BB300 - BusBoard Prototype - Datasheet.Directory

BB300™, BB400™, BB400T™

– Plug-in Solderless BreadBoards

300 and 400 tie point solderless “plug-in” breadboards provide a quick way

to build and test circuits for experimentation or when learning electronics.

Completed projects can be moved to the SB300 and SB400/SB404 Solderable PC

BreadBoards to make them permanent.

BB300 Plug-in BreadBoard SB300 Solderable PC BreadBoard

BB300 – 300 tie point Solderless BreadBoard SB300 – 300 tie point

white ABS plastic with black legend Solderable PC BreadBoard

1 IC-Circuit Area, 300 tie-points

Size: 3.3 x 1.4 x 0.3in (84 x 35.5 x 8.5mm)

BB400 Plug-in BreadBoard SB400 Solderable PC BreadBoard

BB400T Transparent Plug-in BreadBoard

BB400 and BB400T – 400 tie point BreadBoard, SB400 – 400 tie point

with two power rails Solderable PC BreadBoard

ABS plastic with color legend, white or transparent

1 IC-Circuit Area (300 tie-points) plus 2 Distribution strips (100 tie-points)

Size: 3.3 x 2.1 x 0.3in (84 x 54.3 x 8.5mm)

BusBoard Prototype Systems - Built for designers

www.BusBoard.com sales@busboard.com BPS-DAT-(BB300+BB400)-0001 Rev 5 Datasheet.doc Page 1

Move your project

to SB400

or SB404

Move your project

to SB300

The BB400T transparent

breadboard is great for

beginners because they

can see the internal circuit

connections.

Note: The SB404 adds 4 mounting holes

Solderless Plug-in BreadBoards

Solderless BreadBoard Specifications

BB300 Body Material: White ABS Plastic with Black Printed Legend

BB400/BB830/BB1660 Body Material: White ABS Plastic with Color Printed Legend

BB400T/BB830T/BB1660T Body Material: Transparent ABS Plastic with Color Printed Legend

Hole Pitch/Style: 0.1" (2.54 mm), Square Wire Holes

ABS Heat Distortion Temperature: 84 C. (183 F.)

Spring Clip Contact: Phosphor Bronze with Plated Nickel Finish

Contact Life: 50,000 insertions

Rating: 36 Volts, 2 Amps

Insertion Wire Size: 21 to 26 AWG wire, or 0.025” Square post headers

0.016 to 0.028 inches diameter (0.4 to 0.7mm diameter)

Backing: Peelable adhesive tape for attaching to a surface.

Metal back plate provided with 830 tie point breadboards.

Metal Back Plate Thickness: 0.031 inches (0.8mm)

All BPS BreadBoards are Lead-Free and RoHS Compliant.

Internal Connections

BB300 BreadBoard

The BB300 breadboard tie-points are connected in

60 vertical columns (the green lines) with 5

connected holes in each. This is the circuit area.

When an integrated circuit is plugged into the

breadboard, each I.C. pin has a column.

There are no horizontal running connections on the

BB300.

BB400 BreadBoard

The BB400 and BB400T breadboards have 60

vertical columns in the circuit area (the green lines)

plus 4 “rails” or distribution strips for power and

ground running horizontally (the red and blue

lines).

A distribution strip can be used to carry a signal if

it is not needed for power or ground.

BusBoard Prototype Systems - Built for designers

www.BusBoard.com sales@busboard.com BPS-DAT-(BB300+BB400)-0001 Rev 5 Datasheet.doc Page 2

Solderless BreadBoard FAQ

Q: What circuit frequencies can I use with a plug-in solderless breadboard?

A: Due to large stray capacitance (from 2-25pF per contact point), the inductance of connections, and a

relatively high and not very reproducible contact resistance, solderless breadboards are limited to operate at

relatively low frequencies, usually less than 10 MHz, depending on the nature of the circuit. The relatively

high contact resistance can also be a problem for some DC and very low frequency circuits.

Source http://en.wikipedia.org/wiki/Breadboard

Higher frequency operation may be possible in some cases, depending upon the circuit requirements.

Note: Solderable PC BreadBoards, such as the BPS BR1, SB300, SB400, and SB404 will provide lower stray

capacitance and lower connection resistance which may allow higher frequency operation for some circuits.

For circuits sensitive to small changes in values, component adjustments may be needed when the circuit is

moved from a plug-in breadboard to a Solderable PC BreadBoard, due to these small differences.

Q: Can I plug DIL or SIL connector headers into the breadboard?

A: Yes. The square pin of a standard 0.1” spacing header is typically 0.025 inches wide. This is within the

0.016 to 0.028 inch diameter wire insertion size range recommended for the breadboard.

Solderless BreadBoard NSFAQ

Q: Who invented the solderless breadboard?

A: US Patent #203938 was awarded to Ronald J. Portugal of EI Instruments Inc. in 1971.

Q: Why is phosphorus added to the bronze used in the contacts?

A: Phosphor bronze is an alloy of copper with 3.5 to 10% of tin and a significant phosphorus content of up to

1%. The phosphorus is added as deoxidizing agent during melting.

These alloys are notable for their toughness, strength, low coefficient of friction, and fine grain. The

phosphorus also improves the fluidity of the molten metal and thereby improves the castability, and improves

mechanical properties by cleaning up the grain boundaries.

Source http://en.wikipedia.org/wiki/Phosphor_bronze

BusBoard Prototype Systems - Built for designers

www.BusBoard.com sales@busboard.com BPS-DAT-(BB300+BB400)-0001 Rev 5 Datasheet.doc Page 3