Datasheet
Product structureSilicon monolithic integrated circuitThis product is not designed protection against radioactive rays
.
1/19
TSZ02201-0F2F0A200010-1-2
07.Mar.2017.Rev.006
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ2211114001
www.rohm.com
AC/DC Drivers
PWM type DC/DC converter IC
Included 650V MOSFET
BM2PXX1 Series
General Description
The PWM type DC/DC converter (BM2PXX1) for
AC/DC provide an optimum system for all products
that include an electrical outlet.
BM2PXX1 supports both isolated and non-isolated
devices, enabling simpler design of various types of
low-power electrical converters.
BM2PXX1 built in a HV starter circuit that tolerates
650V, it contributes to low-power consumption.
With current detection resistors as external devices, a
higher degree of design freedom is achieved. Since
current mode control is utilized, current is restricted in
each cycle and excellent performance is demonstrated
in bandwidth and transient response.
The switching frequency is 65 kHz. At light load, the
switching frequency is reduced and high efficiency is
achieved.
A frequency hopping function is also on chip, which
contributes to low EMI.
We can design easily, because BM2PXX1 includes
the switching MOSFET.
Basic specifications
Operating Power Supply Voltage Range:
VCC 8.9V to 26.0V DRAIN:~650V
Operating Current: Normal Mode
BM2P011: 0.950mA (Typ.)
BM2P031: 0.775mA (Typ)
BM2P051: 0.600mA (Typ)
BM2P091: 0.500mA (Typ)
Burst Mode 0.400mA (Typ.)
Oscillation Frequency: 65kHz (Typ.)
Operating Temperature: - 40 oC to +105 oC
MOSFET ON Resistance:
BM2P011:1.4 (Typ)
BM2P031:2.4 (Typ)
BM2P051:4.0 (Typ)
BM2P091:8.5 (Typ)
Features
PWM frequency : 65kHz
PWM current mode method
Burst operation when load is light
Frequency reduction function
Built-in 650V start circuit
Built-in 650V switching MOSFET
VCC pin under voltage protection
VCC pin overvoltage protection
SOURCE pin Open protection
SOURCE pin Short protection
SOURCE pin Leading-Edge-Blanking function
Per-cycle over current protection circuit
Soft start
Secondary Over current protection circuit
BR pin AC input low voltage protection
BR pin AC input high voltage protection
Package
DIP7 9.20mm×6.35mm×4.30mm pitch 2.54mm
(Typ.) (Typ.) (Max.) (Typ.)
Applications
AC adapters and household appliances (vacuum
cleaners, humidifiers, air cleaners, air conditioners, IH
cooking heaters, rice cookers, etc.)
Line up
Application circuit
Figure 1. Application circuit
Product MOSFET ON resistore
BM2P011 1.4Ω
BM2P031 2.4Ω
BM2P051 4.0Ω
BM2P091 8.5Ω
2/19
Datasheet
Datasheet
BM2PXX1 Series
TSZ02201-0F2F0A200010-1-2
7.Mar.2017.Rev.006
© 2012 ROHM Co., Ltd. All rights reserved.
www.rohm.com
TSZ2211115001
Absolute Maximum RatingsTa=25C
Parameter Symbol Rating Unit Conditions
Maximum applied voltage 1 Vmax1 -0.330 V VCC
Maximum applied voltage 2 Vmax2 -0.36.5 V SOURCE,FB,BR
Maximum applied voltage 3 Vmax3 650 V DRAIN
Drain current pulse I
DP 10.40 A
PW=10us, Duty cycle=1%
(BM2P011)
Drain current pulse I
DP 5.20 A
PW=10us, Duty cycle=1%
(BM2P031)
Drain current pulse I
DP 2.60 A
PW=10us, Duty cycle=1%
(BM2P051)
Drain current pulse I
DP 1.30 A
PW=10us, Duty cycle=1%
(BM2P091)
Allowable dissipation Pd 2000 mW
Operating
temperature range Topr -40 +105 oC
MAX junction temperature Tjmax 150 oC
Storage
temperature range Tstr -55 +150 oC
(Note1) DIP7 : When mounted (on 74.2 mm × 74.2 mm, 1.6 mm thick, glass epoxy on double-layer substrate).
Reduce to 16 mW/C when Ta = 25C or above.
Operating ConditionsTa=25C
Parameter Symbol Rating Unit Conditions
Power supply voltage range 1 VCC 8.926.0 V VCC pin voltage
Power supply voltage range 2 VDRAIN 650 V DRAIN pin voltage
Electrical Characteristics of MOSFET part (Unless otherwise noted, Ta = 25C, VCC = 15 V)
Parameter Symbol Specifications Unit Conditions
Min Typ Max
[MOSFET Block]
Between drain and
source voltage V(BR)DDS 650 - - V ID=1mA / VGS=0V
Drain leak current IDSS - - 100 uA VDS=650V / VGS=0V
On resistance RDS(ON) - 1.4 2.0 ID=0.25A / VGS=10V
(BM2P011)
On resistance RDS(ON) - 2.4 3.6 ID=0.25A / VGS=10V
(BM2P031)
On resistance RDS(ON) - 4.0 5.5 ID=0.25A / VGS=10V
(BM2P051)
On resistance RDS(ON) - 8.5 12.0 ID=0.25A / VGS=10V
(BM2P091)
3/19
Datasheet
Datasheet
BM2PXX1 Series
TSZ02201-0F2F0A200010-1-2
7.Mar.2017.Rev.006
© 2012 ROHM Co., Ltd. All rights reserved.
