CAN4311115002451K - Yageo - Datasheet.Directory

HF R&D Print date 01/12/13 Preliminary internal use only

Long Shape

Aug. 6, 01

Multilayer Ceramic Antenna

for Bluetooth (ISM Band 2. 45GHz) 4311 115 00245/260/270

Grant Lin/Cliff 2001-08-06

Page 1 sheet 190-1

A4

spec.doc Phycomp Taiwan Ltd.

MULTILAYER CERAMIC ANTENNA

FOR BLUETOOTH & WLAN IEEE 802.11b (2.45G Hz ISM Band)

(Long Shape)

Product Specification1 (Preliminary)

QUICK REFERENCE DATA

Dimension 8* 3.5 * 0.9 mm

Central Frequency* 2.45 GHz

Bandwidth >100 MHz

Gain 0dBi max

VSWR 2.0 max

Polarization Linear

Azimuth Omni-directional

Impedance 50Ω

Operating Temperature -55~125 oC

Termination Ni/Sn (Environmentally-Friendly Leadless)

Resistance to soldering heat 260oC, 10 sec.

Maximum Power 1W

* Three types of antenna are available for central frequency adjustment (type 245, type 260, type 270)

Special Environmental Concerns- Green Products Design: The foil making process is using

environmentally-friendly aqueous solvent technology. Termination is lead free (Pb free) and

packing materials can be re-cycled

1 All the technical data and information contained herein are subject to change without priot notice

HF R&D Print date 01/12/13 Preliminary internal use only

Long Shape

Aug. 6, 01

Multilayer Ceramic Antenna

for Bluetooth (ISM Band 2. 45GHz) 4311 115 00245/260/270

Grant Lin/Cliff 2001-08-06

Page 2 sheet 190-2

A4

spec.doc Phycomp Taiwan Ltd.

APPLICATION

DIMENSIONAL DATA

Figure Dimension Port

L

W

T

F

s1

C

F

s1

L

W

T

F

s1

C

F

s1

L

W

T

F

C

S1

8±0.25 mm

3.5±0.2 mm

0.9±0.2 mm

1.25±0.25 mm

0.5±0.3 mm

1.25±0.25 mm

-

Feed Termination

-

NC Solder Termination

6mm

50Ohm Transmission Line

(by Microstrip Line or Coplanar Waveguide)

Ground plane(back side)

Antenna

Bluetooth

module or other

RF Module

2mm

8mm

Suggested Layout

Cleanance

HF R&D Print date 01/12/13 Preliminary internal use only

Long Shape

Aug. 6, 01

Multilayer Ceramic Antenna

for Bluetooth (ISM Band 2. 45GHz) 4311 115 00245/260/270

Grant Lin/Cliff 2001-08-06

Page 3 sheet 190-3

A4

spec.doc Phycomp Taiwan Ltd.

SOLDER LAND PATTERN

Figure Dimensions Remark

CC CC

L

CC C

C

FF S1

L

F

C

S1

9 ± 0.10 mm

1.40 ± 0.10 mm

0.90 ± 0.10 mm

1.40 ± 0.10 mm

Feed Pad

NC Mount Pad

Radiation Pattern Polar plot

E Plane

H Plane

HF R&D Print date 01/12/13 Preliminary internal use only

Long Shape

Aug. 6, 01

Multilayer Ceramic Antenna

for Bluetooth (ISM Band 2. 45GHz) 4311 115 00245/260/270

Grant Lin/Cliff 2001-08-06

Page 4 sheet 190-4

A4

spec.doc Phycomp Taiwan Ltd.

STANDARD TEST BOARD FOR SWR

(Note: Only for SWR Measurement, not for suggested layout)

5 mm

50 ohm transmission line

15 mm Material:FR4

PCB

0.8 mm

1.2 mm

23 mm

SMA

2.6mm

HF R&D Print date 01/12/13 Preliminary internal use only

Long Shape

Aug. 6, 01

Multilayer Ceramic Antenna

for Bluetooth (ISM Band 2. 45GHz) 4311 115 00245/260/270

Grant Lin/Cliff 2001-08-06

Page 5 sheet 190-5

A4

spec.doc Phycomp Taiwan Ltd.

