TANTALUM DIPPED / RADIAL — POLAR
Tantalum Dipped /
Radial — Polar
KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606 (864) 963-6300 61
•CAPACITANCE/VOLTAGE RANGE:
T35X/T39X: 0.1-680µF, 3-50 Volts.
T36X: 0.1-330µF, 6-50 Volts.
•CAPACITANCE TOLERANCE: Available in stan-
dard EIA nominal values with ±20% and ±10%
standard.
•DISSIPATION FACTOR: Maximum DF limits are
shown in corresponding series part number list-
ings. See Application Notes Section, page 76 for
additional information.
•DC LEAKAGE CURRENT: Maximum leakage val-
ues at 25°are shown in part number listings,
pages 63-65, 67, 68 and 70. See Application
Notes Section, pages 76 & 77 for additional infor-
mation.
•
RATED VOLTAGE; WORKING VOLTAGE; SURGE
VOLTAGE; REVERSE VOLTAGE: See Application
Notes Section, pages 76 & 77 for description.
•IMPEDANCE and ESR: See Application Notes
Section, page 77 & 78 for description. Reference
ESR values are shown in table below.
•AC RIPPLE VOLTAGE: Permissible AC ripple volt-
age is related to equivalent series resistance
(ESR) and power dissipation capability. Maximum
power dissipation for each case size is listed in
Table below. For additional description see page
78.
•ENVIRONMENTAL CONSIDERATIONS:
A. Shock Test: MIL-STD-202, Method 213.
B. Thermal Shock, MIL-STD-202, Method 107,
Condition A.
C.Moisture Resistance: MIL-STD-202,
Method 106.
D.Solderability: MIL-STD-202, Method 208.
For additional Environmental Test Information
see pages 80, 81 and 82.
• LEAD MATERIAL: Effective June 30, 2005 the
T35x, T368 and T39x Series will be available, as an
PERFORMANCE CHARACTERISTICS
Case Power Dissipation
Size (max.) @ 25°C (watts)
T35X, A .040
T39X B .050
C .060
D .065
E .070
F .080
G .090
H .100
J.110
K .120
L .130
M .140
T36X A .050
B .075
C .090
D .135
Maximum Power Dissipation Capability @ 25°C
Commercial T35X/T36X/T39X ESR (OHMS) at 100 kHz @ +25°C
(The ESR values provided below are for reference only. No warranty, as
stated on page 3 and reincorporated here, is made as to the accuracy
of these values for any particular T35X, T36X, T39X Series product.)
0.10
0.15
0.22
0.33
0.47
0.68
1.00
1.50
2.20
3.30
4.70
6.80
10.0
15.0
22.0
33.0
47.0
68.0
100.0
150.0
220.0
330.0
13.0
10.0
8.0
6.0
5.0
3.7
3.0
2.0
1.8
1.6
0.9
0.9
0.7
13.0
10.0
8.0
6.0
5.0
3.7
2.7
2.1
1.7
1.3
1.0
0.8
0.6
10.0
8.0
6.0
5.0
4.0
3.2
2.5
2.0
1.6
1.3
1.0
0.8
0.6
10.0
9.0
7.0
5.5
4.5
3.6
2.9
2.3
1.8
1.4
1.2
0.9
0.6
10.0
8.0
6.0
5.0
4.0
3.1
2.5
2.0
1.5
1.2
1.0
0.8
26.0
21.0
17.0
15.0
13.0
10.0
8.0
6.0
5.0
4.0
3.0
2.5
2.0
1.6
1.3
1.0
0.8
26.0
21.0
17.0
15.0
13.0
10.0
8.0
5.0
3.5
3.0
2.5
2.0
1.6
1.2
1.0
Cap.
µF6
Volt 10
Volt 16
Volt 20
Volt 25
Volt 35
Volt 50
Volt
• LEAD TAPE AND REEL: Reeling per specification
RS-468. See pages 72 - 74 for additional information.
option, with 100% Matte Tin (RoHS compliant) lead wire
or Sn/Pb lead wire. Please see page 63 for part number
ordering information. The T363 and T369 lead mater-
ial will remain Sn/Pb solder coated steel core with a
copper ply per MIL-STD-127 and at this time will not
be available with a 100% Sn option.
TANTALUM DIPPED / RADIAL - POLAR
T350, T351, T352, T353, T354, T355 & T356 SERIES “ULTRADIP II”
62 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606 (864) 963-6300
The KEMET ‘UltraDip II’Capacitors offer the designer of quality
instruments and entertainment systems the widely recognized
advantages inherent in solid tantalum capacitors at competitive
prices.
The ‘UltraDip II’Series, miniature dipped solid tantalum capacitors,
provide the designer with the advantage of compactness plus low
leakage and low DF performance characteristics for filtering,
bypassing, coupling, blocking and RC timing circuits. This series fea-
tures a capacitance range from 0.1 to 680 microfarads at voltages
from 3 to 50 VDC. ‘UltraDip II’capacitors utilize the same sophisti-
cated materials and processes which have advanced KEMET
Electronics Corporation to the leadership position in solid tantalum
capacitors.
The plastic case provides a tough barrier coating and maintains pre-
cision of lead wire spacing within ±0.015 inch. The gold color epoxy
utilized permits Laser marking with outstanding permanency and
legibility. All case sizes are printed with capacitance, voltage, polar-
ity and vendor identification.
Solid tantalum devices exhibit no degradation failure mode during
shelf storage and show a constantly decreasing failure rate (i.e.,
absence of wearout mechanism) during life tests.
The ‘UltraDip II’Series provides self-insulating cases which are
resistant to shock and vibration. These capacitors exhibit low DCL,
ESR and Impedance and have excellent temperature stability.
CAPACITOR OUTLINE DRAWINGS
.50±.05
Lead Spacing
See Note 2
Max.
DMax.
D
H
Max.
**.02
(0.5)
.10
(2.54)
H
Max.
HMax.
H
Max.
D
.02
(0.5)
.02
(0.5) .02
(0.5)
.187±.032
(4.75±.81)
Max.
D
.187±.032
(4.75±.81)
.20
(5.08)
.20
(5.08) .250
(6.35)
Max.
HMax.
H
.187±.032
(4.75±.81)
.250±.025
(6.35±.64)
Max.
DMax.
DMax.
D
Max.
H
.187±.032
(4.75±.81)
Max.
H
.187±.032
(4.75±.81)
Max.
H
.187±.032
(4.75±.81)
.125
(3.18) .20
(5.08)
*Lead Tolerance = ± .015 (± .38 mm) ** All Lead Diameters = .02 ± .002 (0.5 ± .05 mm)
T350 T351 T353 T354 T355 T356T352
DIMENSIONS — INCHES (MILLIMETERS)
All T350 T351 T352 T353 T354 T355 T356
Case D H(1) H(1) H(1) H(1) H(1) H(1) H(1)
Size Max Diameter Max Height Max Height Max Height Max Height Max Height Max Height Max Height
A .175 (4.5) .280 (7.1) .380 (9.6) .400 (10.2) .400 (10.2) .340 (8.6) .340 (8.6) .340 (8.6)
B .175 (4.5) .300 (7.6) .390 (9.9) .410 (10.4) .410 (10.4) .350 (8.9) .350 (8.9) .350 (8.9)
C .196 (5.0) .330 (8.4) .420 (10.7) .440 (11.2) .440 (11.2) .380 (9.6) .380 (9.6) .380 (9.6)
D .196 (5.0) .340 (8.6) .430 (10.9) .450 (11.4) .450 (11.4) .390 (9.9) .390 (9.9) .390 (9.9)
E .216 (5.5) .350 (8.9) .440 (11.2) .460 (11.7) .460 (11.7) .400 (10.2) .400 (10.2) .400 (10.2)
F .236 (6.0) .390 (9.9) .480 (12.2) .500 (12.7) .500 (12.7) .440 (11.2) .440 (11.2) .440 (11.2)
G .250 (6.3) .400 (10.2) .490 (12.4) .510 (13.0) .510 (13.0) .450 (11.4) .450 (11.4) .450 (11.4)
H .300 (7.6) .400 (10.2) .500 (12.7) .520 (13.2) .520 (13.2) .470 (11.9) .470 (11.9) .470 (11.9)
J(2) .330 (8.4) .500 (12.7) .580 (14.7) .550 (14.0) .550 (14.0)
K(2) .350 (8.9) .530 (13.5) .630 (16.0) .610 (15.5) .610 (15.5)
L(2) .350 (8.9) .630 (16.0) Note 3 Note 3 .730 (18.5) .710 (18.1) Note 3 .710 (18.1)
M(2) .400 (10.2) .670 (17.0) .760 (19.3) .740 (18.8) .740 (18.8)
NOTES: (1) All “H” Dimensions are from Capacitor seating plane to top of Capacitor.