www.rohm.com
TSZ2211115001
Electrical Characteristics of Control IC part(Unless otherwise noted, Ta = 25C, VCC = 15 V)
Parameter Symbol Specifications Unit Conditions
Min Typ Max
[Circuit current]
Circuit current (ON) 1 ION1 700 950 1200 μA BM2P011, FB=2.0V
( at pulse operation)
Circuit current (ON) 1 ION1 550 775 1050 μA BM2P031, FB=2.0V
(at pulse operation)
Circuit current (ON) 1 ION1 410 600 790 μA BM2P051, FB=2.0V
(at pulse operation)
Circuit current (ON) 1 ION1 350 500 650 μA BM2P091, FB=2.0V
(at pulse operation)
Circuit current (ON) 2 ION2 - 400 500 μA FB=0.0V
(at burst operation)
[VCC protection function]
VCC UVLO voltage 1 VUVLO1 12.50 13.50 14.50 V VCC rises
VCC UVLO voltage 2 VUVLO2 7.50 8.20 8.90 V VCC falls
VCC UVLO hysteresis VUVLO3 - 5.30 - V VUVLO3= VUVLO1- VUVLO2
VCC OVP voltage 1 VOVP1 26.0 27.5 29.0 V VCC rises
Latch released VCC voltage VLATCH - VUVLO2-0.5 - V
VCC Recharge start voltage VCHG1 7.70 8.70 9.70 V
VCC Recharge stop voltage VCHG2 12.00 13.00 14.00 V
Latch mask time TLATCH 50 100 150 us
Thermal shut down
temperature TSD 118 145 - C Control IC
[PWM type DCDC driver block]
Oscillation frequency 1 FSW1 60 65 70 KHz FB=2.00V
Oscillation frequency 2 FSW2 20 25 30 KHz FB=0.40V
Frequency hopping width 1 FDEL1 - 4.0 - KHz FB=2.0V
Hopping fluctuation frequency FCH 75 125 175 Hz
Soft start time 1 TSS1 0.30 0.50 0.70 ms
Soft start time 2 TSS2 0.60 1.00 1.40 ms
Soft start time 3 TSS3 1.20 2.00 2.80 ms
Soft start time 4 TSS4 4.80 8.00 11.20 ms
Maximum duty Dmax 68.0 75.0 82.0 %
FB pin pull-up resistance RFB 23 30 37 k
ΔFB / ΔCS gain Gain - 4.00 - V/V
FB burst voltage VBST 0.300 0.400 0.500 V FB falls
FB voltage of
starting Frequency reduction
mode
VDLT 1.100 1.250 1.400 V
FB OLP voltage 1a VFOLP1A 2.60 2.80 3.00 V
Overload is detected (FB
rise)
FB OLP voltage 1b VFOLP1B - 2.60 - V
Overload is detected (FB
drop)
FB OLP ON timer TFOLP1 40 64 88 ms
FB OLP Start up timer TFOLP1b 26 32 38 ms
FB OLP OFF timer TFOLP2 358 512 666 ms
[Ove
r
current detection block]
Overcurrent detection voltage VCS 0.380 0.400 0.420 V Ton=0us
Overcurrent detection voltage
SS1 VCS_SS1 - 0.100 - V 0[ms] ~ TSS1[ms]
Overcurrent detection voltage
SS2 VCS_SS2 - 0.150 - V TSS1 [ms] ~ TSS2 [ms]
Overcurrent detection voltage
SS3 VCS_SS3 - 0.200 - V TSS2 [ms] ~ TSS3[ms]
Overcurrent detection voltage
SS4 VCS_SS4 - 0.300 - V TSS3 [ms] ~ TSS4 [ms]
Leading Edge Blanking Time TLEB - 250 - ns
Over current detection AC
Voltage compensation factor KCS 12 20 28 mV/us
SOURCE pin
short protection voltage VCSSHT 0.020 0.050 0.080 V
4/19
Datasheet
Datasheet
BM2PXX1 Series
TSZ02201-0F2F0A200010-1-2
7.Mar.2017.Rev.006
© 2012 ROHM Co., Ltd. All rights reserved.
www.rohm.com
TSZ2211115001
Electrical Characteristics of Control IC part (Unless otherwise noted, Ta = 25C, VCC = 15 V)
Parameter Symbol Specifications Unit Conditions
Min Typ Max
[Start circuit block]
Start current 1 ISTART1 0.100 0.500 1.000 mA VCC= 0V
Start current 2 ISTART2 1.000 3.000 6.000 mA VCC=10V
OFF current ISTART3 - 10 20 uA
Inflow current from Drain
pin after UVLO released
UVLO.
