General Description
The MAX889 inverting charge pump delivers a regulated
negative output voltage at loads of up to 200mA. The
device operates with inputs from 2.7V to 5.5V to produce
an adjustable, regulated output from -2.5V to -VIN.
The MAX889 is available with an operating frequency of
2MHz (T version), 1MHz (S version), or 0.5MHz (R ver-
sion). The higher switching frequency devices allow the
use of smaller capacitors for space-limited applica-
tions. The lower frequency devices have lower quies-
cent current.
The MAX889 also features a 0.1µA logic-controlled
shutdown mode and is available in an 8-pin SO pack-
age. An evaluation kit, MAX889SEVKIT, is available.
________________________Applications
TFT Panels
Hard Disk Drives
Camcorders
Digital Cameras
Measurement Instruments
Battery-Powered Applications
Features
200mA Output Current
Up to 2MHz Switching Frequency
Small Capacitors (1µF)
+2.7V to +5.5V Input Voltage Range
Adjustable Regulated Negative Output
(-2.5V to -VIN)
0.1µA Logic-Controlled Shutdown
Low 0.05Output Resistance (in regulation)
Soft-Start and Foldback Current Limited
Short-Circuit and Thermal Shutdown Protected
8-Pin SO Package
MAX889
High-Frequency, Regulated,
200mA, Inverting Charge Pump
________________________________________________________________ Maxim Integrated Products 1
SHDN
OUTCAP-
1
2
8
7
AGND
FBCAP+
GND
IN
SO
TOP VIEW
3
4
6
5
MAX889
Pin Configuration
MAX889
IN
INPUT +2.7V TO +5.5V
REGULATED
NEGATIVE
OUTPUT
(UP TO -1 × VIN,
UP TO 200mA)
FB
OUT
GNDAGND
CAP+
ON
OFF SHDN
CAP-
Typical Operating Circuit
19-1774; Rev 0; 7/00
For free samples and the latest literature, visit www.maxim-ic.com or phone 1-800-998-8800.
For small orders, phone 1-800-835-8769.
Ordering Information
PART
TEMP.
RANGE
PIN-
PACKAGE
SWITCHING
FREQUENCY
MAX889TESA -40°C to +85°C
8 SO 2MHz
MAX889SESA -40°C to +85°C
8 SO 1MHz
MAX889RESA -40°C to +85°C
8 SO 0.5MHz
EVALUATION KIT
AVAILABLE
MAX889
High-Frequency, Regulated,
200mA, Inverting Charge Pump
2 _______________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS
(VIN = VSHDN = +5V, capacitors from Table 1, TA= 0°C to +85°C, unless otherwise noted. Typical values are at TA= +25°C.)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
IN to GND .................................................................-0.3V to +6V
FB, SHDN, CAP+ to GND............................-0.3V to (VIN + 0.3V)
AGND to GND .......................................................-0.3V to +0.3V
OUT to GND .............................................................-6V to +0.3V
CAP- to GND ............................................(VOUT - 0.3V) to +0.3V
Continuous Output Current ...............................................250mA
Output Short-Circuit Duration ........................................Indefinite
Continuous Power Dissipation (TA= +70°C)
8-Pin SO (derate 5.88mW/°C above +70°C)...............471mW
Operating Temperature Range...........................-40°C to +85°C
Junction Temperature......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) ................................+300°C
PARAMETER
SYMBOL
CONDITIONS
MIN TYP MAX UNITS
Supply Voltage Range VIN RLOAD = 1002.7
5.5
V
Output Voltage Range VOUT R LOAD = 100
-2.5 -VIN
V
IOUT(MAX)1
VIN = 5V, VOUT = -3.3V
200
Maximum Output Current
IOUT(MAX)2
VIN = 3.3V, VOUT = -2.5V
145
mA
MAX889R 6 12
MAX889S 12 24
Quiescent Supply
Current (Free-Run Mode)
IQ
(
FREE-RUN
)
No load, VFB = VIN
MAX889T 24 48
mA
MAX889R 3.3 7
MAX889S 5.5 12
Quiescent Supply
Current (Regulated Mode)
IQ
(
REGULATED
)
No load, VOUT regulated to
-3.3V MAX889T 11 22
mA
Shutdown Supply Current I
SHDN V
SHDN = 0 0.1 50 µA
Open-Loop Output
Resistance (Free-Run Mode) ROVFB = VIN 2.0
4.5
Output Resistance RO(REG1) VOUT regulated to -3.3V
0.05
SHDN, FB Input Bias Current ±1µA
FB Input Offset Voltage ILOAD = 0 ±3
±35
mV
Load Regulation IOUT = 0 to 200mA 10 mV
IN Undervoltage Lockout
Threshold VIN rising (30mV hysteresis) 2.3
2.6
V
SHDN Logic High VIH
0.7 x VIN
SHDN Logic Low VIL
VIN = +2.7V to +5.5V
0.3 x VIN
V
MAX889R
0.375
0.5 0.62
MAX889S
0.75
1
1.25
Switching Frequency fOSC
MAX889T 1.5 2
2.5
MHz
Thermal Shutdown Threshold Junction temperature rising
(15°C hysteresis) 160 °C
MAX889
High-Frequency, Regulated,
200mA, Inverting Charge Pump
_______________________________________________________________________________________ 3
Note 1: Specifications to -40°C are guaranteed by design, not production tested.