(2) On T350 Series, case sizes A-H are supplied with .100”(2.54) lead spacing—case sizes J-M are supplied with .200”(5.08) lead spacing.
(3) These case sizes are not available for T351, T352 & T355 capacitors.
LEAD CONFIGURATION & SPACING CHART
LEAD SERIES
CASE CONFIGURATION T350 T351 T352 T353 T354 T355 T356
.100 X X
.125 X
.200 X X X
.250 X
A-H STRAIGHT LEAD X
STAND OFF X X X X X
SNAP-IN X
.100
.125
.200 X X X
.250 X
J-M STRAIGHT LEAD X
STAND OFF X X
SNAP-IN X
“NOT AVAILABLE”
“NOT AVAILABLE”
“NOT AVAILABLE”
T350 T351 T353 T354 T355 T356T352
Effective June 30, 2005 the T35x Series is RoHS compliant.
MAX.
DISSI-
PATION
CAPAC- D.C. FACTOR
ITANCE CASE LEAKAGE %@25°C,
µF SIZE KEMET PART NUMBER µA@25°C 120Hz
3 VOLT RATING AT 85°C —
2 VOLT RATING AT 125°C
4.7 A T35(1)A475(3)003A(4) 0.5 5
5.6 A T35(1)A565(3)003A(4) 0.5 5
6.8 A T35(1)A685(3)003A(4) 0.5 5
8.2 A T35(1)A825(3)003A(4) 0.5 6
10.0 A T35(1)A106(3)003A(4) 0.5 6
12.0 B T35(1)B126(3)003A(4) 0.5 6
15.0 B T35(1)B156(3)003A(4) 0.5 6
18.0 C T35(1)C186(3)003A(4) 0.5 6
22.0 C T35(1)C226(3)003A(4) 0.5 6
27.0 D T35(1)D276(3)003A(4) 0.6 6
33.0 D T35(1)D336(3)003A(4) 0.8 6
39.0 E T35(1)E396(3)003A(4) 0.9 6
47.0 E T35(1)E476(3)003A(4) 1.1 6
56.0 F T35(1)F566(3)003A(4) 1.3 6
68.0 F T35(1)F686(3)003A(4) 1.6 6
82.0 G T35(1)G826(3)003A(4) 2.0 8
100.0 G T35(1)G107(3)003A(4) 2.4 8
120.0 H T35(1)H127(3)003A(4) 2.9 8
150.0 H T35(1)H157(3)003A(4) 3.6 8
180.0 J T35(2)J187(3)003A(4) 4.3 8
220.0 J T35(2)J227(3)003A(4) 5.3 8
270.0 K T35(2)K277(3)003A(4) 6.5 8
330.0 K T35(2)K337(3)003A(4) 7.9 8
390.0 L T35(2)L397(3)003A(4) 9.4 9
470.0 L T35(2)L477(3)003A(4) 10.0 9
560.0 M T35(2)M567(3)003A(4) 10.0 9
680.0 M T35(2)M687(3)003A(4) 10.0 9
TANTALUM DIPPED / RADIAL - POLAR
T350, T351, T352, T353, T354, T355 & T356 SERIES “ULTRADIP II”
T35X Series
Tantalum Dipped / Radial
KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606 (864) 963-6300 63
T35X
RATINGS AND PART NUMBER REFERENCE
(1) To complete KEMET Part Number, insert Series Designation as follows: “0” = T350, “1” = T351, “2” = T352, “3” = T353, “4” = T354, “5” = T355, “6” = T356.
(2) To complete KEMET Part Number, insert only Series Designation as follows: “0” = T350, “3” = T353, “4” = T354, “6” = T356.
(3) To complete KEMET Part Number, insert Capacitance Tolerance Symbol: “M” = ±20%, “K” = ±10%.
(4) To complete KEMET Part Number, insert Lead Material designation : S = SnPb (tin/lead) and T = 100% Sn (tin).
NOTE: Higher voltage and better capacitance tolerance product may be substituted for an order within the same case size at KEMET’s option.
T35X & T36X
ORDERING INFORMATION
T 3XX A 105 M 035 A S*
TANTALUM
SERIES
Insert appropriate number to
replace letter “X” — 350, 351, 352,
353, 354, 355, 356, 363, 368, or 369.
CASE SIZE
A, B, C, D, E, F, G, H, J, K, L & M
PICOFARAD CODE
First two digits are significant
figures. Third figure is the
number of zeros following.
LEAD MATERIAL
S — Sn/Pb (tin/lead)
FAILURE RATE LEVEL
A— Not Applicable
VOLTAGE RATING
For 6.3 Volts use 006
CAPACITANCE TOLERANCE
M — ±20%
K — ±10%
J — ±5% Available on special order.
*T363 & T369 capacitors
available only with M & K tolerances
T35X & T368
MARKING INFORMATION
MAX.
DISSI-
PATION
CAPAC- D.C. FACTOR
ITANCE CASE LEAKAGE %@25°C,
µF SIZE KEMET PART NUMBER µA@25°C 120Hz
6.3 VOLT RATING AT 85°C —
4 VOLT RATING AT 125°C
3.3 A T35(1)A335(3)006A(4) 0.5 5
3.9 A T35(1)A395(3)006A(4) 0.5 5
4.7 A T35(1)A475(3)006A(4) 0.5 5
5.6 A T35(1)A565(3)006A(4) 0.5 5
6.8 A T35(1)A685(3)006A(4) 0.5 5
8.2 B T35(1)B825(3)006A(4) 0.5 6
10.0 B T35(1)B106(3)006A(4) 0.5 6
12.0 C T35(1)C126(3)006A(4) 0.6 6
15.0 C T35(1)C156(3)006A(4) 0.7 6
18.0 D T35(1)D186(3)006A(4) 0.9 6
22.0 D T35(1)D226(3)006A(4) 1.1 6
27.0 E T35(1)E276(3)006A(4) 1.3 6
33.0 E T35(1)E336(3)006A(4) 1.6 6
39.0 F T35(1)F396(3)006A(4) 1.9 6
47.0 F T35(1)F476(3)006A(4) 2.3 6
56.0 G T35(1)G566(3)006A(4) 2.7 6
68.0 G T35(1)G686(3)006A(4) 3.3 6
82.0 H T35(1)H826(3)006A(4) 3.9 8
100.0 H T35(1)H107(3)006A(4) 4.8 8
120.0 J T35(2)J127(3)006A(4) 5.8 8
150.0 J T35(2)J157(3)006A(4) 7.2 8
180.0 K T35(2)K187(3)006A(4) 8.6 8
220.0 K T35(2)K227(3)006A(4) 10.0 8
270.0 L T35(2)L277(3)006A(4) 10.0 8
330.0 L T35(2)L337(3)006A(4) 10.0 8
Polarity
Date
Code
Capacitance
(pF code)
KEMET
Trademark
335
35K
Polarity
Stripe (+)
+
418
Voltage
Rating
*Part Number Example: T350A105M035AS (14 digits – no spaces)
T – 100% Sn (tin)
MAX.
