VM534D - Artesyn Technologies, Inc.

PM500 INPUT VOLTAGE SUFFIX

115±10VAC (NONE)

220±20VAC D

240±20VAC K

VM500 Series only

VM534D INPUT VOLTAGE SUFFIX

200 to 233VAC D

OUTPUT SPECIFICATIONS

Voltage accuracy ±1.0% max.

Voltage adjustability PM529 and PM563 only Yes

Line regulation See table

Load regulation See table

Temperature coefficient ±0.02%/°C

Overvoltage protection See table on facing 6.2V typical

page for relevant models

Output power limit Typical 130% to 200% FL

Short circuit protection Switch off/on 100% to 200% FL

INPUT SPECIFICATIONS

Input voltage range See tables below

Input frequency range PM500, See Note 3 47Hz to 400Hz

VM500 47Hz to 63Hz

Safety ground Less than 3.5mA

leakage current @ 50Hz

GENERAL SPECIFICATIONS

Efficiency 40% typical

Isolation voltage PM series, no suffix 700VAC

PM series, suffix D 2500VAC

PM series, suffix K 2500VAC

VM534D 3000VAC

Switching frequency Linear

Approvals and Safety VM534D IEC950

standards Safety PM5xx

CSA22.2-143/-154, UL478

Case material Non-conductive

black plastic

Weight Case A 181g (6.4oz)

Case B1 (incl. VM534D) 340g (12oz)

Case B2 408g (14.4oz)

Case B3 635g (22.4oz)

Case H 227g (8oz)

MTBF See Note 4 710,000 hours

ENVIRONMENTAL SPECIFICATIONS

Thermal performance Operating amb. –25°C to +71°C

Non-operating amb. –25°C to +85°C

Derating, 50°C to 71°C 2.5%/°C

Cooling Free-air convection

Relative Humidity Non-condensing 20% to 95% RH

Vibration Encapsulated

Recommended for new design-ins

PM500 and VM500 SERIES

Single, dual and triple output

[ 2 YEAR WARRANTY ]

• OVP on 5V outputs

• Split bobbin wound

• PCB mounting

• UL and CSA approved

• 115, 220 and 240VAC input

• Short circuit protection

• The VM500 Series has EN60950 approval

These encapsulated, PC-mountable linear power modules feature 23 single

output, 14 dual output and 13 triple output models for a wide variety of printed

circuit board applications. The 5V output of all models have overvoltage

crowbar protection as a standard feature. For maximum safety, all power

transformers are split bobbin wound, rather than layer wound, to give total

isolation with low coupling capacitance between primary and secondary.

Conservative design and rating of these modules results in reliable operation

and long life. Standard input voltage is 115VAC; other optional inputs are 220

and 240VAC. Most models are available in standard and alternate pin

configurations for second sourcing applications. This series includes 5 sub-

miniature modules for lower power applications where minimum circuit board

space is available.

SPECIFICATION

All specifications are typical at nominal input, full load at 25°C unless otherwise stated

PAGE 1

OUTPUT OUTPUT OVP REGULATION RIPPLE AND CASE AVAILABLE MODELS

VOLTAGE CURRENT LINE LOAD NOISE 110VAC 220VAC 240VAC

SINGLE OUTPUT

5VDC 250mA Yes ±0.02% ±0.04% 1mV rms B1 PM533D

5VDC 500mA Yes ±0.02% ±0.04% 1mV rms B1 PM534 PM534D PM534K

5VDC 500mA Yes ±0.02% ±0.04% 2.8mV rms B1 VM534D

5VDC 1000mA Yes ±0.02% ±0.04% 1mV rms B2 PM542 PM542D PM542K

5VDC 2000mA Yes ±0.02% ±0.05% 1mV rms B3 PM545 PM545D PM545K

12VDC 240mA No ±0.02% ±0.02% 0.5mV rms B2 PM515 PM515D

12VDC 400mA No ±0.02% ±0.02% 1mV rms B3 PM516D

12VDC 600mA No ±0.02% ±0.02% 1mV rms B3 PM517D

24VDC 100mA No ±0.02% ±0.02% 0.5mV rms B2 PM566D

24VDC 200mA No ±0.02% ±0.02% 0.5mV rms B3 PM567D

24VDC 400mA No ±0.02% ±0.02% 1mV rms B3 PM568D

SUB MINIATURE SINGLE OUTPUT SERIES (1)

5VDC 250mA No ±0.05% ±0.05% 0.5mV rms H PM529 PM529D PM529K

12VDC 100mA No ±0.02% ±0.02% 0.5mV rms A PM563 PM563D

DUAL OUTPUT

±12VDC ±120mA No ±0.02% ±0.02% 0.5mV rms B1 PM536 PM536D

±12VDC ±240mA No ±0.02% ±0.02% 0.5mV rms B2 PM537D

±12VDC ±400mA No ±0.02% ±0.02% 0.5mV rms B3 PM597 PM597D PM597K

±15VDC ±25mA No ±0.20% ±0.20% 2mV rms B1 PM538

±15VDC ±100mA No ±0.02% ±0.02% 0.5mV rms B1 PM505 PM505D

±15VDC ±200mA No ±0.02% ±0.02% 0.5mV rms B2 PM565 PM565D

±15VDC ±350mA No ±0.02% ±0.02% 1mV rms B3 PM501 PM501D PM501K

TRIPLE OUTPUT (2)