ELECTRICAL CHARACTERISTICS
(VIN = VSHDN = +5V, capacitors from Table 1, TA= -40°C to +85°C, unless otherwise noted.) (Note 1)
PARAMETER
SYMBOL
CONDITIONS
MIN MAX
UNITS
Supply Voltage Range VIN RLOAD = 1002.7
5.5
V
Output Voltage Range VOUT R LOAD = 100
-2.5 -VIN
V
IOUT(MAX)1
VIN = 5V, VOUT = -3.3V
200
Maximum Output Current
IOUT(MAX)2
VIN = 3.3V, VOUT = -2.5V
145
mA
MAX889R 12
MAX889S 24
Quiescent Supply
Current (Free-Run Mode)
IQ
(
FREE-RUN
)
No load, VFB = VIN
MAX889T 48
mA
MAX889R 7
MAX889S 12
Quiescent Supply
Current (Regulated Mode)
IQ
(
REGULATED
)
No load, VOUT regulated to
-3.3V
MAX889T 22
mA
Shutdown Supply Current I
SHDN V
SHDN = 0 50 µA
Open-Loop Output
Resistance (Free-Run Mode) ROVFB = VIN
4.5
SHDN FB Input Bias Current ±1µA
FB Input Offset Voltage ILOAD = 0
±35
mV
IN Undervoltage Lockout
Threshold VIN rising (30mV hysteresis) 2.3
2.6
V
SHDN Logic High VIH
0.7 x V IN
SHDN Logic Low VIL
VIN = +2.7V to +5.5V
0.3 x VIN
V
MAX889R
0.375
0.62
MAX889S
0.75 1.25
Switching Frequency fOSC
MAX889T 1.5
2.5
MHz
Typical Operating Characteristics
(Circuit of Figure 1, VIN = VSHDN = +5V, capacitors from Table 1, TA= +25°C, unless otherwise noted.)
OUTPUT VOLTAGE
vs. LOAD CURRENT
MAX889 toc01
OUTPUT LOAD CURRENT (mA)
OUTPUT VOLTAGE (V)
-3.33
-3.32
-3.31
-3.30
-3.29
-3.28
-3.27
-3.26
-3.25
0 200 400 600 800
MAX889T
MAX889S
MAX889R
0
10
20
30
40
MAX889R
OUTPUT RIPPLE
vs. LOAD CURRENT vs. COUT
MAX889 toc02
LOAD CURRENT (mA)
OUTPUT RIPPLE (mV)
0 150 20050 100 250 300 350
COUT = 22µF
COUT = 47µF
COUT = 10µF
0
10
20
30
40
MAX889S
OUTPUT RIPPLE
vs. LOAD CURRENT vs. COUT
MAX889 toc03
LOAD CURRENT (mA)
OUTPUT RIPPLE (mV)
0 150 20050 100 250 300 350
COUT = 4.7µF
COUT = 22µF
COUT = 10µF
MAX889
High-Frequency, Regulated,
200mA, Inverting Charge Pump
4 _______________________________________________________________________________________
0
10
30
20
40
50
0 10050 150 200 250 300 350
MAX889T
OUTPUT RIPPLE
vs. LOAD CURRENT vs. COUT
MAX889 toc04
LOAD CURRENT (mA)
OUTPUT RIPPLE (mV)
COUT = 2.2µF
COUT = 4.7µF
COUT = 10µF
0
30
20
10
40
50
60
70
80
90
100
0200100 300 400 500
EFFICIENCY vs. LOAD CURRENT
(VIN = 5V, VOUT = -3.3V)
MAX889 toc05
LOAD CURRENT (mA)
EFFICIENCY (%)
MAX889T
MAX889R
MAX889S
0
30
20
10
50
40
90
80
70
60
100
0 50 100 150 200 250 300 350
EFFICIENCY vs. LOAD CURRENT
(VIN = 3.3V, VOUT = -2.5V)
MAX889 toc06
LOAD CURRENT (mA)
EFFICENCY (%)
MAX889R
MAX889T
MAX889S
Typical Operating Characteristics (continued)
(Circuit of Figure 1, VIN = VSHDN = +5V, capacitors from Table 1, TA= +25°C, unless otherwise noted.)