DISSI-
PATION
CAPAC- D.C. FACTOR
ITANCE CASE LEAKAGE %@25°C,
µF SIZE KEMET PART NUMBER µA@25°C 120Hz
20 VOLT RATING AT 85°C —
13 VOLT RATING AT 125°C
1.0 A T35(1)A105(3)020A(4) 0.5 5 0.5 3
1.2 A T35(1)A125(3)020A(4) 0.5 5
1.5 A T35(1)A155(3)020A(4) 0.5 5
1.8 A T35(1)A185(3)020A(4) 0.5 5
2.2 A T35(1)A225(3)020A(4) 0.5 5
2.7 B T35(1)B275(3)020A(4) 0.5 5
3.3 B T35(1)B335(3)020A(4) 0.5 5
3.9 C T35(1)C395(3)020A(4) 0.6 5
4.7 C T35(1)C475(3)020A(4) 0.8 5
5.6 D T35(1)D565(3)020A(4) 0.9 5
6.8 D T35(1)D685(3)020A(4) 1.1 5
8.2 E T35(1)E825(3)020A(4) 1.3 6
10.0 E T35(1)E106(3)020A(4) 1.6 6
12.0 F T35(1)F126(3)020A(4) 1.9 6 1.9 6
15.0 F T35(1)F156(3)020A(4) 2.4 6
18.0 G T35(1)G186(3)020A(4) 2.9 6
22.0 G T35(1)G226(3)020A(4) 3.5 6
27.0 J T35(2)J276(3)020A(4) 4.3 6
33.0 J T35(2)J336(3)020A(4) 5.3 6
39.0 K T35(2)K396(3)020A(4) 6.2 6
47.0 K T35(2)K476(3)020A(4) 7.5 6
56.0 L T35(2)L566(3)020A(4) 9.0 6
68.0 L T35(2)L686(3)020A(4) 10.0 6
82.0 M T35(2)M826(3)020A(4) 10.0 8
100.0 M T35(2)M107(3)020A(4) 10.0 8
25 VOLT RATING AT 85°C —
16.5 VOLT RATING AT 125°C
1.0 A T35(1)A105(3)025A(4) 0.5 5
1.2 A T35(1)A125(3)025A(4) 0.5 5
1.5 A T35(1)A155(3)025A(4) 0.5 5
1.8 A T35(1)A185(3)025A(4) 0.5 5
2.2 B T35(1)B225(3)025A(4) 0.5 5
2.7 B T35(1)B275(3)025A(4) 0.5 5
3.3 B T35(1)B335(3)025A(4) 0.7 5
3.9 C T35(1)C395(3)025A(4) 0.8 5
4.7 C T35(1)C475(3)025A(4) 0.9 5
5.6 E T35(1)E565(3)025A(4) 1.1 5
6.8 E T35(1)E685(3)025A(4) 1.4 5
8.2 E T35(1)E825(3)025A(4) 1.6 6
10.0 E T35(1)E106(3)025A(4) 2.0 6
12.0 G T35(1)G126(3)025A(4) 2.4 6
15.0 G T35(1)G156(3)025A(4) 3.0 6
18.0 H T35(1)H186(3)025A(4) 3.6 6
22.0 H T35(1)H226(3)025A(4) 4.4 6
27.0 J T35(2)J276(3)025A(4) 5.4 6
33.0 J T35(2)J336(3)025A(4) 6.6 6
39.0 K T35(2)K396(3)025A(4) 7.8 6
47.0 K T35(2)K476(3)025A(4) 9.4 6
56.0 L T35(2)L566(3)025A(4) 10.0 6
68.0 L T35(2)L686(3)025A(4) 10.0 6
MAX.
DISSI-
PATION
CAPAC- D.C. FACTOR
ITANCE CASE LEAKAGE %@25°C,
µF SIZE KEMET PART NUMBER µA@25°C 120Hz
10 VOLT RATING AT 85°C —
7 VOLT RATING AT 125°C
2.2 A T35(1)A225(3)010A(4) 0.5 5
2.7 A T35(1)A275(3)010A(4) 0.5 5
3.3 A T35(1)A335(3)010A(4) 0.5 5
3.9 A T35(1)A395(3)010A(4) 0.5 5
4.7AT35(1)A475(3)010A(4) 0.5 5
5.6 B T35(1)B565(3)010A(4) 0.5 5
6.8 B T35(1)B685(3)010A(4) 0.5 5
8.2 C T35(1)C825(3)010A(4) 0.7 6
10.0 C T35(1)C106(3)010A(4) 0.8 6
12.0 E T35(1)E126(3)010A(4) 1.0 6
15.0 E T35(1)E156(3)010A(4) 1.2 6
18.0 E T35(1)E186(3)010A(4) 1.4 6
22.0 E T35(1)E226(3)010A(4) 1.8 6
27.0 F T35(1)F276(3)010A(4) 2.2 6
33.0 F T35(1)F336(3)010A(4) 2.6 6
39.0 G T35(1)G396(3)010A(4) 3.1 6
47.0 H T35(1)H476(3)010A(4) 3.8 6
56.0 H T35(1)H566(3)010A(4) 4.5 6
68.0 H T35(1)H686(3)010A(4) 5.4 6
82.0 J T35(2)J826(3)010A(4) 6.6 8
100.0 J T35(2)J107(3)010A(4) 8.0 8
120.0 K T35(2)K127(3)010A(4) 9.6 8
150.0 K T35(2)K157(3)010A(4) 10.0 8
180.0 L T35(2)L187(3)010A(4) 10.0 8
220.0 L T35(2)L227(3)010A(4) 10.0 8
16 VOLT RATING AT 85°C —
10 VOLT RATING AT 125°C
1.5 A T35(1)A155(3)016A(4) 0.5 5
1.8 A T35(1)A185(3)016A(4) 0.5 5
2.2 A T35(1)A225(3)016A(4) 0.5 5
2.7 A T35(1)A275(3)016A(4) 0.5 5
3.3 A T35(1)A335(3)016A(4) 0.5 5
3.9 B T35(1)B395(3)016A(4) 0.5 5
4.7 B T35(1)B475(3)016A(4) 0.6 5
5.6 C T35(1)C565(3)016A(4) 0.7 5
6.8 C T35(1)C685(3)016A(4) 0.9 5
8.2 E T35(1)E825(3)016A(4) 1.0 6
10.0 E T35(1)E106(3)016A(4) 1.3 6
12.0 E T35(1)E126(3)016A(4) 1.5 6
15.0 E T35(1)E156(3)016A(4) 1.8 6
18.0 F T35(1)F186(3)016A(4) 2.2 6
22.0 F T35(1)F226(3)016A(4) 2.6 6
27.0 H T35(1)H276(3)016A(4) 3.2 6
33.0 H T35(1)H336(3)016A(4) 4.0 6
39.0 J T35(2)J396(3)016A(4) 4.7 6
47.0 J T35(2)J476(3)016A(4) 5.6 6
56.0 K T35(2)K566(3)016A(4) 6.8 6
68.0 K T35(2)K686(3)016A(4) 8.2 6
82.0 L T35(2)L826(3)016A(4) 9.8 8
100.0 L T35(2)L107(3)016A(4) 10.0 8
120.0 M T35(2)M127(3)016A(4) 10.0 8
150.0 M T35(2)M157(3)016A(4) 10.0 8
TANTALUM DIPPED / RADIAL — POLAR
T350, T351, T352, T353, T354, T355 & T356 SERIES “ULTRADIP II”
64 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606 (864) 963-6300
T35X
RATINGS AND PART NUMBER REFERENCE
(1) To complete KEMET Part Number, insert Series Designation as follows: “0” = T350, “1” = T351, “2” = T352, “3” = T353, “4” = T354, “5” = T355, “6” = T356.
(2) To complete KEMET Part Number, insert only Series Designation as follows: “0” = T350, “3” = T353, “4” = T354, “6” = T356.
(3) To complete KEMET Part Number, insert Capacitance Tolerance Symbol: “M” = ±20%, “K” = ±10%.
(4) To complete KEMET Part Number, insert Lead Material Designation as follows: S = Sn/Pb (tin/lead) and T = 100% Sn (tin).
NOTE: Higher voltage and better capacitance tolerance product may be substituted for an order within the same case size at KEMET’s option.
MAX.
DISSI-
PATION
CAPAC- D.C. FACTOR
ITANCE CASE LEAKAGE %@25°C,
µF SIZE KEMET PART NUMBER µA@25°C 120Hz
35 VOLT RATING AT 85°C —
23 VOLT RATING AT 125°C
0.10 A T35(1)A104(3)035A(4) 0.5 3
0.12 A T35(1)A124(3)035A(4) 0.5 3
0.15 A T35(1)A154(3)035A(4) 0.5 3
0.18 A T35(1)A184(3)035A(4) 0.5 3
0.22 A T35(1)A224(3)035A(4) 0.5 3
0.27 A T35(1)A274(3)035A(4) 0.5 3
0.33 A T35(1)A334(3)035A(4) 0.5 3
0.39 A T35(1)A394(3)035A(4) 0.5 3
0.47 A T35(1)A474(3)035A(4) 0.5 3
0.56 A T35(1)A564(3)035A(4) 0.5 3
0.68 A T35(1)A684(3)035A(4) 0.5 3
0.82 A T35(1)A824(3)035A(4) 0.5 3
1.0 A T35(1)A105(3)035A(4) 0.5 3
1.2 B T35(1)B125(3)035A(4) 0.5 5
1.5 B T35(1)B155(3)035A(4) 0.5 5
1.8 C T35(1)C185(3)035A(4) 0.5 5
2.2 C T35(1)C225(3)035A(4) 0.6 5
2.7 D T35(1)D275(3)035A(4) 0.7 5
3.3 D T35(1)D335(3)035A(4) 0.9 5
3.9 E T35(1)E395(3)035A(4) 1.0 5
4.7 E T35(1)E475(3)035A(4) 1.3 5
5.6 F T35(1)F565(3)035A(4) 1.6 5
6.8 F T35(1)F685(3)035A(4) 1.9 5
8.2 G T35(1)G825(3)035A(4) 2.3 6
10.0 G T35(1)G106(3)035A(4) 2.8 6
12.0 J T35(2)J126(3)035A(4) 3.4 6
15.0 J T35(2)J156(3)035A(4) 4.2 6
18.0 K T35(2)K186(3)035A(4) 5.0 6
22.0 K T35(2)K226(3)035A(4) 6.2 6
27.0 L T35(2)L276(3)035A(4) 7.6 6
33.0 L T35(2)L336(3)035A(4) 9.2 6
39.0 M T35(2)M396(3)035A(4) 10.0 6
47.0 M T35(2)M476(3)035A(4) 10.0 6
TANTALUM DIPPED / RADIAL - POLAR
T350, T351, T352, T353, T354, T355 & T356 SERIES “ULTRADIP II”
T35X Series
Tantalum Dipped / Radial
KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606 (864) 963-6300 65
T35X
RATINGS AND PART NUMBER REFERENCE
(1) To complete KEMET Part Number, insert Series Designation as follows: “0” = T350, “1” = T351, “2” = T352, “3” = T353, “4” = T354, “5” = T355, “6” = T356.
