PANEL SWITCHES M O M -IP 8 80 -1 IP series SW Pushbutton switches for harsh environments * bushing O 12 mm * momentary DISTINCTIVE FEATURES Illuminated or non-illuminated Tactile feedback Wide variety of configurations Flat round actuator for optional marking Sealed to IP67 and IP69K ENVIRONMENTAL SPECIFICATIONS * Front panel sealing: IP67 according to IEC 60529 IP69K according to DIN 40050-9 (non-illuminated) with cap U5125 * Shock resistance: 100 g according to IEC 512-4, test 6c * Vibration resistance: 10-500Hz - 10 g according to IEC 512-4, test 6d * Salt spray: IEC 512-6, test 11f * Robustness (non-illuminated): IK06 according to EN 62262 (1 joule) * Operating temperature: -40 C to +85 C (-40 F to +185 F) ELECTRICAL SPECIFICATIONS * Max. current/voltage rating with resistive load (gold plated silver contacts): 5 A 28 VDC, 70,000 cycles (only function 3) For W terminals, current has 0.2 A 48 VDC, 500,000 cycles to be limited to 400 mA. 0.5 A 48 VAC, 500,000 cycles * Initial contact resistance: 100 m max. * Insulation resistance: 1 G min. at 500 VDC * Dielectric strength: 1,500 Vrms * Contact bounce: 10 ms LED COMPONENT SPECIFICATIONS LED color Forward current Typ. forward voltage Max. forward voltage Super red (L0S) 20 mA 2.1 V 2.3 V Yellow (L0Y) 20 mA 2.1 V 2.3 V Green (L0G) 20 mA 2.1 V 2.3 V Blue (L0B) 20 mA 3.2 V 3.8 V White (L0W) 20 mA 3.35 V 4.25 V Red/green (LSG) 20 mA Red: 1.95 V / green: 2.1 V 2.5 V Yellow/green (LYG) 20 mA Yellow: 2 V / green: 2.1 V 2.5 V A resistor must be series-connected by the user. Resistor value = supply voltage - LED forward voltage LED forward current The company reserves the right to change specifications without notice. 1 Pushbutton switches for harsh environments* bushing O 12 mm * momentary GENERAL SPECIFICATIONS * Panel thickness: 1.5 mm (.059) min. 4 mm (.157 max.) TERMINALS ILLUMINATED MODELS * Total travel: Function 3: 1.7 mm (.067) 0.3 mm (0.012) Function 5: 1.3 mm (.051) 0.3 mm (0.012) LED Cathode (-) * Typical operating force: 6 N 2 N LED Cathode (-) Solder lug S Straight P * Low level/mech. life: 1,000,000 cycles * Torque: 1.5 Nm max. applied to nut NON-ILLUMINATED MODELS 1.00 1.00 (.039) (.039) MATERIALS 2.40 (.094) 2.40 (.094) 1.20 1.20 (.047) (.047) Quick-connect Z1 CIPCOSP CIPCOSP CIPCOSZ1 CIPCOSZ1 ELECTRICAL FUNCTIONS * Actuator: polyamide 6/6 * Bushing/bezel: zinc die-cast (zamak), black painted * Contacts: - silver, gold plated (std) - brass, gold plated (for option 104) 2.80 2.80 (.110) (.110) Straight P * Case: thermoplastic UL94-V0 8.70 (.342) 8.70 (.342) 4.55 (.179) 4.55 (.179) 5.20 (.204) 5.20 (.204) * Soldering: 320 C (608 F) max. for 3 sec. ILLUMINATED MODELS NON-ILLUMINATED MODELS * Output wires (flying lead terminals): F version: AWG20, section 0.6 mm2 W version: AWG24, section 0.23 mm2 * LED wires: F version: AWG26, section 0.12 mm2 W version: AWG24, section 0.23 mm2 Function 3 (NO) Function 3 (NO) Function 5 (NC/NO) * Lens: polycarbonate * Terminal seal: epoxy MOUNTING APEM products may be recycled at end-of-life for the re-claiming of valuable metal components. 