GQ
129
GQ-RELAYS
ULTRA-SMALL PACKAGE
FLAT POLARIZED RELAY
7.20±0.3
.283±.012
10.60±0.3
.417±.012 5.20±0.2
.205±.008
10.60±0.3
.417±.012 Max.5.40
.213
7.20±0.3
.283±.012
mm inch
FEATURES
• Compact flat body saves space
With a small footprint of 10.6 mm (L)
×
7.2
mm (W) .417 inch (L)
×
.283 inch (W) for
space savings, it also has a very short
height of 5.2 mm .205 inch. (Standard PC
board type.)
• Outstanding surge resistance.
Surge withstand between open contacts:
1,500 V 10
×
160
µ
s (FCC part 68)
Surge withstand between contacts and
coil: 2,500 V 2
×
10
µ
s (Bellcore)
The use of twin cr ossbar contacts en-
sures high contact reliability.
AgPd contact is used because of its good
sulfide resistance. Adopting low-gas
molding material. Coil assembly molding
technology which avoids generating vola-
tile gas from coil.
• Increased packaging density
Due to highly efficient magnetic circuit de-
sign, leakage flux is reduced and changes
in electrical characteristics from compo-
nents being mounted close-together are
minimized. This all means a packaging
density higher than ever before.
• Nominal operating power: 140 mW
• Outstanding vibration and shock re-
sistance.
Functional shock resistance:
750 m/s
2
{75G}
Destructive shock resistance:
1,000 m/s
2
{100G}
Functional vibration resistance:
10 to 55 Hz (at double amplitude of 3.3
mm .130 inch)
Destructive vibration resistance:
10 to 55 Hz (at double amplitude of 5 mm
.197 inch)
SPECIFICATIONS
Contact
Remarks:
* Specifications will vary with foreign standards certification ratings.
*
1
Measurement at same location as "Initial breakdown voltage" section.
*
2
Detection current: 10mA.
*
3
Nominal voltage applied to the coil, excluding contact bounce time.
*
4
By resistive method, nominal v oltage applied to the coil; contact carrying current:
1 A.
*
5
Half-wave pulse of sine wave: 6 ms;detection time: 10
µ
s.
*
6
Half-wave pulse of sine wave: 6 ms.
*
7
Detection time: 10
µ
s
.
*
8
Refer to 5. Conditions for operation, transpor t and storage mentioned in
AMBIENT ENVIRONMENT (Page 61)
Characteristics
Notes:
1 This value can change due to the s witching frequency , environmental conditions,
and desired reliability level, therefore it is recommended to check this with the
actual load.
2 The upper limit for the ambient temperature is the maximum temperature that
can satisfy the coil temperature rise. Under the packing condition, allowable
temperature range is from –40 to +70
°
C –40
°
to +158
°
F.
Arrangement 2 Form C
Initial contact resistance, max.
(By voltage drop 6 V DC 1A ) 100 m
Contact material Stationary: AgPd+A u clad
Movable: AgPd
Rating
Nominal switching capacity
(resistive load) 1 A 30 V DC
0.3 A 125 V AC
Max. switching power
(resistive load) 30 W, 37.5 V A
Max. switching voltage 110 V DC, 125 V AC
Max. switching current 1 A
Min. switching capacity
1 10
µ
A 10 mV DC
Nominal
operating
power
Single side stable 140mW (1.5 to 12 V DC)
230mW (24 V DC)
1 coil latching 100mW (1.5 to 12 V DC)
120mW (24 V DC)
Expected
life (min.
operations)
Mechanical (at 180 cpm) 5
×
10
7
Electrical
(at 20 cpm)
1 A 30 V DC
resistive 10
5
0.3 A 125 V AC
resistive 10
5
Initial insulation resistance*
1
Min. 1,000M
(at 500V DC)
Initial
breakdown
voltage*
2
Between open contacts 750 Vrms for 1min.
Between contact sets 1,000 Vrms for 1min.
Between contacts and coil 1,500 Vrms for 1min.