(2) To complete KEMET Part Number, insert only Series Designation as follows: “0” = T350, “3” = T353, “4” = T354, “6” = T356.
(3) To complete KEMET Part Number, insert Capacitance Tolerance Symbol: “M” = ±20%, “K” = ±10%.
(4) To complete KEMET Part Number, insert Lead Material Designation as follows: S = Sn/Pb (tin/lead) and T = 100% Tin.
Note: Higher voltage and better capacitance tolerance product may be substituted for an order within the same case size at KEMET's option.
MAX.
DISSI-
PATION
CAPAC- D.C. FACTOR
ITANCE CASE LEAKAGE %@25°C,
µF SIZE KEMET PART NUMBER µA@25°C 120Hz
50 VOLT RATING AT 85°C —
33 VOLT RATING AT 125°C
0.10 A T35(1)A104(3)050A(4) 0.5 3
0.12 A T35(1)A124(3)050A(4) 0.5 3
0.15 A T35(1)A154(3)050A(4) 0.5 3
0.18 A T35(1)A184(3)050A(4) 0.5 3
0.22 A T35(1)A224(3)050A(4) 0.5 3
0.27 A T35(1)A274(3)050A(4) 0.5 3
0.33 A T35(1)A334(3)050A(4) 0.5 3
0.39 B T35(1)B394(3)050A(4) 0.5 3
0.47 B T35(1)B474(3)050A(4) 0.5 3
0.56 B T35(1)B564(3)050A(4) 0.5 3
0.68 B T35(1)B684(3)050A(4) 0.5 3
0.82 B T35(1)B824(3)050A(4) 0.5 3
1.0BT35(1)B105(3)050A(4) 0.5 3
1.2 D T35(1)D125(3)050A(4) 0.5 5
1.5 E T35(1)E155(3)050A(4) 0.6 5
1.8 E T35(1)E185(3)050A(4) 0.7 5
2.2 E T35(1)E225(3)050A(4) 0.9 5
2.7 F T35(1)F275(3)050A(4) 1.1 5
3.3 F T35(1)F335(3)050A(4) 1.3 5
3.9 G T35(1)G395(3)050A(4) 1.6 5
4.7 G T35(1)G475(3)050A(4) 1.9 5
5.6 H T35(1)H565(3)050A(4) 2.2 5
6.8JT35(2)J685(3)050A(4) 2.75
8.2 J T35(2)J825(3)050A(4) 3.3 6
10.0KT35(2)K106(3)050A(4) 4.06
12.0 K T35(2)K126(3)050A(4) 4.8 6
15.0 L T35(2)L156(3)050A(4) 6.0 6
18.0 L T35(2)L186(3)050A(4) 7.2 6
22.0 M T35(2)M226(3)050A(4) 8.8 6
TANTALUM DIPPED / RADIAL — MIL-PRF-49137/2
T363 (CX02), T369 (CX12) SERIES
66 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606 (864) 963-6300
Product manufactured to the requirements of MIL-PRF-49137
satisfy all the performance characteristics of the UltraDip II. The
performance characteristics meet or exceed the requirements of
MIL-PRF-49137.
In addition to the standard process testing done on the UltraDip II,
all product supplied to MIL-PRF-49137 is sampled on a lot by lot
basis for Group A and Group B inspection to insure compliance.
Product supplied per MIL-PRF-49137 also receives an additional
post process burn-in for at least two (2) hours under accelerated
voltage stress in excess of 125% of DC rated voltage. This post
process burn-in is equivalent to 200 hours under rated conditions.
CAPACITOR OUTLINE DRAWINGS DIMENSIONS — INCHES & (MILLIMETERS)
MIL-PRF-49137 MARKING INFORMATION
MIL-PRF-49137/2 ORDERING INFORMATION
CX 02 D 225 K
TYPE
Capacitors, Fixed, Solid Tantalum
Conformal Coated, Non-hermetically Sealed.
STYLE
02 (T363) A, B, C & D Cases
12 (T369) A & B Cases Only
VOLTAGE
CAPACITANCE TOLERANCE
CAPACITANCE IN PICORARAD CODE
The nominal capacitance value, expressed in
picofarads (pF), is identified by a three-digit number;
the first two digits represent significant figures and
the last digit specifies the number of zeros to follow.
Symbol Capacitance Tolerance
Percent (±)
K10
M20
CASE D MAX H MAX
SIZE
A0.175 0.350
(4.45) (8.89)
B0.250 0.450
(6.35) (11.43)
C0.350 0.610
(8.89) (15.49)
D0.400 0.740
(10.16) (18.80)
T363 A-D CASE
T369 A&B CASE ONLY
*For KEMET Ordering Information, see page 63.
.187 ± .032
(4.75 ± .81)
T363 (CX02)
A, B, C & D CASES
A & B
.020 ± .002
(.51 ± .05)
C & D
.025 ± .002
(.64 ± .05)
H
MAX.
.250 ± .015
(6.35 ± .38)
D
MAX. D
MAX.
T369 (CX12)
A & B CASES
.250 ± .025
(6.35 ± .64)
H
MAX.
.125 ± .015
(3.18 ± .38)
.020 ± .002
(.51 ± .05) .187 ± .032
(4.75 ± .81)
685K
+35K
Mfg. -
KEMET
Voltage
Polarity
Capacitance Tolerance
Capacitance
(in Picofarad Code)
407
Date
Code
Symbol Rated (857C) Surge (857C)
Volts, dc Volts, dc
D6 8
F10 13
H15 20
J20 26
K25 32
M35 46
N50 65
MAX.
