ISO2-CMOS MT8870D/MT8870D-1 Integrated DTMF Receiver Features * * * * * * * * ISSUE 5 Complete DTMF Receiver Low power consumption Internal gain setting amplifier Adjustable guard time Central office quality Power-down mode Inhibit mode Backward compatible with MT8870C/MT8870C-1 Ordering Information MT8870DE/DE-1 18 Pin Plastic DIP MT8870DS/DS-1 18 Pin SOIC MT8870DN/DN-1 20 Pin SSOP -40 C to +85 C Description The MT8870D/MT8870D-1 is a complete DTMF receiver integrating both the bandsplit filter and digital decoder functions. The filter section uses switched capacitor techniques for high and low group filters; the decoder uses digital counting techniques to detect and decode all 16 DTMF tonepairs into a 4-bit code. External component count is minimized by on chip provision of a differential input amplifier, clock oscillator and latched three-state bus interface. Applications * * * * * * * Receiver system for British Telecom (BT) or CEPT Spec (MT8870D-1) Paging systems Repeater systems/mobile radio Credit card systems Remote control Personal computers Telephone answering machine VDD PWDN March 1997 VSS VRef Bias Circuit INH VRef Buffer Q1 Chip Chip Power Bias IN + High Group Filter Dial Tone Filter IN - Digital Detection Algorithm Code Converter and Latch Q2 Zero Crossing Detectors Q3 Low Group Filter GS Q4 to all Chip Clocks OSC1 OSC2 St GT St/GT Steering Logic ESt STD TOE Figure 1 - Functional Block Diagram 4-11 MT8870D/MT8870D-1 IN+ INGS VRef INH PWDN OSC1 OSC2 VSS 1 2 3 4 5 6 7 8 9 18 17 16 15 14 13 12 11 10 ISO2-CMOS VDD St/GT ESt StD Q4 Q3 Q2 Q1 TOE IN+ INGS VRef INH PWDN NC OSC1 OSC2 VSS 1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 VDD St/GT ESt StD NC Q4 Q3 Q2 Q1 TOE 20 PIN SSOP 18 PIN PLASTIC DIP/SOIC Figure 2 - Pin Connections Pin Description Pin # Name Description 18 20 1 1 IN+ Non-Inverting Op-Amp (Input). 2 2 IN- Inverting Op-Amp (Input). 3 3 GS Gain Select. Gives access to output of front end differential amplifier for connection of feedback resistor. 4 4 VRef Reference Voltage (Output). Nominally VDD/2 is used to bias inputs at mid-rail (see Fig. 6 and Fig. 10). 5 5 INH Inhibit (Input). Logic high inhibits the detection of tones representing characters A, B, C and D. This pin input is internally pulled down. 6 6 PWDN Power Down (Input). Active high. Powers down the device and inhibits the oscillator. This pin input is internally pulled down. 7 8 OSC1 Clock (Input). 8 9 OSC2 Clock (Output). A 3.579545 MHz crystal connected between pins OSC1 and OSC2 completes the internal oscillator circuit. 9 10 VSS Ground (Input). 0V typical. 10 11 TOE Three State Output Enable (Input). Logic high enables the outputs Q1-Q4. This pin is pulled up internally. 11- 1214 15 Q1-Q4 Three State Data (Output). When enabled by TOE, provide the code corresponding to the last valid tone-pair received (see Table 1). When TOE is logic low, the data outputs are high impedance. 15 17 StD Delayed Steering (Output).Presents a logic high when a received tone-pair has been registered and the output latch updated; returns to logic low when the voltage on St/GT falls below VTSt. 16 18 ESt Early Steering (Output). Presents a logic high once the digital algorithm has detected a valid tone pair (signal condition). Any momentary loss of signal condition will cause ESt to return to a logic low. 17 19 St/GT 18 20 VDD Positive power supply (Input). +5V typical. 7, 16 NC No Connection. 4-12 Steering Input/Guard time (Output) Bidirectional. A voltage greater than VTSt detected at St causes the device to register the detected tone pair and update the output latch. A voltage less than VTSt frees the device to accept a new tone pair. The GT output acts to reset the external steering time-constant; its state is a function of ESt and the voltage on St. ISO2-CMOS MT8870D/MT8870D-1 Functional Description VDD The MT8870D/MT8870D-1 monolithic DTMF receiver offers small size, low power consumption and high performance. Its architecture consists of a bandsplit filter section, which separates the high and low group tones, followed by a digital counting section which verifies the frequency and duration of the received tones before passing the corresponding code to the output bus. Filter Section C VDD St/GT vc ESt R StD MT8870D/ MT8870D-1 tGTA=(RC)In(VDD/VTSt) tGTP=(RC)In[VDD/(VDD-VTSt)] Separation of the low-group and high group tones is achieved by applying the DTMF signal to the inputs of two sixth-order switched capacitor bandpass filters, the bandwidths of which correspond to the low and high group frequencies. The filter section also incorporates notches at 350 and 440 Hz for exceptional dial tone rejection (see Figure 3). Each filter output is followed by a single order switched capacitor filter section which smooths the signals prior to limiting. Limiting is performed by high-gain comparators which are provided with hysteresis to prevent detection of unwanted low-level signals. The outputs of the comparators provide full rail logic swings at the frequencies of the incoming DTMF signals. providing tolerance to small frequency deviations and variations. This averaging algorithm has been developed to ensure an optimum combination of immunity to talk-off and tolerance to the presence of interfering frequencies (third tones) and noise. When the detector recognizes the presence of two