Agilent HFBR-4531/4532/4533/4535 Crimpless Connectors for Plastic Optical Fiber and Versatile Link Data Sheet Description The HFBR-453x series connectors are an enhanced version of the HFBR-4501 and HFBR-4503 low-cost connectors for plastic optical fiber, which are compatible with Agilent's versatile link series transmitters and receivers. The innovative design uses a simple, snaptogether concept which eliminates the need for crimping. This connector not only saves the user labor and tool cost, but reduces the yield loss due to installation error. The HFBR-453x series connectors are available in two styles: latching and non-latching. For a duplex connector, two non-latching simplex connectors can be snapped together. The connectors are made of a rugged, flame retardant plastic which is good for industrial and other harsh environments. The HFBR-453x series connectors are for use with Plastic Optical Fiber only. Features * Requires No Crimp Ring or Crimping Tool * Durable ULTEM(R) Plastic Material (UL File #E121562) * Same Low Cost as HFBR-4501/ 4503 Series Connectors * Excellent Retention Force * Symmetry in Nonlatching Connector Gives Simplex/Duplex Functionality with the Same Part The HFBR-453x Series of connectors are available in three colors; black, blue and grey. The ability to select colors to match Transmitters and Receivers makes it easier for the User to differentiate between fiber connections especially when there are a large number. ULTEM(R) is a registered trademark of the General Electric Corporation. Applications These connectors can be used for any application in which plastic optical fiber is used including: * Industrial Control and Voltage Isolation * Automotive Networks * Proprietary System Interconnects * Gaming Equipment * Medical Equipment * Telecommunications * Datacommunications Termination Guide Step-by-Step Plastic Cable Connectoring Instructions The following step-by-step guide describes how to terminate plastic fiber optic cable. It is ideal for both field and factory installations. Connectors can be easily installed on cable ends with standard tools such as wire strippers and cutters. Finishing the cable is accomplished with the Agilent HFBR-4593 Polishing Kit, consisting of a polishing fixture, 600 grid abrasive paper and 3 mm pink lapping film (3M Company, OC3-14). The connector can be used immediately after polishing. The following materials are needed for plastic fiber termination: To install simplex connectors flip the top half of the connector over and snap it into the ferrule half (with your fingers). When the top half latches inside the body of the ferrule half, proper connector-to-cable attachment is achieved. When using the duplex connector arrangement, the separated duplex cable should be stripped to roughly equal lengths on each cable end. For the non-latching version (HFBR-4531), the same connector is used for simplex and duplex arrangement. No crimping is necessary. The top half of the connector will snap into the ferrule half to secure the fiber. Manually press connectors together in the center of the arrangement. Then latch by pressing on the sides of each connector. As with the simplex version, connectors are secured when top halves latch into the ferrule halves. 1. Plastic optical fiber cable (Example: HFBR-RUD500) 2. Wire cutters or scissors 3. 16 gauge wire stripper (Example: Ideal Stripmaster type 45-092) 4. HFBR-4593 polishing kit (optional) 5. Crimpless connectors Step 1: Stripping the Fiber The zip cord structure of the duplex cable permits easy separation of the channels. The channels should be separated a minimum of 100 mm (4 in) to a maximum of 150 mm (6 in) back from the ends to permit connectoring, polishing and cable end flexibility. After cutting the cable to the desired length, strip off approximately 7 mm (0.3 in) of the outer jacket with the 16 gauge wire strippers. 2 For duplex connector installation place one connector on top of the other, so that the top half of each connector is over the ferrule half of the opposite connector. Step 2: Putting on the Connector Place the connector on each end of the fiber, and slide the connector down until the fiber jacket stops it. The fiber should protrude no less than 1.5 mm (0.06 in) from the end of the connector. Step 3: Trimming and Polishing Any fiber in excess of 1.5 mm (0.06 in) protruding from the connector end should be cut off with wire cutters or scissors. Insert the connector fully into the polishing fixture with the trimmed fiber protruding from the bottom of the fixture. This plastic polishing fixture can be used to polish two simplex connectors simultaneously or one duplex connector. Step 4: Finishing Place the flush connector and polishing fixture on the dull side of the 3 m pink lapping film and continue to polish the fiber in the same figure eight pattern for approximately 25 strokes. The fiber end should be flat, smooth and clean. Note: The four dots on the bottom of the polishing fixture are wear indicators. Replace the polishing fixture when any dot is no longer visible. Press the polishing tool down on the 600 grit abrasive paper. Polish the fiber using a figure eight pattern until the connector is flush with the bottom of the polishing fixture. Wipe the connector and fixture with a clean cloth or tissue. 3 HFBR-4593 Polishing Kit Note: Use of the pink lapping film fine polishing step results in approximately 2 dB improvement in coupling performance of either a transmitter-receiver link or a bulkhead/splice over a 600 grit polish alone. This fine polish is comparable to the Agilent factory polish. The fine polishing step may be omitted for short link lengths. Crimpless Connectors Simplex Non-Latching Latching Black HFBR-4531 HFBR-4532 Blue HFBR-4533 NA Grey HFBR-4535 NA HFBR-4531/4532/4533/4535 Absolute Maximum Ratings Parameter Symbol Min Max Units Note Storage Temperature TS -40 +85 C 1 Operating Temperature TO -40 +85 C 1 Installation Temperature TI 0 +70 C 1 Connector Mechanical Characteristics Parameter Part Number Symbol Min Typ Units Temp C Retention Force to HFBR-0501 Series HFBR-4531 FR-C 3 8 N +25 HFBR-4532 47 80 Retention Force to HFBR-0508 Series HFBR-4531 8 12 Tensile Force, Connector to Cable HFBR-4531 40 50 FT -40 to +85 HFBR-4532 Note: 1. Storage and operating temperatures refer to the ranges over which the connectors can be used when not subjected to mechanical stress. Installation temperature refers to the ranges over which connectors may be installed onto the fiber and over which connectors can be connected and disconnected from the transmitter and receiver modules. Mechanical Dimensions All dimensions are in inches and (millimeters). HFBR-4531 (Nonlatching): 1.18 (29.97) 0.72 (18.29) 0.37 (9.39) 0.0874 (2.22) 0.24 (6.10) 4 0.15 (3.81) HFBR-4532 (Latching): 1.07 (27.18) 0.20 (5.08) 0.37 (9.39) 0.97 (24.71) 0.29 (7.32) 0.15 (3.81) 0.09 (2.22) 0.35 (8.89) 0.20 (4.95) 0.24 (6.10) HFBR-4531 in Duplex Configuration 1.18 (29.97) 0.72 (18.29) 0.357 (9.07) 0.0874 (2.22) 0.15 (3.81) 0.0874 (2.22) 0.15 (3.81) 0.758 (19.25) 0.357 (9.07) 5 www.agilent.com/ semiconductors For product information and a complete list of distributors, please go to our web site. For technical assistance call: Americas/Canada: +1 (800) 235-0312 or (916) 788-6763 Europe: +49 (0) 6441 92460 China: 10800 650 0017 Hong Kong: (+65) 6756 2394 India, Australia, New Zealand: (+65) 6755 1939 Japan: (+81 3) 3335-8152(Domestic/International), or 0120-61-1280(Domestic Only) Korea: (+65) 6755 1989 Singapore, Malaysia, Vietnam, Thailand, Philippines, Indonesia: (+65) 6755 2044 Taiwan: (+65) 6755 1843 Data subject to change. Copyright (c) 2003 Agilent Technologies, Inc. Obsoletes: 5965-1659E June 19, 2003 5988-9777EN