LAN91C93I Non-PCI Single-Chip Full Duplex Ethernet Controller Datasheet Product Features Dynamic Memory Allocation Between Transmit and Receive Non-PCI Single-Chip Ethernet Controller Fully Supports Full Duplex Switched Ethernet Flat Memory Structure for Low CPU Overhead Supports Enhanced Transmit Queue Management 6K Bytes of On-Chip RAM Buffered Architecture, Insensitive to Bus Latencies (No Overruns/Underruns) Supports IEEE 802.3 (ANSI 8802-3) Ethernet Standards Supports Boot PROM for Diskless local bus Applications Automatic Detection of TX/RX Polarity Reversal Network Interface Simultasking Early Transmit and Early Receive Functions Integrated 10BASE-T Transceiver Functions: - Driver and Receiver - Link Integrity Test - Receive Polarity Detection and Correction Enhanced Early Transmit Function Receive Counter for Enhanced Early Receive Hardware Memory Management Unit Integrated AUI Interface Optional Configuration via Serial EEPROM Interface (Jumperless) 10 Mb/s Manchester Encoding/Decoding and Clock Recovery Supports single 5V or 3.3V VCC Design Supports Mixed Voltage External PHY Designs Automatic Retransmission, Bad Packet Rejection, and Transmit Padding Supports Industrial Temp -40C to 85C External and Internal Loopback Modes Low Power CMOS Design Four Direct Driven LEDs for Status/ Diagnostics 100 Pin QFP and TQFP (1.0mm body Thickness) Packages Software Drivers Direct Interface to local bus, with No Wait States LAN9000 Drivers for Major Network Operating Systems Utilizing local bus Interface 16 Bit Data and Control Paths Fast Access Time Software Drivers Utilize Full Capability of 32 Bit Microprocessor Pipelined Data Path Handles Block Word Transfers for any Alignment High Performance Chained ("Back-to-Back") Transmit and Receive SMSC DS - LAN91C93I Page 1 DATASHEET Rev. 09/30/2002 Non-PCI Single-Chip Full Duplex Ethernet Controller ORDERING INFORMATION Order Number(s): LAN91C93I-MC, LAN91C93I-ME 100 Pin QFP/TQFP Package Options (c) STANDARD MICROSYSTEMS CORPORATION (SMSC) 2002 80 Arkay Drive Hauppauge, NY 11788 (631) 435-6000 FAX (631) 273-3123 Standard Microsystems and SMSC are registered trademarks of Standard Microsystems Corporation. Product names and company names are the trademarks of their respective holders. Circuit diagrams utilizing SMSC products are included as a means of illustrating typical applications; consequently complete information sufficient for construction purposes is not necessarily given. Although the information has been checked and is believed to be accurate, no responsibility is assumed for inaccuracies. SMSC reserves the right to make changes to specifications and product descriptions at any time without notice. Contact your local SMSC sales office to obtain the latest specifications before placing your product order. The provision of this information does not convey to the purchaser of the semiconductor devices described any licenses under the patent rights of SMSC or others. All sales are expressly conditional on your agreement to the terms and conditions of the most recently dated version of SMSC's standard Terms of Sale Agreement dated before the date of your order (the "Terms of Sale Agreement"). The product may contain design defects or errors known as anomalies which may cause the product's functions to deviate from published specifications. Anomaly sheets are available upon request. SMSC products are not designed, intended, authorized or warranted for use in any life support or other application where product failure could cause or contribute to personal injury or severe property damage. Any and all such uses without prior written approval of an Officer of SMSC and further testing and/or modification will be fully at the risk of the customer. Copies of this document or other SMSC literature, as well as the Terms of Sale Agreement, may be obtained by visiting SMSC's website at http://www.smsc.com. SMSC DISCLAIMS AND EXCLUDES ANY AND ALL WARRANTIES, INCLUDING WITHOUT LIMITATION ANY AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE, AND AGAINST INFRINGEMENT AND THE LIKE, AND ANY AND ALL WARRANTIES ARISING FROM ANY COURSE OF DEALING OR USAGE OF TRADE. IN NO EVENT SHALL SMSC BE LIABLE FOR ANY DIRECT, INCIDENTAL, INDIRECT, SPECIAL, PUNITIVE, OR CONSEQUENTIAL DAMAGES, OR FOR LOST DATA, PROFITS, SAVINGS OR REVENUES OF ANY KIND; REGARDLESS OF THE FORM OF ACTION, WHETHER BASED ON CONTRACT, TORT, NEGLIGENCE OF SMSC OR OTHERS, STRICT LIABILITY, BREACH OF WARRANTY, OR OTHERWISE; WHETHER OR NOT ANY REMEDY IS HELD TO HAVE FAILED OF ITS ESSENTIAL PURPOSE; AND WHETHER OR NOT SMSC HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Rev. 09/30/2002 Page 2 DATASHEET SMSC DS - LAN91C93I Non-PCI Single-Chip Full Duplex Ethernet Controller TABLE OF CONTENTS Chapter 1 General Description ............................................................................................................. 6 Chapter 2 Overview ............................................................................................................................... 7 Chapter 3 Pin Configurations ............................................................................................................... 9 3.1 Local Bus Pin Requirements ............................................................................................................. 12 Chapter 4 4.1 Description of Pin Functions ............................................................................................. 13 Buffer Symbols .................................................................................................................................. 15 Chapter 5 5.1 5.2 5.3 5.4 Functional Description ....................................................................................................... 17 Buffer Memory ................................................................................................................................... 18 Interrupt Structure ............................................................................................................................. 24 Reset Logic........................................................................................................................................ 24 Power Down Logic States ................................................................................................................. 25 Chapter 6 Packet Format in Buffer Memory for Ethernet .............................................................. 26 Chapter 7 Registers Map in I/O Space............................................................................................... 29 7.1 7.2 I/O Space Access.............................................................................................................................. 29 I/O Space Registers Description ....................................................................................................... 30 7.2.1 Chapter 8 8.1 8.2 8.3 8.4 8.5 Bank Select Register ..............................................................................................................................30 Theory of Operation .......................................................................................................... 53 Full Duplex Support........................................................................................................................... 53 Typical Flow of Events for Transmit (Auto Release = 0)................................................................... 54 Typical Flow of Events for Transmit (Auto Release = 1)................................................................... 56 Typical Flow of Events for Receive ................................................................................................... 57 Memory Partitioning .......................................................................................................................... 63 Chapter 9 9.1 9.2 9.3 9.4 9.5 9.6 9.7 9.8 9.9 9.10 9.11 9.12 9.13 9.13.1 9.13.2 9.13.3 9.13.4 9.14 Functional Description of the Blocks................................................................................ 67 Memory Management Unit ................................................................................................................ 67 Arbiter ................................................................................................................................................ 67 Bus Interface ..................................................................................................................................... 68 Wait State Policy ............................................................................................................................... 68 Arbitration Considerations ................................................................................................................. 69 DMA Block......................................................................................................................................... 69 Packet Number FIFOs....................................................................................................................... 70 CSMA Bock ....................................................................................................................................... 72 Network Interface .............................................................................................................................. 74 10base-T ........................................................................................................................................ 74 AUI ................................................................................................................................................. 74 Physical Interface........................................................................................................................... 75 Transmit Functions......................................................................................................................... 75 Manchester Encoding .........................................................................................................................75 Transmit Drivers..................................................................................................................................75 Jabber Function ..................................................................................................................................75 SQE Function......................................................................................................................................75 Receive Functions.......................................................................................................................... 75 9.14.1 9.14.2 9.14.3 9.14.4 9.14.5 9.14.6 Receive Drivers...................................................................................................................................75 Manchester Decoder and Clock Recovery..........................................................................................76 Squelch Function ................................................................................................................................76 Reverse Polarity Function ...................................................................................................................76 Collision Detection Function................................................................................................................76 Link Integrity........................................................................................................................................76 SMSC DS - LAN91C93I Page 3 DATASHEET Rev. 09/30/2002 Non-PCI Single-Chip Full Duplex Ethernet Controller Chapter 10 10.1 10.2 Chapter 11 11.1 11.2 Board Setup Information ............................................................................................... 77 Diagnostic LEDs............................................................................................................................. 78 Bus Clock Considerations.............................................................................................................. 78 Operational Description ................................................................................................. 80 Maximum Guaranteed Ratings*..................................................................................................... 80 DC Electrical Characteristics ......................................................................................................... 80 Chapter 12 Timing Diagrams ............................................................................................................ 85 Chapter 13 LAN91C93I Revisions .................................................................................................. 102 LIST OF FIGURES Figure 3.1 - Pin Configuration of LAN91C93I QFP........................................................................................................9 Figure 3.2 - Pin Configuration of LAN91C93I TQFP....................................................................................................10 Figure 3.3 - System Diagram for Local Bus with Boot Prom .......................................................................................11 Figure 4.1 - LAN91C93I Internal Block Diagram ..........................................................................................................16 Figure 5.1 - Mapping and Paging vs. Receive and Transmit Area ..............................................................................19 Figure 5.2 - Transmit Queues and Mapping................................................................................................................20 Figure 5.3 - Receive Queues and Mapping.................................................................................................................21 Figure 5.4 - LAN91C93I Internal Block Diagram with Data Path .................................................................................22 Figure 5.5 - Logical Address Generation and Relevant Registers...............................................................................23 Figure 6.1 - Data Packet Format .................................................................................................................................26 Figure 7.1 - LAN91C93I Registers ...............................................................................................................................29 Figure 7.2 - Interrupt Structure ....................................................................................................................................49 Figure 8.1 - Interrupt Service Routine ..........................................................................................................................58 Figure 8.2 - RX INTR...................................................................................................................................................59 Figure 8.3 - TX INTR ...................................................................................................................................................60 Figure 8.4 - TXEMPTY INTR.......................................................................................................................................61 Figure 8.5 - Driver Send and Allocate Routines ..........................................................................................................62 Figure 8.6 - Interrupt Generation for Transmit; Receive, MMU ...................................................................................66 Figure 9.1 - MMU Packet Number Flow and Relevant Registers .................................................................................72 Figure 10.1 - 64 X 16 Serial EEPROM Map.................................................................................................................79 Figure 12.1 - Local Bus Consecutive Read Cycles.......................................................................................................85 Figure 12.2 - Local Bus Consecutive Write Cycles .......................................................................................................86 Figure 12.3 - Local Bus Consecutive Read and Write Cycles.......................................................................................87 Figure 12.4 - Data Register Special Read Access ......................................................................................................88 Figure 12.5 - Data Register Special Write Access.......................................................................................................89 Figure 12.6 - 8-Bit Mode Register Cycles ....................................................................................................................90 Figure 12.7 - EEPROM Read.......................................................................................................................................91 Figure 12.8 - External ROM Read Access ..................................................................................................................92 Figure 12.9 - EEPROM Write.......................................................................................................................................93 Figure 12.10 - Differential Output Signal Timing (10BASE-T and AUI) .......................................................................94 Figure 12.11 - Receive Timing - Start of Frame (AUI and 10BASE-T) .......................................................................95 Figure 12.12 - Receive Timing - End of Frame (AUI and 10BASE-T) ........................................................................96 Figure 12.13 - Transmit Timing - End of Frame (AUI and 10BASE-T)........................................................................97 Figure 12.14 - Collision and Timing (AUI) ...................................................................................................................98 Figure 12.15 - Memory Read Timing...........................................................................................................................98 Figure 12.16 - Input Clock Timing ...............................................................................................................................99 Figure 12.17 - Memory Write Timing...........................................................................................................................99 Figure 12.18 - 100 PIN QFP Package........................................................................................................................100 Figure 12.19 - 100 PIN TQFP Package.....................................................................................................................101 LIST OF TABLES Table 5.1 - LAN91C93I Address Space .......................................................................................................................24 Table 5.2 - Bus Transactions in Local Bus Mode .........................................................................................................24 Rev. 09/30/2002 Page 4 DATASHEET SMSC DS - LAN91C93I Non-PCI Single-Chip Full Duplex Ethernet Controller Table 5.3 - Interrupt Merging .......................................................................................................................................24 Table 5.4 - Reset Logic ...............................................................................................................................................25 Table 5.5 - Local Bus Mode Defined States (Refer To Table 5.6 For Next States To Wake-Up Events) .....................25 Table 5.6 - Local Bus Mode ........................................................................................................................................25 Table 7.1- Transmit Loop .............................................................................................................................................32 SMSC DS - LAN91C93I Page 5 DATASHEET Rev. 09/30/2002 Non-PCI Single-Chip Full Duplex Ethernet Controller Chapter 1 General Description The LAN91C93I is a VLSI, local bus interface Ethernet Controller. LAN91C93I integrates all MAC and physical layer functions, as well as the packet RAM, needed to implement a high performance 10BASE-T (twisted pair) node. For 10BASE5 (thick coax), 10BASE2 (thin coax), and 10BASE-F (fiber) implementations, the LAN91C93I interfaces to external transceivers via the provided AUI port. Only one additional IC is required for most applications. The LAN91C93I comes with Full Duplex Switched Ethernet (FDSWE) support allowing the controller to provide much higher throughput. 