valid tones (this is referred to as the "signal condition" in some industry specifications) the "Early Steering" (ESt) output will go to an active state. Any subsequent loss of signal condition will cause ESt to assume an inactive state (see "Steering Circuit"). Decoder Section Steering Circuit Following the filter section is a decoder employing digital counting techniques to determine the frequencies of the incoming tones and to verify that they correspond to standard DTMF frequencies. A complex averaging algorithm protects against tone simulation by extraneous signals such as voice while Before registration of a decoded tone pair, the receiver checks for a valid signal duration (referred to as character recognition condition). This check is performed by an external RC time constant driven by ESt. A logic high on ESt causes vc (see Figure 4) to rise as the capacitor discharges. Provided signal Figure 4 - Basic Steering Circuit 0 PRECISE DIAL TONES 10 X=350 Hz Y=440 Hz DTMF TONES 20 A=697 Hz B=770 Hz C=852 Hz D=941 Hz E=1209 Hz F=1336 Hz G=1477 Hz H=1633 Hz ATTENUATION (dB) 30 40 50 X Y 1kHz A B C D E FREQUENCY (Hz) F G H Figure 3 - Filter Response 4-13 MT8870D/MT8870D-1 ISO2-CMOS condition is maintained (ESt remains high) for the validation period (tGTP), vc reaches the threshold (VTSt) of the steering logic to register the tone pair, latching its corresponding 4-bit code (see Table 1) into the output latch. At this point the GT output is activated and drives vc to VDD. GT continues to drive high as long as ESt remains high. Finally, after a short delay to allow the output latch to settle, the delayed steering output flag (StD) goes high, signalling that a received tone pair has been registered. The contents of the output latch are made available on the 4-bit output bus by raising the three state control input (TOE) to a logic high. The steering circuit works in reverse to validate the interdigit pause between signals. Thus, as well as rejecting signals too short to be considered valid, the receiver will tolerate signal interruptions (dropout) too short to be considered a valid pause. This facility, together with the capability of selecting the steering time constants externally, allows the designer to tailor performance to meet a wide variety of system requirements. Guard Time Adjustment In many situations not requiring selection of tone duration and interdigital pause, the simple steering circuit shown in Figure 4 is applicable. Component values are chosen according to the formula: tREC=tDP+tGTP tID=tDA+tGTA The value of tDP is a device parameter (see Figure 11) and tREC is the minimum signal duration to be recognized by the receiver. A value for C of 0.1 F is tGTP=(RPC1)In[VDD/(VDD-VTSt)] VDD tGTA=(R1C1)In(VDD/VTSt) C1 RP=(R1R2)/(R1+R2) St/GT R1 R2 ESt a) decreasing tGTP; (tGTPtGTA) Figure 5 - Guard Time Adjustment 4-14 Digit TOE INH ESt Q4 Q3 Q2 Q1 ANY L X H Z Z Z Z 1 H X H 0 0 0 1 2 H X H 0 0 1 0 3 H X H 0 0 1 1 4 H X H 0 1 0 0 5 H X H 0 1 0 1 6 H X H 0 1 1 0 7 H X H 0 1 1 1 8 H X H 1 0 0 0 9 H X H 1 0 0 1 0 H X H 1 0 1 0 * H X H 1 0 1 1 # H X H 1 1 0 0 A H L H 1 1 0 1 B H L H 1 1 1 0 C H L H 1 1 1 1 D H L H 0 0 0 0 A H H L B H H L C H H L D H H L undetected, the output code will remain the same as the previous detected code Table 1. Functional Decode Table L=LOGIC LOW, H=LOGIC HIGH, Z=HIGH IMPEDANCE X = DON`T CARE recommended for most applications, leaving R to be selected by the designer. Different steering arrangements may be used to select independently the guard times for tone present (tGTP) and tone absent (tGTA). This may be necessary to meet system specifications which place both accept and reject limits on both tone duration and interdigital pause. Guard time adjustment also allows the designer to tailor system parameters such as talk off and noise immunity. Increasing tREC improves talk-off performance since it reduces the probability that tones simulated by speech will maintain signal condition long enough to be registered. Alternatively, a relatively short tREC with a long tDO would be appropriate for extremely noisy environments where fast acquisition time and immunity to tone drop-outs are required. Design information for guard time adjustment is shown in Figure 5. ISO2-CMOS MT8870D/MT8870D-1 Power-down and Inhibit Mode A logic high applied to pin 6 (PWDN) will power down the device to minimize the power consumption in a standby mode. It stops the oscillator and the functions of the filters. C1 R1 MT8870D/ MT8870D-1 IN+ + IN- Inhibit mode is enabled by a logic high input to the pin 5 (INH). It inhibits the detection of tones representing characters A, B, C, and D. The output code will remain the same as the previous detected code (see Table 1). C2 R4 R5 R3 R2 Differential Input Configuration The input arrangement of the MT8870D/MT8870D-1 provides a differential-input operational amplifier as well as a bias source (VRef) which is used to bias the inputs at mid-rail. Provision is made for connection of a feedback resistor to the op-amp output (GS) for adjustment of gain. In a single-ended configuration, the input pins are connected as shown in Figure 10 with the op-amp connected for unity gain and VRef biasing the input at 1/2VDD. Figure 6 shows the differential configuration, which permits the adjustment of gain with the feedback resistor