1.50min-4Max (.059 min-.157max) PANEL CUT-OUT 12.90 (.507) AGENCY APPROVAL 2 A 125 VAC/250 VAC File E83438 See following pages. 1 O13.60 (.535DIA) O13.50 (.531DIA) MATRIX MOUNTING - BACK OF PANEL SPACE REQUIREMENT 20.00 (.787) 17.50 (.688) 20.00 (.787) 20.00 (.787) PANEL SWITCHES IP series CIPCE1 2 Pushbutton switches for harsh environments* bushing O 12 mm * momentary BUILD YOUR PART NUMBER BASIC PART NUMBER IP ELECTRICAL FUNCTIONS ACTUATOR SHAPES SERIES B Round, curved, shiny 3 Normally open (NO) C Square 5 R NC/NO combined (non-illuminated) Round, curved P Round, flat TERMINALS S Solder lugs F Flying leads, standard W Flying leads, thin P Straight PC Z1 CONTACTS AD Silver, gold plated (standard) CD Brass, gold plated (option 104) Quick-connect (non-ill., NO only ) Actuator marking available on round flat models (symbol 10 mm max.). On request. OPTIONS ACTUATOR COLORS Blank 1 Blue B Dark blue L0S Super red 2 Black L0Y Yellow 3 Green L0G Green 4 Grey L0B Blue 5 Yellow L0W White 6 Red LSG Red/green LYG Yellow/green 7/1 White 8 Bright chrome 9 Orange OPTIONS LED COLORS Non-illuminated 100 Satin chrome bezel 101 Bright chrome bezel 104 High actuator (non-illum. round models only) APPROVAL UL Consult factory for detail of approved models. Option 104 If combined with electrical function 5 (NC/NO), this option should be ordered with CD contacts (brass, gold plated). Current/voltage rating: 100 mA 30 VDC ABOUT THIS SERIES On the following pages, you will find successively basic part numbers of switches and options in the same order as in above chart. Notice: please note that not all combinations of above numbers are available. Refer to the following pages for further information. A sealing boot is available to protect the switches against frost and sand. See "Sealing Boots" section of website. Mounting accessories: Standard hardware supplied: 1 hex nut 14 mm (.551) across flats and 1 O-ring. Hex nut part number U166. 3 PANEL SWITCHES IP series Pushbutton switches for harsh environments* bushing O 12 mm * momentary 1.50 Min (.059 Min) 5.00 (.196) 17.50 (.688SQ) O12.00x0.75SI (.472DIAx0.75IS) EPOXY 1.20 (.047) 0.40 (.015) 2.00 (.078) 5.08 (.200) 5.20 (.204) 1.50 (.059) 6.10 (.240) Normally Open 6.40 6.80 (.251) (.267) IPC3SAD 12.00 (.472SQ) 2.00 (.078) FLAT SQUARE - ILLUMINATED SOLDER LUG TERMINALS Also available with straight PC terminals: IPC3PAD LED color is indicated by the bottom of the switch. 1.50 Min (.059 Min) 6.80 (.267) 5.00 (.196) 12.00 (.472SQ) O12.00x0.75SI (.472DIAx0.75IS) For THIN flying leads, replace F with W. Wire colors: black: NO contact, red: LED anode(+), blue: LED cathode(-) Shown with standard flying lead terminals. 0.40 (.015) 2.00 (.078) 5.08 (.200) 5.20 (.204) EPOXY 1.20 (.047) IPC5FAD NC/NO combined 2.00 (.078) O12.00x0.75SI (.472DIAx0.75IS) NO 50010 (19.68.393) 5.00 (.196) Normally Open 6.80 (.267) IPC3FAD 12.00 (.472SQ) 1.50 Min (.059 Min) FLAT SQUARE - NON ILLUMINATED FLYING LEAD TERMINALS 4 17.50 (.688SQ) O12.00x0.75SI (.472DIAx0.75IS) 6.10 (.240) Also available with straight PC terminals: IPC3PAD (NO) or IPC5PAD (NC/NO) and quick-connect terminals: IPC3Z1AD (NO only) For THIN flying leads, replace F with W. Wire colors (NC/NO): black: NO, blue: NC. Shown with standard flying lead terminals. 