IMCSN
Medium Wall Heat Shrink Tubing
Product Description
3MIMCSN Medium Wall Heat Shrink Tubing is
designed to provide reliable performance for electrical
splices, connections, and terminations, as well as
mechanical and environmental protection. IMCSN is
fabricated from cross-linked polyolefin. The tubing is
highly split resistant, and fast-shrinking to provide
rapid installation. The tubing comes standard with a
factory-applied adhesive/sealant.
Product Features
Fast and easy installation
Resists puncture and abrasion damage
Complete environmental protection
Versatile, a minimum number of sizes cover the
entire range of applications
Shrink ratio 3:1
Resists acids and alkalies
Bonds to a wide variety of substrates
Reliable and proven
UV resistant
Applications
Primary electrical insulation for solid dielectric
wire and cable rated to 1000 volts
For indoor, outdoor or overhead use
Direct buried or submersible
Insulating secondary splices
Physical protection and moisture sealing of high
voltage air insulated connectors and lugs, such as
lug connections to bus bars
Relocation of service
Dig-in repairs
Product Selection
Selecting 3M IMCSN tubing is easy and
straightforward. The largest tubing that provides a
tight fit when fully recovered will produce the
maximum wall thickness. Final wall thickness is
proportional to the degree of tubing recovery.
Physical and Electrical Typical Properties
Property Requirement* Test Results
Continuous Operating -55°C to 110°C -55°C to 110°C
Temperature Range
Color Black Black
Longitudinal Change + 1%, - 10% Pass
Low Temperature Flexibility No Cracking Pass
(4 hours @ -55°C)
Heat Shock No Cracking, Flowing Pass
(4 hours @ 255°C) or Dripping
2% Secant Modulus 25,000 psi min. 14,000psi
Color Stability Remain Stable Pass
(24 hours @ 175°C)
Tensile Strength 1,200 psi min. 2,400 psi
Ultimate Elongation 200% min. 475%
Dielectric Strength (V/ mil) 200 min. 5 0 0
Volume Resistivity (ohm-cm) 1 01 3 m i n . 1 01 4
* Based on MIL-I-23053/15A Class 2
Fluid Resistance / MIL-I-23053
Minimum tensile strength, 750 psi
Minimum dielectric strength, 200 V/mil
Twenty-four hours at 25°C
Fluids Tensile Strength Dielectric Strength
Hydraulic Fluid Pass Pass
JP-4 Fuel Pass Pass
Lube Oil Pass Pass
5% NaCl Solution Pass Pass
Deicing Fluid Pass Pass
Engineering/Architectural Specifications
The tubing must be usable both indoors and outdoors,
in overhead, direct-buried, or submerged applications
on cables rated up to 1000 volts. It is not adversely
affected by moisture, mild acids and alkalies, fuels,
oils, ozone, or ultraviolet light. It must be compatible
with and adhere to all types of cable jackets, including
rubber, plastic, or lead. It must conform to the
requirements of UL 486 D and sections 3.4 and 4.3 of
ANSI C119.1 1986.
3MIMCSN Selection Chart
Product Cable Size Minimum Expanded / Cable O.D. Use Range
Number Range Maximum Recovered I.D. Maximum - Minimum
IMCSN-0400-48A 12 - 6 AWG (4 - 10 mm2) 0.40 / 0.15” 10,2 / 3,8 mm 0.35 - 0.15” 8,8 - 3,8 mm
IMCSN-0800-48A 8 - 3AWG (10 - 25 mm2)0.80 / 0.22” 20,3 / 5,6 mm 0.70 - 0.22” 18 - 5,6 mm
IMCSN-1100-48A 2 - 2/0AWG (35 - 60 mm2)1.10 / 0.37” 27,9 / 9,4 mm 0.95 - 0.37” 24 - 9,4 mm
IMCSN-1300-48A 1 - 4/0AWG (50 - 100 mm2)1.30 / 0.43” 33,0 / 10,9 mm 1.10 - 0.43” 28 - 10,8 mm
IMCSN-1500-48A 1/0 - 250 kcmil (60 - 120 mm2) 1.50 / 0.50” 38,1 / 12,7 mm 1.30 - 0.50” 33 - 12,1 mm
IMCSN-1700-48A 4/0 - 400kcmil (120 - 200 mm2)1.70 / 0.60” 43,2 / 15,2 mm 1.45 - 0.60” 37 - 15,2 mm
IMCSN-2000-48A 300 - 500kcmil (185 - 250 mm2)2.00 / 0.75” 50,8 / 19,1 mm 1.75 - 0.75” 44,5 - 19,0 mm
IMCSN-3000-48A 600 - 1250 kcmil (325 - 625 mm2) 3.00 / 1.00” 76,2 / 25,4 mm 2.50 - 1.00” 63,5 - 25,4 mm
IMCSN-4300-48A 1000 - 2500 kcmil (625 - 1000 mm2) 4.30 / 1.16” 109,2 / 38,1 mm 3.60 - 1.50” 91,5 - 38,1 mm
Note: 3M IMCSN is supplied in 48-inch lengths with adhesive. Uncoated products available on special order.