Initial surge
voltage
Between open contacts
(10
×
160
µ
s) 1,500 V(FCC Part 68)
Between contacts and coil
(2
×
10
µ
s) 2,500 V(Bellcore)
Operate time [Set time]*
3
(at 20
°
C) Max. 4 ms (Approx. 2 ms)
[Max. 4 ms (Approx. 2 ms)]
Release time (without diode)
[Reset time]*
3
(at 20
°
C) Max. 4 ms (Approx. 1 ms)
[Max. 4 ms (Approx. 2 ms)]
Temperature rise*
4
(at 20
°
C) Max. 50
°
C
Shock resistance Functional*
5
Min. 750 m/s
2
{75G]
Destructive*
6
Min. 1,000 m/s
2
{100G]
Vibration resistance Functional*
7
10 to 55 Hz at double
amplitude of 3.3 mm
Destructive 10 to 55 Hz at double
amplitude of 5 mm
Conditions for opera-
tion, transport and
storage*
8
(Not freezing and con-
densing at low tem-
perature)
Ambient
temperature
2–40
°
C to 85
°
C
–40
°
F to 185
°
F
Humidity 5 to 85% R.H.
Unit weight Approx. 1 g .035 oz
TESTING
GQ
130
TYPICAL APPLICATIONS
Telephone exchange, transmission
equipment
• Communications devices
• Measurement devices
• Home appliances, and audio/visual
equipment
• Handheld and portable products
ORDERING INFORMATION
200A Z1HEx. AGQ
Contact arrangement
Terminal shapeOperating function Packing style
Coil voltage (DC)
Nil: Standard PC board terminal
A: Surface-mount terminal A type
S: Surface-mount terminal S type
2: 2 Form C 0: Single side stable
1: 1 coil latching
Type of operation
0: Standard type
(B.B.M.)
Nil: Tube packing
Z:
Tape and reel packing
(piked from 5/6/7/8
pin side)
1H: 1.5V
03
: 3V
4H: 4.5V
06
: 6V
09
: 9V
12
: 12V
24
: 24V
Note: Tape and reel packing symbol “-Z” is not marked on the relay. “X” type tape and reel packing (picked from 1/2/3/4-pin side) is also available. Suffix “X” instead of “Z”.
TYPES AND COIL DATA (at 20
°
C 68
°
F)
(1) Standard PC board terminal
1) Standard packing: 50 pcs. in an inner package (tube); 1,000 pcs. in an outer package
2) Specified value of pick-up, drop-out, set and reset voltage is with the condition of square wave coil pulse.
(2) Surface-mount terminal
: For each surface-mounted terminal variation, input the following letter.
A type: A, S type: S
1) Standard packing: 50 pcs.(tube), 900pcs. (tape and reel)in an inner package; 1,000 pcs.(tube), 1,800pcs. (tape and reel)in an outer package
2) Specified value of pick-up, drop-out, set and reset voltage is with the condition of square wave coil pulse.
Operating
Function
Part No. Coil Rating,
V DC
Pick-up volt-
age, V DC
(max.)
(initial)
Drop-out
voltage,
V DC (min.)
(initial)
Nominal
operating
current,
mA (
±
10%)
Coil resistance,
(
±
10%) Nominal
operating
power, mW
Max. allowable
voltage,
V DC
Standard PC
board terminal
Single side
stable
AGQ2001H 1.5 1.13 0.15 93.8 16 140 2.25
AGQ20003 3 2.25 0.3 46.7 64.2 140 4.5
AGQ2004H 4.5 3.38 0.45 31 145 140 6.75
AGQ20006 6 4.5 0.6 23.3 257 140 9
AGQ20009 9 6.75 0.9 15.5 579 140 13.5
AGQ20012 12 9 1.2 11.7 1,028 140 18
AGQ20024 24 18 2.4 9.6 2,504 230 28.8
Operating
Function
Part No. Coil Rating,
V DC Set voltage,
V DC (max.)
(initial)
Reset voltage ,
V DC (max.)
(initial)
Nominal
operating
current,
mA (
±
10%)
Coil resistance,
(
±
10%) Nominal
operating
power, mW
Max. allowable
voltage,
V DC
Standard PC
board terminal
1 coil
latching
AGQ2101H 1.5 1.13 1.13 66.7 22.5 100 2.25
AGQ21003 3 2.25 2.25 33.3 90 100 4.5
AGQ2104H 4.5 3.38 3.38 22.2 202.5 100 6.75
AGQ21006 6 4.5 4.5 16.7 360 100 9
AGQ21009 9 6.75 6.75 11.1 810 100 13.5
AGQ21012 12 9 9 8.3 1,440 100 18
AGQ21024 24 18 18 5.0 4,800 120 36
Operating
Function
Part No. Coil Rating,
V DC
Pick-up
voltage,
V DC (max.)