DISSIPATION CXO2 CX12
CAPACITANCE T363, T369 D.C. FACTOR (T363) (T369)
CAPACITANCE CASE TOLERANCE KEMET LEAKAGE %@25°C, MILITARY MILITARY
µF SIZE ±% PART NUMBER µA@25°C 120Hz PART NUMBER PART NUMBER
6 VOLT RATING AT 85°C
6.8 A 10, 20 T36(1)A685(2)006AS 0.5 6 CX02D685(2) CX12D685(2)
47.0 B 10, 20 T36(1)B476(2)006AS 2.3 6 CX02D476(2) CX12D476(2)
68.0 B 10, 20 T36(1)B686(2)006AS 3.3 6 CX02D686(2) CX12D686(2)
150.0 C 10, 20 T363C157(2)006AS 7.2 8 CX02D157(2)
330.0 D 10, 20 T363D337(2)006AS 10.0 8 CX02D337(2)
10 VOLT RATING AT 85°C
4.7 A 10, 20 T36(1)A475(2)010AS 0.5 5 CX02F475(2) CX12F475(2)
33.0 B 10, 20 T36(1)B336(2)010AS 2.6 6 CX02F336(2) CX12F336(2)
100.0 C 10, 20 T363C107(2)010AS 8.0 8 CX02F107(2)
220.0 D 10, 20 T363D227(2)010AS 10.0 8 CX02F227(2)
15 VOLT RATING AT 85°C
3.3 A 10, 20 T36(1)A335(2)015AS 0.5 5 CX02H335(2) CX12H335(2)
22.0 B 10, 20 T36(1)B226(2)015AS 2.6 6 CX02H226(2) CX12H226(2)
68.0 C 10, 20 T363C686(2)015AS 8.2 6 CX02H686(2)
150.0 D 10, 20 T363D157(2)015AS 10.0 8 CX02H157(2)
20 VOLT RATING AT 85°C
2.2 A 10, 20 T36(1)A225(2)020AS 0.5 5 CX02J225(2) CX12J225(2)
15.0 B 10, 20 T36(1)B156(2)020AS 2.4 6 CX02J156(2) CX12J156(2)
47.0 C 10, 20 T363C476(2)020AS 7.5 6 CX02J476(2)
100.0 D 10, 20 T363D107(2)020AS 10.0 8 CX02J107(2)
25 VOLT RATING AT 85°C
1.5 A 10, 20 T36(1)A155(2)025AS 0.5 5 CX02K155(2) CX12K155(2)
10.0 B 10, 20 T36(1)B106(2)025AS 2.0 6 CX02K106(2) CX12K106(2)
33.0 C 10, 20 T363C336(2)025AS 6.6 6 CX02K336(2)
68.0 D 10, 20 T363D686(2)025AS 10.0 6 CX02K686(2)
35 VOLT RATING AT 85°C
6.8 B 10, 20 T36(1)B685(2)035AS 1.9 5 CX02M685(2) CX12M685(2)
22.0 C 10, 20 T363C226(2)035AS 6.2 6 CX02M226(2)
33.0 D 10, 20 T363D336(2)035AS 9.2 6 CX02M336(2)
47.0 D 10, 20 T363D476(2)035AS 10.0 6 CX02M476(2)
50 VOLT RATING AT 85°C
0.1 A 10, 20 T36(1)A104(2)050AS 0.5 3 CX02N104(2) CX12N104(2)
0.15 A 10, 20 T36(1)A154(2)050AS 0.5 3 CX02N154(2) CX12N154(2)
0.22 A 10, 20 T36(1)A224(2)050AS 0.5 3 CX02N224(2) CX12N224(2)
0.33 A 10, 20 T36(1)A334(2)050AS 0.5 3 CX02N334(2) CX12N334(2)
0.47 A 10, 20 T36(1)A474(2)050AS 0.5 3 CX02N474(2) CX12N474(2)
0.68 A 10, 20 T36(1)A684(2)050AS 0.5 3 CX02N684(2) CX12N684(2)
1.0 A 10, 20 T36(1)A105(2)050AS 0.5 3 CX02N105(2) CX12N105(2)
1.5 B 10, 20 T36(1)B155(2)050AS 0.6 5 CX02N155(2) CX12N155(2)
2.2 B 10, 20 T36(1)B225(2)050AS 0.9 5 CX02N225(2) CX12N225(2)
3.3 B 10, 20 T36(1)B335(2)050AS 1.3 5 CX02N335(2) CX12N335(2)
4.7 B 10, 20 T36(1)B475(2)050AS 1.9 5 CX02N475(2) CX12N475(2)
6.8 C 10, 20 T363C685(2)050AS 2.7 5 CX02N685(2)
10.0 C 10, 20 T363C106(2)050AS 4.0 6 CX02N106(2)
15.0 C 10, 20 T363C156(2)050AS 6.0 6 CX02N156(2)
22.0 D 10, 20 T363D226(2)050AS 8.8 6 CX02N226(2)
TANTALUM DIPPED / RADIAL — MIL-PRF-49137/2
T363 (CX02), T369 (CX12) SERIES
T363/T369 & T368 Series
Tantalum Dipped / Radial
KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606 (864) 963-6300 67
RATINGS & PART NUMBER REFERENCE
(1) To complete KEMET part number, insert Series Designation as follows: 3 - T363 (CX02); 9 - T369 (CX12)
(2) To complete KEMET or military part number, insert Capacitance Tolerance Symbol as follows:
M - ±20%, K - ±10%
MAX.
DISSI-
PATION
CAPAC- D.C. FACTOR
ITANCE CASE LEAKAGE %@25°C,
µF SIZE KEMET PART NUMBER µA@25°C 120Hz
6 VOLT RATING AT 85°C
82.0 C T368C826(1)006A(2) 3.9 8
100.0 C T368C107(1)006A(2) 4.8 8
120.0 C T368C127(1)006A(2) 5.8 8
150.0 C T368C157(1)006A(2) 7.2 8
180.0 D T368D187(1)006A(2) 8.6 8
220.0 D T368D227(1)006A(2) 10.0 8
270.0 D T368D277(1)006A(2) 10.0 8
330.0 D T368D337(1)006A(2) 10.0 8
10 VOLT RATING AT 85°C
47.0 C T368C476(1)010A(2) 3.8 6
56.0 C T368C566(1)010A(2) 4.4 6
68.0 C T368C686(1)010A(2) 5.4 6
82.0 C T368C826(1)010A(2) 6.5 8
100.0 C T368C107(1)010A(2) 8.0 8
120.0 D T368D127(1)010A(2) 9.6 8
150.0 D T368D157(1)010A(2) 10.0 8
180.0 D T368D187(1)010A(2) 10.0 8
220.0 D T368D227(1)010A(2) 10.0 8
15 VOLT RATING AT 85°C
27.0 C T368C276(1)015A(2) 3.2 6
33.0 C T368C336(1)015A(2) 4.0 6
39.0 C T368C396(1)015A(2) 4.7 6
47.0 C T368C476(1)015A(2) 5.6 6
56.0 C T368C566(1)015A(2) 6.8 6
68.0 C T368C686(1)015A(2) 8.2 6
82.0 D T368D826(1)015A(2) 9.8 8
100.0 D T368D107(1)015A(2) 10.0 8
120.0 D T368D127(1)015A(2) 10.0 8
150.0 D T368D157(1)015A(2) 10.0 8
20 VOLT RATING AT 85°C
18.0 C T368C186(1)020A(2) 2.8 6
22.0 C T368C226(1)020A(2) 3.5 6
27.0 C T368C276(1)020A(2) 4.3 6
33.0 C T368C336(1)020A(2) 5.3 6
39.0 C T368C396(1)020A(2) 6.2 6
47.0 C T368C476(1)020A(2) 7.5 6
56.0 D T368D566(1)020A(2) 8.9 6
68.0 D T368D686(1)020A(2) 10.0 6
82.0 D T368D826(1)020A(2) 10.0 8
100.0 D T368D107(1)020A(2) 10.0 8
MAX.
DISSI-
PATION
CAPAC- D.C. FACTOR
ITANCE CASE LEAKAGE %@25°C,
µF SIZE KEMET PART NUMBER µA@25°C 120Hz
25 VOLT RATING AT 85°C
12.0 C T368C126(1)025A(2) 2.4 6
15.0 C T368C156(1)025A(2) 3.0 6
18.0 C T368C186(1)025A(2) 3.6 6
22.0 C T368C226(1)025A(2) 4.4 6
27.0 C T368C276(1)025A(2) 5.4 6
33.0 C T368C336(1)025A(2) 6.6 6
39.0 D T368D396(1)025A(2) 7.8 6
47.0 D T368D476(1)025A(2) 9.4 6
56.0 D T368D566(1)025A(2) 10.0 6
68.0 D T368D686(1)025A(2) 10.0 6
35 VOLT RATING AT 85°C
8.2 C T368C825(1)035A(2) 2.3 6
10.0 C T368C106(1)035A(2) 2.8 6
12.0 C T368C126(1)035A(2) 3.3 6
15.0 C T368C156(1)035A(2) 4.2 6
18.0 C T368C186(1)035A(2) 5.0 6
22.0 C T368C226(1)035A(2) 6.2 6
27.0 D T368D276(1)035A(2) 7.5 6
33.0 D T368D336(1)035A(2) 9.2 6
39.0 D T368D396(1)035A(2) 10.0 6
47.0 D T368D476(1)035A(2) 10.0 6
50 VOLT RATING AT 85°C
5.6 C T368C565(1)050A(2) 2.2 5
6.8 C T368C685(1)050A(2) 2.7 5
8.2 C T368C825(1)050A(2) 3.2 6
10.0 C T368C106(1)050A(2) 4.0 6
12.0 C T368C126(1)050A(2) 4.8 6
15.0 C T368C156(1)050A(2) 6.0 6
18.0 D T368D186(1)050A(2) 7.2 6
22.0 D T368D226(1)050A(2) 8.8 6
TANTALUM DIPPED / RADIAL
T368 SERIES “ULTRADIP II”
68 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606 (864) 963-6300
T368
RATINGS AND PART NUMBER REFERENCE
T368 CAPACITOR OUTLINE DRAWING
T368
DIMENSIONS — INCHES + (MILLIMETERS)
CASE
SIZE TMAX WMAX HMAX
0.250 0.40 0.42
C (6.35) (10.16) (10.67)
0.250 0.460 0.52
D (6.35) (11.68) (13.20)
(1) To complete KEMET part number, insert capacitance tolerance K– ±10%, M– ±20%,
or J– ±5% (Available on special order).