When MOSFET is OFF
Start current switching voltage VSC 0.800 1.500 2.100 V
[BR pin function]
BR UVLO detection voltage1 VBR1 0.45 0.50 0.55 V BR rises
BR UVLO voltage 2 VBR2 0.29 0.35 0.41 V BR falls
BR UVLO hysteresis VBR3 - 0.15 - V VBR3=VBR1-VBR2
BR UVLO detection delay
time1 TBR1 50 100 150 us BR rises
BR UVLO detection delay
time2 TBR2 150 256 350 ms BR falls
BR OVP detection voltage1 VBR4 2.00 2.10 2.20 V BR rises
BR OVP detection valtage2 VBR5 1.90 2.00 2.10 V BR falls
BR OVP hysteresis VBR6 - 0.10 - V VBR6=VBR4-VBR5
BR OVP detection delay time1 TBR3 50 100 150 us BR rises
BR OVP detection delay time2 TBR4 50 100 150 us BR falls
PIN DESCRIPTIONS
Table 1. Pin Description
NO. Pin Name I/O Function ESD Diode
VCC GND
1 SOURCE I/O MOSFET SOURCE pin
2 BR I Input AC voltage monitor pin -
3 GND I/O GND pin -
4 FB I Feedback signal input pin -
5 VCC I Power supply input pin -
6 DRAIN I/O MOSFET DRAIN pin - -
7 DRAIN I/O MOSFET DRAIN pin - -
I/O Equivalent Circuit Diagram
7
GND FB
6DRAIN
1SOURCE 2
DRAIN
VCC
3
BR
GND
5VCC
4
DRAIN
SOURCE
Internal MOSFET
Internal
Circuit
BR
+
-
Internal
Circuit
VREF VREF
RFB
FB
SOURCE
VREF
DRAIN
SOURCE
Internal MOSFET
Internal
Circuit
Figure 2. I/O Equivalent Circuit Diagram
5/19
Datasheet
Datasheet
BM2PXX1 Series
TSZ02201-0F2F0A200010-1-2
7.Mar.2017.Rev.006
© 2012 ROHM Co., Ltd. All rights reserved.
www.rohm.com
TSZ2211115001
Block Diagram
FeedBack
With
Isolation
VO
AC
FUSE
+
-
Filter Diode
Bridge
PWM Control
Leading Edge
Blanking
(typ=250ns)
VCC UVLO
13.5V/ 8 .2V
DRAIN
DRIVE R
S
QR
+
-
Current
Limiter
PWM
Comparator
+
-
+
+
-
Burst
Comparator
GND
Slope
Com pens ation
VCC
FB
SOURCE
+
-
30 k
+
-
OLP
Internal Block
+
-
VCC OVP
27.5V
4.0V
.
Cvcc
VH
Vs
CM
Rs
Soft St a r t AC Input
Compensation
OSC
(6 5kH z )
Frequency
Hopping
100us
Filter
5
4
64ms
Time r
MAX
DUTY
3
1
12 V C lamp
Circuit
4.0V
Line Reg
7
4. 0V
1M
Starter
10uA
6
DRAIN
+
-
100 us
Filter
2. 0V /2 . 1 V
+
-
256 m s
Timer
0.50 V/0. 35V
R
BR2
R
BR1
2
Figure 3. Block Diagram
RS
VCC DRAIN DRAIN
BR
6/19
Datasheet
Datasheet
BM2PXX1 Series
TSZ02201-0F2F0A200010-1-2
7.Mar.2017.Rev.006
© 2012 ROHM Co., Ltd. All rights reserved.
www.rohm.com
TSZ2211115001
Description of Blocks
(1) Start circuit (DRIAN: 6,7pin)
This IC built in Start circuit (tolerates 650V). It enables to be low standby mode and high speed starting.
After starting, consumption power is idling current ISTART3typ=10uA only.
Reference values of Starting time are shown in Figure 6. When Cvcc=10uF it can start less than 0.1 sec.
+
-
VCCUVLO
VCC
Cvcc
DRAIN
FUSE
+
-
Diode
Bridge
SW1
AC
85- 265 Vac
Figure 4. Block diagram of start circuit
ISTART1
ISTART2
Vsc VUVLO1
10V
VCC Voltage[V]
ISTART3
0
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
0 5 10 15 20 25 30 35 40 45 50
起動時間[sec]
Cvcc[uF]
Start Time
Figure 5. Start current vs VCC voltage Figure 6. Start time (reference value)
* Start current flows from the DRAIN pin
ex) Consumption power of start circuit only when the Vac=100V
PVH100V*2*10uA=1.41mW
ex) Consumption power of start circuit only when the Vac=240V
PVH240V*2*10uA=3.38mW
7/19
Datasheet
Datasheet
BM2PXX1 Series
TSZ02201-0F2F0A200010-1-2
7.Mar.2017.Rev.006
© 2012 ROHM Co., Ltd. All rights reserved.
www.rohm.com
TSZ2211115001
(2) Start sequences
(Soft start operation, light load operation, and auto recovery operation during overload protection)
Start sequences are shown in Figure 7. See the sections below for detailed descriptions.
Vout
Switching
VH
VCC(1pin)
FB(8pin)
Soft
Start
64ms
Iout
Normal Load
Light LOAD
Within
32ms
VCC=8.2V
Over Load
Internal REF
Pull Up
Burst mode
AB
CDEF
GH I
Switching
stop
VCC=13.5V
FB OLP ON
Figure 7. Start sequences Timing Chart
A: Input voltage VH is applied
B: This IC starts operation when VCC pin voltage rises and VCC > VUVLO1 (13.5 V typ).Switching function starts when
other protection functions are judged as normal. Until the secondary output voltage becomes constant level, VCC
voltage drops because of the VCC consumption current. VCC recharge function start if VCC voltage < VCHG18.7V typ
C: With the soft start function, over current limit value is restricted to prevent any excessive rise in voltage or current.