(initial)
Drop-out
voltage,
V DC (min.)
(initial)
Nominal
operating
current,
mA (
±
10%)
Coil
resistance,
(
±
10%)
Nominal
operating
power,
mW
Max.
allowable
voltage,
V DC
Tube packing Tape and reel
packing
Single side
stable
AGQ200
1H AGQ200
1HZ 1.5 1.13 0.15 93.8 16 140 2.25
AGQ200
03 AGQ200
03Z 3 2.25 0.3 46.7 64.2 140 4.5
AGQ200
4H AGQ200
4HZ 4.5 3.38 0.45 31 145 140 6.75
AGQ200
06 AGQ200
06Z 6 4.5 0.6 23.3 257 140 9
AGQ200
09 AGQ200
09Z 9 6.75 0.9 15.5 579 140 13.5
AGQ200
12 AGQ200
12Z 12 9 1.2 11.7 1,028 140 18
AGQ200
24 AGQ200
24Z 24 18 2.4 9.6 2,504 230 28.8
GQ
131
: For each surface-mounted terminal variation, input the following letter.
A type: A, S type: S
1) Standard packing: 50 pcs.(tube), 900pcs. (tape and reel)in an inner package; 1,000 pcs.(tube), 1,800pcs. (tape and reel)in an outer package
2) Specified value of pick-up, drop-out, set and reset voltage is with the condition of square wave coil pulse.
Operating
Function
Part No. Coil Rating,
V DC Set voltage,
V DC (max.)
(initial)
Reset
voltage,
V DC (max.)
(initial)
Nominal
operating
current,
mA (
±
10%)
Coil
resistance,
(
±
10%)
Nominal
operating
power,
mW
Max.
allowable
voltage,
V DC
Tube packing Tape and reel
packing
1 coil
latching
AGQ210
1H AGQ210
1HZ 1.5 1.13 1.13 66.7 22.5 100 2.25
AGQ210
03 AGQ210
03Z 3 2.25 2.25 33.3 90 100 4.5
AGQ210
4H AGQ210
4HZ 4.5 3.38 3.38 22.2 202.5 100 6.75
AGQ210
06 AGQ210
06Z 6 4.5 4.5 16.7 360 100 9
AGQ210
09 AGQ210
09Z 9 6.75 6.75 11.1 810 100 13.5
AGQ210
12 AGQ210
12Z 12 9 9 8.3 1,440 100 18
AGQ210
24 AGQ210
24Z 24 18 18 5.0 4,800 120 36
DIMENSIONS
1. PC board terminal
10.60±0.3
.417±.012
0.40±0.1
.016±.004
2.20±0.15
.087±.006
2.20±0.15
.087±.006
3.20±0.15
.126±.006 3.50±0.3
.138±.012
5.20±0.2
.205±.008 7.20±0.3
.283±.012
0.20±0.1
.008±.004
5.08±0.15
.200±.006
PC board pattern
Tolerance:
±
0.1
±
.004
5.08
.200
2.20
.087
2.20
.087
3.20
.126
8-0.85 dia.
8-.033 dia.
Schematic (Bottom view)
Single side stable
(Deenergized condition) 1 coil latching
(Reset condition)
Direction indication
4321
5678
Direction indication
4321
5678
mm inch
2. Surface-mount terminal
1) A type 10.60±0.3
.417±.012
0.40±0.1
.016±.004
Max. 5.40
.213
8.40±0.3
.331±.012
3.20±0.15
.126±.006
2.20±0.15
.087±.006
2.20±0.15
.087±.006
7.20±0.3
.283±.012
0.20±0.1
.008±.004 5.08±0.15
.200±.006
Suggested mounting pad
Single side stable/
1 coil latching
3.20
.126
2.20
.087
2.20
.087
0.80
.031
2.66
.105 6.74
.265
1) S type 10.60±0.3
.417±.012
Max. 5.40
.213
0.40±0.1
.016±.004
3.20±0.15
.126±.006
2.20±0.15
.087±.006
2.20±0.15
.087±.006
7.20±0.3
.283±.012
7.20±0.3
.283±.012
0.20±0.1
.008±.004
5.08±0.15
.200±.006
Suggested mounting pad
Single side stable/
1 coil latching
Tolerance: ±0.1 ±.004
3.20
.126
2.20
.087
2.20
.087
0.80
.031
2.06
.081 6.14
.242
Schematic (Top view)
Single side stable
(Deenergized condition) 1 coil latcing
(Reset condition)
Direction indication
4321
5678
Direction indication
4321
5678
REFERENCE DATA
1. Max. switching capacity 2. Life curve
30 100
Contact voltage, V
1.0
0.3
DC resistive load
AC resistive load
Switching current, A
Switching current, A
No. of operations, × 104
0.2 0.4 0.6 0.8 1.0 1.2
100
50
30
40
20
10
0
DC 30V resistive load
AC 125V
resistive load
GQ
132
NOTES
1. Coil operating power
1) As a general rule, only a pure DC pow-
er supply should be used f or the coil drive .
