GQ TESTING ULTRA-SMALL PACKAGE FLAT POLARIZED RELAY GQ-RELAYS FEATURES 7.200.3 .283.012 10.600.3 .417.012 5.200.2 .205.008 10.600.3 .417.012 7.200.3 .283.012 Max.5.40 .213 mm inch * Compact flat body saves space With a small footprint of 10.6 mm (L) x 7.2 mm (W) .417 inch (L) x .283 inch (W) for space savings, it also has a very short height of 5.2 mm .205 inch. (Standard PC board type.) * Outstanding surge resistance. Surge withstand between open contacts: 1,500 V 10x160 s (FCC part 68) Surge withstand between contacts and coil: 2,500 V 2x10 s (Bellcore) * The use of twin crossbar contacts ensures high contact reliability. AgPd contact is used because of its good sulfide resistance. Adopting low-gas molding material. Coil assembly molding technology which avoids generating volatile gas from coil. * Increased packaging density Due to highly efficient magnetic circuit design, leakage flux is reduced and changes in electrical characteristics from components being mounted close-together are minimized. This all means a packaging density higher than ever before. * Nominal operating power: 140 mW * Outstanding vibration and shock resistance. Functional shock resistance: 750 m/s2 {75G} Destructive shock resistance: 1,000 m/s2 {100G} Functional vibration resistance: 10 to 55 Hz (at double amplitude of 3.3 mm .130 inch) Destructive vibration resistance: 10 to 55 Hz (at double amplitude of 5 mm .197 inch) SPECIFICATIONS Contact Characteristics Arrangement Initial contact resistance, max. (By voltage drop 6 V DC 1A ) Contact material Rating Nominal operating power Expected life (min. operations) Nominal switching capacity (resistive load) Max. switching power (resistive load) Max. switching voltage Max. switching current Min. switching capacity 1 Single side stable 1 coil latching Mechanical (at 180 cpm) 1 A 30 V DC resistive Electrical (at 20 cpm) 0.3 A 125 V AC resistive 2 Form C 100 m Stationary: AgPd+Au clad Movable: AgPd 1 A 30 V DC 0.3 A 125 V AC 30 W, 37.5 V A 110 V DC, 125 V AC 1A 10 A 10 mV DC 140mW (1.5 to 12 V DC) 230mW (24 V DC) 100mW (1.5 to 12 V DC) 120mW (24 V DC) 5 x 107 105 105 Remarks: * Specifications will vary with foreign standards certification ratings. *1 Measurement at same location as "Initial breakdown voltage" section. *2 Detection current: 10mA. *3 Nominal voltage applied to the coil, excluding contact bounce time. *4 By resistive method, nominal voltage applied to the coil; contact carrying current: 1 A. *5 Half-wave pulse of sine wave: 6 ms;detection time: 10s. 6 * Half-wave pulse of sine wave: 6 ms. *7 Detection time: 10s. *8 Refer to 5. Conditions for operation, transport and storage mentioned in AMBIENT ENVIRONMENT (Page 61) Initial insulation resistance*1 Min. 1,000M (at 500V DC) Between open contacts 750 Vrms for 1min. Initial breakdown Between contact sets 1,000 Vrms for 1min. voltage*2 Between contacts and coil 1,500 Vrms for 1min. Between open contacts 1,500 V(FCC Part 68) Initial surge (10x160 s) voltage Between contacts and coil 2,500 V(Bellcore) (2x10 s) Max. 4 ms (Approx. 2 ms) Operate time [Set time]*3 (at 20C) [Max. 4 ms (Approx. 2 ms)] Release time (without diode) Max. 4 ms (Approx. 