST RST Same function Reset control input, active-low 22 FILT FILT Same function External filter connection terminal. Recommended filter must be connected. 23 AGND AGND Same function Analog ground 24 VCC VCC Same function Analog power supply, 3.3-V 25 FMT0 FMT0 Same function Decoded serial digital audio data output format selection 0 26 FMT1 FMT1 Same function Decoded serial digital audio data output format selection 1 27 UNLOCK ERROR Pin name only Indication of internal PLL or data parity error 28 CKSEL CKSEL Same function Selection of system clock source, Low: PLL (VCO) clock, High: XTI clock Reserved, must be connected to DGND Submit Documentation Feedback 27 PACKAGE OPTION ADDENDUM www.ti.com 3-Apr-2009 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty DIR9001PW ACTIVE TSSOP PW 28 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM DIR9001PWG4 ACTIVE TSSOP PW 28 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM DIR9001PWR ACTIVE TSSOP PW 28 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM DIR9001PWRG4 ACTIVE TSSOP PW 28 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF DIR9001 : * Automotive: DIR9001-Q1 NOTE: Qualified Version Definitions: * Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device DIR9001PWR Package Package Pins Type Drawing TSSOP PW 28 SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 2000 330.0 16.4 Pack Materials-Page 1 6.9 B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 10.2 1.8 12.0 16.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) DIR9001PWR TSSOP PW 28 2000 367.0 367.0 38.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated