Semiconductor Components Industries, LLC, 2002
August, 2002 – Rev. 11 1Publication Order Number:
LM358/D
LM358, LM258, LM2904,
LM2904A, LM2904V,
NCV2904
Single Supply Dual
Operational Amplifiers
Utilizing the circuit designs perfected for Quad Operational
Amplifiers, these dual operational amplifiers feature low power drain,
a common mode input voltage range extending to ground/VEE, and
single supply or split supply operation. The LM358 series is
equivalent to one–half of an LM324.
These amplifiers have several distinct advantages over standard
operational amplifier types in single supply applications. They can
operate at supply voltages as low as 3.0 V or as high as 32 V, with
quiescent currents about one–fifth of those associated with the
MC1741 (on a per amplifier basis). The common mode input range
includes the negative supply, thereby eliminating the necessity for
external biasing components in many applications. The output voltage
range also includes the negative power supply voltage.
•Short Circuit Protected Outputs
•True Differential Input Stage
•Single Supply Operation: 3.0 V to 32 V (LM258/LM358)
3.0 V to 26 V (LM2904, A, V)
•Low Input Bias Currents
•Internally Compensated
•Common Mode Range Extends to Negative Supply
•Single and Split Supply Operation
•ESD Clamps on the Inputs Increase Ruggedness of the Device
without Affecting Operation
PDIP–8
N, AN, VN SUFFIX
CASE 626
1
8
SO–8
D, VD SUFFIX
CASE 751
1
8
PIN CONNECTIONS
VEE/Gnd
Inputs A
Inputs B
Output B
Output A VCC
–
–
+
+
1
2
3
4
8
7
6
5
(Top View)
See general marking information in the device marking
section on page 11 of this data sheet.
DEVICE MARKING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 10 of this data sheet.
ORDERING INFORMATION
Micro8
DMR2 SUFFIX
CASE 846A
1
8
http://onsemi.com
LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904
http://onsemi.com
2
Single Supply Split Supplies
VCC
VEE/Gnd
3.0 V to VCC(max)
1
2
VCC
1
2
VEE
1.5 V to VCC(max)
1.5 V to VEE(max)
Output
Bias Circuitry
Common to Both
Amplifiers
VCC
VEE/Gnd
Inputs
Q2
Q3 Q4
Q5
Q26
Q7
Q8
Q6
Q9
Q11
Q10
Q1 2.4 k
Q25
Q22
40 k
Q13
Q14
Q15
Q16
Q19
5.0 pF
Q18
Q17
Q20
Q21
2.0 k
Q24
Q23
Q12
25
Figure 1.
Figure 2. Representative Schematic Diagram
(One–Half of Circuit Shown)
LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904
http://onsemi.com
3
MAXIMUM RATINGS (TA = +25°C, unless otherwise noted.)
Rating Symbol LM258
LM358 LM2904, LM2904A
LM2904V, NCV2904 Unit
Power Supply Voltages Vdc
Single Supply VCC 32 26
Split Supplies VCC, VEE ±16 ±13
Input Differential Voltage Range (Note 1) VIDR ±32 ±26 Vdc
Input Common Mode Voltage Range (Note 2) VICR –0.3 to 32 –0.3 to 26 Vdc
Output Short Circuit Duration tSC Continuous
Junction Temperature TJ150 °C
Thermal Resistance, Junction–to–Air (Note 3) RJA 238 °C/W
Storage Temperature Range Tstg –55 to +125 °C
ESD Tolerance – Human Body Model (Note 4) – 2000 V
Operating Ambient Temperature Range TA°C
LM258 –25 to +85 –
LM358 0 to +70 –
LM2904/LM2904A – –40 to +105
LM2904V, NCV2904 (Note 5) ––40 to +125
1. Split Power Supplies.
2. For Supply Voltages less than 32 V for the LM258/358 and 26 V for the LM2904, A, V, the absolute maximum input voltage is equal to the
supply voltage.
3. RJA for Case 846A.
4. ESD data available upon request.
5.
NCV2904 is qualified for automotive use.
LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904
http://onsemi.com
4
ELECTRICAL CHARACTERISTICS (VCC = 5.0 V, VEE = Gnd, TA = 25°C, unless otherwise noted.)
LM258 LM358
Characteristic Symbol Min Typ Max Min Typ Max Unit
Input Offset Voltage
VCC = 5.0 V to 30 V (26 V for LM2904, V),
VIC = 0 V to VCC –1.7 V, VO 1.4 V, RS = 0 Ω
VIO mV
TA = 25°C – 2.0 5.0 – 2.0 7.0
TA = Thigh (Note 6) – – 7.0 – – 9.0
TA = Tlow (Note 6) – – 7.0 – – 9.0
Average Temperature Coefficient of Input Offset
Voltage ∆VIO/∆T – 7.0 – – 7.0 – µV/°C
TA = Thigh to Tlow (Note 6)
Input Offset Current IIO – 3.0 30 – 5.0 50 nA
TA = Thigh to Tlow (Note 6) – – 100 – – 150
Input Bias Current IIB – –45 –150 – –45 –250
TA = Thigh to Tlow (Note 6) – –50 –300 – –50 –500
Average Temperature Coefficient of Input Offset
Current ∆IIO/∆T – 10 – – 10 – pA/°C
TA = Thigh to Tlow (Note 6)
Input Common Mode Voltage Range (Note 7) ,
VCC = 30 V
(26 V for LM2904, V)
VICR 0 – 28.3 0 – 28.3 V
VCC = 30 V (26 V for LM2904, V),
TA = Thigh to Tlow 0 – 28 0 – 28
Differential Input Voltage Range VIDR – – VCC – – VCC V
Large Signal Open Loop Voltage Gain AVOL V/mV
RL = 2.0 kΩ, VCC = 15 V, For Large VO Swing, 50 100 – 25 100 –
TA = Thigh to Tlow (Note 6) 25 – – 15 – –
Channel Separation CS – –120 – – –120 – dB
1.0 kHz ≤ f ≤ 20 kHz, Input Referenced
Common Mode Rejection CMR 70 85 – 65 70 – dB
RS ≤ 10 kΩ
Power Supply Rejection PSR 65 100 – 65 100 – dB
Output Voltage–High Limit
TA = Thigh to Tlow (Note 6) VOH V
VCC = 5.0 V, RL = 2.0 kΩ, TA = 25°C 3.3 3.5 – 3.3 3.5 –
VCC = 30 V (26 V for LM2904, V), RL = 2.0 kΩ26 – – 26 – –
VCC = 30 V (26 V for LM2904, V), RL = 10 kΩ27 28 – 27 28 –
Output Voltage–Low Limit VOL – 5.0 20 – 5.0 20 mV
VCC = 5.0 V, RL = 10 kΩ,
TA = Thigh to Tlow (Note 6)
Output Source Current IO+20 40 – 20 40 – mA
VID = +1.0 V, VCC = 15 V
Output Sink Current IO–
VID = –1.0 V, VCC = 15 V 10 20 – 10 20 – mA
VID = –1.0 V, VO = 200 mV 12 50 – 12 50 – µA
Output Short Circuit to Ground (Note 8) ISC – 40 60 – 40 60 mA
Power Supply Current (Total Device)
TA = Thigh to Tlow (Note 6) ICC mA
VCC = 30 V (26 V for LM2904, V), VO = 0 V, RL = ∞– 1.5 3.0 – 1.5 3.0
VCC = 5 V, VO = 0 V, RL = ∞– 0.7 1.2 – 0.7 1.2
6. LM258: Tlow = –25°C, Thigh = +85°C LM358: Tlow = 0°C, Thigh = +70°C
LM2904/LM2904A: Tlow = –40°C, Thigh = +105°C LM2904V & NCV2904: Tlow = –40°C, Thigh = +125°C
NCV2904 is qualified for automotive use.
7. The input common mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3 V. The upper end of
the common mode voltage range is VCC –1.7 V.
8. Short circuits from the output to VCC can cause excessive heating and eventual destruction. Destructive dissipation can result from
simultaneous shorts on all amplifiers.
LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904
http://onsemi.com
5
ELECTRICAL CHARACTERISTICS (VCC = 5.0 V, VEE = Gnd, TA = 25°C, unless otherwise noted.)
LM2904 LM2904A LM2904V, NCV2904
Characteristic Symbol Min Typ Max Min Typ Max Min Typ Max Unit
Input Offset Voltage
VCC = 5.0 V to 30 V (26 V for LM2904, V),
VIC = 0 V to VCC –1.7 V, VO 1.4 V, RS = 0 Ω
VIO mV
TA = 25°C – 2.0 7.0 – 2.0 7.0 – – 7.0
TA = Thigh (Note 9) – – 10 – – 10 – – 13
TA = Tlow (Note 9) – – 10 – – 10 – – 10
Average Temperature Coefficient of Input Offset
Voltage ∆VIO/∆T – 7.0 – – 7.0 – – 7.0 – µV/°C
TA = Thigh to Tlow (Note 9)
Input Offset Current IIO – 5.0 50 – 5.0 50 – 5.0 50 nA
TA = Thigh to Tlow (Note 9) – 45 200 – 45 200 – 45 200
Input Bias Current IIB – –45 –250 – –45 –100 – –45 –250
TA = Thigh to Tlow (Note 9) – –50 –500 – –50 –250 – –50 –500
Average Temperature Coefficient of Input Offset
Current ∆IIO/∆T – 10 – – 10 – – 10 – pA/°C
TA = Thigh to Tlow (Note 9)
Input Common Mode Voltage Range (Note 10),
VCC = 30 V (26 V for LM2904, V) VICR 0 – 24.3 0 – 24.3 0 – 24.3 V
VCC = 30 V (26 V for LM2904, V),
TA = Thigh to Tlow 0 – 24 0 – 24 0 – 24
Differential Input Voltage Range VIDR – – VCC – – VCC – – VCC V
Large Signal Open Loop Voltage Gain AVOL V/mV
RL = 2.0 kΩ, VCC = 15 V, For Large VO Swing, 25 100 – 25 100 – 25 100 –
TA = Thigh to Tlow (Note 9) 15 – – 15 – – 15 – –
Channel Separation CS – –120 – – –120 – – –120 – dB
1.0 kHz ≤ f ≤ 20 kHz, Input Referenced
Common Mode Rejection CMR 50 70 – 50 70 – 50 70 – dB
RS ≤ 10 kΩ
Power Supply Rejection PSR 50 100 – 50 100 – 50 100 – dB
Output Voltage–High Limit
TA = Thigh to Tlow (Note 9) VOH V
VCC = 5.0 V, RL = 2.0 kΩ, TA = 25°C 3.3 3.5 – 3.3 3.5 – 3.3 3.5 –
VCC = 30 V (26 V for LM2904, V), RL = 2.0 kΩ22 – – 22 – – 22 – –
VCC = 30 V (26 V for LM2904, V), RL = 10 kΩ23 24 – 23 24 – 23 24 –
Output Voltage–Low Limit VOL – 5.0 20 – 5.0 20 – 5.0 20 mV
VCC = 5.0 V, RL = 10 kΩ,
TA = Thigh to Tlow (Note 9)
Output Source Current IO+20 40 – 20 40 – 20 40 – mA
VID = +1.0 V, VCC = 15 V
Output Sink Current IO–
VID = –1.0 V, VCC = 15 V 10 20 – 10 20 – 10 20 – mA
VID = –1.0 V, VO = 200 mV – – – – – – – – – µA
Output Short Circuit to Ground (Note 11) ISC – 40 60 – 40 60 – 40 60 mA
Power Supply Current (Total Device)
TA = Thigh to Tlow (Note 9) ICC mA
VCC = 30 V (26 V for LM2904, V), VO = 0 V,
RL = ∞– 1.5 3.0 – 1.5 3.0 – 1.5 3.0
VCC = 5 V, VO = 0 V, RL = ∞– 0.7 1.2 – 0.7 1.2 – 0.7 1.2
9. LM258: Tlow = –25°C, Thigh = +85°C LM358: Tlow = 0°C, Thigh = +70°C
LM2904/LM2904A: Tlow = –40°C, Thigh = +105°C LM2904V & NCV2904: Tlow = –40°C, Thigh = +125°C
NCV2904 is qualified for automotive use.
10.The input common mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3 V. The upper end of
the common mode voltage range is VCC –1.7 V.
11.Short circuits from the output to VCC can cause excessive heating and eventual destruction. Destructive dissipation can result from
simultaneous shorts on all amplifiers.
LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904
http://onsemi.com
6
CIRCUIT DESCRIPTION
The LM358 series is made using two internally
compensated, two–stage operational amplifiers. The first
stage of each consists of differential input devices Q20 and
Q18 with input buffer transistors Q21 and Q17 and the
differential to single ended converter Q3 and Q4. The first
stage performs not only the first stage gain function but also
performs the level shifting and transconductance reduction
functions. By reducing the transconductance, a smaller
compensation capacitor (only 5.0 pF) can be employed, thus
saving chip area. The transconductance reduction is
accomplished by splitting the collectors of Q20 and Q18.
Another feature of this input stage is that the input common
mode range can include the negative supply or ground, in
single supply operation, without saturating either the input
devices or the differential to single–ended converter. The
second stage consists of a standard current source load
amplifier stage.
Each amplifier is biased from an internal–voltage
regulator which has a low temperature coefficient thus
giving each amplifier good temperature characteristics as
well as excellent power supply rejection.
Figure 3. Large Signal Voltage
Follower Response
5.0 µs/DIV
1.0 V/DIV
VCC = 15 Vdc
RL = 2.0 kΩ
TA = 25°C
AVOL, OPEN LOOP VOLTAGE GAIN (dB)
V , INPUT VOLTAGE (V)
I
Figure 4. Input Voltage Range Figure 5. Large–Signal Open Loop Voltage Gain
18
16
14
12
10
8.0
6.0
4.0
2.0
0
20
0 2.0 4.0 6.0 8.0 10 12 14 16 18 20
VCC/VEE, POWER SUPPLY VOLTAGES (V)
120
100
80
60
40
20
0
-20
1.0 10 100 1.0 k 10 k 100 k 1.0 M
f, FREQUENCY (Hz)
Negative
Positive
VCC = 15 V
VEE = Gnd
TA = 25°C
LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904
http://onsemi.com
7
VOR, OUTPUT VOLTAGE RANGE (V )
pp
VO, OUTPUT VOLTAGE (mV)
Figure 6. Large–Signal Frequency Response Figure 7. Small Signal Voltage Follower
Pulse Response (Noninverting)
Figure 8. Power Supply Current versus
Power Supply Voltage Figure 9. Input Bias Current versus
Supply Voltage
14
12
10
8.0
6.0
4.0
2.0
0
1.0 10 100 1000
f, FREQUENCY (kHz)
550
500
450
400
350
300
250
200
00 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0
t, TIME (ms)
2.4
2.1
1.8
1.5
1.2
0.9
0.6
0.3
00 5.0 10 15 20 25 30 35
VCC, POWER SUPPLY VOLTAGE (V) VCC, POWER SUPPLY VOLTAGE (V)
90
80
70 0 2.0 4.0 6.0 8.0 10 12 14 16 18 20
I , POWER SUPPLY CURRENT (mA)
CC
I , INPUT BIAS CURRENT (nA)
IB
RL = 2.0 kΩ
VCC = 15 V
VEE = Gnd
Gain = -100
RI = 1.0 kΩ
RF = 100 kΩ
Input
Output
TA = 25°C
RL =
VCC = 30 V
VEE = Gnd
TA = 25°C
CL = 50 pF
LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904
http://onsemi.com
8
R1
2
1
R1
TBP
R1 + R2
R1
R1 + R2
1
eo
e1
e2
eo = C (1 + a + b) (e2 - e1)
R1 a R1
b R1
R
CR
-
+
1/2
LM358
+
-
-
+R
1/2
LM358
+
-
R1
R2
VO
Vref
Vin
VOH
VO
VOL
VinL = R1 (VOL - Vref)+ Vref
VinH =(VOH - Vref) + Vref
H = R1 + R2 (VOH - VOL)
R1
-
+
-
+
-
+
R
C
R2
R3
C1
100 k
R
C
R
C1 R2
100 k
Vin
Vref
Vref
Vref
Vref
Bandpass
Output
fo = 2 π RC
R1 = QR
R2 =
R3 = TN R2
C1 = 10 C
1
Notch Output
Vref =V
CC
Hysteresis
1/2
LM358
1/2
LM358
1
CR
VinL VinH
Vref
1/2
LM358
1/2
LM358 1/2
LM358 1/2
LM358
TBP = Center Frequency Gain
TN = Passband Notch Gain
R
C
R1
R2
R3
For:
-
+
fo
Q
TBP
TN
= 1.0 kHz
= 10
= 1
= 1
= 160 kΩ
= 0.001 µF
= 1.6 MΩ
= 1.6 MΩ
= 1.6 MΩ
Where:
MC1403
1/2
LM358
-
+
R1
VCC
VCC
VO
2.5 V
R2
50 k
10 k
Vref
Vref = VCC
2
5.0 k
RC
RC
+
1/2
LM358
-
VO
2 π RC
1
For: fo = 1.0 kHz
R = 16 kΩ
C = 0.01 µF
VO = 2.5 V (1 + R1
R2 )
1
VCC
fo =
Figure 10. Voltage Reference Figure 11. Wien Bridge Oscillator
Figure 12. High Impedance Differential Amplifier Figure 13. Comparator with Hysteresis
Figure 14. Bi–Quad Filter
LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904
http://onsemi.com
9
2
1
Vref =V
CC
1
2
Figure 15. Function Generator Figure 16. Multiple Feedback Bandpass Filter
For less than 10% error from operational amplifier.