.187±.032
(4.75±.
81
)
H
.025±.002
(.64±.05)
.250±.015
(6.35±.38)
.100 MAX.
(2.54)
W
MAX.
T
MAX.
C & D CASES
* For Ordering and Marking Information refer to page 63.
(2) To complete KEMET part number, insert lead material designation: S = SnPb (tin/lead)
Effective June 30, 2005 T368 Series is RoHS Compliant.
and T = 100% Sn (tin).
T396/T398 Series
Tantalum Dipped / 3 Leaded
KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606 (864) 963-6300 69
TANTALUM DIPPED / 3 LEADED
T396 & T398 SERIES “ULTRADIP III”
KEMET UltraDip III Capacitors offer the advantages of solid tanta-
lum construction and a “fail-safe” insertion mechanism. The three-
leaded design (the anode is in the center) enables operators to
insert the capacitors into printed circuit boards correctly without hav-
ing to visually determine polarity. This timesaving device also elimi-
nates board damage that may result from incorrect insertion.
The UltraDip III Series features a capacitance range of 0.1 to 680
µF at 3 to 50 VDC. These miniature dipped solid tantalum capacitors
are encased in a tough plastic barrier coating that maintains the pre-
cise lead wire spacing within ±0.015 inch. The gold color epoxy per-
mits laser markings with outstanding permanency and legibility. All
case sizes are printed with capacitance, voltage and vendor I.D.
The UltraDip III Series from KEMET Capacitors exhibit low DCL,
ESR and Impedance and have excellent temperature stability.
These capacitors may be ordered with precut leads (see drawing for
lengths) or in KEMET Capacitor ARIS packaging (leads taped and
on reels) for high speed automatic insertion equipment.
CAPACITOR
OUTLINE DRAWING
Both T396 T398
Series Case W T H* H*
Size Width Thickness Height Height
T396/T398 A .280 (7.1) .190 (4.8) .310 (7.9) .355 (9.0)
T396/T398 B .280 (7.1) .190 (4.8) .320 (8.1) .365 (9.3)
T396/T398 C .280 (7.1) .200 (5.1) .360 (9.1) .390 (9.9)
T396/T398 D .280 (7.1) .200 (5.1) .370 (9.4) .390 (9.9)
T396/T398 E .280 (7.1) .230 (5.8) .380 (9.7) .415 (10.5)
T396/T398 F .280 (7.1) .240 (6.1) .410 (10.4) .430 (10.9)
T396/T398 G .280 (7.1) .250 (6.3) .420 (10.7) .440 (11.2)
T396/T398 H .280 (7.1) .270 (6.9) .420 (10.7) .440 (11.2)
T396/T398 J .300 (7.6) .300 (7.6) .460 (11.7) .480 (12.2)
T396/T398 K .340 (8.6) .340 (8.6) .500 (12.7) .500 (12.7)
T396/T398 L .340 (8.6) .340 (8.6) .560 (14.2) .580 (14.7)
T396/T398 M .360 (9.1) .360 (9.1) .620 (15.7) .620 (15.7)
DIMENSIONS—INCHES & (MILLIMETERS)
*NOTE: “H” dimensions are from seating plane to top of capacitor.
ORDERING INFORMATION
T 39X A 105 M 035 A S
TANTALUM
SERIES
T396 Straight leads
T398 Standoff leads
CASE SIZE
A, B, C, D, E, F, G, H, J, K, L & M
PICOFARAD CODE
First two digits are significant
figures. Third figure is the
number of zeros following.
LEAD MATERIAL
S — Sn/Pb (tin/lead)
FAILURE RATE LEVEL
A— Not Applicable
VOLTAGE RATING
For 6.3 Volts use 006
CAPACITANCE TOLERANCE
M — ±20% (K — 10% Special Order Only)
.187±.032
(4.75±.81)
.10±.008 (2.54±.20)
W
MAX.
T
MAX.
T398
H
MAX.
.20±.015 (5.08±.38)
.187±.05
(4.75±1.27)
.10±.008 (2.54±.20)
W
MAX.
T
MAX.
T396
H
MAX.
.02±.002
(.5±.05)
.20±.015 (5.08±.38)
-+-
.02±.002
(.5±.05)
Date
Code
Capacitance
(pF code)
KEMET
Trademark
106
16K
407
Voltage
Rating
CAPACITOR
MARKING
Effective June 30, 2005 the T396 and T398 Series are RoHS Compliant.
T– 100% Sn (tin)
MAX.
DISSI-
PATION
CAPAC- D.C. FACTOR
ITANCE CASE LEAKAGE %@25°C,
µF SIZE KEMET PART NUMBER µA@25°C 120Hz
3 VOLT RATING AT 85°C —
2 VOLT RATING AT 125°C
4.7 A T39(1)A475(2)003A(3) 0.5 56.8 A T39(1)A685(2)003A(3) 0.5 510.0 A T39(1)A106(2)003A(3) 0.5 615.0 B T39(1)B156(2)003A(3) 0.5 622.0 C T39(1)C226(2)003A(3) 0.5 633.0 D T39(1)D336(2)003A(3) 0.8 647.0 E T39(1)E476(2)003A(3) 1.1 668.0 F T39(1)F686(2)003A(3) 1.6 6
100.0 G T39(1)G107(2)003A(3) 2.4 8
150.0 H T39(1)H157(2)003A(3) 3.6 8
220.0 J T39(1)J227(2)003A(3) 5.3 8
330.0 K T39(1)K337(2)003A(3) 7.9 8
470.0 L T39(1)L477(2)003A(3) 10.0 9
680.0 M T39(1)M687(2)003A(3) 10.0 9
10 VOLT RATING AT 85°C —
7 VOLT RATING AT 125°C
2.2 A T39(1)A225(2)010A(3) 0.5 5
3.3 A T39(1)A335(2)010A(3) 0.5 5
4.7 A T39(1)A475(2)010A(3) 0.5 5
6.8 B T39(1)B685(2)010A(3) 0.5 5
10.0 C T39(1)C106(2)010A(3) 0.8 6
15.0 E T39(1)E156(2)010A(3) 1.2 6
22.0 E T39(1)E226(2)010A(3) 1.8 6
33.0 F T39(1)F336(2)010A(3) 2.6 6
47.0 H T39(1)H476(2)010A(3) 3.8 6
68.0 H T39(1)H686(2)010A(3) 5.4 6
100.0 J T39(1)J107(2)010A(3) 8.0 8
150.0 K T39(1)K157(2)010A(3) 10.0 8
220.0 l T39(1)L227(2)010A(3) 10.0 8
20 VOLT RATING AT 85°C —
13 VOLT RATING AT 125°C
1.0 A T39(1)A105(2)020A(3) 0.5 3
1.5 A T39(1)A155(2)020A(3) 0.5 5
2.2 A T39(1)A225(2)020A(3) 0.5 5
3.3 B T39(1)B335(2)020A(3) 0.5 5
4.7 C T39(1)C475(2)020A(3) 0.8 5
6.8 D T39(1)D685(2)020A(3) 1.1 5
10.0 E T39(1)E106(2)020A(3) 1.6 6
15.0 F T39(1)F156(2)020A(3) 2.4 6
22.0 G T39(1)G226(2)020A(3) 3.5 6
33.0 J T39(1)J336(2)020A(3) 5.3 6
47.0 K T39(1)K476(2)020A(3) 7.5 6
68.0 L T39(1)L686(2)020A(3) 10.0 6
100.0 M T39(1)M107(2)020A(3) 10.0 8
35 VOLT RATING AT 85°C —
23 VOLT RATING AT 125°C
0.10 A T39(1)A104(2)035A(3) 0.5 3
0.15 A T39(1)A154(2)035A(3) 0.5 3
0.22 A T39(1)A224(2)035A(3) 0.5 3
0.33 A T39(1)A334(2)035A(3) 0.5 3
0.47 A T39(1)A474(2)035A(3) 0.5 3
0.68 A T39(1)A684(2)035A(3) 0.5 3
1.0 A T39(1)A105(2)035A(3) 0.5 3
1.5 B T39(1)B155(2)035A(3) 0.5 5
2.2 C T39(1)C225(2)035A(3) 0.6 5
3.3 D T39(1)D335(2)035A(3) 0.9 5
4.7 E T39(1)E475(2)035A(3) 1.3 5
6.8 F T39(1)F685(2)035A(3) 1.9 5
10.0 G T39(1)G106(2)035A(3) 2.8 6
15.0 J T39(1)J156(2)035A(3) 4.2 6
22.0 K T39(1)K226(2)035A(3) 6.2 6
33.0 L T39(1)L336(2)035A(3) 9.2 6
47.0 M T39(1)M476(2)035A(3) 10.0 6
TANTALUM DIPPED / 3 LEADED —POLAR
T396 & T398 SERIES “ULTRADIP III”
70 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606 (864) 963-6300
RATINGS & PART NUMBER REFERENCE MAX.