1 ms) [Reset time]*3 (at 20C) [Max. 4 ms (Approx. 2 ms)] Temperature rise*4 (at 20C) Max. 50C Functional*5 Min. 750 m/s2{75G] Shock resistance Destructive*6 Min. 1,000 m/s2{100G] 10 to 55 Hz at double Functional*7 amplitude of 3.3 mm Vibration resistance 10 to 55 Hz at double Destructive amplitude of 5 mm Conditions for opera- Ambient -40C to 85C tion, transport and temperature 2 -40F to 185F storage*8 (Not freezing and conHumidity 5 to 85% R.H. densing at low temperature) Unit weight Approx. 1 g .035 oz Notes: 1 This value can change due to the switching frequency, environmental conditions, and desired reliability level, therefore it is recommended to check this with the actual load. 2 The upper limit for the ambient temperature is the maximum temperature that can satisfy the coil temperature rise. Under the packing condition, allowable temperature range is from -40 to +70C -40 to +158F. 129 GQ TYPICAL APPLICATIONS * Telephone exchange, transmission equipment * Communications devices * Measurement devices * Home appliances, and audio/visual equipment * Handheld and portable products ORDERING INFORMATION Ex. AGQ Contact arrangement Operating function 2: 2 Form C 2 0 0 A 1 H Z Type of operation Terminal shape 0: Standard type (B.B.M.) Nil: Standard PC board terminal A: Surface-mount terminal A type S: Surface-mount terminal S type 0: Single side stable 1: 1 coil latching Packing style Coil voltage (DC) 1H: 1.5V 03 : 3V 4H: 4.5V 06 : 6V 09 : 9V 12 : 12V 24 : 24V Nil: Tube packing Z: Tape and reel packing (piked from 5/6/7/8 pin side) Note: Tape and reel packing symbol "-Z" is not marked on the relay. "X" type tape and reel packing (picked from 1/2/3/4-pin side) is also available. Suffix "X" instead of "Z". TYPES AND COIL DATA (at 20C 68F) (1) Standard PC board terminal Part No. Operating Function Single side stable Pick-up voltage, V DC (max.) (initial) 1.13 2.25 3.38 4.5 6.75 9 18 Drop-out voltage, V DC (min.) (initial) 0.15 0.3 0.45 0.6 0.9 1.2 2.4 Coil Rating, V DC Set voltage, V DC (max.) (initial) 1.5 3 4.5 6 9 12 24 1.13 2.25 3.38 4.5 6.75 9 18 Coil Rating, V DC Standard PC board terminal AGQ2001H AGQ20003 AGQ2004H AGQ20006 AGQ20009 AGQ20012 AGQ20024 1.5 3 4.5 6 9 12 24 Part No. Operating Function 1 coil latching Standard PC board terminal AGQ2101H AGQ21003 AGQ2104H AGQ21006 AGQ21009 AGQ21012 AGQ21024 Nominal operating current, mA (10%) Coil resistance, (10%) Nominal operating power, mW Max. allowable voltage, V DC 93.8 46.7 31 23.3 15.5 11.7 9.6 16 64.2 145 257 579 1,028 2,504 140 140 140 140 140 140 230 2.25 4.5 6.75 9 13.5 18 28.8 Reset voltage, V DC (max.) (initial) Nominal operating current, mA (10%) Coil resistance, (10%) Nominal operating power, mW Max. allowable voltage, V DC 1.13 2.25 3.38 4.5 6.75 9 18 66.7 33.3 22.2 16.7 11.1 8.3 5.0 22.5 90 202.5 360 810 1,440 4,800 100 100 100 100 100 100 120 2.25 4.5 6.75 9 13.5 18 36 1) Standard packing: 50 pcs. in an inner package (tube); 1,000 pcs. in an outer package 2) Specified value of pick-up, drop-out, set and reset voltage is with the condition of square wave coil pulse. (2) Surface-mount terminal Part No. Operating Function Single side stable Tube packing Tape and reel packing AGQ2001H AGQ20003 