1.50 Min (.059 Min) 5.00 (.196) Normally Open 6.40 6.80 (.251) (.267) Normally Open 1.50 (.059) IPC5SAD 12.00 (.472SQ) 2.00 (.078) FLAT SQUARE - NON ILLUMINATED SOLDER LUG TERMINALS IPC3SAD 17.50 (.688SQ) 50010 (19.68.393) Normally Open 16.00 Max (.629 Max) IPC3FAD 2.00 (.078) FLAT SQUARE - ILLUMINATED FLYING LEAD TERMINALS 16.00 Max (.629 Max) PANEL SWITCHES IP series NC/NO 17.50 (.688SQ) Pushbutton switches for harsh environments* bushing O 12 mm * momentary 1.50 Min (.059 Min) O12.00x0.75SI (.472DIAx0.75IS) 1.50 (.059) Also available with straight PC terminals: IPR3PAD LED colour is indicated by the bottom of the switch. EPOXY 1.20 (.047) 0.40 (.015) 2.00 (.078) 5.08 (.200) 1.50 Min (.059 Min) 6.80 (.267) 5.00 (.196) O12.00 (.472DIA) 50010 (19.68.393) For THIN flying leads, replace F with W. Wire colors: black: NO contact, red: LED anode(+), blue: LED cathode(-) Shown with standard flying lead terminals. IPR5SAD Flat actuator, NO IPP3SAD IPP5SAD O17.50 (.688DIA) O12.00x0.75SI (.472DIAx0.75IS) NO NC EPOXY 1.20 (.047) 2.00 (.078) 0.40 (.015) 5.08 (.200) NO NO 5.20 (.204) Curved actuator, NC/NO 1.50 Min (.059 Min) IPR3SAD 1.50 (.059) Curved actuator, NO 6.40 6.80 (.251) (.267) 5.00 (.196) O12.00 (.472DIA) 2.00 (.078) FLAT ROUND - NON ILLUMINATED SOLDER LUG TERMINALS Flat actuator, NC/NO O17.50 (.688DIA) O12.00x0.75SI (.472DIAx0.75IS) 16.00 Max (.629 Max) Normally Open 2.00 (.078) FLAT ROUND - ILLUMINATED FLYING LEAD TERMINALS IPR3FAD O17.50 (.688DIA) 5.20 (.204) Normally Open 6.10 (.240) IPR3SAD 6.40 6.80 (.251) (.267) 5.00 (.196) O12.00 (.472DIA) 2.00 (.078) FLAT ROUND - ILLUMINATED SOLDER LUG TERMINALS PANEL SWITCHES IP series NC/NO Also available with straight PC terminals: IPC3PAD (NO) or IPC5PAD (NC/NO) and quick-connect terminals: IPC3Z1AD (NO only) Flat actuator, NO IPP3FAD Flat actuator, NC/NO IPP5FAD For THIN flying leads, replace F with W. Wire colors (NC/NO): black: NO, blue: NC Shown with standard flying lead terminals. O12.00x0.75SI (.472DIAx0.75IS) NO 50010 (19.68.393) IPR5FAD 2.00 (.078) 5.00 (.196) Curved actuator, NC/NO 6.80 (.267) IPR3FAD O17.50 (.688DIA) 13.20 (.519) Curved actuator, NO O12.00 (.472DIA) 1.50 Min (.059 Min) FLAT ROUND - NON ILLUMINATED FLYING LEAD TERMINALS NC/NO B1 5 PANEL SWITCHES IP series Pushbutton switches for harsh environments* bushing O 12 mm * momentary ACTUATOR COLORS BASIC P/N 1 B 2 3 4 5 Blue Dark blue Black Green Grey Yellow 6 7/1 8 9 A Red White Bright chrome Orange Satin chrome LED COLORS BASIC P/N Blank Non-illuminated L0S Super red L0Y Yellow L0G Green L0B Blue L0W White LSGRed/green LYGYellow/green OPTIONS O12.00 (.472DIA) 104 IPR O12.00 (.472DIA) 4.70 (.185) 100 Satin chrome bezel 101 Bright chrome bezel 104 High actuator - For round, non-illuminated only If combined with function 5 (NC/NO), order with CD contacts (instead of AD contacts). 4.70 (.185) BASIC P/N 104 IPP AGENCY APPROVAL BASIC P/N UL Consult factory for details of approved models. To order switches marked UL, complete above box with "UL". 6