Installation Techniques
Exact instructions are available on a separate sheet.
The following is a summary of the instructions.
1. Thoroughly clean and prepare cable.
2. Cut 3M IMCSN to required size, per instructions.
3. Slide 3M IMCSN tubing onto cable.
4. Install connector, if applicable.
5. Center tubing.
Property Requirement * Test Results
Corrosion
(16 hours @ 121°C)
– Copper Mirror No corrosion Pass
– Copper Contact No corrosion or pitting Pass
Flammability
(Five 15-second Bunsen
burner applications) Nonburning Pass
Water Absorption 0.5% Maximum 0.02%
(24 hours @ 25°C) weight increase
Heat Aging
(7 days @175°C)
– Ultimate Elongation 100% Minimum 225%
– Tensile Strength 1000 psi Minimum 1820 PSI
Fungus Resistance Non-nutrient Pass
Shelf Life Storage @ 40°C for 2 years
with maintenance of dimensions Pass
Performance Tests
Meets MIL-I-23053/15A Class 2.
* Based on MIL-!-23053/15AClass 2
Maintenance
3M IMCSN medium wall heat shrinkable tubing is not
impaired by freezing or overheating due to ambient
temperature found in storage or shipping. Normal
storage and stock rotation are recommended.
Availability
3M IMCSN medium wall heat shrink tubing is
available from your electrical distributor.
6. Shrink tubing from center.
7. Heat until tubing is completely shrunk and
adhesive/sealant (if applicable) is squeezed from ends.
All statements, technical information, and recommendations related
to Seller’s products are based on information believed to be reliable,
but the accuracy or completeness thereof is not guaranteed. Before
utilizing the product, the user should determine the suitability of the
product for its intended use. The user assumes all risks and liability
whatsoever in connection with such use.
Any statements or recommendations of the Seller which are not
contained in the Seller’s current publications shall have no force or
effect unless contained in an agreement signed by an authorized
officer of Seller. The statements contained herein are made in lieu of
all warranties, expressed or implied, including but not limited to the
implied warranties of merchantability and fitness for a particular
purpose which warranties are hereby expressly disclaimed.
SELLER SHALLNOTBE LIABLE TO THE USER OR ANY OTHER
PERSON UNDER ANYLEGALTHEORY, INCLUDING BUTNOT
LIMITED TO NEGLIGENCE OR STRICTLIABILITY, FOR ANY
INJURYOR FOR ANY DIRECT, INDIRECT, INCIDENTAL, OR
CONSEQUENTIALDAMAGES SUSTAINED OR INCURRED BY
REASON OF THE USE OF ANYOF THE SELLER’S PRODUCTS.
Important Notice
Litho in USA.
© 3M 1997 80-6111-0069-6
Electrical Products Division
6801 River Place Blvd.
Austin, TX 78726-9000
800/328-1368 40% Pre-consumer waste paper
10% Post-consumer waste paper
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
3M:
IMCSN-1100-48A IMCSN-1700-48A IMCSN-1500-25-U IMCSN-3000-25-U IMCSN-4300-48A IMCSN-0400-25-U
IMCSN-0800-48A IMCSN-4300-25-U IMCSN-0800-25-U IMCSN-1300-48A IMCSN-0400-48A IMCSN-1700-25-U
IMCSN-2000-25-U IMCSN-3000-48A IMCSN-2000-48A IMCSN-1500-48A IMCSN-1100-25-U