MAX889S
LOAD-TRANSIENT RESPONSE
MAX889 toc10
40µs/div
A
B
20 TO 200mA LOAD STEP
CIRCUIT OF FIGURE 4
A: IOUT, 100mA/div
B: VOUT, 20mV/div, AC-COUPLED
MAX889S
LINE-TRANSIENT RESPONSE
MAX889 toc11
40µs/div
A
B
IOUT = 200mA
CIRCUIT OF FIGURE 4
A: VIN, 2V/div
B: VOUT, 10mV/div, AC-COUPLED
MAX889S
STARTUP AND SHUTDOWN
MAX889 toc12
2ms/div
A
B
IOUT = 200mA
A: VOUT, 1V/div
B: IIN, 100mA/div
C: VSHDN, 10V/div
C
0
0
1.50
2.00
1.75
2.50
2.25
2.75
3.00
2.5 3.5 4.03.0 4.5 5.0 5.5
FREE-RUN OUTPUT RESISTANCE
vs. INPUT VOLTAGE
MAX889 toc07
INPUT VOLTAGE (V)
ROUT ()
1.0
1.5
2.0
2.5
3.0
FREE-RUN OUTPUT RESISTANCE
vs. TEMPERATURE
MAX889 toc08
TEMPERATURE (°C)
ROUT ()
-40 20 40-20 0 60 80
0
4
2
8
6
10
12
2.5 3.5 4.03.0 4.5 5.0 5.5
QUIESCENT SUPPLY CURRENT
vs. INPUT VOLTAGE (REGULATED MODE)
MAX889 toc09
INPUT VOLTAGE (V)
QUIESCENT CURRENT (mA)
MAX889T
MAX889S
MAX889R
VOUT = -2.5V
MAX889
High-Frequency, Regulated,
200mA, Inverting Charge Pump
_______________________________________________________________________________________ 5
Pin Description
Detailed Description
The MAX889 high-current regulated charge-pump DC-
DC inverter provides up to 200mA. It features the high-
est available output current while using small
capacitors (Table 1). The three versions available differ
in their switching frequencies (fOSC)MAX889R/
MAX889S/MAX889T with fOSC = 500kHz/1MHz/2MHz,
respectively. Higher frequencies allow the use of small-
er components (Table 1). Even smaller capacitor values
than those listed in Table 1 are suitable when the
devices are loaded at less than their rated output cur-
rent. Designed specifically for compact applications, a
complete regulating circuit requires only three small
capacitors and two resistors, Figure 1. In addition, the
MAX889 includes soft-start, shutdown control, short-cir-
cuit, and thermal protection.
The oscillator, control circuitry, and four power MOSFET
switches are included on-chip. The charge pump runs
continuously at the operating frequency. During one-half
of the oscillator period, switches S1 and S2 close
(Figure 2), charging the transfer capacitor (CFLY) to the
input voltage (CAP- = GND, CAP+ = IN). During the
other half cycle, switches S3 and S4 close (Figure 3),
transferring the charge on CFLY to the output capacitor
(CAP+ = GND, CAP- = OUT).
Voltage Regulation
Voltage regulation is achieved by controlling the flying-
capacitor charging rate. The MAX889 controls the
charge on CFLY by modulating the gate drive to S1
(Figure 2) to supply the charge necessary to maintain
output regulation. When the output voltage droops,
CFLY charges higher due to increased gate drive. Since
the device switches continuously, the regulation
scheme minimizes output ripple, and the output noise
spectrum contains well-defined frequency components.
Feedback voltage is sensed with a resistor-divider
between an externally supplied positive reference or
the supply voltage and the negative inverted output.
The feedback loop servos FB to GND. The effective
output impedance in regulation is 0.05. The output
remains in regulation until dropout is reached. Dropout
depends on the output voltage setting and load current
(see Output Voltage vs. Load Current in Typical
Operating Characteristics).