6K bytes of RAM is provided to support enhanced throughput and compensate for any increased system service latencies. The controller implements multiple advanced powerdown modes to conserve power and operate more efficiently. The LAN91C93I can directly interface with the local bus and deliver no-wait-state operation. For local bus interfaces, the LAN91C93I occupies 16 I/0 locations and no memory space. The same I/O space is used for local bus operations. Its shared memory is sequentially accessed with 40ns access times to any of its registers, including its packet memory. DMA services are not used by the LAN91C93I, virtually decoupling network traffic from local or system bus utilization. For packet memory management, the LAN91C93I integrates a unique hardware Memory Management Unit (MMU) with enhanced performance and decreased software overhead when compared to ring buffer and linked list architectures. The LAN91C93I is portable to different CPU and bus platforms due to its flexible bus interface, flat memory structure (no pointers), and its loosely coupled buffered architecture (not sensitive to latency). The LAN91C93I is available in 100-pin QFP and TQFP (1.0 mm body thickness) packages. The low profile TQFP is ideal for mobile applications such as PC Card LAN adapters. The LAN91C93I operates with a single power supply voltage of 5V or 3.3V. Rev. 09/30/2002 Page 6 DATASHEET SMSC DS - LAN91C93I Non-PCI Single-Chip Full Duplex Ethernet Controller Chapter 2 Overview A unique architecture allows the LAN91C93I to combine high performance, flexibility, high integration and simple software interface. The LAN91C93I incorporates the LAN91C92 functionality for local bus environments. The LAN91C93I consists of the same logical I/O register structure in local bus modes. The MMU (Memory Management Unit) architecture used by the LAN91C93I combines the simplicity and low overhead of fixed areas with the flexibility of linked lists providing improved performance over other methods. Packet reception and transmission are determined by memory availability. All other resources are always available if memory is available. To complement this flexible architecture, bus interface functions are incorporated in the LAN91C93I, as well as a 6144 byte packet RAM - and serial EEPROM-based setup. The user can select or modify configuration choices. The LAN91C93I integrates most of the 802.3 functionality, incorporating the MAC layer protocol, the physical layer encoding and decoding functions with the ability to handle the AUI interface. For twisted pair networks, LAN91C93I integrates the twisted pair transceiver as well as the link integrity test functions. The LAN91C93I is a true 10BASE-T single chip device able to interface to a system or a local bus. Support for direct-driven LEDs for installation and run-time diagnostics is provided. 802.3 statistics are gathered to facilitate network management. The LAN91C93I is a single chip Ethernet controller designed to be 100% software compatible with the LAN91C92, LAN91C94 and LAN91C96 in local bus mode. The LAN91C93I has been designed to support full duplex switched Ethernet and provides Fully independent transmit and receive operations. The LAN91C93I internal packet memory is extended to 6k bytes, and the MMU will continue to manage memory in 256 byte pages. The increase in memory size accommodates the potential for simultaneous transmit and receive traffic in some full duplex applications as well as support for enhanced performance on systems that introduce increased latency. The LAN91C93I has the ability to retrieve configuration information from a serial EEPROM on reset or powerup. In local bus mode, the serial EEPROM acts as storage of configuration and IEEE Ethernet address information compatible with the existing LAN91C90, LAN91C92, LAN91C94, and LAN91C96 local bus Ethernet controllers. External Flash ROM is required for CIS storage. The LAN91C93I offers: High integration: Single chip controller including: - - - - - Packet RAM local bus interface EEPROM interface Encoder/decoder with AUI interface 10BASE-T transceiver High performance: Chained ("Back-to-back") packet handling with no CPU intervention: - Queues transmit packets SMSC DS - LAN91C93I Page 7 DATASHEET Rev. 09/30/2002 Non-PCI Single-Chip Full Duplex Ethernet Controller - - - - Queues receive packets Stores results in memory along with packet Queues interrupts Optional single interrupt upon completion of transmit chain Fast block move operation for load/unload: - CPU sees packet bytes as if stored continuously. - Handles 16 bit transfers regardless of address alignment. - Access to packet through fixed window. Fast bus interface: Compatible with local bus type and faster buses. Flexibility: Flexible packet and header processing: - Can be set to Simultasking - Early Receive and Transmit modes. With enhanced Early Receive functions. - Can access any byte in the packet. - Can immediately remove undesired packets from queue. - Can move packets from receive to transmit queue. - Can alter receive processing order without copying data. - Can discard or enqueue again a failed transmission. Resource allocation: - Memory dynamically allocated for transmit and receive. - Can automatically release memory on successful transmission. Configuration: local bus: - Uses non-volatile jumperless setup via serial EEPROM. - nROM on LAN91C93I, is left open with a pullup. This pin is sampled at the end of RESET. Rev. 09/30/2002 Page 8 DATASHEET SMSC DS - LAN91C93I Non-PCI Single-Chip Full Duplex Ethernet Controller Chapter 3 Pin Configurations 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 VDD A19 A18 A17 A16 A15 A14 A13 A12 A11 VDD A10 A9 A8 A7 A6 A5 A4 A3 VSS Pin Configuration LAN91C93I 100 Pin QFP 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 A2 A1 A0 NC nSBHE NC nIOCS16 VSS VDD NC INTR NC VSS D15 D14 D13 D12 VDD D11 D10 D9 D8 VSS EESK EECS EEDI EEDO ENEEP VSS IOS2 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 AVDD COLN COLP RECN RECP TPERXN TPERXP AVSS AVSS NC RBIAS AVDD VDD VSS nROM XTAL1 XTAL2 IOS0 IOS1 VDD nIORD nIOWR nMEMR AEN IOCHRDY VSS D0 D1 D2 D3 VDD D4 D5 D6 D7 VSS RESET VSS nBSELED nLNKLED nRXLED nTXLED AVDD TPETXDP TPETXN TPETXDN TPETXP TXN TXP AVSS Figure 3.1 - Pin Configuration of LAN91C93I QFP SMSC DS - LAN91C93I Page 9 DATASHEET Rev. 09/30/2002 Non-PCI Single-Chip Full Duplex Ethernet Controller 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 nIOWR nIORD VDD A19 A18 A17 A16 A15 A14 A13 A12 A11 VDD A10 A9 A8 A7 A6 A5 A4 A3 VSS A2 A1 A0 Pin Configuration LAN91C93I 100 Pin TQFP 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 NC nSBHE NC nIOCS16 VSS VDD NC INTR NC VSS D15 D14 D13 D12 VDD D11 D10 D9 D8 VSS EESK EECS EEDI EEDO ENEEP TXN TXP AVSS AVDD COLN COLP RECN RECP TPERXN TPERXP AVSS AVSS NC RBIAS AVDD VDD VSS nROM XTAL1 XTAL2 IOS0 IOS1 VDD IOS2 VSS nMEMR AEN IOCHRDY VSS D0 D1 D2 D3 VDD D4 D5 D6 D7 VSS RESET VSS nBSELED nLNKLED nRXLED nTXLED AVDD TPETXDP TPETXN TPETXDN TPETXP Figure 3.2 - Pin Configuration of LAN91C93I TQFP Rev. 09/30/2002 Page 10 DATASHEET SMSC DS - LAN91C93I Non-PCI Single-Chip Full Duplex Ethernet Controller RBIAS COLN COLP RECP RECN TXP TXN TPERXP TPERXN TPETXDP TPETXDN TPETXP 4 ENEEP INTR LAN91C93I IOS2 IOS1 IOS0 EEDI EECS PROM DATA 3 ADDRESS A0-19 D0-15 nMEMR AEN 20 MHz XTAL1 RESET nSBHE nIORD, nIOWR, nROM XTAL2 nIOCS16 EESK IOCHRDY EEDO 4 EEPROM SERIAL BUFFER SYSTEM BUS nIRQ DATASHEET Rev. 09/30/2002 Page 11 SMSC DS - LAN91C93I TPETXN DIAGNOSTIC LEDs AUI 10BASET CABLE SIDE Figure 3.3 - System Diagram for Local Bus with Boot Prom Non-PCI Single-Chip Full Duplex Ethernet Controller 3.1 Local Bus Pin Requirements FUNCTION SYSTEM ADDRESS BUS SYSTEM DATA BUS SYSTEM CONTROL BUS SERIAL EEPROM CRYSTAL OSC. POWER GROUND 10BASE-T interface AUI interface LEDs MISC. NC Rev. 09/30/2002 LOCAL BUS A0 A1-9 A10 A11 A12-14 A15 A16-18 A19 AEN D0-15 RESET nIORD nIOWR nMEMR IOCHRDY nIOCS16 nSBHE INTR EEDI EEDO EECS EESK ENEEP IOS0 IOS1 IOS2 XTAL1, XTAL2 VDD, AVDD VSS, AVSS TPERXP TPERXN TPETXP TPETXN TPETXDP TPETXDN RECP RECN COLP COLN TXP TXN nLNKLED nRXLED nBSELED nTXLED RBIAS nROM MAX NUMBER OF PINS 21 NC 16 8 8 2 10 12 6 6 4 2 5 Page 12 DATASHEET SMSC DS - LAN91C93I Non-PCI Single-Chip Full Duplex Ethernet Controller Chapter 4 Description of Pin Functions PIN NO. PIN NAME nROM TQFP QFP 43 45 76-78 80-87 89-97 78-80, 8289 A0-10 91-99 A11-19 2 4 AEN 74 76 nSBHE 3 5 IOCHRDY 5-8 1013 57-60 62-65 15 7-10, 1215, 59-62, 64-67 17 68 72 70 74 INTR nIOCS16 99 1 nIORD 100 2 nIOWR 1 3 nMEMR 55 57 EESK 54 52 53 56 54 55 EECS EEDO EEDI SMSC DS - LAN91C93I D0-15 RESET TYPE I/O4 with pullup I ** I ** I with pullup ** I with pullup ** OD24 with pullup I/O24 IS with pullup ** O24 OD24 IS with pullup ** IS with pullup ** IS with pullup ** O4 O4 O4 I with pulldown ** DESCRIPTION This pin is sampled at the end of RESET. For local bus operation this pin is left open and it is used as a ROM chip select output that goes active when nMEMR is low and the address bus contains a valid ROM address. Input address lines 0 through 10. Input address lines 11 through 19. Local bus - Address enable input. Used as an address qualifier. Address decoding is only enabled when AEN is low. Local bus - Byte High Enable input. Asserted (low) by the system to indicate a data transfer on the upper data byte. Local bus - Output. Optionally used by the LAN91C93I to extend host cycles. Bi-directional. 16 bit data bus used to access the LAN91C93I internal registers. The data bus has weak internal pullups. Supports direct connection to the system bus without external buffering. Input. Active high Reset. This input is not considered active unless it is active for at least 100ns to filter narrow glitches. Local bus - Active high interrupt signal. Local bus - Active low output asserted in 16 bit mode when AEN is low and A4-A15 decode to the LAN91C93I address programmed into the high byte of the Base Address Register. Local bus, - Input. Active low read strobe used to access the LAN91C93I IO space. Local bus - Input. Active low write strobe used to access the LAN91C93I IO space. Local bus - Active low signal used by the host processor to read from the external ROM. Output. 4usec clock used to shift data in and out of a serial EEPROM. Output. Serial EEPROM chip select. Output. Connected to the DI input of the serial EEPROM. Input. Connected to the DO output of the serial EEPROM. Page 13 DATASHEET Rev. 09/30/2002 Non-PCI Single-Chip Full Duplex Ethernet Controller PIN NO. PIN NAME IOS0-1 TQFP QFP 46,47 48,49 49 51 IOS2 20 17 22 19 nTXLED nBSELED 19 18 51 21 20 53 nRXLED nLNKLED ENEEP 44 46 XTAL1 45 47 XTAL2 Iclk 33 32 35 34 RECP/ RECN 27 26 31 30 29 28 33 32 TXP TXN COLP COLN 35 34 37 36 TPERXP TPERXN 25 23 22 24 27 25 24 26 39 41 TPETXP TPETXN TPETXDP TPETXD N RBIAS Diff. Input ** Diff. Output Diff. Input ** Diff. Input ** Diff. Output Diff. Output 61,70, 98,9, 48,88,41 21,29, 40 63, 72 ,90,100, 11,50,43 Rev. 09/30/2002 23,31, 42 TYPE I with pullup I with pullup ** OD16 OD16 OD16 OD16 I with pullup ** Iclk ** Analog Input DESCRIPTION Input. External switches can be connected to these lines to select between predefined EEPROM configurations. The values of these pins are readable. Input. External switches can be connected to these lines to select between predefined EEPROM configurations. The values of these pins are readable. Transmit LED output. Board Select LED activated by accesses to I/O space (nIORD or nIOWR active with AEN low and valid address decode for local bus). The pulse is stretched beyond the access duration to make the LED visible. Receive LED output. Link LED output. Input. This active high input enables the EEPROM to be read or written by the LAN91C93I. Internally pulled up. Must be connected to ground if no serial EEPROM is used. An external parallel resonance 20MHz crystal should be connected across these pins. If an external clock source is used, it should be connected to this pin (XTAL1) and XTAL2 should be left open. An external parallel resonance 20MHz crystal should be connected across these pins. If an external clock source is used, it should be connected to XTAL1 and this pin (XTAL2) should be left open. AUI receive differential inputs. TXP and TXN are the AUI transmit differential outputs. They must be externally pulled up using 150 ohm resistors. AUI collision differential inputs. A collision is indicated by a 10MHz signal at this input pair. 10BASE-T receive differential inputs. INTERNAL ENDEC - 10BASE-T transmit differential outputs. 10BASE-T delayed transmit differential outputs. Used in combination with TPETXP and TPETXN to generate the 10BASE-T transmit pre-distortion. VDD A resistor should be connected between this pin and analog ground to determine the receive threshold voltage of TX Receive, AUI Receive, AUI Collision Receive, and AUI transmit voltage. +5.0V power supply pins or 3.3V power supply pins AVDD +5.0V analog power supply pins or 3.3V power supply pins Page 14 DATASHEET SMSC DS - LAN91C93I Non-PCI Single-Chip Full Duplex Ethernet Controller PIN NO. TQFP QFP 50,56, 71,79 4,14,42, 66, 16 28,36, 37 75, 73, 69, 67, 38 52,58,68, 73,81, 6,16, 44, 18, 30,38,39 4.1 PIN NAME VSS TYPE Ground pins. AVSS 40, 77, 75, 71, 69 NC DESCRIPTION Analog ground pins. NC No-Connected pins Buffer Symbols O4 I/O4 O162 O24 OD16 OD24 I/O24 I IS Iclk ** Output buffer with 2mA source and 4mA sink at 5V. Output buffer with 1mA source and 2mA sink at 3.3V Output buffer with 2mA source and 4mA sink at 5V. Output buffer with 1mA source and 2mA sink at 3.3V. Output buffer with 2mA source and 16mA sink at 5V. Output buffer with 1mA source and 8mA sink at 3.3V. Output buffer with 12mA source and 24mA sink at 5V. Output buffer with 6mA source and 12mA sink at 3.3V. Open drain buffer with 16mA sink at 5V. Open drain buffer with 8mA sink at 3.3V. Open drain buffer with 24mA sink at 5V. Open drain buffer with 12mA sink at 3.3V. Bi-directional buffer with 12mA source and 24mA sink at 5V. Bi-directional buffer with 6mA source and 16mA sink at 3.3V. Input buffer with TTL levels. Input buffer with Schmitt Trigger Hysteresis. Clock input buffer. Signal is 5.0V input tolerant when Vcc=3.3V. DC levels and conditions defined in the DC Electrical Characteristics section. SMSC DS - LAN91C93I Page 15 DATASHEET Rev. 09/30/2002 Non-PCI Single-Chip Full Duplex Ethernet Controller DATABUS ARBITER ADDRESS BUS BUS INTERFACE ENDEC CSMA/CD AUI CONTROL MMU TWISTED PAIR 10BASE-T TRANSCEIVER RAM Figure 4.1 - LAN91C93I Internal Block Diagram Rev. 09/30/2002 Page 16 DATASHEET SMSC DS - LAN91C93I Non-PCI Single-Chip Full Duplex Ethernet Controller Chapter 5 Functional Description The LAN91C93I includes an arbitrated-shared memory of 6144 bytes. Any portion of this memory can be used for receive or transmit packets. The MMU unit allocates RAM memory to be used for transmit and receive packets, using 256 byte pages. The arbitration is transparent to the CPU in every sense. There is no speed penalty for local bus type of machines due to arbitration. There are no restrictions on what locations can be accessed at any time. RAM accesses as well as MMU requests are arbitrated. The RAM is accessed by mapping it into I/O space for sequential access. Except for the RAM accesses and the MMU request/release commands, I/O accesses are not arbitrated. The I/O space is 16 bits wide. Provisions for 8 bit systems are handled by the bus interface. In the system memory space, up to 64 kbytes are decoded by the LAN91C93I as expansion ROM. The ROM expansion area is 8 bits wide. Device configuration is done using a serial EEPROM, with support for modifications to the EEPROM at installation time. The CSMA/CD core implements the 802.3 MAC layer protocol. It has two independent interfaces, the data path and the control path. In local bus mode, serial EEPROM is used for configuration and IEEE Node address making it software compatible to the LAN9xxx family of Ethernet LAN Controllers. The EEPROM is optional for local bus requiring a Minimum size of 64 X 16 bit word addresses. Both interfaces are 16 bits wide. The control path provides a set of registers used to configure and control the block. These registers are accessible by the CPU through the LAN91C93I I/O space. The data path is of sequential access nature and typically works in one direction at any given time. An internal DMA type of interface connects the data path to the device RAM through the arbiter and MMU. The CSMA/CD data path interface is not accessible to the host CPU. The internal DMA interface can arbitrate for RAM access and request memory from the MMU when necessary. An encoder/decoder block interfaces the CSMA/CD block on the serial side. The encoder will do the Manchester encoding of the transmit data at 10 Mb/s, while the decoder will recover the receive clock, and decode received data. Carrier and Collision detection signals are also handled by this block and relayed to the CSMA/CD block. The encoder/decoder block can interface the network through the AUI interface pairs, or it can be programmed to use the internal 10BASE-T transceiver and connect to a twisted pair network. The twisted pair interface takes care of the medium dependent signaling for 10BASE-T type of networks. It is responsible for line interface (with external pulse transformers and pre-distortion resistors), collision detection as well as the link integrity test function. The LAN91C93I provides a 16-bit data path into RAM. The RAM is private and can only be accessed by the system via the arbiter. RAM memory is managed by the MMU. Byte and word accesses to the RAM are supported. SMSC DS - LAN91C93I Page 17 DATASHEET Rev. 09/30/2002 Non-PCI Single-Chip Full Duplex Ethernet Controller If the system to SRAM bandwidth is insufficient the LAN91C93I will automatically use its IOCHRDY line for flow control. However, for local bus, IOCHRDY will never be negated. The LAN91C93I consists of an integrated Ethernet controller mapped entirely in I/O space. The Ethernet controller function includes a built-in 6kbyte RAM for packet storage. This RAM buffer is accessed by the CPU through sequential access regions of 256 bytes each. The RAM access is internally arbitrated by the LAN91C93I, and dynamically allocated between transmit and receive packets. Each packet may consist of one or more 256-byte page. The Ethernet controller functionality is identical to the LAN91C94 and LAN91C95 except where indicated otherwise. The LAN91C93I Memory Management Unit parameters are: RAM size Max. number of pages Max. number of packets Max. pages per packet Page Size 5.1 6kbytes 24 24 (FIFOs have 24 entries of 5 bits) 6 256 bytes Buffer Memory The logical addresses for RAM access are divided into TX area and RX area. The TX area is seen by the CPU as a window through which packets can be loaded into memory before queuing them in the TX FIFO of packets. The TX area can also be used to examine the transmit completion status after packet transmission. The RX area is associated to the output of the RX FIFO of packets, and is used to access receive packet data and status information. The logical address is specified by loading the address pointer register. The pointer can automatically increment on accesses. All accesses to the RAM are done via I/O space. A bit in the address pointer also specifies if the address refers to the TX or RX area. In the TX area, the host CPU has access to the next transmit packet being prepared for transmission. In the RX area, it has access to the first receive packet not processed by the CPU yet. The FIFO of packets, existing beneath the TX and RX areas, is managed by the MMU. The MMU dynamically allocates and releases memory to be used by the transmit and receive functions. Rev. 09/30/2002 Page 18 DATASHEET SMSC DS - LAN91C93I 1536 RX AREA 1536 TX AREA RCV VS. TX AREA SELECTION 11-BIT LOGICAL ADDRESS POINTER REGISTER RCV BIT MMU RX PACKET NUMBER MMU TX PACKET NUMBER PHYSICAL MEMORY PAGE = 256 bytes Non-PCI Single-Chip Full Duplex Ethernet Controller Figure 5.1 - Mapping and Paging vs. Receive and Transmit Area SMSC DS - LAN91C93I Page 19 DATASHEET Rev. 09/30/2002 Rev. 09/30/2002 Page 20 DATASHEET TX FIFO TX COMPLETION FIFO FIFO PORTS REGISTER CPU SIDE PACKET NUMBER REGISTER PACKET #C DATA COUNT STATUS DATA COUNT STATUS DATA LINEAR ADDRESS TO CSMA PACKET #B PACKET #A COUNT STATUS MMU MAPPING C B C A B MEMORY Non-PCI Single-Chip Full Duplex Ethernet Controller Figure 5.2 - Transmit Queues and Mapping SMSC DS - LAN91C93I LINEAR ADDRESS CSMA FROM SIDE CPU REGISTER FIFO PORTS RX FIFO PACKET #E DATA COUNT STATUS PACKET #D DATA COUNT STATUS MMU MAPPING E D E D MEMORY Non-PCI Single-Chip Full Duplex Ethernet Controller Figure 5.3 - Receive Queues and Mapping SMSC DS - LAN91C93I Page 21 DATASHEET Rev. 09/30/2002 Non-PCI Single-Chip Full Duplex Ethernet Controller EEPROM INTERFACE Control Control Control Control Address 8-16 bit Bus Interface Unit Control ENDEC Control AUI Arbiter MMU Ethernet Protocol Handler DMA TX/RX FIFO Pointer (EPH) TPO WR FIFO Data RD FIFO TX Data TX Data 6K Byte SRAM Twisted Pair Transceiver TPI RX Data RX Data Figure 5.4 - LAN91C93I Internal Block Diagram with Data Path Rev. 09/30/2002 Page 22 DATASHEET SMSC DS - LAN91C93I SMSC DS - LAN91C93I Page 23 DATASHEET DATA REGISTER (FIFOS) POINTER REGISTER READ REG READ DATA PACKET # RX FIFO PACKET NUMBER DATA RAM ADDRESS PHYSICAL ADDRESS MMU LOGICAL ADDRESS CPU/nLAN (FROM ARBITER) RCV TX (PACKET NUMBER REG) POINTER REGISTER & COUNTER WRITE DATA WRITE REG LATCH READ POINTER INC LOAD TX COMPLETION FIFO TX FIFO PNR DMA DATA ADDRESS T/nR PACKET # RX FIFO CSMA/CD Non-PCI Single-Chip Full Duplex Ethernet Controller Figure 5.5 - Logical Address Generation and Relevant Registers Rev. 09/30/2002 Non-PCI Single-Chip Full Duplex Ethernet Controller Table 5.1 - LAN91C93I Address Space Ethernet I/O space (1) SIGNALS USED nIORD/ nIOWR LOCAL BUS Y ONCHIP Y DEPTH WIDTH 16 locations 8 or 16 bits Table 5.2 - Bus Transactions in Local Bus Mode 8 BIT MODE (16BIT=0)) 16 BIT MODE A0 0 NSBHE X D0-7 Even byte D8-15 - 1 0 X 0 Odd byte Even byte Odd byte 0 1 1 1 0 1 Even byte - Odd byte Otherwise 5.2 Invalid cycle 16 BIT: CONFIGURATION REGISTER bit 7 8 Bit mode: (nMIS16 = 1) Interrupt Structure The Ethernet interrupt is conceptually equivalent to the LAN91C94 interrupt line, it is the or function of all enabled interrupts within the Ethernet core. Table 5.3 - Interrupt Merging FUNCTION Interrupt Output Ethernet Interrupt Source Ethernet Interrupt Enable 5.3 LOCAL BUS MODE INTR OR function of all interrupt bits specified in the Interrupt Status Register ANDed with their respective Enable bits Not Applicable in local bus mode Reset Logic The pins and bits involved in the different reset mechanisms are: RESET - Input Pin SOFT RST - EPH Soft Reset bit in RCR Rev. 09/30/2002 Page 24 DATASHEET SMSC DS - LAN91C93I Non-PCI Single-Chip Full Duplex Ethernet Controller Table 5.4 - Reset Logic RESETS THE FOLLOWING FUNCTIONS RESET pin SOFT RST 5.4 All internal logic The Ethernet controller itself except for the IA, CONF and BASE registers. SAMPLES LOCAL BUS MODE Yes No TRIGGERS EEPROM READ Yes No Power Down Logic States The following tables describe the power down states of the LAN91C93I. The bits involved in power down are: PWRDN - Legacy power down bit in Control Register LAN91C93I Power Down States Table 5.5 - Local Bus Mode Defined States (Refer To Table 5.6 For Next States To Wake-Up Events) CURRENT STATE NO. CTR PWRDWN BIT 1 2 X 0 Everything. 