2) T o ensure proper operation, the voltage
applied to both terminals of the coil should
be ±5% (at 20°C 68°F) the rated operating
voltage of the coil. Also, be a ware that the
pick-up and drop-out voltages will fluctu-
ate depending on the ambient tempera-
ture and operating conditions.
3) The ripple factor f or the voltage applied
to the coil should be less than 5%.
4) For set and reset latching relays, the
rated operating v oltage should be applied
to the coil for 10 ms or more.
2. Coil connection
When connecting coils, ref er to the wiring
diagram to prevent mis-operation or mal-
function.
3. External magnetic field
Since GQ relays are highly sensitive po-
larized rela ys , their char acteristics will be
affected by a strong external magnetic
field. Avoid using the rela y under that con-
dition.
4. Cleaning
In automatic cleaning, cleaning with the
boiling method is recommended. A v oid ul-
trasonic cleaning which subject the relay
to high frequency vibrations. It may cause
the contacts to stick.
lt is recommended that a fluorinated hy-
drocarbon or other alcoholic solvent be
used.
5. Packing style
1) The relay is packed in a tube with the
relay orientation mark on the left side, as
shown in the figure below.
2) Tape and reel packing
(A type)
(1)-1 Tape dimensions mm inch
(S type)
(1)-2 Tape dimensions
(2) Dimensions of plastic peel mm inch
6. Automatic insertion
To maintain the internal function of the re-
lay, the chucking pressure should not ex-
ceed the values below.
Chucking pressure in the direction A :
9.8 N {1 kgf} or less
Chucking pressure in the direction B :
9.8 N {1 kgf} or less
Chucking pressure in the direction C :
9.8 N {1 kgf} or less
Please chuck the portion.
Avoid chucking the center of the relay.
In addition, excessive chucking pressure
to the pinpoint of the rela y should be also
avoided.
Orientation (indicates PIN No.1)stripe
Stopper (green) Stopper (red)
Orientation (indicates PIN No.1)stripe
Stopper (green) Stopper (red)
Relay polarity bar
(Z type)
Tape coming out direction
General tolerance ±0.1 mm .004 inch
1.50 dia.
.059 dia. 4.00
.157 0.40
.016
1.75
.069
2.00dia.
.079dia.
2.0
.079
12.0
.472 9.0
.354
Max. 6.55
.256
24.0±0.3
.945±.012
11.1
.437
11.5
.453
+0.1
0
+.003
.0
GQ relays
Relay polarity bar
(Z type)
Tape coming out direction
General tolerance ±0.1 mm .004 inch
4.0
.157
0.40
.016
1.75
.069
2.00dia.
.079dia.
2.0
.079
12.0
.472 7.8
.307
Max. 6.55
.256
11.5
.453
1.50 dia.
.059 dia.
+0.1
0
+.003
.0
GQ relays
11.1
.437
24.0±0.3
.945±.012
21±0.8 dia.
.827±.031 dia.
13±0.2 dia.
.512±.008 dia.
24.4
.961+2
0
+.079
0 2.0±0.2
.079±.008
2.0±0.5
.079±.020
100±1 dia.
3.937±.039 dia.
330±2 dia.
12.992±.079 dia.
ACB
,
,,
,
,
For Cautions for Use, see Relay Technical Information (Page 48 to 76).
9/1/2000 All Rights Reserved, © Copyright Matsushita Electric Works, Ltd.
Go To Online Catalog