D: When the switching operation starts, VOUT rises.The output voltage become to stable state, VCC voltage also become
to stable state through auxiliary winding. Please set the rated voltage within the TFOLP1B period (32ms typ) from VCC
voltage > VUVLO1.
E: During a light load, if it reaches FB voltage < VBST (= 0.4Vtyp), the IC starts burst operation to keep power consumption
low. During burst operation, it becomes low-power consumption mode.
F: When the FB VoltageVFOLP1A=2.8V typ, it becomes a overload operation.
G: When FB pin voltage keeps VFOLP1A (= 2.8V typ) at or above T FOLP1 (64ms typ), the overload protection function is
triggered and switching stops 64ms later. If the FB pin voltage becomes FB<VFOLP1B even once, the IC’s FB OLP timer is
reset.
H: If the VCC voltage drops to VCC < VUVLO2 (8.2Vtyp) or below, restart is executed.
I: The IC’s circuit current is reduced and the VCC pin value rises. (Same as B)
8/19
Datasheet
Datasheet
BM2PXX1 Series
TSZ02201-0F2F0A200010-1-2
7.Mar.2017.Rev.006
© 2012 ROHM Co., Ltd. All rights reserved.
www.rohm.com
TSZ2211115001
(3) VCC pin protection function
BM2PXX1 built in VCC low voltage protection function VCCUVLO (Under Voltage Lock Out), over voltage protection
function VCC OVP (Over Voltage Protection) and VCC charge function that operates in case of dropping the VCC voltage.
VCC UVLO and VCC OVP monitor VCC pin and prevent VCC pin from destroying switching MOSFET at abnormal
voltage.
VCC charge function stabilizes the secondary output voltage by charging from the high voltage line by start circuit at
dropping the VCC voltage
(3-1) VCC UVLO VCC OVP function
VCCUVLO is auto recovery protection. VCCOVP is latch protection. Refer to the operation figure-8.
VCCOVP built in mask time TLATCHtyp=100us.By this function, this IC masks pin generated surge etc.
This function operates detection in case of continuing VCC pin voltage > VOVP1 typ=27.5V.
VUVLO1
ON
OFF
VOVP1
VCHG1
ON
OFF
OFF
ON
OFF
ABC D FG H IJ
VUVLO2
A
ON
ON
OFF
ON
VCHG2
E
VLATCH
K
Figure 8. VCC UVLO / OVP Timing Chart
A: DRAIN voltage inputs, VCC pin voltage starts rising.
B: VCC>VUVLO1, DC/DC operation starts
C: VCC< VCHG1, VCC charge function operates and the VCC voltage rises.
D: VCC > VCHG2, VCC charge function is stopped.
E: VCC > VOVP1, VCCOVP function is detected
F: VCC > VOVP1, continues for TLATCH (typ =100us), switching is latched stopped by the VCCOVP function.
G: VH is open.VCC voltage is fall.
H: Same as C.
I: Same as D.
J: VCC<VUVLO2, switching is stopped by the VCC UVLO function
K: VCC< VLATCH, released from latch
9/19
Datasheet
Datasheet
BM2PXX1 Series
TSZ02201-0F2F0A200010-1-2
7.Mar.2017.Rev.006
© 2012 ROHM Co., Ltd. All rights reserved.
www.rohm.com
TSZ2211115001
(3-2) VCC Charge function
After VCC charge function operates once the VCC pin >VUVLO1 and the DC/DC operation starts then the VCC pin voltage
drops to <VCHG1. At that time the VCC pin is charged from DRAIN pin through start circuit.
For this operation, BM2PXX1 doesn’t occur to start failure.
When VCC pin voltage rises to VCC >VCHG2, charge is stopped. The operations are shown in figure 9.
VCC
VUVLO1
VUVLO2
VCHG1
Switching
VH charge
charge charge
OUTPUT
voltage
VCHG2
charge charge
ABCDEFGH
VH
Figure 9. Charge operation VCC pin charge operation
A: DRAIN pin voltage rises, charge starts to VCC pin by the VCC charge function.
B: VCC > VUVLO1, VCC UVLO function releases, VCC charge function stops, DC/DC operation starts.
C: When DC/DC operation starts, the VCC voltage drops.
D: VCC < VCHG1, VCC recharge function operates and VCC pin voltage rises.
E: VCC > VCHG2, VCC recharge function stops.
F: VCC < VCHG1, VCC recharge function operates and VCC pin voltage rises.
G: VCC > VCHG2, VCC recharge function stops.
H: After start of output voltage finished, VCC is charged by the auxiliary winding VCC pin stabilizes.
10/19
Datasheet
Datasheet
BM2PXX1 Series
TSZ02201-0F2F0A200010-1-2
7.Mar.2017.Rev.006
© 2012 ROHM Co., Ltd. All rights reserved.
www.rohm.com
TSZ2211115001
(4) DCDC driver (PWM comparator, frequency hopping, slope compensation, OSC, burst)
BM2PXX1 is current mode PWM control.
An internal oscillator sets a fixed switching frequency (65 kHz typ).