Free-Run Mode
(Unregulated Voltage Inverter)
The MAX889 may be used in an unregulated voltage
inverter mode that does not require external feedback
resistors, minimizing board space. Connecting FB to IN
places the MAX889 in free-run mode. In this mode, the
charge pump operates to invert directly the input sup-
ply voltage (VOUT = -(VIN - IOUT x RO)). Output resis-
tance is typically 2and can be approximated by the
following equation:
RO[1 / (fOSC x CFLY) ] + 2RSW +
4ESRCFLY + ESRCOUT
The first term is the effective resistance of an ideal
switched-capacitor circuit (Figures 2 and 3), and RSW
is the sum of the charge pumps internal switch resis-
tances (typically 0.8at VIN = 5V). The last two terms
take into consideration the equivalent series resistance
MAX889
(ESR) of the flying and output capacitors. The typical
output impedance is more accurately determined from
the Typical Operating Characteristics.
Current Limit and Soft-Start
The MAX889 features a foldback current-limit/soft-start
scheme that allows it to limit inrush currents during
startup, overload, and output short-circuit conditions.
Additionally, it permits a safe, timed recovery from fault
conditions. This protects the MAX889 and prevents
low-current or higher output impedance input supplies
(such as alkaline cells) from being overloaded at start-
up or short-circuit conditions.
The MAX889 features two current-limit/soft-start levels
with corresponding response to rising and falling out-
put voltage thresholds of -0.6V and -1.5V. When the
falling output voltage crosses -1.5V, such as during an
overload condition, the input current is immediately lim-
ited to 400mA by weakening the charge-pump switch-
es. When the falling output voltage crosses -0.6V, such
as during a short-circuit condition, the MAX889 further
weakens the charge-pump switches, immediately limit-
ing input current to 200mA.
During startup or short-circuit recovery, the MAX889
limits input current to 200mA with charge-pump switch-
es at their weakest level. Rising output voltage crossing
-0.6V initiates a 2ms timer, after which the MAX889
increases switch strength to the next level. The rising
output voltage crossing -1.5V initiates a 2ms timer, after
which the MAX889 provides full-strength operation.
Shutdown
When SHDN (a CMOS-compatible input) is driven low,
the MAX889 enters 0.1µA shutdown mode. Charge-
pump switching halts. Connect SHDN to IN or drive
high for normal operation.
Thermal Shutdown
The MAX889 features thermal shutdown with hysteresis
for added protection against fault conditions. When the
die temperature exceeds 160°C, the internal oscillator
stops, suspending device operation. The MAX889
resumes operation when the die temperature falls 15°C.
This prevents the device from rapidly oscillating around
the temperature trip point.
Applications Information
Resistor Selection
(Setting the Output Voltage)
The accuracy of VOUT depends on the accuracy of the
voltage biasing R1 in Figure 1. Use a separate refer-
ence voltage if greater accuracy than provided by VIN
is desired (Figure 4). Keep the feedback node as small
as possible, with resistors mounted close to the FB pin.
High-Frequency, Regulated,
200mA, Inverting Charge Pump
6 _______________________________________________________________________________________
Figure 1. Typical Application Circuit.
MAX889T
IN
INPUT
5.0V
OUTPUT
-3.3V
CIN
4.7µF
COUT
4.7µF
CFLY
1µF
FB
R1
100k
R1
66.5k
OUT
GND
CAP+
ON
OFF
4
2
3
SHDN
CAP-
1
7
5
6
8
Figure 3. Transferring Charge on CFLY to COUT
S2
OUT
COUT
CFLY
S1
IN
S4
S3
FOSC
CAP+
CAP-
Figure 2. Charging CFLY
S2
OUT
COUT
CFLY
S1 CAP+
CAP-
IN
S4
S3
FOSC
MAX889
High-Frequency, Regulated,
200mA, Inverting Charge Pump
_______________________________________________________________________________________ 7
Adjust the output voltage to a negative voltage from
-2.5V to -VIN with external resistors R1 and R2 as
shown in Figures 1 and 4. FB servos to GND. Choose
R1 to be 100kor less. Calculate R2 for the desired
output voltage:
VOUT = -VREF (R2 / R1)
R2 = R1 (VOUT / -VREF)
where VREF can be either VIN or a positive reference
source.
Typically, choose a voltage-divider current of at least
30µA to minimize the effect of FB input current and
capacitance:
R1 VREF / 30µA
R2 < -VOUT / 30µA
Capacitor Selection
The appropriate capacitors used with the MAX889
depend on the switching frequency. Table 1 provides
suggested values for CIN, CFLY, and COUT.
Surface-mount ceramic capacitors are preferred for
CIN, COUT, and CFLY due to their small size, low cost,
and low ESR. To ensure proper operation over the
entire temperature range, choose ceramic capacitors
with X7R (or equivalent) low-temperature-coefficient
(tempco) dielectrics. See Table 2 for a list of suggested
capacitor suppliers.