R5. GS VRef Differential Input Amplifier C1=C2=10 nF All resistors are 1% tolerance. R1=R4=R5=100 k All capacitors are 5% tolerance. R2=60k, R3=37.5 k R3= R2R5 R2+R5 VOLTAGE GAIN (Av diff)= R5 R1 INPUT IMPEDANCE (ZINDIFF) = 2 R12+ 2 1 c Crystal Oscillator Figure 6 - Differential Input Configuration The internal clock circuit is completed with the addition of an external 3.579545 MHz crystal and is normally connected as shown in Figure 10 (SingleEnded Input Configuration). However, it is possible to configure several MT8870D/MT8870D-1 devices employing only a single oscillator crystal. The oscillator output of the first device in the chain is coupled through a 30 pF capacitor to the oscillator input (OSC1) of the next device. Subsequent devices are connected in a similar fashion. Refer to Figure 7 for details. The problems associated with unbalanced loading are not a concern with the arrangement shown, i.e., precision balancing capacitors are not required. To OSC1 of next MT8870D/MT8870D-1 C X-tal OSC1 OSC2 OSC2 OSC1 C C=30 pF X-tal=3.579545 MHz Figure 7 - Oscillator Connection Parameter Unit Resonator R1 Ohms 10.752 L1 mH .432 C1 pF 4.984 C0 pF 37.915 Qm - 896.37 f % 0.2% Table 2. Recommended Resonator Specifications Note: Qm=quality factor of RLC model, i.e., 1/2R1C1. 4-15 ISO2-CMOS MT8870D/MT8870D-1 Applications RECEIVER SYSTEM FOR BRITISH TELECOM SPEC POR 1151 The circuit shown in Fig. 9 illustrates the use of MT8870D-1 device in a typical receiver system. BT Spec defines the input signals less than -34 dBm as the non-operate level. This condition can be attained by choosing a suitable values of R1 and R2 to provide 3 dB attenuation, such that -34 dBm input signal will correspond to -37 dBm at the gain setting pin GS of MT8870D-1. As shown in the diagram, the component values of R3 and C2 are the guard time requirements when the total component tolerance is 6%. For better performance, it is recommended to use the non-symmetric guard time circuit in Fig. 8. tGTP=(RPC1)In[VDD/(VDD-VTSt)] tGTA=(R1C1)In(VDD/VTSt) RP=(R1R2)/(R1+R2) VDD C1 St/GT R1 ESt R2 Notes: R1=368K 1% R2=2.2M 1% C1=100nF 5% Figure 8 - Non-Symmetric Guard Time Circuit VDD C1 DTMF Input R1 R2 MT8870D-1 IN+ VDD IN- St/GT ESt StD Q4 Q3 Q2 Q1 TOE GS VRef INH PWDN X1 OSC 1 OSC 2 VSS C2 R3 NOTES: R1 = 102K 1% R2 = 71.5K 1% R3 = 390K 1 % C1,C2 = 100 nF 5% X1 = 3.579545 MHz 0.1% VDD = 5.0V 5% Figure 9 - Single-Ended Input Configuration for BT or CEPT Spec 4-16 ISO2-CMOS MT8870D/MT8870D-1 Absolute Maximum Ratings Parameter Symbol 1 DC Power Supply Voltage 2 Voltage on any pin VI 3 Current at any pin (other than supply) II 4 Storage temperature 5 Package power dissipation Min Max Units 7 V VDD+0.3 V 10 mA +150 C 500 mW VDD VSS-0.3 TSTG -65 PD Exceeding these values may cause permanent damage. Functional operation under these conditions is not implied. Derate above 75 C at 16 mW / C. All leads soldered to board. Recommended Operating Conditions - Voltages are with respect to ground (VSS) unless otherwise stated. Parameter Sym Min Typ Max Units VDD 4.75 5.0 5.25 V -40 +85 C 1 DC Power Supply Voltage 2 Operating Temperature TO 3 Crystal/Clock Frequency fc 3.579545 MHz 4 Crystal/Clock Freq.Tolerance fc 0.1 % Test Conditions Typical figures are at 25C and are for design aid only: not guaranteed and not subject to production testing. DC Electrical Characteristics - VDD=5.0V 5%, VSS=0V, -40C TO +85C, unless otherwise stated. Typ Max Units IDDQ 10 25 A Operating supply current IDD 3.0 9.0 mA Power consumption PO 15 4 High level input VIH 5 Low level input voltage VIL Input leakage current IIH/IIL 0.1 Pull up (source) current ISO 7.5 Pull down (sink) current ISI 15 9 Input impedance (IN+, IN-) RIN 10 10 Steering threshold voltage VTSt 11 Low level output voltage VOL High level output voltage VOH VDD-0.03 Output low (sink) current IOL 1.0 2.5 mA VOUT=0.4 V Output high (source) current IOH 0.4 0.8 mA VOUT=4.6 V VRef output voltage VRef 2.3 2.5 1 2 3 6 7 8 12 13 14 15 S U P P L Y I N P U T S O U T P U T S Characteristics Sym Standby supply current Min mW 3.5 2.4 PWDN=VDD fc=3.579545 MHz V VDD=5.0V V VDD=5.0V A VIN=VSS or VDD 20 A TOE (pin 10)=0, VDD=5.0V 45 A INH=5.0V, PWDN=5.0V, VDD=5.0V M @ 1 kHz 1.5 2.2 Test Conditions 2.5 V VDD = 5.0V VSS+0.03 V No load V No load 2.7 V No load, VDD = 5.0V 16 VRef output resistance ROR 1 k Typical figures are at 25C and are for design aid only: not guaranteed and not subject to production testing. 4-17 ISO2-CMOS MT8870D/MT8870D-1 Operating Characteristics - VDD=5.0V5%, VSS=0V, -40C TO +85C ,unless otherwise stated. Gain Setting Amplifier Characteristics Sym Min Max Units 100 nA Test Conditions VSS VIN VDD 1 Input leakage current IIN 2 Input resistance RIN 3 Input offset voltage VOS 4 Power supply rejection PSRR 50 dB 1 kHz 5 Common mode rejection CMRR 40 dB 0.75 V VIN 4.25 V biased at VRef =2.5 V 6 DC open loop voltage gain AVOL 32 dB 7 Unity gain bandwidth fC 0.30 MHz 8 Output voltage swing VO 4.0 Vpp 9 Maximum capacitive load (GS) CL 100 pF 10 Resistive load (GS) RL 50 k 11 Common mode range 10 Characteristics VCM Sym M 25 2.5 MT8870D AC Electrical Characteristics - mV Vpp Load 100 k to VSS @ GS No Load VDD=5.0V 5%, VSS=0V, -40C TO +85C , using Test Circuit shown in Figure 10. Min Typ Max Units Notes* -29 +1 dBm 1,2,3,5,6,9 27.5 869 mVRMS 1,2,3,5,6,9 1 Valid input signal levels (each tone of composite signal) 2 Negative twist accept 8 dB 2,3,6,9,12 3 Positive twist accept 8 dB 2,3,6,9,12 4 Frequency deviation accept 1.5% 2 Hz 2,3,5,9 5 Frequency deviation reject 3.5% 2,3,5,9 6 Third tone tolerance -16 dB 2,3,4,5,9,10 7 Noise tolerance -12 dB 2,3,4,5,7,9,10 +22 dB 2,3,4,5,8,9,11 8 Typ Dial tone tolerance Typical figures are at 25 C and are for design aid only: * NOTES not guaranteed and not subject to production testing. 