BM2PXX1 is integrated switching frequency hopping function which changes the switching frequency to fluctuate as
shown in figure-10 below.
The fluctuation cycle is 125 Hz typ.
65
Switching Frequency
[kHz]
69
125 Hz(8ms)
Time
61
62
63
64
66
68
67
500us
Figure 10. Frequency hopping function
Max duty cycle is fixed as 75% (typ) and MIN pulse width is fixed as 400 ns (typ).
With current mode control, when the duty cycle exceeds 50% sub harmonic oscillation may occur.
As a countermeasure to this, BM2PXX1 is built in slope compensation circuits.
BM2PXX1 is built in burst mode circuit and frequency reduction circuit to achieve lower power consumption, when the load
is light.
FB pin is pull up by RFB (30 k typ).
FB pin voltage is changed by secondary output voltage (secondary load power).
FB pin is monitored, burst mode operation and frequency detection start.
Figure 11 shows the FB voltage, and switching frequency, DCDC operation
mode1: Burst operation
mode2: Frequency reduction operation.
mode3: Fixed frequency operation.(operate at the max frequency)
mode4: Over load operation.(detect the over load state and stop the pulse operation)
Figure 11. Switching operation state changes by FB pin voltage
11/19
Datasheet
Datasheet
BM2PXX1 Series
TSZ02201-0F2F0A200010-1-2
7.Mar.2017.Rev.006
© 2012 ROHM Co., Ltd. All rights reserved.
www.rohm.com
TSZ2211115001
(5) Over Current limiter
BM2PXX1 is built in Over Current limiter per cycle. If the SOURCE pin over a certain voltage, switching is stopped. It
is also built in AC voltage compensation function. This is the function which compensates the maximum power as the
AC voltage’s change by increasing over current limiter with time.
. Shown in figure-12, 13, and 14.
ON
OFF
OFF
[DC/DC]
@AC100V
Iepak(DC)= included conpensation
Tdelay
Iepak(AC)@Vin=100V
Iepak(AC)@Vin=240V
ON
OFF
OFF
[DC/DC]
@AC100V
65kHz(15.3us)
Primary Peak Current
Tdelay
Figure 12. No AC voltage compensation function Figure13. built-in AC compensation voltage
Primary peak current is decided as the formula below.
Primary peak current: I
peak = Vcs/Rs + Vdc/Lp*Tdelay
VcsOver current limiter voltage internal IC, RsCurrent detection resistance, Vdc input DC voltage, LpPrimary inductance,
Tdelaydelay time after detection of over current limiter
Figure 14. Over current limiter voltage
(6) L.E.B period
When the driver MOSFET is turned ON, surge current occurs at each capacitor component and drive current.
Therefore, because when SOURCE pin voltage rises temporarily, the detection errors may occur in the over current limiter
circuit.
To prevent detection errors, DRAIN is switched from high to low and the SOURCE signal is masked for 250 ns by the
on-chip LEB (Leading Edge Blanking) function.
12/19
Datasheet
Datasheet
BM2PXX1 Series
TSZ02201-0F2F0A200010-1-2
7.Mar.2017.Rev.006
© 2012 ROHM Co., Ltd. All rights reserved.
www.rohm.com
TSZ2211115001
(7) SOURCE pin (1pin) short protection function
When the SOURCE pin (1pin) is shorted, BM2PXX1 is over heat.
BM2PXX1 built in short protection function to prevent destroying.
(8) SOURCE pin (1pin) open protection
If the SOURCE pin becomes OPEN, BM2PXX1 may be damaged.
To prevent to be damaged, BM2PXX1 built in OPEN protection circuitauto recovery protection.
(9) Output over load protection functionFB OLP Comparator
The output overload protection function monitors the secondary output load status at the FB pin, and stops switching when
an overload occurs. In case of overload, the output voltage is reduced and current no longer flows to the photo coupler, so
the FB pin voltage rises.
When the FB pin voltage > VFOLP1A (2.8 V typ) continuously for the period TFOLP1 (64ms typ), it is judged as an overload and
stops switching.
When the FB pin > VFOLP1A (2.8 V typ), if the voltage goes lower than VFOLP1B (2.6V typ) during the period TFOLP1 (64ms typ),
the overload protection timer is reset. The switching operation is performed during this period TFOLP1 (64ms typ).
At startup, the FB voltage is pulled up to the IC’s internal voltage, so operation starts at a voltage of VFOLP1A (2.8 V typ) or
above. Therefore, at startup, the FB voltage must be set to go down to VFOLP1B (2.6V typ) or below during the period TFOLP1
(64ms typ), and the secondary output voltage’s start time must be set within the period TFOLP1 (64ms typ) following startup of
the IC.
Recovery from the once detection of FBOLP, after the period TFOLP2 (512 ms typ)
VCC
VUVLO 1
VUVLO 2
VCHG1
Switching
FB VFOLP 1A
64ms 64ms
512ms
VH
charge
chargecharge
512ms
VCHG 2
ABCDE FGH
Figure 15. Over load protection (Auto recovery)
A: The FBOLP comparator detects over load for FB>VFOLP1A
B: If the State of A continues for the period TFOLP1 (64ms typ), it is judged as an overload and stops switching after
64ms.