3 4 0 1 Ethernet Tx Ethernet Tx, Rx, Link 5 1 Ethernet Tx, Rx, Link DOES NOT POWER DOWN POWERS DOWN Ethernet Tx, Rx, Link Ethernet Rx, Link Table 5.6 - Local Bus Mode NO. 1 WAKES UP BY NEXT STATE CTR PWR-DWN BIT CTR WAKEUP_EN BIT 0 0 2 By writing a 0 to CTR PWRDWN bit = 0 0 0 3 By writing 0 to CTR PWRDWN bit 0 0 SMSC DS - LAN91C93I Page 25 DATASHEET COMMENTS Fully Awake The CTR PWRDWN bit has precedence unlike the LAN91C95 Rev. 09/30/2002 Non-PCI Single-Chip Full Duplex Ethernet Controller Chapter 6 Packet Format in Buffer Memory for Ethernet The packet format in memory is similar to that in the TRANSMIT and RECEIVE areas. The first word is reserved for the status word, the next word is used to specify the total number of bytes, and that in turn is followed by the data area. The data area holds the packet itself, and its length is determined by the byte count. The packet memory format is word oriented. RAM OFFSET (DECIMAL) bit0 bit15 2nd Byte 1st Byte 0 2 STATUS WORD BYTE COUNT (always even) RESERVED 4 DATA AREA 1534 Max CONTROL BYTE LAST DATA BYTE (if odd) Last Byte Figure 6.1 - Data Packet Format STATUS WORD BYTE COUNT DATA AREA CONTROL BYTE TRANSMIT PACKET RECEIVE PACKET Written by CSMA upon transmit Written by CSMA upon receive completion (see Status Register) completion (see RX Frame Status Word) Written by CPU Written by CSMA Written/modified by CPU Written by CSMA Written by CPU to control Written by CSMA. Also has ODD/EVEN data bytes ODD/EVEN bit BYTE COUNT - Divided by two, it defines the total number of words, including the STATUS WORD, the BYTE COUNT WORD, the DATA AREA and the CONTROL BYTE. The receive byte count always appears as even, the ODDFRM bit of the receive status word indicates if the low byte of the last word is Rev. 09/30/2002 Page 26 DATASHEET SMSC DS - LAN91C93I Non-PCI Single-Chip Full Duplex Ethernet Controller relevant. The transmit byte count least significant bit will be assumed 0 by the controller regardless of the value written in memory. The maximum size of the frame can be stored in 6 pages (256 bytes per page), the maximum BYTE COUNT number is 1536. DATA AREA (in RAM) The data area starts at offset 4 of the packet structure, and it can extend for up to 1531 bytes. The data area contains six bytes of DESTINATION ADDRESS followed by six bytes of SOURCE ADDRESS, followed by a variable length number of bytes. On transmit, all bytes are provided by the CPU, including the source address. The LAN91C93I does not insert its own source address. On receive, all bytes are provided by the CSMA side. The 802.3 Frame Length word (Frame Type in Ethernet) is not interpreted by the LAN91C93I. It is treated transparently as data for both transmit and receive operations. CONTROL BYTE (in RAM) The CONTROL BYTE always resides on the high byte of the last word. CONTROL BYTE is written by the CPU as: X X ODD CRC 0 0 0 For transmit packets the 0 ODD - If set, indicates an odd number of bytes, with the last byte being right before the CONTROL BYTE. If clear, the number of data bytes is even and the byte before the CONTROL BYTE is not transmitted. CRC - When set, CRC will be appended to the frame. This bit has only meaning if the NOCRC bit in the TCR is set. For receive packets the CONTROL BYTE is written by the controller as: 0 1 ODD 0 0 0 0 0 ODD - If set, indicates an odd number of bytes, with the last byte being right before the CONTROL BYTE. If clear, the number of data bytes is even and the byte before the CONTROL BYTE should be ignored. RECEIVE FRAME STATUS WORD (in RAM) This word is written at the beginning of each receive frame in memory. It is not available as a register. ALGN ERR BROD CAST BADCRC ODDFRM TOOLNG TOO SHORT MULT CAST HASH VALUE 5 4 3 2 1 0 ALGNERR - Frame had alignment error. BRODCAST - Receive frame was broadcast. BADCRC - Frame had CRC error. SMSC DS - LAN91C93I Page 27 DATASHEET Rev. 09/30/2002 Non-PCI Single-Chip Full Duplex Ethernet Controller ODDFRM - This bit when set indicates that the received frame had an odd number of bytes. TOOLNG - The received frame is longer than the 802.3 maximum size (1518 bytes on the cable). TOOSHORT - The received frame is shorter than the 802.3 minimum size (64 bytes on the cable). HASH VALUE - Provides the hash value used to index the Multicast Registers. Can be used by receive routines to speed up the group address search. The hash value consists of the six most significant bits of the CRC calculated on the Destination Address, and maps into the 64 bit multicast table. Bits 5,4,3 of the hash value select a byte of the multicast table, while bits 2,1,0 determine the bit within the byte selected. Examples of the address mapping are shown in the table below: ED 0D 01 2F ADDRESS 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 HASH VALUE 5-0 000 000 010 000 100 111 111 111 MULTICAST TABLE BIT MT-0 bit 0 MT-2 bit 0 MT-4 bit 7 MT-7 bit 7 MULTCAST - Receive frame was multicast. If hash value corresponds to a multicast table bit that is set, and the address was a multicast, the packet will pass address filtering regardless of other filtering criteria. Rev. 09/30/2002 Page 28 DATASHEET SMSC DS - LAN91C93I Non-PCI Single-Chip Full Duplex Ethernet Controller Chapter 7 Registers Map in I/O Space 16 Bit Registers 16 Bit Registers 16 Bit Registers 16 Bit Registers BANK0 BANK1 BANK2 0 TCR CONFIG MMU COMMAND 2 EPH STATUS BASE 4 RCR (INDIVIDUAL ADDRESS) IA 0-1 FIFO PORTS 6 COUNTER IA 2-3 POINTER 8 MIR A MCR C RESERVED IA 4-5 PNR ARR BANK3 BANK4 ECOR (LOW BYTE) ECSR (HIGH BYTE) MULTICAST TABLE DATA MGMT GENERAL PURPOSE DATA REVISION CONTROL INTERRUPT ERCV BANK SELECT REGISTER E 16 Bit Registers BANK SELECT BANK2 Register used during run time. Non volatile, stored in EEPROM. Figure 7.1 - LAN91C93I Registers 7.1 I/O Space Access The address is determined by the Ethernet I/O Base Registers. The Ethernet I/O space can be configured as an 8 or 16 bit I/O space, and is similar to the LAN91C94, LAN91C92, etc. I/O space mapping. To limit the I/O space requirements to 16 locations, the registers are Split into 4 banks in LOCAL BUS mode. The last word of the I/O area is shared by all banks and can be used to change the bank in use. Banks 0 through 3 functionally correspond to the LAN91C94 banks. SMSC DS - LAN91C93I Page 29 DATASHEET Rev. 09/30/2002 Non-PCI Single-Chip Full Duplex Ethernet Controller Registers are described using the following convention: OFFSET E BIT 15 RST Val BIT 7 RST Val BIT14 RST Val BIT 6 RST Val NAME BANK SELECT REGISTER BIT 13 RST Val BIT 5 RST Val BIT 12 RST Val BIT 4 RST Val TYPE SYMBOL READ/WRITE BSR BIT 11 RST Val BIT 3 RST Val BIT 10 RST Val BIT 2 RST Val BIT9 RST Val BIT 1 RST Val BIT8 RST Val BIT 0 RST Val OFFSET - Defines the address offset within the IOBASE where the register can be accessed at, provided the bank select has the appropriate value. The offset specifies the address of the even byte (bits 0-7) or the address of the complete word. The odd byte can be accessed using address (offset + 1). Some registers (e.g. the Interrupt Ack. or the Interrupt Mask) are functionally described as two eight bit registers. In such case, the offset of each one is independently specified. Regardless of the functional description, when the LAN91C93I is in 16 bit mode, all registers can be accessed as words or bytes. RST Val - The default bit values upon hard reset are highlighted below each register. 7.2 I/O Space Registers Description 7.2.1 Bank Select Register OFFSET NAME BANK SELECT REGISTER # IN HEX TYPE SYMBOL READ/WRITE BSR 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 BS2 BS1 BS0 0 0 0 X X X X X BS2, BS1, BS0 - Determine the bank presently in use. This register is always accessible except in power down mode and is used to select the register bank in use. The upper byte always reads as 33h and can be used to help determine the I/O location of the LAN91C93I. Rev. 09/30/2002 Page 30 DATASHEET SMSC DS - LAN91C93I Non-PCI Single-Chip Full Duplex Ethernet Controller The BANK SELECT REGISTER is always accessible regardless of the value of BS0-2. Accesses to non-existing banks will ignore writes and reads will return 0x33 on byte reads. BS2 0 0 0 0 1 BS1 0 0 1 1 X BSO 0 1 0 1 X BANK# 0 1 2 3 None I/O SPACE - BANK0 OFFSET 0 NAME TRANSMIT CONTROL REGISTER TYPE READ/WRITE SYMBOL TCR This register holds bits programmed by the CPU to control some of the protocol transmit options. FDSE ETENTYPE 0 PAD_EN 0 0 EPH LOOP 0 STP SQET 0 X X X FDUPLX 0 TXP_EN 0 MON_ CSN 0 FORCOL 0 NOCRC X LOOP 0 0 TXENA 0 NOCRC - Does not append CRC to transmitted frames when set, allows software to insert the desired CRC. Defaults to zero, namely CRC inserted. FDSE - Full Duplex Switched Ethernet. When set, the LAN91C93I is configured for Full Duplex Switched Ethernet, it defaults clear to normal CSMA/CD protocol. In FDSE mode the LAN91C93I transmit and receive processes are fully independent, namely no deferral and no collision detection are implemented. When FDSE is set, FDUPLX is internally assumed high and MON_CSN is assumed low regardless of their actual values. ETEN-TYPE - Early transmit underrun function type. When low, ETEN bit in the PTR register will enable the Early transmit underrun function as it was implemented in the LAN91C94. I.e. "The Early Transmit function allows the CPU to enqueue the first transmit packet before it is fully loaded in packet memory. The loading operation proceeds in parallel with the transmission, and in the case that the transmitter gets ahead of the CPU, the LAN91C93I will prevent the transmission of erroneous data by forcing an Underrun condition. Underruns will be triggered by starving the transmit DMA if the LAN91C93I detects that the DMA TX address exceeds the pointer address." With ETEN -TYPE set to one (1), ETEN bit set to one (1) in the pointer register will mean the following: "For underrun detection purposes the RAM logical address and packet numbers of the packet being loaded are compared against the logical address and packet numbers of the packet being transmitted. If the packet numbers match and the logical address of the packet being transmitted exceeds the address being loaded, the LAN91C93I will prevent the transmission of erroneous data by forcing an Underrun condition. Underruns will be triggered by starving the transmit DMA if the LAN91C93I detects that the DMA TX address exceeds the pointer address." EPH_LOOP - Internal loopback at the EPH block. Does not exercise the encoder decoder. Serial data is looped back when set. Defaults low. SMSC DS - LAN91C93I Page 31 DATASHEET Rev. 09/30/2002 Non-PCI Single-Chip Full Duplex Ethernet Controller STP_SQET - Stop transmission on SQET error. If set, stops and disables transmitter on SQE test error. Does not stop on SQET error and transmits next frame if clear. Defaults low. FDUPLX - When set it enables full duplex operation. This will cause frames to be received if they pass the address filter regardless of the source for the frame. When clear the node will not receive a frame sourced by itself. Clearing this bit (Normal Operation), allows in promiscuous mode, not to receive it's own packet. TXP_EN - This bit is reserved and should always be set to 0 on the LAN91C93I. MON_CSN - When set the LAN91C93I monitors carrier while transmitting. It must see its own carrier by the end of the preamble. If it is not seen, or if carrier is lost during transmission, the transmitter aborts the frame without CRC and turns itself off. When this bit is clear the transmitter ignores its own carrier. Defaults low. PAD_EN - When set, the LAN91C93I will pad transmit frames shorter than 64 bytes with 00. For TX, CPU should write the actual BYTE COUNT before padded by the LAN91C93I to the buffer RAM, excludes the padded 00. When this bit is cleared, the LAN91C93I does not pad frames. FORCOL - When set the transmitter will force a collision by not deferring deliberately. After the collision this bit is reset automatically. This bit defaults low to normal operation. LOOP - Local Loopback. When set, transmit frames are internally looped to the receiver after the encoder/decoder. Collision and Carrier Sense are ignored. No data is sent out. Defaults low to normal mode. TXENA - Transmit enabled when set. Transmit is disabled if clear. When the bit is cleared the LAN91C93I will complete the current transmission before stopping. When stopping due to an error, this bit is automatically cleared. Table 7.1- Transmit Loop AUI FDSE FDUPLX EPH_LOOP LOOP LOOPS AT X X X 1 X EPH Block 1 0 X 0 0 0 1 1 0 0 0 0 0 0 0 X 1 1 0 0 Cable 10BASE-T Driver NORMAL CSMA/CD No Loopback FULL DUPLEX SWITCHED ETHERNET - No loopback and No SQET TRANSMITS TO NETWORK No Yes Yes Yes Yes I/O SPACE - BANK0 OFFSET 2 NAME EPH STATUS REGISTER TYPE READ ONLY SYMBOL EPHSR This register stores the status of the last transmitted frame. This register value, upon individual transmit packet completion, is stored as the first word in the memory area allocated to the packet. Packet interrupt processing should use the copy in memory as the register itself will be updated by subsequent packet transmissions. The register can be used for real time values (like TXENA and LINK OK). If TXENA is cleared the register holds the last packet completion status. Rev. 09/30/2002 Page 32 DATASHEET SMSC DS - LAN91C93I Non-PCI Single-Chip Full Duplex Ethernet Controller TX UNRN 0 TX DEFR 0 LINK_ OK 0 LTX BRD 0 0 CTR _ROL 0 SQET 16COL 0 0 RES EXC _DEF 0 LTX MULT 0 LOST CARR 0 MUL COL 0 LATCOL 0 SNGL COL 0 X TX_SUC 0 TXUNRN - Transmit Under run. Set if Under run occurs, it also clears TXENA bit in TCR. Cleared by setting TXENA high. This bit should never be set under normal operation. LINK_OK - State of the 10BASE-T Link Integrity Test. A transition on the value of this bit generates an interrupt when the LE ENABLE bit in the Control Register is set. RES - This bit is reserved and will always return a zero(0). CTR_ROL - Counter Roll over. When set one or more 4 bit counters have reached maximum count (15). Cleared by reading the ECR register. EXC_DEF - Excessive deferral. When set last/current transmit was deferred for more than 1518 * 2 byte times. Cleared at the end of every packet sent. LOST_CARR - Lost carrier sense. When set indicates that Carrier Sense was not present at end of preamble. Valid only if MON_CSN is enabled. This condition causes TXENA bit in TCR to be reset. Cleared by setting TXENA bit in TCR. LATCOL - Late collision detected on last transmit frame. If set a late collision was detected (later than 64 byte times into the frame). When detected the transmitter JAMs and turns itself off clearing the TXENA bit in TCR. Cleared by setting TXENA in TCR. TX_DEFR - Transmit Deferred. When set, carrier was detected during the first 6.4 uSec of the inter frame gap. Cleared at the end of every packet sent. LTX_BRD - Last transmit frame was a broadcast. Set if frame was broadcast. Cleared at the start of every transmit frame. SQET - Signal Quality Error Test. The transmitter opens a 1.6 us window 0.8 us after transmission is completed and the receiver returns inactive. During this window, the transmitter expects to see the SQET signal from the transceiver. The absence of this signal is a 'Signal Quality Error' and is reported in this status bit. Transmission stops and EPH INT is set if STP_SQET is in the TCR is also set when SQET is set. This bit is cleared by setting TXENA high. 16COL - 16 collisions reached. Set when 16 collisions are detected for a transmit frame. TXENA bit in TCR is reset. Cleared when TXENA is set high. LTX_MULT - Last transmit frame was a multicast. Set if frame was a multicast. Cleared at the start of every transmit frame. MULCOL - Multiple collision detected for the last transmit frame. Set when more than one collision was experienced. Cleared when TX_SUC is high at the end of the packet being sent. SNGLCOL - Single collision detected for the last transmit frame. Set when a collision is detected. Cleared when TX_SUC is high at the end of the packet being sent. TX_SUC - Last transmit was successful. Set if transmit completes without a fatal error. This bit is cleared by the start of a new frame transmission or when TXENA is set high. SMSC DS - LAN91C93I Page 33 DATASHEET Rev. 09/30/2002 Non-PCI Single-Chip Full Duplex Ethernet Controller Fatal errors are: 16 collisions SQET fail and STP_SQET = 1 FIFO Underrun Carrier lost and MON_CSN = 1 Late collision I/O SPACE - BANK0 OFFSET 4 SOFT RST 0 0 NAME RECEIVE CONTROL REGISTER FILT CAR 0 0 TYPE READ/WRITE SYMBOL RCR 0 0 0 0 0 0 0 0 STRIP CRC 0 ALMUL PRMS 0 0 0 0 0 RXEN 0 RX_ ABORT 0 SOFT_RST - Software activated Reset. Active high. Initiated by writing this bit high and terminated by writing the bit low. The LAN91C93I configuration is not preserved, except for Configuration, Base, and IA05 Registers. The EEPROM in LOCAL BUS mode is not reloaded after software reset. FILT_CAR - Filter Carrier. When set filters leading edge of carrier sense for 12 bit times. Otherwise recognizes a receive frame as soon as carrier sense is active. STRIP_CRC - When set it strips the CRC on received frames. When clear the CRC is stored in memory following the packet. Defaults low. RXEN - Enables the receiver when set. If cleared, completes receiving current frame and then goes idle. Defaults low on reset. ALMUL - When set accepts all multicast frames (frames in which the first bit of DA is '1'). When clear accepts only the multicast frames that match the multicast table setting. Defaults low. PRMS - Promiscuous mode. When set receives all frames. Change vs. LAN91C92: Does not receive its own transmission when not in full duplex (FDUPLX)!. RX_ABORT - This bit is set if a receive frame was aborted due to length longer than 1532 bytes. The frame will not be received. The bit is cleared by RESET or by the CPU writing it low. I/O SPACE - BANK0 OFFSET 6 NAME COUNTER REGISTER TYPE READ ONLY SYMBOL ECR Counts four parameters for MAC statistics. When any counter reaches 15 an interrupt is issued. All counters are cleared when reading the register, and do not wrap around beyond 15. Rev. 09/30/2002 Page 34 DATASHEET SMSC DS - LAN91C93I Non-PCI Single-Chip Full Duplex Ethernet Controller NUMBER OF EXC. DEFERRED TX 0 0 0 MULTIPLE COLLISION COUNT 0 0 0 0 0 0 0 NUMBER OF DEFERRED TX 0 0 SINGLE COLLISION COUNT 0 0 0 0 Each four bit counter is incremented every time the corresponding event, as defined in the EPH STATUS REGISTER bit description, occurs. Note that the counters can only increment once per enqueued transmit packet, never faster, limiting the rate of interrupts that can be generated by the counters. For example if a packet is successfully transmitted after one collision the SINGLE COLLISION COUNT field is incremented by one. If a packet experiences between 2 to 16 collisions, the MULTIPLE