If source impedance varies, filter may be preceded with voltage
follower buffer to stabilize filter parameters.
Where fo and BW are expressed in Hz.
Qo fo
BW < 0.1
Given: fo = center frequency
A(fo) = gain at center frequency
Choose value fo, C
Then: R3 = Q
π fo C
R3
R1 = 2 A(fo)
R1 R3
4Q2 R1 -R3
R2 =
+
-
+
-
-
+
Vref =V
CC
Vref
f = R1 + RC
4 CRf R1 R3 = R2 R1
R2 + R1
R2
300 k
75 k
R3
R1
C
Triangle Wave
Output
Square
Wave
Output
VCC
R3
R1
R2
Vref
Vin
CC
VO
CO
CO = 10 C
Rf
if,
1/2
LM358
Vref
1/2
LM358
1/2
LM358
100 k
LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904
http://onsemi.com
10
ORDERING INFORMATION
Device Package Operating Temperature Range Shipping
LM358D SO–8 98 Units/Rail
LM358DR2 SO–8
0°to +70°C
2500 Tape & Reel
LM358DMR2 Micro8 0°to +70°C4000 Tape & Reel
LM358N PDIP–8 50 Units/Rail
LM258D SO–8 98 Units/Rail
LM258DR2 SO–8
25°to +85°C
2500 Tape & Reel
LM258DMR2 Micro8 –25°to +85°C4000 Tape & Reel
LM258N PDIP–8 50 Units/Rail
LM2904D SO–8 98 Units/Rail
LM2904DR2 SO–8 2500 Tape & Reel
LM2904DMR2 Micro8
40°to +105°C
2500 Tape & Reel
LM2904N PDIP–8 –40°to +105°C50 Units/Rail
LM2904ADMR2 Micro8 4000 Tape & Reel
LM2904AN PDIP–8 50 Units/Rail
LM2904VD SO–8 98 Units/Rail
LM2904VDR2 SO–8 2500 Tape & Reel
LM2904VDMR2 Micro8 –40°to +125°C4000 Tape & Reel
LM2904VN PDIP–8 50 Units/Rail
NCV2904DR2* SO–8 2500 Tape & Reel
*NCV2904 is qualified for automotive use.
LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904
http://onsemi.com
11
PDIP–8
N SUFFIX
CASE 626
SO–8
D SUFFIX
CASE 751
MARKING DIAGRAMS
x = 2 or 3
A = Assembly Location
WL, L = Wafer Lot
YY, Y = Year
WW, W = Work Week
PDIP–8
AN SUFFIX
CASE 626
SO–8
VD SUFFIX
CASE 751
PDIP–8
VN SUFFIX
CASE 626
1
8
LMx58N
AWL
YYWW
1
8
LM2904AN
AWL
YYWW
1
8
LM2904N
AWL
YYWW
1
8
LM2904VN
AWL
YYWW
ALYW
LMx58
1
8
ALYW
2904
1
8
ALYW
2904V
1
8
Micro8
DMR2 SUFFIX
CASE 846A
x58
AYW
1
8
2904
AYW
1
8
904A
AYW
1
8
904V
AYW
1
8
*This marking diagram also applies to NCV2904DR2.
*
LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904
http://onsemi.com
12
PACKAGE DIMENSIONS
PDIP–8
N, AN, VN SUFFIX
CASE 626–05
ISSUE L
NOTES:
1. DIMENSION L TO CENTER OF LEAD WHEN
FORMED PARALLEL.