DISSI-
PATION
CAPAC- D.C. FACTOR
ITANCE CASE LEAKAGE %@25°C,
µF SIZE KEMET PART NUMBER µA@25°C 120Hz
6.3 VOLT RATING AT 85°C —
4 VOLT RATING AT 125°C
3.3 A T39(1)A335(2)006A(3) 0.5 5
4.7 A T39(1)A475(2)006A((3) 0.5 5
6.8 A T39(1)A685(2)006A(3) 0.5 5
10.0 B T39(1)B106(2)006A(3) 0.5 6
15.0 C T39(1)C156(2)006A(3) 0.7 6
22.0 D T39(1)D226(2)006A(3) 1.1 6
33.0 E T39(1)E336(2)006A(3) 1.6 6
47.0 F T39(1)F476(2)006A(3) 2.3 6
68.0 G T39(1)G686(2)006A(3) 3.3 6
100.0 H T39(1)H107(2)006A(3) 4.8 8
150.0 J T39(1)J157(2)006A(3) 7.2 8
220.0 K T39(1)K227(2)006A(3) 10.0 8
330.0 L T39(1)L337(2)006A(3) 10.0 8
16 VOLT RATING AT 85°C —
10 VOLT RATING AT 125°C
1.5 A T39(1)A155(2)016A(3) 0.5 5
2.2 A T39(1)A225(2)016A(3) 0.5 5
3.3 A T39(1)A335(2)016A(3) 0.5 5
4.7 B T39(1)B475(2)016A(3) 0.6 5
6.8 C T39(1)C685(2)016A(3) 0.9 5
10.0 E T39(1)E106(2)016A(3) 1.3 6
15.0 E T39(1)E156(2)016A(3) 1.8 6
22.0 F T39(1)F226(2)016A(3) 2.6 6
33.0 H T39(1)H336(2)016A(3) 4.0 6
47.0 J T39(1)J476(2)016A(3) 5.6 6
68.0 K T39(1)K686(2)016A(3) 8.2 6
100.0 L T39(1)L107(2)016A(3) 10.0 8
150.0 M T39(1)M157(2)016A(3) 10.0 8
25 VOLT RATING AT 85°C —
16.5 VOLT RATING AT 125°C
1.0 A T39(1)A105(2)025A(3) 0.5 3
1.5 A T39(1)A155(2)025A(3) 0.5 5
2.2 B T39(1)B225(2)025A(3) 0.5 5
3.3 B T39(1)B335(2)025A(3) 0.7 5
4.7 C T39(1)C475(2)025A(3) 0.9 5
6.8 E T39(1)E685(2)025A(3) 1.4 5
10.0 E T39(1)E106(2)025A(3) 2.0 6
15.0 G T39(1)G156(2)025A(3) 3.0 6
22.0 H T39(1)H226(2)025A(3) 4.4 6
33.0 J T39(1)J336(2)025A(3) 6.6 6
47.0 K T39(1)K476(2)025A(3) 9.4 6
68.0 L T39(1)L686(2)025A(3) 10.0 6
50 VOLT RATING AT 85°C —
33 VOLT RATING AT 125°C
0.10 A T39(1)A104(2)050A(3) 0.5 3
0.15 A T39(1)A154(2)050A(3) 0.5 3
0.22 A T39(1)A224(2)050A(3) 0.5 3
0.33 A T39(1)A334(2)050A(3) 0.5 3
0.47 B T39(1)B474(2)050A(3) 0.5 3
0.68 B T39(1)B684(2)050A(3) 0.5 3
1.0 B T39(1)B105(2)050A(3) 0.5 3
1.5 E T39(1)E155(2)050A(3) 0.6 5
2.2 E T39(1)E225(2)050A(3) 0.9 5
3.3 F T39(1)F335(2)050A(3) 1.3 5
4.7 G T39(1)G475(2)050A(3) 1.9 5
6.8 J T39(1)J685(2)050A(3) 2.7 5
10.0 K T39(1)K106(2)050A(3) 4.0 6
15.0 L T39(1)L156(2)050A(3) 6.0 6
22.0 M T39(1)M226(2)050A(3) 8.8 6
(1) To complete KEMET Part Number, insert Series Designation as follows: “6” = T396, “8” = T398.
(2) To complete KEMET Part Number, insert Capacitance Tolerance Symbol as follows: “M” = ±20%, “K” = ±10%.
(3) To complete KEMET Part Number, insert Lead Material Designation: S = SnPb (tin/lead) and T = 100% Sn (tin).
NOTE: Higher voltage/tigher tolerance products may be shipped,
at KEMET’s option, within the same case size.
PACKAGING INFORMATION
72 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606 (864) 963-6300
KEMET offers Solid Tantalum Capacitors fully compatible for use with automatic insertion machines for radial-lead components. Aris Reeling meets
all requirements of EIA Standard RS-468. KEMET capacitors are wound on a precision made ARIS Reel Package. ARIS Ammo Package is also available.
Tantalum Dipped Radial – ARIS Specification (Automatic Radial Insertion System)
T
antalum Molded Radial – ARIS Specification (Automatic Radial Insertion System)
On polar devices, the positive (+) lead exits from container first.
* Lead spacings are 2.5mm (.098") center-to center
** Lead spacings are 5.0mm (.197") center-to-center.
On polar devices, the positive (+) lead exits from container first.
* Lead spacings are 2.5mm (.098") center-to-center (T350 A-H)
** Lead spacings are 5.0mm (.197") center-to-center
F
Dimensions:
0.100" ± .015
0.125" ± .015
0.200" ± .015
0.250" ± .015"
0.100 " ± .015 (3 leaded)
P1 Dimensions:
Lead
Spacing
0.100" – 0.200 ± .028"
0.125" – 0.187 ± .028"
0.200" – 0.150 ± .028"
0.250" – 0.125 ± .028"
0.100" – 0.100 ± .028" ( 3 leaded)
➀
T330**
T340**
T370
P2
H
A
W
1
W0
W
2
W2
P
0
T
d
L1
A
1
P
H
1
W
D
0
P
1
F
➀
➁
➂
➁➂
T350/1*
T396/8*
T352/3/6**
1MM Max.
(.039")
Tape
Carrier
T0
ΔH
P
2
H
A
W0
W
2
W
2
P0
T
d
L
1
A
1
P
H
1
W
1
P
1
F
W
D0
➀➁➂
➀
➁
➂
L
H0
Body Height (1)
Body Width (1)
Sprocket Hole
Diameter
Lead Diameter
Lead Center (5)
Component Base
to Tape Center (2)(4)(6)
Lead Standoff
Height
Component Height
Abov e T ape Center
Component Alignment
Front to Rear
Cut Out Length
Lead Protrustion
Dimension Symbol Nominal
mm (inch) Tolerance
mm (inch) Dimension Symbol Nominal
mm (inch) Tolerance
mm (inch)
Component Pitch (5)
Sprocket Hole
Pitch (3)
Sprocket Hole
Center to Lead
Center (4) (5)
Sprocket Hole Center
to Component Center
Body Thickness
Total Tape Thickness
Carrier Tape Width
Hold-Down Tape
Width
Sprocket Hole
Location
Hold-Down Tape
Location
A
A1
D0
d
F
H
H0
H1
Δ H
L
L1
10.50 (.413)
15.24 (.600)
4.0 (.157)
0.51 or 0.64
(.020) (.025)
5.0 2.5
(.197) (.098)
16.0 - 21.0
N/A
32.25 (1.270)
0
11.0 (.433)
2.0 (.079)
± .38 (±.015)
Maximum
Maximum ± .38
± (.015)
± 0.3 (± .012)
± 0.05 or ± .03
(± .001)
+ 0.8/ - 0.2
(+ .032/ -.008)
Reference Only
Maximum
± 2.0
(± .079)
Maximum
Maximum
12.7 (.500)
12.7 (.500)
3.85 4.76 5.1
(.152) (.188) (.201)
6.35 (.250)
6.35 (.250)
0.7 (0.28)
18.0 (.709)
15 or 6
(.561) (.236)
9.0 (.354)
3.0 or 12.0
(.118) (.472)
P
P0
P1
P2
T0
T
W
W0
W1
W2
± 1.0 (± .039)
± 0.3 (±.012)
± 0.7 (±.028)
± 1.3 (±.051)
± 1.3 Maximum
± .02 (±.008)
+ 1.0/-0.5
(+.039/-.020)
+ 1.0/-0.8
(+.039/.031)
+.075/-0.5
(+.030/-.020)
Maximum
Notes: (1) See page 50 for T330, page 53 for T340 and page 59 for T35X specific dimensions.