C: While switching stops for the over load protection function, the VCC pin voltage drops and VCC pin voltage reaches
< VCHG1, the VCC charge function operates so the VCC pin voltage rises.
D: VCC charge function stops when VCC pin voltage > VCHG2
E: If TFOLP2 typ =512ms go on from B point, Switching function starts on soft start.
F: If TFOLP1typ=64ms go on from E point to continues a overload condition (FB>VFOLP1A), Switching function stops
at F point.
G: While switching stops VCC pin voltage drops to < VCHG1, VCC charge function operates and VCC pin voltage rises.
H: If VCC pin (5pin) voltage becomes over VCHG2 by the VCC charge function, VCC charge function operation stops.
13/19
Datasheet
Datasheet
BM2PXX1 Series
TSZ02201-0F2F0A200010-1-2
7.Mar.2017.Rev.006
© 2012 ROHM Co., Ltd. All rights reserved.
www.rohm.com
TSZ2211115001
(10) Input voltage protection function
This IC has BR-UVLO function and BR-OVP function to monitor input voltage. By monitoring input voltage, it can be
prevented from breaking of IC. AC voltage and DC voltage can be monitored by BR pin.
Figure 16(a). AC voltage monitor setting Figure 16(b). DC voltage monitor setting
BRUVLO function can protect the breaking of IC when input voltage is low.
14/19
Datasheet
Datasheet
BM2PXX1 Series
TSZ02201-0F2F0A200010-1-2
7.Mar.2017.Rev.006
© 2012 ROHM Co., Ltd. All rights reserved.
www.rohm.com
TSZ2211115001
Operation mode of protection circuit
Operation mode of protection functions are shown in table2.
Table 2. Operation mode of protection circuit
Function Operation mode
VCC Under Voltage Locked Out Auto recovery
VCC Over Voltage Protection Latchwith 100us timer
TSD Latchwith 100us timer
FB Over Limited Protection Auto recoverywith 64ms timer
SOURCE Open Protection Auto recovery
BR UVLO Auto recovery (with 256ms )
BR OVP Auto recovery with 100us timer
Sequence
The sequence diagram is show in Fig 17.
All condition transits OFF Mode VCC<8.2V
Soft Start 1
Soft Start 4
Burst MODE & Low Power MODE
* Pulse OFF
Normal MODE
OFF MODE
OLP MODE
( Pulse Stop)
LATCH OFF
MODE
(Pulse
Stop )
Soft Start 2
Soft Start 3
BR UVLO
( Pulse Stop)
PULSE OFF
FBOLP
OFF TIMER
( 512ms)
BR OVP
(Pulse Stop)
SOURCE OPEN
(Pulse Stop)
Figure 17. The sequence diagram
LATCH OFF
15/19
Datasheet
Datasheet
BM2PXX1 Series
TSZ02201-0F2F0A200010-1-2
7.Mar.2017.Rev.006
© 2012 ROHM Co., Ltd. All rights reserved.
www.rohm.com
TSZ2211115001
Thermal loss
The thermal design should set operation for the following conditions.
(Since the temperature shown below is the guaranteed temperature, be sure to take a margin into account.)
1. The ambient temperature Ta must be 105 or less.
2. The IC’s loss must be within the allowable dissipation Pd.
The thermal abatement characteristics are as follows.
(PCB: 74.2 mm × 74.2mm × 1.6 mm, mounted on glass epoxy double-layer substrate)
Figure 18. DIP7 Thermal Abatement Characteristics
0
500
1000
1500
2000
2500
3000
0 25 50 75 100 125 150
Pd[mW]
Ta[]
16/19
Datasheet
Datasheet
BM2PXX1 Series
TSZ02201-0F2F0A200010-1-2
7.Mar.2017.Rev.006
© 2012 ROHM Co., Ltd. All rights reserved.
www.rohm.com
TSZ2211115001
Ordering Information
B M 2 P X X 1
-
Product
name
Package
None: DIP7 Packaging and forming specification
None: Tube
Physical Dimension Tape and Reel Information
DIP7
Making Diagram Line-Up
DIP7
Product name (BM2PXX1)
BM2P011
BM2P031
BM2P051
BM2P091
Order quantity needs to be multiple of the minimum quantity.
<Tape and Reel information>
TubeContainer
Quantity
Direction of feed 2000pcs
Direction of products is fixed in a container tube
2PXX1
Part Number Marking
LOT Numbe
r
17/19
Datasheet
Datasheet
BM2PXX1 Series
TSZ02201-0F2F0A200010-1-2
7.Mar.2017.Rev.006
© 2012 ROHM Co., Ltd. All rights reserved.
www.rohm.com
TSZ2211115001
Operational Notes
1. Reverse Connection of Power Supply
Connecting the power supply in reverse polarity can damage the IC. Take precautions against reverse polarity when
connecting the power supply, such as mounting an external diode between the power supply and the IC’s power
supply pins.
2. Power Supply Lines
Design the PCB layout pattern to provide low impedance supply lines. Separate the GND and supply lines of the
digital and analog blocks to prevent noise in the GND and supply lines of the digital block from affecting the analog
block. Furthermore, connect a capacitor to GND at all power supply pins. Consider the effect of temperature and
aging on the capacitance value when using electrolytic capacitors.
3. GND Voltage
Ensure that no pins are at a voltage below that of the GND pin at any time, even during transient condition.