COLLISION COUNT field is incremented by one. If a packet experiences deferral the NUMBER OF DEFERRED TX field is incremented by one, even if the packet experienced multiple deferrals during its collision retries. The COUNTER REGISTER facilitates maintaining statistics in the AUTO RELEASE mode where no transmit interrupts are generated on successful transmissions. Reading the register in the transmit service routine will be enough to maintain statistics. I/O SPACE - BANK0 OFFSET 8 NAME MEMORY INFORMATION REGISTER TYPE READ ONLY SYMBOL MIR For software compatibility with other LAN9000 parts all memory-related information is represented in 256 x M byte units, where the multiplier M is determined by the MCR upper byte. M equals "1" for the LAN91C93I. 0 0 0 0 FREE MEMORY AVAILABLE (in BYTES* 256* M) 0 1 1 0 MEMORY SIZE (in BYTES* 256* M) 0 1 1 0 0 0 0 0 FREE MEMORY AVAILABLE - This register can be read at any time to determine the amount of free memory. The register defaults to the MEMORY SIZE upon reset or upon the RESET MMU command. MEMORY SIZE - This register can be read to determine the total memory size, and will always read 18H (6144 bytes) for the LAN91C93I. LAN91C90 LAN91C90 LAN91C92/ LAN91C94 LAN91C95 LAN91C96 LAN91C93I LAN91C100 SMSC DS - LAN91C93I MEMORY SIZE REGISTER FFH 40H 12H M 1 1 1 ACTUAL MEMORY 64 kbytes 16 kbytes 4608 bytes 18H 18H 18H FFH 1 1 1 2 6144 bytes 6144 bytes 6144 bytes 128 kbytes Page 35 DATASHEET Rev. 09/30/2002 Non-PCI Single-Chip Full Duplex Ethernet Controller I/O SPACE - BANK0 OFFSET A NAME MEMORY CONFIGURATION REGISTER TYPE lower byte READ/WRITE upper byte READ ONLY SYMBOL MCR Memory Size Multiplier "M" 0 0 0 0 1 1 0 0 Memory Reserved for Transmit (in BYTES * 256 * M) 0 0 0 0 1 1 0 0 MEMORY RESERVED FOR TRANSMIT Programming this value allows the host CPU to reserve memory to be used later for transmit, limiting the amount of memory that receive packets can use up. When programmed for zero, the memory allocation between transmit and receive is completely dynamic. When programmed for a non-zero value, the allocation is dynamic if the free memory exceeds the programmed value, while receive allocation requests are denied if the free memory is less or equal to the programmed value. This register defaults to zero upon reset. It is not affected by the RESET MMU command. The value written to the MCR is a reserved memory space IN ADDITION TO ANY MEMORY CURRENTLY IN USE. If the memory allocated for transmit plus the reserved space for transmit is required to be constant (rather than grow with transmit allocations) the CPU should update the value of this register after allocating or releasing memory. The contents of MIR as well as the low byte of MCR are specified in 256* M bytes. The multiplier M is determined by bits 11, 10 and 9 as follows: DEVICE FEAST LAN91C90 FUTURE FUTURE FUTURE Note 7.1 BIT 11 0 0 0 1 1 BIT 10 1 0 1 0 0 BIT 9 0 1 1 0 1 M 2 1 4 8 16 MAX MEMORY SIZE 256 (Note 7.1) 256 (Note 7.1) 2=128k 256 (Note 7.1) 256 (Note 7.1) 1=64k 256k 512k 1M Bits 11, 10 and 9 are read only bits used by the software driver to transparently run on different controllers of the LAN9000 family. I/O SPACE - BANK1 OFFSET 0 NAME CONFIGURATION REGISTER TYPE READ/WRITE SYMBOL CR The Configuration Register holds bits that define the device configuration and are not expected to change during run-time. This register is part of the EEPROM saved setup in LOCAL BUS mode only. 0 0 16BIT 0 Rev. 09/30/2002 X FULL STEP 0 0 0 NO WAIT X DIS LINK 0 X 1 0 Reserved 1 Page 36 DATASHEET SET SQLCH 0 INTR 0 AUI SELECT 0 X SMSC DS - LAN91C93I Non-PCI Single-Chip Full Duplex Ethernet Controller NO WAIT - When set, does not request additional wait states. An exception to this are accesses to the Data Register if not ready for a transfer. When clear, negates IOCHRDY for two to three 20MHz clocks on any cycle to the LAN91C93I. FULL STEP - This bit is used to select the signaling mode for the AUI port. When set the AUI port uses full step signaling. Defaults low to half step signaling. This bit is only meaningful when AUI SELECT is high. SET SQLCH - When set, the squelch level used for the 10BASE-T receive signal is 240mV. When clear the receive squelch level is 400mV. Defaults low. AUI SELECT - When set the AUI interface is used, when clear the 10BASE-T interface is used. Defaults low. INTR - Always write '0 0' to bits 1 and 2 to enable the interrupt output. 16BIT - This bit defaults low and can be programmed by the host CPU. DIS LINK - This bit is used to disable the 10BASE-T link test functions. When this bit is high the LAN91C93I disables link test functions by not generating nor monitoring the network for link pulses. In this mode the LAN91C93I will transmit packets regardless of the link test, the EPHSR LINK_OK bit will be set and the LINK LED will stay on. When low the link test functions are enabled. If the link status indicates FAIL, the EPHSR LINK_OK bit will be low, while transmit packets enqueued will be processed by the LAN91C93I, transmit data will not be sent out to the cable. I/O SPACE - BANK1 OFFSET 2 NAME BASE ADDRESS REGISTER TYPE READ/WRITE SYMBOL BAR For LOCAL BUS mode only, this register holds the I/O address decode option chosen for the I/O and ROM space. It is part of the EEPROM saved setup, and is not usually modified during run-time. A15 A14 0 0 ROM SIZE 0 1 A13 0 RA18 1 A9 1 RA17 0 A8 1 RA16 0 A7 0 RA15 1 A6 0 RA14 1 A5 0 1 A15 - A13 and A9 - A5 - These bits are compared in LOCAL BUS mode against the I/O address on the bus to determine the IOBASE for LAN91C93I registers. The 64k I/O space is fully decoded by the LAN91C93I down to a 16 location space, therefore the unspecified address lines A4, A10, A11 and A12 must be all zeros. ROM SIZE - Determines the ROM decode area in LOCAL BUS mode memory space as follows: 00 = ROM disable 01 = 16k: RA14-18 define ROM select. 10 = 32k: RA15-18 define ROM select. 11 = 64k: RA16-18 define ROM select. RA18-RA14 - These bits are compared in LOCAL BUS mode against the memory address on the bus to determine if the ROM is being accessed, as a function of the ROM SIZE. ROM accesses are read only memory accesses defined by MEMRD* going low. SMSC DS - LAN91C93I Page 37 DATASHEET Rev. 09/30/2002 Non-PCI Single-Chip Full Duplex Ethernet Controller For a full decode of the address space unspecified upper address lines have to be: A19 = "1", A20-A23 lines are not directly decoded, however LOCAL BUS systems will only activate SMEMRD* only when A20A23=0. All bits in this register are loaded from the serial EEPROM in LOCAL BUS Mode only. The I/O base decode defaults to 300h (namely, the high byte defaults to 18h). ROM SIZE defaults to 01. ROM decode defaults to CC000 (namely the low byte defaults to 67h). Below chart shows the decoding of I/O Base Address 300h: A15 0 A14 0 A13 0 A12 0 A11 0 A10 0 A9 1 A8 1 A7 0 A6 0 A5 0 A4 0 A3 0 A2 0 A1 0 A0 0 I/O SPACE - BANK1 OFFSET 4 THROUGH 9 NAME INDIVIDUAL ADDRESS REGISTERS TYPE READ/WRITE SYMBOL IAR These registers are loaded starting at word location 20h of the EEPROM upon hardware reset or EEPROM reload. The registers can be modified by the software driver, but a STORE operation will not modify the EEPROM Individual Address contents. Bit 0 of Individual Address 0 register corresponds to the first bit of the address on the cable. Rev. 09/30/2002 Page 38 DATASHEET SMSC DS - LAN91C93I Non-PCI Single-Chip Full Duplex Ethernet Controller ADDRESS 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ADDRESS 1 0 0 0 0 0 ADDRESS 2 0 0 0 0 0 ADDRESS 3 0 0 0 0 0 ADDRESS 4 0 0 0 0 0 ADDRESS 5 0 0 0 0 0 I/O SPACE - BANK1 OFFSET A NAME GENERAL ADDRESS REGISTERS 0 0 0 HIGH DATA BYTE 0 0 0 0 0 LOW DATA BYTE 0 0 TYPE READ/WRITE SYMBOL GPR 0 0 0 0 0 0 This register can be used as a way of storing and retrieving non-volatile information in the EEPROM to be used by the software driver. The storage is word oriented, and the EEPROM word address to be read or written is specified using the six lowest bits of the Pointer Register. This register can also be used to sequentially program the Individual Address area of the EEPROM, that is normally protected from accidental Store operations. This register will be used for EEPROM read and write only when the EEPROM SELECT bit in the Control Register is set. This allows generic EEPROM read and write routines that do not affect the basic setup of the LAN91C93I. SMSC DS - LAN91C93I Page 39 DATASHEET Rev. 09/30/2002 Non-PCI Single-Chip Full Duplex Ethernet Controller I/O SPACE - BANK1 OFFSET C 0 0 LE ENABLE 0 NAME CONTROL REGISTER RCV_ BAD 0 CR ENABLE 0 TYPE READ/WRITE PWRDN RSRVD 0 TE ENABLE 0 0 AUTO RELEASE 0 X X SYMBOL CTR 1 X EEPROM SELECT 0 X RELOAD 1 STORE 0 0 RCV_BAD - When set, bad CRC packets are received. When clear bad CRC packets do not generate interrupts and their memory is released. PWRDN - Active high bit used to put the Ethernet function in power down mode. Cleared by: 1. A write to any register in the LAN91C93I I/O space. 2. Hardware reset. This bit is the powerdown bit to determine when the function is powered down. AUTO RELEASE - When set, transmit pages are released by transmit completion if the transmission was successful (when TX_SUC is set). In that case there is no status word associated with its packet number, and successful packet numbers are not even written into the TX COMPLETION FIFO. A sequence of transmit packets will only generate an interrupt when the sequence is completely transmitted (TX EMPTY INT will be set), or when a packet in the sequence experiences a fatal error (TX INT will be set). Upon a fatal error TXENA is cleared and the transmission sequence stops. The packet number that failed is the present in the FIFO PORTS register, and its pages are not released, allowing the CPU to restart the sequence after corrective action is taken. LE ENABLE - Link Error Enable. When set it enables the LINK_OK bit transition as one of the interrupts merged into the EPH INT bit. Defaults low (disabled). Writing this bit also serves as the acknowledge by clearing previous LINK interrupt conditions. CR ENABLE - Counter Roll over Enable. When set it enables the CTR_ROL bit as one of the interrupts merged into the EPH INT bit. Defaults low (disabled). TE ENABLE - Transmit Error Enable. When set it enables Transmit Error as one of the interrupts merged into the EPH INT bit. Defaults low (disabled). Transmit Error is any condition that clears TXENA with TX_SUC staying low as described in the EPHSR register. EEPROM SELECT - This bit allows the CPU to specify which registers the EEPROM RELOAD or STORE refers to. When high, the General Purpose Register is the only register read or written. When low, the RELOAD and STORE functions are enabled. RELOAD - The LAN91C93I reads the Configuration, Base and Individual Address, and STORE writes the Configuration and Base registers. Also when set it will read the EEPROM and update relevant registers with its contents. This bit then Clears upon completing the operation. STORE - The STORE LAN91C93I bit when set, stores the contents of all relevant registers in the serial EEPROM. This bit is cleared upon completing the operation. Rev. 09/30/2002 Page 40 DATASHEET SMSC DS - LAN91C93I Non-PCI Single-Chip Full Duplex Ethernet Controller Note: When an EEPROM access is in progress the STORE and RELOAD bits will be read back as high. The remaining 14 bits of this register will be invalid. During this time, attempted read/write operations, other than polling the EEPROM status, will NOT have any effect on the internal registers. The CPU can resume accesses to the LAN91C93I after both bits are low. A worst case RELOAD operation initiated by RESET or by software takes less than 750usec in either mode. I/O SPACE - BANK2 OFFSET NAME 0 MMU COMMAND REGISTER TYPE WRITE ONLY BUSY bit readable SYMBOL MMUCR This register is used by the CPU to control the memory allocation, de-allocation, TX FIFO and RX FIFO control. The three command bits determine the command issued as described below: COMMAND w x 0 y N2 N1 N0/ BUSY z 0 COMMAND SET: wxyz 0000 0) - NOOP - NO OPERATION 0010 2) - ALLOCATE MEMORY FOR TX - N2, N1, N0 defines the amount of memory requested as (value + 1) 256* bytes. Namely N2, N1, N0 = 1 will request 2 256* = 512 bytes. Valid range for N2, N1, N0 is 0 through 5. A shift-based divide by 256 of the packet length yields the appropriate value to be used as N2, N1 and N0. Immediately generates a completion code at the ALLOCATION RESULT REGISTER. Can optionally generate an interrupt on successful completion. The allocation time can take worst case (N2, N1, N0 + 2)* 200ns. 0100 4) - RESET MMU TO INITIAL STATE - Frees all memory allocations, clears relevant interrupts, resets packet FIFO pointers. 0110 6) - REMOVE FRAME FROM TOP OF RX FIFO - To be issued after CPU has completed processing of present receive frame. This command removes the receive packet number from the RX FIFO and brings the next receive frame (if any) to the RX area (output of RX FIFO). 0111 7) - REMOVE FRAME FROM TOP OF TX FIFO - To be issued ONLY after the Host disabled the transmitter and has completed processing of the present transmit frame. Note: Determining Transmit completion is done by polling the TEMPTY bit in the Transmit FIFO Port Register. This command removes the Transmit packet number from the TX FIFO and brings the next Transmit frame (if any) to the TX area (output of TX FIFO). 1000 8) - REMOVE AND RELEASE TOP OF RX FIFO - Like 6) but also releases all memory used by the packet presently at the RX FIFO output. 1010 A) - RELEASE SPECIFIC PACKET - Frees all pages allocated to the packet specified in the PACKET NUMBER REGISTER. Should not be used for frames pending transmission. Typically used to remove transmitted frames, after reading their completion status. Can be used following 6 (to release receive packet memory in a more flexible way than 8). 1100 C) - ENQUEUE PACKET NUMBER INTO TX FIFO - This is the normal method of transmitting a packet just loaded into RAM. The packet number to be enqueued is taken from the PACKET NUMBER REGISTER. SMSC DS - LAN91C93I Page 41 DATASHEET Rev. 09/30/2002 Non-PCI Single-Chip Full Duplex Ethernet Controller 1110 F) - RESET TX FIFOs - This command will reset both TX FIFOs. The TX FIFO holding the packet numbers awaiting transmission and the TX Completion FIFO. This command provides a mechanism for canceling packet transmissions, and reordering or bypassing the transmit queue. The RESET TX FIFOs command should only be used when the transmitter is disabled. Unlike the RESET MMU command, the RESET TX FIFOs does not release any memory. Notes: Only command 2 uses N2, N1 and N0. When using the RESET TX FIFOS command, the CPU is responsible for releasing the memory associated with outstanding packets, or re-enqueuing them. Packet numbers in the completion FIFO can be read via the FIFO ports register before issuing the command. MMU commands releasing memory (commands 8 and A) should only be issued if the corresponding packet number has memory allocated to it. COMMAND SEQUENCING A second allocate command (command 2) should not be issued until the present one has completed. Completion is determined by reading the FAILED bit of the allocation result register or through the allocation interrupt. A second release command (commands 8 and A) should not be issued if the previous one is still being processed. The BUSY bit indicates that a release command is in progress. After issuing command A, the contents of the PNR should not be changed until BUSY goes low. After issuing command 8, command 6 should not be issued until BUSY goes low. BUSY BIT - Readable at bit "0" of the MMU command register address. When set indicates that MMU is still processing a release command. When clear, MMU has already completed last release command. BUSY and FAILED bits are set upon the trailing edge of command. I/O SPACE - BANK2 OFFSET 1 D7 0 NAME AUTO TX START REGISTER D6 0 D5 0 D4 0 D3 0 TYPE READ/WRITE D2 0 SYMBOL AUTOTX D1 0 D0 0 AUTO TX START REGISTER This register specifies the value, in 16 byte multiples of when the transmit state machine starts a transmit operation when the associated transmit buffer is enqueued into the transmit FIFO. The AutoTx bit as well as the ETEN bit must both be set in the pointer register in order for this register to be utilized. Note: This register must be non-zero for the Auto-Tx function to work. A value of "0" will disable this function. The RCV bit in the Pointer register must be zero (0) as well. The RCV bit must be cleared so that the packet being written and enqueued is being selected by the PNR and not the receive FIFO. Register Operation: When Early Transmit is enabled via the ETEN bit in the pointer register, the host is able to enqueue a buffer for transmit operation before all of the transmitted data is copied into the LAN91C93I dual ported RAM. In the case of the AutoTx bit being cleared, the host must manually start the transmit operation. When the AutoTx bit is set, the EPH Transmit engine compares the number of bytes moved into the transmit packet buffer with the value of the Auto TX Start Register to start transmit operation. This eliminates the requirement for the host to manually start the transmit. Rev. 09/30/2002 Page 42 DATASHEET SMSC DS - LAN91C93I Non-PCI Single-Chip Full Duplex Ethernet Controller I/O SPACE - BANK2 OFFSET 2 NAME PACKET NUMBER REGISTER RESERVED 0 0 0 TYPE READ/WRITE SYMBOL PNR PACKET NUMBER AT TX AREA 0 0 0 0 0 PACKET NUMBER AT TX AREA - The value written into this register determines which packet number is accessible through the TX area. Some MMU commands use the number stored in this register as the packet number parameter. This register is cleared by a RESET or a RESET MMU Command. RESERVED - This bit is reserved. I/O SPACE - BANK2 OFFSET 3 NAME ALLOCATION RESULT REGISTER TYPE READ ONLY SYMBOL ARR This register is updated upon an ALLOCATE MEMORY MMU command. FAILED 1 0 0 0 ALLOCATED PACKET NUMBER 0 0 0 0 FAILED - A "0" indicates a successful allocation completion. If the allocation fails the bit is set and only cleared when the pending allocation is satisfied. Defaults high upon reset and reset MMU command. For polling purposes, the ALLOC_INT in the Interrupt Status Register should be used because it is synchronized to the read operation. Sequence: 1. Allocate Command 2. Poll ALLOC_INT bit until set 3. Read Allocation Result Register ALLOCATED PACKET NUMBER - Packet number associated with the last memory allocation request. The value is only valid if the FAILED bit is clear. Note: For software compatibility with future versions, the value read from the ARR after an allocation request is intended to be written into the PNR as is, without masking higher bits (provided FAILED = "0"). SMSC DS - LAN91C93I Page 43 DATASHEET Rev. 09/30/2002 Non-PCI Single-Chip Full Duplex Ethernet Controller I/O SPACE - BANK2 OFFSET 4 NAME FIFO PORTS REGISTER TYPE READ ONLY SYMBOL FIFO This register provides access to the read ports of the Receive FIFO and the Transmit completion FIFO. The packet numbers to be processed by the interrupt service routines are read from this register. REMPTY 1 0 0 0 RX FIFO PACKET NUMBER 0 0 0 0 TEMPTY 1 0 0 0 TX FIFO/ PACKET NUMBER 0 0 0 0 REMPTY - No receive packets queued in the RX FIFO. For polling purposes, uses the RCV_INT bit in the Interrupt Status Register. TOP OF RX FIFO PACKET NUMBER - Packet number presently at the output of the RX FIFO. Only valid if REMPTY is clear. The packet is removed from the RX FIFO using MMU Commands 6) or 8). TEMPTY - No transmit packets in completion queue. For polling purposes, uses the TX_INT bit in the Interrupt Status Register. TX PACKET NUMBER - Packet number presently at the output of the TX FIFO. Only valid if TEMPTY is clear. The packet is removed when a TX INT acknowledge is issued. Note: For software compatibility with future versions, the value read from each FIFO register is intended to be written into the PNR as is, without masking higher bits (provided TEMPTY and REMPTY = 0 respectively). I/O SPACE - BANK2 OFFSET 6 NAME POINTER REGISTER RCV AUTO INCR. READ 0 0 0 0 0 0 ETEN TYPE READ/WRITE AutoTx 0 0 POINTER LOW 0 0 SYMBOL PTR POINTER HIGH 0 0 0 0 0 0 POINTER REGISTER - The value of this register determines the address to be accessed within the transmit or receive areas. It will auto-increment on accesses to the data register when AUTO INCR. is set. The increment is by one for every byte access, and by two for every word access. When RCV is set the address refers to the receive area and uses the output of RX FIFO as the packet number, when RCV is clear the address refers to the transmit area and uses the packet number at the Packet Number Register. READ bit - Determines the type of access to follow. If the READ bit is high the operation intended is a read. If the READ bit is low the operation is a write. Loading a new pointer value, with the READ bit high, generates a pre-fetch into the Data Register for read purposes. Read-back of the pointer will indicate