AGQ2004H AGQ20006 AGQ20009 AGQ20012 AGQ20024 AGQ2001HZ AGQ20003Z AGQ2004HZ AGQ20006Z AGQ20009Z AGQ20012Z AGQ20024Z Coil Rating, V DC 1.5 3 4.5 6 9 12 24 Pick-up voltage, V DC (max.) (initial) 1.13 2.25 3.38 4.5 6.75 9 18 Drop-out voltage, V DC (min.) (initial) 0.15 0.3 0.45 0.6 0.9 1.2 2.4 Nominal operating current, mA (10%) 93.8 46.7 31 23.3 15.5 11.7 9.6 Coil resistance, (10%) 16 64.2 145 257 579 1,028 2,504 Nominal operating power, mW 140 140 140 140 140 140 230 Max. allowable voltage, V DC 2.25 4.5 6.75 9 13.5 18 28.8 : For each surface-mounted terminal variation, input the following letter. A type: A, S type: S 1) Standard packing: 50 pcs.(tube), 900pcs. (tape and reel)in an inner package; 1,000 pcs.(tube), 1,800pcs. (tape and reel)in an outer package 2) Specified value of pick-up, drop-out, set and reset voltage is with the condition of square wave coil pulse. 130 GQ Part No. Operating Function 1 coil latching Tube packing Tape and reel packing AGQ2101H AGQ21003 AGQ2104H AGQ21006 AGQ21009 AGQ21012 AGQ21024 AGQ2101HZ AGQ21003Z AGQ2104HZ AGQ21006Z AGQ21009Z AGQ21012Z AGQ21024Z Coil Rating, V DC Set voltage, V DC (max.) (initial) 1.5 3 4.5 6 9 12 24 1.13 2.25 3.38 4.5 6.75 9 18 Reset voltage, V DC (max.) (initial) 1.13 2.25 3.38 4.5 6.75 9 18 Nominal operating current, mA (10%) 66.7 33.3 22.2 16.7 11.1 8.3 5.0 Coil resistance, (10%) 22.5 90 202.5 360 810 1,440 4,800 Nominal operating power, mW 100 100 100 100 100 100 120 Max. allowable voltage, V DC 2.25 4.5 6.75 9 13.5 18 36 : For each surface-mounted terminal variation, input the following letter. A type: A, S type: S 1) Standard packing: 50 pcs.(tube), 900pcs. (tape and reel)in an inner package; 1,000 pcs.(tube), 1,800pcs. (tape and reel)in an outer package 2) Specified value of pick-up, drop-out, set and reset voltage is with the condition of square wave coil pulse. DIMENSIONS mm inch PC board pattern 1. PC board terminal 10.600.3 .417.012 7.200.3 .283.012 5.200.2 .205.008 2.20 .087 3.20 .126 0.400.1 .016.004 3.200.15 .126.006 2 3 4 8 7 6 5 8-0.85 dia. 8-.033 dia. Direction indication Suggested mounting pad Single side stable/ 1 coil latching 1) A type 7.200.3 .283.012 10.600.3 .417.012 2.20 .087 2.20 .087 3.20 .126 0.400.1 .016.004 3.200.15 .126.006 2.200.15 .087.006 2.200.15 .087.006 1 2 3 4 8 7 6 5 2.20 .087 Direction indication Tolerance: 0.1 .004 2. Surface-mount terminal Max. 5.40 .213 1 1 coil latching (Reset condition) 5.08 .200 0.200.1 .008.004 5.080.15 .200.006 2.200.15 .087.006 3.500.3 2.200.15 .138.012 .087.006 Schematic (Bottom view) Single side stable (Deenergized condition) 0.200.1 .008.004 5.080.15 .200.006 8.400.3 .331.012 2.66 6.74 .105 .265 Schematic (Top view) Single side stable (Deenergized condition) 8 7 6 5 1 2 3 4 Direction indication 0.80 .031 1 coil latcing (Reset condition) 8 7 6 5 1 2 3 4 Direction indication Suggested mounting pad Single side stable/ 1 coil latching 1) S type Max. 5.40 .213 7.200.3 .283.012 10.600.3 .417.012 2.20 .087 2.20 .087 3.20 .126 0.400.1 .016.004 3.200.15 .126.006 0.200.1 .008.004 5.080.15 .200.006 2.200.15 .087.006 2.200.15 .087.006 2.06 .081 6.14 .242 0.80 .031 7.200.3 .283.012 Tolerance: 0.1 .004 REFERENCE DATA 1. Max. switching capacity 2. Life curve DC resistive load AC resistive load 1.0 0.3 No. of operations, x 104 Switching current, A 100 50 40 30 DC 30V resistive load 20 AC 125V resistive load 10 30 100 Contact voltage, V 0 0.2 0.4 0.6 0.8 1.0 1.2 Switching current, A 131 GQ NOTES 1. Coil operating power 1) As a general rule, only a pure DC power supply should be used for the coil drive. 