(2) Reference Only
(3) Cumulative pitch error ± 1.0mm (.039") maximum in 20 consecutive sprocket hole locations.
(4) Measured at bottom of standoff.
(5) P, P1 and F measured at egress from carrier tape.
(6) H dimensions for T370 D and E 16.5mm ± 0.5mm (0.650" ± 0.020")
Tantalum Molded Tape and Reel Dimensions in Millimeters & (Inches)
Body Height (1)
Body Width (1)
Sprocket Hole
Diameter
Lead Diameter
Lead Center (4)
Component Base
to Tape Center (4)
Lead Standoff
Height
Component Height
Above T ape Center
Component Alignment
Front to Rear
Cut Out Length
Lead Protrustion
Dimension Symbol Nominal
mm (inch) Tolerance
mm (inch) Dimension Symbol Nominal
mm (inch) Tolerance
mm (inch)
Component Pitch (5)
Sprocket Hole
Pitch (2)
Sprocket Hole
Center to Lead
Center (3) (4)
Sprocket Hole Center
to Component (5)
Center
Body Thickness
Total T ape Thickness
Carrier T ape Width
Hold-Down Tape
Width
Sprocket Hole
Location
Hold-Down Tape
Location
A
A1
D0
d
F
H
H0
H1
Δ H
L
L1
17.0 (0.67)
10.2 (0.40)
4.0 (.157)
0.51 or 0.64
(.020) (.025)
See Note Below
C-7301 C-7303
16.0 (.630) 18.0 (.709)
C-7301 C-7303
16.0 (.630) 18.0 (.709)
32.25 (1.270)
0
11.0 (.433)
1.0 (.039)
Maximum
Maximum
± 0.3 (±.012)
± 0.05 (.002)
C-7301 C-7303
±0.5 (±.020) Minimum
C-7301 C-7303
±0.5 (±.020) Minimum
Maximum
1.0 (.039)
Maximum
Maximum
12.7 (.500)
12.7 (.500)
See Note
Below
See Note
Below
10.2 (.400)
0.7 (0.28)
18.0 (.709)
15mm or 6mm
(.561) (.236)
9.0 (.354)
12mm (.472)
P
P0
P1
P2
T0
T
W
W0
W1
W2
± 1.0 (± .039)
± 0.3 (±.012)
± 0.7 (±.028)
Maximum
± .02 (.008)
+ 1.0/-0.5
(+.039/-.020)
+ 1.0/-0.8
(+.039/-.031)
+.075/-0.5
(+.030/-.020)
Maximum
Notes: (1) See page 62 for T35X and page 69 for T39X specific dimensions.
(2) Cumulative pitch error ± 1.0mm (.039) maximum in 20 consecutive sprocket hole locations.
(3) Measured at bottom of standoff.
(4) P1 and F measured at egress from carrier tape.
(5) P and P2 measured at egress from carrier tape.
Tantalum Dipped Tape and Reel Dimensions in Millimeters & (Inches)
T354#
➃
T355+
➄
# Lead spacings are 6.35mm (.25") center-to-center
+ Lead spacings are 3.18mm (.125") center-to-center
(.630 - .827)
TANTALUM PACKAGING
Standard Standard Standard Ammo Ammo
KEMET(1) Military Military Case Bulk(2) Reel Reel Reeling Pack Pack
Number Style Specification Size Quantity Quantity Size Spec. Quantity Spec.
T110/T212, CSR13 MIL-C-39003/1 A 150/Box 3500 12" C-7200 1500 C-7293
T140/T242, CSR23 MIL-C-39003/3 B 75/Box 2500 12" C-7200 1000 Class I
T252, CSR33 MIL-C-39003/6 C 20/Tray 500 12" C-7200 250 C-7442
T262 CSR21 MIL-C-39003/9 D 20/Tray 400 12" C-7200 250 Class II
C-7443
Class III
See Page 71
for class info.
T111/T213 CSR91 MIL-C-39003/4 A 60/Box 3000 12" C-7200 N/A N/A
B 30/Box 2000 12" C-7200
C 10/Card N/A N/A N/A
D 10/Card N/A N/A N/A
T210, A 40/Tray 3500 12" C-7200 N/A N/A
T216, CSS13 MIL-C-39003/10 B 30/Tray 2500 12" C-7200 N/A N/A
T240, C 20/Tray 500 12" C-7200 N/A N/A
T256 CSS33 MIL-C-39003/10 D 20/Tray 400 12" C-7200 N/A N/A
T222 CSR09 MIL-C-39003/2 A/B 50/Tray N/A N/A N/A N/A N/A
A 300/Box N/A N/A N/A N/A
B 150/Box
T322/T323 CX01, MIL-C-49137/1 & 5 A 300 4500 12" C-7200 2000 C-7293
CX05 B 250 4000 12" C-7200 2000 Class I
C 100 2500 12" C-7200 1000 C-7442
D 100 2500 12" C-7200 1000 Class II
E 100 500 12" C-7200 250 C-7443
F 100 500 12" C-7200 250 Class III
See Page 71
T330 A 400 1000 12" C-7301 1600
B 300 1000 12" C-7301 1200
C 200 1000 12" C-7301 1200
D 100 N/A N/A N/A N/A
T340 A 300 1000 12" C-7301 1600
B 300 1000 12" C-7301 1500
C 200 1000 12" C-7301 1500
D 100 250 12" C-7301 450
E 50 150 12" C-7301 N/A
F 100 N/A N/A N/A N/A
T350, A 1000 1500 12"
C-7301/7303
2500
T351, B 1000 1500 12"
C-7301/7303
2500
T352, C 1000 1500 12"
C-7301/7303
2500
T353, D 1000 1000 12"
C-7301/7303
2000
T354, E 1000 1000 12"
C-7301/7303
2000
T355, F 500 1000 12"
C-7301/7303
1500
T356 G 500 1000 12"
C-7301/7303
1500
H 500 800 12"
C-7301/7303
1500
J 100 800 12"
C-7301/7303
800
K 100 500 12"
C-7301/7303
800
L, M 100 500 12" See Page 72 500
PACKAGING INFORMATION
Lead Tape & Reel
Packaging
KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606 (864) 963-6300 73
NOTE: (1) Each KEMET number in its section applies to all case sizes. (2) Standard packaging refers to number of pieces per bag, box, tray or vial.
PACKAGING INFORMATION
74 KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606 (864) 963-6300
TANTALUM PACKAGING (Continued)
Standard Standard Standard
KEMET(1) Military Military Case Bulk(2) Reel Reel Reeling Ammo
Number Style Specification Size Quantity Quantity Size Spec. Packs
T363 CX02 MIL-C-49137/2 A 1000 1500 12”
C-7301/7303
2500
B 1000 1500 12”
C-7301/7303
2000
C 500 500 12”
C-7301/7303
800
D 500 500 12” See Page 72 800
T368 C 500 500 12”
C-7301/7303
800
D 500 500 12”
C-7301/7303
800
T369 CX12 MIL-C-49137/2 A 1000 1500 12”
C-7301/7303
2500
B 1000 1500 12”
C-7301/7303
2000
T370 C 500 N/A N/A N/A N/A
D 500 1000 12” C-7301 N/A
E 500 1000 12” C-7301 N/A
F 250 N/A N/A N/A N/A
T378 CX06 MIL-C-49137/6 D 200 1000 12”
C-7301
N/A
E 180 1000 12”
C-7301
N/A
F 50 N/A N/A N/A N/A
T396, A-B 1000 1500 12”
C-7301/7303
2000
T398 C 500 1500 12”
C-7301/7303
2000
D-F 500 1000 12”
C-7301/7303
1500
G 500 1000 12”
C-7301/7303
2000
H 500 800 12”
C-7301/7303
2000
J 250 800 12”
C-7301/7303
1600
K 250 500 12”
C-7301/7303
800
L-M 250 500 12”
C-7301/7303
500
NOTE: (1) Standard packaging refers to number of pieces per bag, box, tray or vial. (2) Quantity varies. For further details, please consult the factory.