4. GND Wiring Pattern
When using both small-signal and large-current GND traces, the two GND traces should be routed separately but
connected to a single GND at the reference point of the application board to avoid fluctuations in the small-signal
GND caused by large currents. Also ensure that the GND traces of external components do not cause variations on
the GND voltage. The GND lines must be as short and thick as possible to reduce line impedance.
5. Thermal Consideration
Should by any chance the power dissipation rating be exceeded the rise in temperature of the chip may result in
deterioration of the properties of the chip. The absolute maximum rating of the Pd stated in this specification is when
the IC is mounted on a 70mm x 70mm x 1.6mm glass epoxy board. In case of exceeding this absolute maximum
rating, increase the board size and copper area to prevent exceeding the Pd rating.
6. Recommended Operating Conditions
These conditions represent a range within which the expected characteristics of the IC can be approximately obtained.
The electrical characteristics are guaranteed under the conditions of each parameter.
7. Inrush Current
When power is first supplied to the IC, it is possible that the internal logic may be unstable and inrush
current may flow instantaneously due to the internal powering sequence and delays, especially if the IC
has more than one power supply. Therefore, give special consideration to power coupling capacitance,
power wiring, width of GND wiring, and routing of connections.
8. Operation Under Strong Electromagnetic Field
Operating the IC in the presence of a strong electromagnetic field may cause the IC to malfunction.
9. Testing on Application Boards
When testing the IC on an application board, connecting a capacitor directly to a low-impedance output pin may
subject the IC to stress. Always discharge capacitors completely after each process or step. The IC’s power supply
should always be turned off completely before connecting or removing it from the test setup during the inspection
process. To prevent damage from static discharge, GND the IC during assembly and use similar precautions during
transport and storage.
10. Inter-pin Short and Mounting Errors
Ensure that the direction and position are correct when mounting the IC on the PCB. Incorrect mounting may result in
damaging the IC. Avoid nearby pins being shorted to each other especially to GND, power supply and output pin.
Inter-pin shorts could be due to many reasons such as metal particles, water droplets (in very humid environment) and
unintentional solder bridge deposited in between pins during assembly to name a few.
18/19
Datasheet
Datasheet
BM2PXX1 Series
TSZ02201-0F2F0A200010-1-2
7.Mar.2017.Rev.006
© 2012 ROHM Co., Ltd. All rights reserved.
www.rohm.com
TSZ2211115001
Operational Notes – continued
11. Unused Input Pins
Input pins of an IC are often connected to the gate of a MOS transistor. The gate has extremely high impedance and
extremely low capacitance. If left unconnected, the electric field from the outside can easily charge it. The small
charge acquired in this way is enough to produce a significant effect on the conduction through the transistor and
cause unexpected operation of the IC. So unless otherwise specified, unused input pins should be connected to the
power supply or GND line.
12. Regarding the Input Pin of the IC
This monolithic IC contains P+ isolation and P substrate layers between adjacent elements in order to keep them
isolated. P-N junctions are formed at the intersection of the P layers with the N layers of other elements, creating a
parasitic diode or transistor. For example (refer to figure below):
When GND > Pin A and GND > Pin B, the P-N junction operates as a parasitic diode.
When GND > Pin B, the P-N junction operates as a parasitic transistor.
Parasitic diodes inevitably occur in the structure of the IC. The operation of parasitic diodes can result in mutual
interference among circuits, operational faults, or physical damage. Therefore, conditions that cause these diodes to
operate, such as applying a voltage lower than the GND voltage to an input pin (and thus to the P substrate) should
be avoided.
Figure 19. Example of monolithic IC structure
13. Ceramic Capacitor
When using a ceramic capacitor, determine the dielectric constant considering the change of capacitance with
temperature and the decrease in nominal capacitance due to DC bias and others.
14. Area of Safe Operation (ASO)
Operate the IC such that the output voltage, output current, and power dissipation are all within the Area of Safe
Operation (ASO).
15. Thermal Shutdown Circuit(TSD)
This IC has a built-in thermal shutdown circuit that prevents heat damage to the IC. Normal operation
should always be within the IC’s power dissipation rating. If however the rating is exceeded for a
continued period, the junction temperature (Tj) will rise which will activate the TSD circuit that will turn
OFF all output pins. The IC should be powered down and turned ON again to resume normal
operation because the TSD circuit keeps the outputs at the OFF state even if the TJ falls below the
TSD threshold.
Note that the TSD circuit operates in a situation that exceeds the absolute maximum ratings and therefore, under no
circumstances, should the TSD circuit be used in a set design or for any purpose other than protecting the IC from heat
damage.
16. Over Current Protection Circuit (OCP)
This IC incorporates an integrated overcurrent protection circuit that is activated when the load is shorted. This
protection circuit is effective in preventing damage due to sudden and unexpected incidents. However, the IC should
not be used in applications characterized by continuous operation or transitioning of the protection circuit.