5V/±12VDC 300/±180mA No ±0.02% ±.05%/±.02% 0.5mV rms B2 PM595S PM595DS

5V/±12VDC 500/±120mA No ±0.02% ±.05%/±.02% 0.5mV rms B2 PM591D

5V/±12VDC 1000/±150mA Yes ±0.02% ±.01%/±.02% 1.0/0.5mV rms B3 PM592 PM592D

5V/±15VDC 300/±150mA Yes ±0.05% ±.10%/±.05% 0.5mV rms B2 PM594 PM594DS

5V/±15VDC 500/±100mA Yes ±0.05% ±.10%/±.05% 0.5mV rms B2 PM590 PM590D PM590K

5V/±15VDC 1000/±150mA Yes ±0.02% ±.01%/±.02% 1.0/0.5mV rms B3 PM593 PM593D PM593K

Notes

1 Trim connection on all sub-miniature series modules provides a means of

externally adjusting a units output voltage precisely to its labelled value. To

raise the output voltage, connect a resistance (20kΩ, min.) between the

trim terminal and the positive (+) output terminal. To lower the output

voltage, connect a resistance (20kΩ, min.) between the trim terminal and

the negative (–) output terminal.

2 Triple output models only: on standard pin-out models the 5V output

common is isolated from the ±12VDC or ±15VDC common.

3 Some units should be derated for operation at 400Hz. Please contact the

factory for details.

4 M.T.B.F. figures are based on actual product performance. Consult factory

for details.

5 All models are only for inclusion by professional installers within other

equipment and must not be operated as a stand alone product.

ALL DIMENSIONS IN INCHES (mm)

SINGLE OUTPUT MODEL

0.50 (12.7)

AC AC

2.20

(55.9)

1.60

(40.6)

3.50

(88.9)

INSERTS

4.40 THREAD

0.125 (3.2) DEEP

0.15

(3.8)

2.50

(63.5)

- OUT OUT

0.60 (15.2)

0.20

(5.1)

MIN.

0.50 (12.7)

0.60 (15.2)

1.60

(40.6)

0.88

(22.4)

0.040 (1.0)

DIA. PINS

CASE

VM534D

1 to 10.5 Watt

AC/DC encapsulated modules

AC/DC POWER SUPPLIES |

1.0-10.5W AC

PAGE 2

http://www.artesyn.com

1.75

(44.5)

TRIM

0.80

(20.3)

1.80

(45.7)

INSERT

4.40 THREAD

0.12 (3.0) DEEP

– OUT OUT +

0.60

(15.2)

0.275

(7.1)

0.20 (5.1)

0.40

(10.2)

1.55

(39.4)

0.20

(5.1)

ALL DIMENSIONS IN INCHES (mm)

0.040 (1.0)

DIA. PINS

0.20

(5.1)

MIN.

2.00

(50.8)

TRIM

0.20

(5.1)

3.00

(76.2)

2.60

(66.0)

INSERT

4.40 THREAD

0.12 (3.0) DEEP

– OUT + OUT

1.60

(40.6)

1.00

(25.4)

0.040 (1.0) DIA. PINS

2.25

(57.2)

1.20

(30.5)

(20K

MIN.)

(20K

MIN.)

– OUT + OUT

TRIM

SUB-MINIATURE

SERIES

0.50 (12.7)

2.20

(55.9)

1.60

(40.6)

3.50

(88.9)

INSERT

4.40 THREAD

0.125 (3.2) DEEP

0.15

(3.8)

2.50

(63.5)

- OUT OUT

0.60 (15.2)

0.20

(5.1)

MIN.

0.50 (12.7)

0.60 (15.2)

1.60

(40.6)

1.62

(41.1)

0.88

(22.4)

0.040 (1.0)

DIA. PINS

B1 B2 B3

1.25

(31.8)

0.50 (12.7)

0.20

(5.1)

MIN.

1.00

(25.4)

CASE A CASE H CASE B

2.00

(50.8)

ALL DIMENSIONS IN INCHES (mm)

CASE B

DUAL OUTPUT

MODELS

0.50 (12.7)

- OUT

COM

+ OUT

0.60 (15.2)

AC AC

2.20

(55.9)

1.60

(40.6)

3.50

(88.9)

0.15

(3.8)

2.50

(63.5)

1.60

(40.6)

0.50 (12.7)

0.60 (15.2)

INSERTS

4.40 THREAD

0.125 (3.2) DEEP

2.20

(55.9)

+ 5V

COM

COM 5V

COM

+ 5V

0.50 (12.7)

0.60 (15.2)

AC AC

1.60

(40.6)

3.50

(88.9)

0.15

(3.8)

2.50

(63.5)

1.60

(40.6)

0.50 (12.7)

0.60 (15.2)

INSERTS

4.40 THREAD

0.125 (3.2) DEEP

0.55 (14.0)

AC AC

1.60

(40.6)

3.50

(88.9)

0.15

(3.8)

2.50

(63.5)

1.60

(40.6)

0.55 (14.0)

INSERTS

4.40 THREAD

0.125 (3.2) DEEP

1.62

(41.1)

0.040 (1.0)

DIA. PINS

B1 B2 B3

1.25

(31.8)

0.88

(22.4)

0.20

(5.1)

MIN.

CASE B

TRIPLE OUTPUT MODELS

STANDARD PINOUT

SIDE VIEW

CASE B

TRIPLE OUTPUT MODELS

ALTERNATE PINOUT SUFFIX '-S'

Single output PM500 series

Dual and triple output PM500 series

International Safety Standard Approvals

IEC950 Certificate No. IDP080 (VM534D only)

UL478 Reg. File No. E131987

CSA22.2-143 and -154 Reg. File No. LR59996

1 to 10.5 Watt

AC/DC encapsulated modules

AC/DC POWER SUPPLIES |

1.0-10.5W AC

PAGE 3