The output capacitor stores the charge transferred from
the flying capacitor and services the load between
oscillator cycles. A good general rule is to make the
output capacitance at least five-times greater than the
flying capacitor.
Output voltage ripple is largely dependent on COUT.
Choosing a low-ESR capacitor of sufficient value is impor-
tant in minimizing the peak-to-peak output voltage ripple,
which is approximated by the following equation:
where COUT is the output capacitor value, ESRCOUT is
the output capacitors ESR, and fOSC is the MAX889
switching frequency. Ceramic capacitors have the lowest
ESR and are recommended for COUT. Where larger
capacitance at low cost is desired, a low-ESR tantalum
capacitor may be used for COUT. See Table 2 for a list of
suggested capacitor suppliers.
To ensure stability over the entire operating temperature
range, choose a low-ESR output capacitor using the fol-
lowing equation:
where COUT is the output capacitor value, and fMIN is the
minimum oscillator frequency in the Electrical
Characteristics table.
To ensure stability for regulated output mode, suitable
output capacitor ESR should be determined by the follow-
ing equation:
Power Dissipation
The power dissipated in the MAX889 depends on the
input voltage, output voltage, and output current. Device
power dissipation is accurately described by:
PDISS = IOUT (VIN - (-VOUT)) + (IQVIN)
where IQis the device quiescent current. PDISS must be
less than the package dissipation rating (see Absolute
Maximum Ratings). Pay particular attention to power dis-
sipation limits when generating small negative voltages
from large positive input voltages.
Layout Considerations
The MAX889s high oscillator frequencies demand
good layout techniques that ensure stability and help
maintain the output voltage under heavy loads. Take
the following steps to ensure optimum layout:
1) Mount all components as close together as possible.
2) Place the feedback resistors R1 and R2 close to the
FB pin, and minimize the PC trace length at the FB
circuit node.
3) Keep traces short to minimize parasitic inductance
and capacitance.
4) Use a ground plane with CIN and COUT placed in a
star ground configuration (see the MAX889SEVKIT
layout).
R
19.2 x 10
I
R2
R1
ESR
-3
OUT
+
1
C
15.5
f
R1
R1 + R2 I
OUT MIN
OUT
V = I
2 x f C
2 x I ESR
RIPPLE OUT
OSC OUT
OUT COUT
+
MAX889
High-Frequency, Regulated,
200mA, Inverting Charge Pump
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
8_____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2000 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products.
SOICN.EPS
Table 1. Capacitor Selection Table
PART FREQUENCY CFLY COUT CIN
REGULATED
CIN
FREE-RUN
MAX889R 0.5MHz 4.7µF22µF22µF 4.7µF
MAX889S 1MHz 2.2µF10µF10µF 2.2µF
MAX889T 2MHz 1µF 4.7µF 4.7µF1µF
PRODUCTION
METHOD MANUFACTURER SERIES PHONE FAX
AVX TPS series 803-946-0690 803-626-3123
Kemet 494 series 864-963-6300 864-963-6521
Matsuo 267 series 714-969-2491 714-960-6492
Surface-Mount
Tantalum
Sprague 593D, 595D series 603-224-1961 603-224-1430
S ur face- M ount P ol ym er Sanyo POSCAP-APA 619-661-6835 619-661-1055
AVX X7R 803-946-0690 803-626-3123
Kemet X7R 864-963-6300 864-963-6521
Matsuo X7R 714-969-2491 714-960-6492
S ur face- M ount C er am i c
Murata GRM X7R 814-237-1431 814-238-0490
Table 2. Low-ESR Capacitor Manufacturers
Chip Information
TRANSISTOR COUNT: 1840
PROCESS: BiCMOS
Package Information
Figure 4. Separate VREF for Voltage Divider
MAX889T
IN
INPUT
5.0V
OUTPUT
-3.3V
CIN
4.7µF
COUT
4.7µF
VREF
5V
CFLY
1µF
FB
R1
100k
R2
66.5k
OUT
GNDAGND
CAP+
ON
OFF
4
2
3
SHDN
CAP-
1
7
5
6
8
VOUT = -VREF × R2
R1
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Maxim Integrated:
MAX889RESA+ MAX889SESA+ MAX889TESA+ MAX889RESA+T MAX889SESA+T MAX889TESA+T
MAX889RESA MAX889RESA-T MAX889SESA-T MAX889TESA MAX889TESA-T MAX889SESA