RELIABILITY DATA (Reference to IEC Specification)

IEC

384-10/

CECC 32

100

CLAUSE

IEC

60068-2

TEST

METHOD

TEST

PROCEDURE

REQUIREMENTS

4.4 Mounting The antenna can be

mounted on printed-

circuit boards or ceramic

substrates by applying

wave soldering, reflow

soldering (including

vapour phase soldering)

or conductive adhesive

No visible damage

4.5 Visual inspection

and dimension

check

Any applicable method

using ×

××

× 10

magnification

In accordance with

specification (chip

off 4mm)

4.6.1 Antenna Frequency = 2.45 GHz;

at 20 oC

Standard test board

in page 4

4.8 Adhesion A force of 3 N applied

for 10 s to the line

joining the terminations

and in a plane parallel to

the substrate

No visible damage

Bond strength of

plating on end face

Mounted in accordance

with CECC 32 100,

paragraph 4.4

No visible damage 4.9

Conditions: bending 0.5

mm at a rate of 1mm/s,

radius jig. 340 mm,

2mm warp on FR4

board of 90 mm length

No visible damage

4.10 20(Tb) Resistance to

soldering heat

260 ± 5 °C for 10 ± 0.5 s

in a static solder bath

The terminations

shall be well tinned

after recovery and

Central Freq. Change

± 6%

HF R&D Print date 01/12/13 Preliminary internal use only

Long Shape

Aug. 6, 01

Multilayer Ceramic Antenna

for Bluetooth (ISM Band 2. 45GHz) 4311 115 00245/260/270

Grant Lin/Cliff 2001-08-06

Page 6 sheet 190-6

A4

spec.doc Phycomp Taiwan Ltd.

IEC

384-10/

CECC 32

100

CLAUSE

IEC

60068-2

TEST

METHOD

TEST

PROCEDURE

REQUIREMENTS

Resistance to

leaching

260 ± 5 °C for 30 ± 1 s

in a static solder bath

Using visual

enlargement of ×

××

× 10,

dissolution of the

termination shall not

exceed 10%

4.11 20(Ta) Solderability Zero hour test, and test

after storage (20 to 24

months) in original

atmosphere; un-mounted

chips completely

immersed for 2 ± 0.5 s

in 235 ± 5°C.

The termination must

be well tinned, at

least 75% is well

tinned at termination

4.12 4(Na) Rapid change of

temperature

-55 °C (30 minutes) to

+125 °C (30 minutes);

100 cycles

No visible damage

Central Freq. Change

± 6%

4.14 3(Ca) Damp heat

500 ± 12 hours at 60 °C;

90 to 95 % RH

No visible damage

2 hours recovery

Central Freq. Change

± 6%

4.15 Endurance

500 ± 12 hours at 125

°C;

No visible damage

2 hours recovery

Central Freq. Change

± 6%

HF R&D Print date 01/12/13 Preliminary internal use only

Long Shape

Aug. 6, 01

Multilayer Ceramic Antenna

for Bluetooth (ISM Band 2. 45GHz) 4311 115 00245/260/270

Grant Lin/Cliff 2001-08-06

Page 7 sheet 190-7

A4

spec.doc Phycomp Taiwan Ltd.

ORDERING INFORMATION: Method I- by 12NC Ordering Code

The antennas may be ordered by using the 12 NC ordering code. These code numbers can be

determined by the following rules:

4311 1 15 00 245

F C M S T A

F. Family Code

43 = Antenna

C. Packing Type Code

11 = 180 mm/ 7" blister (1000pcs) , 12 = 330 mm/13" blister (4000 pcs)

13 = Bulk (1000 pcs)

M. Materials Code

1 = High Frequency Material

S. Size Code

15 = 8 * 3.5 * 0.9 mm

T. Tolerance

00 = 100 M Hz Band Width

A. Working Frequency (three types of antenna are available)

245 = 2.45 GHz Type 245

260 = (2.45+0.15) GHz * Intention for shift up 150MHz Type 260

270 = (2.45+0.25) GHz * Intention for shift up 250MHz Type 270

Example: 12NC 4311 111 00245

Product description: Antenna (43) by 180 mm blister (11) of High

Frequency Material (1), Size 7.35*5.5*1.3 mm (1);

Tolerance (00) of 100 MHz (VSWR<2)

Working Frequency (245) = 2.45G Hz

ORDERING INFORMATION: Method II- by Clear Text Code

The antennas may be ordered by using the 16-digit clear text ordering code. These code numbers

can be determined by the following rules:

AN2450000708031K (Clear Text Code Example)

AN 2450 00 07 0803 1 K

Product Central Freq. Bandwidth Material Size Quantities Packing

AN=

Antenna

2450=2.45GHz

2600=2.60GHz

2700=2.70GHz

00= >100MHz

07=K7

0803=8*3.5*

0.9 mm

1 = 1K

4 = 4K

K=7" plastic

F =13" plastic

B = Bulk