1. dBm= decibels above or below a reference power of 1 mW into a 600 ohm load. 2. Digit sequence consists of all DTMF tones. 3. Tone duration= 40 ms, tone pause= 40 ms. 4. Signal condition consists of nominal DTMF frequencies. 5. Both tones in composite signal have an equal amplitude. 6. Tone pair is deviated by 1.5 % 2 Hz. 7. Bandwidth limited (3 kHz ) Gaussian noise. 8. The precise dial tone frequencies are (350 Hz and 440 Hz) 2 %. 9. For an error rate of better than 1 in 10,000. 10. Referenced to lowest level frequency component in DTMF signal. 11. Referenced to the minimum valid accept level. 12. Guaranteed by design and characterization. 4-18 ISO2-CMOS MT8870D-1 AC Electrical Characteristics Characteristics VDD=5.0V5%, VSS=0V, -40C TO +85C , using Test Circuit shown in Figure 10. Min Typ Max Units Notes* -31 +1 dBm 21.8 869 mVRMS Tested at VDD=5.0V 1,2,3,5,6,9 1 Valid input signal levels (each tone of composite signal) 2 Input Signal Level Reject 3 Negative twist accept 8 dB 2,3,6,9,13 4 Positive twist accept 8 dB 2,3,6,9,13 5 Frequency deviation accept 1.5% 2 Hz 2,3,5,9 6 Frequency deviation reject 3.5% 2,3,5,9 7 Third zone tolerance 8 Noise tolerance 9 Sym MT8870D/MT8870D-1 Dial tone tolerance Typical figures are at 25 C and are for design aid only: -37 dBm 10.9 mVRMS Tested at VDD=5.0V 1,2,3,5,6,9 -18.5 dB 2,3,4,5,9,12 -12 dB 2,3,4,5,7,9,10 +22 dB 2,3,4,5,8,9,11 not guaranteed and not subject to production testing. * NOTES 1. dBm= decibels above or below a reference power of 1 mW into a 600 ohm load. 2. Digit sequence consists of all DTMF tones. 3. Tone duration= 40 ms, tone pause= 40 ms. 4. Signal condition consists of nominal DTMF frequencies. 5. Both tones in composite signal have an equal amplitude. 6. Tone pair is deviated by 1.5 % 2 Hz. 7. Bandwidth limited (3 kHz ) Gaussian noise. 8. The precise dial tone frequencies are (350 Hz and 440 Hz) 2 %. 9. For an error rate of better than 1 in 10,000. 10. Referenced to lowest level frequency component in DTMF signal. 11. Referenced to the minimum valid accept level. 12. Referenced to Fig. 10 input DTMF tone level at -25dBm (-28dBm at GS Pin) interference frequency range between 480-3400Hz. 13. Guaranteed by design and characterization. 4-19 ISO2-CMOS MT8870D/MT8870D-1 AC Electrical Characteristics - VDD=5.0V5%, VSS=0V, -40C To +85C , using Test Circuit shown in Figure 10. Sym Min Typ Max Units Tone present detect time tDP 5 11 14 ms Note 1 Tone absent detect time tDA 0.5 4 8.5 ms Note 1 40 ms Note 2 ms Note 2 ms Note 2 ms Note 2 Characteristics 1 2 3 4 5 T I M I N G Tone duration accept tREC Tone duration reject tREC 20 Interdigit pause accept tID 6 Interdigit pause reject tDO 7 Propagation delay (St to Q) tPQ 8 11 s TOE=VDD 16 s TOE=VDD 8 9 10 11 12 13 16 17 20 O U T P U T S Propagation delay (St to StD) tPStD 12 Output data set up (Q to StD) tQStD 3.4 s TOE=VDD Propagation delay (TOE to Q ENABLE) tPTE 50 ns load of 10 k, 50 pF Propagation delay (TOE to Q DISABLE) tPTD 300 ns load of 10 k, 50 pF P D W N Power-up time tPU 30 ms Note 3 Power-down time tPD 20 ms Crystal/clock frequency fC 3.5759 3.5795 3.5831 MHz 14 15 40 Conditions C L O C K Clock input rise time tLHCL 110 ns Ext. clock Clock input fall time tHLCL 110 ns Ext. clock Clock input duty cycle DCCL 60 % Ext. clock 40 50 18 Capacitive load (OSC2) CLO 30 Typical figures are at 25C and are for design aid only: not guaranteed and not subject to production testing. pF *NOTES: 1. Used for guard-time calculation purposes only. 2. These, user adjustable parameters, are not device specifications. The adjustable settings of these minimums and maximums are recommendations based upon network requirements. 3. With valid tone present at input, t PU equals time from PDWN going low until ESt going high. VDD C1 DTMF Input R1 R2 C2 MT8870D/MT8870D-1 IN+ VDD IN- St/GT ESt StD Q4 Q3 Q2 Q1 TOE GS VRef INH PDWN OSC 1 X-tal OSC 2 VSS R3 NOTES: R1,R2=100K 1% R3=300K 1% C1,C2=100 nF 5% X-tal=3.579545 MHz 0.1% Figure 10 - Single-Ended Input Configuration 4-20 ISO2-CMOS MT8870D/MT8870D-1 D A EVENTS B C tREC tREC E TONE #n + 1 tDP G tDO tID TONE #n Vin F TONE #n + 1 tDA ESt tGTA tGTP VTSt St/GT tPQ tQStD Q1-Q4 DECODED TONE # (n-1) HIGH IMPEDANCE #n # (n + 1) tPSrD StD tPTE tPTD TOE EXPLANATION OF EVENTS A) TONE BURSTS DETECTED, TONE DURATION INVALID, OUTPUTS NOT UPDATED. B) TONE #n DETECTED, TONE DURATION VALID, TONE DECODED AND LATCHED IN OUTPUTS C) END OF TONE #n DETECTED, TONE ABSENT DURATION VALID, OUTPUTS REMIAN LATCHED UNTIL NEXT VALID TONE. D) OUTPUTS SWITCHED TO HIGH IMPEDANCE STATE. E) TONE #n + 1 DETECTED, TONE DURATION VALID, TONE DECODED AND LATCHED IN OUTPUTS (CURRENTLY HIGH IMPEDANCE). F) ACCEPTABLE DROPOUT OF TONE #n + 1, TONE ABSENT DURATION INVALID, OUTPUTS REMAIN LATCHED. G) END OF TONE #n + 1 DETECTED, TONE ABSENT DURATION VALID, OUTPUTS REMAIN LATCHED UNTIL NEXT VALID TONE. EXPLANATION OF SYMBOLS Vin DTMF COMPOSITE INPUT SIGNAL. ESt EARLY STEERING OUTPUT. INDICATES DETECTION OF VALID TONE FREQUENCIES. St/GT STEERING INPUT/GUARD TIME OUTPUT. DRIVES EXTERNAL RC TIMING CIRCUIT. 