2) To ensure proper operation, the voltage applied to both terminals of the coil should be 5% (at 20C 68F) the rated operating voltage of the coil. Also, be aware that the pick-up and drop-out voltages will fluctuate depending on the ambient temperature and operating conditions. 3) The ripple factor for the voltage applied to the coil should be less than 5%. 4) For set and reset latching relays, the rated operating voltage should be applied to the coil for 10 ms or more. 2. Coil connection When connecting coils, refer to the wiring diagram to prevent mis-operation or malfunction. 3. External magnetic field Since GQ relays are highly sensitive polarized relays, their characteristics will be affected by a strong external magnetic field. Avoid using the relay under that condition. 4. Cleaning In automatic cleaning, cleaning with the boiling method is recommended. Avoid ultrasonic cleaning which subject the relay to high frequency vibrations. It may cause the contacts to stick. lt is recommended that a fluorinated hydrocarbon or other alcoholic solvent be used. 5. Packing style 1) The relay is packed in a tube with the relay orientation mark on the left side, as shown in the figure below. Orientation (indicates PIN No.1)stripe Stopper (green) Stopper (red) 2) Tape and reel packing (A type) (1)-1 Tape dimensions mm inch Relay polarity bar (Z type) 1.50 +0.1 0 dia. .059 +.003 .0 dia. 2.00dia. 4.00 .079dia. .157 1.75 .069 2.0 .079 Max. 6.55 .256 0.40 .016 11.5 .453 24.00.3 .945.012 11.1 .437 9.0 .354 12.0 .472 GQ relays Tape coming out direction General tolerance 0.1 mm .004 inch (S type) (1)-2 Tape dimensions Relay polarity bar (Z type) 1.50 +0.1 0 dia. .059 +.003 .0 dia. 4.0 2.00dia. .157 .079dia. 1.75 .069 2.0 .079 Max. 6.55 .256 0.40 .016 11.5 .453 24.00.3 .945.012 11.1 .437 GQ relays 7.8 .307 12.0 .472 Tape coming out direction General tolerance 0.1 mm .004 inch (2) Dimensions of plastic peel mm inch 210.8 dia. .827.031 dia. 2.00.5 .079.020 1001 dia. 3.937.039 dia. 3302 dia. 12.992.079 dia. 24.4 +20 130.2 dia. .961 +.079 0 .512.008 dia. 2.00.2 .079.008 6. Automatic insertion To maintain the internal function of the relay, the chucking pressure should not exceed the values below. Chucking pressure in the direction A : 9.8 N {1 kgf} or less Chucking pressure in the direction B : 9.8 N {1 kgf} or less Chucking pressure in the direction C : 9.8 N {1 kgf} or less Orientation (indicates PIN No.1)stripe Stopper (green) Stopper (red) C B , , , , A Please chuck the portion. Avoid chucking the center of the relay. In addition, excessive chucking pressure to the pinpoint of the relay should be also avoided. For Cautions for Use, see Relay Technical Information (Page 48 to 76). 9/1/2000 132 All Rights Reserved, (c) Copyright Matsushita Electric Works, Ltd. Go To Online Catalog