the value of the address last accessed by the CPU (rather than the last pre-fetched). This allows any interrupt routine that uses the pointer, to save it and restore it without affecting the process being interrupted. Rev. 09/30/2002 Page 44 DATASHEET SMSC DS - LAN91C93I Non-PCI Single-Chip Full Duplex Ethernet Controller The Pointer Register should not be loaded until 400ns after the last write operation to the Data Register to ensure that the Data Register FIFO is empty. On reads, if IOCHRDY is not connected to the host, the Data Register should not be read before 400ns after the pointer was loaded to allow the Data Register FIFO to fill. If the pointer is loaded using 8 bit writes, the low byte should be loaded first and the high byte last. ETEN bit - When set enables EARLY Transmit underrun detection. Normal operation when clear. If TCR bit 14 (ETEN-TYPE) is zero and this bit is set, the Early transmit underrun function will be enabled as it was implemented in the LAN91C94: "The Early Transmit function allows the CPU to enqueue the first transmit packet before it is fully loaded in packet memory. The loading operation proceeds in parallel with the transmission, and in the case that the transmitter gets ahead of the CPU, the LAN91C94 will prevent the transmission of erroneous data by forcing an Underrun condition. Underruns will be triggered by starving the transmit DMA if the LAN91C93I detects that the DMA TX address exceeds the pointer address." If TCR bit 14 (ETEN-TYPE) is zero and this bit is set, the Early transmit underrun function defined as follows: "For underrun detection purposes the RAM logical address and packet numbers of the packet being loaded are compared against the logical address and packet numbers of the packet being transmitted. If the packet numbers match and the logical address of the packet being transmitted exceeds the address being loaded the LAN91C93I will prevent the transmission of erroneous data by forcing an Underrun condition. Underruns will be triggered by starving the transmit DMA if the LAN91C93I detects that the DMA TX address exceeds the pointer address." Note: In the absence of ETEN-TYPE in TCR, ETEN will have the definition as ETEN-TYPE were clear only. AutoTx bit - When set, enables the transmit state machine to Automatically start a transmit operation with no host intervention determined by the number of bytes being copied into the transmit buffer enqueued in the transmit FIFO. The ETEN bit must also be set in order for this function to be enabled and the RCV bit must be cleared (0). When the Auto TX bit is cleared, the transmit state machine must manually be enabled to enqueue a transmit buffer. If AUTO INCR. is not set, the pointer must be loaded with an even value. I/O SPACE - BANK2 OFFSET 8&A NAME DATA REGISTER TYPE READ/WRITE SYMBOL DATA DATA HIGH DATA LOW DATA REGISTER - Used to read or write the data buffer byte/word presently addressed by the pointer register. This register is mapped into two uni-directional FIFOs that allow moving words to and from the LAN91C93I regardless of whether the pointer address is even or odd. Data goes through the write FIFO into memory, and is pre-fetched from memory into the read FIFO. If byte accesses are used, the appropriate (next) byte SMSC DS - LAN91C93I Page 45 DATASHEET Rev. 09/30/2002 Non-PCI Single-Chip Full Duplex Ethernet Controller can be accessed through the Data Low or Data High registers. The order to and from the FIFO is preserved. Byte and word accesses can be mixed on the fly in any order. This register is mapped into two consecutive word locations to facilitate the usage of double word move instructions. The DATA register is accessible at any address in the 8 through Ah range, while the number of bytes being transferred are determined by A0 and nSBHE in LOCAL BUS mode. I/O SPACE - BANK2 OFFSET C TX IDLE INT 0 NAME INTERRUPT STATUS REGISTER ERCV INT 0 OFFSET EPH INT 0 OFFSET D 0 ALLOC INT TX EMPTY INT 0 0 1 RX_ OVRN INT ERCV INT TX IDLE INT MASK RX_ OVRN INT NAME INTERRUPT ACKNOWLEDGE REGISTER C EPH INT MASK 0 TX INT 0 SYMBOL IST RCV INT 0 TYPE SYMBOL WRITE ONLY ACK TX EMPTY INT NAME INTERRUPT MASK REGISTER ERCV INT MASK 0 TYPE READ ONLY TX INT TYPE READ/WRITE RX_ OVRN INT MASK ALLOC INT MASK TX EMPTY INT MASK 0 0 0 TX INT MASK 0 SYMBOL MSK RCV INT MASK 0 This register can be read and written as a word or as two individual bytes. The Interrupt Mask Register bits enable the appropriate bits when high and disable them when low. A MASK bit being set will cause a hardware interrupt. TX IDLE INT - Transmit Idle interrupt. Set when the transmit state machine is not active. This bit is used under the condition where the TX FIFO is still NOT empty, the transmitter is disabled and the host wants to determine when the transmitter is completed with the current transmit packet. This event usually happens when the host wants to insert at the head of the transmit queue a frame for example. Typical flow of events/Condition: 1. The transmit FIFO is not empty 2. The transmit DONE FIFO is either empty or not empty 3. The transmit engine is either active or not active Rev. 09/30/2002 Page 46 DATASHEET SMSC DS - LAN91C93I Non-PCI Single-Chip Full Duplex Ethernet Controller Flow of events for an insertion of a transmit packet: 1. Disable the Transmitter 2. Remove and release any "transmit done" packets in the TX FIFO 3. Via polling or an interrupt driven event, determine status of TX IDLE INT bit and wait until this bit is set. This will determine when the transmitter is truly done with all transmit events. 4. Remove and store (if any, in software) Packet numbers from the transmit FIFO. (These packets will later be restored into the TX FIFO after the control frame is inserted into the front of the TX FIFO). 5. Enable Transmitter 6. En-queue packet into TX FIFO 7. En-queue rest of packets, if any, into TX FIFO (restore TX FIFO) ERCV INT - Early receive interrupt. Set whenever a receive packet is being received, and the number of bytes received into memory exceeds the value programmed as ERCV THRESHOLD (Bank 3, Offset Ch). ERCV INT stays set until acknowledged by writing the INTERRUPT ACKNOWLEDGE REGISTER with the ERCV INT bit set. EPH INT - Set when the Ethernet Protocol Handler section indicates one out of various possible special conditions. This bit merges exception type of interrupt sources, whose service time is not critical to the execution speed of the low level drivers. The exact nature of the interrupt can be obtained from the EPH Status Register (EPHSR), and enabling of these sources can be done via the Control Register. The possible sources are: 1. LINK - Link Test transition 2. CTR_ROL - Statistics counter roll over 3. TXENA cleared - A fatal transmit error occurred forcing TXENA to be cleared. TX_SUC will be low and the specific reason will be reflected by the bits: 3.1 TXUNRN - Transmit under-run 3.2 SQET - SQE Error 3.3 LOST CARR - Lost Carrier 3.4 LATCOL - Late Collision 3.5 16COL - 16 collisions Any of the above interrupt sources can be masked by the appropriate ENABLE bits in the Control Register. 1) LE ENABLE (Link Error Enable), 2) CR ENABLE (Counter Roll Over), 3) TE ENABLE (Transmit Error Enable) EPH INT will only be cleared by the following methods: 1. Clearing the LE ENABLE bit in the Control Register if an EPH interrupt is caused by a LINK_OK transition. 2. Reading the Counter Register if an EPH interrupt is caused by statistics counter roll over. SMSC DS - LAN91C93I Page 47 DATASHEET Rev. 09/30/2002 Non-PCI Single-Chip Full Duplex Ethernet Controller 3. Setting TXENA bit high if an EPH interrupt is caused by any of the fatal transmit error listed above (3.1 to 3.5). RX_OVRN INT - Set when 1) the receiver aborts due to an overrun due to a failed memory allocation, 2) the receiver aborts due to a packet length of greater than 2K bytes, or 3) the receiver aborts due to the RCV DISCRD bit in the ERCV register set. The RX_OVRN INT bit latches the condition for the purpose of being polled or generating an interrupt, and will only be cleared by writing the acknowledge register with the RX_OVRN INT bit set. ALLOC INT - Set when an MMU request for TX ram pages is successful. This bit is the complement of the FAILED bit in the ALLOCATION RESULT register. The ALLOC INT bit is cleared by the MMU when the next allocation request is processed or allocation fails. TX EMPTY INT - Set if the TX FIFO goes empty, can be used to generate a single interrupt at the end of a sequence of packets enqueued for transmission. This bit latches the empty condition, and the bit will stay set until it is specifically cleared by writing the acknowledge register with the TX EMPTY INT bit set. If a real time reading of the FIFO empty is desired, the bit should be first cleared and then read. The TX_EMPTY MASK bit should only be set after the following steps: a) A packet is enqueued for transmission b) The previous empty condition is cleared (acknowledged) TX INT - Set when at least one packet transmission was completed or any of the below transmit fatal errors occurs: 1. TXUNRN - Transmit under-run 2. SQET - SQE Error 3. LOST CARR - Lost Carrier 4. LATCOL - Late Collision 5. 16COL - 16 collisions The first packet number to be serviced can be read from the FIFO PORTS register. The TX INT bit is always the logic complement of the TEMPTY bit in the FIFO PORTS register. After servicing a packet number, its TX INT interrupt is removed by writing the Interrupt Acknowledge Register with the TX INT bit set. RCV INT - Set when a receive interrupt is generated. The first packet number to be serviced can be read from the FIFO PORTS register. The RCV INT bit is always the logic complement of the REMPTY bit in the FIFO PORTS register. Receive Interrupt is cleared when RX FIFO is empty. Note: For edge triggered systems, the Interrupt Service Routine should clear the Interrupt Mask Register, and only enable the appropriate interrupts after the interrupt source is serviced (acknowledged). Rev. 09/30/2002 Page 48 DATASHEET SMSC DS - LAN91C93I Page 49 DATASHEET MERGED INTO EPH INT EPHSR INTERRUPTS TX_SVC TXENA TEMASK CRMASK CTR-ROL LEMASK EDGE DETECTOR ON LINK ERR TX Complete nWRACK Fatal Transmit Error IntAck6 IntAck4 IntAck2 IntAck1 nQ Q Q nQ Q nQ TX State Machine is not Active D Q nQ ERCV D RX_OVRN ALLOCATION FAILED D S TX FIFO EMPTY D S S SMSC DS - LAN91C93I S TXUNRN SQET LOST CARR LATCOL 16COL nRDIST OE 7 5 DATA BUS 6 4 3 2 16 D0-7 REGISTER STATUS INTERRUPT 1 0 7 6 5 3 2 1 D8-15 REGISTER INTERRUPT MASK 4 RCV FIFO NOT EMPTY 0 nOE MAIN INTERRUPTS TXIDLEINT ERCV INT EPH INT RX_OVRN INT ALLOC INT TX EMPTY INT TX INT RCV INT INT Non-PCI Single-Chip Full Duplex Ethernet Controller Figure 7.2 - Interrupt Structure Rev. 09/30/2002 Non-PCI Single-Chip Full Duplex Ethernet Controller I/O SPACE - BANK 3 OFFSET 0 THROUGH 7 NAME MULTICAST TABLE 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 TYPE READ/WRITE Multicast Table 0 0 0 Multicast Table 1 0 0 Multicast Table 2 0 0 Multicast Table 3 0 0 Multicast Table 4 0 0 Multicast Table 5 0 0 Multicast Table 6 0 0 Multicast Table 7 0 0 SYMBOL MT 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 The 64 bit multicast table is used for group address filtering. The hash value is defined as the six most significant bits of the CRC of the destination addresses. The three msb's determine the register to be used (MT0-7), while the other three determine the bit within the register. If the appropriate bit in the table is set, the packet is received. If the ALMUL bit in the RCR register is set, all multicast addresses are received regardless of the multicast table values. Hashing is for a partial group address filtering scheme. Additional filtering is done in software. But the hash value being a part of the receive status word, the receive routine can reduce the search time significantly. With the proper memory structure, the search is limited to comparing only the multicast addresses that have the actual hash value in question. I/O SPACE - BANK3 OFFSET 8 NAME MANAGEMENT INTERFACE TYPE READ/WRITE SYMBOL MGMT This register contains status bits and control bits for management of different transceivers modules. Some of the pins are shared with the serial EEPROM interface. Management is software controlled, and does not use the serial EEPROM and the transceiver management functions at the same time. 0 0 1 1 0 0 1 1 MDOE 0 IOS2 IOS1 IOS0 MCLK 0 MDI 0 MD0 0 IOS0-2 - Read only bits reflecting the status of the IOS0-2 pins. MDO - The value of this bit drives the EEDO pin when MDOE=1. MDCLK - The value of this bit drives the EESK pin when MDOE=1. Rev. 09/30/2002 Page 50 DATASHEET SMSC DS - LAN91C93I Non-PCI Single-Chip Full Duplex Ethernet Controller MDOE - When this bit is high pins EEDO EECS and EESK will be used for transceiver management functions, otherwise the pins assume the EEPROM values. MODE=0 Serial EEPROM Data Out Serial EEPROM Clock Serial EEPROM Chip Select EEDO EESK EECS MODE=1 Bit MDO Bit MCLK 0 I/O SPACE - BANK3 OFFSET A 0 NAME REVISION REGISTER 0 1 TYPE READ ONLY 1 0 0 CHIP 0 0 SYMBOL REV 1 1 0 0 REV 1 0 CHIP ID VALUE 2 3 4 5 4* 7 8 9 0 0 DEVICE LAN91C93I LAN91C90/LAN91C92 LAN91C94 LAN91C95 LAN91C96 LAN91C100 LAN91C100FD LAN91C110 CHIP - Chip ID. Can be used by software drivers to identify the device used. REV - Revision ID. Incremented for each revision of a given device. Note: The LAN91C96 shares the same chip ID (#4) as the LAN91C94. The Rev. ID for the LAN91C96 will begin from six (#6). I/O SPACE - BANK3 OFFSET C 0 RCV DISCRD 0 NAME EARLY RCV REGISTER 0 1 0 0 TYPE READ/WRITE RCV COUNTER 1 0 0 1 ERCV THRESHOLD 1 1 1 1 SYMBOL ERCV 1 1 RCV DISCRD - Set to discard a packet being received. SMSC DS - LAN91C93I Page 51 DATASHEET Rev. 09/30/2002 Non-PCI Single-Chip Full Duplex Ethernet Controller ERCV THRESHOLD - Threshold for ERCV interrupt. Specified in 64 byte multiples. Whenever the number of bytes written in memory for the presently received packet exceeds the ERCV THRESHOLD, ERCV INT bit of the INTERRUPT STATUS REGISTER is set. Rcv Counter - This 8 bit value is the "Real Time" count, in bytes, of the current Receive packet (this includes the 4 bytes of status and packet length). The count is rounded to the nearest Nibble (16 bytes). The Counter is multiplied by 16 decimals to obtain the number of bytes currently received. Notes: The value of the RCV Counter is in real time asynchronous format (i.e. The value is constantly changing). It is recommended that the register be read multiple times to get an accurate reading. The Rcv Counter register will return a value of "0" when no receive event is occurring. Rev. 09/30/2002 Page 52 DATASHEET SMSC DS - LAN91C93I Non-PCI Single-Chip Full Duplex Ethernet Controller Chapter 8 Theory of Operation The concept of presenting the shared RAM as a FIFO of packets, with a memory management unit allocating memory on a per packet basis responds to the following needs: Memory allocation for receive vs. transmit - A fixed partition between receive and transmit area would not be efficient. Being able to dynamically allocate it to transmit and receive represents almost the equivalent of duplicating the memory size for some workstation type of drivers. Software overhead - By presenting a FIFO of packets, the software driver does not have to waste any time in calculating pointers for the different buffers that make up different packets. The driver usually deals with one packet at a time. With this approach, packets are accessible always at the same fixed address, and access is provided to any byte of the packet. Headers can be analyzed without reading out the entire packet. The packet can be moved in or out with a block move operation. Multiple upper layer support - The LAN91C93I facilitates interfacing to multiple upper layer protocols because of the receive packet processing flexibility. A receive lookahead scheme like ODI or NDIS drivers is supported by copying a small part of the received packet and letting the upper layer provide a pointer for the rest of the data. If the upper layer indicates it does not want the packet, it can be removed upon a single command. If the upper layer wants a specific part of the packet, a block move operation starting at any particular offset can be done. Out of order receive processing is also supported: if memory for one packet is not yet available, receive packet processing can continue. Efficiency - Lacking any level of indirection or linked lists of pointers, virtually all the memory is used for data. There are no descriptors, forward links and pointers at all. This simplicity and memory efficiency is accomplished without giving up the benefits of linked lists which is unlimited back-to-back transmission and reception without CPU intervention for as long as memory is available. 8.1 Full Duplex Support Full Duplex Ethernet operation refers to the ability of the network (or parts of it) to simultaneously transmit and receive packets. The CSMA/CD protocol used by Ethernet for accessing a shared medium is inherently half duplex, and so is the 10BASE-T physical layer where simultaneous transmit and receive activity is interpreted as a collision. The LAN91C93I supports two types of Full Duplex operation: Note: 1. Full Duplex mode for diagnostic purposes only, where the received packet is the transmit packet being looped back. This mode is enabled using the FDUPLX bit in the TCR. In this mode the CSMA/CD algorithm is used to gain access to the media. 2. FDSE (Full Duplex Switched Ethernet). Enabled by FDSE bit in TCR bit. When the LAN91C93I is configured for FDSE, its transmit and receive paths will operate independently with Carrier Sense CSMA/CD function disabled. In FDSE mode the packets are not looped back internally. The loopback (Full Duplex for Diagnostics(FDUPLX)) function of 10BASE-T transceivers is permanently engaged. It presents the transmit pair waveform to the receive circuit internally. This function allows the receiver to see the controller's own transmission, not only to permit diagnostics, but also to ensure sure that the node defers to its own transmission - as specified in 802.3. SMSC DS - LAN91C93I Page 53 DATASHEET Rev. 09/30/2002 Non-PCI Single-Chip Full Duplex Ethernet Controller Behavior in FDSE mode A) No deferral - The transmit channel is dedicated and always available - The device transmits whenever it has a packet ready to be sent, while respecting the interframe spacing between transmit packets. B) No collision detection - There are no collisions in a switched full duplex environment. 8.2 Typical Flow of Events for Transmit (Auto Release = 0) MAC SIDE S/W DRIVER 1 2 3 4 ISSUE ALLOCATE MEMORY FOR TX - N BYTES - the MMU attempts to allocate N bytes of RAM. WAIT FOR SUCCESSFUL COMPLETION CODE - Poll until the ALLOC INT bit is set or enable its mask bit and wait for the interrupt. The TX packet number is now at the Allocation Result Register. LOAD TRANSMIT DATA - Copy the TX packet number into the Packet Number Register. Write the Pointer Register, then use a block move operation from the upper layer transmit queue into the Data Register. ISSUE "ENQUEUE PACKET NUMBER TO TX FIFO" - This command writes the number present in the Packet Number Register into the TX FIFO. The transmission is now enqueued. No further CPU intervention is needed until a transmit interrupt is generated. 5 6 Rev. 09/30/2002 The enqueued packet will be transferred to the MAC block as a function of TXENA (nTCR) bit and of the deferral process (1/2 duplex mode only) state. a) Upon transmit completion the first word in memory is written with the status word. The packet number is moved from the TX FIFO into the TX completion FIFO. Interrupt is generated by the TX completion FIFO being not empty. b) If a TX failure occurs on any packets, TX INT is generated and TXENA is cleared, transmission sequence stops. The packet number of the failure packet is presented at the TX FIFO PORTS Register. Page 54 DATASHEET SMSC DS - LAN91C93I Non-PCI Single-Chip Full Duplex Ethernet Controller 7 a) SERVICE INTERRUPT - Read Interrupt Status Register. If it is a transmit interrupt, read the TX FIFO Packet Number from the FIFO Ports Register. Write the packet number into the Packet Number Register. The corresponding status word is now readable from memory. If status word shows successful transmission, issue RELEASE packet number command to free up the memory used by this packet. Remove packet number from completion FIFO by writing TX INT Acknowledge Register. b) Option 1) Release the packet. Option 2) Check the transmit status in the EPH STATUS Register, write the packet number of the current packet to the Packet Number Register, re-enable TXENA, then go to step 4 to start the TX sequence again. SMSC DS - LAN91C93I Page 55 DATASHEET Rev. 09/30/2002 Non-PCI Single-Chip Full Duplex Ethernet Controller 8.3 Typical Flow of Events for Transmit (Auto Release = 1) MAC SIDE S/W DRIVER 1 2 3 4 ISSUE ALLOCATE MEMORY FOR TX - N BYTES - the MMU attempts to allocate N bytes of RAM. WAIT FOR SUCCESSFUL COMPLETION CODE - Poll until the ALLOC INT bit is set or enable its mask bit and wait for the interrupt. The TX packet number is now at the Allocation Result Register. LOAD TRANSMIT DATA - Copy the TX packet number into the Packet Number Register. Write the Pointer Register, then use a block move operation from the upper layer transmit queue into the Data Register. ISSUE "ENQUEUE PACKET NUMBER TO TX FIFO" - This command writes the number present in the Packet Number Register into the TX FIFO. The transmission is now enqueued. No further CPU intervention is needed until a transmit interrupt is generated. 