4-BIT DECODED TONE OUTPUT. Q1-Q4 StD DELAYED STEERING OUTPUT. INDICATES THAT VALID FREQUENCIES HAVE BEEN PRESENT/ABSENT FOR THE REQUIRED GUARD TIME THUS CONSTITUTING A VALID SIGNAL. TOE TONE OUTPUT ENABLE (INPUT). A LOW LEVEL SHIFTS Q1-Q4 TO ITS HIGH IMPEDANCE STATE. tREC MAXIMUM DTMF SIGNAL DURATION NOT DETECED AS VALID tREC MINIMUM DTMF SIGNAL DURATION REQUIRED FOR VALID RECOGNITION tID MAXIMUM TIME BETWEEN VALID DTMF SIGNALS. tDO MAXIMUM ALLOWABLE DROP OUT DURING VALID DTMF SIGNAL. tDP TIME TO DETECT THE PRESENCE OF VALID DTMF SIGNALS. tDA TIME TO DETECT THE ABSENCE OF VALID DTMF SIGNALS. tGTP GUARD TIME, TONE PRESENT. tGTA GUARD TIME, TONE ABSENT. Figure 11 - Timing Diagram 4-21 MT8870D/MT8870D-1 Notes: 4-22 ISO2-CMOS Package Outlines 3 2 1 E1 E n-2 n-1 n D A2 A L C eA b2 e eC eB b Notes: D1 1) Not to scale 2) Dimensions in inches 3) (Dimensions in millimeters) Plastic Dual-In-Line Packages (PDIP) - E Suffix DIM 8-Pin 16-Pin 18-Pin 20-Pin Plastic Plastic Plastic Plastic Min A Max Min 0.210 (5.33) Max Min 0.210 (5.33) Max Min 0.210 (5.33) Max 0.210 (5.33) A2 0.115 (2.92) 0.195 (4.95) 0.115 (2.92) 0.195 (4.95) 0.115 (2.92) 0.195 (4.95) 0.115 (2.92) 0.195 (4.95) b 0.014 (0.356) 0.022 (0.558) 0.014 (0.356) 0.022 (0.558) 0.014 (0.356) 0.022 (0.558) 0.014 (0.356) 0.022 (0.558) b2 0.045 (1.14) 0.070 (1.77) 0.045 (1.14) 0.070 (1.77) 0.045 (1.14) 0.070 (1.77) 0.045 (1.14) 0.070 (1.77) C 0.008 (0.203) 0.014 (0.356) 0.008 (0.203) 0.014(0.356) 0.008 (0.203) 0.014 (0.356) 0.008 (0.203) 0.014 (0.356) D 0.355 (9.02) 0.400 (10.16) 0.780 (19.81) 0.800 (20.32) 0.880 (22.35) 0.920 (23.37) 0.980 (24.89) 1.060 (26.9) D1 0.005 (0.13) E 0.300 (7.62) 0.325 (8.26) 0.300 (7.62) 0.325 (8.26) 0.300 (7.62) 0.325 (8.26) 0.300 (7.62) 0.325 (8.26) E1 0.240 (6.10) 0.280 (7.11) 0.240 (6.10) 0.280 (7.11) 0.240 (6.10) 0.280 (7.11) 0.240 (6.10) 0.280 (7.11) 0.005 (0.13) 0.005 (0.13) 0.005 (0.13) e 0.100 BSC (2.54) 0.100 BSC (2.54) 0.100 BSC (2.54) 0.100 BSC (2.54) eA 0.300 BSC (7.62) 0.300 BSC (7.62) 0.300 BSC (7.62) 0.300 BSC (7.62) L 0.115 (2.92) eB eC 0.150 (3.81) 0.115 (2.92) 0.430 (10.92) 0 0.060 (1.52) 0.150 (3.81) 0.430 (10.92) 0 0.060 (1.52) NOTE: Controlling dimensions in parenthesis ( ) are in millimeters. General-8 0.115 (2.92) 0.150 (3.81) 0.115 (2.92) 0.430 (10.92) 0 0.060 (1.52) 0.150 (3.81) 0.430 (10.92) 0 0.060 (1.52) Package Outlines 3 2 1 E1 E n-2 n-1 n D A2 A L C eA b2 e eB b Notes: D1 1) Not to scale 2) Dimensions in inches 3) (Dimensions in millimeters) Plastic Dual-In-Line Packages (PDIP) - E Suffix DIM 22-Pin 24-Pin 28-Pin 40-Pin Plastic Plastic Plastic Plastic Min A Max Min 0.210 (5.33) Max Min 0.250 (6.35) Max Min 0.250 (6.35) Max 0.250 (6.35) A2 0.125 (3.18) 0.195 (4.95) 0.125 (3.18) 0.195 (4.95) 0.125 (3.18) 0.195 (4.95) 0.125 (3.18) 0.195 (4.95) b 0.014 (0.356) 0.022 (0.558) 0.014 (0.356) 0.022 (0.558) 0.014 (0.356) 0.022 (0.558) 0.014 (0.356) 0.022 (0.558) b2 0.045 (1.15) 0.070 (1.77) 0.030 (0.77) 0.070 (1.77) 0.030 (0.77) 0.070 (1.77) 0.030 (0.77) 0.070 (1.77) C 0.008 (0.204) 0.015 (0.381) 0.008 (0.204) 0.015 (0.381) 0.008 (0.204) 0.015 (0.381) 0.008 (0.204) 0.015 (0.381) D 1.050 (26.67) 1.120 (28.44) 1.150 (29.3) 1.290 (32.7) 1.380 (35.1) 1.565 (39.7) 1.980 (50.3) 2.095 (53.2) D1 0.005 (0.13) E 0.390 (9.91) 0.005 (0.13) 0.430 (10.92) E E1 0.330 (8.39) 0.380 (9.65) E1 0.005 (0.13) 0.600 (15.24) 0.670 (17.02) 0.290 (7.37) .330 (8.38) 0.485 (12.32) 0.580 (14.73) 0.246 (6.25) 0.254 (6.45) 0.005 (0.13) 0.600 (15.24) 0.670 (17.02) 0.600 (15.24) 0.670 (17.02) 0.485 (12.32) 0.580 (14.73) 0.485 (12.32) 0.580 (14.73) e 0.100 BSC (2.54) 0.100 BSC (2.54) 0.100 BSC (2.54) 0.100 BSC (2.54) eA 0.400 BSC (10.16) 0.600 BSC (15.24) 0.600 BSC (15.24) 0.600 BSC (15.24) eA 0.300 BSC (7.62) eB L 0.430 (10.92) 0.115 (2.93) 0.160 (4.06) 0.115 (2.93) 0.200 (5.08) 15 Shaded areas for 300 Mil Body Width 24 PDIP only 15 0.115 (2.93) 0.200 (5.08) 15 0.115 (2.93) 0.200 (5.08) 15 Package Outlines Pin 1 E A C L H e D L 4 mils (lead coplanarity) Notes: 1) Not to scale 2) Dimensions in inches 3) (Dimensions in millimeters) 4) A & B Maximum dimensions include allowable mold flash A1 B DIM 16-Pin 18-Pin 20-Pin 24-Pin 28-Pin Min Max Min Max Min Max Min Max Min Max A 0.093 (2.35) 0.104 (2.65) 0.093 (2.35) 0.104 (2.65) 0.093 (2.35) 0.104 (2.65) 0.093 (2.35) 0.104 (2.65) 0.093 (2.35) 0.104 (2.65) A1 0.004 (0.10) 0.012 (0.30) 0.004 (0.10) 0.012 (0.30) 0.004 (0.10) 0.012 (0.30) 0.004 (0.10) 0.012 (0.30) 0.004 (0.10) 0.012 (0.30) B 0.013 (0.33) 0.020 (0.51) 0.013 (0.33) 0.030 (0.51) 0.013 (0.33) 0.020 (0.51) 0.013 (0.33) 0.020 (0.51) 0.013 (0.33) 0.020 (0.51) C 0.009 (0.231) 0.013 (0.318) 0.009 (0.231) 0.013 (0.318) 0.009 (0.231) 0.013 (0.318) 0.009 (0.231) 0.013 (0.318) 0.009 (0.231) 0.013 (0.318) D 0.398 (10.1) 0.413 (10.5) 0.447 (11.35) 0.4625 (11.75) 0.496 (12.60) 0.512 (13.00) 0.5985 (15.2) 0.614 (15.6) 0.697 (17.7) 0.7125 (18.1) E 0.291 (7.40) 0.299 (7.40) 0.291 (7.40) 0.299 (7.40) 0.291 (7.40) 0.299 (7.40) 0.291 (7.40) 0.299 (7.40) 0.291 (7.40) 0.299 (7.40) e 0.050 BSC (1.27 BSC) 0.050 BSC (1.27 BSC) 0.050 BSC (1.27 BSC) 0.050 BSC (1.27 BSC) 0.050 BSC (1.27 BSC) H 0.394 (10.00) 0.419 (10.65) 0.394 (10.00) 0.419 (10.65) 0.394 (10.00) 0.419 (10.65) 0.394 (10.00) 0.419 (10.65) 0.394 (10.00) 0.419 (10.65) L 0.016 (0.40) 0.050 (1.27) 0.016 (0.40) 0.050 (1.27) 0.016 (0.40) 0.050 (1.27) 0.016 (0.40) 0.050 (1.27) 0.016 (0.40) 0.050 (1.27) Lead SOIC Package - S Suffix NOTES: 1. Controlling dimensions in parenthesis ( ) are in millimeters. 