19/19
Datasheet
Datasheet
BM2PXX1 Series
TSZ02201-0F2F0A200010-1-2
7.Mar.2017.Rev.006
© 2012 ROHM Co., Ltd. All rights reserved.
www.rohm.com
TSZ2211115001
date Rev. No. Revision Point
2012.07.19 001 New Release
2013.11.18 003
P7 An explanation for Figure7
P8 An explanation for VCC_UVLO/VCC_OVP function
An explanation for Figure8
P11 An explanation for Over Current limiter
P12 An explanation for Output over load protection function
An explanation for Figure15
2015.05.15 004 P14 Operation mode of protection circuit
P14 Sequence
2015.09.24 005
P4 A value of BR UVLO detection voltage 1
P4 A value of BR UVLO voltage2
P4 A value of BR OVP detection voltage1
P4 A value of BR OVP detection voltage2
P7 An explanation of Start sequence
P8 An explanation of VCC pin protection function
P8 An explanation of VCC UVLO / VCC OVP function
P9 An explanation of VCC Charge function
P11 An explanation of Over Current Limiter
P12 An explanation of Output over load protection function
2017.03.07 006
P1 An explanation of package height
P2 Format for Electrical Characteristics of MOSFET
P3 Format for Electrical Characteristics of Control IC
P4 An explanation of BR OVP hysteresis
P5 An explanation of Figure3
P7 An explanation of Start sequences
P8 An explanation of Figure8
P9 An explanation of VCC pin protection function
P12 An explanation of OUTPUT over load protection function
P14 An explanation of Figure17
Notice-PGA-E Rev.003
© 2015 ROHM Co., Ltd. All rights reserved.
Notice
Precaution on using ROHM Products
1. Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment,
OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you
intend to use our Products in devices requiring extremely high reliability (such as medical equipment (Note 1), transport
equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car
accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or
serious damage to property (Specific Applications), please consult with the ROHM sales representative in advance.
Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any
damages, expenses or losses incurred by you or third parties arising from the use of any ROHMs Products for Specific
Applications.
(Note1) Medical Equipment Classification of the Specific Applications
USA
EU
CLASS
CLASSb
CLASS
2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate
safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which
a failure or malfunction of our Products may cause. The following are examples of safety measures:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure
3. Our Products are designed and manufactured for use under standard conditions and not under any special or
extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any
special or extraordinary environments or conditions. If you intend to use our Products under any special or
extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of
product performance, reliability, etc, prior to use, must be necessary:
[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents
[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust
[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,
H2S, NH3, SO2, and NO2
[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items
[f] Sealing or coating our Products with resin or other coating materials
[g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of
flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning
residue after soldering
[h] Use of the Products in places subject to dew condensation
4. The Products are not subject to radiation-proof design.
5. Please verify and confirm characteristics of the final or mounted products in using the Products.
6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.
7. De-rate Power Dissipation depending on ambient temperature. When used in sealed area, confirm that it is the use in
the range that does not exceed the maximum junction temperature.
8. Confirm that operation temperature is within the specified range described in the product specification.
9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in
this document.
Precaution for Mounting / Circuit board design
1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product
performance and reliability.
2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must
be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products,
please consult with the ROHM representative in advance.
For details, please refer to ROHM Mounting specification
Notice-PGA-E Rev.003
© 2015 ROHM Co., Ltd. All rights reserved.
Precautions Regarding Application Examples and External Circuits
1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the
characteristics of the Products and external components, including transient characteristics, as well as static
characteristics.
2. You agree that application notes, reference designs, and associated data and information contained in this document
are presented only as guidance for Products use. Therefore, in case you use such information, you are solely
responsible for it and you must exercise your own independent verification and judgment in the use of such information
contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses
incurred by you or third parties arising from the use of such information.
Precaution for Electrostatic
This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper
caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be
applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron,
isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).
Precaution for Storage / Transportation
1. Product performance and soldered connections may deteriorate if the Products are stored in the places where:
[a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2
[b] the temperature or humidity exceeds those recommended by ROHM
[c] the Products are exposed to direct sunshine or condensation
[d] the Products are exposed to high Electrostatic
2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period
may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is
exceeding the recommended storage time period.
3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads
may occur due to excessive stress applied when dropping of a carton.
4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of
which storage time is exceeding the recommended storage time period.
Precaution for Product Label
A two-dimensional barcode printed on ROHM Products label is for ROHMs internal use only.
Precaution for Disposition
When disposing Products please dispose them properly using an authorized industry waste company.
Precaution for Foreign Exchange and Foreign Trade act
Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign
trade act, please consult with ROHM in case of export.
Precaution Regarding Intellectual Property Rights
1. All information and data including but not limited to application example contained in this document is for reference
only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any
other rights of any third party regarding such information or data.
2. ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the
Products with other articles such as components, circuits, systems or external equipment (including software).
3. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any
third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM
will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to
manufacture or sell products containing the Products, subject to the terms and conditions herein.
Other Precaution
1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.
2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written
consent of ROHM.
3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the
Products or this document for any military purposes, including but not limited to, the development of mass-destruction
weapons.
4. The proper names of companies or products described in this document are trademarks or registered trademarks of
ROHM, its affiliated companies or third parties.
DatasheetDatasheet
Notice – WE Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
General Precaution
1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents.
ROHM shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny
ROHM’s Products against warning, caution or note contained in this document.
2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior
notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s
representative.
3. The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all
information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or
liable for an y damages, expenses or losses incurred by you or third parties resulting from inaccur acy or errors of or
concerning such information.
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
ROHM Semiconductor:
BM2P031 BM2P011 BM2P091 BM2P051