5 The enqueued packet will be transferred to the MAC block as a function of TXENA (nTCR) bit and of the deferral process (1/2 duplex mode only) state. Transmit pages are released by transmit completion. a) The MAC generates a TXEMPTY interrupt upon a completion of a sequence of enqueued packets. b) If a TX failure occurs on any packets, TX INT is generated and TXENA is cleared, transmission sequence stops. The packet number of the failure packet is presented at the TX FIFO PORTS Register. 6 7 8 a) SERVICE INTERRUPT - Read Interrupt Status Register, exit the interrupt service routine. b) Option 1) Release the packet. Option 2) Check the transmit status in the EPH STATUS Register, write the packet number of the current packet to the Packet Number Register, re-enable TXENA, then go to step 4 to start the TX sequence again. Rev. 09/30/2002 Page 56 DATASHEET SMSC DS - LAN91C93I Non-PCI Single-Chip Full Duplex Ethernet Controller 8.4 Typical Flow of Events for Receive CSMA/CD SIDE S/W DRIVER 1 ENABLE RECEPTION - By setting the RXEN bit. 2 A packet is received with matching address. Memory is requested from MMU. A packet number is assigned to it. Additional memory is requested if more pages are needed. The internal DMA logic generates sequential addresses and writes the receive words into memory. The MMU does the sequential to physical address translation. If overrun, packet is dropped and memory is released. When the end of packet is detected, the status word is placed at the beginning of the receive packet in memory. Byte count is placed at the second word. If the CRC checks correctly the packet number is written into the RX FIFO. The RX FIFO being not empty causes RCV INT (interrupt) to be set. If CRC is incorrect the packet memory is released and no interrupt will occur. 3 4 5 SERVICE INTERRUPT - Read the Interrupt Status Register and determine if RCV INT is set. The next receive packet is at receive area. (Its packet number can be read from the FIFO Ports Register). The software driver can process the packet by accessing the RX area, and can move it out to system memory if desired. When processing is complete the CPU issues the REMOVE AND RELEASE FROM TOP OF RX command to have the MMU free up the used memory and packet number. SMSC DS - LAN91C93I Page 57 DATASHEET Rev. 09/30/2002 Non-PCI Single-Chip Full Duplex Ethernet Controller ISR Save Bank Selec & Address Ptr Registerst Mask Interrupts Read Interrupt Register No Yes TX INTR? Call TX INTR or TXEMPTY INTR RX INTR? Yes No Call RXINTR Get Next TX No Yes No Packet Available for Transmission? ALLOC INTR? Yes Write Allocated Pkt# into Packet Number Reg. Call ALLOCATE Write Ad Ptr Reg. & CopyData & Source Address Yes Call EPH INTR No EPH INTR? Enqueue Packet Set "Ready for Packet" Flag Restore Address Pointer & Bank Select Registers Return Buffers to Upper Layer Unmask Interrupts Disable Allocation Interrupt Mask Exit ISR Figure 8.1 - Interrupt Service Routine Rev. 09/30/2002 Page 58 DATASHEET SMSC DS - LAN91C93I Non-PCI Single-Chip Full Duplex Ethernet Controller RX INTR Write Ad. Ptr. Reg. & Read Word 0 from RAM Yes Destination Multicast? No Read Words 2, 3, 4 from RAM for Address Filtering No Address Filtering Pass? Yes No Status Word OK? Yes Do Receive Lookahead Get Copy Specs from Upper Layer No Okay to Copy? Yes Copy Data Per Upper Layer Specs Issue "Remove and Release" Command Return to ISR Figure 8.2 - RX INTR SMSC DS - LAN91C93I Page 59 DATASHEET Rev. 09/30/2002 Non-PCI Single-Chip Full Duplex Ethernet Controller TX Interrupt With AUTO_RELEASE = FALSE 1. Save the Packet Number Register Saved_PNR = Read Byte (Bank 2, Offset 2) 2. Read the EPH Status Register Temp = Read (Bank 0, Offset 2) 3. Acknowledge TX Interrupt Write Byte (0x02, (Bank 2, Offset C)); 4. Check for Status of Transmission If ( Temp AND 0x0001) { //If Successful Transmission Step 4.1.1: Issue MMU Release (Release Specific Packet) Write (0x00A0, (Bank2, Offset 0)); Step 4.1.2: Return from the routine } else { //Transmission has FAILED // Now we can either release or re-enqueue the packet Step 4.2.1: Get the packet to release/re-enqueue, stored in FIFO Temp = Read (Bank 2, Offset 4) Temp = Temp & 0x003F Step 4.2.2: Write to the PNR Write (Temp, (Bank2, Offset 2)) Step 4.2.3 // Option 1: Release the packet Write (0x00A0, (Bank2, Offset 0)); //Option 2: Re-Enqueue the packet Write (0x00C0, (Bank2, Offset 0)); Step 4.2.4: Re-Enable Transmission Temp = Read(Bank0, Offset 0); Temp = Temp2 OR 0x0001 Write (Temp2, (Bank 0, Offset 0)); Step 4.2.5: Return from the routine } 5. Restore the Packet Number Register Write Byte (Saved_PNR, (Bank 2, Offset 2)) Figure 8.3 - TX INTR Rev. 09/30/2002 Page 60 DATASHEET SMSC DS - LAN91C93I Non-PCI Single-Chip Full Duplex Ethernet Controller TXEMPTY INTR Write Acknowledge Reg. with TXEMPTY Bit Set Read TXEMPTY & TX INTR TXEMPTY = 0 & TXINT = 0 (Waiting for Completion) TXEMPTY = X & TXINT = 1 (Transmission Failed) TXEMPTY = 1 & TXINT = 0 (Everything went through successfully) Read Pkt. # Register & Save Write Address Pointer Register Read Status Word from RAM Update Statistics Issue "Release" Command Update Variables Acknowledge TXINTR Re-Enable TXENA Restore Packet Number Return to ISR Figure 8.4 - TXEMPTY INTR (Assumes Auto Release Option Selected) SMSC DS - LAN91C93I Page 61 DATASHEET Rev. 09/30/2002 Non-PCI Single-Chip Full Duplex Ethernet Controller DRIVER SEND ALLOCATE Choose Bank Select Register 2 Issue "Allocate Memory" Command to MMU Call ALLOCATE Read Interrupt Status Register Exit Driver Send Yes Allocation Passed? No Read Allocation Result Register Write Allocated Packet into Packet # Register Store Data Buffer Pointer Write Address Pointer Register Clear "Ready for Packet" Flag Copy Part of TX Data Packet into RAM Enable Allocation Interrupt Write Source Address into Proper Location Copy Remaining TX Data Packet into RAM Enqueue Packet Set "Ready for Packet" Flag Return Buffers to Upper Layer Return Figure 8.5 - Driver Send and Allocate Routines Rev. 09/30/2002 Page 62 DATASHEET SMSC DS - LAN91C93I Non-PCI Single-Chip Full Duplex Ethernet Controller 8.5 Memory Partitioning Unlike other controllers, the LAN91C93I does not require a fixed memory partitioning between transmit and receive resources. The MMU allocates and de-allocates memory upon different events. An additional mechanism allows the CPU to prevent the receive process from starving the transmit memory allocation. Memory is always requested by the side that needs to write into it, that is: The CPU for transmit or the CSMA/CD for receive. The CPU can control the number of bytes it requests for transmit but it cannot determine the number of bytes the receive process is going to demand. Furthermore, the receive process requests will be dependent on network traffic, in particular on the arrival of broadcast and multicast packets that might not be for the node, and that are not subject to upper layer software flow control. In order to prevent unwanted traffic from using too much memory, the CPU can program a "memory reserved for transmit" parameter. If the free memory falls below the "memory reserved for transmit" value, MMU requests from the CSMA/CD block will fail and the packets will overrun and be ignored. Whenever enough memory is released, packets can be received again. If the reserved value is too large, the node might lose data which is an abnormal condition. If the value is kept at zero, memory allocation is handled on first-come first-served basis for the entire memory capacity. Note that with the memory management built into the LAN91C93I, the CPU can dynamically program this parameter. For instance, when the driver does not need to enqueue transmissions, it can allow more memory to be allocated for receive (by reducing the value of the reserved memory). Whenever the driver needs to burst transmissions it can reduce the receive memory allocation. The driver program the parameter as a function of the following variables: 1. Free memory (read only register) 2. Memory size (read only register) The reserved memory value can be changed on the fly. If the MEMORY RESERVED FOR TX value is increased above the FREE MEMORY, receive packets in progress are still received, but no new packets are accepted until the FREE MEMORY increases above the MEMORY RESERVED value. INTERRUPT GENERATION The interrupt strategy for the transmit and receive processes is such that it does not represent the bottleneck in the transmit and receive queue management between the software driver and the controller. For that purpose there is no register reading necessary before the next element in the queue (namely transmit or receive packet) can be handled by the controller. The transmit and receive results are placed in memory. The receive interrupt will be generated when the receive queue (FIFO of packets) is not empty and receive interrupts are enabled. This allows the interrupt service routine to process many receive packets without exiting, or one at a time if the ISR just returns after processing and removing one. There are two types of transmit interrupt strategies: 1. One interrupt per packet. 2. One interrupt per sequence of packets. The strategy is determined by how the transmit interrupt bits and the AUTO RELEASE bit are used. TX INT bit - Set whenever the TX completion FIFO is not empty. TX EMPTY INT bit - Set whenever the TX FIFO is empty. SMSC DS - LAN91C93I Page 63 DATASHEET Rev. 09/30/2002 Non-PCI Single-Chip Full Duplex Ethernet Controller AUTO RELEASE - When set, successful transmit packets are not written into completion FIFO, and their memory is released automatically. 1. One interrupt per packet: enable TX INT, set AUTO RELEASE=0. The software driver can find the completion result in memory and process the interrupt one packet at a time. Depending on the completion code the driver will take different actions. Note that the transmit process is working in parallel and other transmissions might be taking place. The LAN91C93I is virtually queuing the packet numbers and their status words. In this case, the transmit interrupt service routine can find the next packet number to be serviced by reading the TX PACKET NUMBER at the FIFO PORTS register. This eliminates the need for the driver to keep a list of packet numbers being transmitted. The numbers are queued by the LAN91C93I and provided back to the CPU as their transmission completes. 2. One interrupt per sequence of packets: Enable TX EMPTY INT and TX INT, set AUTO RELEASE=1. TX EMPTY INT is generated only after transmitting the last packet in the FIFO. TX INT will be set on a fatal transmit error allowing the CPU to know that the transmit process has stopped and therefore the FIFO will not be emptied. This mode has the advantage of a smaller CPU overhead, and faster memory de-allocation. Note that when AUTO RELEASE=1 the CPU is not provided with the packet numbers that completed successfully. Note: The pointer register is shared by any process accessing the LAN91C93I memory. In order to allow processes to be interruptible, the interrupting process is responsible for reading the pointer value before modifying it, saving it, and restoring it before returning from the interrupt. Typically there would be three processes using the pointer: 1. Transmit loading (sometimes interrupt driven) 2. Receive unloading (interrupt driven) 3. Transmit Status reading (interrupt driven). 1) and 3) also share the usage of the Packet Number Register. Therefore saving and restoring the PNR is also required from interrupt service routines. POWER DOWN The LAN91C93I can enter power down mode by means of the PWRDN bit (Control Register, bit 13). The power down current is 8 mA. When in power down mode, the LAN91C98 will: Stop the crystal oscillator Tristate: Data Bus Interrupts(only by PWRDN bit) nIOCS16 10BASE-T and AUI outputs Turn off analog bias currents Drive the EEPROM and ROM outputs inactive Rev. 09/30/2002 Page 64 DATASHEET SMSC DS - LAN91C93I Non-PCI Single-Chip Full Duplex Ethernet Controller Preserve contents of registers and memory Powerdown bit is cleared by a write access to any LAN91C93I register or by hardware reset. SMSC DS - LAN91C93I Page 65 DATASHEET Rev. 09/30/2002 Rev. 09/30/2002 OPTIONS TWO INTERRUPT INT ALLOC INT TX TX EMPTY INT INT RCV STATUS REGISTER M.S. BIT ONLY PACKET NUMBER TX DONE TX COMPLETION FIFO 'NOT EMPTY' 'EMPTY' TX FIFO Page 66 DATASHEET PACK # OUT CPU ADDRESS REGISTER PACKET NUMBER PACKET # RAM PHYSICAL ADDRESS MMU LOGICAL ADDRESS RX FIFO NUMBER RX PACKET RX FIFO PACKET NUMBER CSMA ADDRESS 'NOT EMPTY' CSMA/CD Non-PCI Single-Chip Full Duplex Ethernet Controller Figure 8.6 - Interrupt Generation for Transmit; Receive, MMU SMSC DS - LAN91C93I Non-PCI Single-Chip Full Duplex Ethernet Controller Chapter 9 9.1 Functional Description of the Blocks Memory Management Unit The MMU interfaces the on-chip RAM on one side and the arbiter on the other for address and data flow purposes. For allocation and de-allocation, it interfaces the arbiter only. The MMU deals with a single ported memory and is not aware of the fact that there are two entities requesting allocation and actually accessing memory. The mapping function done by the MMU is only a function of the packet number accessed and of the offset within that packet being accessed. It is not a function of who is requesting the access or the direction of the access. To accomplish that, memory accesses as well as MMU allocation and de-allocation requests are arbitrated by the arbiter block before reaching the MMU. Memory allocation could take some time, but the ALLOC INT bit in Interrupt Status Register is negated immediately upon allocation request, allowing the system to poll that register at any time. Memory deallocation command completion indication is provided via the BUSY bit, readable through the MMU command register. The mapping and queuing functions of the MMU rely on the uniqueness of the packet number assigned to the requester. For that purpose the packet number assignment is centralized at the MMU, and a number will not be reused until the memory associated with it is released. It is clear that a packet number should not be released while the number is in the TX or RX packet queue. The TX and RCV FIFOs are deep enough to handle the total number of packets the MMU can allocate, therefore there is no need for the programmer or the hardware to check FIFO full conditions. 9.2 Arbiter The function of the arbiter is to sequence packet RAM accesses as well as MMU requests in such a way that the on-chip single ported RAM and a single MMU can be shared by two parties. One party is the host CPU and the other party is the CSMA/CD block. The arbiter is address transparent, namely, any address can be accessed at any time. In order to exploit the sequential nature of the access, and minimize the access time on the system side, the CPU cycle is buffered by the Data Register rather than go directly to and from memory. Whenever a write cycle is performed, the data is written into the Data Register and will be written into memory as a result of that operation, allowing the CPU cycle to complete before the arbitration and memory cycle are complete. Whenever a read cycle is performed, the data is provided immediately from the Data Register, without having to arbitrate and complete a memory cycle. The present cycle results in an arbitration request for the next data location. Loading the pointer causes a similar pre-fetch request. This type of read-ahead and write-behind arbitration allows the controller to have a very fast access time, and would work without wait states for as long as the cycle time specification is satisfied. The values are 40 ns access time, and 185ns cycle time. By the same token, CSMA/CD cycles might be postponed. The worst case CSMA/CD latency for arbiter service is one memory cycle. The arbiter uses the pointer register as the CPU provided address, and the internal DMA address from the CSMA/CD side as the addresses to be provided to the MMU. SMSC DS - LAN91C93I Page 67 DATASHEET Rev. 09/30/2002 Non-PCI Single-Chip Full Duplex Ethernet Controller The data path routed by the arbiter goes between memory (the data path does not go through the MMU) on one side and either the CPU side bus or the data path of the CSMA/CD core. The data path between memory and the Data Register is in fact buffered by a small FIFO in each direction. The FIFOs beneath the Data Register can be read and written as bytes or words, in any sequential combination. The presence of these FIFOs makes sure that word transfers are possible on the system bus even if the address loaded into the pointer is odd. 9.3 Bus Interface The bus interface handles the data, address and control interfaces and is compliant with the LOCAL BUS. The functions in this block include address decoding for I/O and ROM memory (including address relocation support) for LOCAL BUS, data path routing, sequential memory address support, optional wait state generation, boot ROM support, EEPROM setup function, bus transceiver control, and interrupt generation / selection. For LOCAL BUS, I/O address decoding is done by comparing A15-A4 to the I/O BASE address determined in part by the upper byte of the BASE ADDRESS REGISTER, and also requiring that AEN be low. If the above address comparison is satisfied and the LAN91C93I is in 16 bit mode, nIOCS16 will be asserted (low). A valid comparison does not yet indicate a valid I/O cycle is in progress, as the addresses could be used for a memory cycle, or could even glitch through a valid value. For LOCAL BUS, only when nIORD or nIOWR are activated the I/O cycle begins. 9.4 Wait State Policy The LAN91C93I can work on most system buses without having to add wait states. The two parameters that determine the memory access profile are the read access time and the cycle time into the Data Register. The read access time is 40ns and the cycle time is 185ns. If any one of them does not satisfy the application requirements, wait states should be added. If the access time is the problem, IOCHRDY should be negated for all accesses to the LAN91C93I. This can be achieved by programming the NO WAIT ST bit in the configuration register to "0". The LAN91C93I will negate IOCHRDY for 100ns to 150ns on every access to any register. If the cycle time is the problem, programming NO WAIT ST as described before will solve it but at the expense of slowing down all accesses. The alternative is to let the LAN91C93I negate IOCHRDY only when the Data Register FIFOs require so. Namely, if NO WAIT ST is set, IOCHRDY will only be negated if a Data Register read cycle starts and there is less than a full word in the read FIFO, or if a write cycle starts and there is more than two bytes in the write FIFO. The cycle time is defined as the time between leading edges of read from the Data Register, or equivalently between trailing edges of write to the Data Register. For example, in an LOCAL BUS system the cycle time of a 16 bit transfer will be at least 2 clocks for the I/O access to the LAN91C93I (+ one clock for the memory cycle) for a total of 3 clocks. In absolute time it means 375ns for an 8MHz bus, and 240ns for a 12.5 MHz bus. The cycle time will not increase when configured for full duplex mode, because the CSMA/CD memory arbitration requests are sequenced by the DMA logic and never overlap. Rev. 09/30/2002 Page 68 DATASHEET SMSC DS - LAN91C93I Non-PCI Single-Chip Full Duplex Ethernet Controller 9.5 Arbitration Considerations The arbiter exploits the sequential nature of the CPU accesses to provide a very fast access time. Memory bandwidth considerations will have an effect on the CPU cycle time but no effect on access time. For normal 8MHz, 10MHz, and 12.5MHz LOCAL BUS, as well as EISA normal cycles, the LAN91C93I can be accessed without negating ready. When write operations occur, the data is written into a FIFO. The CPU cycle can complete immediately, and the buffered data will be written into memory later. The memory arbitration request is generated as a function of that FIFO being not empty. The nature of the cycle requested (byte/word) is determined by the LSB of the pointer and the number of bytes in the FIFO. When read operations occur, words are pre-fetched upon pointer loading in order to have at least a word ready in the FIFO to be read. New pre-fetch cycles are requested as a function of the number of bytes in the FIFO. For example, if an odd pointer value is loaded, first a byte is pre-fetched into the FIFO, and immediately a full word is pre-fetched completing three bytes into the FIFO. If the CPU reads a word, one byte will be left again a new word is pre-fetched. In the case of write, if an odd pointer value is loaded, and a full word is written, the FIFO holds two bytes, the first of which is immediately written into an odd memory location. If by that time another byte or word was written, there will be two or three bytes in the FIFO and a full word can be written into the now even memory address. When a CSMA/CD cycle begins, the arbiter will route the CSMA/CD DMA addresses to the MMU as well as the packet number associated with the operation in progress. In full-duplex mode, receive and transmit requests are alternated in such a way that the CPU arbitration cycle time is not affected. 