2. Converted inch dimensions are not necessarily exact. General-7 Package Outlines Pin 1 E A C L H e Notes: 1) Not to scale 2) Dimensions in inches 3) (Dimensions in millimeters) 4) Ref. JEDEC Standard M0-150/M0118 for 48 Pin 5) A & B Maximum dimensions include allowable mold flash D A2 A1 B 20-Pin 24-Pin 28-Pin 48-Pin Dim Min A A1 0.002 (0.05) B 0.0087 (0.22) C Max Min Max 0.079 (2) - 0.079 (2) 0.002 (0.05) 0.013 (0.33) 0.0087 (0.22) 0.008 (0.21) Min Max Min Max 0.079 (2) 0.095 (2.41) 0.110 (2.79) 0.008 (0.2) 0.016 (0.406) 0.008 (0.2) 0.0135 (0.342) 0.002 (0.05) 0.013 (0.33) 0.0087 (0.22) 0.008 (0.21) 0.013 (0.33) 0.008 (0.21) 0.010 (0.25) D 0.27 (6.9) 0.295 (7.5) 0.31 (7.9) 0.33 (8.5) 0.39 (9.9) 0.42 (10.5) 0.62 (15.75) 0.63 (16.00) E 0.2 (5.0) 0.22 (5.6) 0.2 (5.0) 0.22 (5.6) 0.2 (5.0) 0.22 (5.6) 0.291 (7.39) 0.299 (7.59) e 0.025 BSC (0.635 BSC) 0.025 BSC (0.635 BSC) 0.025 BSC (0.635 BSC) 0.025 BSC (0.635 BSC) A2 0.065 (1.65) 0.073 (1.85) 0.065 (1.65) 0.073 (1.85) 0.065 (1.65) 0.073 (1.85) 0.089 (2.26) 0.099 (2.52) H 0.29 (7.4) 0.32 (8.2) 0.29 (7.4) 0.32 (8.2) 0.29 (7.4) 0.32 (8.2) 0.395 (10.03) 0.42 (10.67) L 0.022 (0.55) 0.037 (0.95) 0.022 (0.55) 0.037 (0.95) 0.022 (0.55) 0.037 (0.95) 0.02 (0.51) 0.04 (1.02) Small Shrink Outline Package (SSOP) - N Suffix General-11 Package Outlines 3 2 1 E1 E n-2 n-1 n D A2 A L C eA b2 e eC eB b Notes: D1 1) Not to scale 2) Dimensions in inches 3) (Dimensions in millimeters) Plastic Dual-In-Line Packages (PDIP) - E Suffix DIM 8-Pin 16-Pin 18-Pin 20-Pin Plastic Plastic Plastic Plastic Min A Max Min 0.210 (5.33) Max Min 0.210 (5.33) Max Min 0.210 (5.33) Max 0.210 (5.33) A2 0.115 (2.92) 0.195 (4.95) 0.115 (2.92) 0.195 (4.95) 0.115 (2.92) 0.195 (4.95) 0.115 (2.92) 0.195 (4.95) b 0.014 (0.356) 0.022 (0.558) 0.014 (0.356) 0.022 (0.558) 0.014 (0.356) 0.022 (0.558) 0.014 (0.356) 0.022 (0.558) b2 0.045 (1.14) 0.070 (1.77) 0.045 (1.14) 0.070 (1.77) 0.045 (1.14) 0.070 (1.77) 0.045 (1.14) 0.070 (1.77) C 0.008 (0.203) 0.014 (0.356) 0.008 (0.203) 0.014(0.356) 0.008 (0.203) 0.014 (0.356) 0.008 (0.203) 0.014 (0.356) D 0.355 (9.02) 0.400 (10.16) 0.780 (19.81) 0.800 (20.32) 0.880 (22.35) 0.920 (23.37) 0.980 (24.89) 1.060 (26.9) D1 0.005 (0.13) E 0.300 (7.62) 0.325 (8.26) 0.300 (7.62) 0.325 (8.26) 0.300 (7.62) 0.325 (8.26) 0.300 (7.62) 0.325 (8.26) E1 0.240 (6.10) 0.280 (7.11) 0.240 (6.10) 0.280 (7.11) 0.240 (6.10) 0.280 (7.11) 0.240 (6.10) 0.280 (7.11) 0.005 (0.13) 0.005 (0.13) 0.005 (0.13) e 0.100 BSC (2.54) 0.100 BSC (2.54) 0.100 BSC (2.54) 0.100 BSC (2.54) eA 0.300 BSC (7.62) 0.300 BSC (7.62) 0.300 BSC (7.62) 0.300 BSC (7.62) L 0.115 (2.92) eB eC 0.150 (3.81) 0.115 (2.92) 0.430 (10.92) 0 0.060 (1.52) 0.150 (3.81) 0.430 (10.92) 0 0.060 (1.52) NOTE: Controlling dimensions in parenthesis ( ) are in millimeters. General-8 0.115 (2.92) 0.150 (3.81) 0.115 (2.92) 0.430 (10.92) 0 0.060 (1.52) 0.150 (3.81) 0.430 (10.92) 0 0.060 (1.52) Package Outlines 3 2 1 E1 E n-2 n-1 n D A2 A L C eA b2 e eB b Notes: D1 1) Not to scale 2) Dimensions in inches 3) (Dimensions in millimeters) Plastic Dual-In-Line Packages (PDIP) - E Suffix DIM 22-Pin 24-Pin 28-Pin 40-Pin Plastic Plastic Plastic Plastic Min A Max Min 0.210 (5.33) Max Min 0.250 (6.35) Max Min 0.250 (6.35) Max 0.250 (6.35) A2 0.125 (3.18) 0.195 (4.95) 0.125 (3.18) 0.195 (4.95) 0.125 (3.18) 0.195 (4.95) 0.125 (3.18) 0.195 (4.95) b 0.014 (0.356) 0.022 (0.558) 0.014 (0.356) 0.022 (0.558) 0.014 (0.356) 0.022 (0.558) 0.014 (0.356) 0.022 (0.558) b2 0.045 (1.15) 0.070 (1.77) 0.030 (0.77) 0.070 (1.77) 0.030 (0.77) 0.070 (1.77) 0.030 (0.77) 0.070 (1.77) C 0.008 (0.204) 0.015 (0.381) 0.008 (0.204) 0.015 (0.381) 0.008 (0.204) 0.015 (0.381) 0.008 (0.204) 0.015 (0.381) D 1.050 (26.67) 1.120 (28.44) 1.150 (29.3) 1.290 (32.7) 1.380 (35.1) 1.565 (39.7) 1.980 (50.3) 2.095 (53.2) D1 0.005 (0.13) E 0.390 (9.91) 0.005 (0.13) 0.430 (10.92) E E1 0.330 (8.39) 0.380 (9.65) E1 0.005 (0.13) 0.600 (15.24) 0.670 (17.02) 0.290 (7.37) .330 (8.38) 0.485 (12.32) 0.580 (14.73) 0.246 (6.25) 0.254 (6.45) 0.005 (0.13) 0.600 (15.24) 0.670 (17.02) 0.600 (15.24) 0.670 (17.02) 0.485 (12.32) 0.580 (14.73) 0.485 (12.32) 0.580 (14.73) e 0.100 BSC (2.54) 0.100 BSC (2.54) 0.100 BSC (2.54) 0.100 BSC (2.54) eA 0.400 BSC (10.16) 0.600 BSC (15.24) 0.600 BSC (15.24) 0.600 BSC (15.24) eA 0.300 BSC (7.62) eB L 0.430 (10.92) 0.115 (2.93) 0.160 (4.06) 0.115 (2.93) 0.200 (5.08) 15 Shaded areas for 300 Mil Body Width 24 PDIP only 15 0.115 (2.93) 0.200 (5.08) 15 0.115 (2.93) 0.200 (5.08) 15 Package Outlines Pin 1 E A C L H e D L 4 mils (lead coplanarity) Notes: 1) Not to scale 2) Dimensions in inches 3) (Dimensions in millimeters) 4) A & B Maximum dimensions include allowable mold flash A1 B DIM 16-Pin 18-Pin 20-Pin 24-Pin 28-Pin Min Max Min Max Min Max Min Max Min Max A 0.093 (2.35) 0.104 (2.65) 0.093 (2.35) 0.104 (2.65) 0.093 (2.35) 0.104 (2.65) 0.093 (2.35) 0.104 (2.65) 0.093 (2.35) 0.104 (2.65) A1 0.004 (0.10) 0.012 (0.30) 0.004 (0.10) 0.012 (0.30) 0.004 (0.10) 0.012 (0.30) 0.004 (0.10) 0.012 (0.30) 0.004 (0.10) 0.012 (0.30) B 0.013 (0.33) 0.020 (0.51) 0.013 (0.33) 0.030 (0.51) 0.013 (0.33) 0.020 (0.51) 0.013 (0.33) 0.020 (0.51) 0.013 (0.33) 0.020 (0.51) C 0.009 (0.231) 0.013 (0.318) 0.009 (0.231) 0.013 (0.318) 0.009 (0.231) 0.013 (0.318) 0.009 (0.231) 0.013 (0.318) 0.009 (0.231) 0.013 (0.318) D 0.398 (10.1) 0.413 (10.5) 0.447 (11.35) 0.4625 (11.75) 0.496 (12.60) 0.512 (13.00) 0.5985 (15.2) 0.614 (15.6) 0.697 (17.7) 0.7125 (18.1) E 0.291 (7.40) 0.299 (7.40) 0.291 (7.40) 0.299 (7.40) 0.291 (7.40) 0.299 (7.40) 0.291 (7.40) 0.299 (7.40) 0.291 (7.40) 0.299 (7.40) e 0.050 BSC (1.27 BSC) 0.050 BSC (1.27 BSC) 0.050 BSC (1.27 BSC) 0.050 BSC (1.27 BSC) 0.050 BSC (1.27 BSC) H 0.394 (10.00) 0.419 (10.65) 0.394 (10.00) 0.419 (10.65) 0.394 (10.00) 0.419 (10.65) 0.394 (10.00) 0.419 (10.65) 0.394 (10.00) 0.419 (10.65) L 0.016 (0.40) 0.050 (1.27) 0.016 (0.40) 0.050 (1.27) 0.016 (0.40) 0.050 (1.27) 0.016 (0.40) 0.050 (1.27) 0.016 (0.40) 0.050 (1.27) Lead SOIC Package - S Suffix NOTES: 1. Controlling dimensions in parenthesis ( ) are in millimeters. 2. Converted inch dimensions are not necessarily exact. General-7 Package Outlines Pin 1 E A C L H e Notes: 1) Not to scale 2) Dimensions in inches 3) (Dimensions in millimeters) 4) Ref. JEDEC Standard M0-150/M0118 for 48 Pin 5) A & B Maximum dimensions include allowable mold flash D A2 A1 B 20-Pin 24-Pin 28-Pin 48-Pin Dim Min A A1 0.002 (0.05) B 0.0087 (0.22) C Max Min Max 0.079 (2) - 0.079 (2) 0.002 (0.05) 0.013 (0.33) 0.0087 (0.22) 0.008 (0.21) Min Max Min Max 0.079 (2) 0.095 (2.41) 0.110 (2.79) 0.008 (0.2) 0.016 (0.406) 0.008 (0.2) 0.0135 (0.342) 0.002 (0.05) 0.013 (0.33) 0.0087 (0.22) 0.008 (0.21) 0.013 (0.33) 0.008 (0.21) 0.010 (0.25) D 0.27 (6.9) 0.295 (7.5) 0.31 (7.9) 0.33 (8.5) 0.39 (9.9) 0.42 (10.5) 0.62 (15.75) 0.63 (16.00) E 0.2 (5.0) 0.22 (5.6) 0.2 (5.0) 0.22 (5.6) 0.2 (5.0) 0.22 (5.6) 0.291 (7.39) 0.299 (7.59) e 0.025 BSC (0.635 BSC) 0.025 BSC (0.635 BSC) 0.025 BSC (0.635 BSC) 0.025 BSC (0.635 BSC) A2 0.065 (1.65) 0.073 (1.85) 0.065 (1.65) 0.073 (1.85) 0.065 (1.65) 0.073 (1.85) 0.089 (2.26) 0.099 (2.52) H 0.29 (7.4) 0.32 (8.2) 0.29 (7.4) 0.32 (8.2) 0.29 (7.4) 0.32 (8.2) 0.395 (10.03) 0.42 (10.67) L 0.022 (0.55) 0.037 (0.95) 0.022 (0.55) 0.037 (0.95) 0.022 (0.55) 0.037 (0.95) 0.02 (0.51) 0.04 (1.02) Small Shrink Outline Package (SSOP) - N Suffix General-11 Package Outlines 3 2 1 E1 E n-2 n-1 n D A2 A L C eA b2 e eC eB b Notes: D1 1) Not to scale 2) Dimensions in inches 3) (Dimensions in millimeters) Plastic Dual-In-Line Packages (PDIP) - E Suffix DIM 8-Pin 16-Pin 18-Pin 20-Pin Plastic Plastic Plastic Plastic Min A Max Min 0.210 (5.33) Max Min 0.210 (5.33) Max Min 0.210 (5.33) Max 0.210 (5.33) A2 0.115 (2.92) 0.195 (4.95) 0.115 (2.92) 0.195 (4.95) 0.115 (2.92) 0.195 (4.95) 0.115 (2.92) 0.195 (4.95) b 0.014 (0.356) 0.022 (0.558) 0.014 (0.356) 0.022 (0.558) 0.014 (0.356) 0.022 (0.558) 0.014 (0.356) 0.022 (0.558) b2 0.045 (1.14) 0.070 (1.77) 0.045 (1.14) 0.070 (1.77) 0.045 (1.14) 0.070 (1.77) 0.045 (1.14) 0.070 (1.77) C 0.008 (0.203) 0.014 (0.356) 0.008 (0.203) 0.014(0.356) 0.008 (0.203) 0.014 (0.356) 0.008 (0.203) 0.014 (0.356) D 0.355 (9.02) 0.400 (10.16) 0.780 (19.81) 0.800 (20.32) 0.880 (22.35) 0.920 (23.37) 0.980 (24.89) 1.060 (26.9) D1 0.005 (0.13) E 0.300 (7.62) 0.325 (8.26) 0.300 (7.62) 0.325 (8.26) 0.300 (7.62) 0.325 (8.26) 0.300 (7.62) 0.325 (8.26) E1 0.240 (6.10) 0.280 (7.11) 0.240 (6.10) 0.280 (7.11) 0.240 (6.10) 0.280 (7.11) 0.240 (6.10) 0.280 (7.11) 0.005 (0.13) 0.005 (0.13) 0.005 (0.13) e 0.100 BSC (2.54) 0.100 BSC (2.54) 0.100 BSC (2.54) 0.100 BSC (2.54) eA 0.300 BSC (7.62) 0.300 BSC (7.62) 0.300 BSC (7.62) 0.300 BSC (7.62) L 0.115 (2.92) eB eC 0.150 (3.81) 0.115 (2.92) 0.430 (10.92) 0 0.060 (1.52) 0.150 (3.81) 0.430 (10.92) 0 0.060 (1.52) NOTE: Controlling dimensions in parenthesis ( ) are in millimeters. General-8 0.115 (2.92) 0.150 (3.81) 0.115 (2.92) 0.430 (10.92) 0 0.060 (1.52) 0.150 (3.81) 0.430 (10.92) 0 0.060 (1.52) Package Outlines 3 2 1 E1 E n-2 n-1 n D A2 A L C eA b2 e eB b Notes: D1 1) Not to scale 2) Dimensions in inches 3) (Dimensions in millimeters) Plastic Dual-In-Line Packages (PDIP) - E Suffix DIM 22-Pin 24-Pin 28-Pin 40-Pin Plastic Plastic Plastic Plastic Min A Max Min 0.210 (5.33) Max Min 0.250 (6.35) Max Min 0.250 (6.35) Max 0.250 (6.35) A2 0.125 (3.18) 0.195 (4.95) 0.125 (3.18) 0.195 (4.95) 0.125 (3.18) 0.195 (4.95) 0.125 (3.18) 0.195 (4.95) b 0.014 (0.356) 0.022 (0.558) 0.014 (0.356) 0.022 (0.558) 0.014 (0.356) 0.022 (0.558) 0.014 (0.356) 0.022 (0.558) b2 0.045 (1.15) 0.070 (1.77) 0.030 (0.77) 0.070 (1.77) 0.030 (0.77) 0.070 (1.77) 0.030 (0.77) 0.070 (1.77) C 0.008 (0.204) 0.015 (0.381) 0.008 (0.204) 0.015 (0.381) 0.008 (0.204) 0.015 (0.381) 0.008 (0.204) 0.015 (0.381) D 1.050 (26.67) 1.120 (28.44) 1.150 (29.3) 1.290 (32.7) 1.380 (35.1) 1.565 (39.7) 1.980 (50.3) 2.095 (53.2) D1 0.005 (0.13) E 0.390 (9.91) 0.005 (0.13) 0.430 (10.92) E E1 0.330 (8.39) 0.380 (9.65) E1 0.005 (0.13) 0.600 (15.24) 0.670 (17.02) 0.290 (7.37) .330 (8.38) 0.485 (12.32) 0.580 (14.73) 0.246 (6.25) 0.254 (6.45) 0.005 (0.13) 0.600 (15.24) 0.670 (17.02) 0.600 (15.24) 0.670 (17.02) 0.485 (12.32) 0.580 (14.73) 0.485 (12.32) 0.580 (14.73) e 0.100 BSC (2.54) 0.100 BSC (2.54) 0.100 BSC (2.54) 0.100 BSC (2.54) eA 0.400 BSC (10.16) 0.600 BSC (15.24) 0.600 BSC (15.24) 0.600 BSC (15.24) eA 0.300 BSC (7.62) eB L 0.430 (10.92) 0.115 (2.93) 0.160 (4.06) 0.115 (2.93) 0.200 (5.08) 15 Shaded areas for 300 Mil Body Width 24 PDIP only 15 0.115 (2.93) 0.200 (5.08) 15 0.115 (2.93) 0.200 (5.08) 15 Package Outlines Pin 1 E A C L H e D L 4 mils (lead coplanarity) Notes: 1) Not to scale 2) Dimensions in inches 3) (Dimensions in millimeters) 4) A & B Maximum dimensions include allowable mold flash A1 B DIM 16-Pin 18-Pin 20-Pin 24-Pin 28-Pin Min Max Min Max Min Max Min Max Min Max A 0.093 (2.35) 0.104 (2.65) 0.093 (2.35) 0.104 (2.65) 0.093 (2.35) 0.104 (2.65) 0.093 (2.35) 0.104 (2.65) 0.093 (2.35) 0.104 (2.65) A1 0.004 (0.10) 0.012 (0.30) 0.004 (0.10) 0.012 (0.30) 0.004 (0.10) 0.012 (0.30) 0.004 (0.10) 0.012 (0.30) 0.004 (0.10) 0.012 (0.30) B 0.013 (0.33) 0.020 (0.51) 0.013 (0.33) 0.030 (0.51) 0.013 (0.33) 0.020 (0.51) 0.013 (0.33) 0.020 (0.51) 0.013 (0.33) 0.020 (0.51) C 0.009 (0.231) 0.013 (0.318) 0.009 (0.231) 0.013 (0.318) 0.009 (0.231) 0.013 (0.318) 0.009 (0.231) 0.013 (0.318) 0.009 (0.231) 0.013 (0.318) D 0.398 (10.1) 0.413 (10.5) 0.447 (11.35) 0.4625 (11.75) 0.496 (12.60) 0.512 (13.00) 0.5985 (15.2) 0.614 (15.6) 0.697 (17.7) 0.7125 (18.1) E 0.291 (7.40) 0.299 (7.40) 0.291 (7.40) 0.299 (7.40) 0.291 (7.40) 0.299 (7.40) 0.291 (7.40) 0.299 (7.40) 0.291 (7.40) 0.299 (7.40) e 0.050 BSC (1.27 BSC) 0.050 BSC (1.27 BSC) 0.050 BSC (1.27 BSC) 0.050 BSC (1.27 BSC) 0.050 BSC (1.27 BSC) H 0.394 (10.00) 0.419 (10.65) 0.394 (10.00) 0.419 (10.65) 0.394 (10.00) 0.419 (10.65) 0.394 (10.00) 0.419 (10.65) 0.394 (10.00) 0.419 (10.65) L 0.016 (0.40) 0.050 (1.27) 0.016 (0.40) 0.050 (1.27) 0.016 (0.40) 0.050 (1.27) 0.016 (0.40) 0.050 (1.27) 0.016 (0.40) 0.050 (1.27) Lead SOIC Package - S Suffix NOTES: 1. Controlling dimensions in parenthesis ( ) are in millimeters. 2. Converted inch dimensions are not necessarily exact. General-7 Package Outlines Pin 1 E A C L H e Notes: 1) Not to scale 2) Dimensions in inches 3) (Dimensions in millimeters) 4) Ref. JEDEC Standard M0-150/M0118 for 48 Pin 5) A & B Maximum dimensions include allowable mold flash D A2 A1 B 20-Pin 24-Pin 28-Pin 48-Pin Dim Min A A1 0.002 (0.05) B 0.0087 (0.22) C Max Min Max 0.079 (2) - 0.079 (2) 0.002 (0.05) 0.013 (0.33) 0.0087 (0.22) 0.008 (0.21) Min Max Min Max 0.079 (2) 0.095 (2.41) 0.110 (2.79) 0.008 (0.2) 0.016 (0.406) 0.008 (0.2) 0.0135 (0.342) 0.002 (0.05) 0.013 (0.33) 0.0087 (0.22) 0.008 (0.21) 0.013 (0.33) 0.008 (0.21) 0.010 (0.25) D 0.27 (6.9) 0.295 (7.5) 0.31 (7.9) 0.33 (8.5) 0.39 (9.9) 0.42 (10.5) 0.62 (15.75) 0.63 (16.00) E 0.2 (5.0) 0.22 (5.6) 0.2 (5.0) 0.22 (5.6) 0.2 (5.0) 0.22 (5.6) 0.291 (7.39) 0.299 (7.59) e 0.025 BSC (0.635 BSC) 0.025 BSC (0.635 BSC) 0.025 BSC (0.635 BSC) 0.025 BSC (0.635 BSC) A2 0.065 (1.65) 0.073 (1.85) 0.065 (1.65) 0.073 (1.85) 0.065 (1.65) 0.073 (1.85) 0.089 (2.26) 0.099 (2.52) H 0.29 (7.4) 0.32 (8.2) 0.29 (7.4) 0.32 (8.2) 0.29 (7.4) 0.32 (8.2) 0.395 (10.03) 0.42 (10.67) L 0.022 (0.55) 0.037 (0.95) 0.022 (0.55) 0.037 (0.95) 0.022 (0.55) 0.037 (0.95) 0.02 (0.51) 0.04 (1.02) Small Shrink Outline Package (SSOP) - N Suffix General-11 For more information about all Zarlink products visit our Web Site at www.zarlink.com Information relating to products and services furnished herein by Zarlink Semiconductor Inc. trading as Zarlink Semiconductor or its subsidiaries (collectively "Zarlink") is believed to be reliable. However, Zarlink assumes no liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such information, product or service or for any infringement of patents or other intellectual property rights owned by third parties which may result from such application or use. Neither the supply of such information or purchase of product or service conveys any license, either express or implied, under patents or other intellectual property rights owned by Zarlink or licensed from third parties by Zarlink, whatsoever. Purchasers of products are also hereby notified that the use of product in certain ways or in combination with Zarlink, or non-Zarlink furnished goods or services may infringe patents or other intellectual property rights owned by Zarlink. This publication is issued to provide information only and (unless agreed by Zarlink in writing) may not be used, applied or reproduced for any purpose nor form part of any order or contract nor to be regarded as a representation relating to the products or services concerned. The products, their specifications, services and other information appearing in this publication are subject to change by Zarlink without notice. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user's responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. Manufacturing does not necessarily include testing of all functions or parameters. These products are not suitable for use in any medical products whose failure to perform may result in significant injury or death to the user. All products and materials are sold and services provided subject to Zarlink's conditions of sale which are available on request. Purchase of Zarlink's I2C components conveys a licence under the Philips I2C Patent rights to use these components in and I2C System, provided that the system conforms to the I2C Standard Specification as defined by Philips. Zarlink, ZL and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc. Copyright Zarlink Semiconductor Inc. All Rights Reserved. TECHNICAL DOCUMENTATION - NOT FOR RESALE