2. PACKAGE CONTOUR OPTIONAL (ROUND OR
SQUARE CORNERS).
3. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
14
58
F
NOTE 2 –A–
–B–
–T–
SEATING
PLANE
H
J
GDK
N
C
L
M
M
A
M
0.13 (0.005) B M
T
DIM MIN MAX MIN MAX
INCHESMILLIMETERS
A9.40 10.16 0.370 0.400
B6.10 6.60 0.240 0.260
C3.94 4.45 0.155 0.175
D0.38 0.51 0.015 0.020
F1.02 1.78 0.040 0.070
G2.54 BSC 0.100 BSC
H0.76 1.27 0.030 0.050
J0.20 0.30 0.008 0.012
K2.92 3.43 0.115 0.135
L7.62 BSC 0.300 BSC
M--- 10 --- 10
N0.76 1.01 0.030 0.040
SO–8
D, VD SUFFIX
CASE 751–07
ISSUE AA
SEATING
PLANE
1
4
58
N
J
X 45
K
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A AND B DO NOT INCLUDE MOLD
PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER
SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN
EXCESS OF THE D DIMENSION AT MAXIMUM
MATERIAL CONDITION.
6. 751-01 THRU 751-06 ARE OBSOLETE. NEW
STANDAARD IS 751-07
A
BS
D
H
C
0.10 (0.004)
DIM
A
MIN MAX MIN MAX
INCHES
4.80 5.00 0.189 0.197
MILLIMETERS
B3.80 4.00 0.150 0.157
C1.35 1.75 0.053 0.069
D0.33 0.51 0.013 0.020
G1.27 BSC 0.050 BSC
H0.10 0.25 0.004 0.010
J0.19 0.25 0.007 0.010
K0.40 1.27 0.016 0.050
M0 8 0 8
N0.25 0.50 0.010 0.020
S5.80 6.20 0.228 0.244
–X–
–Y–
G
M
Y
M
0.25 (0.010)
–Z–
Y
M
0.25 (0.010) Z SXS
M
LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904
http://onsemi.com
13
PACKAGE DIMENSIONS
Micro8
DMR2 SUFFIX
CASE 846A–02
ISSUE F
S
B
M
0.08 (0.003) A S
TDIM MIN MAX MIN MAX
INCHESMILLIMETERS
A2.90 3.10 0.114 0.122
B2.90 3.10 0.114 0.122
C--- 1.10 --- 0.043
D0.25 0.40 0.010 0.016
G0.65 BSC 0.026 BSC
H0.05 0.15 0.002 0.006
J0.13 0.23 0.005 0.009
K4.75 5.05 0.187 0.199
L0.40 0.70 0.016 0.028
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD FLASH,
PROTRUSIONS OR GATE BURRS. MOLD FLASH,
PROTRUSIONS OR GATE BURRS SHALL NOT
EXCEED 0.15 (0.006) PER SIDE.
4. DIMENSION B DOES NOT INCLUDE INTERLEAD
FLASH OR PROTRUSION. INTERLEAD FLASH OR
PROTRUSION SHALL NOT EXCEED 0.25 (0.010)
PER SIDE.
5. 846A-01 OBSOLETE, NEW STANDARD 846A-02.
–B–
–A–
D
K
G
PIN 1 ID
8 PL
0.038 (0.0015)
–T– SEATING
PLANE
C
HJL
LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904
http://onsemi.com
14
Notes
LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904
http://onsemi.com
15
Notes
LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904
http://onsemi.com
16
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make
changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any
particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all
liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be
validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others.
SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death
may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer.
PUBLICATION ORDERING INFORMATION
JAPAN: ON Semiconductor, Japan Customer Focus Center
2–9–1 Kamimeguro, Meguro–ku, Tokyo, Japan 153–0051
Phone: 81–3–5773–3850
Email: r14525@onsemi.com
ON Semiconductor Website: http://onsemi.com
For additional information, please contact your local
Sales Representative.
LM358/D
Literature Fulfillment:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303–675–2175 or 800–344–3860 Toll Free USA/Canada
Fax: 303–675–2176 or 800–344–3867 Toll Free USA/Canada
Email: ONlit@hibbertco.com
N. American Technical Support: 800–282–9855 Toll Free USA/Canada