9.6 DMA Block The DMA block resides between the CSMA/CD block and the arbiter. It can interface both the data path and the control path of the CSMA/CD block for different operations. Its functions include the following: Start transmission process into the CSMA/CD block. Generate CSMA/CD side addresses for accessing memory during transmit and receive operations. Generate MMU memory requests and verify success. Compute byte count and write it in first locations of receive packet. Write transmit status word in first locations of transmit packet. Determine if enough memory is available for reception. De-allocate transmit memory after suitable completion. De-allocate receive memory upon error conditions. Initiate retransmissions upon collisions (if less than 16 retries). Terminate reception and release memory if packet is too long. SMSC DS - LAN91C93I Page 69 DATASHEET Rev. 09/30/2002 Non-PCI Single-Chip Full Duplex Ethernet Controller The specific nature of each operation and its trigger event are: 1. TX operations will begin if TXENA is set and TX FIFO is not empty. The DMA logic does not need to use the TX PACKET NUMBER, it goes directly from the FIFO to the MMU. However the DMA logic controls the removal of the PACKET NUMBER from the FIFO. 2. Generation of CSMA/CD side addresses into memory: Independent 11-bit counters are kept for transmit and receive in order to allow full-duplex operation. 3. MMU requests for allocation are generated by the DMA logic upon reception. The initial allocation request is issued when the CSMA block indicates an active reception. If allocation succeeds, the DMA block stores the packet number assigned to it, and generates write arbitration requests for as long as the CSMA/CD FIFO is not empty. In parallel the CSMA/CD completes the address filtering and notifies the DMA of an address match. If there is no address match, the DMA logic will release the allocated memory and stop reception. 4. When the CSMA/CD block notifies the DMA logic that a receive packet was completed, if the CRC is OK, the DMA will either write the previously stored packet number into the RX PACKET NUMBER FIFO (to be processed by the CPU), or if the CRC is bad the DMA will just issue a release command to the MMU (and the CPU will never see that packet). Packets with bad CRC can be received if the RCV_BAD bit in the configuration register is set. 9.7 5. If AUTO_RELEASE is set, a release is issued by the DMA block to the MMU after a successful transmission (TX_SUCC set), and the TX completion FIFO is clocked together with the TX FIFO preventing the packet number from moving into the TX completion FIFO. 6. Based on the RX counter value, if a receive packet exceeds 1532 bytes, reception is stopped by the DMA and the RX ABORT bit in the Receive Control Register is set. The memory allocated to the packet is automatically released. 7. If an allocation fails, the CSMA/CD block will activate RX_OVRN INT upon detecting a FIFO full condition. RXEN will stay active to allow reception of subsequent packets if memory becomes available. The CSMA/CD block will flush the FIFO upon the new frame arrival. Packet Number FIFOs The transmit packet FIFO stores the packet numbers awaiting transmission, in the order they were enqueued. The FIFO is advanced (written) when the CPU issues the "enqueue packet number command", the packet number to be written is provided by the CPU via the Packet Number Register. The number was previously obtained by requesting memory allocation from the MMU. The FIFO is read by the DMA block when the CSMA/CD block is ready to proceed on to the next transmission. By reading the TX EMPTY INT bit the CPU can determine if this FIFO is empty. The transmit completion FIFO stores the packet numbers that were already transmitted but not yet acknowledged by the CPU. The CPU can read the next packet number in this FIFO from the FIFO Ports Register. The CPU can remove a packet number from this FIFO by issuing a TX INT acknowledge. The CPU can determine if this FIFO is empty by reading the TX INT bit or the FIFO Ports Register. The receive packet FIFO stores the packet numbers already received into memory, in the order they were received. The FIFO is advanced (written) by the DMA block upon reception of a complete valid packet into memory. The number is determined the moment the DMA block first requests memory from the MMU for that packet. The first receive packet number in the FIFO can be read via the FIFO Ports Register, and the data associated with it can be accessed through the receive area. The packet number can be removed from the FIFO with or without an automatic release of its associated memory. Rev. 09/30/2002 Page 70 DATASHEET SMSC DS - LAN91C93I Non-PCI Single-Chip Full Duplex Ethernet Controller The FIFO is read out upon CPU command (remove packet from top of RX FIFO, or remove and release command) after processing the receive packet in the receive area. The width of each FIFO is 5 bits per packet number. The depth of each FIFO equals the number of packets the LAN91C93I can handle (18). The guideline is software transparency; the software driver should not be aware of different devices or FIFO depths. If the MMU memory allocation succeeded, there will be room in the transmit FIFO for enqueuing the packet. Conversely if there is free memory for receive, there should be room in the receive FIFO for storing the packet number. Note that the CPU can enqueue a transmit command with a packet number that does not follow the sequence in which the MMU assigned packet numbers. For example, when a transmission failed and it is retried in software, or when a receive packet is modified and sent back to the network. SMSC DS - LAN91C93I Page 71 DATASHEET Rev. 09/30/2002 RAM PACK # OUT ALLOCATION RESULT REGISTER MMU RELEASE REGISTER MMU COMMAND DECODER CPU ADDRESS ALLOCATE LOGICAL ADDRESS TX DONE PACKET NUMBER FIFO INT TX COMPLETION TX FIFO WR REGISTER PACKET NUMBER PACK # OUT PHYSICAL ADDRESS DMA RELEASE PACKET # ALLOCATE CSMA ADDRESS RX PACKET NUMBER RD RX FIFO PACKET NUMBER RX FIFO CSMA/CD Non-PCI Single-Chip Full Duplex Ethernet Controller Figure 9.1 - MMU Packet Number Flow and Relevant Registers 9.8 CSMA Bock The CSMA/CD block is first interfaced via its control registers in order to define its operational configuration. From then on, the DMA interface between the CSMA/CD block and memory is used to transfer data to and from its data path interface. For transmit, the CSMA/CD block will be asked to transmit frames as soon as they are ready in memory. It will continue transmissions until any of the following transmit error occurs: Rev. 09/30/2002 Page 72 DATASHEET SMSC DS - LAN91C93I Non-PCI Single-Chip Full Duplex Ethernet Controller 1. Collisions on same frame 2. Late collision 3. Lost Carrier sense and MON_CSN set 4. Transmit Underrun 5. SQET error and STP_SQET set In that case TXENA will be cleared and the CPU should restart the transmission by setting it again. If a transmission is successful, TXENA stays set and the CSMA/CD is provided by the DMA block with the next packet to be transmitted. For receive, the CPU sets RXEN as a way of starting the CSMA/CD block receive process. The CSMA/CD block will send data after address filtering through the data path to the DMA block. Data is transferred into memory as it is received, and the final check on data acceptance is the CRC checking done by the CSMA/CD block. In any case, the DMA takes care of requesting/releasing memory for receive packets, as well as generating the byte count. The receive status word is provided by the CSMA/CD block and written in the first location of the receive structure by the DMA block. If configured for storing CRC in memory, the CSMA/CD unit will transfer the CRC bytes through the DMA interface, and then will be treated like regular data bytes. Note that the receive status word of any packet is available only through memory and is not readable through any other register. In order to let the CPU know about receive overruns, the RX_OVRN INT is set and latched in the Interrupt Status Register, which is readable by the CPU at any time. The address filtering is done inside the CSMA/CD block. A packet will be received if the destination address is broadcast, or if it is addressed to the individual address of the LAN91C93I, or if it is a multicast address and ALMUL bit is set, or if it is a multicast address matching one of the multicast table entries. If the PRMS bit is set, all packets are received. The CSMA/CD block is a full duplex machine, and when working in full duplex mode, the CSMA/CD block will be simultaneously using its data path transmit and receive interfaces. Statistical counters are kept by the CSMA/CD block, and are readable through the appropriate register. The counters are four bits each, and can generate an interrupt when reaching their maximum values. Software can use that interrupt to update statistics in memory, or it can keep the counter interrupt disabled, while relying on the transmit interrupt routine reading the counters. Given that the counters can increment only once per transmit, this technique is a good complement for the single interrupt per sequence strategy. The interface between the CSMA/CD block and memory is word oriented. Two bi-directional FIFOs make the data path interface. Whenever a normal collision occurs (less than 16 retries), the CSMA/CD will trigger the backoff logic and will indicate the DMA logic of the collision. The DMA is responsible for restarting the data transfer into the CSMA/CD block regardless of whether the collision happened on the preamble or not. Only when 16 retries are reached, the CSMA/CD block will clear the TXENA bit, and CPU intervention is required. The DMA will not automatically restart data transfer in this case, nor will it transmit the next enqueued packet until TXENA is set by the CPU. The DMA will move the packet number in question from the TX FIFO into the TX completion FIFO. SMSC DS - LAN91C93I Page 73 DATASHEET Rev. 09/30/2002 Non-PCI Single-Chip Full Duplex Ethernet Controller 9.9 Network Interface The LAN91C93I includes both an AUI interface for thick and thin coax applications and a 10BASE-T interface for twisted pair applications. Functions common to both are: 9.10 1. Manchester encoder/decoder to convert NRZ data to Manchester encoded data and back. 2. A 32ms jabber timer to prevent inadvertently long transmissions. When 'jabbing' occurs, the transmitter is disabled, automatic loopback is disabled (in 10BASE-T mode), and a collision indication is given to the controller. The interface 'unjabs' when the transmitter has been idle for a minimum of 256 ms. 3. A phase-lock loop to recover data and clock from the Manchester data stream with up to plus or minus 18ns of jitter. 4. Diagnostic loopback capability. 5. LED drivers for collision, transmission, reception, and jabber. 10base-T The 10BASE-T interface conforms to the twisted pair MAU addendum to the 802.3 specification. On the transmission side, it converts the NRZ data from the controller to Manchester data and provides the appropriate signal level for driving the media. Signal are predistorted before transmission to minimize ISI. The collision detection circuitry monitors the simultaneous occurrence of received signals and transmitted data on the media. During transmission, data is automatically looped back to the receiver except during collision periods, in which case the input to the receiver is network data. During collisions, should the receive input go idle prior to the transmitter going idle, input to the receiver switches back to the transmitter within nine bit times. Following transmission, the transmitter performs a SQE test. This test exercises the collision detection circuitry within the 10BASE-T interface. The receiver monitors the media at all times. It recovers the clock and data and passes it along to the controller. In the absence of any receive activity, the transmitter is looped back to the receiver. In addition, the receiver performs automatic polarity correction. The 10BASE-T interface performs link integrity tests per section 14.2.1.7 of 802.3, using the following values: 1. Link_loss_timer: 64 ms 2. Link_test_min_timer: 4 ms 3. Link_count: 2 4. Link_test_max_timer: 64 ms The state of the link is reflected in the EPHSR. 9.11 AUI The LAN91C93I also provides a standard six wire AUI interface to a coax transceiver. Rev. 09/30/2002 Page 74 DATASHEET SMSC DS - LAN91C93I Non-PCI Single-Chip Full Duplex Ethernet Controller 9.12 Physical Interface The internal physical interface (PHY) consists of an encoder/decoder (ENDEC) and an internal 10BASE-T transceiver. The ENDEC also provides a standard 6-pin AUI interface to an external coax transceiver for 10BASE-2 and 10BASE-5 applications. The PHY functions can be divided into transmit and receive functions. 9.13 Transmit Functions 9.13.1 Manchester Encoding The PHY encodes the transmit data received from the MAC. The encoded data is directed internally to the selected output driver for transmission over the twisted-pair network or the AUI cable. Data transmission and encoding is initiated by the Transmit Enable input, TXE, going low. 9.13.2 Transmit Drivers The encoded transmit data passes through to the transmit driver pair, TPETXP(N), and its complement, TPETXDP(N). Each output of the transmit driver pair has a source resistance of 10 ohms maximum and a current rating of 25 mA maximum. The degree of predistortion is determined by the termination resistors; the equivalent resistance should be 100 ohms. 9.13.3 Jabber Function This integrated function prevents the DTE from locking into a continuous transmit state. In 10BASE-T mode, if transmission continues beyond the specified time limit, the jabber function inhibits further transmission and asserts the collision indicator nCOLL. The limits for jabber transmission are 20 to 15 ms in 10BASE-T mode. In the AUI mode, the jabber function is performed by the external transceiver. 9.13.4 SQE Function In the 10BASE-T mode, the PHY supports the signal quality error (SQE) function. At the end of a transmission, the PHY asserts the nCOLL signal for 10+/-5 bit times beginning 0.6 to 1.6ms after the last positive transition of a transmitted frame. In the AUI mode, the SQE function is performed by the external transceiver. 9.14 Receive Functions 9.14.1 Receive Drivers Differential signals received off the twisted-pair network or AUI cable are directed to the internal clock recovery circuit prior to being decoded for the MAC. SMSC DS - LAN91C93I Page 75 DATASHEET Rev. 09/30/2002 Non-PCI Single-Chip Full Duplex Ethernet Controller 9.14.2 Manchester Decoder and Clock Recovery The PHY performs timing recovery and Manchester decoding of incoming differential signals in 10BASE-T or AUI modes, with its built-in phase-lock loop (PLL). The decoded (NRZ) data, RXD, and the recovered clock, RXCLK, becomes available to the MAC, typically within 9 bit times (5 for AUI) after the assertion of nCRS. The receive clock, RXCLK, is phase-locked to the transmit clock in the absence of a received signal (idle). 9.14.3 Squelch Function The integrated smart squelch circuit employs a combination of amplitude and timing measurements to determine the validity of data received off the network. It prevents noise at the differential inputs from falsely triggering the decoder in the absence of valid data or link test pulses. Signal levels below 300mV (180mV for AUI) or pulse widths less than 15ns at the differential inputs are rejected. Signals above 585mV (300mV for AUI) and pulse widths greater than 30ns will be accepted. When using the extended cable mode with 10BASE-T media which extends beyond the standard limit of 100 meters, the squelch level can optionally be set to reject signals below 180mV and accept signals above 300mV. If the input signal exceeds the squelch requirements, the carrier sense output, nCRS, is asserted. 9.14.4 Reverse Polarity Function In the 10BASE-T mode, the PHY monitors for receiver polarity reversal due to crossed wires and corrects by reversing the signal internally. 9.14.5 Collision Detection Function In the 10BASE-T mode, a collision state is indicated when there are simultaneous transmissions and receptions on the twisted pair link. During a collision state, the nCOLL signal is asserted. If the received data ends and the transmit control signal is still active, the transmit data is sent to the MAC within 9 bit times. The nCOLL signal is de-asserted within 9 bit times after the collision terminates. In the AUI mode, the external transceiver sends a 10MHz signal to the PHY upon detection of a collision. 9.14.6 Link Integrity The PHY test for a faulty twisted-pair link. In the absence of transmit data, link test pulses are transmitted every 16+/-8ms after the end of the last transmission or link pulse on the twisted pair medium. If neither valid data nor link test pulses are received within 10 to 150ms, the link is declared bad and both data transmission as well as the operational loopback function are disabled. The Link Integrity function can be disabled for pre-10BASE-T twisted-pair networks. Rev. 09/30/2002 Page 76 DATASHEET SMSC DS - LAN91C93I Non-PCI Single-Chip Full Duplex Ethernet Controller Chapter 10 Board Setup Information The following parameters are obtained from the EEPROM as board setup information: ETHERNET INDIVIDUAL ADDRESS REGISTER I/O BASE ADDRESS Configuration Register ROM BASE ADDRESS 8/16 BIT ADAPTER 10BASE-T or AUI INTERFACE Base Register EEPROM WORD ADDRESS IOS Value * 4 (IOS Value *4) + 1 INTERRUPT LINE SELECTION All the above mentioned values are read from the EEPROM upon hardware reset. Except for the INDIVIDUAL ADDRESS, the value of the IOS switches determines the offset within the EEPROM for these parameters, in such a way that many identical boards can be plugged into the same system by just changing the IOS jumpers. In order to support a software utility based installation, even if the EEPROM was never programmed, the EEPROM can be written using the LAN91C93I. One of the IOS combination is associated with a fixed default value for the key parameters (I/O BASE, ROM BASE, INTERRUPT) that can always be used regardless of the EEPROM based value being programmed. This value will be used if all IOS pins are left open or pulled high. The EEPROM is arranged as a 64 x 16 array. The specific target device is the 9346 1024-bit Serial EEPROM. All EEPROM accesses are done in words. All EEPROM addresses shown are specified as word addresses. INDIVIDUAL ADDRESS - 20-22 hexIf IOS2-0 = 7, only the INDIVIDUAL ADDRESS is read from the EEPROM. Currently assigned values are assumed for the other registers. These values are default if the EEPROM read operation follows hardware reset. The EEPROM SELECT bit is used to determine the type of EEPROM operation: a) normal or b) general purpose register. a. NORMAL EEPROM OPERATION - EEPROM SELECT bit = 0 On EEPROM read operations (after reset or after setting RELOAD high) the CONFIGURATION REGISTER and BASE REGISTER are updated with the EEPROM values at locations defined by the IOS2-0 pins. The INDIVIDUAL ADDRESS registers are updated with the values stored in the INDIVIDUAL ADDRESS area of the EEPROM. On EEPROM write operations (after setting the STORE bit) the values of the CONFIGURATION REGISTER and BASE REGISTER are written in the EEPROM locations defined by the IOS2-0 pins. The three least significant bits of the CONTROL REGISTER (EEPROM SELECT, RELOAD and STORE) are used to control the EEPROM. Their values are not stored nor loaded from the EEPROM. b. GENERAL PURPOSE REGISTER - EEPROM SELECT bit = 1 On EEPROM read operations (after setting RELOAD high) the EEPROM word address defined by the POINTER REGISTER 6 least significant bits is read into the GENERAL PURPOSE REGISTER. SMSC DS - LAN91C93I Page 77 DATASHEET Rev. 09/30/2002 Non-PCI Single-Chip Full Duplex Ethernet Controller On EEPROM write operations (after setting the STORE bit) the value of the GENERAL PURPOSE REGISTER is written at the EEPROM word address defined by the POINTER REGISTER 6 least significant bits. RELOAD and STORE are set by the user to initiate read and write operations respectively. Polling the value until read low is used to determine completion. When an EEPROM access is in progress the STORE and RELOAD bits of CTR will read-back as both bits high. No other bits of the LAN91C93I can be read or written until the EEPROM operation completes and both bits are clear. This mechanism is also valid for reset initiated reloads. Note: If no EEPROM is connected to the LAN91C93I, the ENEEP pin should be grounded and no accesses to the EEPROM will be attempted. Configuration, Base and Individual Addresses assume their default values upon hardware reset and the CPU is responsible for programming them for their final value. 10.1 Diagnostic LEDs The following LED drive signals are available for diagnostic and installation aid purposes: nTXLED - Activated by transmit activity. nBSELED - Board select LED. Activated when the board space is accessed, namely on accesses to the LAN91C93I register space or the ROM area decoded by the LAN91C93I. The signal is stretched to 125 msec. nRXLED - Activated by receive activity. nLINKLED - Reflects the link integrity status. 10.2 Bus Clock Considerations The arbiter exploits the sequential nature of the CPU accesses to provide a very fast access time. Memory bandwidth considerations will have an effect on the CPU cycle time but no effect on access time. For normal 8MHz, 10MHz, and 12.5MHz LOCAL BUS, as well as EISA normal cycles, the LAN91C93I can be accessed without negating ready. See Arbitration Considerations in Functional Description of the Blocks for more details. Rev. 09/30/2002 Page 78 DATASHEET SMSC DS - LAN91C93I Non-PCI Single-Chip Full Duplex Ethernet Controller 16 BITS IOS2-0 W ORD ADDRESS 000 0h CONFIGURATION REG. 1h BASE REG. 4h CONFIGURATION REG. 5h BASE REG. 8h CONFIGURATION REG. 9h BASE REG. Ch CONFIGURATION REG. Dh BASE REG. 10h CONFIGURATION REG. 11h BASE REG. 14h CONFIGURATION REG. 15h BASE REG. 18h CONFIGURATION REG. 19h BASE REG. 20h IA0-1 21h IA2-3 22h IA4-5 001 010 011 100 101 110 XXX Figure 10.1 - 64 X 16 Serial EEPROM Map SMSC DS - LAN91C93I Page 79 DATASHEET Rev. 09/30/2002 Non-PCI Single-Chip Full Duplex Ethernet Controller Chapter 11 Operational Description 11.1 Maximum Guaranteed Ratings* Operating Temperature Range ................................................................................................-40C to 85C Storage Temperature Range ...............................................................................................-55C to +150C Lead Temperature Range (soldering, 10 seconds) ............................................................................+325C Positive Voltage on any pin, with respect to Ground .....................................................................VCC + 0.3V Negative Voltage on any pin, with respect to Ground ........................................................................... -0.3V Maximum VCC .......................................................................................................................................... +7V * Stresses above those listed above could cause permanent damage to the device. This is a stress rating only and functional operation of the device at any other condition above those indicated in the operation sections of this specification is not implied. Note: When powering this device from laboratory or system power supplies, it is important that the Absolute Maximum Ratings not be exceeded or device failure can result. Some power supplies exhibit voltage spikes on their outputs when the AC power is switched on or off. In addition, voltage transients on the AC power line may appear on the DC output. If this possibility exists, it is suggested that a clamp circuit be used. 11.2 DC Electrical Characteristics (TA =-40C to 85C, VCC = +5.0 V 10%, or VCC = +3.3 V 10%) PARAMETER Input Voltage Levels for Vcc = 5.0V I Type Input Buffer Low Input Level High Input Level IS Type Input Buffer Low Input Level High Input Level Schmitt Trigger Hysteresis ICLK Input Buffer SYMBOL MIN VILI VIHI 2.0 VILIS VIHIS VHYS Low Input Level VILCK High Input Level VIHCK TYP MAX UNITS COMMENTS 0.8 V V TTL Levels 0.8 V V mV Schmitt Trigger Schmitt Trigger 0.4 V 2.2 250 3.3 V Input Voltage Levels for Vcc = 3.3V I Type Input Buffer Low Input Level VILI High Input Level VIHI Rev. 09/30/2002 0.8 2.0 Page 80 DATASHEET V V SMSC DS - LAN91C93I Non-PCI Single-Chip Full Duplex Ethernet Controller PARAMETER IS Type Input Buffer SYMBOL Low Input Level VILIS High Input Level VIHIS Schmitt Trigger Hysteresis VHYS MIN TYP MAX UNITS COMMENTS 0.8 V Schmitt Trigger V Schmitt Trigger 2.0 165 mV ICLK Input Buffer Low Input Level VILCK 0.3 V High Input Level VIHCK 2.0 Low Input Leakage IIL -10 +10 A VIN = 0 High Input Leakage IIH -10 +10 A VIN = VCC Low Input Leakage IIL -10 +10 A VIN = 0 High Input Leakage IIH -10 +10 A VIN = VCC IIL -150 A VIN = 0 A VIN = VCC A VIN = 0 +100 A VIN = VCC 0.4 V IOL = 4 mA V Input Leakage for Vcc = 5.0V Input Leakage (All I and IS buffers except pins with pullups/pulldowns) Input Leakage for Vcc = 3.3V Input Leakage (All I and IS buffers except pins with pullups/pulldowns) Input Current for Vcc = 5.0V IP Type Buffers Input Current -50 ID Type Buffers Input Current IIH +50 +150 Input Current for Vcc = 3.3V IP Type Buffers Input Current IIL -100 -50 ID Type Buffers Input Current IIH +50 Output Voltage for Vcc = 5.0V I/O4 Type Buffer Low Output Level VOL High Output Level VOH 2.4 Output Leakage ILEAK -10 V IOH = -2 mA +10 A VIN = 0 to VCC 0.5 V IOL = 24 mA V IOH = -12 mA +10 A VIN = 0 to VCC I/O24 Type Buffer Low Output Level VOL High Output Level VOH 2.4 Output Leakage ILEAK -10 O24 Type Buffer Low Output Level VOL High Output Level VOH 2.4 Output Leakage ILEAK -10 SMSC DS - LAN91C93I 0.5 +10 Page 81 PRELIMINARY V IOL = 24 mA V IOH = -12 mA A VIN = 0 to VCC Rev. 09/30/2002 Non-PCI Single-Chip Full Duplex Ethernet Controller PARAMETER SYMBOL MIN TYP MAX UNITS COMMENTS 0.4 V IOL = 4 mA V IOH = -2 mA +10 A VIN = 0 to VCC 0.5 V IOL = 16 mA +10 A VIN = 0 to VCC 0.5 V IOL = 16 mA V IOH = -2 mA +10 A VIN = 0 to VCC 0.5 V IOL = 24 mA +10 A VIN = 0 to VCC 0.4 V IOL = 2 mA V IOH = -1 mA +10 A VIN = 0 to VCC O4 Type Buffer Low Output Level VOL High Output Level VOH 2.4 Output Leakage ILEAK -10 OD16 Type Buffer Low Output Level VOL Output Leakage ILEAK -10 O162 Type Buffer Low Output Level VOL High Output Level VOH 2.4 Output Leakage ILEAK -10 OD24 Type Buffer Low Output Level VOL Output Leakage ILEAK -10 Output Voltage for Vcc = 3.3V I/O4 Type Buffer Low Output Level VOL High Output Level VOH 2.4 Output Leakage ILEAK -10 I/O24 Type Buffer Low Output Level VOL High Output Level VOH 2.4 0.5 Output Leakage ILEAK -10 +10 V IOL = 16 mA V IOH = -6 mA A VIN = 0 to VCC O24 Type Buffer Low Output Level VOL High Output Level VOH 2.4 0.5 Output Leakage ILEAK -10 V IOL = 12 mA V IOH = -6 mA +10 A VIN = 0 to VCC 0.4 V IOL = 2 mA V IOH = -1 mA +10 A VIN = 0 to VCC 0.5 V IOL = 8 mA +10 A VIN = 0 to VCC 0.5 V IOL = 8 mA V IOH = -1 mA +10 A VIN = 0 to VCC 0.5 V IOL = 12 mA +10 A VIN = 0 to VCC O4 Type Buffer Low Output Level VOL High Output Level VOH 2.4 Output Leakage ILEAK -10 OD16 Type Buffer Low Output Level VOL Output Leakage ILEAK -10 O162 Type Buffer Low Output Level VOL High Output Level VOH 2.4 Output Leakage ILEAK -10 OD24 Type Buffer Low Output Level VOL Output Leakage ILEAK Rev. 09/30/2002 -10 Page 82 DATASHEET SMSC DS - LAN91C93I Non-PCI Single-Chip Full Duplex Ethernet Controller PARAMETER SYMBOL MIN TYP MAX UNITS COMMENTS ICC 50 95 mA All outputs open ICSBY 4 ICC 20 ICSBY 1.5 mA ICX2H TBD mA ICX2L TBD mA XTAL2 Output Drive High ICX2H -6 mA @2.4V XTAL2 Output Drive Low ICX2L 3 mA @0.4V Supply Current for Vcc = 5.0V Supply Current Active Supply Current Standby mA Supply Current for Vcc = 3.3V Supply Current Active Supply Current Standby 64 mA All outputs open. XTAL2 Output Drive for Vcc = 5.0V XTAL2 Output Drive High XTAL2 Output Drive Low cc XTAL2 Output Drive for V = 3.3V CAPACITANCE TA = 25C; fc = 1MHz; VCC = 5V, or VCC = +3.3V PARAMETER Clock Input Capacitance (XTAL1) Clock Output Capacitance (XTAL2) Input Capacitance Output Capacitance SYMBOL CCIN MIN LIMITS TYP MAX 5 6 CCOUT CIN COUT 5 6 10 20 UNIT pF TEST CONDITION All pins except pin under test tied to AC ground pF pF pF VCC = 5V +/- 10% PARAMETER MIN TYP MAX UNITS 10BASE-T Receiver Threshold Voltage Receiver Squelch Receiver Common Mode Range Transmitter Output: Voltage Source Resistance Transmitter Output DC Offset Transmitter Backswing Voltage to Idle Differential Input Voltage 300 0 2 100 400 2.5 0.585 585 VDD 3 10 50 100 3 mV mV V ohms mV mV V AUI Receiver Threshold Voltage Receiver Squelch Receiver Common Mode Range 180 0 0.45 Transmitter Output Voltage (R=78) Transmitter Backswing Voltage to Idle Input Differential Voltage Output Short Circuit (to VCC or GND) Current 0.3 Differential Idle Voltage (measured 8.0 s after last positive transition of data frame) SMSC DS - LAN91C93I Page 83 PRELIMINARY 60 240 0.85 300 VDD 1.2 100 1.2 150 40 mV mV V mV V mA mV Rev. 09/30/2002 Non-PCI Single-Chip Full Duplex Ethernet Controller VCC = 3.3V +/- 10% PARAMETER MIN TYP MAX UNITS 10BASE-T Receiver Threshold Voltage Receiver Squelch Receiver Common Mode Range Transmitter Output: Voltage Source Resistance Transmitter Output DC Offset Transmitter Backswing Voltage to Idle Differential Input Voltage 225 0 +/- 1.3 TBD 260 +/- 1.5 +/- 0.520 520 Vdd +/- 1.6 10 50 100 +/- 3 mV mV V ohms mV mV V AUI Receiver Threshold Voltage Receiver Squelch Receiver Common Mode Range 120 0 +/- 0.39 Transmitter Output Voltage (R=78) Transmitter Backswing Voltage to Idle Input Differential Voltage Output Short Circuit (to VCC or GND) Current +/- 0.25 Differential Idle Voltage (measured 8.0 s after last positive transition of data frame) TBD 140 +/- 0.47 160 Vdd +/- 0.55 100 +/- 0.990 TBD 40 mV mV V mV V mA mV CAPACITIVE LOAD ON OUTPUTS nIOCS16, IOCHRDY 240 pF INTR 120 pF All other outputs 45 Pf Rev. 09/30/2002 Page 84 DATASHEET SMSC DS - LAN91C93I Non-PCI Single-Chip Full Duplex Ethernet Controller Chapter 12 Timing Diagrams A0-15 AEN, nSBHE VALID ADDRESS VALID ADDRESS t4 t15 nIOCS16 nIORD t20 t3 t6 t5 D0-15 VALID DATA OUT Z Parameter t3 t4 t5 t6 t15 t20 Z VALID DATA OUT min typ Address, nSBHE, AEN Setup to Control Active10 Address, nSBHE, AEN Hold after Control 20 Inactive nIORD Low to Valid Data nIORD High to Data Floating A4-A15, AEN Low Low 185 Cycle time* max units ns ns 25 15 12 ns ns ns ns IOCHRDY not used - t20 has to be met *Note: The cycle time is defined only for consecutive accesses to the Data Register. These values assume that IOCHRDY is not used. Figure 12.1 - Local Bus Consecutive Read Cycles SMSC DS - LAN91C93I Page 85 PRELIMINARY Rev. 09/30/2002 Non-PCI Single-Chip Full Duplex Ethernet Controller A0-15 AEN, nSBHE VALID ADDRESS VALID ADDRESS t4 t15 nIOCS16 t3 t20 nIOWR t7 D0-15 t8 VALID DATA VALID DATA IN Parameter min 10 5 ns ns t7 t8 t15 Address, nSBHE, AEN Setup to Control Active Address, nSBHE, AEN Hold after Control Inactive Data Setup to nIOWR Rising Data Hold after nIOWR Rising A4-A15, AEN Low 5 5 ns ns ns t20 Cycle time* 185 t3 t4 typ max 12 units ns IOCHRDY not used - t20 has to be met *Note: The cycle time is defined only for consecutive accesses to the Data Register. These values assume that IOCHRDY is not used. Figure 12.2 - Local Bus Consecutive Write Cycles Rev. 09/30/2002 Page 86 DATASHEET SMSC DS - LAN91C93I Non-PCI Single-Chip Full Duplex Ethernet Controller A0-15 AEN, nSBHE VALID ADDRESS VALID ADDRESS nIOCS16 t20 nIORD nIOWR t9 Z Z t10 IOCHRDY D0-D15 Z VALID DATA Parameter t9 t10 t20 Z Z VALID DATA min Control Active to IOCHRDY Low IOCHRDY Low Pulse Width* Cycle time** 100 185 typ max units 12 150 ns ns ns *Note: Assuming NO WAIT ST = 0 in configuration register and cycle time observed. **Note: The cycle time is defined only for accesses to the Data Register as follows: For Data Register Read - From nIORD falling to next nIORD falling For Data Register Write - From nIOWR rising to next nIOWR rising Figure 12.3 - Local Bus Consecutive Read and Write Cycles SMSC DS - LAN91C93I Page 87 PRELIMINARY Rev. 09/30/2002 Non-PCI Single-Chip Full Duplex Ethernet Controller A0-15 (ISA) AEN, nSBHE VALID ADDRESS nIOCS16 nIORD IOCHRDY t9 Z t18 Z t19 VALID DATA OUT D0-D15 Parameter t9 t18 t19 min typ Control Active to IOCHRDY Low IOCHRDY Width when Data is Unavailable at Data Register Valid Data to IOCHRDY Inactive max units 15 ns 575 225 ns ns IOCHRDY is used instead of meeting t20 and t43. "No Wait St' bit is 1 - IOCHRDY only negated if needed and only for Data Register access. Figure 12.4 - Data Register Special Read Access Rev. 09/30/2002 Page 88 DATASHEET SMSC DS - LAN91C93I Non-PCI Single-Chip Full Duplex Ethernet Controller A0-15 (ISA) AEN, nSBHE VALID ADDRESS nIOCS16 nIOWR t9 IOCHRDY t18 Z D0-D15 VALID DATA IN Parameter t9 t18 Z min typ Control Active to IOCHRDY Low IOCHRDY Width when Data Register is Full max units 15 425 ns ns IOCHRDY is used instead of meeting t20 and t44. 'No Wait St' bit is 1 - IOCHRDY only negated if needed and only for Data Register access. Figure 12.5 - Data Register Special Write Access SMSC DS - LAN91C93I Page 89 PRELIMINARY Rev. 09/30/2002 Non-PCI Single-Chip Full Duplex Ethernet Controller A0-15 (ISA) AEN VALID ADDRESS VALID ADDRESS t3 nIOWR t3 nIORD t7 t8 t5 Z D0-7 Parameter t3 t5 t7 t8 Z VALID DATA OUT min Address, nSBHE, AEN Setup to Control Active nIORD Low to Valid Data Data Setup to nIOWR Rising Data Hold after nIOWR Rising VALID DATA IN typ max 25 40 30 9 units ns ns ns ns Figure 12.6 - 8-Bit Mode Register Cycles Rev. 09/30/2002 Page 90 DATASHEET SMSC DS - LAN91C93I Non-PCI Single-Chip Full Duplex Ethernet Controller EESK EEDO EEDI EECS t21 t68 Parameter min typ max t21 EESK Falling to EECS Changing 0 15 t68 EESK Falling to EEDO Changing 0 25 units ns 9346 is typically the serial EEPROM used. Figure 12.7 - EEPROM Read SMSC DS - LAN91C93I Page 91 PRELIMINARY Rev. 09/30/2002 Non-PCI Single-Chip Full Duplex Ethernet Controller A0-19 ADDRESS VALID t3 t4 nMEMRD D0-15 t3 t4 t16 t17 Z Parameter min Address Setup to Control Active Address Hold after Control Inactive nMEMRD Low to nROM Low(Internal) nMEMRD High to nROM High(Internal) 10 20 0 0 typ max units 20 35 ns ns ns ns Figure 12.8 - External ROM Read Access Rev. 09/30/2002 Page 92 DATASHEET SMSC DS - LAN91C93I Non-PCI Single-Chip Full Duplex Ethernet Controller EESK EEDO EEDI EECS t70 t69 Parameter min typ max units ns t69 EESK Falling to EECS Changing 5 t70 EESK Falling to EEDO Changing 20 9346 is typically the serial EEPROM used. Figure 12.9 - EEPROM Write SMSC DS - LAN91C93I Page 93 PRELIMINARY Rev. 09/30/2002 Non-PCI Single-Chip Full Duplex Ethernet Controller TPETXP t31 t31 TPETXN t32 t32 TPETXDN t33 t33 TPETXDP TWISTED PAIR DRIVERS TXP t34 t34 TXN AUI DRIVERS Parameter t31 t32 t33 t34 min TPETXP to TPETXN Skew TPETXP(N) to TPETXDP(N) Delay TPETXDN to TPETXDP Skew TXP to TXN Skew -1 47 -1 -1.5 typ max units +1 53 +1 1.5 ns ns ns ns Figure 12.10 - Differential Output Signal Timing (10BASE-T and AUI) Rev. 09/30/2002 Page 94 DATASHEET SMSC DS - LAN91C93I Non-PCI Single-Chip Full Duplex Ethernet Controller 1 0 1 1 0 1 0 1 0 1 0 1 0 1 0 RECP RECN t35 first bit decoded nCRS (internal) t36 1 0 1 1 0 1 0 TPERXP(N) t37 nCRS (internal) first bit decoded t38 Parameter t35 t36 t37 t38 Noise Pulse Width Reject (AUI) Carrier Sense Turn On Delay (AUI) Noise Sense Pulse Width Reject (10BASE-T) Carrier Sense Turn On Delay (10BASE-T) min typ max units 15 50 15 450 25 70 25 500 30 100 30 550 ns ns ns ns Figure 12.11 - Receive Timing - Start of Frame (AUI and 10BASE-T) SMSC DS - LAN91C93I Page 95 PRELIMINARY Rev. 09/30/2002 Non-PCI Single-Chip Full Duplex Ethernet Controller last bit b a 1/0 TPERXP TPERXN RECP RECN t39 nCRS (internal) Parameter t39 min 200 Receiver Turn Off Delay typ max units 300 ns Figure 12.12 - Receive Timing - End of Frame (AUI and 10BASE-T) Rev. 09/30/2002 Page 96 DATASHEET SMSC DS - LAN91C93I Non-PCI Single-Chip Full Duplex Ethernet Controller t40 t41 TPETXP TPETXN last bit b a 1/0 TXP TXN Parameter t40 t41 min Transmit Output High to Idle in Half-Step Mode Transmit Output High before Idle in Half-Step Mode typ max units 800 ns ns 200 Figure 12.13 - Transmit Timing - End of Frame (AUI and 10BASE-T) SMSC DS - LAN91C93I Page 97 PRELIMINARY Rev. 09/30/2002 Non-PCI Single-Chip Full Duplex Ethernet Controller COLLP COLLN t42 t43 COL (internal) Parameter t42 t43 min typ Collision Turn On Delay Collision Turn Off Delay max units 50 350 ns ns Figure 12.14 - Collision and Timing (AUI) ADDRESS POINTER REGISTER DATA REGISTER nIOWR t44 nIORD IOCHRDY/ nWAIT (Z) Parameter t44 min Pointer Register Reloaded to a Word of Data Prefetched into Data Register typ 2 * t20 max units ns Note: If t44 is not met, IOCHRDY will be negated for the required time. This parameter can be ignored if IOCHRDY is connected to the system. Figure 12.15 - Memory Read Timing Rev. 09/30/2002 Page 98 DATASHEET SMSC DS - LAN91C93I Non-PCI Single-Chip Full Duplex Ethernet Controller t1 t2 t2 CLOCK tR tF Figure 12.16 - Input Clock Timing NAME t1 t2 tR, tF DESCRIPTION Clock Cycle Time for 20 MHz Clock High Time/Low Time for 20 MHz Clock Rise Time/Fall Time Xtal1 Startup time (from 1.6v of Vcc rising) Xtal1 Capture Range (Xtal1 frequency variation) Xtal Internal feedback resistor ADDRESS MIN TYP 50 MAX 19.7 20/30 5 50 20.3 UNITS ns ns ns msec MHz 1 3 Meg Ohm 30/20 DATA REGISTER POINTER REGISTER nIOWR t45 Parameter t45 min Last Access to Data Register to Pointer Reloaded typ 2 * t20 max units ns Figure 12.17 - Memory Write Timing SMSC DS - LAN91C93I Page 99 PRELIMINARY Rev. 09/30/2002 Non-PCI Single-Chip Full Duplex Ethernet Controller A A1 A2 D D1 E E1 H L L1 e MIN ~ 0.05 2.55 23.65 19.90 17.65 13.90 0.11 0.73 ~ NOMINAL ~ ~ ~ ~ ~ ~ ~ ~ 0.88 1.95 0.65 Basic ~ MAX 3.4 0.5 3.05 24.15 20.10 18.15 14.10 0.23 1.03 ~ REMARKS Overall Package Height Standoff Body Thickness X Span X body Size Y Span Y body Size Lead Frame Thickness Lead Foot Length Lead Length Lead Pitch Lead Foot Angle 0o 7o W 0.20 ~ 0.40 Lead Width R1 0.10 ~ 0.25 Lead Shoulder Radius R2 0.15 ~ 0.40 Lead Foot Radius ccc ~ ~ 0.10 Coplanarity Notes: 1 Controlling Unit: millimeter. 2 Tolerance on the true position of the leads is 0.065 mm maximum 3 Package body dimensions D1 and E1 do not include the mold protrusion. Maximum mold protrusion is 0.25 mm. 4 Dimension for foot length L measured at the gauge plane 0.25 mm above the seating plane. 5 Details of pin 1 identifier are optional but must be located within the zone indicated. Figure 12.18 - 100 PIN QFP Package Rev. 09/30/2002 Page 100 DATASHEET SMSC DS - LAN91C93I Non-PCI Single-Chip Full Duplex Ethernet Controller MIN NOMINAL MAX REMARKS A ~ ~ 1.20 Overall Package Height A1 0.05 ~ 0.15 Standoff A2 0.95 ~ 1.05 Body Thickness D 15.80 ~ 16.20 X Span D1 13.90 ~ 14.10 X body Size E 15.80 ~ 16.20 Y Span E1 13.90 ~ 14.10 Y body Size H 0.09 ~ 0.20 Lead Frame Thickness L 0.45 0.60 0.75 Lead Foot Length L1 ~ 1.00 ~ Lead Length e 0.50 Basic Lead Pitch 0o ~ 7o Lead Foot Angle W 0.17 0.22 0.27 Lead Width R1 0.08 ~ ~ Lead Shoulder Radius R2 0.08 ~ 0.20 Lead Foot Radius ccc ~ ~ 0.08 Coplanarity Notes: 1 Controlling Unit: millimeter. 2 Tolerance on the true position of the leads is 0.04 mm maximum. 3 Package body dimensions D1 and E1 do not include the mold protrusion. Maximum mold protrusion is 0.25 mm. 4 Dimension for foot length L measured at the gauge plane 0.25 mm above the seating plane. 5 Details of pin 1 identifier are optional but must be located within the zone indicated. Figure 12.19 - 100 PIN TQFP Package SMSC DS - LAN91C93I Page 101 PRELIMINARY Rev. 09/30/2002 Non-PCI Single-Chip Full Duplex Ethernet Controller Chapter 13 LAN91C93I Revisions DATE REVISED 09/30/02 PAGE(S) 38 SECTION/FIGURE/ENTRY I/O Space - Bank1 Offset 2 CORRECTION Modified I/O base address 300h decoding 100, 101 Figure 12.18 - 100 PIN QFP Package, Figure 12.19 - 100 PIN TQFP Package Chapter 4 Description of Pin Functions IO Space Bank 2 Offset 2 - Interrupt Figure 7.2 - Interrupt Structure 8.2 8.3 Typical Flow of Events for Transmit Title and document UPDATED PIN PACKAGES 09/17/02 ADD DESCRIPTION OF RBIAS PIN 07/01/02 MODIFIED THE DESCRIPTION OF INTERRUPT REGISTERS MODIFIED INTERRUPT STRUCTURE FIGURE MODIFIED THE FLOW CHART 07/01/02 13 44 49 54 1 58 26 Figure 8.1 - Interrupt Service Routine Figure 10 26 DATA AREA IN RAM 22 Figure 5.4 37 BANK 2 OFFSET 4 - FIFO PORT REGISTER 68 DC Electrical Characteristics Rev. 09/30/2002 07/01/02 07/01/02 Non-PCI replaces ISA in title. Local Bus replaces ISA throughout document. Figure has been updated. 04/15/02 Changed Max RAM Offset to 1534 from 1536 NUMBER OF BYTES IN DATA AREA CHANGED TO 1531 FROM 2034 MODIFY FIGURE 8 07/26/01 RX FIFO USING MMU COMMANDS SHOULD BE 6) AND 8) INSTEAD OF 3) AND 4) UPDATE 3.3V CHARACTERISTICS NUMBER TO REPLACE TBD 07/26/01 Page 102 DATASHEET 04/15/02 07/26/01 07/26/01 07/26/01 SMSC DS - LAN91C93I Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Microchip: LAN91C93I-MS